door products edges and a mestek company astragals - anemostat
TRANSCRIPT
DETAIL DRAWING
®
TECHnICaL DaTaFroM
A MESTEK COMPANYP.o. BoX 4938 • 1220 WaTSonCEnTEr roaD
CarSon, Ca 90745-4206(310) 835-7500 • FaX (310) 835-0448
e-mail: [email protected] • website: www.anemostat.com
®
DOOR PRODUCTS
INDEXFor
EDGES ANDASTRAGALS
MODEL DESCRIPTION DATE PRINTED PAGEHardware Prep Sheet forMetal Edges and Astragals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . January 2015 . . . . . . . . . . B
FMEA . . . . . . . . . . . . . . . . . . . . . . . . . . Metal Edge and astragal Pair . . . . . . . . . . . . . . . . . . . . . January 2015 . . . . . . . . . . 1
WV-FMEA . . . . . . . . . . . . . . . . . . . . . . Wood Veneer over Metal Edge and astragal Pair . . . . . January 2015 . . . . . . . . . . 2
FME. . . . . . . . . . . . . . . . . . . . . . . . . . . . Pair of Metal Edges. . . . . . . . . . . . . . . . . . . . . . . . . . . . . January 2015 . . . . . . . . . . 3
WV-FME . . . . . . . . . . . . . . . . . . . . . . . Pair of Wood Veneer over Metal Edges . . . . . . . . . . . . . January 2015 . . . . . . . . . . 4
FMA . . . . . . . . . . . . . . . . . . . . . . . . . . . Metal astragal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . January 2015 . . . . . . . . . . 5
FBA . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flat Metal astragal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . January 2015 . . . . . . . . . . 6
DE-FMEA . . . . . . . . . . . . . . . . . . . . . . Double Egress, Metal Edge and astragal pair . . . . . . . . January 2015 . . . . . . . . . . 7
DE-FME . . . . . . . . . . . . . . . . . . . . . . . . Double Egress, Pair of Metal Edge. . . . . . . . . . . . . . . . . January 2015 . . . . . . . . . . 8
DE-FMA . . . . . . . . . . . . . . . . . . . . . . . . Double Egress, Metal astragal . . . . . . . . . . . . . . . . . . . . January 2015 . . . . . . . . . . 9
X-RAY. . . . . . . . . . . . . . . . . . . . . . . . . . FMa, DE-FMa, FMEa, DE-FMEa - Lead Lined . . . . . . . January 2015. . . . . . . . . . 10
TRANSOM EDGE and ASTRAGALT-FMEA, T-FMA, DTA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . January 2015 . . . . . . . . . . 11
HEG . . . . . . . . . . . . . . . . . . . . . . . . . . . Hinge Edge Guards . . . . . . . . . . . . . . . . . . . . . . . . . . . . January 2015. . . . . . . . . . 12
HEG-M . . . . . . . . . . . . . . . . . . . . . . . . . Mid-Height Hinge Edge Guards . . . . . . . . . . . . . . . . . . . January 2015. . . . . . . . . . 13
LEG . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lock Edge Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . January 2015. . . . . . . . . . 14
MISCELLANEOUS DOOR PRODUCTSLBC . . . . . . . . . . . . . . . . . . . . . . . . . . . . Latch Bolt Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . January 2015. . . . . . . . . . 15
VRC. . . . . . . . . . . . . . . . . . . . . . . . . . . . Vertical rod Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . January 2015. . . . . . . . . . 16
January 2015EDGES anD aSTraGaLS InDEX PaGE a
3/32 (2.38mm) WEB MAY BE CUT OUT
Cylindrical Lock(with T-Strike)
161 SeriesMortise Lock(with ASA Strike)
86 Series ASA StrikeT-StrikeFlush BoltAutomatic
Flush BoltStandard
(KEY SIDE IS OUTSIDE)
QUANTITY MODEL HEIGHT FINISH
(Astragal is on LOW side of Bevel) (Astragal is on HIGH side of Bevel)
3° Bevel 90° Square Corners
WIDTH X HEIGHT
6 3/4"(172mm)
1"(25mm)
8 1/2"(216mm) 2 1/4"
(57mm)
1 1/8"(29mm)
8"(203mm)
1 1/4"(32mm)
4 7/8"(124mm)
3/4"(19mm)
3 3/8"(86mm)
1 1/2"(38mm)
5/8"(16mm)
2 3/4"(70mm)
(Lip of strike will always be on high side of bevel.)
DE - Double Egress
(Fill in appropriate dimensions)
(Specify one model and prep)
WIDTH X HEIGHT CENTERLINE
INACTIVEACTIVE
INACTIVE
ACTIVEACTIVE
INACTIVE
ACTIVEINACTIVE
BOTTOM OF DOOR EDGE
DOOR EDGE
HEIGHTFINISHED
OF
CENTERLINEBOLT
FLUSH
CENTERLINESTRIKE
OR CENTERLINEBOLT
FLUSH
SPECIFY DOOR THICKNESS
TOP OF DOOR EDGE
(INSIDE DIMENSION) SPECIFY SIDE OF DOOR WITH ASTRAGAL
LOCK
BOTTOM OF DOOR EDGE
HEIGHT
DOOR EDGE
FINISHEDCENTERLINE
OF
FLUSHBOLT
CENTERLINESTRIKE
LOCK
CENTERLINE
ORFLUSHBOLT
(INSIDE DIMENSION)SPECIFY DOOR THICKNESS
TOP OF DOOR EDGE
(INSIDE) (INSIDE) (INSIDE) (INSIDE)
WIDTH X HEIGHT CENTERLINE
WIDTH X HEIGHT
1"(25mm)
5/8"(16mm) 1 1/8"
(29mm) 3/4"(19mm)
1 1/4"(32mm)
LOCK PREP
RIGHT HAND ACTIVERH LH
LEFT HAND ACTIVE LEFT HAND REVERSELHR RHR
RIGHT HAND REVERSE
STANDARD MACHINING SPECIFICATIONS
FLUSH BOLT PREP STRIKE PREP
ORDER MODEL & QUANTITY
FLUSH BOLT(S)
LOCK
NON-STANDARD CUTOUTS
SPECIAL STRIKE
DEADBOLT
ALL DIMENSIONS SHOWN ARE CUTOUT SIZESDRAWING BELOW SHOULD REFLECT HANDING CHOICE ABOVE (i.e. Astragal on right side above, also on right side below)
ACTIVE ACTIVE
®
ACTIVE (INSWING) HANDING INFORMATION REVERSE ACTIVE (OUTSWING)
HARDWARE PREPARATIONDoor EDGES & aSTraGaLS
CuSToMEr
CITy P.o. nuMBEr
JoB naME
E-MaIL aDDrESS
orDEr MuST BE SIGnED
A MESTEK COMPANY
®
DOOR PRODUCTS
January 2015 PaGE B
90° 90°
90°90°
87°
93° 93°
87°
1"(25mm)
1 3/4"(44mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1 3/4"(44mm)
1 3/4"(44mm)
1 3/4"(44mm)
SQUARE EDGES
3° BEVELED EDGES
NOTE: For Exterior use, High Humidity or Salt Air application,product must be Galvanized or Stainless Steel.
IMPORTANT: Interpretation of building and fire codes may vary.Consult with the local authority having jurisdiction inyour area, to determine appropriate standards.
MATERIAL: 20 GA. (1mm) Cold Rolled Steel - Edges.
FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: Fits over edge of door (stile) and installs using
#6X3/4" phillips head sheet metal screws withcountersunk mounting holes for a flush
DOOR THICKNESS: For 1 3/4" (44mm) Doors.
MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized CoilStainless Steel Astragals have hemmed edge - see diagram
FINISH: Custom Baked Enamel colors (as per sample chip supplied). Plated finishes to match the vision frame, lock,hinges and closer.
FASTENERS: Special Security Screw Fasteners, See Security ProductsSection Page 27.
SPECIALS: Machining Preps (must have signed Hardware Prep Sheetattached with order).Lead Lined for X-ray applications - see page 10Door thickness (specify inside dimension required).
20/45/60/90 MINUTE: Approved Listing.
appearance on maximum 12" (305mm) centers.(spacing will vary based on hardware preparationand size)
18 GA. (1.25mm) Cold Rolled Steel - Astragals.
Anemostat manufacturing dimensions ±1/32Actual dimensions are nominal and may varybased on component manufacturers tolerances.
DETAIL DRAWING
®
TECHnICaL DaTaFroM
A MESTEK COMPANYP.o. BoX 4938 • 1220 WaTSonCEnTEr roaD
CarSon, Ca 90745-4206(310) 835-7500 • FaX (310) 835-0448
e-mail: [email protected] • website: www.anemostat.com
®
DOOR PRODUCTS
FMEAMETaL EDGES & aSTraGaL
(PaIr/SET)
STANDARD PRODUCT FEATURES OPTIONAL FEATURES
FIRE RATINGS (w/ U.L. & W.H.I. classification markings) Positive Pressure
January 2015EDGES anD aSTraGaLS PaGE 1
unDErWrITErS’LaBoraTorIES
WarnoCK HErSEy
FIrEraTInGS
Job name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .com
ASTRAGAL WITH HEMMED EDGE TO ELIMINATE SHARP EDGES.STAINLESS STEEL ONLY.
Job name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .com
WarnoCK HErSEy
January 2015EDGES anD aSTraGaLS PaGE 2
90° 90°
90°90°
87°
93° 93°
87°
93°
87° 93°
87°
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1 3/4"(44mm)
1 3/4"(44mm)
1 3/4"(44mm)
1 3/4"(44mm)
SQUARE EDGES
3° BEVELED EDGES
DOUBLE EGRESS (DE)
NOTE: Product is designed for Interior Use.
IMPORTANT: Interpretation of building and fire codes may vary.Consult with the local authority having jurisdiction inyour area, to determine appropriate standards.
MATERIAL: 20 GA. (1mm) Cold Rolled Steel - Edges.
FINISH: Ready to Stain, Seal and Finish.
INSTALLATION: Fits over edge of door (stile) and installs using#6X3/4 phillips flat head sheet metal screws withcountersunk mounting holes for a flush appearance.
DOOR THICKNESS: For 1 3/4" (44mm) Doors.
FASTENERS: Special Security Screw Fasteners, See Security ProductsSection, Page 27.
SPECIALS: Machining Preps (must have signed hardware Prep Sheetattached with order).Door thickness (specify inside dimension required).
20/45/60/90 MINUTE: Approved Listing.
18 GA. (1.25mm) Cold Rolled Steel - Astragals.Both Edges & Astragals have real wood veneerlaminated to the metal.
Hole spacing will vary, based on hardware preparation with maximum 12" (305mm) centers.
SPECIES: Available in most common wood species thatare compatible w/domestic wood door manufacturers.Not available in special veneer cut or sliced pattern.(Stocked in Red Oak, Natural Birch & African Khaya) SPECIES: Available in most common wood species that
are compatible w/domestic wood door manufacturers.
1"(25mm)
1 3/4"(44mm)
1"(25mm)
1"(25mm)
1 3/4"(44mm)
Anemostat manufacturing dimensions ±1/32Actual dimensions are nominal and may varybased on component manufacturers tolerances.
®
TECHnICaL DaTaFroM
DETAIL DRAWING
A MESTEK COMPANYP.o. BoX 4938 • 1220 WaTSonCEnTEr roaD
CarSon, Ca 90745-4206(310) 835-7500 • FaX (310) 835-0448
e-mail: [email protected] • website: www.anemostat.com
®
DOOR PRODUCTS
WV-FMEAWooD VEnEEr oVEr METaL
EDGES & aSTraGaLS(PaIr/SET)
STANDARD PRODUCT FEATURES
OPTIONAL FEATURES
FIRE RATINGS (W.H.I. classification markings) Positive Pressure
FIrE raTEDBy
90° 90°
90°90°
87°
93° 93°
87°
SQUARE EDGES
3° BEVELED EDGES
NOTE: For Exterior use, High Humidity or Salt Air application,product must be Galvanized or Stainless Steel.
IMPORTANT: Interpretation of building and fire codes may vary.Consult with the local authority having jurisdiction inyour area, to determine appropriate standards.
MATERIAL: 20 GA. (1mm) Cold Rolled Steel.FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: Fits over edge of door (stile) and installs using
#6X3/4" phillips head sheet metal screws withcountersunk mounting holes for a flush
DOOR THICKNESS: For 1 3/4" (44mm) Doors.
MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized CoilFINISH: Custom Baked Enamel colors (as per sample chip supplied).
Plated finishes to match the vision frame, lock,hinges and closer.
FASTENERS: Special Security Screw Fasteners, See Security ProductsSection Page 27.
SPECIALS: Machining Preps (must have signed Hardware Prep Sheetattached with order).Lead Lined for X-ray applications - see page 10.Door thickness (specify inside dimension required).
20/45/60/90 MINUTE: Approved Listing.
appearance on maximum 12" (305mm) centers.(spacing will vary based on hardware preparationand size)
1"(25mm)
1 3/4"(44mm)
1 3/4"(44mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
Anemostat manufacturing dimensions ±1/32Actual dimensions are nominal and may varybased on component manufacturers tolerances.
DETAIL DRAWING
®
TECHnICaL DaTaFroM
A MESTEK COMPANYP.o. BoX 4938 • 1220 WaTSonCEnTEr roaD
CarSon, Ca 90745-4206(310) 835-7500 • FaX (310) 835-0448
e-mail: [email protected] • website: www.anemostat.com
®
DOOR PRODUCTS
FMEMETaL EDGES
(PaIr/SET)
STANDARD PRODUCT FEATURES OPTIONAL FEATURES
FIRE RATINGS (w/ U.L. & W.H.I. classification markings) Positive Pressure
January 2015EDGES anD aSTraGaLS PaGE 3
unDErWrITErS’LaBoraTorIES
WarnoCK HErSEy
FIrEraTInGS
Job name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .com
Job name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .comJanuary 2015
EDGES anD aSTraGaLS PaGE 4
SQUARE EDGES
3° BEVELED EDGES
DOUBLE EGRESS (DE)
IMPORTANT: Interpretation of building and fire codes may vary.Consult with the local authority having jurisdiction inyour area, to determine appropriate standards.
MATERIAL: 20 GA (1mm) Cold Rolled Steel. Both Edges have real
FINISH: Ready to Stain, Seal and Finish.
INSTALLATION: Fits over edge of door (stile) and installs using#6X3/4 phillips flat head sheet metal screws withcountersunk mounting holes for a flush appearance.
DOOR THICKNESS: For 1 3/4" (44mm) Doors.
FASTENERS: Special Security Screw Fasteners, See Security ProductsSection, Page 27.
SPECIALS: Machining Preps (must have signed Hardware Prep Sheetattached with order).Door thickness (specify inside dimension required).
20/45/60/90 MINUTE: Approved Listing.
90° 90°
90°90°
87°
93° 93°
87°
93°
87° 93°
87°
wood veneer laminated to the metal.SPECIES: Available in most common wood species that are
compatible w/domestic wood door manufacturers.Not available in special veneer cut or sliced patterns.Veneer is stocked in Red Oak, Natural Birch & African Khaya however normal manufacturing lead times apply.
SPECIES: Available in most common wood species that arecompatible w/domestic wood door manufacturers.
Hole spacing will vary, based on hardwarepreparation with maximum 12" (305mm) centers.
NOTE: Product is designed for interior Use.
1"(25mm)
1 3/4"(44mm)
1 3/4"(44mm)
1 3/4"(44mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
Anemostat manufacturing dimensions ±1/32Actual dimensions are nominal and may varybased on component manufacturers tolerances.
®
TECHnICaL DaTaFroM
DETAIL DRAWING
A MESTEK COMPANYP.o. BoX 4938 • 1220 WaTSonCEnTEr roaD
CarSon, Ca 90745-4206(310) 835-7500 • FaX (310) 835-0448
e-mail: [email protected] • website: www.anemostat.com
®
DOOR PRODUCTS
WV-FMEWooD VEnEEr oVEr
METaL EDGES(PaIr)
STANDARD PRODUCT FEATURES
OPTIONAL FEATURES
FIRE RATINGS (with W.H.I. classification markings) Positive Pressure
WarnoCK HErSEy
FIrE raTEDBy
Job name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .com
unDErWrITErS’LaBoraTorIES
WarnoCK HErSEy
FIrEraTInGS
January 2015EDGES anD aSTraGaLS PaGE 5
3°
90°
90°
87°
93°
SQUARE EDGE
3° BEVELED EDGE
20/45/60/90 MINUTE: Approved Listing.NOTE: For Exterior use, High Humidity or Salt Air application,
product must be Galvanized or Stainless Steel.
MATERIAL: 20 GA. (1mm) Cold Rolled Steel - Edge.18 GA. (1.25mm) Cold Rolled Steel - Astragal.
FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: Fits over edge of door (stile) and installs using
#6X3/4 phillips head sheet metal screws withcountersunk mounting holes for a flush
DOOR THICKNESS: For 1 3/4" (44mm) Doors.
MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized CoilStainless Steel Astragals have hemmed edge - see diagram
FINISH: Custom Baked Enamel colors (as per sample chip supplied). Plated finishes to match the vision frame, lock,hinges and closer.
FASTENERS: Special Security Screw Fasteners, See Security ProductsSection Page 27.
SPECIALS: Machining Preps (must have signed Hardware Prep Sheetattached with order).Lead Lined for X-ray applications - see page 10Door thickness (specify inside dimension required).
appearance on maximum 12" (305mm) centers.(spacing will vary based on hardware preparationand size)
IMPORTANT: Interpretation of building and fire codes may vary.Consult with the local authority having jurisdiction inyour area, to determine appropriate standards.
1"(25mm)
1 3/4"(44mm)
1"(25mm)
1 3/4"(44mm)
1"(25mm)
1 3/4"(44mm)
1"(25mm)
1 3/4"(44mm)
Anemostat manufacturing dimensions ±1/32Actual dimensions are nominal and may varybased on component manufacturers tolerances.
®
TECHnICaL DaTaFroM
DETAIL DRAWING
A MESTEK COMPANYP.o. BoX 4938 • 1220 WaTSonCEnTEr roaD
CarSon, Ca 90745-4206(310) 835-7500 • FaX (310) 835-0448
e-mail: [email protected] • website: www.anemostat.com
®
DOOR PRODUCTS
FMAMETaL aSTraGaL
(EaCH)
STANDARD PRODUCT FEATURES OPTIONAL FEATURES
FIRE RATINGS (w/ U.L. & W.H.I. classification markings) Positive Pressure
ASTRAGAL WITH HEMMED EDGE TO ELIMINATE SHARP EDGES.STAINLESS STEEL ONLY.
Job name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .comJanuary 2015
EDGES anD aSTraGaLS PaGE 6
1 3/4"(44mm)
NOTE: For Exterior use, High Humidity or Salt Air application,product must be Galvanized or Stainless Steel.
MATERIAL: 10 GA. (3.4mm) Cold Rolled Steel.FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: Fits on edge of door (stile) and installs using
DOOR THICKNESS: For 1 3/4" (44mm) Doors.
MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized CoilFINISH: Custom Baked Enamel colors (as per sample chip supplied).
Plated finishes to match the vision frame, lock,hinges and closer.
FASTENERS: Special Security Screw Fasteners, See Security ProductsSection Page 27.
SPECIALS: Door Thickness.
FBA is not fire rated.
#6X32 phillips head steel thru bolts with a blankhead one side, and countersunk mounting holes on
STEEL BARROUND EDGE
1/8" X 2"(3mm) X (51mm)
2"(51mm)
1/2"(13mm)
12" (305mm) max. centers (spacing will vary based on hardware preparation and size) giving a flushappearance.
THRU-BOLT
IMPORTANT: Interpretation of building and fire codes may vary.Consult with the local authority having jurisdiction inyour area, to determine appropriate standards.
Anemostat manufacturing dimensions ±1/32Actual dimensions are nominal and may varybased on component manufacturers tolerances.
®
TECHnICaL DaTaFroM
DETAIL DRAWING
A MESTEK COMPANYP.o. BoX 4938 • 1220 WaTSonCEnTEr roaD
CarSon, Ca 90745-4206(310) 835-7500 • FaX (310) 835-0448
e-mail: [email protected] • website: www.anemostat.com
®
DOOR PRODUCTS
FBAFLaT METaL aSTraGaL
WITH THru BoLTS
STANDARD PRODUCT FEATURES OPTIONAL FEATURES
FIRE RATINGS (w/ U.L. & W.H.I. classification markings) Positive Pressure
noT FIrE raTED
87°
93°87°
93°
1"(25mm)
1 3/4"(44mm)
1"(25mm)
1"(25mm)
1"(25mm)
1 3/4"(44mm)
NOTE: For Exterior use, High Humidity or Salt Air application,product must be Galvanized or Stainless Steel.
IMPORTANT: Interpretation of building and fire codes may vary.Consult with the local authority having jurisdiction inyour area, to determine appropriate standards.
MATERIAL: 20 GA. (1mm) Cold Rolled Steel - Edges.18 GA. (1.25mm) Cold Rolled Steel - Astragals.
FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: Fits over edge of door (stile) and installs using
#6X3/4 phillips head sheet metal screws withcountersunk mounting holes for a flush
DOOR THICKNESS: For 1 3/4" (44mm) Doors.
MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized CoilFINISH: Custom Baked Enamel colors (as per sample chip supplied).
Plated finishes to match the vision frame, lock,hinges and closer.
FASTENERS: Special Security Screw Fasteners, See Security ProductsSection Page 27.
SPECIALS: Machining Preps (must have signed Hardware Prep Sheetattached with order).Lead Lined for X-ray applications - see page 10.Door thickness (specify inside dimension required).
20/45/60/90 MINUTE: Approved Listing.
appearance on maximum 12" (305mm) centers.(spacing will vary based on hardware preparationand size).
Anemostat manufacturing dimensions ±1/32Actual dimensions are nominal and may varybased on component manufacturers tolerances.
DETAIL DRAWING
®
TECHnICaL DaTaFroM
A MESTEK COMPANYP.o. BoX 4938 • 1220 WaTSonCEnTEr roaD
CarSon, Ca 90745-4206(310) 835-7500 • FaX (310) 835-0448
e-mail: [email protected] • website: www.anemostat.com
®
DOOR PRODUCTS
DE-FMEADouBLE EGrESS
METaL EDGE & aSTraGaL(PaIr/SET)
STANDARD PRODUCT FEATURES OPTIONAL FEATURES
FIRE RATINGS (w/ U.L. & W.H.I. classification markings) Positive Pressure
January 2015EDGES anD aSTraGaLS PaGE 7
unDErWrITErS’LaBoraTorIES
WarnoCK HErSEy
FIrEraTInGS
Job name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .com
ASTRAGAL WITH HEMMED EDGE TO ELIMINATE SHARP EDGES.STAINLESS STEEL ONLY.
1"(25mm)
1 3/4"(44mm)
1"(25mm)
1"(25mm)
1"(25mm)
NOTE: For Exterior use, High Humidity or Salt Air application,product must be Galvanized or Stainless Steel.
IMPORTANT: Interpretation of building and fire codes may vary.Consult with the local authority having jurisdiction inyour area, to determine appropriate standards.
MATERIAL: 20 GA. (1mm) Cold Rolled Steel.FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: Fits over edge of door (stile) and installs using
#6X3/4 phillips head sheet metal screws withcountersunk mounting holes for a flush
DOOR THICKNESS: For 1 3/4" (44mm) Doors.
MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized CoilFINISH: Custom Baked Enamel colors (as per sample chip supplied).
Plated finishes to match the vision frame, lock,hinges and closer.
FASTENERS: Special Security Screw Fasteners, See Security ProductsSection Page 27.
SPECIALS: Machining Preps (must have signed Hardware Prep Sheetattached with order).Door thickness (specify inside dimension required).
20/45/60/90 MINUTE: Approved Listing.
87°
93°87°
93°
appearance on maximum 12" (305mm) centers.(spacing will vary based on hardware preparationand size).
Anemostat manufacturing dimensions ±1/32Actual dimensions are nominal and may varybased on component manufacturers tolerances.
DETAIL DRAWING
®
TECHnICaL DaTaFroM
A MESTEK COMPANYP.o. BoX 4938 • 1220 WaTSonCEnTEr roaD
CarSon, Ca 90745-4206(310) 835-7500 • FaX (310) 835-0448
e-mail: [email protected] • website: www.anemostat.com
®
DOOR PRODUCTS
DE-FMEDouBLE EGrESS
METaL EDGES(PaIr/SET)
STANDARD PRODUCT FEATURES OPTIONAL FEATURES
FIRE RATINGS (w/ U.L. & W.H.I. classification markings) Positive Pressure
January 2015EDGES anD aSTraGaLS PaGE 8
unDErWrITErS’LaBoraTorIES
WarnoCK HErSEy
FIrEraTInGS
Job name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .com
Job name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .com
unDErWrITErS’LaBoraTorIES
WarnoCK HErSEy
FIrEraTInGS
January 2015EDGES anD aSTraGaLS PaGE 9
87°
93°
IMPORTANT: Interpretation of building and fire codes may vary.Consult with the local authority having jurisdiction inyour area, to determine appropriate standards.
NOTE: For Exterior use, High Humidity or Salt Air application,product must be Galvanized or Stainless Steel.
MATERIAL: 20 GA. (1mm) Cold Rolled Steel - Edge.18 GA. (1.25mm) Cold Rolled Steel - Astragal.
FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: Fits over edge of door (stile) and installs using
#6X3/4 phillips head sheet metal screws withcountersunk mounting holes for a flush
DOOR THICKNESS: For 1 3/4" (44mm) Doors.
MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized CoilFINISH: Custom Baked Enamel colors (as per sample chip supplied).
Plated finishes to match the vision frame, lock,hinges and closer.
FASTENERS: Special Security Screw Fasteners, See Security ProductsSection Page 27.
SPECIALS: Machining Preps (must have signed Hardware Prep Sheetattached with order).Lead Lined for X-ray applications - see page 10Door thickness (specify inside dimension required).
appearance on maximum 12" (305mm) centers.(spacing will vary based on hardwarepreparation and size).
1"(25mm)
1 3/4"(44mm)
1"(25mm)
1 3/4"(44mm)
20/45/60/90 MINUTE: Approved Listing.
Anemostat manufacturing dimensions ±1/32Actual dimensions are nominal and may varybased on component manufacturers tolerances.
®
TECHnICaL DaTaFroM
DETAIL DRAWING
A MESTEK COMPANYP.o. BoX 4938 • 1220 WaTSonCEnTEr roaD
CarSon, Ca 90745-4206(310) 835-7500 • FaX (310) 835-0448
e-mail: [email protected] • website: www.anemostat.com
®
DOOR PRODUCTS
DE-FMADouBLE EGrESSMETaL aSTraGaL
(EaCH)
STANDARD PRODUCT FEATURES OPTIONAL FEATURES
FIRE RATINGS (w/ U.L. & W.H.I. classification markings) Positive Pressure
ASTRAGAL WITH HEMMED EDGE TO ELIMINATE SHARP EDGES.STAINLESS STEEL ONLY.
3° BEVELED EDGES
SQUARE EDGES
EXPLODED VIEW
CAP LE
AD LI
NING ASTR
AGAL
87°
93°93°
87°
90° 90°
90°90°
ASTRAGAL
LEAD LINING(1/16" THICK) (1.6mm)
or(1/8" THICK) (3mm)
CAP
LEAD DENSITY = 4 LBS./SQF
HOLE SPACING 9"-12" (229-305mm)
BASED ON HEIGHT
DETAIL DRAWING
®
TECHnICaL DaTaFroM
A MESTEK COMPANYP.o. BoX 4938 • 1220 WaTSonCEnTEr roaD
CarSon, Ca 90745-4206(310) 835-7500 • FaX (310) 835-0448
e-mail: [email protected] • website: www.anemostat.com
®
DOOR PRODUCTS
FMEALEAD LINED
METaL EDGES & aSTraGaL(PaIr/SET)
January 2015EDGES anD aSTraGaLS PaGE 10
noT FIrE raTED
Job name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .com
For Complete Technical Datasee this section• FMA • FMEA• DE-FMA • DE-FMEA
Job name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .comJanuary 2015
EDGES anD aSTraGaLS PaGE 11
90° 90°
90°90°
90°90° 90°
T-FMEA T-FMA DTA
NOTE: For Exterior use, High Humidity or Salt Air application,product must be Galvanized or Stainless Steel.
MATERIAL: 20 GA. (1mm) Cold Rolled Steel - Edges.18 GA. (1.25mm) Cold Rolled Steel - Astragals.
FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: Fits over top edge of door (top rail) and installs
using #6X3/4 phillips head sheet metal screwswith countersunk mounting holes for a flush
DOOR THICKNESS: For 1 3/4" (44mm) Doors.
MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized CoilFINISH: Custom Baked Enamel colors (as per sample chip supplied).
Plated finishes to match the vision frame, lock,hinges and closer.
FASTENERS: Special Security Screw Fasteners, See Security ProductsSection Page 27.
SPECIALS: Machining Preps (must have signed Hardware Prep Sheetattached with order).Lead Lined for X-ray applications - see page 10.Door thickness (specify inside dimension required).
T-FMEA, T-FMA, DTA are not fire rated.
DOOR
TRANSOM TRANSOM
DOOR
TRANSOM
DOOR
appearance on maximum 12" (305mm) centers.(spacing will vary based on hardware preparationand size)
IMPORTANT: Interpretation of building and fire codes may vary.Consult with the local authority having jurisdiction inyour area, to determine appropriate standards.
1"(25mm)
1 3/4"(44mm)
1"(25mm)
1"(25mm)
1"(25mm)
1 3/4"(44mm)
1 3/4"(44mm)
1"(25mm)
1 3/4"(44mm)
1"(25mm)
1 3/4"(44mm)
1"(25mm)
1 3/4"(44mm)
Anemostat manufacturing dimensions ±1/32Actual dimensions are nominal and may varybased on component manufacturers tolerances.
®
TECHnICaL DaTaFroM
DETAIL DRAWING
A MESTEK COMPANYP.o. BoX 4938 • 1220 WaTSonCEnTEr roaD
CarSon, Ca 90745-4206(310) 835-7500 • FaX (310) 835-0448
e-mail: [email protected] • website: www.anemostat.com
®
DOOR PRODUCTS
T-FMEATranSoM EDGE & aSTraGaL
(PaIr/SET)T-FMA
TranSoM aSTraGaL(EaCH)DTA
TranSoM aSTraGaL(EaCH)
STANDARD PRODUCT FEATURES OPTIONAL FEATURES
FIRE RATINGS (w/ U.L. & W.H.I. classification markings) Positive Pressure
noT FIrE raTED
HINGE SPECS
5/8" (16mm)(face) X 7/8" (23mm)(edge) - Standard3° BEVEL (STANDARD)
RIGHT HANDLEFT HAND
90° SQUARE 90° SQUARE3° BEVEL (STANDARD)5/8" (16mm)(face) X 7/8" (23mm)(edge) - Standard
Door Thickness - Specify - SpecifyDoor Thickness(face) X X (face) - Specify (edge)
NOTE: For Exterior use, High Humidity or Salt Air application,product must be Galvanized or Stainless Steel.
MATERIAL & FINISH: 18 GA. (1.25mm) #304 Stainless Steel, #4 Finish (Satin).INSTALLATION: Fits over hinge edge (stile) of door and installs
using #6X3/4 stainless steel phillips head sheet metal screws with countersunk mounting holes for a flush appearance.
DOOR THICKNESS: For 1 3/4" (44mm) Doors with 1/4" (6mm) hinge back set
MATERIAL: #316 Stainless Steel, Cold Rolled Steel or Galvanized Coil.FINISH: Custom Baked Enamel colors (as per sample chip supplied).
Plated finishes to match the vision frame, lock, hinges and closer.FASTENERS: Special Security Screw Fasteners, See Security Products
Section Page 27.
20/45/60/90 MINUTE: Approved Listing
SPECIALS: Hinge machining preps (must have signed Hinge PrepSheet attached with order)Door thickness (specify hinge backset required).
TOP OF DOOR
TOP OF HINGE
HINGE SIZE
TOP OF HINGE
TOP OF HINGE
DOOR
HEIGHTFINISHED
Special overall dimension other than 5/8" (16mm) x 7/8" (23mm).
1/4" (6mm) IS STANDARD
HINGE BACKSETHINGE BACKSET
1/4" (6mm) IS STANDARDFINISHED
HEIGHT
DOOR
TOP OF HINGE
TOP OF HINGE
HINGE SIZE
TOP OF HINGE
TOP OF DOOR
PUSH SIDEOF DOOR
QUANTITY QUANTITY
HINGE SIZE: 4" (102mm), 4 1/2" (114mm) and 5" (127mm) are standard.Other sizes require a special setup.
IMPORTANT: Interpretation of building and fire codes may vary.Consult with the local authority having jurisdiction inyour area, to determine appropriate standards.
HINGE EDGE
1 3/4"(44mm)
7/8"(16mm)
93°
5/8"(22mm)
HINGE EDGE
93°
1 3/4"(44mm)
7/8"(16mm)
5/8"(22mm)
(face) X X (face) - Specify (edge)
DETAIL DRAWING
®
TECHnICaL DaTaFroM
A MESTEK COMPANYP.o. BoX 4938 • 1220 WaTSonCEnTEr roaD
CarSon, Ca 90745-4206(310) 835-7500 • FaX (310) 835-0448
e-mail: [email protected] • website: www.anemostat.com
®
DOOR PRODUCTS
HEGHInGE EDGE GuarD
(EaCH)FuLL HEIGHT
STANDARD PRODUCT FEATURES OPTIONAL FEATURES
FIRE RATINGS (w/ U.L. & W.H.I. classification markings) Positive Pressure
January 2015EDGES anD aSTraGaLS PaGE 12
unDErWrITErS’LaBoraTorIES
WarnoCK HErSEy
FIrEraTInGS
Job name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .com
HINGE SPECS RIGHT HANDLEFT HAND
MID HEIGHTHEG
HEIGHTOVERALLHEIGHT
OVERALL
TOP OF HINGE
HINGE SIZE
FINISHEDHEIGHT
(SPECIFY DIMENSIONS)
PUSH SIDEOF DOOR
QUANTITY QUANTITY
TOP OF HINGEHINGE SIZE
HINGE EDGE
1 3/4"(44mm)
7/8"(16mm)
93°
5/8"(22mm)
93°
HINGE EDGE
Other sizes require a special setup.
DOOR THICKNESS: For 1 3/4" (44mm) Doors with 1/4" (6mm) hinge back set
INSTALLATION: Fits over hinge edge (stile) of door and installs using #6X3/4" stainless steel phillips head sheet metal screws with countersunk mounting holes for a flush appearance.
MATERIAL & FINISH: 18 GA. (1.25mm) #304 Stainless Steel, #4 Finish (Satin).
product must be Galvanized or Stainless Steel.NOTE: For Exterior use, High Humidity or Salt Air application,
Door thickness (specify hinge backset required).
SPECIALS: Hinge machining preps (must have signed Hinge Prep
FASTENERS: Special Security Screw Fasteners, See Security ProductsPlated finishes to match the vision frame, lock, hinges and closer.
FINISH: Custom Baked Enamel colors (as per sample chip supplied). MATERIAL: #316 Stainless Steel, Cold Rolled Steel or Galvanized Coil.
Sheet attached with order)
Section Page 27.
BOTTOM OF HINGE BOTTOM OF HINGE
1 3/4"(44mm)
7/8"(16mm)
5/8"(22mm)
20/45/60/90 MINUTE: Approved Listing
IMPORTANT: Interpretation of building and fire codes may vary.Consult with the local authority having jurisdiction inyour area, to determine appropriate standards.
1/4" (6mm) IS STANDARD
HINGE BACKSETHINGE BACKSET
1/4" (6mm) IS STANDARD
HINGE SIZE: 4" (102mm), 4 1/2" (114mm) and 5" (127mm) are standard.
Special overall dimension other than 5/8" (16mm) x 7/8" (23mm).
5/8" (16mm)(face) X 7/8" (23mm)(edge) - Standard3° BEVEL (STANDARD) 90° SQUARE
Door Thickness - Specify(face) X X (face) - Specify (edge)
5/8" (16mm)(face) X 7/8" (23mm)(edge) - Standard3° BEVEL (STANDARD) 90° SQUARE
Door Thickness - Specify(face) X X (face) - Specify (edge)
DETAIL DRAWING
®
TECHnICaL DaTaFroM
A MESTEK COMPANYP.o. BoX 4938 • 1220 WaTSonCEnTEr roaD
CarSon, Ca 90745-4206(310) 835-7500 • FaX (310) 835-0448
e-mail: [email protected] • website: www.anemostat.com
®
DOOR PRODUCTS
HEG-MHInGE EDGE GuarD
(EaCH)MID HEIGHT
STANDARD PRODUCT FEATURES OPTIONAL FEATURES
FIRE RATINGS (w/ U.L. & W.H.I. classification markings) Positive Pressure
January 2015EDGES anD aSTraGaLS PaGE 13
unDErWrITErS’LaBoraTorIES
WarnoCK HErSEy
FIrEraTInGS
Job name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .com
90° 90°
90°90°
87°
93° 93°
87°
SQUARE EDGES
3° BEVELED EDGES
1"(25mm)
1 3/4"(44mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1"(25mm)
1 3/4"(44mm)
Anemostat manufacturing dimensions ±1/32Actual dimensions are nominal and may varybased on component manufacturers tolerances.
DETAIL DRAWING
®
TECHnICaL DaTaFroM
A MESTEK COMPANYP.o. BoX 4938 • 1220 WaTSonCEnTEr roaD
CarSon, Ca 90745-4206(310) 835-7500 • FaX (310) 835-0448
e-mail: [email protected] • website: www.anemostat.com
®
DOOR PRODUCTS
LEGLoCK EDGE GuarD
(EaCH)
STANDARD PRODUCT FEATURES OPTIONAL FEATURES
FIRE RATINGS (w/ U.L. & W.H.I. classification markings) Positive Pressure
January 2015EDGES anD aSTraGaLS PaGE 14
unDErWrITErS’LaBoraTorIES
WarnoCK HErSEy
FIrEraTInGS
Job name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .com
■ MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized Coil.■ FINISH: Custom Baked Enamel colors (as per sample chip supplied).
Plated finishes to match the vision frame, lock, hinges and closer.■ FASTENERS: Special Security Screw Fasteners, see Security Products
Section, page 27.■ SPECIALS: Matching Preps (must have signed Hardware
Prep Sheet attached with order).Door Thickness (specify inside dimension required)
■ 20/45/60/90 MINUTE: approved Listing
■ MATERIAL: 20 Ga. (1mm) Cold rolled Steel■ FINISH: Grey Primer, Beige or Bronze Baked Enamel■ INSTALLATION: Fits over the edge of door (stile) and installs using
#6X3/4” phillips head sheet metal screws withcountersunk mounting holes for a flush appearanceon maximum 12" (305mm) centers. (spacing willvary based on hardware preparation and size)
■ DOOR THICKNESS: For 1 3/4" (44mm) Doors.■ NOTE: For Exterior use, High Humidity or Salt air application,
Product must be Galvanized or Stainless Steel.■ IMPORTANT: Interpretation of building and fire codes may vary.
Consult with the local authority having jurisdiction inyour area, to determine appropriate standards.
January 2015EDGES anD aSTraGaLS PaGE 15
Job name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .com
WarnoCK HErSEy
FIrE raTEDBy
LATCH BOLT COVER ONLY10" (254mm) OVERALL HEIGHT
FROM DOOR2 1/8" (29mm) PROJECTION
IMPORTANT: Interpretation of building and fire codes may vary.Consult with the local authority having jurisdiction in
can be used with the Vertical Rod Covers (VRC - Coverscanes or walkers, and helps to avoid possible injury. Itprevent entanglement with wheel chair foot rests, crutches,California Title 24 and A.D.A. requirements. LBC's help
INSTALLATION: Installed with #6 x 3/4" flat head sheet metal screws directly into door. Mounted over the vertical rod latch bolt hardware to be protected.
USES: Latch Bolt Covers are used to aid in complying with
the lower latch bolt) to completely protect the assembly
FINISH: #4 SatinMATERIAL: 18 GA. (1.25mm) #304 Stainless Steel.
Consult the Factory for optional Fasteners.
20/45/60/90 MINUTE: Approved listings.
your area, to determine appropriate standards.
7" (178mm) OVERALLFINISHED WIDTH
FASTENERS: Special Security Screw Fasteners are available.
VERTICAL ROD
COVER (VRC)VERTICAL ROD
COVER (LBC)LATCH BOLT
DOOR
VERTICAL ROD
MATERIAL: 16 GA. (1.7mm) #304 or #316 Stainless Steel, #4 Finish (Satin),Custom heights available, consult factory.
HEIGHT: 10" (254mm) height is standard unless otherwise specified.
34" (864mm) off the floor.
LBC (Latch Bolt Cover) is usually sold withthe VRC (Vertical Rod Cover) see page 2, this section,and are primarily used on double door installations
Anemostat manufacturing dimensions ±1/32Actual dimensions are nominal and may varybased on component manufacturers tolerances.
®
TECHnICaL DaTaFroM
DETAIL DRAWING
A MESTEK COMPANYP.o. BoX 4938 • 1220 WaTSonCEnTEr roaD
CarSon, Ca 90745-4206(310) 835-7500 • FaX (310) 835-0448
e-mail: [email protected] • website: www.anemostat.com
®
DOOR PRODUCTS
LBCLaTCH BoLT
CoVEr
STANDARD PRODUCT FEATURES OPTIONAL FEATURES
FIRE RATINGS (W.H.I. classification markings) Positive Pressure
January 2015EDGES anD aSTraGaLS PaGE 16
Job name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .com
WarnoCK HErSEy
FIrE raTEDBy
It can be used with the Latch Bolt Covers (LBC - coverscanes or walkers, which could lead to possible injury.prevent entanglement with wheel chair foot rests, crutches,California Title 24 and A.D.A. requirements. VRC's help
INSTALLATION: Installed with #6 x 3/4" flat head stainless steel sheet metal screws directly into door. Mounted over the vertical rod hardware to be protected.
USES: Vertical Rod Covers are used to aid in complying with
MATERIAL: 18 GA. (1.25mm) #304 Stainless Steel.
the lower latch bolt) to completely protect the assembly
FINISH: #4 Satin
COVER (LBC)LATCH BOLT
COVER (VRC)VERTICAL ROD
VERTICAL ROD
DOOR
Consult the Factory for optional Fasteners.
FROM DOOR1 1/16" (27mm) PROJECTION
FASTENERS: Special Security Screw Fasteners are available.
MATERIAL: 16 GA. (1.7mm) #304 or #316 Stainless Steel, #4 Finish (Satin),
IMPORTANT: Interpretation of building and fire codes may vary.Consult with the local authority having jurisdiction inyour area, to determine appropriate standards.
20/45/60/90 MINUTE: Approved listings.
VERTICAL ROD
HEIGHT24" (610mm) OVERALL
3/4"(19mm)
3 1/8"(79mm)
HEIGHT: 24" (610mm) length is standard unless otherwise specified.Custom heights available, consult factory.
34" (864mm) off the floor.
and are primarily used on double door installationsthe LBC (Latch Bolt Cover) see page 1, this section,VRC (Vertical Rod Cover) is usually sold with
Anemostat manufacturing dimensions ±1/32Actual dimensions are nominal and may varybased on component manufacturers tolerances.
®
TECHnICaL DaTaFroM
DETAIL DRAWING
A MESTEK COMPANYP.o. BoX 4938 • 1220 WaTSonCEnTEr roaD
CarSon, Ca 90745-4206(310) 835-7500 • FaX (310) 835-0448
e-mail: [email protected] • website: www.anemostat.com
®
DOOR PRODUCTS
VRCVErTICaL roD
CoVEr
STANDARD PRODUCT FEATURES OPTIONAL FEATURES
FIRE RATINGS (with W.H.I. classification markings) Positive Pressure