dir-300nrub7_user manual_v.1.4.1_14.11.12_en

8/13/2019 DIR-300NRUB7_User Manual_v.1.4.1_14.11.12_EN

1/172

User Manual

DIR-300NRU

Wireless Router with Built-in 4-port Switch

November 2012


2/172

DIR-300NRU Wireless Router with Built-in 4-port Switch

User Manual

ContentsChapter 1. Introduction..........................................5

Contents and Audience.......................................................5Conventions.................................................................5Document Structure..........................................................5

Chapter 2. Overview..............................................6General Information.........................................................6Specifications..............................................................!roduct Appearance.........................................................12

Front Panel..............................................................12

Back Panel...............................................................13

Deliver" !ac#a$e...........................................................1%

Chapter &. Installation and Connection..........................15'efore (ou 'e$in...........................................................15Connectin$ to !C...........................................................16

PC with Ethernet Adapter............................................ .....16

Obtaining IP Address A to!aticall" in O# $indows %P............ ...... ....16

Obtaining IP Address A to!aticall" in O# $indows &............. ...... ....1'

PC with $i(Fi Adapter............................................... .....23

Con)ig ring $i(Fi Adapter in O# $indows %P............................. ..2*

Con)ig ring $i(Fi Adapter in O# $indows &.............................. ..2+

Connectin$ to )e*+*ased Interface..........................................2 )e*+*ased Interface Structure..............................................2,

Savin$ and -estorin$ Settin$s..............................................&2

Chapter %. Confi$urin$ via )e*+*ased Interface..................&%Clic# n Connect............................................................&%

Creating $A, Connection............................................. .....36

PPPoE Connection.......................................................36

Static IP Connection...................................................41

Dynamic IP Connection..................................................45

PPTP or L2TP Connection................................................49PPTP + Static IP or L2TP + Static IP Connection........................53

PPTP + Dynamic IP or L2TP + Dynamic IP Connection......................61

Checking Internet A-ailabilit"...................................... .....6

Con)ig ring $ireless Connection......................................... .6'

Con)ig ring IP/0................................................ .........&

)ireless /etwor# Settin$s )i0ard........................................... 1 irtual Server Settin$s )i0ard............................................. ,

I! Setup )i0ard..........................................................34

Page 2 of 172


3/172


User Manual

Status.....................................................................31,etwork #tatistics...................................................... . 1

CP..................................................................... 2

4o ting /able........................................................... . 3

Clients.................................................................. * /et........................................................................35

$A,...................................................................... +

Creating PPPoE WA Connection..........................................!6

Creating Static IP WA Connection......................................9"

Creating Dynamic IP WA Connection.....................................93

Creating PPTP or L2TP WA Connection...................................96

Creating PPTP + Static IP or L2TP + Static IP WA Connection..........1""

Creating PPTP + Dynamic IP or L2TP + Dynamic IP WA Connection........1"5

5A,.....................................................................11

)i+ i.....................................................................112Co!!on settings.........................................................112

Basic #ettings..........................................................113

#ec rit" #ettings.................................................... ...11*

AC Filter..............................................................12

#tation 5ist......................................................... ...122

$P#.....................................................................123

#$ing WPS %&nction 'ia We()(a$e* Inter ace............................125

#$ing WPS %&nction ,it-o&t We()(a$e* Inter ace........................125

Additional #ettings.............................................. .......12&

$ .....................................................................12'

Client..................................................................131

Advanced..................................................................1&&05A,....................................................................13*

7PnP....................................................................13&

,#....................................................................13

,#.....................................................................1*

4o ting.................................................................1*1

4e!ote Access...........................................................1*3I8 P....................................................................1*+

irewall..................................................................1%6IP Filters..............................................................1*6

0irt al #er-ers...................................................... ...1*'

9.....................................................................1+2

AC Filter..............................................................1+3

Control...................................................................155745 Filter..............................................................1++

Page 3 of 172


4/172


User Manual

S"stem....................................................................153Ad!inistrator Password..................................................1+'

Con)ig ration...........................................................16

#"ste! 5og..............................................................162

Fir!ware 7pgrade..................................................... ...16*,/P Client..............................................................166

/racero te..............................................................16&

/elnet..................................................................16

Chapter 5. Operation Guidelines................................16,Safet" Instructions.......................................................16,

)ireless Installation Considerations......................................16,Connectin$ to Ca*le or DS 7odem..........................................1 4

Chapter 6. A**reviations and Acron"ms..........................1 1

Page 4 of 172


5/172


User ManualIntroduction

CHA !"R 1# IN!R$DUC!I$N

Contents and Audience

This manual describes the router DIR-300NRU and explains how to configure and operate it.

This manual is intended for users familiar with basic networ ing concepts! who create an in-homelocal area networ ! and s"stem administrators! who install and configure networ s in offices.

Conventions

"%am&le Descri&tion

text The bod" text of the manual.

Before You Begin # reference to a chapter or section of this manual.

Quick InstallationGuide

# reference to a document.

C'an(e# name of a menu! menu item! control $field! chec box! drop-downlist! button! etc.%.

1,2.163.4.1 Data that "ou should enter in the specified field.

Information #n important note.

Document Structure

Chapter 1 describes the purpose and structure of the document.

Chapter 2 gi&es an o&er&iew of the router's hardware and software features! describes itsappearance and the pac age contents.

Chapter 3 explains how to install the router DIR-300NRU and configure a () in order to access itsweb-based interface.

Chapter 4 describes all pages of the web-based interface in detail.

Chapter 5 includes safet" instructions and tips for networ ing and connecting additional e*uipment.

Chapter introduces abbre&iations and acron"ms used in this manual.

Page ) of 172


6/172


User Manual$vervie*

CHA !"R 2# $+"R+I",

General Information

The DIR-300NRU de&ice is a wireless router with a built-in +-port switch. It pro&ides a fast andsimple wa" to create a wireless and wired networ at home or in an office.

,ou are able to connect the wireless router DIR-300NRU to a cable or D modem or to a pri&ate/thernet line and use a high-speed Internet connection to successfull" fulfill a wide range of

professional tas s. The built-in +-port switch enables "ou to connect /thernet-enabled computers!game consoles! and other de&ices to "our networ .

Using the DIR-300NRU de&ice! "ou are able to *uic l" create a wireless networ at home or in"our office! which lets "our relati&es or emplo"ees connect to "our wireless networ &irtuall"

an"where $within the operational range of "our wireless networ %. The router can operate as a basestation for connecting wireless de&ices of the standards 01.22b! 01.22g! and 01.22n $at the rateup to 2 04bps%.

The router supports multiple functions for the wireless interface5 se&eral securit" standards $6/(!6(#76(#1%! 4#) address filtering! 6( ! 644.

The wireless router DIR-300NRU includes a built-in firewall. The ad&anced securit" functionsminimi8e threats of hac er attac s! pre&ent unwanted intrusions to "our networ ! and bloc accessto unwanted websites for users of "our #N.

,ou can configure and manage the settings of the wireless router DIR-300NRU &ia the user-friendl"web-based interface $the interface is a&ailable in se&eral languages%.

Page of 172


7/172


User Manual$vervie*

Specifications *

WAN Interface

2 2072009# /-T: /thernet port for cable or D modem or pri&ate /thernet line

LAN Interface

+ 2072009# /-T: /thernet ports

WLAN Interface

I/// 01.22n $up to 2 04bps%

I/// 01.22b7g

Network Functions

6#N connection t"pes

(((o/

tatic I(

D"namic I(

((T(7 1T(

((T(7 1T( ; tatic I(

((T(7 1T( ; D"namic I(

D4( (rox"

RI(

U(n(

upport of = #N

6#N ping respond

? The de&ice features are sub@ect to change without notice. Aor the latest &ersions of the firmware and rele&antdocumentation! &isit www.dlin .ru .

Page . of 172
http://www.dlink.ru/http://www.dlink.ru/


8/172


User Manual$vervie*

Wireless Connection

upported securit" settings

6/(

6(#76(#1 (ersonal

6(#76(#1 /nterprise

4#) filter

4anaging connected stations

(IN and (9) methods of 6(

644 $6i-Ai Bo %

#d&anced settings

upport of client mode

Frequency Range

1+00C1+ 3. 4


9/172


User Manual$vervie*

01.22n $t"pical at room temperature 1 0G%


10/172


11/172


User Manual$vervie*

L)Ds

(ower

Internet

6 #N

+ #N /Ds

ower

/xternal power adapter D) =72K

Reset to Aactor" Defaults button

Operating Temperature

Arom 0 to +0 0) $from 31 to 20+ 0A%

"torage Temperature

Arom -10 to 0G $from -+ to 2+E 0A%

Operating #umi'ity

Arom 20 to E0 non-condensing

"torage #umi'ity

Arom to E non-condensing

Page 11 of 172


12/172


User Manual$vervie*

Product Appearance

Front Panel

Figure 1. Front panel view.

"D Mode Descri&tion

owerSolid green The router is powered on.

No light The router is powered off.

Internet

Solid green The Internet connection is on.

Blinking green

The 6#N interface is acti&e $upstream or downstreamtraffic%.

WLAN

Solid green The router's 6 #N is on.

Blinking greenThe 6 #N interface is acti&e $upstream or downstreamtraffic%.

LAN *+&

Solid green# de&ice $computer% is connected to the rele&ant port!the connection is on.

Blinking greenThe #N port is acti&e $upstream or downstreamtraffic%.

Page 12 of 172


13/172


User Manual$vervie*

Back Panel

Figure 2. Back panel view.

ort Descri&tion

AN 1-4 + /thernet ports to connect computers or networ de&ices.

IN!"RN"!# port to connect to a cable or D modem or to a pri&ate /thernet line$it is recommended to use the cable included in the deli&er" pac age%.

)+ 1A (ower connector.

R" "!

,

# button to restore the factor" default settings and to *uic l" addwireless de&ices to the router's 6 #N $the 6( function%.

To use the 6( function5 with the de&ice turned on! push the button andimmediatel" release it.

To restore the factor" defaults5 with the de&ice turned on! push the button! hold it for 3 seconds! then release it.

The de&ice is also e*uipped with a built-in 6i-Ai antenna.

Page 13 of 172


14/172


15/172


User ManualInstallation and Connection

CHA !"R 3# IN !A A!I$N AND C$NN"C!I$N

Before You Begin

(lease! read this manual prior to installing the de&ice. 4a e sure that "ou ha&e all the necessar"information and e*uipment.

Operating "ystem

)onfiguration of the wireless router DIR-300NRU with a built-in +-port switch $hereinafter referredto as Mthe routerL% is performed &ia the built-in web-based interface. The web-based interface isa&ailable from an" operating s"stem that supports a web browser.

We, -rowser

The following web browsers are recommended5 6indows Internet /xplorer! 4o8illa Airefox! orOpera.

Aor successful operation! Pa&a cript should be enabled on the web browser. 4a e sure thatPa&a cript has not been disabled b" other software $such as &irus protection or web user securit"

pac ages% running on "our computer.

Wire' or Wireless NIC .)t/ernet or Wi+Fi A'apter0

#n" computer that uses the router should be e*uipped with an /thernet or 6i-Ai adapter $NI)%. If"our computer is not e*uipped with such a de&ice! install an /thernet or 6i-Ai adapter prior to usingthe router.

Wireless Connection

6ireless wor stations from "our networ should be e*uipped with a wireless 01.22b! g! or n NI)$6i-Ai adapter%. In addition! "ou should specif" the &alues of ID! channel number and securit"settings defined in the web-based interface of the router for all these wireless wor stations.

Page 1) of 172


16/172



Connecting to PC

PC with Ethernet Adapter

2. 4a e sure that "our () is powered off.

1. )onnect an /thernet cable between an" of #N ports located on the bac panel of the routerand the /thernet port of "our ().

3. )onnect the power cord to the power connector port on the bac panel of the router! then plug the power adapter into an electrical outlet or power strip.

+. Turn on "our () and wait until "our operating s"stem is completel" loaded.

Obtaining IP Address Automatically in OS Windows P

2. )lic the tart button and proceed to the Control anel Net*or5 and InternetConnections Net*or5 Connections window.

1. In the Net*or5 Connections window! right-clic the rele&ant ocal Area Connectionicon and select the ro&erties line in the menu displa"ed.

Figure 3. The Net ork Connections window.

Page 1 of 172


17/172



3. In the ocal Area Connection ro&erties window! on the 6eneral tab! select theInternet rotocol 7!C 8I 9 line. )lic the ro&erties button.

Figure 4. The !ocal Area Connection Properties window.

Page 1. of 172


18/172



+. elect the $btain an I address automaticall: and $btain DN server addressautomaticall: radio buttons. )lic the $; button.

Figure 5. The Internet Protocol "#CP$IP% Properties window.

. )lic the


19/172


20/172



3. In the menu located on the left part of the window! select the C'an(e ada&ter settin(sline.

Figure 7. The Net ork and S&aring Center window.

Page 20 of 172


21/172



+. In the opened window! right-clic the rele&ant ocal Area Connection icon and selectthe ro&erties line in the menu displa"ed.

Figure . The Net ork Connections window.

Page 21 of 172


22/172



. In the ocal Area Connection ro&erties window! on the Net*or5in( tab! select theInternet rotocol +ersion 4 7!C 8I v49 line. )lic the ro&erties button.

Figure !. The !ocal Area Connection Properties window.

Page 22 of 172


23/172



. elect the $btain an I address automaticall: and $btain DN server addressautomaticall: radio buttons. )lic the $; button.

Figure 1". The Internet Protocol 'ersion ( "#CP$IPv(% Properties window.

F. )lic the $; button in the connection properties window.

Now "our computer is configured to obtain an I( address automaticall".

PC with Wi"Fi Adapter

2. )onnect the power cord to the power connector port on the bac panel of the router! then plug the power adapter into an electrical outlet or power strip.

1. Turn on "our () and wait until "our operating s"stem is completel" loaded.

3. Turn on "our 6i-Ai adapter. #s a rule! modern noteboo s with built-in wireless NI)s aree*uipped with a button or switch that turns on7off the wireless adapter $refer to "our ()documents%. If "our () is e*uipped with a pluggable wireless NI)! install the software

pro&ided with "our 6i-Ai adapter.

Page 23 of 172


24/172



Con#iguring Wi"Fi Adapter in OS Windows P

2. )lic the tart button and proceed to the Control anel Net*or5 and InternetConnections Net*or5 Connections window.

1. elect the icon of the wireless networ connection and ma e sure that "our 6i-Ai adapter ison.

Figure 11. The Net ork Connections window.

3. earch for a&ailable wireless networ s.

+. In the opened ,ireless Net*or5 Connection window! select the wireless networ DI-+&44/-8' and clic the Connect button.

#fter that the ,ireless Net*or5 Connection tatus window appears.

!If "ou perform initial configuration of the router &ia 6i-Ai connection! note thatimmediatel" after changing the wireless default settings of the router "ou will need toreconfigure the wireless connection using the newl" specified settings.

Page 24 of 172


25/172



Con#iguring Wi"Fi Adapter in OS Windows !

2. )lic the tart button and proceed to the Control anel window.

1. elect the Net*or5 and 'arin( Center section. $If the )ontrol (anel has the categor"&iew $the Cate(or: &alue is selected from the +ie* b: drop-down list in the top rightcorner of the window%! choose the +ie* net*or5 status and tas5s line under theNet*or5 and Internet section.%

Figure 12. The Control Panel window.

3. In the menu located on the left part of the window! select the C'an(e ada&ter settin(sline.

+. In the opened window! select the icon of the wireless networ connection and ma e sure that"our 6i-Ai adapter is on.

. To open the list of a&ailable wireless networ s! select the icon of the wireless networconnection and clic the Connect !o button or left-clic the networ icon in thenotification area located on the right side of the tas bar.

Figure 13. The noti#ication area o# the ta$k%ar.

Page 2) of 172


26/172



. In the opened window! in the list of a&ailable wireless networ s! select the wireless networDI-+&44/-8' and clic the Connect button.

Figure 14. The li$t o# availa%le network$.

F. 6ait for about 10-30 seconds. #fter the connection is established! the networ icon will bedispla"ed as the signal le&el scale.

!If "ou perform initial configuration of the router &ia 6i-Ai connection! note thatimmediatel" after changing the wireless default settings of the router "ou will need toreconfigure the wireless connection using the newl" specified settings.

Page 2 of 172


27/172



Connecting to )e + ased Interface

6hen "ou ha&e configured "our computer! "ou can access the web-based interface and configureneeded parameters $create a 6#N connection! change the parameters of the wireless networ !specif" the settings of the firewall! etc.%.

2. tart a web browser $see the Before You Begin section! page 2 %.

1. In the address bar of the web browser! enter the I( address of the router $b" default! thefollowing I( address is specified5 1,2.163.4.1 %. (ress the )nter e".

Figure 15. &onnecting to the we%'%a$ed inter#ace o# the ()*'3""N*+ device.

3. On the opened page! enter the username and password for the administrator account in theo(in and ass*ord fields correspondingl" $b" default! the following username and

password are specified5 admin ! admin %. Then clic the "nter lin .

Figure 16. The login page.

If the error MThe page cannot be displayed L $or MUnable to display the page L7MCould not connect to remote server L% occurs upon connecting to the web-based interface of the router! ma e sure that "ou ha&e properl" connected the router to "our computer.

Page 2. of 172


28/172



Right after the first access to the web-based interface "ou are forwarded to the page for changingthe administrator password specified b" default.

Figure 17. The page #or changing the de#ault ad,ini$trator pa$$word.

/nter a new password in the ass*ord and Con>irmation fields $"ou ma" use digits! atinletters $uppercase and7or lowercase%! and characters a&ailable on the e"board%! then clic the avelin .

Remember or write down the new password for the administrator account. In case of losingthe new password! "ou can access the settings of the router onl" after restoring the factor"default settings &ia the hardware R)")T1W " button. This procedure wipes out allsettings that "ou ha&e configured for "our router.

Page 2/ of 172


29/172



)e + ased Interface Structure

#fter successful registration the router's *uic settings page opens.

Figure 1 . The -uick $etting$ page.

The web-based interface of the router is multilingual. elect a needed language from the menudispla"ed when the mouse pointer is o&er the an(ua(e caption. ,ou can change the language ofthe web-based interface in an" menu item.

Figure 1!. &hanging the language o# the we%'%a$ed inter#ace.

#fter selecting the language! the notification on unsa&ed changes will be displa"ed. )lic the ave

icon $ % to sa&e the current language of the web-based interface as the default language.

The *uic settings page displa"s general information on the router and its software $the &ersion andthe date of the firmware! the I( address of the de&ice! the name of the 6 #N! etc.%.

Page 2 of 172


30/172



On the *uic settings page "ou can run a needed 6i8ard! *uic l" get to some pages of the web- based interface! search for a specific page! or switch to the ad&anced settings section.

To upgrade the firmware of the router! left-clic the current firmware &ersion $the right column ofthe ?irm*are version line%. #fter clic ing the line! the :stem 8 ?irm*are u&(rade pageopens $for the detailed description of the page! see the #ir$%are !pgrade section! page 2 + %.

To contact the technical support group $to send an e-mail%! left-clic the support e-mail address $theright column of the u&&ort line%. #fter clic ing the line! the e-mail client window for sending anew letter to the specified address opens.

To edit the router's local interface parameters! left-clic the I( or 4#) address of the local interface$the right column of the AN I line or AN MAC line correspondingl"%. #fter clic ing the line!the page for editing the #N interface opens $for the detailed description of the page! see the &'( section! page 220%.

To configure the router's 6 #N parameters! left-clic the ID of the 6 #N $the right column ofthe ID line%. #fter clic ing the line! the ,i-?i 8 @asic settin(s page opens $for the detaileddescription of the page! see the Basic )ettings section! page 223%.

To configure connection to the Internet! clic the Clic5 n Connect lin in the Net section $for thedetailed description of the 6i8ard! see the Click*n*Connect section! page 3+%.

To configure the router's wireless networ ! clic the ,ireless net*or5 settin(s *iBard lin inthe ,i-?i section $for the detailed description of the 6i8ard! see the +ireless (et%ork )ettings+i,ard section! page F2%.

To configure access from the Internet to a web ser&er located in "our #N! clic the +irtualserver settin(s *iBard lin in the ?ire*all section $for the detailed description of the 6i8ard!see the -irtual )er.er )ettings +i,ard section! page FE%.

To configure the router to use an I(T= set-top box! clic the I !+ settin(s *iBard lin in the I -!+ section $for the detailed description of the 6i8ard! see the I/0- )etup +i,ard section! page0 %.

To configure all parameters of the router independentl" without the 6i8ards! clic the Advancedsettin(s lin in the bottom right corner of the page.

Page 30 of 172


31/172



Figure 2". The advanced $etting$ page.

The pages of the tatus section displa" data on the current state of the router $for the description ofthe pages! see the )tatus section! page 2 %.

The pages of the Net section are designed for configuring basic parameters of the #N interface ofthe router and creating a connection to the Internet $for the description of the pages! see the (et section! page %.

The pages of the ,i-?i section are designed for specif"ing all needed settings of the router'swireless networ $for the description of the pages! see the +i #i section! page 221%.#lso "ou canenable or disable the de&ice's 6 #N directl" from the ad&anced settings page. To enable the

6 #N! select the $n position $ % of the "nable8Disable ,i-?i switch. To disable the

6 #N! select the $>> position $ % of the "nable8Disable ,i-?i switch.

The pages of the Advanced section are designed for configuring additional parameters of therouter $for the description of the pages! see the 'd.anced section! page 233 %.

The pages of the ?ire*all section are designed for configuring the firewall of the router $for thedescription of the pages! see the #ire%all section! page 2+ %.

The pages of the Control section are designed for creating restrictions on access to the Internet $forthe description of the page! see the Control section! page 2 %.

The pages of the :stem section pro&ide functions for managing the internal s"stem of the router$for the description of the pages! see the ) ste$ section! page 2 %.

Page 31 of 172


32/172



#lso "ou can find a specific page &ia search. To do this! enter the name of the page! wholl" or partl"! in the search bar in the top part of the web-based interface page! and then select a neededlin in the search results.

Figure 21. The page di$pla ing the $earch re$ult$.

Saving and ,estoring Settings

Note that "ou should regularl" sa&e the changes of the router's settings to the non-&olatile memor".The router's web-based interface displa"s the notification on unsa&ed changes at the top of the page.

Figure 22. The noti#ication on un$aved change$.

(lace the mouse pointer on the Noti>ications icon $ % to &iew the list of unsa&ed changes andclic the rele&ant lin .

,ou can sa&e the router's settings &ia the top-page menu displa"ed when the mouse pointer is o&erthe :stem caption.

Page 32 of 172


33/172



Figure 23. The top'page ,enu.

)lic the Reboot line if "ou ha&e alread" sa&ed the router's settings.

)lic the ave Reboot line to sa&e new settings and immediatel" reboot the router.

)lic the ave line to sa&e new settings to the non-&olatile memor" and continue configuring thede&ice. #lso "ou can sa&e the de&ice's parameters &ia the ave button on the :stem 8Con>i(uration page.

)lic the @ac5u& line and follow the dialog box appeared to sa&e the configuration $all settings ofthe router% to "our (). #lso "ou can sa&e the router's configuration to "our () &ia the @ac5u&

button on the :stem 8 Con>i(uration page.

)lic the ?actor: line to restore the factor" default settings. #lso "ou can restore the factor"defaults &ia the ?actor: button on the :stem 8 Con>i(uration page.

#lso "ou can restore the factor" default settings &ia the hardware R)")T1W " button. The button

is located on the bac panel of the router next to the power connector.

To restore the factor" default settings! push the button $with the router powere' on % and hold for 3seconds. Then release the button. #ll /Ds of the router should turn off and then turn on again.

6ait for about 30 seconds. Now "ou can access the web-based interface of the router using thedefault I( address! username and password.

6hen "ou ha&e configured all needed settings! clic the o(out line.

Page 33 of 172


34/172


User ManualCon>i(urin( via ,eb-based Inter>ace

CHA !"R 4# C$N?I6URIN6 +IA ,"@-@A "DIN!"R?AC"

Click-n-Connect To configure connection to the Internet! clic the Clic5 n Connect lin in the Net section.

Figure 24. &on#iguring connection to the )nternet.

)onnect the /thernet cable pro&ided b" "our I ( to the 6#N port of the router. =erif" the rele&ant/D $the Internet /D should be on%.

)lic the Ne%t button to continue.

Page 34 of 172


35/172



Figure 25. The page #or $electing the connection t pe.

On the opened page! select the needed choice of the radio button and clic the Ne%t button.

Page 3) of 172


36/172


37/172



Figure 27. &on#iguring ///o0 N connection. The e pert $etting$ ,ode. The .t&ernet $ection.

arameter Descri&tion

Connection name # name for connection for easier identification.

"t'ernet

M!U The maximum si8e of units transmitted b" the interface.

MAC

# 4#) address assigned to the interface. This parameter ismandator" if "our I ( uses 4#) address binding. In the field! enterthe 4#) address registered b" "our I ( upon concluding theagreement.

,ou can clic the Clone MAC Address button $ % to set the4#) address of the networ interface card $of the computer that is being used to configure the router at the moment% as the 4#)address of the 6#N interface.

#lso "ou can set the address of a de&ice connected to the router's#N at the moment. To do this! select the rele&ant &alue from thedrop-down list $the field will be filled in automaticall"%.

Page 3. of 172


38/172



Figure 2 . &on#iguring ///o0 N connection. The e pert $etting$ ,ode. The PPP $ection.


Username # username $login% to access the Internet.

,it'out aut'oriBationelect the chec box if "ou don't need to enter a username and

password to access the Internet.

ass*ord # password to access the Internet.

ass*ord con>irmation The confirmation of the entered password $to a&oid mist"pes%.

ervice name The name of the (((o/ authentication ser&er.

Aut'enticational(orit'm

elect a re*uired authentication method from the drop-down list orlea&e the AU!$ &alue.


;ee& Alive

elect the chec box if "ou want the router to eep "ou connected to"our I ( e&en when the connection has been inacti&e for a specified

period of time. 6hen the chec box is selected! the C intervaland C >ails fields are a&ailable. pecif" the re*uired &alues.

Page 3/ of 172


39/172




Dial on demand

elect the chec box if "ou want the router to establish connection tothe Internet on demand. In the Ma%imum idle time field! specif" a

period of inacti&it" $in seconds% after which the connection should be terminated.

I e%tensionThis option is used b" some I (s. )ontact "our I ( to clarif" if thischec box needs to be enabled.

tatic I AddressAill in the field if "ou want to use a static I( address to access theInternet.

debu(elect the chec box if "ou want to log all data on ((( connectiondebugging.

o" &ass t'rou('elect the chec box if "ou want to allow (((o/ clients of

computers from "our #N to connect to the Internet through this(((o/ connection of the router.

Page 3 of 172


40/172



Figure 2!. &on#iguring ///o0 N connection. The e pert $etting$ ,ode. The /iscellaneous $ection.


Miscellaneous

"nable RI elect the chec box to allow using RI( for this connection.

"nable I6M Multicastelect the chec box to allow multicast traffic from the external

networ $e.g. &ideo streaming% to be recei&ed.

NA!elect the chec box if "ou want one 6#N I( address to be used forall computers of "our #N.

?ire*allelect the chec box to enable protection against #R( and DDoattac s.

in(elect the chec box to allow the router to answer ping re*uests fromthe external networ through this connection. Aor securit" reasons!it is recommended not to select this chec box.


#fter that the page displa"ing all specified settings opens. )lic the A&&l: button to create theconnection or the @ac5 button to specif" other settings.

#fter clic ing the A&&l: button! the page for chec ing the Internet a&ailabilit" opens $see the

Checking Internet '.aila ilit section! page %.

Page 40 of 172


41/172



Static IP Connection

Figure 3". &on#iguring Static )/ N connection.

In the Connection name field! specif" a name for the connection for easier identification.Aill in the I Address and Netmas5 fields.

In the 6ate*a: I address field! enter the I( address of the gatewa" used b" this 6#Nconnection.

In the rimar: DN server field! enter the address of the primar" DN ser&er.

#s a rule! the specified settings are enough to configure a connection of the selected t"pe. If "ouneed to specif" additional settings! open the expert settings mode. To do this! use the switch in the

bottom left corner of the page.

Page 41 of 172


42/172



Figure 31. &on#iguring Static )/ N connection. The e pert $etting$ ,ode. The .t&ernet $ection.



"t'ernet


MAC


,ou can clic the Clone MAC Address button $ % to set the4#) address of the networ interface card $of the computer that is

being used to configure the router at the moment% as the 4#)address of the 6#N interface.


Page 42 of 172


43/172


44/172




in(elect the chec box to allow the router to answer ping re*uests

from the external networ through this connection. Aor securit"

reasons! it is recommended not to select this chec box.)lic the Ne%t button to continue.


#fter clic ing the A&&l: button! the page for chec ing the Internet a&ailabilit" opens $see theChecking Internet '.aila ilit section! page %.

Page 44 of 172


45/172



Dynamic IP Connection

Figure 33. &on#iguring ( na,ic )/ N connection.

In the Connection name field! specif" a name for the connection for easier identification.If "our I ( has pro&ided the addresses of the DN ser&ers! deselect the $btain DN serveraddresses automaticall: chec box and fill in the rimar: DN server field.

#s a rule! the specified settings are enough to configure a connection of the selected t"pe. If "ouneed to specif" additional settings! open the expert settings mode. To do this! use the switch in the

bottom left corner of the page.

Page 4) of 172


46/172



Figure 34. &on#iguring ( na,ic )/ N connection. The e pert $etting$ ,ode. The .t&ernet $ection.



"t'ernet


MAC


,ou can clic the Clone MAC Address button $ % to set the4#) address of the networ interface card $of the computer that is being used to configure the router at the moment% as the 4#)address of the 6#N interface.


Page 4 of 172


47/172



Figure 35. &on#iguring ( na,ic )/ N connection. The e pert $etting$ ,ode. The IP and /iscellaneous$ection$.


I

$btain DN serveraddresses

automaticall:

elect the chec box to configure automatic assignment of DNser&er addresses. If the chec box is selected! the rimar: DNserver and econdar: DN server fields are not displa"ed.

rimar: DN server8

econdar: DN server

/nter addresses of the primar" and secondar" DN ser&ers in therele&ant fields.

+endor ID The identifier of "our I (. Optional .

Miscellaneous





?ire*all elect the chec box to enable protection against #R( and DDoattac s.

Page 4. of 172


48/172









Page 4/ of 172


49/172



PP#P or !0#P Connection

Figure 36. &on#iguring //T/ N connection.

In the Connection name field! specif" a name for the connection for easier identification.In the Username field! enter "our login! and in the ass*ord and ass*ord con>irmationfields Q the password to connect to a remote ser&er.

In the + N server address field! enter the I( or UR address of the ((T( or 1T(authentication ser&er.

#s a rule! the specified settings are enough to configure a protected connection $the =(N tunnel%. If"ou need to specif" additional settings! open the expert settings mode. To do this! use the switch inthe bottom left corner of the page.

Page 4 of 172


50/172



Figure 37. &on#iguring //T/ N connection. The e pert $etting$ ,ode. The 'PN $ection.



+ N

Connect automaticall:elect the chec box to enable auto-start of the connection upon the

boot-up of the router.

Username # username $login% to access the ser&er.


password to access the ser&er.

ass*ord # password to access the ser&er.


+ N server address The I( or UR address of the ((T( or 1T( authentication ser&er.

Page )0 of 172


51/172


52/172



Figure 3 . &on#iguring //T/ N connection. The e pert $etting$ ,ode. The /iscellaneous $ection.


Miscellaneous







#fter clic ing the A&&l: button! the page for chec ing the connection a&ailabilit" opens $see theChecking Internet '.aila ilit section! page %.

Page )2 of 172


53/172



PP#P 1 Static IP or !0#P 1 Static IP Connection

Figure 3!. &on#iguring //T/ Static )/ N connection.

Aill in the I Address and Netmas5 fields.

In the 6ate*a: I address field! enter the I( address of the gatewa" used b" this 6#Nconnection.

In the rimar: DN server field! enter the address of the primar" DN ser&er.

#s a rule! the specified settings are enough to configure a non-protected connection of the selectedt"pe. If "ou need to specif" additional settings! open the expert settings mode. To do this! use theswitch in the bottom left corner of the page.

Page )3 of 172


54/172



Figure 4". &on#iguring //T/ Static )/ N connection. The e pert $etting$ ,ode. The .t&ernet $ection.


"t'ernet


MAC





Page )4 of 172


55/172



Figure 41. &on#iguring //T/ Static )/ N connection. The e pert $etting$ ,ode. The IP and/iscellaneous $ection$.


I

I Address /nter an I( address for this 6#N connection.

Netmas5 /nter a subnet mas for this 6#N connection.

6ate*a: I address /nter an I( address of the gatewa" used b" this 6#N connection.

rimar: DN server8

econdar: DN server


Miscellaneous






Page )) of 172


56/172


57/172



Figure 43. &on#iguring //T/ Static )/ N connection.

In the Connection name field! specif" a name for the connection for easier identification.

In the Username field! enter "our login! and in the ass*ord and ass*ord con>irmation

fields Q the password pro&ided b" "our I (.In the + N server address field! enter the I( or UR address of the ((T( or 1T(authentication ser&er.

#s a rule! the specified settings are enough to configure a protected connection $the =(N tunnel%. If"ou need to specif" additional settings! open the expert settings mode. To do this! use the switch inthe bottom left corner of the page.

Page ). of 172


58/172



Figure 44. &on#iguring //T/ Static )/ N connection. The e pert $etting$ ,ode. The 'PN $ection.



+ N









Page )/ of 172


59/172


60/172



Figure 45. &on#iguring //T/ Static )/ N connection. The e pert $etting$ ,ode. The /iscellaneous$ection.


Miscellaneous




in(

elect the chec box to allow the router to answer ping re*uests from

the external networ through this connection. Aor securit" reasons!it is recommended not to select this chec box.




Page 0 of 172


61/172



PP#P 1 Dynamic IP or !0#P 1 Dynamic IP Connection

Figure 46. &on#iguring //T/ ( na,ic )/ N connection.

If "our I ( has pro&ided the addresses of the DN ser&ers! deselect the $btain DN serveraddresses automaticall: chec box and fill in the rimar: DN server field.

#s a rule! the specified settings are enough to configure a non-protected connection of the selectedt"pe. If "ou need to specif" additional settings! open the expert settings mode. To do this! use theswitch in the bottom left corner of the page.

Page 1 of 172


62/172



Figure 47. &on#iguring //T/ ( na,ic )/ N connection. The e pert $etting$ ,ode. The .t&ernet$ection.


"t'ernet


MAC


,ou can clic the Clone MAC Address button $ % to set the

4#) address of the networ interface card $of the computer that is being used to configure the router at the moment% as the 4#)address of the 6#N interface.


Page 2 of 172


63/172



Figure 4 . &on#iguring //T/ ( na,ic )/ N connection. The e pert $etting$ ,ode. The IP and/iscellaneous $ection$.


I


automaticall:


rimar: DN server8

econdar: DN server



Miscellaneous





?ire*all elect the chec box to enable protection against #R( and DDoattac s.

Page 3 of 172


64/172







Figure 4!. &on#iguring //T/ ( na,ic )/ N connection.

In the Connection name field! specif" a name for the connection for easier identification.

In the Username field! enter "our login! and in the ass*ord and ass*ord con>irmationfields Q the password pro&ided b" "our I (.

In the + N server address field! enter the I( or UR address of the ((T( or 1T(

authentication ser&er.#s a rule! the specified settings are enough to configure a protected connection $the =(N tunnel%. If"ou need to specif" additional settings! open the expert settings mode. To do this! use the switch inthe bottom left corner of the page.

Page 4 of 172


65/172



Figure 5". &on#iguring //T/ ( na,ic )/ N connection. The e pert $etting$ ,ode. The 'PN $ection.



+ N









Page ) of 172


66/172


67/172



Figure 51. &on#iguring //T/ ( na,ic )/ N connection. The e pert $etting$ ,ode. The /iscellaneous$ection.


Miscellaneous








Page . of 172


68/172



Checking Internet A%ailability

On the page! "ou can chec the 6#N connection "ou ha&e created.

Figure 52. &hecking the )nternet availa%ilit .In the Result section! the status of the 6#N connection and possible causes of malfunctions aredispla"ed. To rechec the status of the 6#N connection! enter the I( address or name of a host inthe Address field or lea&e the &alue specified b" default $ "a.ru %. Then clic the Rec'ec5

button.

)lic the @ac5 button to specif" other settings.


#fter clic ing the Ne%t button! the page for configuring wireless connection opens $see the

Configuring +ireless Connection section! page E %.

Page / of 172


69/172



Con#iguring Wireless Connection

On the page! "ou can change the name of "our wireless networ ! specif" a password to it! or disable6i-Ai connections.

Figure 53. &on#iguring the wirele$$ connection.

In the ID field! specif" a new name for the networ $use digits and atin characters%.

In the "ncr:&tion ;e: ; field! enter a e" $a password that will be used to access "ourwireless networ %. Use digits and atin characters. #fter appl"ing this setting! the , A-;8, A2- ; mi%ed authentication t"pe is specified for the router's 6 #N.


)lic the 5i& to ne%t button to disable 6i-Ai connections.

#fter clic ing the Ne%t button or the 5i& to ne%t button! the page for configuring the router touse an I(T= set-top box opens $see the Configuring I/0- section! page F0%.

Page of 172


70/172



Con#iguring IP&'

On the page! "ou can configure the router to use an I(T= set-top box.

Figure 54. The page #or $electing a N port to connect an )/T $et'top %o .On the opened page! select the #N port of the router to which "ou will connect "our I(T= set-top

box.

If in the future "ou need to disconnect "our I(T= set-top box from the specified #N port andconnect to it a computer! start the I !+ settin(s *iBard $for the detailed description of the6i8ard! see the I/0- )etup +i,ard section! page 0 %.

If for accessing the Internet and I(T= ser&ices "our I ( uses &irtual local area networ s withidentifiers $= #N ID%! to configure access to the I(T= ser&ice! proceed to the Advanced 8 + AN

page! create a group of ports with the re*uired &alue of the + AN ID parameter! !rans&arentt"pe! and the port to which the set-top box will be connected $see the -&'( section! page 23+! for adetailed description of the elements from the page%.

)lic the @ac5 button to specif" other settings for "our wireless networ .


)lic the 5i& to ne%t button in order not to appl" the I(T= settings.

On the opened page! clic the @ac5 button to specif" other settings for configuring the router touse an I(T= set-top box.

)lic the ave button to sa&e the specified settings.#fter clic ing the ave button! the *uic settings page opens.

Page .0 of 172


71/172


72/172



In the @asic settin(s section! "ou can change the basic parameters of "our router's 6 #N5MhideL "our wireless networ $ Hide Access oint %! specif" a name for the networ $ ID %!select "our location $ Countr: % and the wireless channel number $ C'annel %! specif" the operatingmode $ ,ireless Mode % and the maximum number of de&ices connected to the wireless networ

$Ma% Associated Clients %.

Figure 56. Ba$ic $etting$ o# the wirele$$ N.


Page .2 of 172


73/172



On the next page! "ou can modif" securit" settings of the 6 #N. 9" default! the $&en networauthentication t"pe with no encr"ption is specified for the 6 #N.

Figure 57. The de#ault $ecurit $etting$.

The default securit" settings do not pro&ide sufficient protection for the 6 #N. (lease!specif" "our own securit" settings for the 6 #N.

Page .3 of 172


74/172



Figure 5 . Network authentication t pe$ $upported % the router.

The router supports the following authentication t"pes5

Aut'entication t:&e Descri&tion

$&enOpen authentication $with 6/( encr"ption for wireless networmodes not supporting 01.22n de&ices%.

'ared

hared e" authentication with 6/( encr"ption . This authenticationt"pe is not a&ailable when on the basic settings page! in the,ireless mode drop-down list! a mode supporting 01.22nde&ices is selected.

, A 6(#-based authentication using a R#DIU ser&er.

, A- ; 6(#-based authentication using a ( .

, A2 6(#1-based authentication using a R#DIU ser&er.

, A2- ; 6(#1-based authentication using a ( .

, A8, A2 mi%ed# mixed t"pe of authentication. 6hen this &alue is selected! de&icesusing the , A authentication t"pe and de&ices using the , A2authentication t"pe can connect to the 6 #N of the router.

, A- ;8, A2- ;mi%ed

# mixed t"pe of authentication. 6hen this &alue is selected! de&ices

using the , A- ; authentication t"pe and de&ices using the, A2- ; authentication t"pe can connect to the 6 #N of therouter.

Page .4 of 172


75/172



The , A ! , A2 ! and , A8, A2 mi%ed authentication t"pes re*uire a R#DIUser&er.6hen the $&en or 'ared &alue is selected! the ," "ncr:&tion settin(s section is displa"ed

$the section is una&ailable for the wireless networ operating modes which support the standard01.22n%5

Figure 5!. The 3pen value i$ $elected #ro, the Net ork Aut&entication drop'down li$t.

Page .) of 172


76/172


77/172



6hen the , A- ; ! , A2- ; ! or , A- ;8, A2- ; mi%ed &alue is selected! the, A "ncr:&tion settin(s section is displa"ed5

Figure 6". The )PA0+PS4 value i$ $elected #ro, the Net ork Aut&entication drop'down li$t.


"ncr:&tion ;e: ;# e" for 6(# encr"ption. The e" can contain digits and7or atincharacters.

, A2 re-aut'entication

The chec box acti&ating preliminar" authentication $displa"ed onl"for the , A2- ; and , A- ;8, A2- ; mi%edauthentication t"pes%.

, A "ncr:&tion #n encr"ption method5 !;I ! A" ! or !;I EA" .

, A rene*alThe time period $in seconds%! at the end of which a new e" for 6(#encr"ption is generated. 6hen the &alue 4 is specified for this field!the e" is not renewed.

Page .. of 172


78/172



6hen the , A ! , A2 ! or , A8, A2 mi%ed &alue is selected! the RADIU settin(s and, A "ncr:&tion settin(s sections are a&ailable5

Figure 61. The )PA0 value i$ $elected #ro, the Net ork Aut&entication drop'down li$t.


, A2 re-aut'entication

The chec box acti&ating preliminar" authentication $displa"ed onl"for the , A2 and , A8, A2 mi%ed authentication t"pes%.

I address The I( address of the R#DIU ser&er.

ort # port of the R#DIU ser&er .

RADIU encr:&tion 5e:The password which the router uses for communication with theR#DIU ser&er $the &alue of this parameter is specified in the

R#DIU ser&er settings%.

, A "ncr:&tion #n encr"ption method5 !;I ! A" ! or !;I EA" .

, A rene*alThe time period $in seconds%! at the end of which a new e" for 6(#encr"ption is generated. 6hen the &alue 4 is specified for this field!the e" is not renewed.


6hen all the steps of configuring the 6 #N are completed! the specified settings are displa"ed onthe page. )hec their correctness and then clic the ave button. #fter that "ou get to the *uicsettings page.

Page ./ of 172


79/172



'irtual Server Settings )i2ard

To create a &irtual ser&er for redirecting incoming Internet traffic to a specified I( address in the#N! clic the +irtual server settin(s *iBard lin in the ?ire*all section.

Figure 62. The page #or adding a virtual $erver.

On the opened page! "ou can specif" the following parameters5


!em&lateelect a &irtual ser&er template from the drop-down list! or selectCustom to specif" all parameters of the new &irtual ser&ermanuall".

Name/nter a name for the &irtual ser&er for easier identification. ,ou can

specif" an" name.

Inter>aceelect a 6#N connection to which this &irtual ser&er will be

assigned.

rivate I

/nter the I( address of the ser&er from the local area networ . Tochoose a de&ice connected to the router's #N at the moment! selectthe rele&ant &alue from the drop-down list $the field will be filled inautomaticall"%.

Remote I /nter the I( address of the ser&er from the external networ .

6hen needed settings are configured! clic the ave button. #fter that "ou get to the *uic settings page.

Page . of 172


80/172



IP#' Setup )i2ard

To configure the router to use an I(T= set-top box! clic the I !+ settin(s *iBard in the I -!+section.

Figure 63. The page #or $electing a N port to connect an )/T $et'top %o .

On the opened page! select the #N port of the router to which "ou will connect "our I(T= set-top box and clic the C'an(e button. #fter that "ou will get to the *uic settings page.

If in the future "ou need to disconnect "our I(T= set-top box from the specified #N port andconnect to it a computer! on the current page deselect the #N port and clic the C'an(e button.

If for accessing the Internet and I(T= ser&ices "our I ( uses &irtual local area networ s withidentifiers $= #N ID%! to configure access to the I(T= ser&ice! proceed to the Advanced 8 + AN

page! create a group of ports with the re*uired &alue of the + AN ID parameter! !rans&arentt"pe! and the port to which the set-top box will be connected $see the -&'( section! page 23+! for adetailed description of the elements from the page%.

Page /0 of 172


81/172



Status

The pages of this section displa" data on the current state of the router5

networ statistics I( addresses leased b" the D


82/172



()CP

The tatus 8 DHC page displa"s the information on computers that ha&e been identified b"hostnames and 4#) addresses and ha&e got I( addresses from the D


83/172



*outing &able

The tatus 8 Routin( table page displa"s the information on routes. The table containsdestination I( addresses! gatewa"s! subnet mas s! and other data.

Figure 66. The Status $ ,outing ta le page.

Page /3 of 172


84/172



Clients

On the tatus 8 Clients page! "ou can &iew the list of de&ices connected to the router and de&icesaccessing its web-based interface.

Figure 67. The Status $ Clients page.

Aor each de&ice the following data are displa"ed5 the I( address! the 4#) address! and theinterface to which the de&ice is connected.

Page /4 of 172


85/172


86/172


87/172


88/172









ervice name The name of the (((o/ authentication ser&er.

Aut'entication

al(orit'm

elect a re*uired authentication method from the drop-down list or

lea&e the AU!$ &alue.


;ee& Alive

elect the chec box if "ou want the router to eep "ou connected to"our I ( e&en when the connection has been inacti&e for a specified

period of time. 6hen the chec box is selected! the C intervaland C >ails fields are a&ailable. pecif" the re*uired &alues.

Dial on demand

elect the chec box if "ou want the router to establish connection to

the Internet on demand. In the Ma%imum idle time field! specif" a period of inacti&it" $in seconds% after which the connection should be terminated.

I e%tensionThis option is used b" some I (s. )ontact "our I ( to clarif" if thischec box needs to be enabled.

tatic I AddressAill in the field if "ou want to use a static I( address to access theInternet.

debu(elect the chec box if "ou want to log all data on ((( connection

debugging.

o" &ass t'rou('elect the chec box if "ou want to allow (((o/ clients of

computers from "our #N to connect to the Internet through this(((o/ connection of the router.

Page // of 172


89/172



Figure 71. The page #or creating a new connection. The /iscellaneous $ection.


Miscellaneous







6hen all needed settings are configured! clic the ave button.

Page / of 172


90/172



Creating Static IP )AN Connection

To create a connection of the tatic I( t"pe! clic the Add button on the Net 8 ,AN page. On theopened page! select the tatic I &alue from the Connection !:&e drop-down list and specif"the needed &alues.

Figure 72. The page #or creating a new connection. The General settings and .t&ernet $ection$.


6eneral settin(s

ort# ph"sical or &irtual interface to which the new connection will beassigned.

Name # name for connection for easier identification.

"nable elect the chec box to enable the connection.

Direction The direction of this connection.

"t'ernet


Page 0 of 172


91/172




MAC

# 4#) address assigned to the interface. This parameter ismandator" if "our I ( uses 4#) address binding. In the field! enter

the 4#) address registered b" "our I ( upon concluding theagreement.



#lso "ou can set the address of a de&ice connected to the router's#N at the moment. To do this! select the rele&ant &alue from the

drop-down list $the field will be filled in automaticall"%.

Figure 73. The page #or creating a new connection. The IP and /iscellaneous $ection$.

Page 1 of 172


92/172




I

I Address /nter an I( address for this 6#N connection.

Netmas5 /nter a subnet mas for this 6#N connection.

6ate*a: I address /nter an I( address of the gatewa" used b" this 6#N connection.

rimar: DN server8

econdar: DN server


Miscellaneous







from the external networ through this connection. Aor securit"reasons! it is recommended not to select this chec box.


Page 2 of 172


93/172



Creating Dynamic IP )AN Connection

To create a connection of the D"namic I( t"pe! clic the Add button on the Net 8 ,AN page. Onthe opened page! select the D:namic I &alue from the Connection !:&e drop-down list andspecif" the needed &alues.

Figure 74. The page #or creating a new connection. The General settings and .t&ernet $ection$.


6eneral settin(s

ort# ph"sical or &irtual interface to which the new connection will beassigned.



Direction The direction of this connection."t'ernet


Page 3 of 172


94/172




MAC

# 4#) address assigned to the interface. This parameter ismandator" if "our I ( uses 4#) address binding. In the field! enter

the 4#) address registered b" "our I ( upon concluding theagreement.



#lso "ou can set the address of a de&ice connected to the router's#N at the moment. To do this! select the rele&ant &alue from the

drop-down list $the field will be filled in automaticall"%.

Figure 75. The page #or creating a new connection. The IP and /iscellaneous $ection$.

Page 4 of 172


95/172




I


automaticall:


rimar: DN server8

econdar: DN server



Miscellaneous







from the external networ through this connection. Aor securit"reasons! it is recommended not to select this chec box.


Page ) of 172


96/172



Creating PP#P or !0#P )AN Connection

To create a connection of the ((T( or 1T( t"pe! clic the Add button on the Net 8 ,AN page. Onthe opened page! select the rele&ant &alue from the Connection !:&e drop-down list and specif"the needed &alues.

Figure 76. The page #or creating a new connection. The General settings $ection.


6eneral settin(s

ort ea&e the auto &alue.



Direction The direction of this connection.

Page of 172


97/172

DIR-300NRU

dir-300nrub7_user manual_v.1.4.1_14.11.12_en

Documents