dball-dball2-ford4-rsr en ig pga20160314
TRANSCRIPT
Index
Installation Guide
Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.
® Ford is a registered trademark and property of its respective company.
Vehicle Application Guide................................................................................................................................................Key2GO programming.....................................................................................................................................................
Installation (Wiring Diagrams & Vehicle Wiring Reference Charts)Type 1..............................................................................................................................................................................Type 1 with T-Harness THFD1........................................................................................................................................Type 2..............................................................................................................................................................................Type 2 with T-Harness THFD1........................................................................................................................................Type 3..............................................................................................................................................................................Type 3 with T-Harness THFD1........................................................................................................................................Type 4..............................................................................................................................................................................Type 4 with T-Harness THFD1........................................................................................................................................
SmartStart/XL202 Installation Notes...............................................................................................................................
ProgrammingModule Programming......................................................................................................................................................Module Reset................................................................................................................................................................... Hard Reset.......................................................................................................................................................................Feature and Option List...................................................................................................................................................Feature Programming......................................................................................................................................................
LED Diagnostics and Troubleshooting............................................................................................................................
Limited One-Year Consumer Warranty............................................................................................................................Quick Reference Guide...................................................................................................................................................
0202
0304060709101213
15
1619192020
21
2223
Important!This guide is compatible with the FORD4 firmware version 2.31 and higher.This product is NOT compatible with vehicles equipped with a manual transmission.
Remote Start Ready (RSR) is a function that enables the to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance.
SmartStart CompatibleSmartStart is equipped with D2D, which means it can be connected to an interface module and used in Remote Start Ready (RSR) mode without the use of a remote starter. See the Module Programming section for more information.
Data override and door lock interface compatible with specific Ford vehicles equipped with SA type keys. Some of the available features include: transponder override, door lock control, factory security control, trunk release, tach sensing, as well as door, hood and trunk sensing.
This solution offers two (2) configuration options to control your system: RF Kit or SmartStart (both sold separately).
Two (2) master keys required for programming when doing a regular installation. One (1) master key required if using Key2GO feature, see page 2 for more information.
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
Page 2
Vehicle Application Guide
The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle.
This feature is required if only one key is available, the installation will remain the same as the two-key method.
Key2GO has been designed and developed to bypass the advanced encryption layers found in modern vehicles. It uses an array of servers to generate a duplicate of the original key, allowing the installation of a remote starter without having to give up a key.
The advantage is that this feature allows you to use one original key and the server, as a proxy for the second key, can be used to configure the bypass in the vehicle.
All Key2GO-compatible firmware are clearly indicated in the function list of each vehicle search result page and will also appear on the flash page. Any first-time user must re-register to gain access to Key2GO, and some additional information will be required to complete the registration process, such as your Directed account number and store name.
Key2GO is compatible with XpressVIP 4.5 or higher and requires an XKLoader.
Refer to page 18 of this guide for instructions on how to program features using Key2GO.
Vehicles
2016
2015
2014
2013
2012
PK
-Im
mobili
zer
Bypass-D
ata
No
Key
Req'd
DL-A
rmF
acto
ryS
ecurity
DL-D
isarm
Facto
ryS
ecurity
DL-D
oor
Lock
Contr
ol
DL-D
oor
Unlo
ck
DL-T
runk
/H
atc
hR
ele
ase
Key2G
O
RS
-RA
PS
hut
Dow
n(R
eta
ined
AC
CP
ow
er)
RS
-Rem
ote
Sta
rtR
eady
RS
-Sm
art
Sta
rt
RS
-Sm
art
Sta
rt3.0
Com
patible
RS
-Tach
/R
PM
Outp
ut
SS
-Entr
yM
onitoring
ALL
Door
Pin
s
SS
-Entr
yM
onitoring
Driver
Door
Pin
SS
-Entr
yM
onitoring
Hood
Pin
SS
-Entr
yM
onitoring
Tru
nk/H
atc
hP
in
ST
-Bra
ke
Sta
tus
(foot
bra
ke)
ST
-Door
Locks
Sta
tus
Ford
C-Max 4 4 4 • • • • • • • • • • • • • • • • •
Escape 1 1 1 1 • • • • • • • • • • • • • • • • •
Focus 4 4 2 2 2 • • • • • • • • • • • • • • • • • •
Transit Connect 3 3 • • • • • • • • • • • • • • • • • •
LEGEND:
DL: OE Door Lock & Alarm Controls
PK: Transponder & Immobilizer Override
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
C2280F
C2280D
C2280H
C2280E
Bro
wn
C2280B
Bro
wn
C2280C
Blu
e
C2280A
Gre
en
C2280G
Gre
en
BCM (passenger side, behind glove box)
1
11
10
20
2
12
3
13
4
14
5
15
6
16
7
17
8
18
9
19
Installation Type 1Page 3
2142
223
324
425
526
627
728
829
930
1031
1132
1233
1334
1435
1536
1637
1738
1839
1940
2041
122
MS CAN High: Tan/Black: 3
HS CAN High: Orange/Green: 5MS CAN Low: Tan: 4
HS CAN Low: Orange/Brown: 6
[1] (-) Unlock 1 Output: Red/Black: 4
(-) Parking Light Output: Blue/Red: 12
(-) Ground: Black: 14(-) Ground(+) 12V: Red: 13
22242
32343
42444
52545
62646
72747
82848
92949
103050
113151
123252
133353
143454
153555
163656
173757
183858
193959
204060
12141
C2280B (BCM)C2280A (BCM)
RAP Off: Orange/Red: 10RAP Off: Yellow/Red: 11
(+) Ignition Output: Yellow: 8
(+) Accessory Output: Gray/Black: 7
TX: Yellow/Black: 10RX: Orange/Black: 11
(+) Start Output: Gray: 6
(-) Lock Output: Green/Black: 2
[1] (-) Unlock 2 Output: Black/White: 1
10
DBALL/DBALL2
RF
Prog. Button
LED
4
14
12
2
Junction Connector(near BCM, rotated view)
Important!The Hood Pin and Remote Start Safety Override Switch are mandatory security devices, but are NOT supplied with the DBALL.
3086
8587
87a
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety Override Switch
6 ampdiodes
Note: hood pin only required on vehicles not equipped with a factory hood pin
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
(+) 12V: Brown: 7
HS CAN High:White/Blue, pin 7(DBALL2 ONLY)
HS CAN Low: White, pin 8
(DBALL2 ONLY)
Warning!
Pins 7 & 8 of the BCM connector should ONLY be connected with DBALL2.
2 22 42
3 23 43
4 24
5 25 45
6 26 46
7 27 47
8 28 48
9 29 49
10 30 50
11 31 51
12 32 52
13 33 53
14 34 54
15 35 55
16 36 56
17 37 57
18 38 58
19 39 59
20 40 60
1 21 41
C2280C (BCM)
44
(+) Parking Lights: Green/Orange or Yellow/Blue, pin 1
MS CAN L: Violet/Orange, pin 40
(+) Parking Lights: Brown/Yellow, pin 26
MS CAN H: Gray/Orange,pin 41
(-) Unlock 2: Blue/Brown,
pin 55
(-) Lock: Gray/Yellow, pin 36
Driver DoorTrigger: Green/Violet, pin 45
(+) Accessory: Violet/Green,pin 44
Data RX: Violet/Gray,
pin 34
(-) Unlock 1: Violet/Orange,
pin 26
(+) Ignition: Brown/Yellow,pin 43
Data TX:Yellow/Orange,pin 54
(+) Starter: Blue/White,
pin 1
1
2
C2280G (BCM)
(+) 12V: Red, pin 2
(+) 12V
Fuse 10A
[2] (-) Trunk/Hatch/Power LiftgateRelease Output: Violet/Brown: 9
(-) Trunk/Hatch Release: Brown, pin 49
1 7
2 8
3 9
4 10
5
6
11
12
Power Liftgate Switch(on dash)
(-) Power Liftgate Output: Gray/Yellow,pin 4
OR
[2] The Trunk/Hatch/Power Liftgate Release connection is only required on the 2014+ Escape (if equipped).
[1] Both unlock wires need to be connected to wake up the system from sleep mode (ONLY on 2013+ Escape without one-touch window control).
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
Page 4
Refer to the Vehicle Wiring Reference Chart on next page for more information on specific wiring and connections.
10
DBALL/DBALL2
RF
Prog. Button
LED
4
14
12
2
Connect to VehicleRefer to the wiring reference chart on next page for more information.
Installation Type 1 with T-Harness (THFD1)
The Remote Start Safety Override Switch MUST be in the OFF position.
Remote Start SafetyOverride Switch
4321
4
1
3
2
[1] (-) Unlock 1 Output: Red/Black
[1] (-) Unlock 2 Output: Black/White
(-) Lock Output: Green/Black
RAP Off: Yellow/Red
RAP Off: Orange/Red
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
HS CAN Low: White, pin 14 (DBALL2 ONLY)
OBDII DiagnosticConnector
1 8
169
MS CAN High: Tan/Black
MS CAN Low: Tan
HS CAN Low: Orange/Brown
HS CAN High: Orange/Green
HS CAN High: White/Blue, pin 6, (DBALL2 ONLY)
THFD1 Rev.2(Optional T-Harness)
(+) Parking Light Output: Brown
(+) 12V: Yellow
(+) Parking Light Output: White
[1] (-) Unlock 1 Output: Red/Black
2142
223
324
425
526
627
728
829
930
1031
1132
1233
1334
1435
1536
1637
1738
1839
1940
2041
122
C2280A (BCM)
Ignition Barrel
P.A.T.S.(black 4-pin connector)
(vehicle side)(vehicle side) Violet
Attention! DO NOT Cut loop in RSR application.
Warning!
Pins 6 & 14 of the OBDII connector should ONLY be connected with DBALL2.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Ignition Switch(black 7-pin connector)
7421 3 5 6 1 432
22 5533 664411 77
22 5533 664411 77
MS CAN High: Gray/Orange, pin 3
MS CAN Low: Violet/Orange, pin 11
(+) Parking Lights: Green/Orange orYellow/Blue, pin 1
(+) Parking Lights: Brown/Yellow,pin 26
1
2
C2280G (BCM)
(+) 12V: Red, pin 2
D2Donly
1 7
2 8
3 9
4 10
5
6
11
12
Driver DoorTrigger: Green/Violet, pin 45
22242
32343
42444
52545
62646
72747
82848
92949
103050
113151
123252
133353
143454
153555
163656
173757
183858
193959
204060
12141
C2280B (BCM)
(-) Unlock 2: Blue/Brown, pin 55
(-) Lock: Gray/Yellow, pin 36
(-) Trunk ReleaseOutput: Brown, pin 49
Power Liftgate Switch(on dash)
(-) Power Liftgate Output: Gray/Yellow,pin 4
OR[2] (-) Trunk/Hatch/Power Liftgate Release Output: Violet/Brown
[2] The Trunk/Hatch/Power Liftgate Release connection is only required on the 2014+ Escape (if equipped).
[1] Both unlock wires need to be connected to wake up the system from sleep mode (ONLY on 2013+ Escape without one-touch window control).
C2280C (BCM)
2 22 42
3 23 43
4 24
5 25 45
6 26 46
7 27 47
8 28 48
9 29 49
10 30 50
11 31 51
12 32 52
13 33 53
14 34 54
15 35 55
16 36 56
17 37 57
18 38 58
19 39 59
20 40 60
1 21 41
44
(-) Unlo
ck 1:
Vio
let/O
ran
ge, p
in 2
6
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
Page 5
Type 1 - Vehicle Wiring Reference Charts
Function Wire Color Pin Polarity Name, Location on vehicle Color No. Pins
MS CAN High (w/o T-Harness) Gray/Orange 41 Data C2280A conn. At BCM located on passenger side behind glove box. Green 42-pin
MS CAN Low (w/o T-Harness) Violet/Orange 40 Data C2280A conn. At BCM located on passenger side behind glove box. Green 42-pin
MS CAN High (w/ T-Harness) Gray/Orange 3 Data Diagnostic Connector (OBDII) White 16-pin
MS CAN Low (w/ T-Harness) Violet/Orange 11 Data Diagnostic Connector (OBDII) White 16-pin
Parking LightsGreen/Orange &
Brown/Yellow1 & 26 (+) C2280A conn. At BCM located on passenger side behind glove box. Green 42-pin
Driver Door Trigger Green/Violet 45 (-) N.C. C2280B conn. At BCM located on passenger side behind glove box. Brown 60-pin
Lock Gray/Yellow 36 (-) C2280B conn. At BCM located on passenger side behind glove box. Brown 60-pin
Unlock 2 * Blue/Brown 55 (-) C2280B conn. At BCM located on passenger side behind glove box. Brown 60-pin
Accessory Violet/Green 44 (+) C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
Data RX Violet/Gray 34 Data C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
Data TX Yellow/Orange 54 Data C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
HS CAN High (w/o T-Harness) White/Blue 7 Data C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
HS CAN Low (w/o T-Harness) White 8 Data C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
HS CAN High (w/ T-Harness) White/Blue 6 Data Diagnostic Connector (OBDII) White 16-pin
HS CAN Low (w/ T-Harness) White 14 Data Diagnostic Connector (OBDII) White 16-pin
Ignition Brown/Yellow 43 (+) C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
Unlock 1 Violet/Orange 26 (-) C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
12V Red 2 (+) C2280G conn. At BCM located on passenger side behind glove box. Green 2-pin
Starter Blue/White 1 (+) Junction conn. Near BCM located on passenger side behind glove box. Black 20-pin
Power Liftgate** Gray/Yellow 4 (-) Power Lift gate, on dash Gray 12-pin
Trunk/Hatch Brown 49 (-) C2280B conn. At BCM located on passenger side behind glove box. Brown 60-pin
* The Unlock 2 connection is only required on the 2013+ Ford Escape without one-touch window control.
** The Trunk Release/Power Liftgate connection is only required in the 2014-2015 Ford Escape. The 2016 Ford Escape Power Liftgate is in data.
Wire Information Connector Information
Ford Escape 2013-2016
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
Installation Type 2Page 6
C2280F
C2280D
C2280H
C2280E
Bro
wn
C2280B
Bro
wn
C2280C
Blu
e
C2280A
Gre
en
C2280G
Gre
en
BCM (passenger side, behind glove box)
(-) Ground
10
DBALL/DBALL2
RF
Prog. Button
LED
4
14
12
2
21
11 1
25
24
23
13 3
20 10
17 716 6
19 9
15 5
18 8
14 4
27
22
12 2
26
JunctionConnector(near BCM)
3086
8587
87a
Important!The Hood Pin and Remote Start Safety Override Switch are mandatory security devices, but are NOT supplied with the DBALL.
22242
32343
42444
52545
62646
72747
82848
92949
103050
113151
123252
133353
143454
153555
163656
173757
183858
193959
204060
12141
C2280B (BCM)
2142
223
324
425
526
627
728
829
930
1031
1132
1233
1334
1435
1536
1637
1738
1839
1940
2041
122
C2280A (BCM)
6 ampdiodes
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety Override Switch
Note: hood pin only required on vehicles not equipped with a factory hood pin
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
(-) Parking Light Output: Blue/Red: 12
(+) Accessory Output: Gray/Black: 7
TX: Yellow/Black: 10
RX: Orange/Black: 11
(+) Start Output: Gray: 6
(-) Lock/Unlock Activation Output: Black/White: 1
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
MS CAN High: Tan/Black: 3
HS CAN High: Orange/Green: 5MS CAN Low: Tan: 4
HS CAN Low: Orange/Brown: 6
(-) Ground: Black: 14(+) 12V: Red: 13
RAP Off: Orange/Red: 10RAP Off: Yellow/Red: 11
(+) Ignition Output: Yellow: 8(+) 12V: Brown: 7
HS CAN High: White/Blue, pin 7 (DBALL2 ONLY)
HS CAN Low: White, pin 8 (DBALL2 ONLY)
Warning!
Pins 7 & 8 of the BCM connector should ONLY be connected with DBALL2.
2 22 42
3 23 43
4 24
5 25 45
6 26 46
7 27 47
8 28 48
9 29 49
10 30 50
11 31 51
12 32 52
13 33 53
14 34 54
15 35 55
16 36 56
17 37 57
18 38 58
19 39 59
20 40 60
1 21 41
C2280C (BCM)
44
(+) Starter: Blue/White,
pin 4(-) Trunk:
Brown, pin 49
Driver Door Trigger: Green/Violet,
pin 45
MS CAN L: Violet/Orange, pin 40
MS CAN H: Gray/Orange,pin 41
(+) Parking Lights:Yellow/Blue, pin 1
(+) Parking Lights:Brown/Yellow, pin 26
(+) Accessory: Violet/Green,pin 44
Data RX: Violet/Gray,
pin 34
(-)Lock/ Unlock: Brown, pin 11
(+) Ignition: Brown/Yellow,pin 43
Data TX:Yellow/Orange,pin 54
1
2
C2280G (BCM)
(+) 12V: Red, pin 2
(+) 12V
Fuse 10A
(-) Trunk/Hatch Activation Output:Violet/Brown: 9
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
Page 7
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Refer to the Vehicle Wiring Reference Chart on next page for more information on specific wiring and connections.
10
DBALL/DBALL2
RF
Prog. Button
LED
4
14
12
2
Connect to VehicleRefer to the wiring referencechart on next page for more
information.
Driver Door Trigger
(-) Lock
(-) Trunk
Installation Type 2 with T-Harness (THFD1)
The Remote Start Safety Override Switch MUST be in the OFF position.
Remote Start SafetyOverride Switch
[1] (-) Trunk Activation Output: Violet/Brown
(+) Parking Light Output: Brown
(+) 12V: Yellow
(+) Parking Light Output: White
(-) Lock/Unlock Activation Output: Black/White
RAP Off: Yellow/Red
RAP Off: Orange/Red
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
2142
223
324
425
526
627
728
829
930
1031
1132
1233
1334
1435
1536
1637
1738
1839
1940
2041
122
C2280A (BCM)
THFD1 Rev.2(Optional T-Harness)
Violet
Attention! DO NOT Cut loop in RSR application.
OBDII DiagnosticConnector
1 8
169
MS CAN High: Tan/Black
MS CAN Low: Tan
HS CAN Low: Orange/Brown
HS CAN High: Orange/Green
Warning!
Pins 6 & 14 of the OBDII connector should ONLY be connected with DBALL2.
4321
4
1
3
2
Ignition Barrel
P.A.T.S.(black 4-pin connector)
(vehicle side)(vehicle side)
Ignition Switch(black 7-pin connector)
7421 3 5 6 1 432
2
2
2
2
5
5
5
5
3
3
3
3
6
6
6
6
4
4
4
4
1
1
1
1
7
7
7
7
(+) Parking Lights: Yellow/Blue, pin 1
(+) Parking Lights: Brown/Yellow, pin 26
HS CAN Low: White, pin 14 (DBALL2 ONLY)
HS CAN High: White/Blue, pin 6, (DBALL2 ONLY)
MS CAN High: Gray/Orange, pin 3
MS CAN Low: Violet/Orange, pin 11
1
2
C2280G (BCM)
(+) 12V: Red, pin 2
D2Donly
[1] The trunk connection is only required on the 2014-15 Focus.
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
Page 8
Type 2 - Vehicle Wiring Reference Chart
Function Wire Color Pin Polarity Name, Location on vehicle Color No. Pins
MS CAN High (w/o T-Harness) Gray/Orange 41 Data C2280A conn. At BCM located on passenger side behind glove box. Green 42-pin
MS CAN Low (w/o T-Harness) Violet/Orange 40 Data C2280A conn. At BCM located on passenger side behind glove box. Green 42-pin
MS CAN High (w/ T-Harness) Gray/Orange 3 Data Diagnostic Connector (OBDII) White 16-pin
MS CAN Low (w/ T-Harness) Violet/Orange 11 Data Diagnostic Connector (OBDII) White 16-pin
Parking LightsYellow/Blue &
Brown/ Yellow1 & 26 (+) C2280A conn. At BCM located on passenger side behind glove box. Green 42-pin
Driver Door Trigger Green/Violet 45 (-) N.C. C2280B conn. At BCM located on passenger side behind glove box. Brown 60-pin
Trunk Release Brown 49 (-) C2280B conn. At BCM located on passenger side behind glove box. Brown 60-pin
Accessory Violet/Green 44 (+) C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
Data RX Violet/Gray 34 Data C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
Data TX Yellow/Orange 54 Data C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
HS CAN High (w/o T-Harness) White/Blue 7 Data C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
HS CAN Low (w/o T-Harness) White 8 Data C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
HS CAN High (w/ T-Harness) White/Blue 6 Data Diagnostic Connector (OBDII) White 16-pin
HS CAN Low (w/ T-Harness) White 14 Data Diagnostic Connector (OBDII) White 16-pin
Ignition Brown/Yellow 43 (+) C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
Lock/Unlock Brown 11 (-) C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
12V Red 2 (+) C2280G conn. At BCM located on passenger side behind glove box. Green 2-pin
Starter Blue/White 4 (+) Junction conn. Near BCM located on passenger side behind glove box. Black 20-pin
Wire Information Connector Information
Ford Focus 2012-2014
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
Installation Type 3Page 9
C2280F
C2280D
C2280H
C2280E
Bro
wn
C2280B
Bro
wn
C2280C
Blu
e
C2280A
Gre
en
C2280G
Gre
en
BCM (passenger side, behind glove box)
(-) Ground
10
DBALL/DBALL2
RF
Prog. Button
LED
4
14
12
2
21
11 1
25
24
23
13 3
20 10
17 716 6
19 9
15 5
18 8
14 4
27
22
12 2
26
JunctionConnector(near BCM)
3086
8587
87a
Important!The Hood Pin and Remote Start Safety Override Switch are mandatory security devices, but are NOT supplied with the DBALL.
22242
32343
42444
52545
62646
72747
82848
92949
103050
113151
123252
133353
143454
153555
163656
173757
183858
193959
204060
12141
C2280B (BCM)
2142
223
324
425
526
627
728
829
930
1031
1132
1233
1334
1435
1536
1637
1738
1839
1940
2041
122
C2280A (BCM)
6 ampdiodes
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety Override Switch
Note: hood pin only required on vehicles not equipped with a factory hood pin
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
(-) Parking Light Output: Blue/Red: 12
(-) Trunk Activation Output: Violet/Brown: 9
(+) Accessory Output: Gray/Black: 7
TX: Yellow/Black: 10
RX: Orange/Black: 11
(+) Starter Output: Gray: 6
(-) Unlock Output: Black/White: 1
(-) Lock Output: Green/Black: 2
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
MS CAN High: Tan/Black: 3
HS CAN High: Orange/Green: 5MS CAN Low: Tan: 4
HS CAN Low: Orange/Brown: 6
(-) Ground: Black: 14(+) 12V: Red: 13
RAP Off: Orange/Red: 10RAP Off: Yellow/Red: 11
(+) Ignition Output: Yellow: 8(+) 12V: Brown: 7
HS CAN High: White/Blue, pin 7 (DBALL2 ONLY)
HS CAN Low: White, pin 8 (DBALL2 ONLY)
Warning!
Pins 7 & 8 of the BCM connector should ONLY be connected with DBALL2.
2 22 42
3 23 43
4 24
5 25 45
6 26 46
7 27 47
8 28 48
9 29 49
10 30 50
11 31 51
12 32 52
13 33 53
14 34 54
15 35 55
16 36 56
17 37 57
18 38 58
19 39 59
20 40 60
1 21 41
C2280C (BCM)
44
(+) Starter: Blue/White,
pin 4(-) Trunk:
Brown, pin 49
(-) Lock: Gray/
Yellow, pin 36
Driver Door Trigger: Green/Violet,
pin 45
MS CAN Low:Violet/Orange,
pin 40
MS CAN High:Gray/Orange,
pin 41
(+) Parking Lights:Yellow/Blue, pin 1
(+) Parking Lights:Brown/Yellow, pin 26
(+) Accessory: Violet/Green,pin 44
Data RX: Violet/Gray,
pin 34
(-) Unlock: Brown, pin 26
(+) Ignition: Brown/Yellow,pin 43
Data TX:Yellow/Orange,pin 54
1
2
C2280G (BCM)
(+) 12V: Red, pin 2
(+) 12V
Fuse 10A
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
Page 10
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Refer to the Vehicle Wiring Reference Chart on next page for more information on specific wiring and connections.
10
DBALL/DBALL2
RF
Prog. Button
LED
4
14
12
2
Connect to VehicleRefer to the wiring referencechart on next page for more
information.
Driver Door Trigger
(-) Lock
(-) Trunk
Installation Type 3 with T-Harness (THFD1)
The Remote Start Safety Override Switch MUST be in the OFF position.
Remote Start SafetyOverride Switch
(-) Trunk Activation Output: Violet/Brown
(+) Parking Light Output: Brown
(+) 12V: Yellow
(+) Parking Light Output: White
(-) Lock/Unlock Activation Output: Black/White
RAP Off: Yellow/Red
RAP Off: Orange/Red
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
2142
223
324
425
526
627
728
829
930
1031
1132
1233
1334
1435
1536
1637
1738
1839
1940
2041
122
C2280A (BCM)
THFD1 Rev.2(Optional T-Harness)
Violet
Attention! DO NOT Cut loop in RSR application.
OBDII DiagnosticConnector
1 8
169
MS CAN High: Tan/Black
MS CAN Low: Tan
HS CAN Low: Orange/Brown
HS CAN High: Orange/Green
Warning!
Pins 6 & 14 of the OBDII connector should ONLY be connected with DBALL2.
4321
4
1
3
2
Ignition Barrel
P.A.T.S.(black 4-pin connector)
(vehicle side)(vehicle side)
Ignition Switch(black 7-pin connector)
7421 3 5 6 1 432
2
2
2
2
5
5
5
5
3
3
3
3
6
6
6
6
4
4
4
4
1
1
1
1
7
7
7
7
(+) Parking Lights: Yellow/Blue, pin 1
(+) Parking Lights: Brown/Yellow, pin 26
HS CAN Low: White, pin 14 (DBALL2 ONLY)
HS CAN High: White/Blue, pin 6, (DBALL2 ONLY)
MS CAN High: Gray/Orange, pin 3
MS CAN Low: Violet/Orange, pin 11
1
2
C2280G (BCM)
(+) 12V: Red, pin 2
D2Donly
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
Page 11
Type 3 - Vehicle Wiring Reference Chart
Function Wire Color Pin Polarity Name, Location on vehicle Color No. Pins
MS CAN High (w/o T-Harness) Gray/Orange 41 Data C2280A conn. At BCM located on passenger side behind glove box. Green 42-pin
MS CAN Low (w/o T-Harness) Violet/Orange 40 Data C2280A conn. At BCM located on passenger side behind glove box. Green 42-pin
MS CAN High (w/ T-Harness) Gray/Orange 3 Data Diagnostic Connector (OBDII) White 16-pin
MS CAN Low (w/ T-Harness) Violet/Orange 11 Data Diagnostic Connector (OBDII) White 16-pin
Parking LightsYellow/Blue &
Brown/ Yellow1 & 26 (+) C2280A conn. At BCM located on passenger side behind glove box. Green 42-pin
Driver Door Trigger Green/Violet 45 (-) N.C. C2280B conn. At BCM located on passenger side behind glove box. Brown 60-pin
Lock Gray/Yellow 36 (-) C2280B conn. At BCM located on passenger side behind glove box. Brown 60-pin
Trunk Release Brown 49 (-) C2280B conn. At BCM located on passenger side behind glove box. Brown 60-pin
Accessory Violet/Green 44 (+) C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
Data RX Violet/Gray 34 Data C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
Data TX Yellow/Orange 54 Data C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
HS CAN High (w/o T-Harness) White/Blue 7 Data C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
HS CAN Low (w/o T-Harness) White 8 Data C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
HS CAN High (w/ T-Harness) White/Blue 6 Data Diagnostic Connector (OBDII) White 16-pin
HS CAN Low (w/ T-Harness) White 14 Data Diagnostic Connector (OBDII) White 16-pin
Ignition Brown/Yellow 43 (+) C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
Unlock Violet/Gray 26 (-) C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
Starter Blue/White 4 (+) Junction conn. Near BCM located on passenger side behind glove box. Black 27-pin
Wire Information Connector Information
Ford Transit Connect 2014-2015
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
C2280F
C2280D
C2280H
C2280E
Bro
wn
C2280B
Bro
wn
C2280C
Blu
e
C2280A
Gre
en
C2280G
Gre
en
BCM (passenger side, behind glove box)
1
11
10
20
2
12
3
13
4
14
5
15
6
16
7
17
8
18
9
19
Installation Type 4Page 12
2142
223
324
425
526
627
728
829
930
1031
1132
1233
1334
1435
1536
1637
1738
1839
1940
2041
122
MS CAN High: Tan/Black: 3
HS CAN High: Orange/Green: 5
MS CAN Low: Tan: 4
HS CAN Low: Orange/Brown: 6
(-) Unlock 1 Output: Red/Black: 4
(-) Parking Light Output: Blue/Red: 12
(-) Ground: Black: 14(-) Ground
(+) 12V: Red: 13
22242
32343
42444
52545
62646
72747
82848
92949
103050
113151
123252
133353
143454
153555
163656
173757
183858
193959
204060
12141
C2280B (BCM)C2280A (BCM)
RAP Off: Orange/Red: 10
RAP Off: Yellow/Red: 11
(+) Ignition Output: Yellow: 8
(+) Accessory Output: Gray/Black: 7
TX: Yellow/Black: 10
RX: Orange/Black: 11
(+) Start Output: Gray: 6
(-) Lock Output: Green/Black: 2
10
DBALL/DBALL2
RF
Prog. Button
LED
4
14
12
2
Junction Connector(near BCM, rotated view)
Important!The Hood Pin and Remote Start Safety Override Switch are mandatory security devices, but are NOT supplied with the DBALL.
3086
8587
87a
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety Override Switch
6 ampdiodes
Note: hood pin only required on vehicles not equipped with a factory hood pin
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
(+) 12V: Brown: 7
Warning!
Pins 7 & 8 of the BCM connector should ONLY be connected with DBALL2.
2 22 42
3 23 43
4 24
5 25 45
6 26 46
7 27 47
8 28 48
9 29 49
10 30 50
11 31 51
12 32 52
13 33 53
14 34 54
15 35 55
16 36 56
17 37 57
18 38 58
19 39 59
20 40 60
1 21 41
C2280C (BCM)
44
(+) Parking Lights: Green/Orange or Yellow/Blue, pin 1
MS CAN Low: Violet/Orange, pin 40
(+) Parking Lights: Brown/Yellow, pin 26
MS CAN High:Gray/Orange,
pin 41
(-) Lock: Gray/Yellow, pin 36
Driver DoorTrigger: Green/Violet, pin 45
(+) Accessory: Violet/Green,pin 44
Data RX: Violet/Gray,
pin 34
(-) Unlock 1: pin 26
(+) Ignition: Brown/Yellow,pin 43
Data TX:Yellow/Orange,pin 54
(+) Starter: Blue/White,
pin 1
1
2
C2280G (BCM)
(+) 12V: Red, pin 2
(+) 12V
Fuse 10A
(-) Trunk/HatchRelease:
Brown, pin 49
1 7
2 8
3 9
4 10
5
6
11
12
Power Liftgate Switch(on dash)
(-) Trunk Release Output: Gray/Yellow,pin 4
(-) Trunk/Hatch/Power LiftgateRelease Output: Violet/Brown: 9
Junction Connector(behind glove box)
40
1
2
3
4
5
6
7
9
10
11
12
13
14
15
16
17
18
19
208
33
34
35
36
37
38
39
21
22
23
24
25
26
27
28
29
30
31
32
HS CAN Low:White, pin 40
(DBALL2 ONLY)
HS CAN High:White/Blue, pin 39
(DBALL2 ONLY)
C-MAX & Focus
ORC-MAX(if Equipped)
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
Page 13
Refer to the Vehicle Wiring Reference Chart on next page for more information on specific wiring and connections.
10
DBALL/DBALL2
RF
Prog. Button
LED
4
14
12
2
Connect to VehicleRefer to the wiring reference chart on next page for more information.
Installation Type 4 with T-Harness (THFD1)
The Remote Start Safety Override Switch MUST be in the OFF position.
Remote Start SafetyOverride Switch
4321
4
1
3
2
[1] (-) Unlock 1 Output: Red/Black
(-) Lock Output: Green/Black
RAP Off: Yellow/Red
RAP Off: Orange/Red
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
HS CAN Low: White, pin 14 (DBALL2 ONLY)
OBDII DiagnosticConnector
1 8
169
MS CAN High: Tan/Black
MS CAN Low: Tan
HS CAN Low: Orange/Brown
HS CAN High: Orange/Green
HS CAN High: White/Blue, pin 6, (DBALL2 ONLY)
THFD1 Rev.2(Optional T-Harness)
(+) Parking Light Output: Brown
(+) 12V: Yellow
(+) Parking Light Output: White
2142
223
324
425
526
627
728
829
930
1031
1132
1233
1334
1435
1536
1637
1738
1839
1940
2041
122
C2280A (BCM)
Ignition Barrel
P.A.T.S.(black 4-pin connector)
(vehicle side)(vehicle side) Violet
Attention! DO NOT Cut loop in RSR application.
Warning!
Pins 6 & 14 of the OBDII connector should ONLY be connected with DBALL2.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Ignition Switch(black 7-pin connector)
7421 3 5 6 1 432
2
2
2
2
5
5
5
5
3
3
3
3
6
6
6
6
4
4
4
4
1
1
1
1
7
7
7
7
MS CAN High: Gray/Orange, pin 3
MS CAN Low: Violet/Orange, pin 11
(+) Parking Lights: Green/Orange or Yellow/Blue, pin 1
(+) Parking Lights: Brown/Yellow, pin 26
1
2
C2280G (BCM)
(+) 12V: Red, pin 2
D2Donly
1 7
2 8
3 9
4 10
5
6
11
12
Driver DoorTrigger: Green/Violet, pin 45
22242
32343
42444
52545
62646
72747
82848
92949
103050
113151
123252
133353
143454
153555
163656
173757
183858
193959
204060
12141
C2280B (BCM)
(-) Lock: Gray/Yellow, pin 36
(-) Trunk ReleaseOutput: Brown, pin 49
Power Liftgate Switch(on dash)
(-) Trunk Release Output: Gray/Yellow,pin 4
(-) Trunk Activation Output: Violet/Brown
C-MAX & Focus
ORC-MAX(if Equipped)
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
Type 4 - Vehicle Wiring Reference ChartsPage 14
Function Wire Color Pin Polarity Name, Location on vehicle Color No. Pins
MS CAN High (w/o T-Harness) Gray/Orange 41 Data C2280A conn. At BCM located on passenger side behind glove box. Green 42-pin
MS CAN Low (w/o T-Harness) Violet/Orange 40 Data C2280A conn. At BCM located on passenger side behind glove box. Green 42-pin
MS CAN High (w/ T-Harness) Gray/Orange 3 Data Diagnostic Connector (OBDII) Gray 16-pin
MS CAN Low (w/ T-Harness) Violet/Orange 11 Data Diagnostic Connector (OBDII) Gray 16-pin
Parking LightsYellow/Blue &
Brown/Yellow1 & 26 (+) C2280A conn. At BCM located on passenger side behind glove box. Green 42-pin
Driver Door Trigger Green/Violet 45 (-) N.C. C2280B conn. At BCM located on passenger side behind glove box. Brown 60-pin
Lock Gray/Yellow 36 (-) C2280B conn. At BCM located on passenger side behind glove box. Brown 60-pin
Unlock 2 Black 19 (-) Driver Door Module in driver door Black 22-pin
Accessory Violet/Green 44 (+) C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
Data RX Violet/Gray 4 Data C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
Data TX Yellow/Orange 3 Data C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
HS CAN High (w/o T-Harness) White/Blue 39 Data Junction Connector behind glove box. White 40-pin
HS CAN Low (w/o T-Harness) White 40 Data Junction Connector behind glove box. White 40-pin
HS CAN High (w/ T-Harness) White/Blue 6 Data Diagnostic Connector (OBDII) Gray 16-pin
HS CAN Low (w/ T-Harness) White 14 Data Diagnostic Connector (OBDII) Gray 16-pin
Ignition Brown/Yellow 43 (+) C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
Unlock Violet/Gray 26 (-) C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
12V Red 2 (+) C2280G conn. At BCM located on passenger side behind glove box. Green 2-pin
Starter Blue/White 4 (+) Junction conn. Near BCM located on passenger side behind glove box. Black 27-pin
Power Liftgate (if equipped) Gray/Yellow 4 (-) Power Lift gate, on dash Gray 12-pin
Trunk/Hatch Release Brown 49 (-) C2280B conn. At BCM located on passenger side behind glove box. Brown 60-pin
Wire Information Connector Information
Ford C-Max 2013-2015
Function Wire Color Pin Polarity Name, Location on vehicle Color No. Pins
MS CAN High (w/o T-Harness) Gray/Orange 41 Data C2280A conn. At BCM located on passenger side behind glove box. Green 42-pin
MS CAN Low (w/o T-Harness) Violet/Orange 40 Data C2280A conn. At BCM located on passenger side behind glove box. Green 42-pin
MS CAN High (w/ T-Harness) Gray/Orange 3 Data Diagnostic Connector (OBDII) White 16-pin
MS CAN Low (w/ T-Harness) Violet/Orange 11 Data Diagnostic Connector (OBDII) White 16-pin
Parking LightsYellow/Blue &
Brown/ Yellow1 & 26 (+) C2280A conn. At BCM located on passenger side behind glove box. Green 42-pin
Driver Door Trigger Green/Violet 45 (-) N.C. C2280B conn. At BCM located on passenger side behind glove box. Brown 60-pin
Trunk Release Brown 49 (-) C2280B conn. At BCM located on passenger side behind glove box. Brown 60-pin
Lock Brown 36 (-) C2280B conn. At BCM located on passenger side behind glove box. Brown 60-pin
UnlockViolet or
Brown/Green26 (+) C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
Accessory Violet/Green 44 (+) C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
Data RX Violet/Gray 34 Data C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
Data TX Yellow/Orange 54 Data C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
HS CAN High (w/o T-Harness) White/Blue 39 Data Junction Connector behind glove box. White 40-pin
HS CAN Low (w/o T-Harness) White 40 Data Junction Connector behind glove box. White 40-pin
HS CAN High (w/ T-Harness) White/Blue 6 Data Diagnostic Connector (OBDII) White 16-pin
HS CAN Low (w/ T-Harness) White 14 Data Diagnostic Connector (OBDII) White 16-pin
Ignition Brown/Yellow 43 (+) C2280C conn. At BCM located on passenger side behind glove box. Blue 60-pin
12V Red 2 (+) C2280G conn. At BCM located on passenger side behind glove box. Green 2-pin
Starter Blue/White 4 (+) Junction conn. Near BCM located on passenger side behind glove box. Black 27-pin
Wire Information Connector Information
Ford Focus 2015-2016
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
The optional XL202 and antenna are not included and MUST be purchased separately.
Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.
4
4
XL202
An
ten
na
XOVER
SmartStart is optional and not included. It MUST be purchased separately.
SmartStart is optional and not included. It MUST be purchased separately.
The DBALL Remote Start Ready (RSR) solution offers two (2) configuration options to control your system: RF Kit or SmartStart (both sold separately). This section provides specific installation information for SmartStart and XL202.
Configuration Wires (Gray & White)Connect Gray wire to (-) Ground
5 pins
D2D (4 pins, white)
4 pins
2 pins, not usedCABLE
CABLE
The modules must be connected in a specific order. Refer to the Module Programming section for more information.
1. Use the D2D Crossover (XOVER) cable that is provided with XL202, and NOT the one in the DBALL package.2. The modules must be connected in a specific order. Refer to the Module Programming section for more information.
The modules must be connected in a specific order. Refer to the Module Programming section for more information.
SmartStart/XL202 Installation Notes
SmartStart Revision B
RF Kit
RF Kit & PKE Combination
Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.
RF Kit, PKE & SmartStart BT Combination
SmartStart Revision A
LED
Prog.Button
D2D (4 pins, white)
4 pins
2 pins, not used
OR
SmartStart
Configuration Wires (White & Brown or Blue)Cut Brown or Blue Loop
LED
THIS SIDE UP
LED
Page 15
DBALL/DBALL2
DBALL/DBALL2
DBALL/DBALL2
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
Page 16
Go to the next page to begin the module programming.
Refer to the LED Diagnostics section on page 21 more information and for troubleshooting purposes.
10-pinD2D
XL202
10-pinD2DSmartStart
OR
The DBALL module must be disconnected from any power source before SmartStart can be connected to it. Failing to do so could damage DBALL.
a. To ensure that the D2D communication between SmartStart and DBALL works properly, the Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or Blue loop must be cut (Rev A SmartStart).
b. Do NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by the DBALL D2D connector.
Connect SmartStart to DBALL using the D2D port.
SmartStart Installation
Connect XL202 to DBALL using the D2D port.
XL202 Installation
Module Programming
2Key at IGN
1st Key IN OF
F
START
IGNInsert the first key, turn the key to the IGN position,
the LED flashes green. Wait at least 3 seconds, but no more than 10 seconds, then remove it.
&Flashes
1st Key OUT OF
F
START
IGN
Key out after 3-10 secs
Method 1: 2 Keys required
Module Programming
Refer to the LED Diagnostics section for more information and for troubleshooting purposes.
1 10-pinD2D
st1
12-pin14-pin
nd2
rd3
&Solid
Connect the 10-pin, 12-pin and 14-pin harnesses to DBALL, then wait until the LED turns ON solid red.
ImportantMake all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper feature and function programming is selected using XpressVIP (version 4.5 or higher). Visit www.directechs.com to download the latest version of the application.
Warning! To take advantage of advanced features, you must use XpressVIP 4.5 (and higher) or the Directechs Mobile app.
When the flashing operation is successful, you can proceed with the programming instructions below.
Flashing a module using your computer:
1. Connect the interface module to your computer using the XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and select the Config for RSR button.
3. Follow the instructions to select your vehicle, installation type, and configure your options.
4. Once you have configured the firmware options, click on the FLASH button.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your XKLoader3.
2. Launch the Directechs Mobile app on your smartphone or tablet.
3. Select FLASH YOUR MODULE and follow the on screen instructions.
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
Page 17
3Key at IGN
2nd Key IN OF
F
START
IGNInsert the second key and turn it to the IGN position:
the LED flashes orange. Wait at least 3 seconds but no more than 10 seconds, then remove the key.
within 5 seconds:
You have successfully completed the module programming sequence.
&OffSolid
Press the programming button.
The vehicle ignition will be triggered.
The LED turns ON solid green for 3 seconds, then turns OFF once the module has been successfully programmed.
Press
4
within 5 seconds:
&
2nd Key OUT OF
F
START
IGN
Key out after 3-10 secsFlashes
Module Programming
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
Refer to the LED Diagnostics section on page 21 for more information and for troubleshooting purposes.Version 4.5 or higher of XpressVIP must be installed on your computer to complete this programming sequence.
2Open an Internet Explorer browser (version 6 or higher), and go to www.directechs.com. The detail of the platform and firmware that is currently saved on the interface module will be indicated in the top left corner of the page.
1
3
4
Connect the DBALL/DBALL2 module to your computer using the XKLoader.
Flash your module with the firmware corresponding to FORD4 Key2GO.
Connect the DBALL/DBALL2 wiring to the vehicle first, and only then, plug the harnesses to the DBALL without pressing the programming button. The LED turns ON solid red.
Method 2 : Web programming for Key2Go (using 1 key)
Module ProgrammingPage 18
5
8
7
6
Insert your key into the ignition barrel,
then turn the ignition ON and OFF twice The LED starts flashing orange, indicating that it is ready for the next step.
Once the configuration is completed, reconnect the DBALL/DBALL2 to the vehicle. The LED flashes once orange, and then turns ON solid green for 3 seconds.
Select the method and click on Submit Key2GO Request.
Remove the DBALL/DBALL2 from the vehicle and reconnect it to your computer. The Directechs web site will automatically recognize that you are moving onto the second phase of the programming sequence.
You have successfully completed the module programming sequence.
&+Flashes
Orange
OF
F
START
IGNKey IN O
FF
START2 xO
N
&Solid
Green 3 secs
Flashes
Orange
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
1If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
10-pinD2D
st1
12-pin14-pin
nd2
th4
rd3
2
Solid
&Release
3 Release the programming button. The LED turns ON solid red.
Module Reset
Hard Reset
2 & &
1
Wait 3 seconds until the LED turns ON solid orange then release the programming button. The LED turns ON solid red.
If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
10-pinD2D
st1
12-pin14-pin
nd2
th4
rd3
Solid Release Solid
Solid Flashes
&Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the LED starts to flash orange and red.
Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected.
Page 19
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
Page 20
Feature and Option List
To enter feature programming routine Turn the ignition ON, then OFF. Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the
Programming button. The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate
the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat until a new command is entered.
Changing feature options Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly
the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.
Accessing another feature Press and release the programming button a number of times to advance from the current feature to the next desired feature. The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to
indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.
When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.
Once a feature is programmed Other features can be programmed. The feature programming can be exited.
Exiting feature programming No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming
sequence.OR
Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming sequence.
Feature Programming Programming Button
Feat. Operation Flashes/Options Description
1. No RF Output* Module is connected to a remote starter using a standard installation.
2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).
3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).
1. Disabled
The OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm
command will be executed at the beginning or end of the sequence; it must be controlled by
the Remote Starter.
2. SafelockSmart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It
will unlock at the beginning of the sequence, and relock after start and shutdown.
3. Enabled*
Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm
the vehicle in the remote start sequence, only when required. The reason for this is, factory
alarm control must often be done by lock or unlock operation. This could create unnecessary
actions on door lock modules, such as the horn to honk. When possible, Smart OEM Alarm
Control will monitor the alarm and door lock status to detect if the disarm or rearm is required.
If the vehicle is unlocked or is not equipped with factory alarm, the disarm/rearm will not be
executed. Smart OEM Alarm Control will also monitor the remote starter actions so that the
factory alarm control is not done twice. A remote starter, for which the Safelock feature is active,
will work perfectly with this option and will make it invisible to the user.
* Default Option
2Smart OEM
Alarm Control
1RFTD Output
Type
It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on www.directechs.com. The web offers more options; however, manual configuration of the features is possible using the information on this page.
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
LED Diagnostics and TroubleshootingPage 21
LED Description Troubleshooting
Module has no power.
Make sure the D2D harness is connected or that the
12 Volt is present between the red and black wires. If
the 12 Volt is present, the module may be defective.
Waiting to begin the
programming sequence.
Make sure that all the connections are correct (see
wiring diagram).
Initialisation failed.
If a second attempt fails after a complete Hard Reset,
connect the module to Directechs.com and call Tech
Support with the module ID in hand.
CAN detected and first bypass log
doneNormal operation.
Bypass log is done. Normal operation.
Module was successfully
programmed.Normal operation.
Module was successfully
programmed without bypass.Bypass has been skipped during programing by the user.
CAN2 not detected.Check the CAN2 wire connections. Wake up the data bus
by turning the ignition on and try again.
CAN1 not detected.Check the CAN1 wire connections. Wake up the data bus
by turning the ignition on and try again.
Bypass data not detected.Check the bypass line connection. If more than one wire is
used, make sure they are not inverted.
OBDII feature not supported. Diagnostic data bus not detected.
GROUND OUT ON (GWR) command
received.
Otherwise, the Ground While Running (status) signal was
lost or was never received by the module.
IGNITION ON command received.Otherwise, the ignition signal was not received by the
module.
START ON command received. Otherwise, the start signal was not received by the module.
LOCK command received.
UNLOCK command received.
TRUNK command received.
3x OEM Lock Remote Start Activation
was attempted when RFTD feature is
disabled.
Activated from Web automatically when using RSR flash tool
or can be done manually. Refer to feature programing
section for more information.
RSR Code
If the bypass module fails to flash, the module did not receive
the signal.
Module programming
Active Ground While Running
Module Programming - Error Codes
External Module Synchronisation
D2D and W2W Commands
Off
Solid red
Flashesgreen
Flashes orangeslowly
Solid green3 sec.
Solid orangex 3 sec.
Flashes red x2
Flashes red x3
Flashes red x1
Flashes red, red & orange x 10
Flashes green
Flashes red & orange
Flashes greenquickly
Flashesorange x1
Flashesorange x2
Flashes orange x3
Flashesgreen &red
Flashes red x 7
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
Page 22
Limited One Year Consumer Warranty
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.
This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s website at: www.directed.com
920-10012-01 2013-07
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.
Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.
Rev.: 20160314
© 2016 Directed. All rights reserved.
Platform: DBALL/DBALL2Firmware: FORD4 Remote Start Ready (RSR) Installation
Quick Reference GuideDBALL/DBALL2-FORD4 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
* Your aftermarket remote may differ from the model shown in the illustrations.
Pit Stop ModeVehicle Takeover
4
3
1Press the remote start button on thetransmitter to start the vehicle.*
2
Press he brake pedal, put the car in gear and drive off.
Press the Unlock button on the OEM or aftermarket remote.*
Ready to drive off
1
2
3
Stop the vehicle in a safe parking spot and put the gear in Park (P).
* Your aftermarket remote may differ from the model shown in the illustrations.
Stop & put vehicle in Park (P)
P&
The Pit Stop Mode feature is practical when you need to stop and run an errand, but wish to keep the engine running.
Note: We recommend that you always lock thedoors of your vehicle when leaving it unattended.
It is now safe to leavethe engine running and exit the vehicle.
Press Unlock button on
either remote*OR
PressRemote
Start
PressRemote
Start
Key IN OF
F
START
IGNEnter the vehicle, insert the key into the ignition
barrel and turn it to the ON or IGN position.
Key OUT OF
F
START
IGN
Press the button to remote to start the vehicle.*
Parking Light Error CodesThe parking lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below.
Flashes Diagnostic
1 Runtime expired.
2 Over-rev shutdown.
3 Low/No RPM.
4 Transmitter shutdown.
5 Brake shutdown.
6 Hood shutdown/Remote start safety override switch is ON*.
7 Remote start safety override switch is ON*.
* If the vehicle hood status is supported through data, safety override switch input will report 7 flashes.
Remote Start Ready (RSR)
Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance.
�佒L �� A�
佃 呅剆
G畩摥猠�慮�楳�楳灯湩扬敳甠睷w�摡瑡汩湫�潭
块 偐佒
W��T�����单 T A畴潭潴楶攠D慴愠S潬畴楯湳 I湣����
Hyundai Genesis Sedan with Smart Key
©2010DirectedElectronics.Allrightsreserved.
("Push-button Start")
Hyundai proximity key solution
Quick Reference GuideDBALL/DBALL2-FORD4 Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Button(s) Actions
Press & hold for 1 second to lock.
Press & hold for 1 second to unlock.
Press & hold for 1 second to remote
start.
Press & hold for 5 seconds to activate
the trunk release (optional).
Press once, then to activate the
rear hatch/tail glass release (optional).*
Press 3 times, then to activate
the panic mode.
Press once, then to reset the
remote starter runtime.
List of Available Commands
x1 +
x3 +
x1 +
* This output is configurable. see your authorized installation center for more information.
Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information.
SmartStart Compatible
This system is compatible with Directed SmartStart 3.0. For a complete list of supported features, please visit www.mysmartstart.com.
What is SmartStart?
Now you can remote start, lock and unlock your car just by pushing a button on your smartphone; using the SmartStart App from Directed, the leader in vehicle security and remote start. The simple graphical interface gives you control over the following features of your installed remote start or security with remote start system:
Ÿ Lock/ArmŸ Unlock/DisarmŸ Remote Car StarterŸ Trunk ReleaseŸ PanicŸ Aux Channels
You can also control multiple vehicles – great for families – and assign more than one user to control a vehicle. It's easy with SmartStart!
But, this is only the beginning! SmartStart is loaded with additional features including GPS tracking, SmartSchedule, vehicle status, roadside assistance, home control, parked car finder and more.
3.0 enables a "Cloud-Connected Car" like never before, providing an entirely new level of 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.
For more information, visit www.mysmartstart.com.
Notes
�佒L �� A�
佃 呅剆
G畩摥猠�慮�楳�楳灯湩扬敳甠睷w�摡瑡汩湫�潭
块 偐佒
W��T�����单 T A畴潭潴楶攠D慴愠S潬畴楯湳 I湣����
Hyundai Genesis Sedan with Smart Key
©2010DirectedElectronics.Allrightsreserved.
("Push-button Start")
Hyundai proximity key solution