doors 2000 builders fixing details i sectional garage door

STANDARD HEADROOM Headroom: 320mm Sideroom: 120mm Backspace: Door height + 900mm Headroom: 220mm Sideroom: 120mm Backspace: Door height + 1100mm CENTRE SUPPORT FOR FIXING OF SPRINGS AND AUTOMATIC POLE (3 x 100m x 50mm) NOTE: - It is recommended to “square stop” bewteen lintel & ceiling - Architrave Options - 40mm around perimeter - 140mm floor to ceiling 40MM ARCHITRAVE REBATE DETAIL JACKSTUDS TRIPLE STUDS “Z” “Y” NOG TRACK AUTOMATIC “X” ALL NOGS MUST BE PARALLEL WITH OPENING (Approx 400mm) 200mm 1m 100mm 100mm 100mm HEADROOM OPENING HEIGHT 20mm (APPROX) 1m 1m 1m “Y” “X” POWERPOINT - 500mm FURTHER BACK THAN NOG - 200mm OFF CENTRE NOG (600mm) FOR AUTO MUST BE IN LINE WITH CENTRE OF DOOR OPENING We recommend square stopping gib at lintel as Gib Cove can interfere with spring/automatic fixing. If Gib Cove used it may require notching out which can look untidy. SIDE ROOM OPENING WIDTH REBATE WIDTH = OPENING WIDTH + 200mm NOTE: INSIDE SURFACE OF OPENING SHOULD BE FLUSH DOORS 2000 BUILDERS FIXING DETAILS I SECTIONAL GARAGE DOOR LOW HEADROOM DOUBLE TRACK PLEASE ENSURE GARAGE FLOOR IS CLEAR OF OBSTRUCTION BEFORE INSTALLER ARRIVES DOOR HEIGHT “X” “Y” “Z” Up to 2200mm - 2100 2950 From 2201 - 2400 1600 2400 2950 From 2401 - 2700 1600 2700 3350 From 2701 - 3500 2000 3500 1900/3850

Upload: others

Post on 31-Dec-2021

4 views

Category:

Documents

0 download

Report

Download

Embed Size (px):

TRANSCRIPT

Page 1: DOORS 2000 BUILDERS FIXING DETAILS I SECTIONAL GARAGE DOOR

STANDARD HEADROOM

Headroom: 320mmSideroom: 120mmBackspace: Door height + 900mm

Headroom: 220mmSideroom: 120mmBackspace: Door height + 1100mm

CENTRE SUPPORT FOR FIXING OFSPRINGS AND AUTOMATIC POLE(3 x 100m x 50mm)

NOTE:- It is recommended to “square stop” bewteen lintel & ceiling- Architrave Options - 40mm around perimeter - 140mm floor to ceiling

40MM ARCHITRAVE

REBATE DETAIL

JACKSTUDS

TRIPLE STUDS

“Z”

“Y”

NOG

TRACK AUTOMATIC

“X”

ALL NOGS MUSTBE PARALLEL WITHOPENING(Approx 400mm)

200mm

100mm

HEAD

ROOM

OPEN

ING

HEIG

20m

m (A

PPRO

“Y”“X”

POWERPOINT- 500mm FURTHER BACKTHAN NOG- 200mm OFF CENTRE

NOG (600mm) FOR AUTO MUST BE IN LINEWITH CENTRE OFDOOR OPENING

We recommend square stopping gib at lintel as Gib Cove can interfere with spring/automatic fixing. If Gib Cove used it may require notching out which can look untidy.

SIDE ROOM

OPENING WIDTH

REBATE WIDTH = OPENING WIDTH + 200mm

NOTE: INSIDE SURFACE OFOPENING SHOULD BE FLUSH

DOORS 2000 BUILDERS FIXING DETAILS I SECTIONAL GARAGE DOOR

LOW HEADROOMDOUBLE TRACK

PLEASE ENSURE GARAGE FLOOR IS CLEAR OF OBSTRUCTION BEFORE INSTALLER ARRIVES

DOOR HEIGHT “X” “Y” “Z”Up to 2200mm - 2100 2950From 2201 - 2400 1600 2400 2950From 2401 - 2700 1600 2700 3350From 2701 - 3500 2000 3500 1900/3850

NEVADA Corner Sectional · during initial assembly. Only upon completion of the assembly should all fixing points 4. To ensure an easier assembly, we strongly advise that all fittings

Cross sectional study 2015 - Mahidol University€¦ · Descriptive cross-sectional study Analytic cross-sectional study Repeated cross-sectional study 7 Descriptive Collected number

A guide to help builders measure productivity of various ...€¦ · 2. Reinforcement Placing and Fixing 8 2.1 Reinforcement Placing and Fixing Process 9 2.1.1 Preparation of Reinforcement

Fixing Tenure