dividers accessoires - niedax.de · available siderail heights 20 50 80 110 grp-cable tray,...
TRANSCRIPT
KK2Cable tray systems available in height 20 50 80 110
KSystemSystem
KKK²K²KCable trays
Dividers
Fittings
Covers
Accessoires
26
CABLE TRAY SYSTEM GFK
The cable tray system K² EBO Systems (hot press moulding) offers the widest and most complete
range of the GRP market. Its unique interlocking and self-adjusting couplers allows a screwless
connection between the cable tray lengths, and a support distance of up to 1.5 m.
Covers
Accessoires
27
Available siderail heights 20 50 80 110
GRP-Cable tray, pressed, perforated KKL 30 30 35 40
GRP-Cable tray, pressed, not perforated KK 30 30 35 40
GRP-Encap, pressed KKKE ––––– 30 35 40
GRP-Splice plate, pressed, horizontal KKGH ––––– 31 35 40
STAINLESS STEEL-Splice plate-horizontal KKIH ––––– 31 36 41
GRP-Divider, pressed KKT... ––––– 31 36 41
GRP-T, pressed, small radius KKSS ––––– 31 36 –––––
GRP-T, pressed, big radius KKST ––––– 31 36 41
GRP-Elbow 45°, pressed, horizontal KKC ––––– 32 37 41
GRP-Elbow 90°, pressed, big radius KKB ––––– 32 37 42
GRP-Elbow 90°, pressed, small radius KKW ––––– 32 37 41
GRP-Reducer, pressed, right KKRR ––––– 32 37 42
GRP-Reducer, pressed, left KKRL ––––– 32 38 42
GRP-Splice plate, vertical KKGV ––––– 33 38 42
STAINLESS STEEL-Splice plate, vertical KKIV ––––– 33 38 42
GRP-Changing elevation KKET ––––– 33 38 43
GRP-Inside elbow 90°, pressed KKBI ––––– 33 39 43
GRP-Outside elbow 90°, pressed KKBA ––––– 34 39 43
GRP-Mounting plate, pressed MP ––––– 34 39 44
Cover clip DF... 50/51
Separating stud TB 52*
Dome head bolt FKM 52*
Hexagon head bolt SKM 52*
Cover fi xing insert DF M 50*
Cover clip DFUB 52*
Covers for cables ladders UL systems are available from page 46.
* suitable for all heights
SYSTEM
ACCESSORIES
80 1105020
80 1105020
80 1105020
80 1105020
80 1105020
80 1105020
80 1105020
80 1105020
80 1105020
80 1105020
80 1105020
80 1105020
80 1105020
80 1105020
80 1105020
80 1105020
80 1105020
80 1105020
80 1105020
NEW
28
CABLE TRAY SYSTEM K²
KKST...
KK...
KKB...
KKSS...
KKRR...
KKET...
KKBI...
KKKE...
KKBA...
KKETD...
KKC...
KKETD...
KKD...
29
30
CABLE TRAY SYSTEM K²
GRP cable trayspressed, perforated, equipped with a shaped coupler
KKL 20.050
7032 20 50 3 830K23
Item ref. RAL colour
Height WidthB
Materialthickness
(th)
Operatingcross cut
mm mm mm mm²
Min. pack.
3 m
EANcode
952205
Weight 100 units
m
47
The splice plates KKGH must be fixed on the base.Due to the expansion of the material, the following points during installation must be observed:Please take into account an expansion joint of 8 mm for dilatation.For fixing the cables trays on brackets, you need to drill a 9 mm diameter hole for the fixing of thecable tray base with bolts M6x20 V4A .Warning: the deflection is measured with a junction position between 2 cable trays at a distance L/5from the support. If this distance is not respected, it is necessary to raise the deflection values byapprox. 30%.
GRP cable trayspressed, not perforated, with interlocking coupler,
KK 20.050
7032 20 50 3 830K23
Item ref. RAL colour
Height WidthB
Materialthickness
(th)
Operatingcross cut
mm mm mm mm²
Min. pack.
3 m
EANcode
952007
Weight 100 units
m
47
The splice plates KKGH must be fixed on the baseDue to the expansion of the material, the following points during installation must be observed :Please take into account an expansion joint of 8 mm for dilatation. For the fixing of cable trays onbrackets, a 9 mm diameter hole must be drilled in the cable tray base to fix them with bolts M6x20V4A.Warning : the deflection is measured with a junction position between 2 cable trays at a distance L/5from the support. If this distance is not respected, it is necessary to raise the deflection values byapprox. 30%.
GRP cable trayspressed, perforated, equipped with a shaped coupler
KKL 50.050
7032 50 50 0,05 3 1500KKL 50.100 7032 50 100 0,3 3 3700KKL 50.150 7032 50 150 0,3 3 5900KKL 50.200 7032 50 200 0,3 3 8100KKL 50.300 7032 50 300 0,3 3 12500
K23
K23K23K23K23
Item ref. RAL colour
Height WidthB
Admissible load
F at L=1,5 m
Materialthickness
(th)
Operatingcross cut
mm mm kN/m mm mm²
Min. pack.
3 m3 m3 m3 m3 m
EANcode
952212952229952236952243952250
Weight 100 units
m
66,494,6
128,0137,4210,0
Warning : the deflection is measured with a junction position between 2 cable trays at a distance L/5from the support. If this distance is not respected, it is necessary to raise the deflection values byapprox. 30%.
GRP cable trayspressed, not perforated, with interlocking coupler
KK 50.050
7032 50 50 0,05 3 1500KK 50.100 7032 50 100 0,3 3 3700KK 50.150 7032 50 150 0,3 3 5900KK 50.200 7032 50 200 0,3 3 8100KK 50.300 7032 50 300 0,3 3 12500
K23
K23K23K23K23
Item ref. RAL colour
Height WidthB
Admissible load
F at L=1,5 m
Materialthickness
(th)
Operatingcross cut
mm mm kN/m mm mm²
Min. pack.
3 m3 m3 m3 m3 m
EANcode
952014952021952038952045952052
Weight 100 units
m
7098
125152210
Warning : the deflection is measured with a junction position between 2 cable trays at a distance L/5from the support. If this distance is not respected, it is necessary to raise the deflection values byapprox. 30%.
End cap for GRP cable traypressed
for the closing of the cable tray ends
Used for: Cable trays KK…, KKL… H50 mm
Mounting accessories required : 2 bolts M6x16 V4A ( to be ordered separately )
KKKE 50.050
7032 50 50KKKE 50.100 7032 50 100KKKE 50.150 7032 50 150KKKE 50.200 7032 50 200KKKE 50.300 7032 50 300
K23
K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.
EANcode
955190955206955213955220955237
Weight 100 units
pc
2,06,04,0
11,517,0
31
GRP adjustable splice platepressed, horizontal
Need: 2 pieces for each cut
for the horizontal connection of cable trays and fittings H50 mm lengthwise
Mounting accessories required : 4 bolts M6x20 V4A ( to be ordered separately )
KKGH 50
7032 35K23
Item ref. RAL colour
Height
mm
Min. pack.
1 set
EANcode
955626
Weight 100 units
2,4
for the cable tray connection with an expansion joint
Horizontal splice platehorizontal
Need: 2 pieces for each cut
for the horizontal connection of cable trays and fittings H50 mm and for the changes of directions.
Mounting accessories required : 4 bolts M6x16 V4A ( to be ordered separately )
KKIH 50 E4
38E4
Item ref. Height
mm
Min. pack.
1 set
EANcode
955657
Weight 100 units
1,4
for the length adjustment, please leave a space between cable trays.
GRP separatorpressed
The divider KKT 50 is delivered not mounted, it can be fixed in the cable tray with a bolt M 6x16V4A each meter.The divider KKT50/M can be delivered pre-mounted ( riveted ), the position inside the cabletray must be defined in the purchase order.
to separate cables with different functions and / or to separate voltages
KKT 50
7032 42KKT 50/M 7032 42
K23
K23
Item ref. RAL colour
Height
mm
Min. pack.
3 m3 m
EANcode
953028953059
Weight 100 units
m
3838
GRP tee junction for cable tray, small radiuspressed, with interlocking coupler
KKSS 50.050
7032 50 50KKSS 50.100 7032 50 100KKSS 50.150 7032 50 150KKSS 50.200 7032 50 200KKSS 50.300 7032 50 300
K23
K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.
EANcode
954780954797954803954810954827
Weight 100 units
pc
1510202530
During the installation, you must take care to position a support at each cable tray end and to fix themwith bolts M 6x16 V4A.
GRP tee junction for cable tray, large radiuspressed, with interlocking coupler
KKST 50.100
7032 50 100KKST 50.150 7032 50 150KKST 50.200 7032 50 200KKST 50.300 7032 50 300
K23
K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.
EANcode
954575954582954599954605
Weight 100 units
pc
60,067,776,6
100,0
During the assembly, every fitting must be supported at each end, at the cable entry. To ensure a correct installation, the couplers must be fixed laterally by 4 bolts M6x16 V4A on eachtray end.
32
CABLE TRAY SYSTEM K²
Horizontal elbow 45°pressed, with interlocking coupler
The piece is provided with a sleeve riveted on one side only.
KKC 50.100
7032 50 100 100KKC 50.150 7032 50 150 175KKC 50.200 7032 50 200 200KKC 50.300 7032 50 300 225
K23
K23K23K23
Item ref. RAL colour
Height WidthB
Radius R
mm mm mm
Min. pack.
1 p.1 p.1 p.1 p.
EANcode
953400953417953424953431
Weight 100 units
pc
20253060
To ensure a correct installation, the couplers must be fixed laterally by 2 bolts M6x16 V4A on eachtray end.
Horizontal elbow 90°, small radiuspressed, with interlocking coupler
KKW 50.050
7032 50 50KKW 50.100 7032 50 100KKW 50.150 7032 50 150KKW 50.200 7032 50 200KKW 50.300 7032 50 300
K23
K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.
EANcode
953646953653953660953677953684
Weight 100 units
pc
1021354080
During the assembly, every fitting must be supported at each end, at the cable entry. To ensure a correct installation, the couplers must be fixed laterally by 2 bolts M6x16 V4A on eachtray end.
Horizontal elbow 90°, large radiuspressed, with interlocking coupler
KKB 50.100
7032 50 100 125 100KKB 50.150 7032 50 150 200 175KKB 50.200 7032 50 200 225 200KKB 50.300 7032 50 300 250 225
K23
K23K23K23
Item ref. RAL colour
Height WidthB
C Radius R
mm mm mm mm
Min. pack.
1 p.1 p.1 p.1 p.
EANcode
953165953172953189953196
Weight 100 units
pc
37,060,070,0
134,8
During the assembly, we recommend to support each end of fitting at each cable entry.To ensure a correct installation, the couplers must be fixed laterally by 2 bolts M6x16 V4A on eachtray end.
GRP right hand reductionpressed, with interlocking coupler
KKRR 50.200
7032 50 200KKRR 50.300 7032 50 300
K23
K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.
EANcode
955022955039
Weight 100 units
pc
90114
During the assembly, every reducer must be supported at each end.To ensure a correct installation, the couplers must be fixed laterally by 2 bolts M6x16 V4A on eachtray end.
GRP left hand reductionpressed, with interlocking coupler
KKRL 50.200
7032 50 200KKRL 50.300 7032 50 300
K23
K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.
EANcode
954919954926
Weight 100 units
pc
90114
During the assembly, every reducer must be supported at each end.To ensure a correct installation, the couplers must be fixed laterally by 2 bolts M6x16 V4A on eachtray end.
33
GRP vertical splice platepressed, horizontal
Need: 2 pieces for each cut
for the vertical connection of cable trays and fittings H50 with an angle adjustment.
Mounting accessories required : 4 bolts M6x20 V4A ( to be ordered separately )
KKGV 50
7032 35K23
Item ref. RAL colour
Height
mm
Min. pack.
1 set
EANcode
955138
Weight 100 units
5
Stainless steel vertical splice plate V4Avertical
Need: 2 pieces for each cut
for the horizontal connection of cable trays and fittings H50 mm and for the changes of directions.
Mounting accessories required : 4 bolts M6x16 V4A ( to be ordered separately )
KKIV 50 E4
38E4
Item ref. Height
mm
Min. pack.
1 set
EANcode
955169
Weight 100 units
3
GRP changing elevationpressed, with interlocking coupler
Composed with different pieces, the changing elevation can be mounted in different heights
KKET 50.100
7032 50 100 160 480 800KKET 50.150 7032 50 150 160 480 800KKET 50.200 7032 50 200 160 480 800KKET 50.300 7032 50 300 160 480 800
K23
K23K23K23
Item ref. RAL colour
Height WidthB
HeightH1
HeightH2
HeightH3
mm mm mm mm mm
Min. pack.
1 p.1 p.1 p.1 p.
EANcode
954339954346954353954360
Weight 100 units
pc
210216259263
During the assembly, every fitting must be supported at each end and in the fitting center. To ensure a correct installation, the couplers must be fixed laterally by 2 bolts M6x16 V4A on eachtray end.The part height depends on the height and the configuration usedH1 = 160 mm =>L1 = 785 mm ( a cut is necessary )H2 = 480 mm =>L2 = 1100 mmH3 = 800 mm =>L3 = 970 mm
GRP vertical inside elbowpressed, with interlocking coupler
KKBI 50.050
7032 50 50KKBI 50.100 7032 50 100KKBI 50.150 7032 50 150KKBI 50.200 7032 50 200KKBI 50.300 7032 50 300
K23
K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.
EANcode
954025954032954049954056954063
Weight 100 units
pc
11,737,561,077,090,9
During the assembly, we recommend to support each end of fitting at each cable entry.Mounting accessories required : 2 bolts M6x16 V4A ( to be ordered separately )
34
CABLE TRAY SYSTEM K²
GRP vertical outside elbowpressed, with interlocking coupler
KKBA 50.050
7032 50 50KKBA 50.100 7032 50 100KKBA 50.150 7032 50 150KKBA 50.200 7032 50 200KKBA 50.300 7032 50 300
K23
K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.
EANcode
953837953844953851953868953875
Weight 100 units
pc
11,532,034,951,074,0
During the assembly, we recommend to support each end of fitting at each cable entry.To ensure a correct installation, the couplers must be fixed laterally by 2 bolts M6x16 V4A on eachtray end.
Mounting platepressed, easy to install, with pre-mounted fixing clamps
The mounting plate is in GRP, only the mounting lug are in stainless steel V4A
for the installation of equipment or junction boxes
MP 50
7032 50E4 K23
Item ref. RAL colour
Height
mm
Min. pack.
1 p.
EANcode
963010
Weight 100 units
pc
17
35
GRP cable trayspressed, perforated, equipped with a shaped coupler, with reinforced sidewalls (5 mm)
Thanks to the cable trays' straps it can be used for high frequency according to UTEC15-900 (classe D, frequency 16 MHz).L = support distance ( in m )
KKL 80.100
7032 80 100 0,5 3 6500KKL 80.150 7032 80 150 0,5 3 10200KKL 80.200 7032 80 200 0,5 3 13900KKL 80.250 7032 80 250 0,5 3 17600KKL 80.300 7032 80 300 0,5 3 21300KKL 80.400 7032 80 400 1,0 4 27600KKL 80.500 7032 80 500 1,0 4 34800KKL 80.600 7032 80 600 1,0 4 42000
K23
K23K23K23K23K23K23K23
Item ref. RAL colour
Height WidthB
Admissible load
F at L=1,5 m
Materialthickness
(th)
Operatingcross cut
mm mm kN/m mm mm²
Min. pack.
3 m3 m3 m3 m3 m3 m3 m3 m
EANcode
952267952274952281952298952304952311952328952335
Weight 100 units
m
122,0161,0180,0218,7281,0380,0480,0540,0
Warning : the deflection is measured with a junction position between 2 cable trays at a distance L/5from the support. If this distance is not respected, it is necessary to raise the deflection values byapprox. 30%.
GRP cable trayspressed, equipped with a shaped coupler, with reinforced sidewalls (5 mm)
Thanks to the cable trays' straps it can be used for high frequency according to UTEC15-900 (classe D, frequency 16 MHz).L = support distance ( in m )
KK 80.100
7032 80 100 0,5 3 6500KK 80.150 7032 80 150 0,5 3 10200KK 80.200 7032 80 200 0,5 3 13900KK 80.250 7032 80 250 0,5 3 17600KK 80.300 7032 80 300 0,5 3 21300KK 80.400 7032 80 400 1,0 4 27600KK 80.500 7032 80 500 1,0 4 34800KK 80.600 7032 80 600 1,0 4 42000
K23
K23K23K23K23K23K23K23
Item ref. RAL colour
Height WidthB
Admissible load
F at L=1,5 m
Materialthickness
(th)
Operatingcross cut
mm mm kN/m mm mm²
Min. pack.
3 m3 m3 m3 m3 m3 m3 m3 m
EANcode
952069952076952083952090952106952113952120952137
Weight 100 units
m
127165195220230390460470
Warning : the deflection is measured with a junction position between 2 cable trays at a distance L/5from the support. If this distance is not respected, it is necessary to raise the deflection values byapprox. 30%.
End cap for GRP cable traypressed
for the closing of the cable tray ends
Used for: Cable trays KK…, KKL… H80 mm
Mounting accessories required : 2 bolts M6x16 V4A ( to be ordered separately )
KKKE 80.100
7032 80 100KKKE 80.150 7032 80 150KKKE 80.200 7032 80 200KKKE 80.250 7032 80 250KKKE 80.300 7032 80 300KKKE 80.400 7032 80 400KKKE 80.500 7032 80 500KKKE 80.600 7032 80 600
K23
K23K23K23K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
955244955251955268955275955282955299955305955312
Weight 100 units
pc
6,09,0
12,014,017,521,026,035,0
GRP adjustable splice platepressed, horizontal
Need: 2 pieces for each cut
for the horizontal connection of cable trays and fittings H80mm lengthwise
Mounting accessories required : 4 bolts M6x16 V4A ( to be ordered separately )
KKGH 80
7032 65K23
Item ref. RAL colour
Height
mm
Min. pack.
1 set
EANcode
955633
Weight 100 units
3,7
for the cable tray connection with an expansion joint
36
CABLE TRAY SYSTEM K²
Horizontal splice platehorizontal
Need: 2 pieces for each cut
for the horizontal connection of cable trays and fittings H80 mm and for the changes of directions.
Mounting accessories required : 4 bolts M6x16 V4A ( to be ordered separately )
KKIH 80 E4
7032 65E4
Item ref. RAL colour
Height
mm
Min. pack.
1 set
EANcode
955664
Weight 100 units
3,6
for the length adjustment, please leave a space between cable trays.
GRP separatorpressed
The divider KKT 80 is delivered not mounted, it can be fixed in the cable tray with a bolt M 6x16V4A each meter.The divider KKT80/M can be delivered pre-installed (riveted), the position inside the cabletray must be defined in the purchase order.
to separate cables with different functions and / or to separate voltages
KKT 80
7032 67KKT 80/M 7032 67
K23
K23
Item ref. RAL colour
Height
mm
Min. pack.
3 m3 m
EANcode
953035953066
Weight 100 units
m
4040
GRP tee junction for cable tray, small radiuspressed, with interlocking coupler
KKSS 80.100
7032 80 100KKSS 80.150 7032 80 150KKSS 80.200 7032 80 200KKSS 80.250 7032 80 250KKSS 80.300 7032 80 300
K23
K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.
EANcode
954834954841954858954865954872
Weight 100 units
pc
1827222832
During the installation, you must take care to position a support at each cable tray end and to fix themwith bolts M 6x16 V4A.
GRP tee junction for cable tray, large radiuspressed, with interlocking coupler
KKST 80.100
7032 80 100KKST 80.150 7032 80 150KKST 80.200 7032 80 200KKST 80.250 7032 80 250KKST 80.300 7032 80 300KKST 80.400 7032 80 400KKST 80.500 7032 80 500KKST 80.600 7032 80 600
K23
K23K23K23K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
954612954629954636954643954650954667954674954681
Weight 100 units
pc
78,088,090,0
101,0108,5130,0145,0164,0
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the couplers must be fixed laterally by 4 bolts M6x16 V4A on eachtray end.
37
Horizontal elbow 45°pressed, with interlocking coupler
The piece is provided with a sleeve riveted on one side only.
KKC 80.100
7032 80 100 100KKC 80.150 7032 80 150 175KKC 80.200 7032 80 200 200KKC 80.250 7032 80 250 275KKC 80.300 7032 80 300 225KKC 80.400 7032 80 400 250KKC 80.500 7032 80 500 250KKC 80.600 7032 80 600 250
K23
K23K23K23K23K23K23K23
Item ref. RAL colour
Height WidthB
Radius R
mm mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
953448953455953462953479953486953493953509953516
Weight 100 units
pc
22,029,550,070,0
100,0151,0280,0300,0
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the couplers must be fixed laterally by 2 bolts M6x16 V4A on eachtray end.
Horizontal elbow 90°, small radiuspressed, with interlocking coupler
KKW 80.100
7032 80 100KKW 80.150 7032 80 150KKW 80.200 7032 80 200KKW 80.250 7032 80 250KKW 80.300 7032 80 300KKW 80.400 7032 80 400KKW 80.500 7032 80 500KKW 80.600 7032 80 600
K23
K23K23K23K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
953691953707953714953721953738953745953752953769
Weight 100 units
pc
2735536286
125195240
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the couplers must be fixed laterally by 2 bolts M6x16 V4A on eachtray end.
Horizontal elbow 90°, large radiuspressed, with interlocking coupler
KKB 80.100
7032 80 100 125 100KKB 80.150 7032 80 150 200 175KKB 80.200 7032 80 200 225 200KKB 80.250 7032 80 250 300 275KKB 80.300 7032 80 300 250 225KKB 80.400 7032 80 400 325 250KKB 80.500 7032 80 500 325 250KKB 80.600 7032 80 600 325 250
K23
K23K23K23K23K23K23K23
Item ref. RAL colour
Height WidthB
C Radius R
mm mm mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
953202953219953226953233953240953257953264953271
Weight 100 units
pc
41,543,590,0
146,5170,0272,0377,0442,0
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the couplers must be fixed laterally by 2 bolts M6x16 V4A on eachtray end.
GRP right hand reductionpressed, with interlocking coupler
KKRR 80.200
7032 80 200KKRR 80.300 7032 80 300KKRR 80.400 7032 80 400KKRR 80.500 7032 80 500KKRR 80.600 7032 80 600
K23
K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.
EANcode
955046955053955060955077955084
Weight 100 units
pc
92124165190220
During the assembly, every reducer must be supported at each end.To ensure a correct installation, the couplers must be fixed laterally by 2 bolts M6x16 V4A on eachtray end.
38
CABLE TRAY SYSTEM K²
GRP left hand reductionpressed, with interlocking coupler
KKRL 80.200
7032 80 200KKRL 80.300 7032 80 300KKRL 80.400 7032 80 400KKRL 80.500 7032 80 500KKRL 80.600 7032 80 600
K23
K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.
EANcode
954933954940954957954964954971
Weight 100 units
pc
92114163184220
During the assembly, every reducer must be supported at each end.To ensure a correct installation, the couplers must be fixed laterally by 2 bolts M6x16 V4A on eachtray end.
GRP vertical splice platepressed, vertical
Need: 2 pieces for each cut
for the vertical connection of cable trays and fittings H80 with an angle adjustment.
Mounting accessories required : 4 bolts M6x20 V4A ( to be ordered separately )
KKGV 80
7032 65K23
Item ref. RAL colour
Height
mm
Min. pack.
1 set
EANcode
955145
Weight 100 units
9
Stainless steel vertical splice plate V4Avertical
Need: 2 pieces for each cut
for the horizontal connection of cable trays and fittings H80 mm and for the changes of directions.
Mounting accessories required : 4 bolts M6x16 V4A ( to be ordered separately )
KKIV 80 E4
65E4
Item ref. Height
mm
Min. pack.
1 set
EANcode
955176
Weight 100 units
8
GRP changing elevationpressed, with interlocking coupler
Composed with different pieces, the changing elevation can be mounted in different heights
KKET 80.100
7032 80 100 160 480 800KKET 80.150 7032 80 150 160 480 800KKET 80.200 7032 80 200 160 480 800KKET 80.250 7032 80 250 160 480 800KKET 80.300 7032 80 300 160 480 800KKET 80.400 7032 80 400 160 480 800KKET 80.500 7032 80 500 160 480 800KKET 80.600 7032 80 600 160 480 800
K23
K23K23K23K23K23K23K23
Item ref. RAL colour
Height WidthB
HeightH1
HeightH2
HeightH3
mm mm mm mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
954377954384954391954407954414954421954438954445
Weight 100 units
pc
190250259340344420500596
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the couplers must be fixed laterally by 2 bolts M6x16 V4A on eachtray end.The part height depends on the height and the configuration usedH1 = 160 mm =>L1 = 785 mm ( a cut is necessary )H2 = 480 mm =>L2 = 1100 mmH3 = 800 mm =>L3 = 970 mm
39
GRP vertical inside elbowpressed, with interlocking coupler
KKBI 80.100
7032 80 100KKBI 80.150 7032 80 150KKBI 80.200 7032 80 200KKBI 80.250 7032 80 250KKBI 80.300 7032 80 300KKBI 80.400 7032 80 400KKBI 80.500 7032 80 500KKBI 80.600 7032 80 600
K23
K23K23K23K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
954070954087954094954100954117954124954131954148
Weight 100 units
pc
53647590
102123145170
During the assembly, we recommend to support each end of fitting at each cable entry.To ensure a correct installation, the couplers must be fixed laterally by 2 bolts M6x16 V4A on eachtray end.
GRP vertical outside elbowpressed, with interlocking coupler
KKBA 80.100
7032 80 100KKBA 80.150 7032 80 150KKBA 80.200 7032 80 200KKBA 80.250 7032 80 250KKBA 80.300 7032 80 300KKBA 80.400 7032 80 400KKBA 80.500 7032 80 500KKBA 80.600 7032 80 600
K23
K23K23K23K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
953882953899953905953912953929953936953943953950
Weight 100 units
pc
4655627374
100113134
During the assembly, we recommend to support each end of fitting at each cable entry.To ensure a correct installation, the couplers must be fixed laterally by 2 bolts M6x16 V4A on eachtray end.
Mounting platepressed, easy to install, with pre-mounted fixing clamps
The mounting plate is in GRP, only the mounting lug are in stainless steel V4A
for the installation of equipment or junction boxes
MP 80
7032 80E4 K23
Item ref. RAL colour
Height
mm
Min. pack.
1 p.
EANcode
963027
Weight 100 units
pc
17
40
CABLE TRAY SYSTEM K²
GRP cable trayspressed, perforated, equipped with a shaped coupler, with reinforced sidewalls (5 mm)
Thanks to the cable trays' straps it can be used for high frequency according to UTEC15-900 (classe D, frequency 16 MHz).L = support distance ( in m )
KKL 110.100
7032 110 100 1,2 4 8500KKL 110.200 7032 110 200 1,2 4 18800KKL 110.300 7032 110 300 1,2 4 29100KKL 110.400 7032 110 400 1,2 4 39400KKL 110.500 7032 110 500 1,2 4 49700KKL 110.600 7032 110 600 1,2 4 60000
K23
K23K23K23K23K23
Item ref. RAL colour
Height WidthB
Admissible load
F at L=1,5 m
Materialthickness
(th)
Operatingcross cut
mm mm kN/m mm mm²
Min. pack.
3 m3 m3 m3 m3 m3 m
EANcode
952342952359952366952373952380952397
Weight 100 units
m
230300370440510580
Warning : the deflection is measured with a junction position between 2 cable trays at a distance L/5from the support. If this distance is not respected, it is necessary to raise the deflection values byapprox. 30%.
GRP cable trayspressed, equipped with a shaped coupler, with reinforced sidewalls (5 mm)
Thanks to the cable trays' straps it can be used for high frequency according to UTEC15-900 (classe D, frequency 16 MHz).L = support distance ( in m )
KK 110.100
7032 110 100 1,2 4 8500KK 110.200 7032 110 200 1,2 4 18800KK 110.300 7032 110 300 1,2 4 29100KK 110.400 7032 110 400 1,2 4 39400KK 110.500 7032 110 500 1,2 4 49700KK 110.600 7032 110 600 1,2 4 60000
K23
K23K23K23K23K23
Item ref. RAL colour
Height WidthB
Admissible load
F at L=1,5 m
Materialthickness
(th)
Operatingcross cut
mm mm kN/m mm mm²
Min. pack.
3 m3 m3 m3 m3 m3 m
EANcode
952144952151952168952175952182952199
Weight 100 units
m
230300380450520600
Warning : the deflection is measured with a junction position between 2 cable trays at a distance L/5from the support. If this distance is not respected, it is necessary to raise the deflection values byapprox. 30%.
End cap for GRP cable traypressed
for the closing of the cable tray ends
Used for: Cable trays KK…, KKL… H110 mm
Mounting accessories required : 2 bolts M6x16 V4A ( to be ordered separately )
KKKE 110.100
7032 110 100KKKE 110.200 7032 110 200KKKE 110.300 7032 110 300KKKE 110.400 7032 110 400KKKE 110.500 7032 110 500KKKE 110.600 7032 110 600
K23
K23K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
955329955336955343955350955367955374
Weight 100 units
pc
101318222726
GRP adjustable splice platepressed, horizontal
Need: 2 pieces for each cut
for the horizontal connection of cable trays and fittings H110 mm lengthwise
Mounting accessories required : 4 bolts M6x20 V4A ( to be ordered separately )
KKGH 110
7032 89K23
Item ref. RAL colour
Height
mm
Min. pack.
1 set
EANcode
955640
Weight 100 units
2
for the cable tray connection with an expansion joint
41
Horizontal splice platehorizontal
Need: 2 pieces for each cut
Mounting accessories required : 4 bolts M6x16 V4A ( to be ordered separately )
KKIH 110 E4
80E4
Item ref. Height
mm
Min. pack.
1 set
EANcode
955671
Weight 100 units
16,6
for the length adjustment, please leave a space between cable trays.
GRP separatorpressed
The divider KKT 110 is delivered not mounted, it can be fixed in the cable tray with a boltM 6x16 V4A each meter.The divider KKT110/M can be delivered pre-mounted ( riveted ), the position inside the cabletray must be defined in the purchase order.
to separate cables with different functions and / or to separate voltages
KKT 110
7032 102KKT 110/M 7032 102
K23
K23
Item ref. RAL colour
Height
mm
Min. pack.
3 m3 m
EANcode
953042953073
Weight 100 units
pc m/
4040
GRP tee junction for cable tray, large radiuspressed, with interlocking coupler
KKST 110.100
7032 110 100KKST 110.200 7032 110 200KKST 110.300 7032 110 300KKST 110.400 7032 110 400KKST 110.500 7032 110 500KKST 110.600 7032 110 600
K23
K23K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
954698954704954711954728954735954742
Weight 100 units
pc
78,0120,0128,5200,0170,0190,0
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the couplers must be fixed laterally by 4 bolts M6x16 V4A on eachtray end.
Horizontal elbow 45°pressed, with interlocking coupler
The piece is provided with a sleeve riveted on one side only.
KKC 110.100
7032 110 100 200KKC 110.200 7032 110 200 200KKC 110.300 7032 110 300 225KKC 110.400 7032 110 400 250KKC 110.500 7032 110 500 250KKC 110.600 7032 110 600 250
K23
K23K23K23K23K23
Item ref. RAL colour
Height WidthB
Radius R
mm mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
953523953530953547953554953561953578
Weight 100 units
pc
22,065,0
108,5197,0313,0342,0
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mm
Horizontal elbow 90°, small radiuspressed, with interlocking coupler
KKW 110.100
7032 110 100KKW 110.200 7032 110 200KKW 110.300 7032 110 300KKW 110.400 7032 110 400KKW 110.500 7032 110 500KKW 110.600 7032 110 600
K23
K23K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
953776953783953790953806953813953820
Weight 100 units
pc m/
407086
125195240
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mm
42
CABLE TRAY SYSTEM K²
Horizontal elbow 90°, large radiuspressed, with interlocking coupler
KKB 110.100
7032 110 100 125 100KKB 110.200 7032 110 200 225 200KKB 110.300 7032 110 300 250 225KKB 110.400 7032 110 400 325 250KKB 110.500 7032 110 500 325 250KKB 110.600 7032 110 600 325 250
K23
K23K23K23K23K23
Item ref. RAL colour
Height WidthB
C Radius R
mm mm mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
953288953295953301953318953325953332
Weight 100 units
pc
98,0132,5217,0360,0490,0434,0
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the couplers must be fixed laterally by 2 bolts M6x16 V4A on eachtray end.
GRP right hand reductionpressed, with interlocking coupler
KKRR 110.200
7032 110 200KKRR 110.300 7032 110 300KKRR 110.400 7032 110 400KKRR 110.500 7032 110 500KKRR 110.600 7032 110 600
K23
K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.
EANcode
962549955091955107955114955121
Weight 100 units
pc
100124160180240
During the assembly, every fitting must be supported at each end, at the cable entry. To ensure a correct installation, the couplers must be fixed laterally by 2 bolts M6x16 V4A on eachtray end.
GRP left hand reductionpressed, with interlocking coupler
KKRL 110.200
7032 110 200 500KKRL 110.300 7032 110 300 500KKRL 110.400 7032 110 400 500KKRL 110.500 7032 110 500 500KKRL 110.600 7032 110 600 500
K23
K23K23K23K23
Item ref. RAL colour
Height WidthB
Coverslength
mm mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.
EANcode
962532954988954995955008955015
Weight 100 units
pc m/
100124200195220
During the assembly, we recommend to support each end of fitting at each cable entry.To ensure a correct installation, the couplers must be fixed laterally by 2 bolts M6x16 V4A on eachtray end.
GRP vertical splice platepressed, vertical
Need: 2 pieces for each cut
for the vertical connection of cable trays and fittings H110 with an angle adjustment.
Mounting accessories required : 4 bolts M6x20 V4A ( to be ordered separately )
KKGV 110
7032 90K23
Item ref. RAL colour
Height
mm
Min. pack.
1 set
EANcode
955152
Weight 100 units
19
Stainless steel vertical splice plate V4Avertical, stainless steel
Need: 2 pieces for each cut
for the horizontal connection of cable trays and fittings H110 mm and for the changes of directions.
Mounting accessories required : 4 bolts M6x16 V4A ( to be ordered separately )
KKIV 110 E4
80E4
Item ref. Height
mm
Min. pack.
1 set
EANcode
955183
Weight 100 units
36
43
GRP changing elevationpressed, with interlocking coupler
Composed with different pieces, the changing elevation can be mounted in different heights
KKET 110.100
7032 110 100 160 480 800KKET 110.200 7032 110 200 160 480 800KKET 110.300 7032 110 300 160 480 800KKET 110.400 7032 110 400 160 480 800KKET 110.500 7032 110 500 160 480 800KKET 110.600 7032 110 600 160 480 800
K23
K23K23K23K23K23
Item ref. RAL colour
Height WidthB
HeightH1
HeightH2
HeightH3
mm mm mm mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
954452954469954476954483954490954506
Weight 100 units
pc
190210344420480596
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the couplers must be fixed laterally by 2 bolts M6x16 V4A on eachtray end.The part height depends on the height and the configuration usedH1 = 160 mm =>L1 = 785 mm ( a cut is necessary )H2 = 480 mm =>L2 = 1100 mmH3 = 800 mm =>L3 = 970 mm
GRP vertical inside elbowpressed, with interlocking coupler
KKBI 110.100
7032 110 100KKBI 110.200 7032 110 200KKBI 110.300 7032 110 300KKBI 110.400 7032 110 400KKBI 110.500 7032 110 500KKBI 110.600 7032 110 600
K23
K23K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
954155954162954179954186954193954209
Weight 100 units
pc
53100123143175170
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the couplers must be fixed laterally by 2 bolts M6x16 V4A on eachtray end.
GRP vertical outside elbowpressed, with interlocking coupler
KKBA 110.100
7032 110 100KKBA 110.200 7032 110 200KKBA 110.300 7032 110 300KKBA 110.400 7032 110 400KKBA 110.500 7032 110 500KKBA 110.600 7032 110 600
K23
K23K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
953967953974953981953998954001954018
Weight 100 units
pc
4682
110130205138
During assembly, all the fittings must be supported at every cables entry, add a centrale support for allfittings with radius greater than 250 mm, and/or with width greater than 400 mmTo ensure a correct installation, the couplers must be fixed laterally by 2 bolts M6x16 V4A on eachtray end.
44
CABLE TRAY SYSTEM K²
Mounting platepressed, easy to install, with pre-mounted fixing clamps
The mounting plate is in GRP, only the mounting lug are in stainless steel V4A
for the installation of equipment or junction boxes
MP 110
7032 110E4 K23
Item ref. RAL colour
Height
mm
Min. pack.
1 p.
EANcode
963034
Weight 100 units
pc
17
45
NOTES
46
CABLE TRAY SYSTEM COVERS K²
Cover for cable trays and cable ladderspressed
For a stronger assembly, the covers with a width above 400 mm are strengthened. Thesestrengthenings / ribs are visible on the outside face of the part.Used for: Cable tray H50, H80 and H110 mm, KK…, KKL… and cable ladder UL…H53, H80, H100
and H150 mm
KKD 100
7032 100KKD 150 7032 150KKD 200 7032 200KKD 250 7032 250KKD 300 7032 300KKD 400 7032 400KKD 500 7032 500KKD 600 7032 600
K23
K23K23K23K23K23K23K23
Item ref. RAL colour
WidthB
mm
Min. pack.
3 m3 m3 m3 m3 m3 m3 m3 m
EANcode
956111956128956135956142956159956166956180956197
Weight 100 units
pc
78105132152190243292338
For a strong and compliant assembly, we recommend to leave a minimum distance of 8 mm betweenthe covers and the sidewalls of cable trays. Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, storms for example, the quantity of clips must be increased.
GRP cover for horizontal elbow 45°, small radiuspressed
Used for: Elbow 45° H50, H80 and H110 mm, KKC… and KPC…/P
KKCD 100
7032 100KKCD 150 7032 150KKCD 200 7032 200KKCD 250 7032 250KKCD 300 7032 300KKCD 400 7032 400KKCD 500 7032 500KKCD 600 7032 600
K23
K23K23K23K23K23K23K23
Item ref. RAL colour
WidthB
mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
956456956463956470956487956494956500956517956524
Weight 100 units
pc
1223335051
138150173
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, storms for example, the quantity of clips must be increased.
Cover for horizontal elbow 90°, large radiuspressed
Used for: Horizontal elbow 90°, large radius, H50, H80 and H110, KKB… and KPB…/P
KKBD 100
7032 100KKBD 150 7032 150KKBD 200 7032 200KKBD 250 7032 250KKBD 300 7032 300KKBD 400 7032 400KKBD 500 7032 500KKBD 600 7032 600
K23
K23K23K23K23K23K23K23
Item ref. RAL colour
WidthB
mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
956371956388956395956401956418956425956432956449
Weight 100 units
pc
19,543,068,097,0
115,0241,0334,0403,0
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, storms for example, the quantity of clips must be increased.
47
Cover for horizontal elbow 90°, small radiuspressed
Used for: Horizontal elbow 90°, H50, H80 and H110, KKW…
KKWD 50
7032 50KKWD 100 7032 100KKWD 150 7032 150KKWD 200 7032 200KKWD 250 7032 250KKWD 300 7032 300KKWD 400 7032 400KKWD 500 7032 500KKWD 600 7032 600
K23
K23K23K23K23K23K23K23K23
Item ref. RAL colour
WidthB
mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
956531956548956555956562956579956586956593956609956616
Weight 100 units
pc
6,011,521,031,041,560,093,0
125,0187,0
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, storms for example, the quantity of clips must be increased.
GRP cover for vertical inside elbowpressed
Used for: Vertical inside elbow 50 mm high, KKBI… and KPBI…/P
KKBID 50.050
7032 50 50KKBID 50.100 7032 50 100KKBID 50.150 7032 50 150KKBID 50.200 7032 50 200KKBID 50.300 7032 50 300
K23
K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.
EANcode
956814956821956838956845956852
Weight 100 units
pc
520425063
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, storms for example, the quantity of clips must be increased.
GRP cover for vertical inside elbowpressed
Used for: Vertical inside elbow 80 mm high, KKBI… and KPBI…/P
KKBID 80.100
7032 80 100KKBID 80.150 7032 80 150KKBID 80.200 7032 80 200KKBID 80.250 7032 80 250KKBID 80.300 7032 80 300KKBID 80.400 7032 80 400KKBID 80.500 7032 80 500KKBID 80.600 7032 80 600
K23
K23K23K23K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
956869956876956883956890956906956913956920956937
Weight 100 units
pc
18,024,533,040,045,561,073,095,0
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, storms for example, the quantity of clips must be increased.
GRP cover for vertical inside elbowpressed
Used for: Vertical inside elbow 110 mm high, KKBI… and KPBI…/P
KKBID 110.100
7032 110 100KKBID 110.200 7032 110 200KKBID 110.300 7032 110 300KKBID 110.400 7032 110 400KKBID 110.500 7032 110 500KKBID 110.600 7032 110 600
K23
K23K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
956944956951956968956975956982956999
Weight 100 units
pc
183050
100120130
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, storms for example, the quantity of clips must be increased.
48
CABLE TRAY SYSTEM COVERS K²
GRP cover for vertical outside elbowpressed
Used for: Vertical outside elbow H50 mm, KKBA… and KPBA…/P
KKBAD 50.050
7032 50 50KKBAD 50.100 7032 50 100KKBAD 50.150 7032 50 150KKBAD 50.200 7032 50 200KKBAD 50.300 7032 50 300
K23
K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.
EANcode
956623956630956647956654956661
Weight 100 units
pc
7,810,042,051,065,0
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, storms for example, the quantity of clips must be increased.
GRP cover for vertical outside elbowpressed
Used for: Vertical outside elbow H80 mm, KKBA… and KPBA…/P
KKBAD 80.100
7032 80 100KKBAD 80.150 7032 80 150KKBAD 80.200 7032 80 200KKBAD 80.250 7032 80 250KKBAD 80.300 7032 80 300KKBAD 80.400 7032 80 400KKBAD 80.500 7032 80 500KKBAD 80.600 7032 80 600
K23
K23K23K23K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
956678956685956692956708956715956722956739956746
Weight 100 units
pc
29,539,051,061,072,090,0
120,0136,0
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, storms for example, the quantity of clips must be increased.
GRP cover for vertical outside elbowpressed
Used for: Vertical outside elbow H110 mm, KKBA… and KPBA…/P
KKBAD 110.100
7032 110 100KKBAD 110.200 7032 110 200KKBAD 110.300 7032 110 300KKBAD 110.400 7032 110 400KKBAD 110.500 7032 110 500KKBAD 110.600 7032 110 600
K23
K23K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
956753956760956777956784956791956807
Weight 100 units
pc
35507080
120130
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, storms for example, the quantity of clips must be increased.
GRP cover for changing elevationpressed
1 KKETD is composed of :- 1 GRP cover for inside elbow- 1 GRP cover for outside elbowUsed for: Changing elevation H50 mm KKET… and KPET…/P
KKETD 50.100
7032 50 100KKETD 50.150 7032 50 150KKETD 50.200 7032 50 200KKETD 50.300 7032 50 300
K23
K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.
EANcode
957002957019957026957033
Weight 100 units
pc
20414060
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, storms for example, the quantity of clips must be increased.
49
GRP cover for changing elevationpressed
1 KKETD is composed of :- 1 GRP cover for inside elbow- 1 GRP cover for outside elbowUsed for: Changing elevation H50 mm KKET… and KPET…/P
KKETD 80.100
7032 80 100KKETD 80.150 7032 80 150KKETD 80.200 7032 80 200KKETD 80.250 7032 80 250KKETD 80.300 7032 80 300KKETD 80.400 7032 80 400KKETD 80.500 7032 80 500KKETD 80.600 7032 80 600
K23
K23K23K23K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
957040957057957064957071957088957095957101957118
Weight 100 units
pc
23,531,740,544,047,061,098,0
120,0
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, storms for example, the quantity of clips must be increased.
GRP cover for changing elevationpressed
1 KKETD is composed of :- 1 GRP cover for inside elbow- 1 GRP cover for outside elbowUsed for: Changing elevation H110 mm KKET…
KKETD 110.100
7032 110 100KKETD 110.200 7032 110 200KKETD 110.300 7032 110 300KKETD 110.400 7032 110 400KKETD 110.500 7032 110 500KKETD 110.600 7032 110 600
K23
K23K23K23K23K23
Item ref. RAL colour
Height WidthB
mm mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
957125957132957149957156957163957170
Weight 100 units
pc
23,540,047,061,098,0
120,0
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, storms for example, the quantity of clips must be increased.
GRP cover for tee junction, large radiuspressed, with interlocking coupler
Used for: Cover for tee junction for H50, H80 and H110 mm, KKST… and KPST…/P
KKSTD 100
7032 100KKSTD 150 7032 150KKSTD 200 7032 200KKSTD 250 7032 250KKSTD 300 7032 300KKSTD 400 7032 400KKSTD 500 7032 500KKSTD 600 7032 600
K23
K23K23K23K23K23K23K23
Item ref. RAL colour
WidthB
mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
957187957194957200957217957224957231957248957255
Weight 100 units
pc
354252636578
100118
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, storms for example, the quantity of clips must be increased.
Tee junction cover, small radiuspressed, with interlocking coupler
Used for: Tee junction for H50 and H80 mm, KKSS… and KPSS…/P
KKSSD 50
7032 50KKSSD 100 7032 100KKSSD 150 7032 150KKSSD 200 7032 200KKSSD 250 7032 250KKSSD 300 7032 300
K23
K23K23K23K23K23
Item ref. RAL colour
WidthB
mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.1 p.
EANcode
957262957279957286957293957309957316
Weight 100 units
pc
5,08,09,5
13,014,515,5
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, storms for example, the quantity of clips must be increased.
50
CABLE TRAY SYSTEM COVERS K²
GRP cover for right hand reductionpressed
Used for: Right hand reduction H50, H80 and H110 mm, KKRR…
KKRRD 200
7032 200KKRRD 300 7032 300KKRRD 400 7032 400KKRRD 500 7032 500KKRRD 600 7032 600
K23
K23K23K23K23
Item ref. RAL colour
WidthB
mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.
EANcode
957378957385957392957408957415
Weight 100 units
pc
50,579,0
119,0131,0160,0
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, storms for example, the quantity of clips must be increased.
GRP cover for left hand reductionpressed
Used for: Reduction H50, 80 and 110 mm, KKRL…
KKRLD 200
7032 200KKRLD 300 7032 300KKRLD 400 7032 400KKRLD 500 7032 500KKRLD 600 7032 600
K23
K23K23K23K23
Item ref. RAL colour
WidthB
mm
Min. pack.
1 p.1 p.1 p.1 p.1 p.
EANcode
957323957330957347957354957361
Weight 100 units
pc
4975
110147160
Covers are attached by using stainless steel cover clips DF…V4A, DF M… and DFUB… In extremeweather conditions, strong winds, storms for example, the quantity of clips must be increased.
Cover fixing clipstainless steel
for fixing the cables tray covers and fittings
Used for: Cable tray cover KKD… and KPD…Cover for fittings KKCD..., KKBD..., KKWD..., KKBAD..., KKBID..., KKETD..., KKSTD...,KKSSD..., KKRLD... and KKRRD...
DF 50 E4
55DF 80 E4 85DF 100 E4 110
E4
E4E4
Item ref. Height
mm
Min. pack.
50 p.50 p.50 p.
EANcode
957873957880957897
Weight 100 units
pc.
1,72,12,3
Under normal conditions, it is recommended to mount 1 clip each meter alternatively every 3 meters.Under extreme weather conditions, such as strong winds or storms, the quantity of clips must beincreased.
Cover fixing
Used for: Cover for cable tray KKD… and KPD…Cover for fittings KKCD..., KKBD..., KKWD..., KKBAD..., KKBID..., KKETD..., KKSTD...,KKSSD..., KKRLD... und KKRRD…
DF M
K01
Item ref. Min. pack.
50 p.
EANcode
957927
Weight 100 units
pc.
0,2
For fixing the cover, it is necessary to drill a 8,2 mm diameter hole for the diameter. In extremeweather conditions such as strong winds, for example, the quantity of clips must be increased.
Cover fixing
Used for: Cover for cable tray KKD… and KPD…Cover for fittings KKCD..., KKBD..., KKWD..., KKBAD..., KKBID..., KKETD..., KKSTD...,KKSSD..., KKRLD... und KKRRD…
DFUB 5.5X19 E4
N E4
Item ref. Min. pack.
50 p.
EANcode
062065
Weight 100 units
0,64
For fixing the cover, it is necessary to drill a 8,2 mm diameter hole for the diameter. In extremeweather conditions such as strong winds, for example, the quantity of clips must be increased.
51
Cover fixing clipstainless steel
for fixing the cables tray covers and fittings
Used for: Cable tray cover KKD…
DF 1060 E4
E4
Item ref. Min. pack.
50 p.
EANcode
957910
Weight 100 units
pc.
1,1
Under normal conditions, it is recommended to mount 1 clip each meter alternatively every 3 meters.Under extreme weather conditions, such as strong winds or storms, the quantity of clips must beincreased.
52
CABLE TRAY SYSTEM ACCESSOIRES K²
Separating studpultruded
Not suitable when the cable tray is mounted vertically (not horizontally)
for an easy mounting of cables and connections
TB
K01
Item ref. Min. pack.
1 p.
EANcode
957934
Weight 100 units
m
1
When mounting the separating stud, it is necesary to drill a 10 mm hole diameter in the base.
Dome head boltIncluded nut and washer
Also named M6x16V4A for FKM 6x16 E4, M6x20V4A for FKM 6x20 E4, M8x20PA6 for FKM 8x20K01, M10x30V4A for SKM 10x30 E4
FKM 6X16 E4
6 16FKM 6X20 E4 6 20
E4
E4
Item ref. ThreadM
LengthL
mm
Min. pack.
100 p.100 p.
EANcode
962693962709
Weight 100 units
pc
1,21,4
Dome head boltIncluded nut and washer
Also named M6x16V4A for FKM 6x16 E4, M6x20V4A for FKM 6x20 E4, M8x20PA6 for FKM 8x20K01, M10x30V4A for SKM 10x30 E4
FKM 8X20 K01
8 20K01
Item ref. ThreadM
LengthL
mm
Min. pack.
100 p.
EANcode
962716
Weight 100 units
pc
0,4
Hexagon head boltIncluded nut and washer
Also named M6x16V4A for FKM 6x16 E4, M6x20V4A for FKM 6x20 E4, M8x20PA6 for FKM 8x20K01, M10x30V4A for SKM 10x30 E4
SKM 10X30 E4
10 30SKM 10X40 E4 10 40
E4
E4
Item ref. ThreadM
LengthL
mm
Min. pack.
100 p.100 p.
EANcode
962730962747
Weight 100 units
pc
4,55,1
53
NOTES