dilo valvesandconnections
TRANSCRIPT
-
8/11/2019 DILO Valvesandconnections
1/138
DILO.Sustainably tight.
Valves and connections for SF6
Madein
Germany
-
8/11/2019 DILO Valvesandconnections
2/138
-
8/11/2019 DILO Valvesandconnections
3/13833
Table of contents
Page
General 04 09
Mounting instructions with torque table 10 14
DILO couplings for SF6-switchgear 15 70
Couplings DN6 15 24
Couplings DN7 25 30
Couplings DN8 31 40
Couplings DN12 41 54
Couplings DN20 55 66
Couplings DN40 67 72
DILO soldering units 73 80
DILO ball valves 81 86
DILO hoses 87 94
DILO transition pieces and adapters 95 122
DILO SF6bottle connections 123
138
C 3099-03
-
8/11/2019 DILO Valvesandconnections
4/138
General
DILO offers the widest valves and
couplings product range in the world.
Whether for medium voltage switch-
gear, high voltage switchgear or
gas-insulated lines (GIL) our products
always meet your requirements.
When using the DILO coupling systema leak rate of better than 1 x 10 -8mbar
l/sec. is achieved corresponding to
less than 1 cm3in 30 years.
The DILO sealing principle prevents
the loss of SF6gas and moisture from
penetrating the SF6gas system. DILO
couplings will eliminate the loss of
SF6gas by incorrect gas handling.
Thanks to their reliability, quality and
durability DILO couplings are the
worlds most widely used connectingsystem for SF6switchgear.
C 3099-03
General
The DILO seal principle 05
Explanation of DILO-pressure stages 06
Surface treatment and cleaning 07
Quality assurance 08
Symbols for valves and ttings 09
4
-
8/11/2019 DILO Valvesandconnections
5/1385
The DILO seal principle
DILO is a seal principle without intermediate
seal in the form of groove and tongue with littledepth of immersion. This principle guarantees
permanent tightness at high static and dynamic
alternating stresses which might result from
vacuum and pressure in connection with high
temperatures and vibrations inside the tubing
systems.
Sealing in accordance with the DILO principle is
effected by direct contact of the sealing prolesof the groove and tongue parts. The different
radii of curvature of groove and tongue are in a
certain relation to each other.
Thus, two ring-shaped sealing areas are produ-
ced which create high stability.The additional braking surface prevents plastic
deformations at the ring-shaped sealing areas.
DILO ttings are easy to assemble and requireno maintenance. They can loosened and re-
connected as often as desired. Thus, the re-use
of the DILO seal is guaranteed. Due to the little
depth of immersion of DILO groove and tongue
the tubes can be immediately pulled out late-
rally after loosing the clamping nut.
C 3099-03
Advantages of application
Self-closing coupling system
Pressure and vacuum-tight even when
coupling and uncoupling
Permanent tightness even when frequently
connected and disconnected
Applicable up to PN 64 bar
Suitable for temperatures from
-40 C to +80 C
Direct connection to DILO service carts
without adapter
Available in different materials even for
outdoor switchgear
DILO couplings allow a connection to be made
by simply screwing the two coupling parts to-
gether. Before the metal to metal seal closes the
pressure and vacuum tight coupling is sealed
inside by means of an O-ring. When loosening
the coupling parts again the same O-ring pre-
vents gas loss whilst the self seal valves close.
closed couplingopen coupling
The DILO seal principle
-
8/11/2019 DILO Valvesandconnections
6/138
Explanation of DILO-pressure stages
C 3099-03
Series ML1 Valves Accessories Hoses
Pressure stage up to PN64 PN50 / 64
DILO-Type explanation
Explanation of abbreviations used in our catalogue
ML Soldering-stub unions with metric connecting dimensions
Illustration of different structural shapes of DILO-soldering unions
A Soldering union
B Screw-in stub-soldering union
M Gauge connecting union
Material No. DIN Material designation DILO material code letter
1.4571 X6CrNiMoTi17-12-2 C
CW614N CuZn39Pb3 P
EN AW-6082 EN AW-ALSi1MgMn T
1.4305 X10CrNiS189 ECW713R CuZn37Mn3Al2PbSi H
Material standards
6
General
-
8/11/2019 DILO Valvesandconnections
7/1387
Surface treatment and cleaning
C 3099-03
Before dispatch or storage, the nished valves and ttings must be treated as follows:
austenitic material is cleaned
brass material is cleaned
aluminium material is anodised, the thread is lubricated with Molykote
Version
Version of the screw-in stub with O-ring sealing (can also be supplied in special design with edge acc.
to DIN 3852 form B).
Design of the screw-in holes for Whitworth-pipe threads as well as for the isometric thread according
to DIN 3852.
O-ring and rubber seal
For all coupling parts an EPDM rubber seal is used as sealing material.
Packing
Parts are all hermetically sealed in PVC to ensure they are kept free of dust and dirt. The unions are
protected against damage by plastic caps.
Soldering process
DILO-soldering unions can be soldered by the well-known autogenous soldering techniques.
Technical data of threads
Type of thread Standards Code designation Illustration
Metric thread DIN 13thread angle 60
M
Whitworth thread DIN/ISO 228thread angle 55
G
-
8/11/2019 DILO Valvesandconnections
8/138C 3099-03
Quality assurance
Quality assurance takes the rst place within the
DILO-organization. Our approved and authorizedexperts permanently check the material careful-
ly. The entire raw material is ordered according
to DILO approval-/ order regulations. Thus it is
guaranteed that all necessary tests have been
carried out which is conrmed in test certicatesaccording to EN 10204 (3.1).
By marking of the raw materials and nished
products, the identity of materials is guaranteed.Our ttings are TV-approved. Furthermore acerticate according to ISO 9001:2008 is availa-ble.
Approvals and tests
DILO products have been approved by internati-
onal classication organisations such as:
Certication according to ISO 9001:2008
HP0 approval as pressure equipment
manufacturer
Production control in accordance witch
EC 97/23 regulations
CERTIFICATEThe Certification Body
of TV SD Management Service GmbH
certifies that
Dilo Armaturen- und Anlagen GmbHFrundsbergstrae 36
D-87727 Babenhausen
has established and appliesa Quality Management System for
Development, Production and Salesof High Pressure and Vacuum Fittings,
SF6Maintenance- and Measuring Devices.
An audit was performed, Report No.70015247
Proof has been furnished that the requirementsaccording to
ISO 9001:2008
are fulfilled. The certificate is valid until 2015-10-11
Certificate Registration No. 12 100 4355 TMS
Munich, 2012-10-18 QMS-TGA-ZM-07-92
8
General
-
8/11/2019 DILO Valvesandconnections
9/1389
Symbols for valves and ttings
C 3099-03
Soldering stub soldering-union Blanking disk
Gauge connection union
Screw-in stub-soldering union
Coupled coupling
Coupling halfs
Hose
Transition piece
Ball valve
-
8/11/2019 DILO Valvesandconnections
10/138
Mounting instructions
C 3100-03
General
Specify the pipe lenghts exactly and cut off rectangularly.
Burr the pipe extremity and clean it metallically bright.
Apply the soldering ux where soldering is to be carried out.
When soldering, use the auxiliary means recommended by DILO and observe the instructions of the
soldering materials supplier.
Do not touch the soldered parts until the solder has solidied and cooled down (Do not quench the soldering area with water).
Remove the soldering material by rinsing with water and by pickling is.
Dry union before mounting.
When mounting only use the connecting components not being damaged by impacts or by overowed soldering material.
It must be strictly observed that the tubing system is tension-free supported and that the tubing
sections align to each other. Possible divergences can be straightened with the DILO straightening tool.
Before nal mounting, check that all DILO-groove and tongue parts are clear of impurities.
In order to reduce the friction, the tube unions should be greased with suitable grease at the threads
and contact surfaces of the clamping nut, especially when made of austenitic materials. Thus the torque
is better converted into axial force and galling of the threads is avoided. When selecting the grease,
observe the operating temperatures, the media, the corrosive degree and the materials.
A fast and strong tightening of the clamping nut guarantees perfect tightness.
The standard version of the screw-in stub of the DILO screw-in unions is equipped with O-ring
sealing.
For mounting of the DILO screw-in unions we recommend the use of soft metal seals for sealing of
the screw-in stub according to DIN 3852 form B , e.g. copper plates opposite the housing or the block.
When all these instructions are observed the mounting will be simple and time-saving. Pipes which
are too short or not precisely aligned will require extra work.
10
Mounting instructions
-
8/11/2019 DILO Valvesandconnections
11/13811
Mounting instructions
C 3100-03
Mounting illustration:
1. Rectangularly saw off the pipes 2. Deburring of the pipe extremitiesinside and outside
3. Clean to a bright metallic nish 4. Apply the soldering ux on the pipe
5. Apply the soldering ux at the part to
be soldered
6. Use of auxiliary materials
-
8/11/2019 DILO Valvesandconnections
12/138
Mounting instructions
C 3100-03
7. Observe the instructions of thesoldering materials supplier
8. Before assembling clean the DILO tongue and groove part
10. Lubricating points at a DILO tube
union
9. Lubricate with appropriate lubricants
11. Tighten fast and strongly the
clamping nut by counteracting force
according to torque table
12. A screw in plug is sealed into a
housing or block with an O ring or
copper seal ring.
12
Mounting instructions
-
8/11/2019 DILO Valvesandconnections
13/13813
Mounting example
C 3100-03
Screw-in stub with O-ring sealing
Torque see torque diagram
Screw-in thread
Screw-in hole see table
Make screw-in hole according to DIN 3852 form X
Use milling cutter for tight seat
DN d4 d7 d8 a1 b1 W
8 M16 x 1,5
G 3/8 A
26 27 1,5 14 0,1
12 G 1/2 A 36 37 2,5 16 0,1
20 M33 x 2G 1 A
49 50 2,5 20 0,2
40 G 1 1/2 A 65 66 2,5 24 0,2
Milling cutter
(on request)
Order No.: 3-216-...
-
8/11/2019 DILO Valvesandconnections
14/138
Torque table
C 3100-03
DILO profile connection
Size of jaw Material Torque Nm
24 AL 40
24 Stainless steel / Brass 40
32 AL 62
32 Stainless steel / Brass 77
41 AL 88
41 Stainless steel / Brass 120
50 AL 110
50 Stainless steel / Brass 140
65 Stainless steel / Brass 150
Screw-in thread
Screw-in thread Material Torque Nm
G1/4 AL 15
G3/8 AL 40
G3/8 Stainless steel / Brass 40
G1/2 AL 68
G1A AL 120
G1A Stainless steel / Brass 130
G1 AL 120
G1 Brass 140
M16x1,5 AL / Stainless steel / Brass 40
M33x2 AL 120
M33x2 Stainless steel / Brass 130
Coupling 3-408-R.. Torque 15 Nm
Coupling 3-888-R.. Torque 15 Nm
Coupling DN40 Torque 80 Nm
Covering caps
Size of jaw Torque Nm
24 20
32 40
50 40
14
Mounting instructions
-
8/11/2019 DILO Valvesandconnections
15/13815
DILO couplings DN6
The coupling allows to establish a
connection by simply fitting both
coupling parts into each other. Before
load relieving of the coupling seats
the pressure- and vacuum tight cou-
pling is sealed inside with an O-ring
during the coupling process. The cou-
pling is forced to be open in coupled
position. If both coupling sides are
separated again the sealing seats shut
off automatically.
All couplings are temperature-resis-
tant from -40 C to +80 C.
The suitable connecting parts for DILO
couplings must be ordered separately.
DILO couplings DN6
3-408-R005 Coupling groove part /
BG PN10 DN6
16
3-408-R006 Flange coupling PN10 DN6 17
3-408-R009 Gauge connecting piece DN6 18
3-408-R007 Covering cap DN6 183-408-R001 Coupling tongue part PN10 DN6 19
6-1161-R013 Coupling tongue part PN10 DN6with connecting coupling formeasuring device
20
3-408-R021/R022 Soldering stub connection DN16 21
3-408-R020 Gauge connecting coupling DN6 21
3-419-R004 Transition piece to DN8
connections
22
3-419-R003 Adapter piece 23
C 3101-04
-
8/11/2019 DILO Valvesandconnections
16/138
BG PN10 DN6
Coupling groove part
Order No.: 3-408-R005 T
Material:AL
C 3101-04
Suitable connectingparts
3-408-R001
3-408-R007
3-408-R020
3-408-R021/22
Spare O-ringOrder No. 1-05-0057-R087
16
DILO couplings DN6
-
8/11/2019 DILO Valvesandconnections
17/13817
PN10 DN6
Flange coupling
Other anges are available on request.
Order No.: 3-408-R006 T
Material:AL
C 3101-04
Suitable connectingparts
3-408-R001
3-408-R007
3-408-R020
3-408-R021/22
Spare O-ringOrder No. 1-05-0057-R084
-
8/11/2019 DILO Valvesandconnections
18/138
PN10 DN6
Gauge connecting piece
Order No.: 3-408-R009 T
Material:AL
C 3101-04
Order No.: 3-408-R007 TMaterial: AL
PN10 DN6
Covering cap
Spare O-ringOrder No. 1-05-0057-R086
Spare O-ringOrder No. 1-05-0057-R084
18
DILO couplings DN6
-
8/11/2019 DILO Valvesandconnections
19/13819
PN10 DN6
Coupling tongue part
Order No.: 3-408-R001 T
Material:AL
C 3101-04
Suitable connectingparts
3-408-R005
3-408-R006
Suitable connectingparts
3-408-R023
3-408-R021/22
3-408-R020
3-419-R004
Spare O-ringOrder No. 1-05-0057-R084
-
8/11/2019 DILO Valvesandconnections
20/138
PN10 DN6
Coupling tongue partwith connecting coupling for measuring device
Order No.: 6-1161-R013
Material:AL / Brass
C 3101-04
Suitable connectingparts
3-408-R005
3-408-R006
Suitable connectingparts
hose formeasuring device
20
DILO couplings DN6
-
8/11/2019 DILO Valvesandconnections
21/138
-
8/11/2019 DILO Valvesandconnections
22/138
PN10 DN6
Transition piece to DN8 connections
DILO couplings DN6
Order No.: 3-419-R004
Material:Stainless steel / Brass
C 3101-04
Spare O-ringOrder No. 1-05-0057-R084
22
-
8/11/2019 DILO Valvesandconnections
23/13823
PN10 DN6
Adapter piece
C 3101-04
Order No.: 3-419-R003
Material:Stainless steel / Brass
-
8/11/2019 DILO Valvesandconnections
24/13824
-
8/11/2019 DILO Valvesandconnections
25/13825
DILO couplings DN7
The plug connection allows to esta-
blish a connection by simply fitting
both coupling parts into each other.
Before load relieving of the coupling
seats the pressure- and vacuum tight
coupling is sealed inside with an O-
ring during the coupling process. The
coupling is forced to be open in coup-
led position. If both coupling sides are
separated again the sealing seats shut
off automatically.
All couplings are temperature-resis-
tant from -40 C to +80 C.
The suitable connecting parts for DILO
couplings must be ordered separately.
DILO couplings DN7
3-308-R003 Plug connection groove part PN30 DN7 26
3-308-R016 Covering cap for plug connection
groove part PN30 DN7
27
3-308-R002 Plug connection tongue part PN30 DN7 28
6-11161-R015 Plug connection tongue part PN30 DN7with connecting coupling for
measuring device
29
3-308-R006 Covering cap for plug connection
tongue part PN30 DN7
30
C 3102-02
-
8/11/2019 DILO Valvesandconnections
26/138
PN30 DN7
Plug connection groove part
Order No.: 3-308-R003 T
Material:AL
C 3102-02
Suitable connectingparts
3-308-R002
3-308-R016
Spare O-ringOrder No. 1-05-0057-R016
26
DILO couplings DN7
-
8/11/2019 DILO Valvesandconnections
27/13827
PN30 DN6
Covering cap for plug connection groove part
Order No.: 3-308-R016 T
Material:AL
C 3102-02
Suitable connectingparts
3-308-R003
-
8/11/2019 DILO Valvesandconnections
28/138
-
8/11/2019 DILO Valvesandconnections
29/13829
PN30 DN7
Plug connection tongue partwith connecting coupling for measuring device
Order No.: 6-1161-R015
Material:AL
C 3102-02
Suitable connectingparts
3-308-R003
3-308-R006
Suitable connectingparts
hose formeasuring device
-
8/11/2019 DILO Valvesandconnections
30/138
PN30 DN7
Covering cap for plug connection tongue part
DILO couplings DN7
Order No.: 3-308-R006
Material:PVC
Suitable connectingparts
3-308-R002
C 3102-0230
-
8/11/2019 DILO Valvesandconnections
31/13831
DILO couplings DN8
The coupling allows to establish a
connection by simply fitting both
coupling parts into each other. Before
load relieving of the coupling seats
the pressure- and vacuum tight cou-
pling is sealed inside with an O-ring
during the coupling process. The cou-
pling is forced to be open in coupled
position. If both coupling sides are
separated again the sealing seats shut
off automatically.
All couplings are temperature-resis-
tant from -40 C to +80 C.
In special version these couplings are
also available for a temperature range
of -60 C to +80 C.
The suitable connecting parts for DILO
couplings must be ordered separately.
DILO couplings DN8
VK/A-02/8 Coupling groove part / A PN64 DN8 32
VK/B(G)-03/8 Coupling groove part PN64 DN8
with O-ring
33
SK-272-R001 Flange coupling PN64 DN8 34
SK-272-R003 Flange coupling PN64 DN8 353-778-R001 Flange coupling PN64 DN8
with 2-hole ange36
VK/KN-04/8 Covering cap fr coupling groove
part PN64 DN8
37
VK/F-02/8 Coupling tongue part PN64 DN8 38
6-1161-R011 Coupling tongue part PN64 DN8
with connecting coupling for
measuring device
39
SK-372-R020/
R021
Gauge connecting coupling
PN64 DN8
40
C 3103-02
-
8/11/2019 DILO Valvesandconnections
32/138
A PN64 DN8
Coupling groove part
C 3103-02
Suitable connectingparts
SK-372-R...
VK/F-02/8
VK/KN-04/8
Suitable connectingparts
SM...
GS...
ML1-AD10-1ML1-AD10-2
3-251-R001
Order No. Material
VK/A-02/8 T AL
VK/A-02/8 E Stainless steel
VK/A-02/8 P Brass
32
DILO couplings DN8
-
8/11/2019 DILO Valvesandconnections
33/13833
PN64 DN8
Coupling groove part with O-ring
In special version the screw-in thread can also supplied withsealing edge acc. to DIN 3852 form B.
C 3103-02
Suitable connectingparts
SK-372-R...
VK/F-02/8
VK/KN-04/8
Spare O-ringOrder No. 1-05-0057-R016
d4 Order No. Material
M16 x 1,5 VK/B-03/8 T AL
M16 x 1,5 VK/B-03/8 E Stainless steel
M16 x 1,5 VK/B-03/8 H Brass
G 3/8 A VK/BG-03/8 T AL
G 3/8 A VK/BG-03/8 E Stainless steel
G 3/8 A VK/BG-03/8 H Brass
-
8/11/2019 DILO Valvesandconnections
34/138
PN64 DN8
Flange coupling
Order No.: SK-272-R001 T
Material:AL
C 3103-02
Other anges are available on request.
Suitable connectingparts
SK-372-R...
VK/F-02/8
VK/KN-04/8
Spare O-ringOrder No. 1-05-0057-R084
34
DILO couplings DN8
-
8/11/2019 DILO Valvesandconnections
35/13835
PN64 DN8
Flange coupling
Other anges are available on request.
Order No.: SK-272-R003 T
Material:AL
C 3103-02
Suitable connectingparts
SK-372-R...
VK/F-02/8
VK/KN-04/8
-
8/11/2019 DILO Valvesandconnections
36/138
PN64 DN8
Flange coupling with 2-hole ange
Order No.: 3-778-R001 T
Material:AL
C 3103-02
Other anges are available on request.
Suitable connectingparts
SK-372-R...
VK/F-02/8
VK/KN-04/8
Spare O-ringOrder No. 1-05-0057-R125
36
DILO couplings DN8
-
8/11/2019 DILO Valvesandconnections
37/13837
PN64 DN8
Covering cap for coupling groove part
C 3103-02
Suitable connectingparts
3-778-R001
SK-272-R001 / R003
VK/A-02/8
VK/B-03/8VK/BG-03/8
Spare O-ringOrder No. 1-05-0057-R132
Order No. Material
VK/KN-04/8 T AL
VK/KN-04/8 E Stainless steel
-
8/11/2019 DILO Valvesandconnections
38/138
PN64 DN8
Coupling tongue part
C 3103-02
Suitable connectingparts
3-778-R001
SK-272-R001 / R003
VK/A-02/8
VK/B-03/8VK/BG-03/8
Suitable connectingparts
SM...
GS...
ML1-AD10-1ML1-AD10-2
3-251-R001
Spare O-ring
Order No. 1-05-0057-R024
Order No. Material
VK/F-02/8 T AL
VK/F-02/8 E Stainless steel
VK/F-02/8 P Brass
38
DILO couplings DN8
-
8/11/2019 DILO Valvesandconnections
39/13839
PN64 DN8
Coupling tongue partwith connecting coupling for measuring device
Order No.: 6-1161-R011
Material:Brass
C 3103-02
Suitable connectingparts
3-778-R001
SK-272-R001 / R003
VK/A-02/8
VK/B-03/8VK/BG-03/8
Suitable connectingparts
hose formeasuring device
-
8/11/2019 DILO Valvesandconnections
40/138
PN64 DN8
Gauge connecting coupling
DILO couplings DN8
Suitable connectingparts
3-778-R001
SK-272-R001
VK/A-02/8
VK/B-03/8VK/BG-03/8
Suitable connectingparts
Gauge withconnecting thread
G A
Description
The gauge connecting coupling serves as connecting piece to a coupling
groove part DN8. When coupling, a pin in the gauge connecting coupling
opens the ow of the opposite coupling groove part (forced opening). Thisallows to read the present operating pressure on the screwed-in gauge.
When disconnecting, the concial nipple of the groove part is closed by
spring load (pressure and vacuum tight). If the gauge connecting coupling
is not connected the gauge shows zero pressure. The connecting coup-
ling allows to install the gauge in any required position (rotatable 360).
Spare O-ringOrder No. 1-05-0057-R225
Spare O-ringOrder No. 1-05-0057-R024
C 3103-02
Order No. Material
SK-372-R020 P Brass
SK-372-R021 C Stainless steel
40
-
8/11/2019 DILO Valvesandconnections
41/13841
DILO couplings DN12
The coupling allows to establish a
connection by simply fitting both
coupling parts into each other. Before
load relieving of the coupling seats
the pressure- and vacuum tight cou-
pling is sealed inside with an O-ring
during the coupling process. The cou-
pling is forced to be open in coupled
position. If both coupling sides are
separated again the sealing seats shut
off automatically.
All couplings are temperature-resis-
tant from -40 C to +80 C.
In special version these couplings are
also available for a temperature range
of -60 C to +80 C.
The suitable connecting parts for DILO
couplings must be ordered separately.
DILO couplings DN12
3-888-R005 Coupling groove part / BG PN10 DN12 42
3-888-R007 Covering cap 43
3-888-R001 Coupling tongue part PN10 DN12 44
6-1161-R014 Coupling tongue part PN10 DN12
with connecting coupling for measuringdevice
45
3-888-R031 Gauge connecting coupling
PN10 DN12
46
3-888-R009 Gauge connecting coupling
PN10 DN12
47
C 3104-03
-
8/11/2019 DILO Valvesandconnections
42/138
BG PN10 DN12
Coupling groove part
Order No.: 3-888-R005 T
Material:AL
C 3104-03
Suitable connectingparts
3-888-R001
3-888-R007
3-888-R009
Spare O-ringOrder No. 1-05-0057-R087
42
DILO couplings DN12
-
8/11/2019 DILO Valvesandconnections
43/13843
PN10 DN12
Covering cap
Order No.: 3-888-R007 T
Material:AL
C 3104-03
Suitable connectingparts
3-888-R005
Spare O-ringOrder No. 1-05-0057-R096
-
8/11/2019 DILO Valvesandconnections
44/138
PN10 DN12
Coupling tongue part
Order No.: 3-888-R001 T
Material:AL
C 3104-03
Suitable connectingparts
SM...
GS...
ML1-AD22-1ML1-AD22-2
3-240
Suitable connectingparts
3-888-R005
44
DILO couplings DN12
-
8/11/2019 DILO Valvesandconnections
45/138
-
8/11/2019 DILO Valvesandconnections
46/138
PN10 DN12
Gauge connecting coupling
DILO couplings DN12
Order No.: 3-888-R031 T
Material:AL
Suitable connectingparts
3-888-R005
C 3104-03
Spare O-ringOrder No. 1-05-0057-R096
46
-
8/11/2019 DILO Valvesandconnections
47/13847C 3104-03
Order No.: 3-888-R009 T
Material:AL
PN10 DN12
Gauge connecting coupling
Suitable connectingparts
3-888-R005
-
8/11/2019 DILO Valvesandconnections
48/13848
-
8/11/2019 DILO Valvesandconnections
49/13849
DILO couplings DN12
The plug connection allows to esta-
blish a connection by simply fitting
both coupling parts into each other.
Before load relieving of the coupling
seats the pressure- and vacuum tight
coupling is sealed inside with an O-
ring during the coupling process. The
coupling is forced to be open in coup-
led position. If both coupling sides are
separated again the sealing seats shut
off automatically.
All couplings are temperature-resis-
tant from -40 C to +80 C.
The suitable connecting parts for DILO
couplings must be ordered separately.
DILO couplings DN12
3-1095-R005 Plug connection groove part PN8 DN12 50
3-1095-R016 Covering cap fr plug connection
groove part PN8 DN12
51
3-1095-R001 Plug connection tongue part PN8 DN12 52
3-1095-R002 Plug connection tongue part PN8 DN12with connecting coupling for
measuring device
53
3-1095-R017 Density gauge connection PN8 DN12 54
C 3104-03
-
8/11/2019 DILO Valvesandconnections
50/138
PN8 DN12
Plug connection groove part
Order No.: 3-1095-R005 T
Material:AL
C 3104-03
Suitable connectingparts
3-1095-R001
3-1095-R016
Spare O-ringOrder No. 1-05-0057-R087
50
DILO couplings DN12
-
8/11/2019 DILO Valvesandconnections
51/13851
PN8 DN12
Covering cap for plug connection groove part
Order No.: 3-1095-R016 T
Material:AL
C 3104-03
Suitable connectingparts
3-1095-R005
-
8/11/2019 DILO Valvesandconnections
52/138
PN8 DN12
Plug connection tongue part
Order No.: 3-1095-R001 T
Material:AL
C 3104-03
Suitable connectingparts
3-1095-R005
Suitable connectingparts
SM...
GS...
ML1-AD22-1ML1-AD22-2
52
DILO couplings DN12
-
8/11/2019 DILO Valvesandconnections
53/13853
PN8 DN12
Plug connection tongue partwith connecting coupling for measuring device
Order No.: 3-1095-R002 T
Material:AL
C 3104-03
Suitable connectingparts
3-1095-R005
Suitable connectingparts
hose formeasuring device
-
8/11/2019 DILO Valvesandconnections
54/138
PN8 DN12
Density gauge connection
DILO couplings DN12
Order No.: 3-1095-R017 T
Material:AL
Suitable connectingparts
3-1095-R005
Indication range on customerrequest
C 3104-0354
-
8/11/2019 DILO Valvesandconnections
55/13855
DILO couplings DN20
DILO couplings DN20
VK/A-02/20 Coupling groove part / A PN64 DN20 56
VK/B(G)-03/20 Coupling groove part PN64 DN20
with O-ring
57
VK/FL-01/20 Flange coupling PN64 DN20 58
3-777-R001 Flange coupling PN64 DN20with 2-hole ange
59
3-685-R001 Flange coupling PN64 DN20 60
VK/KN-04/20 Covering cap for coupling groove
part PN64 DN20
61
VK/F-02/20 Coupling tongue part PN64 DN20 62
3-1121-R003 DN20 Quick coupling 63
6-1161-R012 Coupling tongue part PN64 DN20
with connecting coupling for
measuring device
64
6-1281-R001 Coupling tongue part with airlter
65
SK-282-R020 Gauge connecting coupling
PN64 DN20
66
C 3105-04
The coupling allows to establish a
connection by simply fitting both
coupling parts into each other. Before
load relieving of the coupling seats
the pressure- and vacuum tight cou-
pling is sealed inside with an O-ring
during the coupling process. The cou-
pling is forced to be open in coupled
position. If both coupling sides are
separated again the sealing seats shut
off automatically.
All couplings are temperature-resis-
tant from -40 C to +80 C.
In special version these couplings are
also available for a temperature range
of -60 C to +80 C.
The suitable connecting parts for DILO
couplings must be ordered separately.
-
8/11/2019 DILO Valvesandconnections
56/138
A PN64 DN20
Coupling groove part
C 3105-04
Suitable connectingparts
SM...
GS...
ML1-AD22-1ML1-AD22-2
3-240
Suitable connectingparts
SK-282-R001
VK/F-02/20
VK/KN-04/20
Order No. Material
VK/A-02/20 T AL
VK/A-02/20 P Brass
VK/A-02/20 E Stainless steel
56
DILO couplings DN20
-
8/11/2019 DILO Valvesandconnections
57/13857
PN64 DN20
Coupling groove part with O-ring
C 3105-04
Suitable connectingparts
SK-282-R001
VK/F-02/20
VK/KN-04/20
In special version the screw-in thread can also be suppliedwith sealing edge acc. to DIN 3852 form B.
Spare O-ringOrder No. 1-05-0057-R039
d4 Order No. Material
M33 x 2 VK/B-03/20 T AL
M33 x 2 VK/B-03/20 P Brass
M33 x 2 VK/B-03/20 E Stainless steel
G 1 A VK/BG-03/20 T AL
G 1 A VK/BG-03/20 P Brass
G 1 A VK/BG-03/20 E Stainless steel
-
8/11/2019 DILO Valvesandconnections
58/138
PN64 DN20
Flange coupling
C 3105-04
Suitable connectingparts
SK-282-R001
VK/F-02/20
VK/KN-04/20
Other anges are available on request.
Spare O-ringOrder No. 1-05-0057-R030
Order No. Material
VK/FL-01/20 T AL
VK/FL-01/20 E Stainless steel
58
DILO couplings DN20
-
8/11/2019 DILO Valvesandconnections
59/13859
PN64 DN20
Flange coupling with 2-hole ange
Order No.: 3-777-R001 T
Material:AL
C 3105-04
Suitable connectingparts
SK-282-R001
VK/F-02/20
VK/KN-04/20
Other anges are available on request.
Spare O-ringOrder No. 1-05-0057-R098
-
8/11/2019 DILO Valvesandconnections
60/138
PN64 DN20
Flange coupling
Order No.: 3-685-R001 T
Material:AL
C 3105-04
Suitable connectingparts
SK-282-R001
VK/F-02/20
VK/KN-04/20
Other anges are available on request.
Spare O-ringOrder No. 1-05-0057-R116
60
DILO couplings DN20
-
8/11/2019 DILO Valvesandconnections
61/13861
PN64 DN20
Covering cap for coupling groove part
C 3105-04
Suitable connectingparts
3-777-R001
VK/FL-01/20
3-685-R001
VK/A-02/20
VK/B-03/20VK/BG-03/20
Spare O-ringOrder No. 1-05-0057-R116
Order No. Material
VK/KN-04/20 T AL
VK/KN-04/20 E Stainless steel
-
8/11/2019 DILO Valvesandconnections
62/138
PN64 DN20
Coupling tongue part
C 3105-04
Suitable connectingparts
3-777-R001
VK/FL-01/20
3-685-R001
VK/A-02/20
VK/B-03/20VK/BG-03/20
Suitable connectingparts
SM...
GS...
ML1-AD22-1ML1-AD22-2
3-240
Spare O-ringOrder No. 1-05-0057-R010
Order No. Material
VK/F-02/20 T AL
VK/F-02/20 E Stainless steel
VK/F-02/20 P Brass
62
DILO couplings DN20
-
8/11/2019 DILO Valvesandconnections
63/13863
3-1121-R003
DN20 Quick coupling
C 3105-04
For easy coupling and uncoupling of hoses
The quick coupling is very useful in all elds of application where hoses have to be frequently loo -sened and reconnected e. g. during nal tests of completely mounted GIS elds. Thanks to the clamplock the DN20 hoses can easily be connected without any loss of SF
6gas. Thus the handling times in
GIS production are shortened and productivity is increased considerably.
Important note:
The quick coupling is only compatible with DILO coupling groove parts of version 2
(additional V2 stamp on the flange or wrench size).
closed coupling
open coupling
Suitable connectingparts
SM...
GS...
Suitable connectingparts
3-777-R...
VK/FL-01/20
3-685-R...
VK/A-02/20
VK/B-03/20VK/BG-03/20
SK-507-R..
-
8/11/2019 DILO Valvesandconnections
64/138
PN64 DN20
Coupling tongue partwith connecting coupling for measuring device
Order No.: 6-1161-R012
Material:Brass
C 3105-04
Suitable connectingparts
3-777-R001
VK/FL-01/20
3-685-R001
VK/A-02/20
VK/B-03/20VK/BG-03/20
Suitable connectingparts
hose formeasuring device
64
DILO couplings DN20
-
8/11/2019 DILO Valvesandconnections
65/13865
PN64 DN20
Coupling tongue part with air lter
C 3105-04
Order No.: 6-1281-R001
Material:Brass
Suitable connectingparts
3-777-R001
VK/FL-01/20
3-685-R001
VK/A-02/20
VK/B-03/20VK/BG-03/20
Description
This coupling tongue part allows gas compartments which are under
vacuum to be ooded with air after the SF6gas recovery and it is not
necessary to use any service cart.
The integrated 100-m lter sieve prevents dirt particles from ambientair penetrating the gas compartment during the ooding process.
-
8/11/2019 DILO Valvesandconnections
66/138C 3105-04
PN64 DN20
Gauge connecting coupling
Suitable connectingparts
3-777-R001
VK/FL-01/20
3-685-R001
VK/A-02/20
VK/B-03/20VK/BG-03/20
Suitable connectingparts
Gauge withconnecting thread
G A
Description
The gauge connecting coupling serves as connecting piece to a coupling
groove part DN20. When coupling, a pin in the gauge connecting coupling
opens the ow of the opposite coupling groove part (forced opening). Thisallows to read the present operating pressure on the screwed-in gauge.
When disconnecting, the concial nipple of the groove part is closed by
spring load (pressure and vacuum tight). If the gauge connecting coupling
is not connected the gauge shows zero pressure. The connecting coup-
ling allows to install the gauge in any required position (rotatable 360).
Spare O-ring
Order No. 1-05-0057-R225
Spare O-ringOrder No. 1-05-0057-R010
Order No. Material
SK-282-R020 T AL
SK-282-R020 P Brass
66
DILO couplings DN20
-
8/11/2019 DILO Valvesandconnections
67/13867
DILO couplings DN40
The coupling allows to establish a
connection by simply fitting both
coupling parts into each other. Before
load relieving of the coupling seats
the pressure- and vacuum tight cou-
pling is sealed inside with an O-ring
during the coupling process. The cou-
pling is forced to be open in coupled
position. If both coupling sides are
separated again the sealing seats shut
off automatically.
All couplings are temperature-resis-
tant from -40 C to +80 C.
The suitable connecting parts for DILO
couplings must be ordered separately.
DILO couplings DN40
VK/A-02/40 Coupling groove part / A PN16 DN40 68
VK/FL-01/40 Flange coupling PN16 DN40 69
VK/KN-01/40 Covering cap PN16 DN40 70
VK/F-01/40 Coupling tongue part PN16 DN40 71
C 3106-03
-
8/11/2019 DILO Valvesandconnections
68/138
A PN16 DN40
Coupling groove part
Order No.: VK/A-02/40 E
Material:Stainless steel
C 3106-03
Suitable connectingparts
VK/F-01/40
VK/KN-01/40
68
DILO couplings DN40
-
8/11/2019 DILO Valvesandconnections
69/13869
PN16 DN40
Flange coupling
Order No.: VK/FL-01/40 E
Material:Stainless steel
C 3106-03
Suitable connectingparts
VK/F-01/40
VK/KN-01/40
Other anges are available on request.
Spare O-ringOrder No. 1-05-0057-R126
-
8/11/2019 DILO Valvesandconnections
70/138
PN16 DN40
Covering cap
Order No.: VK/KN-01/40 T
Material:AL
C 3106-03
Suitable connectingparts
VK/FL-01/40
Spare O-ringOrder No. 1-05-0057-R126
70
DILO couplings DN40
-
8/11/2019 DILO Valvesandconnections
71/13871
PN16 DN40
Coupling tongue part
Order No.: VK/F-01/40 E
Material:Stainless steel
C 3106-03
Suitable connectingparts
VK/FL-01/40
VK/A-02/40
Suitable connectingparts
SM0140
ML1-AD42-1ML1-AD42-2
Spare O-ringOrder No. 1-05-0057-R141
-
8/11/2019 DILO Valvesandconnections
72/13872
-
8/11/2019 DILO Valvesandconnections
73/13873
DILO soldering unions
DILO soldering unions are particularly
used in factory fabrication area piping.
DILO offers a very wide variety of
unions. Soldering unions are available
either with soldering connections on
both ends where the highest vibra-
tion resistance is required or with a
soldering connection on one end and
a screw in thread the other.
DILO soldering unions withstand pres-
sures up to 64 bar.
Different materials are available for all
applications.
The suitable connecting parts for DILO
couplings must be ordered separately.
DILO soldering unions of the ML1 series for pressures
up to PN64
ML1A-AD Soldering stub-soldering union PN64 74
ML1BO-AD Screw-in stub-soldering union PN64
with O-ring
75
ML1M-AD10 Gauge union PN64 DN8 76
3-328-R020 Gauge union PN64 DN8 77
ML1-..8 Blanking disk PN64 78
VST03 Plug PN64 78
1-05-1545-R... Tee piece 79
1-05-1545-R... Angle piece 79
1-05-1545-R... Plug-in angle piece 80
C 3107-04
-
8/11/2019 DILO Valvesandconnections
74/138
PN64
Soldering stub-soldering union
C 3107-04
Piece Designation Order No. Material
1 Soldering shoulder-tongue part ML1-AD________-1 P = Brass / C = Stainless steel
2 Clamping nut ML1-AD________-2 P = Brass / C = Stainless steel
3 Soldering stub-groove part ML1-AD________-3 P = Brass / C = Stainless steel
Note: For the nominal width (outside diameter 10) the clamping nut is made of stainless steel.
Tube outsidediameter AD
d2 d3 L1 I1 h1 h3 h6 h7 m1 m2 i1 s1 s3 Order No.
10 8 M20x1,5 35 20 9,5 4 8 8 18 4 12 22 24 ML1A-AD10 P
10 8 M20x1,5 35 20 9,5 4 8 8 18 4 12 22 24 ML1A-AD10 C
15 12 M26x1,5 52 22 13,5 5 10 10 20 5 12 27 32 ML1A-AD15 P
22 19 M36x2 54 31 15,5 6 12 12 26 7 16 41 41 ML1A-AD22 P
22 19 M36x2 54 31 15,5 6 12 12 26 7 16 41 41 ML1A-AD22 C
42 35 M56x2 65 37 19,5 7 20 20 29 7 18 60 65 ML1A-AD42 P
42 35 M56x2 65 37 19,5 7 20 20 29 7 18 60 65 ML1A-AD42 C
74
DILO soldering unions
-
8/11/2019 DILO Valvesandconnections
75/13875
PN64
Screw-in stub-soldering union with O-ring
C 3107-04
Note: For the nominal width (outside diameter 10) the clamping nut is made of stainless steel.Regarding material AL only part 13 or 14 is made of AL, part 1 and 2 are made of stainless steel.
In special version the screw-in thread can also be supplied with sealing edge according to DIN 3852
form B.
Piece Designation Order No. Material
1 Soldering shoulder-tongue part ML1-AD________-1 P = Brass / C = Stainless steel
2 Clamping nut ML1-AD________-2 P = Brass / C = Stainless steel
13 Screw-in stub(M16x1,5 / M33x2)
ML1-AD________-13 P = Brass / T = AL
14 Screw-in stub(G 3/8 A / G A / G 1 A /G 1 A)
ML1-AD________-14 P = Brass / T = AL
Tube outsidediameter
AD
d2 d3 d4 d7 L2 I2 h1 h3 h7 m1 m2 i1 i2 a2 s2 s3 Order No.
10 8 M20x1,5 M16x1,5 26 40 25 9,5 4 8 18 4 12 12 2 27 24 ML1BO-AD10 P
10 8 M20x1,5 M16x1,5 26 40 25 9,5 4 8 18 4 12 12 2 27 24 ML1BO-AD10 T
10 8 M20x1,5 G 3/8 A 26 40 25 9,5 4 8 18 4 12 12 2 27 24 ML1BO-AD10G P
10 8 M20x1,5 G 3/8 A 26 40 25 9,5 4 8 18 4 12 12 2 27 24 ML1BO-AD10G T
15 12 M26x1,5 G A 32 47 27 13,5 5 10 20 5 12 14 3 32 32 ML1BO-AD15G P
22 19 M36x2 M33x2 49 59 36 15,5 6 12 26 7 16 18 3 50 41 ML1BO-AD22 P
22 19 M36x2 M33x2 49 59 36 15,5 6 12 26 7 16 18 3 50 41 ML1BO-AD22 T
22 19 M36x2 G 1 A 49 59 36 15,5 6 12 26 7 16 18 3 50 41 ML1BO-AD22G P
22 19 M36x2 G 1 A 49 59 36 15,5 6 12 26 7 16 18 3 50 41 ML1BO-AD22G T
42 35 M56x2 G 1 A 65 69 41 19,5 7 20 29 7 18 22 3 65 65 ML1BO-AD42G P
Spare O-ringOrder No. AD10: 1-05-0057-R016 AD15: 1-05-0057-R087 AD22: 1-05-0057-R039 AD42: 1-05-0057-R126
-
8/11/2019 DILO Valvesandconnections
76/138
PN64 DN8
Gauge union
C 3107-04
Piece Designation Order No. Material
1 Soldering shoulder-tongue part ML1-AD10-1 P Brass
2 Clamping nut ML1-AD10-2 C Stainless steel
3 Gauge connecting piece M1-10-51 P Brass
3 Gauge connecting piece M1-10-59 P Brass
Tube outsidediameter
AD
d2 d3 d4 d19 L10 I10 h1 h3 h7 m1 m2 i1 i5 s3 s8 Order No.
10 8 M20x1,5 G 1/2 7,5 49 34 9,5 4 8 18 4 12 16 24 24 ML1M-AD10/51
10 8 M20x1,5 G 1/4 5,5 44 29 9,5 4 8 18 4 12 13 24 22 ML1M-AD10/59
76
DILO soldering unions
-
8/11/2019 DILO Valvesandconnections
77/13877
PN64 DN8
Gauge union
C 3107-04
Order No.: 3-328-R020 P
Material:Brass
Suitable connectingparts
Gauge withconnecting thread
G A
Suitable connectingparts
ML1-AD10-1ML1-AD10-2
Spare O-ringOrder No. 1-05-0057-R225
-
8/11/2019 DILO Valvesandconnections
78/138
PN64
Blanking disk
DILO soldering unions
PN64
Plug
Tube outside diameter AD h3 Order No. Material
10 1,5 ML1-10-8 P Brass
22 2 ML1-22-8 P Brass
42 3 ML1-42-8 P Brass
Metric ne thread ISO Whitworth pipe thread Spare O-ring
d4 d7 n1 i1 a2 s2 Order No. Material d4 Order No. Material Order No.
23 23 12 2 24 G 1/4 A VST03 / G 1/4 A T AL 1-05-0057-R088
M16x1,5 26 24 12 2 27 VST03 / M16x1,5 AL G 3/8 A VST03 / G 3/8 A T AL 1-05-0057-R016
36 32 15 3 36 G 1/2 A VST03 / G 1/2 A T AL 1-05-0057-R033
M33x2 49 38 18 3 50 VST03 / M33x2 T AL G 1 A VST03 / G 1 A T AL 1-05-0057-R039
65 45 22 3 65 G 1 A VST03 / G 1 A T AL 1-05-0057-R126
C 3107-0478
-
8/11/2019 DILO Valvesandconnections
79/138
-
8/11/2019 DILO Valvesandconnections
80/138C 3107-04
Plug-in angle piece
dd dd11 11
AAAADDDD
dddd2222
llll1111
LL LL11 11
hhhh7777
LLLL2222
DILO soldering unions
Tube outsidediameter AD
PN d2 L1 h7 L2 d1 I1 Order No. Material
10 64 8 14,5 8 21,5 10 10 1-05-1545-R010 Brass
15 64 12 19 10 26 15 13 1-05-1545-R011 Brass
22 64 19 24,5 12 34 22 16 1-05-1545-R012 Brass
42 25 39 45 20 56,4 42 24 1-05-1545-R013 Brass
80
-
8/11/2019 DILO Valvesandconnections
81/13881
DILO ball valves
The ball valve has a compact design
and is maintenance-free. The notch on
the spindle head and the position of
the handle show the flow rate (closed
or opened). The flow rate is controlled
by a ball which is stored in a sealing.
Each ball valve is tested for tightness
in our works.
All ball valves are temperature-resis-
tant from -40 C to +80 C.
The suitable connecting parts must be
ordered separately.
DILO ball valves for pressures up to PN64
3-365-R001 Ball valve PN64 DN8 82
3-365-R008 Ball valve with handwheel PN64 DN8 83
3-383-R001 Ball valve PN64 DN20 84
3-679-R001 Ball valve PN25 DN40 85
C 3108-02
-
8/11/2019 DILO Valvesandconnections
82/138
PN64 DN8
Ball valve
Order No.: 3-365-R001 P
Material:Brass
C 3108-02
Suitable connectingparts on both ends
SM...
ML1-AD10-1ML1-AD10-2
GS...
other connections are available
82
DILO ball valves
-
8/11/2019 DILO Valvesandconnections
83/13883
PN64 DN8
Ball valve with handwheel
Order No.: 3-365-R008 P
Material:Brass
C 3108-02
Suitable connectingparts on both ends
SM...
ML1-AD10-1ML1-AD10-2
GS...
-
8/11/2019 DILO Valvesandconnections
84/138
PN64 DN20
Ball valve
Order No.: 3-383-R001 P
Material:Brass
C 3108-02
Suitable connectingparts on both ends
SM...
ML1-AD22-1ML1-AD22-2
GS... other connections are available
84
DILO ball valves
-
8/11/2019 DILO Valvesandconnections
85/13885
PN25 DN40
Ball valve
Order No.: 3-679-R001 P
Material:Brass
C 3108-02
Suitable connectingparts on both ends
SM...
ML1-AD42-1ML1-AD42-2
GS...
-
8/11/2019 DILO Valvesandconnections
86/13886
-
8/11/2019 DILO Valvesandconnections
87/13887
DILO hoses
C 3109-05
We also offer wire braided stainless
steel hoses as well as rubber hoses.
Both hose types can be used up to
64 bar. They are pressure and vacuum
tight and are available with different
coupling connections. No matter
whether you need a hose for
connection to SF6maintenance
devices, gas insulated fabrication
plants or other devices, we can offer
the appropriate hose connection.
The suitable connecting parts must be
ordered separately.
DILO hoses for pressures up to PN64
SM01 Wire braided hose DN8 / DN20 / DN40 88
SM03 Wire braided hose with elbow connection
DN8 / DN20 / DN40
89
SM07 Wire braided hose with elbow connections
DN8 / DN20
90
SM10 Wire braided hose with protective hose
DN8 / DN20 / DN40
91
GS01 Rubber hose DN8 / DN20 / DN40 92
GS03 Rubber hose with elbow connection
DN8 / DN20
93
Ordering examples
-
8/11/2019 DILO Valvesandconnections
88/138
DN8 / DN20 / DN40
Wire braided hose
C 3109-05
Suitable connectingparts
ML1-AD10-3ML1-AD22-3ML1-AD42-3
VK/F-02/8VK/F-02/20VK/F-01/40
3-308-R002
3-888-R001
VK/A-02/20VK/A-01/40
admissiblestatic operating
pressure at20C SF 3
nominalpressure level
DIN EN ISO10380 SF 4
AD DN d2 d3 s3 minimumbending
radius /onetimebending
nominalbending
radius /frequent
movements
Order No.* NL in mm
64 64 10 8 8 M20x1,5 24 38 130 SM018L ___________
55 40 22 20 19 M36x2 41 70 170 SM0120L ___________
60 40 42 40 35 M56x2 65 130 300 SM0140L ___________
Structure of the rust- and acid resistant wire braided hose:
Full metal wall made of 1.4404 with outside wire sheating made
of stainless steel, both ends completely equipped with DILO-
connections made of brass.(For nominal diameter AD10 the clamping nut is made of stain-
less steel).
Supply length: max. 25 m
*Ordering example see page 94
88
DILO hoses
-
8/11/2019 DILO Valvesandconnections
89/13889
DN8 / DN20 / DN40
Wire braided hose with elbow connection
C 3109-05
Suitable connectingparts
ML1-AD10-3ML1-AD22-3ML1-AD42-3
VK/F-02/8VK/F-02/20VK/F-01/40
3-308-R002
3-888-R001
VK/A-02/20VK/A-01/40
Structure of the rust- and acid resistant wire braided hose:
Full metal wall made of 1.4404 with outside wire sheating made
of stainless steel, both ends completely equipped with DILO-
connections made of brass.(For nominal diameter AD10 the clamping nut is made of stain-
less steel).
Supply length: max. 25 m
admissiblestatic operating
pressure at20C SF 3
nominalpressure level
DIN EN ISO10380 SF 4
AD DN d2 d3 s3 minimumbending
radius /onetimebending
nominalbending
radius /frequent
movements
Order No.* NL in mm
64 64 10 8 8 M20x1,5 24 38 130 SM038L ___________
55 40 22 20 19 M36x2 41 70 170 SM0320L ___________
60 40 42 40 35 M56x2 65 130 300 SM0340L ___________
*Ordering examples see page 94
-
8/11/2019 DILO Valvesandconnections
90/138
DN8 / DN20
Wire braided hose with elbow connections
C 3109-05
Suitable connectingparts
ML1-AD10-3ML1-AD22-3
VK/F-02/8VK/F-02/20
3-308-R002
3-888-R001
VK/A-02/20
Structure of the rust- and acid resistant wire braided hose:
Full metal wall made of 1.4404 with outside wire sheating made
of stainless steel, both ends completely equipped with DILO-
connections made of brass.(For nominal diameter AD10 the clamping nut is made of stain-
less steel).
Supply length: max. 25 m
admissible
static opera-ting pressureat 20C SF 3
nominal
pressure levelDIN EN ISO10380 SF 4
AD DN d2 d3 s3 minimum
bending radi-us / onetimebending
nominal ben-
ding radius/ frequentmovements
Order No.* NL in mm
64 64 10 8 8 M20x1,5 24 38 130 SM078L ________
55 40 22 20 19 M36x2 41 70 170 SM0720L ________
*Ordering example see page 94
90
DILO hoses
-
8/11/2019 DILO Valvesandconnections
91/138
-
8/11/2019 DILO Valvesandconnections
92/138
DN8 / DN20 / DN40
Rubber hose
C 3109-05
Suitable connectingparts
ML1-AD10-3ML1-AD22-3ML1-AD42-3
VK/F-02/8VK/F-02/20VK/F-01/40
3-308-R002
3-888-R001
VK/A-02/20VK/A-01/40
Pressurestage bar
FittingAD
HoseDN
Hosed
Fittingd2
Fittingd3
Fittings3
Bendingradius
Order No.* NL in mm
64 10 8 7,9 5,5 M20x1,5 24 50 GS0108L ___________
50 22 20 19 15,5 M36x2 41 240 GS0120L ___________
64 42 40 38 33 M56x2 65 500 GS0140L ___________
Range of application and temperature:
From -40 C up to +100 C according to the medium used
(see DIN EN 853/854)
Materials and composition:
The hoses consist of an internal layer made of synthetic rubber
which is oil- and waterproof and of external rubber layer whick
is oil- and weatherproof.
Fitting material:Brass(For nominal diameter AD10 the clamping nut is made of
stainless steel)
The hose tting is made in pressnipple form.
*Ordering example see page 94
92
DILO hoses
-
8/11/2019 DILO Valvesandconnections
93/138
-
8/11/2019 DILO Valvesandconnections
94/138
-
8/11/2019 DILO Valvesandconnections
95/13895
DILO transition pieces and adapters
C 3110-03
Our product range comprises a large
variety of transition pieces and adap-
ters to establish connections between
components with different nominal
lengths. Thus DILO connecting coup-
lings and hoses allow the comfortable
adaption to other coupling systems
on switchgear.
The suitable connecting parts must be
ordered separately.
DILO transition pieces and adapters for pressures up to PN64
6-1033-R001/6-1058-R.../SK-279-R... / 6-1027-R...
Adapter DILO couplings DN20ASEA / Magrini / Siemens/Westinghouse
96 - 99
3-920-R002/R001 Adapter - Hansen connection 100 - 101
3-353-R005/R006 Adapter DILO DN8 -
Michelin valve
102 - 103
6-1059-R.../6-1203-R... Adapter with ange coupling onboth ends
104
K022R02 Tee piece with DILO couplings 105
3-351-R001 P Screw-in stub 106
SK-386 T/3-240-R.../3-251-R001/3-314-R001
Transition pieces 107 - 110
3-227-R001/3-311-R001/3-984-R001
Intermediate pieces 111
3-816-R001/R005 Transition pieces 112 - 113
K018R02/R06/
3-717-R.../K018R07/K018R..
Angle pieces 114 - 118
K020R.. Tee pieces 119 - 120
3-718-R006 Distributor 121
3-1026-R002 Tubings 122
-
8/11/2019 DILO Valvesandconnections
96/138C 3110-03
Order No.: 6-1033-R001
Material:Brass
Suitable connectingparts
SK-282-R001
VK/F-02/20
VK/KN-04/20
Suitable connectingparts
ASEA connection
PN64 DN20
Adapter DN20 DILO coupling -ASEA connection
96
DILO transition pieces and adapters
-
8/11/2019 DILO Valvesandconnections
97/13897C 3110-03
Suitable connectingparts
Magrini connection
Suitable connectingparts
SK-282-R001
VK/F-02/20
VK/KN-04/20
d3 Order No. Material
14 6-1058-R001 Brass
16 6-1058-R002 Brass
PN64 DN20
Adapter DN20 DILO coupling -Magrini connection
-
8/11/2019 DILO Valvesandconnections
98/138C 3110-03
Suitable connectingparts
SK-282-R001
VK/F-02/20
VK/KN-04/20
Suitable connectingparts
Siemens connection
d3 L S3 Order No. Material
G 3/4 97 32 SK-279-R001 P Brass
G 1 98 41 SK-279-R002 P Brass
G 1 1/4 93 50 SK-279-R003 P Brass
PN64 DN20
Adapter DN20 DILO coupling -Siemens connection
98
DILO transition pieces and adapters
-
8/11/2019 DILO Valvesandconnections
99/13899C 3110-03
Suitable connectingparts
Westinghouseconnection
Suitable connectingparts
SK-282-R020
VK/F-02/20
VK/KN-04/20
d3 L S3 Order No. Material
1 5/8 - 12UN 97 50 6-1027-R001 Brass
1 5/16 - 12UN 95 41 6-1027-R002 Brass
1 1/16 - 12UN 90 32 6-1027-R003 Brass
PN64 DN20
Adapter DN20 DILO coupling -Westinghouse connection
-
8/11/2019 DILO Valvesandconnections
100/138C 3110-03
Order No.: 3-920-R002 P
Material:Brass
Suitable connectingparts
Hansen connectionG 3/4 A
Suitable connectingparts
SK-282-R020
VK/F-02/20
VK/KN-04/20
PN64 DN20
Adapter DN20 DILO coupling -Hansen connection
100
DILO transition pieces and adapters
-
8/11/2019 DILO Valvesandconnections
101/138101C 3110-03
Order No.: 3-920-R001 P
Material:Brass
Suitable connectingparts
SK-372-R...
VK/F-02/8
VK/KN-04/8
Suitable connectingparts
Hansen connectionG 1/4 A
PN64 DN8
Adapter DN8 DILO coupling -Hansen connection
-
8/11/2019 DILO Valvesandconnections
102/138
PN2 DN8
DILO DN8 adapter Michelin valve
C 3110-03
Order No.: 3-353-R005 P
Material:Brass
Suitable connectingparts
SM...
ML1-AD10-1ML1-AD10-2
GS...
102
DILO transition pieces and adapters
-
8/11/2019 DILO Valvesandconnections
103/138103C 3110-03
PN2 DN8
DILO DN8 adapter Michelin valve
Order No.: 3-353-R006 P
Material:Brass
Suitable connectingparts
ML1-AD10-3
VK/F-02/8
VK/A-02/8
3-308-R002
-
8/11/2019 DILO Valvesandconnections
104/138C 3110-03
Adapter with ange coupling on both ends
Suitable connectingparts on both ends
3-408-R001
VK/F-02/8VK/F-02/20VK/F-01/40
DN for couplingtongue part
d3 L H PN Order No. Material
6 3-408-R001 M24x1,5 92 40 10 6-1059-R004 AL
8 VK/F-02/8 M26x1,5 74 40 64 6-1059-R012 AL
20 VK/F-02/20 M45x2 92 80 64 6-1059-R011 AL
40 VK/F-01/40 M76x2 102 110 16 6-1203-R001 Stainless steel
104
DILO transition pieces and adapters
-
8/11/2019 DILO Valvesandconnections
105/138105C 3110-03
PN64 DN8 / DN20
Tee piece with DILO couplings
Order No.: K022R02
Material:AL
Suitable connectingparts
3-777-R001
VK/FL-01/20
3-685-R001
VK/A-02/20
VK/B-03/20VK/BG-03/20
Suitable connectingparts
SK-282-R001
VK/F-02/20
VK/KN-04/20
Other versions are available.
Suitable connectingparts
SK-372-R... VK/F-02/8 VK/KN-04/8
-
8/11/2019 DILO Valvesandconnections
106/138
PN64 DN8
Screw-in stub
C 3110-03
Order No.: 3-351-R001 P
Material:Brass
Suitable connectingparts
SM018SM038
ML1-AD10-1
ML1-AD10-2
GS0108GS0308
Suitable connectingparts
G internal thread
106
DILO transition pieces and adapters
-
8/11/2019 DILO Valvesandconnections
107/138107
PN64 DN8
Transition piece DN8
C 3110-03
Order No.: SK-386 T
Material:AL
Suitable connectingparts
SM018SM038
ML1-AD10-1
ML1-AD10-2
GS0108GS0308
Suitable connectingparts
G 3/8 external thread
-
8/11/2019 DILO Valvesandconnections
108/138
PN64 DN8 / DN20
Transition piece
C 3110-03
Suitable connectingparts
SM018SM038
ML1-AD10-1
ML1-AD10-2
GS0108GS0308
Suitable connectingparts
ML1-AD22-3
VK/F-02/20
VK/A-02/20
Order No. Material
3-240-R001 P Brass
3-240-R001 C Stainless steel
108
DILO transition pieces and adapters
-
8/11/2019 DILO Valvesandconnections
109/138109
PN64 DN20 / DN8
Transition piece
C 3110-03
Order No.: 3-251-R001 P
Material:Brass
Suitable connectingparts
SM0120SM0320
ML1-AD22-1
ML1-AD22-2
GS0120GS0320
Suitable connectingparts
ML1-AD10-3
VK/F-02/8
VK/A-02/8
3-308-R002
-
8/11/2019 DILO Valvesandconnections
110/138
PN64 DN20 / DN8
Transition piece
C 3110-03
Order No.: 3-314-R001 P
Material:Brass
Suitable connectingparts
ML1-AD10-3
VK/F-02/8
VK/A-02/8
3-308-R002
Suitable connectingparts
ML1-AD22-3
VK/F-02/20
VK/A-02/20
110
DILO transition pieces and adapters
-
8/11/2019 DILO Valvesandconnections
111/138111
PN64 DN8 / DN20 / DN40
Intermediate piece
C 3110-03
AD d3 L m1 s1 Order No. Material
10 M20x1,5 32 18 24 3-227-R001 P Brass
22 M36x2 48 26 41 3-311-R001 P Brass
42 M56x2 58 29 65 3-984-R001 P Brass
Suitable connectingparts
ML1-AD10-3ML1-AD22-3ML1-AD42-3
VK/F-02/8VK/F-02/20VK/F-01/40
VK/A-02/8VK/A-02/20VK/A-01/40
3-308-R002(only for 3-227-R001 P)
3-888-R001(only for 3-311-R001 P)
-
8/11/2019 DILO Valvesandconnections
112/138
PN64 DN40 / DN20
Transition piece
C 3110-03
Order No.: 3-816-R001 P
Material:Brass
Suitable connectingparts
SM0140
ML1-AD42-1ML1-AD42-2
GS0140
Suitable connectingparts
ML1-AD22-3
VK/F-02/20
VK/A-02/20
112
DILO transition pieces and adapters
-
8/11/2019 DILO Valvesandconnections
113/138113
PN64 DN40 / DN20
Transition piece
C 3110-03
Order No.: 3-816-R005 P
Material:Brass
Suitable connectingparts
SM0140
ML1-AD42-1ML1-AD42-2
GS0140
Suitable connectingparts
SM0120
ML1-AD22-1ML1-AD22-2
GS0120
-
8/11/2019 DILO Valvesandconnections
114/138
PN64 DN8 / DN20 / DN40
Angle piece
C 3110-03
Suitable connectingparts
SM...
ML1-AD..-1ML1-AD..-2
GS...
Suitable connectingparts
ML1-AD22-3ML1-AD42-3
VK/F-02/20
VK/F-01/40
VK/A-02/20VK/A-02/40
3-888-R001
AD d3 d4 L H s1 s2 Order No. Material
10/22 M36x2 M20x1,5 45 51 41 22 K018R02 Brass
22/42 M56x2 M36x2 64 81 65 41 K018R06 Brass
114
DILO transition pieces and adapters
-
8/11/2019 DILO Valvesandconnections
115/138115
PN64 DN8 /DN20 / DN40
Angle piece
C 3110-03
Suitable connectingparts
SM...
ML1-AD..-1ML1-AD..-2
GS...
Suitable connectingparts
ML1-AD10-3ML1-AD22-3ML1-AD42-3
VK/F-02/8
VK/F-02/20VK/F-01/40
VK/A-02/8VK/A-02/20VK/A-02/40
3-888-R001(only for 3-717-R002 P)
AD d3 L H s1 s2 Order No. Material
10 M20x1,5 32 31 22 24 3-717-R001 P Brass
22 M36x2 48 46 36 41 3-717-R002 P Brass
42 M56x2 58 65 60 65 K018R07 Brass
-
8/11/2019 DILO Valvesandconnections
116/138
-
8/11/2019 DILO Valvesandconnections
117/138117
PN64 DN8 / DN20 / DN40
Angle piece
C 3110-03
Suitable connectingparts
ML1-AD10-3ML1-AD22-3ML1-AD42-3
VK/F-02/8VK/F-02/20VK/F-01/40
VK/A-02/8VK/A-02/20VK/A-02/40
3-888-R001
AD d3 d4 L H s1 s2 Order No. Material
10/22 M36x2 M20x1,5 45 46 41 24 K018R27 Brass
22/42 M56x2 M36x2 64 72 65 41 K018R31 Brass
-
8/11/2019 DILO Valvesandconnections
118/138
PN64 DN8 / DN20
Angle piece
C 3110-03
Suitable connectingparts
SM...
ML1-AD..-1ML1-AD..-2
GS...
AD d3 L H s1 Order No. Material
10 M20x1,5 38 34 22 K018R41 Brass
22 M36x2 59 53 41 K018R40 Brass
42 M56x2 85 73 60 K018R29 Brass
118
DILO transition pieces and adapters
-
8/11/2019 DILO Valvesandconnections
119/138119
PN64 DN8 / DN20
Tee piece
C 3110-03
AD d3 L H s1 Order No. Material
10 M20x1,5 56 64 24 K020R66 Brass
22 M36x2 93 98 41 K020R14 Brass
Suitable connectingparts
ML1-AD10-3ML1-AD22-3
VK/F-02/8VK/F-02/20
VK/A-02/8VK/A-02/20
3-308-R002(only for K020R66)
3-888-R001(only for K020R14)
-
8/11/2019 DILO Valvesandconnections
120/138C 3110-03
PN64 DN8 / DN20
Tee piece
Suitable connectingparts
SM...
ML1-AD..-1ML1-AD..-2
GS...
AD d3 L H s1 Order No. Material
10 M20x1,5 56 75 22 K020R26 Brass
22 M36x2 104 112 41 K020R59 Brass
120
DILO transition pieces and adapters
-
8/11/2019 DILO Valvesandconnections
121/138121C 3110-03
3 x DN20 / 1 x DN40
Distributor
Order No.: 3-718-R006
Suitable connectingparts
VK/F-02/20 PCoupling groove part
DN20
Other versions are available.
3-383-R001 PBall valve DN20
Suitable connectingparts
VK/F-01/40 ECoupling tongue part
DN40
-
8/11/2019 DILO Valvesandconnections
122/138
Tubings
Order No.: 3-1026-R002
Suitable connectingparts
3-777-R001
VK/FL-01/20
3-685-R001
VK/A-02/20
VK/B-03/20VK/BG-03/20
Other versions are available.
C 3110-03122
DILO transition pieces and adapters
-
8/11/2019 DILO Valvesandconnections
123/138123
DILO SF6bottle connections
DILO offers a wide range of connec-
tions suitable for all commercial SF6
bottles. Thus safe and quick connec-
tion of hoses of DILO service carts
or SF6gas refilling devices to the SF
6
gas bottles is guaranteed. This refers
to bottle connections for new gas as
well as for reuse gas.
The suitable connecting parts must be
ordered separately.
C 3834-00
DILO SF6bottle connections
3-316-R001 SF6bottle connection 124
3-858-R001 Angle SF6bottle connection 125
3-643-R001 Chinese SF6bottle connection 126
3-643-R002 Chinese SF6bottle connection 127
3-245-R001 American SF6bottle connection 1283-334-R002 American SF
6bottle connection 129
3-245-R002 English SF6bottle connection 130
3-245-R004 English SF6bottle connection 131
3-851-R002 Connection for reuse gas bottle 132
3-851-R003 Connection for reuse gas bottle 133
3-858-R002 Angle for connection of reuse gas
bottle
134
6-1037-R050 Storage connecting hose DN20 135
6-1041-R050 Storage connecting hose DN8 136
-
8/11/2019 DILO Valvesandconnections
124/138
PN64 DN8
SF6bottle connection W21.80x1/14 -DIN 477 No. 6
C 3834-00
Order No.: 3-316-R001 P
Material:Stainless steel / Brass
SF6bottle
Suitable connectingparts
3-365-R008
124
DILO SF6bottle connections
-
8/11/2019 DILO Valvesandconnections
125/138125
PN64 DN8
Angle SF6bottle connection W21.80x1/14 -DIN 477 No. 6
C 3834-00
Order No.: 3-858-R001 P
Material:Brass
600 l SF6container
Suitable connectingparts
3-316-R001
-
8/11/2019 DILO Valvesandconnections
126/138
Order No.: 3-643-R001 P
Material:Brass
PN64 DN8
Chinese SF6bottle connection G 5/8 -
DIN 477 No. 7
C 3834-00
Chinese SF6bottle
Suitable connectingparts
3-393-R...
126
DILO SF6bottle connections
-
8/11/2019 DILO Valvesandconnections
127/138127
Order No.: 3-643-R002 P
Material:Stainless steel / Brass
PN64 DN8
Chinese SF6bottle connection G 5/8 -
DIN 477 No. 7
C 3834-00
Chinese SF6bottle
Suitable connectingparts
3-365-R008
-
8/11/2019 DILO Valvesandconnections
128/138
Order No.: 3-245-R001 P
Material:Brass
C 3834-00
PN64 DN8
American SF6bottle connection0.960-14NGO-LH-EXT - CGA 590
American SF6bottle
Suitable connectingparts
3-393-R...
128
DILO SF6bottle connections
-
8/11/2019 DILO Valvesandconnections
129/138129C 3834-00
PN64 DN8
American SF6bottle connection
0.960-14NGO-LH-EXT - CGA 590
Order No.: 3-334-R002 P
Material:Stainless steel / Brass
American SF6bottle
Suitable connectingparts
3-365-R008
-
8/11/2019 DILO Valvesandconnections
130/138C 3834-00
PN64 DN8
English SF6bottle connection G 5/8 -
BS No. 3
Order No.: 3-245-R002 P
Material:Brass
English SF6bottle
Suitable connectingparts
3-393-R...
130
DILO SF6bottle connections
-
8/11/2019 DILO Valvesandconnections
131/138131
PN64 DN8
English SF6bottle connection G 5/8 -
BS No. 3
C 3834-00
Order No.: 3-245-R004 P
Material:Stainless steel / Brass
English SF6bottle
Suitable connectingparts
3-365-R008
-
8/11/2019 DILO Valvesandconnections
132/138
Order No.: 3-851-R002 P
Material:Stainless steel / Brass
PN64 DN8
Connection for reuse gas bottle 1 -DIN 477 No. 8
C 3834-00
Suitable connectingparts
3-365-R008
Reuse gas bottle
132
DILO SF6bottle connections
-
8/11/2019 DILO Valvesandconnections
133/138133
Order No.: 3-851-R003 P
Material:Brass
PN64 DN8
Connection for reuse gas bottle 1 -DIN 477 No. 8
C 3834-00
Reuse gas bottle
Suitable connectingparts
3-393-R...
-
8/11/2019 DILO Valvesandconnections
134/138C 3834-00
Order No.: 3-858-R002 P
Material:Brass
PN64 DN8
Angle for connection of reuse gas bottle 1 -DIN 477 No. 8
600 l Reuse container
Suitable connectingparts
3-851-R002
134
DILO SF6bottle connections
-
8/11/2019 DILO Valvesandconnections
135/138135
PN64 DN20
Storage connecting hose DN20
Order No.: 6-1037-R050
Suitable connectingparts
3-777-R001
VK/FL-01/20
3-685-R001
VK/A-02/20
VK/B-03/20VK/BG-03/20
C 3834-00
SF6bottle
-
8/11/2019 DILO Valvesandconnections
136/138
Order No.: 6-1041-R050
PN64 DN8
Storage connecting hose DN8
C 3834-00
Suitable connectingparts
3-778-R001
SK-272-R001 / R003
VK/A-02/8
VK/B-03/8VK/BG-03/8
SF6bottle
136
DILO SF6bottle connections
-
8/11/2019 DILO Valvesandconnections
137/138137
For your notes
-
8/11/2019 DILO Valvesandconnections
138/138
SF6gas handling
Besides SF6
couplings and valves DILO supplies a wide range
of devices for SF6
gas handling.
For further information please ask for our special leaflet.