digital angle rule ref. dar/200 battery fitting … · rotate the rule to measure the angle. li-lon...
TRANSCRIPT
DIGITAL ANGLE RULE REF. DAR/200Thank you for purchasing this Trend product which should give lasting performance if used in accordance with these instructions.
INTENDED USEThis accessory is intended to be used to measure the angle and length of a component.
SAFETY Read and understand the instruction sheet carefully before using. This is a sensitive precision tool. Do not disassemble or drop it. Please note the sharp edges, avoid scratching. Store out of reach of children. Do not use as a toy or as a weapon.PLEASE KEEP THESE INSTRUCTIONS IN A SAFE PLACE.
732
ND
S
MM
MM
1020
3040
5060
7080
90100
110120
130140
65
43
3 2 14567
2
MM10220230240250260270280290300310320330340350360370380390
35m
m
Hangingholes
Locking knob
Battery container
Ruler
LCD
200mm 2.5mm
8mm
200m
m
20mm
130 140
2
ZERO
ON
OFF
Tighten
Loosen
130 140
2
ZERO
ON
OFF
Push
Negativepoleuppermost
130 140
2
ZERO
ON
OFF
Pull
130 140
2
ZERO
ON
OFF
Push
ZERO
ON
OFF ON/OFF button
ZERO button
1. Short press ON/OFF to turn on, close up both rulers and place on the flat surface, make sure both ruler’s edges touch the surface, press ZERO button to set zero.
PP C
/DAR
/200
v1.
0
MM
321 4 5 6 7
MM 10 220 230 240 250 260 270 280 290 300 310 320 330 340 350 360 370 380 390
7 32NDS
MM 10 20 30 40 50 60 70 80 90 100 110 120 130 140
6 5 4 3 2 MM
10
7”
400mmMetric Scale (standard rule)
Imperial Scale
7”
MM
321 4 5 6 7
MM 10 220 230 240 250 260 270 280 290 300 310 320 330 340 350 360 370 380 390
7
MM 10 20 30 40 50 60 70 80 90 100 110 120 130 140
6 5 4 3 2 MM
10
7
MM
MM
1020
3040
5060
7080
90100
110120
130140
65
43
3 2 14567
2
MM10220230240250260270280290300310320330340350360370380390
7
MM 10 20 30 40 50 60 70 80 90 100 110 120 130 140
6 5 4 3 2 MM
10
7
MM 10 20 30 40 50 60 70 80 90 100 110 120 130 140
6 5 4 3 2 MM
10
MM
3
2
1
4
5
6
7
MM1022
023
024
025
026
027
028
029
030
031
032
033
034
035
036
037
038
039
0
7
MM 10 20 30 40 50 60 70 80 90 100 110 120 130 140
6 5 4 3 2 MM
10
MM
3
2
1
4
5
6
7
MM1022
023
024
025
026
027
028
029
030
031
032
033
034
035
036
037
038
039
0
2. Rotate the rule to measure the angle.
Li-lon
Battery Fitting and Replacementn To fit or replace battery push the tab on
the bottom of the LCD. The edge of the battery container will appear on the opposite side of the LCD.
n Pull the battery container out.
n Remove the old battery. Insert the new battery type CR2032 3v.
n Ensure the negative pole of the battery is uppermost. The positive pole is on the underside of the battery.
n Push the battery container back in.
Denotes risk of personal injury, loss of life or damage to the tool in case of nonobservance of the instructions.
The attention of UK users is drawn to The Provision and Use of Work Equipment Regulations 1998, and any subsequent amendments. Users should also read the HSE/HSC Safe Use of Woodworking Machinery Approved Code of Practice and Guidance Document and any amendments. Users must be competent in woodworking equipment before using our products.
n Rotate clockwise to tighten the moving rule.
n Rotate anti-clockwise to loosen the moving rule.
TROUBLE SHOOTINGProblem Possible Cause SolutionNo display or Lower voltage, no battery or Reinstall battery orambiguous reading. incorrect installation of battery. replace battery.
Erratic display. Misfunction caused Press zero to reset by high vibration or heavy zero. swinging of rule.
Number skip or Internal error. Remove battery, wait onefrozen display. minute and replace.
MAINTENANCEThe rule has been designed to operate for a long period of time with the minimum of maintenance. Continual satisfactory operation depends upon proper tool care and regular cleaning.
Cleaningn Clean with mild liquid soap and damp cloth. Dry with soft cloth. Never immerse in water. Rule requires no additional lubrication.
Storagen Return to packaging after use if it is not to be used for a long time. Store rule in a dry and shady place. Never leave it outside or in a wet environment. Before storing, it is recommended to wipe surfaces with an anti-rust oil.
GUARANTEEAll Trend products are guaranteed against any defects in either workmanship or material, except products that have been damaged due to improper use or maintenance.
ENVIRONMENTAL PROTECTIONRecycle raw materials instead of disposing as waste. Packaging should be sorted for environmental-friendly recycling. The product, at the end of it’s life, should be sorted for environmental-friendly recycling.
Batteries and the Environment This unit uses Lithium Ion (Li-Ion) batteries. When battery pack needs replacing, we recommend the following: Discharge the energy from the batteries by running them down completely and then remove from the tool.
Li-Ion cells are recyclable so do not throw them away with household waste. They may end up in an incinerator or landfill, which must be avoided. Instead, take the batteries to a Trend Service Agent, your local Trend Stockist or a local recycling station. If necessary contact your local municipality for disposal information. The collected batteries will be disposed of properly and/or used for recycling purposes.
DESCRIPTION OF PARTS
Battery Care WARNING! Insert battery correctly. Keep batteries away from children. Donot swallow, open, recharge, or expose to water, fire or high temperature: may explode, leak and cause damage.
CONFORMITY DECLARATIONThis product conforms with EMC Directive 2004/108/EC.
TECHNICAL DATAMeasuring Range: 000.0° - 999.9° (more than 999.9° will show incorrect display)Working Temperature: 0°C to +50°C Working Humidity: 85% RHWorking Current: 50 uA Resolution: 0.1° Accuracy: 0.3°Battery: CR2032 3V Lithium Battery Weight: 162g
Measuring Obtuse Angles
2. Rotate the rule to measure the angle.
1. Short press ON/OFF to turn on, open up both rulers and place on the flat surface, make sure both ruler’s edges touch the surface, press ZERO button to set zero.
135º
45º
ON/OFF button: Short press ON/OFF to turn on, or alternatively move the scale to turn on the device when at off LCD status. Short press ON/OFF to turn off the LCD. Long press ON/OFF for more than 3 seconds to
shut off the whole system. Automatically turns off in 6 minutes. ZERO button: Press ZERO to set zero at any point when turned on.
OPERATION
Measuring Acute Angles
DIGITAL ANGLE RULE REF. DAR/200Thank you for purchasing this Trend product which should give lasting performance if used in accordance with these instructions.
INTENDED USEThis accessory is intended to be used to measure the angle and length of a component.
SAFETY Read and understand the instruction sheet carefully before using. This is a sensitive precision tool. Do not disassemble or drop it. Please note the sharp edges, avoid scratching. Store out of reach of children. Do not use as a toy or as a weapon.PLEASE KEEP THESE INSTRUCTIONS IN A SAFE PLACE.
732
ND
S
MM
MM
1020
3040
5060
7080
90100
110120
130140
65
43
3 2 14567
2
MM10220230240250260270280290300310320330340350360370380390
35m
m
Hangingholes
Locking knob
Battery container
Ruler
LCD
200mm 2.5mm
8mm
200m
m
20mm
130 140
2
ZERO
ON
OFF
Tighten
Loosen
130 140
2
ZERO
ON
OFF
Push
Negativepoleuppermost
130 140
2
ZERO
ON
OFF
Pull
130 140
2
ZERO
ON
OFF
Push
ZERO
ON
OFF ON/OFF button
ZERO button
1. Short press ON/OFF to turn on, close up both rulers and place on the flat surface, make sure both ruler’s edges touch the surface, press ZERO button to set zero.
PP C
/DAR
/200
v1.
0
MM
321 4 5 6 7
MM 10 220 230 240 250 260 270 280 290 300 310 320 330 340 350 360 370 380 390
7 32NDS
MM 10 20 30 40 50 60 70 80 90 100 110 120 130 140
6 5 4 3 2 MM
10
7”
400mmMetric Scale (standard rule)
Imperial Scale
7”
MM
321 4 5 6 7
MM 10 220 230 240 250 260 270 280 290 300 310 320 330 340 350 360 370 380 390
7
MM 10 20 30 40 50 60 70 80 90 100 110 120 130 140
6 5 4 3 2 MM
10
7
MM
MM
1020
3040
5060
7080
90100
110120
130140
65
43
3 2 14567
2
MM10220230240250260270280290300310320330340350360370380390
7
MM 10 20 30 40 50 60 70 80 90 100 110 120 130 140
6 5 4 3 2 MM
10
7
MM 10 20 30 40 50 60 70 80 90 100 110 120 130 140
6 5 4 3 2 MM
10
MM
3
2
1
4
5
6
7
MM1022
023
024
025
026
027
028
029
030
031
032
033
034
035
036
037
038
039
0
7
MM 10 20 30 40 50 60 70 80 90 100 110 120 130 140
6 5 4 3 2 MM
10
MM
3
2
1
4
5
6
7
MM1022
023
024
025
026
027
028
029
030
031
032
033
034
035
036
037
038
039
0
2. Rotate the rule to measure the angle.
Li-lon
Battery Fitting and Replacementn To fit or replace battery push the tab on
the bottom of the LCD. The edge of the battery container will appear on the opposite side of the LCD.
n Pull the battery container out.
n Remove the old battery. Insert the new battery type CR2032 3v.
n Ensure the negative pole of the battery is uppermost. The positive pole is on the underside of the battery.
n Push the battery container back in.
Denotes risk of personal injury, loss of life or damage to the tool in case of nonobservance of the instructions.
The attention of UK users is drawn to The Provision and Use of Work Equipment Regulations 1998, and any subsequent amendments. Users should also read the HSE/HSC Safe Use of Woodworking Machinery Approved Code of Practice and Guidance Document and any amendments. Users must be competent in woodworking equipment before using our products.
n Rotate clockwise to tighten the moving rule.
n Rotate anti-clockwise to loosen the moving rule.
TROUBLE SHOOTINGProblem Possible Cause SolutionNo display or Lower voltage, no battery or Reinstall battery orambiguous reading. incorrect installation of battery. replace battery.
Erratic display. Misfunction caused Press zero to reset by high vibration or heavy zero. swinging of rule.
Number skip or Internal error. Remove battery, wait onefrozen display. minute and replace.
MAINTENANCEThe rule has been designed to operate for a long period of time with the minimum of maintenance. Continual satisfactory operation depends upon proper tool care and regular cleaning.
Cleaningn Clean with mild liquid soap and damp cloth. Dry with soft cloth. Never immerse in water. Rule requires no additional lubrication.
Storagen Return to packaging after use if it is not to be used for a long time. Store rule in a dry and shady place. Never leave it outside or in a wet environment. Before storing, it is recommended to wipe surfaces with an anti-rust oil.
GUARANTEEAll Trend products are guaranteed against any defects in either workmanship or material, except products that have been damaged due to improper use or maintenance.
ENVIRONMENTAL PROTECTIONRecycle raw materials instead of disposing as waste. Packaging should be sorted for environmental-friendly recycling. The product, at the end of it’s life, should be sorted for environmental-friendly recycling.
Batteries and the Environment This unit uses Lithium Ion (Li-Ion) batteries. When battery pack needs replacing, we recommend the following: Discharge the energy from the batteries by running them down completely and then remove from the tool.
Li-Ion cells are recyclable so do not throw them away with household waste. They may end up in an incinerator or landfill, which must be avoided. Instead, take the batteries to a Trend Service Agent, your local Trend Stockist or a local recycling station. If necessary contact your local municipality for disposal information. The collected batteries will be disposed of properly and/or used for recycling purposes.
DESCRIPTION OF PARTS
Battery Care WARNING! Insert battery correctly. Keep batteries away from children. Donot swallow, open, recharge, or expose to water, fire or high temperature: may explode, leak and cause damage.
CONFORMITY DECLARATIONThis product conforms with EMC Directive 2004/108/EC.
TECHNICAL DATAMeasuring Range: 000.0° - 999.9° (more than 999.9° will show incorrect display)Working Temperature: 0°C to +50°C Working Humidity: 85% RHWorking Current: 50 uA Resolution: 0.1° Accuracy: 0.3°Battery: CR2032 3V Lithium Battery Weight: 162g
Measuring Obtuse Angles
2. Rotate the rule to measure the angle.
1. Short press ON/OFF to turn on, open up both rulers and place on the flat surface, make sure both ruler’s edges touch the surface, press ZERO button to set zero.
135º
45º
ON/OFF button: Short press ON/OFF to turn on, or alternatively move the scale to turn on the device when at off LCD status. Short press ON/OFF to turn off the LCD. Long press ON/OFF for more than 3 seconds to
shut off the whole system. Automatically turns off in 6 minutes. ZERO button: Press ZERO to set zero at any point when turned on.
OPERATION
Measuring Acute Angles
Calculates angles quickly & accurately. n Digital display for
angles. n Stainless steel rule
with metric/imperial scale.
n Measuring range from 000.0° to 360.0° with an accuracy of 0.3°.
n Rule locking function.n Ideal for woodworking,
construction & machining.
TM
DAR/200
DAR/200
TM
Trend Machinery & Cutting Tools Ltd.
Tel: 0044(0)1923 [email protected]
Trend Routing Technology Inc.
Tel: 0044(0)1923 [email protected]
GB
USA
Our policy of continuous improvements mean that specifications may change without notice. Trend Machinery & Cutting Tools Ltd. cannot be held liable for any material rendered unusable, or for any form of consequential loss.
© Copyright Trend 2010. E&OE. ® All trademarks acknowledged.
Li-lon
External Angle Finder
Internal Angle FinderAngle Finder
Rule
ANGLERULE400mm(2x200mm)
DIGITALn Easy operation
with two press buttons.
n Auto-shut off in 6 minutes.
n Includes CR2032 3v Lithium battery.
DIGITAL ANGLERULE400mm(2x200mm)