distributor tech data distributor tech data - ceco door area... · ceco door products distributor...

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech Data

Technical Information:Prime Paint Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-002Colorstyle Paint Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-003

Frame, Door Opening Sizes and Hardware Provisions:1-3/8” Door - Single and Double . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-101Hardware Locations - Standard 1-3/8” Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-1021-3/4” Door - Single and Double . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-103Hardware Locations - Standard 1-3/4” Door 6-8, 7-0, 7-2 High, 4-1/2” or 5” High Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-104 7-10, 8-0, 9-0, 10-0 High, 4-1/2” or 5” High Hinge . . . . . . . . . . . . . . . . . . . . . . . .11-104A 5-0 Thru 10-0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-104B, 11-104C 6-8, 7-0, 7-2, 8-0 High, Dutch, 4-1/2” or 5” High Hinge . . . . . . . . . . . . . . . . . . . .11-104DHardware Locations - Optional (NAAMM), 1-3/4“ Door 6-8, 7-0, 7-2 High, 4-1/2” High Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-105 7-10, 8-0, 9-0 High, 4-1/2” High Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-105A 6-8, 7-0, 7-2 High, 5” High Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-106 7-10, 8-0, 9-0 High, 5” High Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-106A1-3/8” Door Frames, Hinge and Strike Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-2011-3/4” Door Frames, 4-1/2” and 5” Hinge Preparations . . . . . . . . . . . . . . . . . . . . . . . . . .11-2021-3/4” Door Frames, ANSI (4-7/8”) Strike Preparations. . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2031-3/4” Cylindrical Strike Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-204Series SQW Weatherstrip Kerf Frame Hinge Preparation. . . . . . . . . . . . . . . . . . . . . . . . . 11-205Series SQW Weatherstrip Kerf Frame Strike Preparation. . . . . . . . . . . . . . . . . . . . . . . . . 11-206Full Depth Hinge Reinforcement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-207High Frequency Hinge Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-2081-3/8” and 1-3/4” Door Frame Mute Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-209Reversible Flush Bolt Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-210

Frame Construction:Double Rabbet Frames, Die-cut, Welded Corner Assembly T-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-301Double Rabbet Frames, Die-cut, Welded Corner Assembly T-2, T-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-302Double Rabbet Frames, Die-cut, Welded Corner Assembly V-1, V-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-303Double Rabbet Frames, Die-cut, Welded Corner Assembly V-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-304Double Rabbet Frames, Miter-sawed, Welded Corner Assembly V-4, V-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-305Double Rabbet Frames, Coped, Butted, Welded Corner Assembly V-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-306Double Rabbet Frames, Welded Junctions Assembly V-8, V-9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-307

SECTION 11 - FRAMES, GENERAL

INDEX

11-001


Hardware Reinforcements:Closer Reinforcements, Plate Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-401, 11-402Miscellaneous Hardware Reinforcements, Plate Type . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-403

Frame Anchors:Anchor Quantity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-500Floor Anchors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-501 thru 11-503Masonry Anchors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-504, 11-505Existing Opening Anchors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-505 thru 11-507Wood Stud Anchors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-508, 11-509Metal Stud Anchors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-510, 11-511Before Drywall Stud Anchor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-512Closure Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-512Frame Splines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-513

Special Information:Standard Frame Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-901, 11-902Frame Spreader Bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-903

SECTION 11 - FRAMES, GENERAL

INDEX

11-001A

COLORSTYLE PAINT DATA DOOR FRAMES

Process Data

Factory-applied Colorstyle finish is a two-part, urethane top-coat that is electrostatically applied over the standard primer. The paint is then oven cured.

The chemically reactive cure provides a top quality, abrasion resistant finish with excellent weathering characteristics. This finish is environmentally friendly in that it does not contain heavy metal pigments.

60˚ Gardner Gloss: 15 to 20.Colors: Standard color selectors available upon request.

Performance Data

Colorstyle, factory applied finish paint process has been subjected to the following tests: Salt Spray Humidity Accelerated Weathering Impact Film Adhesion Abrasion

Factory applied Colorstyle finish paint meets the performance requirements and acceptance criteria as stated in ANSI Standard A250.3, “Test Procedure and Acceptance Criteria for Factory Applied Finish Painted Steel Surfaces...”.

11-003


NOMINAL SIZES

NOMINAL DOOROPENING WIDTH

NO

MIN

AL

DO

OR

OPE

NIN

G H

EIG

HT

NOMINAL DOOR OPENING WIDTH

NO

MIN

AL

DO

OR

OPE

NIN

G H

EIG

HT

SINGLE FRAME

FLOORFINISH

DOUBLE FRAME

WIDTH WIDTH

2-8

2-10

3-0

2-4

2-6

2-0

5-4

6-0

5-8

4-8

5-0

4-0

OPENING HEIGHT

SINGLE PAIR

6-8 7-0 7-2

STANDARD DOOR OPENING SIZES

FRAMES ON THIS PAGE ARE FOR USE WITH 1-3/8" THICK DOORS.

1-3/8” DOOR FRAME

11-101

7-2 7-0 6-8 6-8

7-2 7-0 6-8

10.37"

9.75"

10.37"

9.75"

LC

STRIKEHEIGHT

STRIKEHEIGHT

*

LC

LC

LC

LC

LC

LC

LC

LC

32.9

3"32

.93"

31.9

3"

29.9

3"

31.9

3"

29.9

3"

59.8

7"

26.1

8"

24.1

8"

20.1

8"

19.5

"20

.18" 33.62"

40.31"

HIN

GE

SPA

CIN

G

HIN

GE

SPA

CIN

G

1640( )5"

810( )3"

9( )3"4

32 ()

1615"

15"

16(31

)

15"

16(29

)

15"

16(32

)

15"

16(31

)

15"

16(29

)

59 (7")

8

( 4 )3"9

26 (3" 16)

24 (16

)3"

20 (16

)3"

19 (1")

2(20

163")

10( )83"

( )833 5"

DUTCH DOOR FRAME

STANDARD FRAME

FRAME HEIGHTS

FRAME HEIGHTS

Labeled 6-8 frames require3 hinges.

2 hinges standard for non-labeled6-8 frames

3 hinges optional for non-labeled 6-8 frames

*

11-102

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech Data1-3/8” DOOR FRAMES HINGE AND STRIKE LOCATIONS

NOMINAL SIZES

1-3/4” DOOR FRAME SIZES

11-103

FLOORFINISH

NOMINAL DOOROPENING WIDTH

NO

MIN

AL

DO

OR

OPE

NIN

G H

EIG

HT

NOMINAL DOOR OPENING WIDTH

NO

MIN

AL

DO

OR

OPE

NIN

G H

EIG

HT

SINGLE FRAME DOUBLE FRAME

8-0

3-10

4-0

3-8

8-0

7-8

7-4

WIDTH WIDTH

2-8

2-10

3-6

3-4

3-0

2-4

2-6

2-0

5-4

7-0

6-8

6-0

5-8

4-8

5-0

4-0

OPENING HEIGHT

SINGLE PAIR

6-8 7-0 7-107-2 10-09-0

5-0 10-0

STANDARD DOOR OPENING SIZES

These hardware locations are Ceco Door Productsstandard and will be furnished unless

otherwise agreed to.

STANDARD HARDWARE LOCATIONS 1-3/4"DOOR FRAMES: 6-8, 7-0 & 7-2 HEIGHTS

4-1/2" OR 5" HIGH HINGES

11-104 12/1/04

9"

9"

DOOR OPENING HEIGHTS

6-87-07-2

34"

34"

33"

33"

31"

31"

STRIKEHEIGHT

CL

CL

CL

CL

41.81"

HIN

GE

SPA

CIN

G

13"1641( )

11-104

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataSTANDARD HARDWARE LOCATIONS 1-3/4”DOOR FRAMES: 6-8, 7-0 & 7-2 HEIGHTS4-1/2” OR 5” HIGH HINGES

These hardware locations are Ceco Door Productsstandard and will be furnished unless

otherwise agreed to.

approximation to .33".21/64" represents a measurable*

NOMINAL SIZES

STANDARD HARDWARE LOCATIONS FOR1-3/4” DOOR FRAMES:7-10, 8-0, 9-0, AND 10-0 HEIGHTS

11-104A

26"

34"

34"

26"

25.3

3"

26"

34"

41.81"

STRIKEHEIGHT

9"

9"

7-108-010-0


9-0

30"

30"

30"

CL

CL

CL

CL

CL

HIN

GE

SPA

CIN

G

13"1641( )

21"

64(25

)*

64(

)25

.33"

2521

"*

64(

)25

.33"

2521

"*

NOMINAL SIZES

FACTORY STANDARD HARDWARELOCATIONS: HEIGHTS 5’-0” THRU 10’-0”

11-104C

5'-1" 3 2 @ 21.5"

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

5'-2" 2 @ 22"

5'-3" 2 @ 22.5"

5'-4" 2 @ 23"

5'-5" 2 @ 23.5"

5'-6" 2 @ 24"

5'-7" 2 @ 24.5"

5'-8" 2 @ 25"

5'-9" 2 @ 25.5"

5'-10" 2 @ 26"

5'-11" 2 @ 26.5"

6'-0" 2 @ 27"

6'-1" 2 @ 27.5"

6'-2" 2 @ 28"

6'-3" 2 @ 28.5"

6'-4" 2 @ 29"

6'-5" 2 @ 29.5"

6'-6" 2 @ 30"

6'-7" 2 @ 30.5"

6'-8" 2 @ 31"

6'-9" 2 @ 31.5"

6'-10" 2 @ 32"

6'-11" 2 @ 32.5"

7'-0" 2 @ 33"

7'-1" 2 @ 33.5"

7'-2" 2 @ 34"

7'-3" 2 @ 34.5"

7'-4" 2 @ 35"

7'-5" 2 @ 35.5"

7'-6" 2 @ 36"

9'-9"

10'-0"

9'-11"

9'-10"

9'-2"

9'-8"

9'-7"

9'-6"

9'-5"

9'-4"

9'-3"

9'-1"

9'-0"

8'-11"

8'-10"

8'-9"

8'-8"

8'-1"

8'-7"

8'-6"

8'-5"

8'-4"

8'-3"

8'-2"

8'-0"

7'-11"

7'-10"

7'-9"

7'-8"

7'-7" 4 3 @ 24.33"4

4

4

4

4

4

4

4

4

4

4

4

4

4

4

4

4

4

4

4

4

4

4

4

4

4

4

4

4

3 @ 24.66"

3 @ 25"

3 @ 25.33"

3 @ 25.66"

3 @ 26"

3 @ 26.33"

3 @ 26.66"

3 @ 27"

3 @ 27.33"

3 @ 27.66"

3 @ 28"

3 @ 28.33"

3 @ 28.66"

3 @ 29"

3 @ 29.33"

3 @ 29.66"

3 @ 30"

3 @ 30.33"

3 @ 30.66"

3 @ 31"

3 @ 31.33"

3 @ 31.66"

3 @ 32"

3 @ 32.33"

3 @ 32.66"

3 @ 33"

3 @ 33.33"

3 @ 33.66"

3 @ 34"

5'-0" 2 42"

OPENING HEIGHT NUMBER OF HINGES DIM "A"



LC

9"


7-2 7-0 6-8

HEIGHTSTRIKE

8-0

33.62"

9"

CL

LC

LC

LC

38.3

1"

28.3

1"

26.3

1"

22.3

1"

17.3

7"H

ING

E SP

AC

ING

16(

5"38

)

5"(

)16

28

5"(

)16

26

5"(

)16

22

22.3

1"(

16)

225"

17 (3")

8

33( 5")8

otherwise agreed to.standard and will be furnished unless

These hardware locations are Ceco Door Products

11-104D

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataSTANDARD HARDWARE LOCATIONS, 1-3/4”DUTCH FRAMES: 6-8, 7-0, 7-2 & 8-0HEIGHTS - 4-1/2” OR 5” HIGH HINGES

HARDWARE LOCATIONS SHOWN BELOW ARE BASEDON THE FOLLOWING:

5" from head to top of upper hinge.10" from bottom of jamb to bottom of lower

Equal spacing between intermediate hinges.

The above hardware locations will befurnished only when agreed to.

Strike Height On Frame IsDependent On Knob OrCrossbar Height. Refer ToDoor Hardware Locations(p. 01-403) And Manufacturer'sLock Template To DetermineRelationship Between Lock And Strike.

hinge.

NOMINAL SIZES

NAAMM ALTERNATE HDWE LOCATIONS, 1-3/4”DOOR FRAMES: 6-8, 7-0 & 7-2 HEIGHTS4-1/2” HIGH HINGES

11-105

LC

LC

12.25"

7-2


LC7.25"

6-87-0

33.2

5"

32.2

5"

30.2

5"H

ING

E SP

ACI

NG

33.2

5"

32.2

5"

30.2

5"

7( 1" )4

33 (1"

)4

)4

(321"

)4

(301"

)4

(331"

(4

)32

1"

30 (4

)1"

( 4 )12 1"


hinge.10" from bottom of jamb to bottom of lower5" from head to top of upper hinge.

ON THE FOLLOWING:HARDWARE LOCATIONS SHOWN BELOW ARE BASED



(p. 01-403a) And Manufacturer'sLock Template To DetermineRelationship Between Lock

Strike Height On Frame Is

Crossbar Height. Refer ToDoor Hardware Locations

Dependent On Knob Or

And Strike.

NOMINAL SIZES

NAAMM HDWE LOCATIONS, 1-3/4” DOORFRAMES: 7-10, 8-0, 9-0, AND 10-0HEIGHTS - 4-1/2” HIGH HINGES

11-105A

L

12.25"LC

CL


10-0 9-0

7.25"

7-108-0

C

CL

HIN

GE

SPA

CIN

G24

.83"

7( )1"4

( )412 1"

33.5

"2

()

1"33

29.5

"2

()

1"29

25.5

"2

()

1"25

53"

64(24

)*

24.8

3"24 (

* )53

"64

24.8

3"24 (

* )53

"64

)(

233

.5"

331"

29.5

"29

)(

1" 2 1")

(25

.5"

252

)(

233

.5"

331"

29.5

"29

)(

1" 2 1")

(25

.5"

252


HARDWARE LOCATIONS SHOWN BELOW ARE BASED ON THE FOLLOWING:

5" from head to top of upper hinge.10" from bottom of jamb to bottomof lower hinge.Equal spacing between intermediatehinges.

(p. 01-404) And Manufacturer'sLock Template To DetermineRelationship Between Lock




And Strike.

33"

LC

LC

12.5"

32"

30"

7-2


33"

LC

32"

30"

7.5"

6-87-0

HIN

GE

SPA

CIN

G

7( 1" )2

12( 1" )2

11-106

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataNAAMM ALTERNATE HDWE LOCATIONS, 1-3/4”DOOR FRAMES: 6-8, 7-0 & 7-2 HEIGHTS5” HIGH HINGES


hinge.10" from bottom of jamb to bottom of lower5" from head to top of upper hinge.

ON THE FOLLOWING:HARDWARE LOCATIONS SHOWN BELOW ARE BASED



21/32" represents a measurableapproximation to .66".

*

(p. 01-404a) And Manufacturer'sLock Template To DetermineRelationship Between Lock




And Strike.

L

LC

CL


10-0 9-0

7.5"

7-108-0

C

CL

12.5"

33.3

3"

29.3

3"

25.3

3"

24.6

6"H

ING

E SP

ACI

NG

7( 1" )2

33.3

3"

29.3

3"

25.3

3"

24.6

6"

33.3

3"

29.3

3"

25.3

3"

24.6

6"

12( 1" )2

21"

32(24

)

21"

64(25

)

21"

64(29

)

21"

64(33

))

(6421

"33 29

)(

21"

64

)(

21"

6425

3221"

24 ()

)(

6421"

33 29)

(21

"64

)(

21"

6425

3221"

24 ()

* * * *

****

* * * *

11-106A

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataNAAMM ALTERNATE HDWE LOCATIONS1-3/4” DOOR FRAMES: 7-10, 8-0, 9-0AND 10-0 HEIGHTS - 5” HIGH HINGES

IS WELDED TO JAMBAFTER HINGE REINF.SNAPPED-IN PLACEPLASTER GUARD IS26 GAGE STEEL

GUARDPLASTER

PER FRAME GAGEFACE NOTCH VARIES

HINGE PREPARATION

TAPPED HOLES FOR #10-24 MS(3) PLACES

FOR USE WITH 3-1/2" HIGHTEMPLATE HINGES (ANSI A156.7)

STEEL STRIKE REINF.PROJECTION WELDED(2) PLACES EACH END

16 GAGE FORMED

16 GAGE STRIKEREINFORCEMENT

PLASTER GUARDFORMED AS PARTOF STRIKE REINF.

STRIKE REINFORCEMENTUSE WITH CYLINDRICAL LOCKS ONLY

(1-1/8" x 2-3/4" "T" STRIKE)

PIERCE, DRAW ANDTAP FOR #8-32 MSTO PROVIDE A MIN.1/8" THREAD DEPTH

12 GA. HINGE REINF.PROJECTION WELDEDTO FRAME (3) PLACESEACH END

5/16"(NOM.)BACKSET

1-1/4"

8"

1-9/16"

3-1/2"

1-25/64"

1-25/64"

23/64"

23/64"

3/8"

21/64"

BACKSET

1-9/16"

1-5/32"

FACE NOTCH VARIESPER FRAME GAGE

3/16"(NOM.)

7/32"

2-25/32"

2-1/8"

1-17/32"

21/64"

21/64"

(NOM.)1-1/4"

NOMINAL SIZES

1-3/8” DOOR FRAMESTRIKE AND HINGE PREPS

11-201

11-202

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech Data1-3/4” DOOR FRAME4-1/2” & 5” HINGE PREPS

16 GAGE FORMED STEEL STRIKEREINFORCEMENT PROJECTIONWELDED (2) PLACES EACH END

PIERCE, DRAW AND TAP FOR#8-32 MS TO PROVIDE AMINIMUM 1/8" THREAD DEPTH

PLASTER GUARD FORMEDAS PART OF STRIKEREINFORCEMENT

2 1"8

1 17"32

2 25"32

13"32

1 5"32

21"64

21"64

1 15"16

CUTOUT

(NOM.)BACKSET

3"8

11-204

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech Data1-3/4” DOOR FRAME CYLINDRICAL STRIKE PREPARATION

2

NOMINAL SIZES

SERIES SQW WEATHERSTRIPKERF FRAME HINGE PREPARATION

11-205

FACE NOTCH VARIES

5/16"

5/8"

1/2"

1-1/4"

9"

PER FRAME GAGE

2-1/8"

AND HINGE WEIGHT

4-1/2"

1/2"(NOM.)

1-1/8"

1-1/8"

1-1/4"

1/2"

(N0M.)1-5/8"

BACKSET

2-1/8"

BACKSET1/2"(NOM.)

1-1/2"

1-1/4"

FACE NOTCH VARIESPER FRAME GAGEAND HINGE WEIGHT

1/2"

5"

1-1/4"

1/2"

(N0M.)1-5/8"

5/16"

5/8"

9"

1-1/4"

FIT FOAM FILLEDWEATHERSTRIP

TO FRAMEAFTER FINISH

PAINTING

PLASTERGUARD

2

PLASTER GUARD ISSNAPPED-IN PLACE.HINGE REINFORCEMENT

26 GAGE STEEL

IS WELDED TO JAMB.

4-1/2" HINGE PREP

(ANSI A156.7)TEMPLATE HINGESFOR USE WITH 5" HIGH

5" HINGE PREP

FOR USE WITH 4-1/2" HIGH

PLASTER GUARD ISSNAPPED-IN PLACE.HINGE REINFORCEMENTIS WELDED TO JAMB.

TEMPLATE HINGES(ANSI A156.7)

26 GAGE STEEL

PLACES EACH END

(4) PLACESFOR #12-24 MS

TAPPED HOLE

7 GAGE HINGEREINFORCEMENTPROJECTION WELDED (4)

(4) PLACES.180 HINGESREMOVED FORBUT MUST BEFOR .134 HINGESREMAIN INTACT ELEVATED PIPS

TAPPED HOLE FOR

PLASTER

7 GAGE HINGE REINFORCEMENTPROJECTION WELDED TO FRAME(4) PLACES EACH END

#12-24 M.S.(4) PLACES

GUARD

11-206 12/1/04

4 1"8

2 1"8

BACKSET (NOM.)

CUTOUT

1"2

11"32

1 9"32

3 13"32

4 29"32

1"2 8

1 17"32

2 1"8

2 25"32

9"16

1 5"32

13"32

BACKSET (NOM.)

CUTOUT

FACE NOTCH VARIESPER FRAME GAGE

25"64

25"64

6421"

21"64

16 GAGE FORMEDSTEEL STRIKE REINF.PROJECTION WELDED(2) PLACES EACH END

PIERCE, DRAW AND TAP FOR #8-32 MSTO PROVIDE A MIN.1/8" THREAD DEPTH

12 GAGE STEEL STRIKE REINF.PLATE - PROJECTIONWELDED TO FRAME (6) PLACES

PUNCH AND TAPFOR 12-24 MS(2) PLACES

16 GAGE STRIKE REINFORCEMENT

PLASTER GUARDFORMED AS PARTOF STRIKE REINF.

FIT FOAM FILLEDWEATHERSTRIP TOFRAME AFTER FINISHPAINTING

26 GAGE STEELSNAP-IN PLASTERGUARD

11-206

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataSERIES CF PROFILE WKWEATHERSTRIP - KERF FRAME STRIKE PREPARATION

NOMINAL SIZES

1-3/4” DOOR FRAME, FULL DEPTHHINGE REINFORCEMENT

11-207

TAPPED HOLEFOR #12-24 MS(4) PLACES

1 1"4

4 1"2

1"2

1"2

81"1

1"1 8

1 15"16

1 5"8

5" (NOM)16

(NOM.)

BACKSET

12"

5"16

5"8

7 GAGE HINGE REINFORCEMENT WELDED TO FRAME

AVAILABLE FOR FRAME DEPTHS5-1/2" THRU 10-5/8"

4-1/2" HIGH HINGEAPPLICATION SHOWN

FRAME WIDTHLESS 1/2"

XXX

X

XXX

X

XXX

X

XXXX

"

"18

34

5/8" STOP

1"

2"

1/4" LONG ARC WELDS(3) PLACES PER STRAP

HINGE REINFORCEMENT ANDPLASTER GUARD APPLIEDPER PAGE #11-202

STEEL STRAP

11-208

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataDOOR FRAME HIGH FREQUENCYHINGE REINFORCEMENT STRAP

NOMINAL SIZES

DOOR FRAME MUTES

11-209

9 3/4" MAX.

C OF

STRIKEL

M M

6" ON CENTERM

12" MAX.

12" MAX.

M

M

INSERT BLUNT END OF 3/32" DIAMETER WIREOR TOOL IN HOLE IN CENTER OF MUTE.

MOISTEN CONE PORTION AND INSERT IN HOLE INSTOP OF FRAME, PUSHING SLOWLY WITH CIRCULARMOTION TO ELONGATE MUTE SUFFICIENTLY TOSET IN PLACE.

REMOVE WIRE

1.

2.

3.

DOOR MUTES (SILENCERS) MAINTAIN PROPERSPACE (1/16") BETWEEN DOOR AND FRAMESTOP AND CUSHION DOOR CLOSING. INSERTMUTES INTO FRAME BEFORE FRAME IS INSTALLED INTO WALL TO PREVENT GROUT,PLASTER, ETC. FROM FILLING HOLES.

SINGLE SWING DOUBLE SWING

STANDARD LOCATION OF DOOR MUTES

SINGLE SWING DOOR FRAMES - 3 MUTES DOUBLE SWING DOOR FRAMES - 2 MUTES DUTCH DOOR FRAMES - 4 MUTES

M = MUTE

Fed. Spec. Type 1337A

Note 1Pips are provided forprojection welding. Ifother welding is used,flip Part A over.

A. (12 ga. galv. steel)

B. (16 ga. galv. steel, prime paint)

D. #8-32 x 1/2" UCFHMS (2)

STRIKE FILLER

STRIKE

REINFORCEMENT

PLASTER GUARD

Part B

Tackweld Part E on back ofreinforcement as necessary.

Note 1

RRA/LA shownFlip flop Part Bfor LRA/RA

Center of cutoutand door

Center line of Door Opening Widthand Cutout

HEAD

Part C

Part B

Part A

Tapped for#8-32 MS

Weld Part Ato Head at each side

Part A

Part D

E. Plaster guard (Included on SU and SQ frames only)

RFB AssemblyParts A,B, and D as listedbelow:

C. (16 ga. galv. steel, prime paint)

15/16"

11-210

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataREVERSIBLE FLUSH BOLT PREPARATION

WELDING TYPE T-1 "STITCH WELD at SOFFIT ONLY"Standard KD frame components from stock with corner reinforcements.NO SAWING REQUIRED.

WELDING TYPET-1

(1-1/2" wide and up)

jamb soffit seam.end of the head andwelds located at eachTwo 1/2" long stitch

located in the centerlength stitch weld,One 1/2" (minimum)

WIDE STOP

Wide Stop:

(up to 1-1/2" wide)NARROW STOP

of the soffit.

Narrow Stop

Reference: This corner has a full and continuousbackbend at the head and jambs. It can be usedon frames that cap the wall.

FACE-MITER SEAMIS VISIBLE

STANDARD KD JAMB

STANDARD KD HEAD

1. Assemble frame: Bend tabs after assuring that face-miter seam is "closed" and "tight". Bend corner reinforcement tabs toward inside (toward throat) of frame. Bend rabbet tabs towards outside (toward jamb backbends).

2. Place weld bead as required at the joint of the head and jamb soffits from the backside.

2a. If weld penetration occurs, file smooth.

2b. Spot paint

NOMINAL SIZES

DIE-CUT, DOUBLE-RABBET FRAMEWELDED CORNER ASSEMBLY

11-301

Reference: This corner has a fulland continuous backbend at the headand jambs. It can be used on framesthat cap the wall.WELDING TYPE T-2 "OUTSIDE FACE WELD ONLY"

Standard KD frame components from stock with corner reinforcements.NO SAW CUTTING REQUIRED.

Reference: This corner has a fulland continuous backbend at the headand jambs. It can be used on framesthat cap the wall.

3. Grind an dress smooth bothface-miter seams after welding.

head and jamb, from the outside (Both faces).

11-302

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataDIE-CUT, DOUBLE-RABBET FRAMEWELDED CORNER ASSEMBLY

2. Weld the entire face-miter seam, between

COMPLETELY INVISIBLEFACE-MITER SEAM IS

STANDARD KD HEAD

STANDARD KD JAMB

Standard KD frame components from stock with corner reinforcements.NO SAW CUTTING REQUIRED.

WELDING TYPE T-2 "OUTSIDE FACE WELD and FULL WEB WELD"

4. Weld the entire web seam(including the seams betweenhead and jamb rabbets, stopsand soffits) from the backside,


5. Spot paint

1. Assemble frame: Bend tabs after assuring that face-miter seam is "closed" and "tight" Bend corner reinforcement tabs toward inside (toward throat) of frame. Bend rabbet tabs toward outside(toward jamb backbends) of

2. Weld the entire face-miter seam, between head and jamb, from the outside (both faces).

3. Grind and dress smooth both face-miter seams after welding.

3a. Spot paint

frame.

2

STANDARD KDHEAD

STANDARD KDJAMB

FACE-MITER SEAMIS COMPLETELYINVISBLE

T-3

toward outside(toward jamb backbends) of (toward throat) of frame. Bend rabbet tabs Bend corner reinforcement tabs toward inside that face-miter seam is "closed" and "tight"1. Assemble frame: Bend tabs after assuring

frame.

with a continuous weld bead.

T-2

NOMINAL SIZES

DIE-CUT, DOUBLE-RABBET FRAMEWELDED CORNER ASSEMBLY

11-303


COMPLETELY INVISIBLEFACE-MITER SEAM IS

DIE-CUT HEAD

DIE-CUT JAMB

V-2

Die-cut frame components - VOID OF CORNER REINFORCEMENTSNO SAW CUTTING REQUIRED

WELDING TYPE V-2 " INSIDE FACE WELD ONLY"

2. Weld the entire face-miter seam from the inside.Weld is to penetrate to exterior.

2a. Grind the exterior face and fill as necessary.

rabbet tabs toward outside (toward jamb backbends) face-miter seam is "closed" and "tight". Bend

1. Assemble frame: Bend tabs after assuring that

of frame.

11-304

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataDIE-CUT, DOUBLE RABBET FRAMEWELDED CORNER ASSEMBLY


FACE-MITER SEAM ISCOMPLETELY INVISIBLE

DIE-CUT HEAD

DIE-CUT JAMB

Die-cut frame components - VOID OF CORNER REINFORCEMENTSNO SAW CUTTING REQUIRED.

WELDING TYPE V-3 "INSIDE FACE WELD and FULL WEB WELD"

1. Assemble frame: Bend tabs after assuring that face-miter seam is "closed" and tight. Bend rabbet tabs toward outside (toward jamb backbends) of frame.

2. Weld the entire face-miter seam from the inside. Weld is to penetrate to exterior.

2a. Grind the exterior face and fill as necessary.

3. Dress reworked areas.

4. Weld the entire web seam (including the seams between head and jamb rabbets, stops, and soffits) from the backside with a continuous weld bead.


5. Spot weld.

V-3

42

1a. Clamp the head and jamb at 90˚.

2. Clamp head and jamb at 90˚.

frame sections is 90˚.

11-308

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech Data4” & 6” HOSTPITAL STOPS

CLOSER MOUNTINGREGULAR ARM

JAMBHINGE

RABBETDOOR(1) 1" LONG (APPROX)

STITCH WELD AT EACHEND OF PLATE END OF PLATE

STITCH WELD AT EACH(1) 1" LONG (APPROX)

HINGEJAMB

HEAD

PARALLEL ARMCLOSER MOUNTING

REINFORCEMENT PLATE:14 GAGE MIN. STEEL x 1/3/4" x 14" (1)REINFORCEMENT PLATE: REINFORCEMENT PLATE:

14 GAGE MIN. STEEL x 1/3/4" x 14" (1)Note: If 1-3/4" dimension is too bigto fit stop ..decrease size to suit.

LOCATION OFOPTIONALPLATE, SEE11-402

REINFORCEMENT PLATE:14 GAGE MIN. STEEL x 1/3/4" x 14" (1)REINFORCEMENT PLATE:

END OF PLATESTITCH WELD AT EACH(1) 1" LONG (APPROX) DOOR

RABBET

HINGEJAMB

TOP JAMBCLOSER MOUNTING

to fit stop ...decrease size to suit.Note: If 1-3/4" dimension is too big

14 GAGE MIN. STEEL x 1/3/4" x 14" (2)REINFORCEMENT PLATE:

CLOSER MOUNTINGCORNER BRACKET

JAMBHINGE RABBET

DOOR

(1) 1" LONG (APPROX)STITCH WELD AT EACHEND OF EACH PLATE

14"

STOP

PLACE FLAT AGAINSTINSIDE OF FACE ANDBUTT AGAINST INSIDEOF DOOR RABBET.

AND BUTT AGAINST INSIDEINSIDE OF DOOR SOFFITPLACE FLAT AGAINST

DOORRABBET

OF DOOR STOP

OF DOOR STOP

PLACE FLAT AGAINSTINSIDE OF DOOR SOFFITAND BUTT AGAINST INSIDE

OF HEAD BACKBEND.BUTT AGAINST INSIDEINSIDE OF FACE ANDPLACE FLAT AGAINST

Note: Verify against manufacturer's templatethat size and position of plate satisfyhardware needs.

Note: Do not use withstandard DW plumbanchor . Not recom-mended when dooropening height isless than 7'-'0".

Note: If 1-3/4" dimension is too bigto fit face ...decrease size to suit.

Note: If 1-3/4" dimension is too bigto fit face ...decrease size to suit.

NOMINAL SIZES

CLOSER REINFORCEMENTPLATE TYPE

11-401

14"4" 2" 14"

2" 14"14"

HEAD

HEADHEAD

END OF PLATESTITCH WELD AT EACH(1) 1" LONG (APPROX)

OUTSWING DOOR: SURFACE BOLTSAND REMOVABLE MULLIONS

REINFORCEMENT PLATE:14 GAGE MIN. STEEL x 1/3/4" x 14" (1)

Note: If 1-3/4" dimension is too bigto fit stop ..decrease size to suit.

AND BUTT AGAINST INSIDEINSIDE OF DOOR SOFFITPLACE FLAT AGAINST

DOORRABBET

OF DOOR STOP

Note: Verify against manufacturer's templatethat size and position of plate satisfyhardware needs.hardware needs.

that size and position of plate satisfyNote: Verify against manufacturer's template

INSIDE OF DOOR FACE

RABBETDOOR

PLACE FLAT AGAINST IN-SIDE OF RABBET OPPOSITEDOOR AND BUTT AGAINST

11-401PLATE, SEEOPTIONALLOCATION OF

to fit face ..decrease size to suit.Note: If 1-3/4" dimension is too big


CLOSER MOUNTINGPARALLEL ARM

JAMBHINGE

(1) 1" LONG (APPROX)STITCH WELD AT EACHEND OF PLATE

hardware needs.that size and position of plate satisfyNote: Verify against manufacturer's template

OF DOOR RABBET

RABBETDOOR

PLACE FLAT AGAINSTINSIDE OF FACE ANDBUTT AGAINST INSIDE

to fit face ..decrease size to suit.Note: If 1-3/4" dimension is too big


INSWING DOOR: SURFACE BOLTS

(1) 1" LONG (APPROX)STITCH WELD AT EACHEND OF PLATE

JAMBBOTTOM OF STRIKE

RABBETDOOR

END OF PLATESTITCH WELD AT EACH(1) 1" LONG (APPROX)

REINFORCEMENT PLATE:14 GAGE MIN. STEEL x 1/3/4" x 14" (1)

Note: If 1-3/4" dimension is too bigto fit stop ..decrease size to suit.

PLACE FLAT AGAINSTINSIDE OF DOOR SOFFITAND BUTT AGAINST INSIDEOF DOOR STOP

RIM TYPE PANICDEVICE MOUNTING

14"

14"2" 7"

33-5/16"

40-5/16"

14"

7"

cL

HEADHEAD

CL of opening

L of openingC

HEAD

7"

14"

11-402

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataCLOSER REINFORCEMENTPLATE TYPE

SECTIONFRAME HEAD

1-15/16"RABBET

DOORSIDE

HEAD

CR/HALF

SPOT OR TACKWELDED IN PLACE.

(2) WELDS PER END

REGULAR & PARALLELARM CLOSER MOUNTING

14GA. GALV. STL.

NOMINAL SIZES

HALF-CLOSER REINFORCEMENT

11-403

1-5/8"

5/8"

1-1/2"

1-31/32"

13-7/8"

2" MIN.FACE

4" 13-7/8"

HINGEJAMB

NOMINAL SIZES

JAMB ANCHOR QUANTITIESFOR STANDARD HEIGHT FRAMES

11-500

* Floor anchors may be omitted and replaced with two additional jamb anchors.

Unless otherwise indicated, jamb anchors are normally located on the same center line as the hinge preparations except where interference would occur with hardware reinforcements. Where interference would occur, anchors should be positioned above or below hinge reinforcements and directly opposite on the strike jamb.

For sizes other than listed above, the following guidelines are followed (unless otherwise indicated)...For heights to 6-0: Two jamb anchors per jamb; For heights greater than 6-0 thru 7-6: Three jamb anchors per jamb; For heights greater than 7-6 thru 10-0: Four jamb anchors per jamb; and for each additional 2 feet of height or fraction thereof: One additional jamb anchor per jamb.

ANCHOR TYPE

NEW MASONRY 6 8

8 10 OMIT

2

2 *

6 8 2WOOD STUD

METAL STUD

SOLID PLASTER

LAMINATEDDRYWALL

EXISTING OPENING

QUANTITY

6-8 THRU 7-2 7-10 THRU 10-0

FLOOR ANCHORSPER FRAME

JAMB ANCHORS PER FRAME

*

6 8

2 *6 8

2 *6 8

NOMINAL SIZES

WELDED FLOOR ANCHOR

11-501

3-1/8

1-23/32

1-7/16

1/2

1/21/2

5/16 DIA.HOLES

1-1/2

1-1/2

1/2

DIM A

1" CTCSPACES

5/16 DIA.HOLES

11/16 11/16

DIM A FRAME DEPTH HOLES

3-1/25

6-1/28

4-1/2 to 5-1/45-3/8 to 6-3/46-7/8 to 8-1/48-3/4 to 9-3/4

3568

ONE PIECE ANCHOR SELECTION CHART

All dimensions are in inches. For SI conversion: 1" = 25.4 mm.Anchors for depths outside the above range are made to order.

TWO PIECE ANCHOR

(16 GA. GALV.)(16 GA. COLD ROLLED)

CENTER OF JAMBAND ANCHOR

16 GAGEGALV STEEL

WELDWELD

TWO PIECE APPLICATION ONE PIECE APPLICATION

11-502

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataADJUSTABLE FLOOR ANCHOR

4" TRAVEL

2-1/8"

5/16" DIA.2-1/8"

O.A.

HAT:4-1/4" WIDE x 3/4" LEGSx 5/8" OFFSET @ 3-1/4"LONG

ANGLE:1-1/2" x 6-3/4" @ 2-3/4"LONG

SCREW:#10 x 3/4" THSMS

FLUSH WITHJAMB BOTTOM

Dim A = Depth (-) 1-3/16"(assuming 1/2" backbends)

Dim A

Dim A

Dim A = Depth (-) 3/16"

FLOOR

FLOOR

IMPOST

IMPOST

Note: Anchor is attached to floor attwo places. Mullion or sill is slippedover anchor (fastening is optional).

12 GAGESTEEL

(2) 9/32"DIA. HOLES

Note: Position sill anchorto avoid possible interferencewith sill bracing strap ifpresent.

SILL BRACINGSTRAP

FOR VERTICAL MULLIONS

FOR BASE SILLS

NOMINAL SIZES

SIDELITE FLOOR ANCHOR

11-503

11-504

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataANCHORS FOR NEW MASONRY

1-13/16"

8-1/4"

2"

8"

R 1-1/4"

2-5/16"9-3/8"

2"

MASONRY "T" ANCHOR

WIRE MASONRY ANCHOR

SPOTWELDED

16 GAGEGALV STEEL

DEPTH

6-3/4

7-3/4

8-3/4

4-3/4

5-3/4

DEPTH

5-1/4

4-1/4

4-1/44-3/4 3-3/4

3-3/4

MFGFIELD MODIFIED DEPTH

THROAT RANGE

2 THRU 8-3/4

All dimensions are in inches; forSI conversion, 1" = 25.4 mm.

7 GAGE GALV.STEEL WIRE

- -

44

34

3

44

3

54

1

1

34

4

4 1

334

4

NOMINAL SIZES

MASONRY ANCHORS CONT.EXISTING OPENING ANCHOR

11-505

Available on specialorder only

order onlyAvailable on special

WELDED

YOKE AND STRAP MASONRY ANCHOR

EXISTING OPENING ANCHOR

FOR ALLFRAME DEPTHS

11-506

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataEXISTING OPENINGSTANDARD JAMB ANCHOR

NOMINAL SIZES

EXISTING OPENING ANCHORFOR SPECIAL FACES

11-507

All dimensions are in inches. For SI conversion: 1" = 25.4mm.Dimension A assumes a 5/8 frame stop height.Suggested Rough-opening clearance: 1/4" @ head and jambs.See page 11-506 for jamb punching, spacing, fastener, and floor anchor notes.

EXISTING OPENING/NARROW ANCHOR SIZE CHART

FACE 1 1-1/4 1-1/2 1-3/4 2 2-1/2

DIM A 1-9/16 1-13/16 2-1/16 2-5/16 2-9/16 3-1/16

EXISTING OPENING/NARROW

1

1-1/2

3-1/4

DIM A

1

1-1/4

1/8

11-508

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataWELDED WOOD STUD ANCHOR

5/8

JAMB DEPTHEQUALS WALL

THICKNESSPLUS 1-1/8

3/16

*DIM "X"

MSZ1 ANCHORSPOT WELDEDTO JAMB

SPOT WELDED TOMSZ1 ANCHOR

5/32 DIA. HOLES(2) PLACESEACH STRAP

JAMB

WALL SECTIONWood blocking bycontractor asnecessary.

to stud bycontractor

TOSUITWALL

The wood stud anchor depicted below is shop attached. Unless otherwise designated, a stud anchor willbe attached at each sill in lieu of a floor anchor.

18 GAGESTEEL

WOOD STUD ANCHOR SELECTION CHART

STUD SIZE

2 x 4

2 x 6

DIM "X"

3-1/2

5-1/2

INSTALLATION SEQUENCE1. WALL FRAMING2. DOOR FRAME3. WALL SURFACE MATERIAL

* Or to suit other stud sizes.For stud sizes other than shownbelow: actual stud dimension shouldbe noted. Also, wall board thicknessesshould be shown so that straps canbe properly positioned.

PORTION OF JAMBREMOVED FOR CLARITY

Straps are nailed

STRAP ANCHOR

All dimensions are in inches, forSI conversion, 1" = 25.4 mm.

NOMINAL SIZES

ADJUSTABLE JAMB ANCHORFOR STUD WALLS

11-509

ASSEMBLY DETAIL(END VIEW)

Anchors are adjustable in 1/8"increments within given ranges.

Metal stud similarWood stud shown

FRAMEHOLLOW METAL

FRAME ANCHOR

WALL BOARD

WALL STUD

NAILS OR SCREWS

TYPICAL APPLICATION

FRAME DEPTH: 3-3/4" thru 6-1/4" FRAME DEPTH: 6-1/4" thru 8-3/4"

87

4

5

6

6 14

8

11-510

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataWELDED METAL STUD ANCHOR RECESSED TYPE

5/8

DIM "A"

EQUAL

EQUAL

JAMB

WALL SECTION

The metal stud anchor depicted below is shop attached. Unless otherwise designated, a stud anchor willbe provided for each sill.

18 GAGESTEEL

Stud isscrewedto anchor

If second studis used, attachit after jambis fastened.

2. WALL FRAMING1. DOOR FRAMEINSTALLATION SEQUENCE

3. WALL SURFACE MATERIAL

3-1/2 4-1/2 THRU 5-1/4

8-3/8 THRU 9-3/4

5-3/8 THRU 6-3/4

6-7/8 THRU 8-1/46-1/2

8

5

DEPTH RANGEDIM"A"

FRAME

ZEE ANCHOR (1x1-1/4x1 @ Dim "A" long)SPOT WELDED TO JAMB

MSZ anchor andstop as necessary

clip is welded tox 1 long steel "zee"a 3/4 x 5/8 x 3/4depths over 4 inches,For single rabbet


NOMINAL SIZES

WELDED METAL STUD ANCHORFLUSH TYPE

11-511

DIM "C"DIM "A"

DIM "B"

DIM "B"

Allow 3/16" clearancebetween studand jamb

The metal stud anchor depicted below is shop attached. at sill.

For single rabbetdepths over 4 inches,a 3/4 x 5/8 x 3/4x 1 long steel "zee"clip is welded toMSZ anchor andstop as necessary

Stud isscrewed to anchor

Series BQ shouldbe considered

If second studis used, attachit after jambis fastened.

4-5/85-7/8

7-1/2 2-1/8

1-7/16

13/16

3-1/43

3 5-3/8 THRU 66-1/8 THRU 7-5/8

7-3/4 THRU 9-1/4

DIM"A" "B"

DIM"C"DIM FRAME

DEPTH RANGE

Anchor is normally positioned in the center ofthroat to accommodate equal thicknesses ofwallboard at each side of stud. If wall is notsymmetrical, drawings showing condition shouldbe provided.

INSTALLATION SEQUENCE

1. WALL FRAMING2. DOOR FRAME3. WALL SURFACE MATERIAL

16 GAGESTEEL

Shim


Designate if floor anchor or jamb anchor is desired

5-5/8

3/4

CL

CL

1-1/16

STUDSIZE

9/16

7/32 R.

3/41-5/16

4

1/2" BACKBENDS

BEND HERE FOR ONELAYER OF 1/2" > 5/8"

BEND HERE FOR TWOLAYERS OF 1/2" > 5/8"

FOR 2"FACE

18 GAGEGALV STEEL

NOTEFRAME IS SET-UP

AND JAMBS ANCHOREDBEFORE WALLBOARD IS

INSTALLED.

ANCHORS ARE BENT INFIELD TO THICKNESSOF WALLBOARD. IFWALL FRAME WORK ISSET UP BEFORE DOORFRAME, USE ANADDITIONAL JAMB ANCHORAT SILL INSTEAD OFSILL ANCHOR.

STUD

PLACE

BEND

WALLBOARD

WALLBOARD

TAP-IN

WELD TOJAMB

SILL CLIP ATEACH END AND24" O.C.

JAMB

16 GAGESTEEL

2

FACE

Contractorsnaps closureinto placeafter frame isinstalled.

BEFORE DRYWALLSTUD ANCHOR

CLOSURE CLIP


11-512

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataBEFOR DRYWALL STUD ANCHORAND CLOSURE CLIP

1"

3/32"

NOMINAL SIZES

FRAME SPLINES

11-513

SPLINE APPLICATION

8"

Stitchweld

16 Ga. steel

DEPTH FSPAREWORK

3-7/8" or OVER 334

4-3/4" or OVER 434

5-3/4" or OVER 534

6-3/4" or OVER 634

Frame components should have open ends.Mitered corners prevent spline installationwithout modification of backbend.Allot one spline for every 2 feet of impostheight. Drive spline in from ends, locateapprox. equal distance from one another.

For shipping via common carrier,frame size should not exceed8'-0" in more than one dimension.

SPLINE APPLICATION(For Custom Depths)

NOMINAL SIZES

FRAME INSTALLATIONMASONRY AND STUD WALLS

11-901

DOOR OPG AT HEAD

FRA

ME

DEP

TH

JOBSITE STORAGE: Store frames off the ground on wood runners or skids. Do not storedirectly on the ground. Cover frames with tarpaulin or plastic but do insure that adequate

When frames are to be fully grouted and when plaster or mortar contain "anti-freeze" agents,the inside of the frames should be coated with a bituminous, water-resistant paint by theinstallation contractor.

ventilation is provided to eliminate moisture condensation.

Typical wood spreader must be square and madefrom lumber at least 1" thick. Length of spreaderequals door opening width at the head. Cut clear-ance notches for frame stops as shown. Spreadermust be nearly as wide as frame depth for properinstallation.

The installer should use wood spreaders (asdescribed at right), a carpenters level (thelonger the better), and a carpenters square(the bigger the better). Set the frame inthe desired location. Level head and plumbjambs. Shim under jambs if necessary.

SLOTS FORCORNER TABS

CORNER TABS BEND CORNER TABSTOWARD INSIDE OFFRAME

SLOTS FORJAMB TABS

BEND JAMB TABSTOWARD OUTSIDEOF FRAME

JAMB TABS

HEAD JAMB

CORNERASSEMBLY

Install rubber silencers beforeframe is setup to avoid groutplugging holes.

ASSEMBLY of FRAME

SQUARING THE FRAME SPREADER

PLUMBING FRAME

NOMINAL SIZES

FRAME SPREADER BARS

11-903

This bar is not to be used for installation. A wood spreader is to be used for maintainingproper spacing between jambs. (See the DHI publication "The Installation of CommercialSteel Doors and Steel Frames", "Insulated Steel Doors in Wood Frames", and "Builder'sHardware").

3. SPREADER BAR QUANTITY AND LOCATION

A. All single rabbet frames and double rabbet, single swing frames with depth not exceeding 6 inches: attach (1) spreader bar to the door rabbet. (See Fig. #1)

B. All double rabbet, double swing frames or double rabbet, single swing frames with depth exceeding 6 inches: attach one (1) spreader bar to each frame rabbet (two total).

(see Fig. #2)

4. SPREADER BAR ATTACHMENT

Verify spreader bar length by checking to see that said length is equivalent to the door opening width dimension at head. Place the spreader bar at the bottom of the door opening and tack weld in place. Strength of welds should be such that spreader bar remains in place during transit and also be such that the spreader bar can be removed when required (by means of a sharp hammer blow) without incurring frame damage.

1. SPREADER BAR PROFILE 2. SPREADER BAR LENGTH

Length of spreader bar is equivalent to door opening width dimension.

Fig. #1

DOOR RABBET

SPREADER

JAMB

JAMBSPREADERS

BOTH RABBETS

Fig. #2

X X

X X X

XXX X X

XXXX

X

distributor tech data distributor tech data - ceco door area... · ceco door products distributor...

Documents