digital active infrared sensor instruction manual · digital active infrared sensor sbt - 40s sbt -...
TRANSCRIPT
DIGITAL ACTIVE INFRARED SENSOR
SBT - 40S
SBT - 60S
SBT - 80S
SBT-100S
SBT - 30S
38mmφ ~ 50mmφ
INSTRUCTION MANUAL
SUGGESTIONS FOR INSTALLATION 12
1 PARTS DESCRIPTION
Connection Terminal
① LED
VerticalAdjustment Screw
③ Obscuration Time Adjustment (Only for Receiver)
② Monitor Jack (Only for Receiver)
Tamper
Viewfinder
Horizontal AngleAdjustment Dial
Cover Lock Screw
LENS
MAIN BODYCOVER
Wire Hole
RECEIVER
GOOD LEVEL ALARM
TRANSMITTER
POWER
SUGGESTIONS FOR INSTALLATION 23
0.7~
1.0m
14mm33mm
33mm
Spread of Beam
Model
SBT-30S
SBT-100S
SBT-80S
30m
80m
100m 3.0m
2.4m
0.9m
SBT-60S 60m 1.8m
SBT-40S 40m 1.2m
Protection Distance
Note that here the protection distances refers to the sheet below.
Protection Distance
Sp
rea
d
of
Be
am
Height of installation and protection distance
4 INSTALLATION
1. Loosen screw holding cover and remove the cover.
3. Break knock-out and pull wire through.
4. Attach the unit to the wall. 5. Connect wires to the terminal.
Wiring distance
WALL MOUNT
TERMINAL CONFIGURATION
1 2 3 4 5 6 7
POWER ALARM
RECEIVER
TAMPER
1 2 3 4 5 6 7
TRANSMITTER
POWER FREE TAMPER
knock-out
SBT-30S SBT-40S SBT-60S SBT-80/100S
24V 12V 24V 12V 24V 12V 24V
2400m
4400m
7000m
10000m
280m
1120m
780m
500m
2
φ
2
φ
2
φ
2
φ
12V
0.3mm ( 0.6)f
0.5mm ( 0.8)f
0.75mm ( 1.0)f
1.25mm ( 1.2)f
2300m
4200m
6700m
9570m1074m
747m
477m
2100m
3800m
6100m
8700m
250m
980m
680m
430m
270m 1600m
3000m
4900m
7000m
190m
784m
546m
350m
Model
VoltageWirediameter
Each bracket to be reversely attached.
1. Pull the wire through the wire hole of the pole.
2. Attach the bracket to the pole with the pole holder.
Bracket Pole holder Pole cover
POLE MOUNT
Pole mount back-to-back
Attach the mounting pattern
guide holes.
2.
Make the optimum optical adjustment6.
① LED
●GOOD ( Green ) ●POWER ( Green )
On when optically aligned
●LEVEL ( Red )
●ALARM
Intensity varies with signal
Alarm indication lamp
Off when optically not aligned
② Monitor jack: Should be used for making the optimum optical axis adjustment
③ Obscuration time adjustment: To be used for setting the obscuration time
( Refer to ' how to use the monitor jack' )
( Refer to ' adjustment of obscuration time ' )
Ensure the sensors line of sight isfree from any false alarm sourcessuch as bushes, trees, etc. ( Payattention to these as they maychange seasonally.)
Ensure the sensors are
firm fixing.mounted on a stable and
Ensure strong sunlight or car
recommended.)
headlights do not shine directly
from the optical axis is not on to the receiver. (Within ±2°
Direction of installation
Horizontally 180°
Vertically 20°
Because angle of reflection mirror is adjustable
±
unit can be installed in various directions.
in 90°horizontally and 10°vertically, the±
paper to the wall, mark theinstallation holes, and make
operation before replacing covers. as per section 5 and confirm system
Transmitter
Receiver
Transmitter
Receiver
Receiver
Transmitter
In case of jump phenomenon, as shown ×
of transmitter and receiver to the following
section in the above, change the disposition
manner shown section.◎
Receiver
Transmitter
10cm
2. Look through the viewfinder as shown below.
Viewfinder
NOTE: After completion of optical adjustment, ensure
Monitor Jack
1. Insert the meter pins into the monitor jack. (Pay attention to the polarity because of DC voltage)
Vertical adjustment
to raise(loosen)
to lower(tighten)
1 5
43
2
ADJUSTMENT OF OBSCURATION
Obscuration time control
CONFIRMATION OF OPERATION
After completion of the installation, confirm correct operation by suitable walk test. Refer to the following LEDindications during the walk test. Confirm tamper operation prior to replacing covers. Confirm system operationwith covers replaced.
Transmitter
Receiver
Conditions
Transmitting
Watching
Alarm
Indication
Green LED is on
Alarm indicator is off
Alarm indicator is on
NOTE: Conduct a Walk Test at least once a year
OUTLINE DIMENSION
9TROUBLE SHOOTING GUIDE SPECIFICATION
Model SBT-30S SBT-40S SBT-60S SBT-80S SBT-100S
Protection range(outdoor)
Distance allowance
5-30m 30-40m 40-60m 60-80m 80-100m
350m 450m 650m 900m 1100m
Infrared beam
Detection system
Light source
Response time
Alarm output
Power required
Power consumption
Temperature range
Tamper output
Optical axis horizontal adjust
Optical axis vertical adjust
Collimator
Measure for moisture/frost
Other additional function
Place for installation
Weight
2 beams
2 beams simultaneous cut-off detection
Infrared LED
50-700 msec
Relay contact, form 'C' contact rating 30V AC, DC 0.5A Max.
DC 10.5-28V
40mA maxDC12-28V
45mA maxDC12-28V
55mA maxDC12-28V
65mA maxDC12-28V
65mA maxDC12-28V
-25℃~+55℃
Normally closed voltage free contacts 30V DC, 0.5 A Max.
±90°
±10°
Finder ( peep window )
Slit type cover, heater option
Sensitivity monitoring output terminal. Ok monitoring
Indoor or Outdoor
600g ( Transmitter and Receiver )
82
60
146
171
2- 4.0mm
2- 5.0mm
38~50mm
Pole77
Caution: Obscuration time settings exceeding 70msec (exceeding a setting of 1) do
Set the obscuration time of the receiver by adjusting the obscuration time control
conditions where there are a lot of birds or wind blown material.
5 ADJUSTMENT OF OPTICAL AXIS
It is important to ensure correct optical alignment between the transmitter and receiver for proper operation.
HOW TO USE THE MONITOR JACK
The best adjustment of optical axis can be done by reading the output voltage of the monitor jack.
7
10
W.97.0067
6
8
Turn on the power supply after uninstallation.1. Adjust the angle of the lens via the Horizontal angle3.
Possible cause A Remedy
Indication lamp of Transmitterdoes not light.
Improper voltage of power supply Check power supply and wiring
Power supply indication Lampof Receiver does not light.
Improper voltage of power supply Check power supply and wiring
Alarm indication lamp does notlight even when the beams areintercepted.
②
Remove the reflecting object or
Check two beams to interceptat the same time.Adjust obscuration time setting to be shorter.
Although alarm LED lights
①
Melted bridge on the signal
Check the wiring.
It needs to be repaired.
Alarm LED on the Receiver does not turn off.
Inadequate optical axis.Shading objects between the
of the T ransmitter and/or Receiver.
Readjust the optical axis.
Remove the shading objects.
Clean optics with soft cloth.
Bad wiring connection.Change of supply voltage.
Shading objects moving by wind
Unstable installation of the sensorunit.Incomplete optical axis adjustment.
Birds and other large flying objectsintercept the beam.
Check the wiring connection.
Check the voltage (for stabilizedsupply voltage.) Remove the shading objects or
Fix steadily.
Readjust the optical axis.
Readjust the obscuration timeto be longer or reposition.
① Infrared beam from Transmitter is
sent into the Receiver.
Shorter o bscuration t ime t han t hat③
Q Symptom
Intermittent alarm.
Place the viewfinder on either right or lefthand side of the lens whichever makeseasier viewing.
the sensor can be seen in the center of the Viewfinder.
adjustment and the Vertical adjustment screw so that
and Receiver. Confirm after adjustment that the greenThis adjustment is carried out on both the Transmitter
GOOD LED is on, otherwise alignment should bereadjusted. The red LEVEL LED lamp will be brighterdependent on higher signal levels.
that both filters on the receiver are replacedto their original position behind the mirrors.
NOTE: If the sensors are too close together then the signal level saturates and
2. a) Adjust the horizontal adjustment until the output is at a maximum. b) Adjust the vertical adjustment screw to obtain best signal. (Do not interrupt beam by hands during the adjustment)
3. The following minimum voltages should be obtained to ensure best performance.2.3V for all of the SBT-XXS series. If this is not obtained then the transmitter andreceiver should be re-aligned.
the IR beam may be shut-down. This is normal and will only be achievedduring bench testing. Signal levels are restored under normal operation
distances.
Scale 1
fast running at full
Scale 2 Scale 3 Scale 4
walking with quick normal walking slow actionspeed(6.9m/s) steps(1.2m/s) (0.7m/s) (0.3~0.5m/s)
to the required setting according to the sketch beside. The obscuration time shouldbe set lower to detect faster moving targets, however care should be taken to notethe environmental conditions as the obscuration time should be set higher to ignore
not comply with the requirements in UL639, Instrusion Detection Units.
intercepted, alarm doeswhen the beams are
not ring.
reflected on another object and Two beams are not intercepted at
set on the obscuration control.
the same time.
Broken wires or short on the
(Wrong current on the signal wires)connection
②signal wires.
Transmitter and the Receiver.Dirty cover or dirty reflection mirror
②
③
between the Transitter and theReceiver.
①
②
③
④
⑤
⑥
①
②
①
①
③
②
②
③
①
②
③
④
⑤
⑥
①
change the place for installationand the optical axis direction.
change the place for installation.
SHENZHEN SUNWAVE ELECTRONICS CO., LTD.
http://www.sunwave.cc
CHINA
TEL: +86-755-8998-3101 FAX: +86-755-8998-3102
No.21 Plant, Da Wei Industrial Zone, Huang Ge
Heng Gang Town, Shenzhen
Keng,