data sheet single and dual input analyzers ss/ax4ph issue 7 for...

Data SheetSS/AX4PH Issue 7

Single and Dual Input Analyzersfor pH/Redox (ORP)

AX460, AX466 and AX416

Cost effective

– select one or two pH/Redox (ORP) inputs or combine pH/Redox (ORP) and conductivity in one analyzer

Reduced installation cost

– easy access terminations; reduced panel space

High functionality at minimum cost

– three alarms and two fully isolated current outputs

– integral Water/Chemical sensor cleaner control

– integral PID controller (AX460)

Expanded monitoring and control

– add-on option board provides a total of five alarm relays and four current outputs

– service log-book providing historical data

On line assurance of reliability

– comprehensive sensor and instrument self-checking

Energy saving

– high visibility backlit display with auto switch-off function

Reduced yearly maintenance costs

– 12 to 30V DC option negates the need for costly safety tests

Wide range of applicability

– water and wastewater treatment– power, pure water– semiconductors– chemicals– pharmaceuticals– pulp & paper

More processing power, higherperformance

Single and Dual Input Analyzers for pH/Redox (ORP)AX460, AX466 and AX416 SS/AX4PH Issue 7

2

The AX400 SeriesAX400 analyzers incorporate the latest technology to providehighly reliable, flexible, feature-packed devices that satisfy adiverse range of process monitoring and control applications.The complete range encompasses solutions for pH/Redox(ORP), conductivity and dissolved oxygen.

AX46x analyzers enable continuous measurements of one ortwo pH or Redox (ORP) points with simultaneous local displayand retransmission. AX46x is used with glass, enamel andantimony pH electrodes and metal Redox sensors, providingmeasurements with exceptional accuracy and performance.

AX400 Series analyzers are available for either wall-/pipe- orpanel-mounting and are rated to IP66/NEMA 4X.

High Functionality as StandardAll versions are supplied with two, fully isolated current outputsas standard, that can be assigned to the measured parameter,sample temperature or any appropriate calculated variables.

Three programmable relay set points are available that can alsobe assigned as required.

Innovative features such as power-saving display and adiagnostic current output option all contribute to a low cost ofownership.

Plug-and-Produce Expanded ControlAn advanced function card provides an additional two currentoutputs and two further alarm relays that can be assigned toeither measured values or sample temperature.

ABB Plug-and-Produce software automatically reconfigures theanalyzer if an option board is added later. No user programmingis necessary.

A real-time clock and logbook are also included making thefull-facility versions extremely powerful and versatile.

Significantly Reduced Maintenance CostsThe AX400 analyzers are supplied as standard for 85 to 265VAC operation. There are no inner switches to set.

They can also be provided for 24V AC or 12 to 30V DC supplyand recognize automatically which of the two supplies is beingused. 24V DC operation reduces maintenance costssignificantly by negating the need for costly, yearly safety tests toensure compliance with safety procedures.

Energy Saving DisplayThe backlit display has been designed to operate in all types ofenvironments and shows both the measured parameter(s) and,on a separate 16-character display line, diagnostic andcomputed information.

On dual-input analyzers both measured parameters aredisplayed simultaneously.

For conservation of energy, the backlight can be set to switch offautomatically after 60s of inactivity.

Easy-Access Installation TerminalsEasy access to the terminations ensures rapid andcost-effective installation. The wall-/pipe-mount version hasbeen designed to ensure that cable connection is simple andconvenient. Ingress protection of the electronics section isretained even when the terminal compartment cover is opened.

AX400 Outputs

Backlight Can Be Set to Switch-off When Inactive

AX400 Termination Chamber Makes Access Easy


3

Dual Input Measurement for Critical DutiesThe AX400 enables two continuous measurements withsimultaneous local display and retransmission. This capabilityprovides an on-line validation of the process measurement.

Making two simultaneous measurements and configuring one ofthe set points as a difference alarm provides continuous on-linechecking and early warning of an invalid measurement.

Detecting breakthrough of ammonia in a chiller unit is madepossible with dual measurement. Comparison before and afterthe chiller ensures extremely rapid leakage detection, preventingdamage to the system.

Waste Treatment pH & Redox (ORP)pH and Redox (ORP) are essential control parameters whenremoving toxic chromium ions from waste water inmetal-finishing applications. Dual pH and Redox analyzers andintegral control simplifies installation and reduces investmentcosts.

Just-in-Time MaintenanceOne of the most vulnerable times for a pH electrode is duringreintroduction into the line. If used with a solution earth rod,AX46x analyzers with advanced diagnostic facilities can detectsensor breakages as they occur. In addition, they can detectsensors out-of-process and several reference faults for faultdiagnosis and reduced downtime.

Dual-input Comparator for Critical Measurements

Ammonia Leakage Detection in a Chiller Unit

!!"#$

%%

&'()*+

%%"

Waste Treatment pH and Redox (ORP)

Just-in-Time Maintenance

*%

,

, !!,

*

!-

.$

/'0,/

/100/

/( /

/2/


4

Reduced Maintenance Through In-line CleaningMany installed pH sensors benefit from regular cleaning. Whencarried out manually, this can be laborious and costly – so isoften ignored. Advanced AX400 pH analyzers make it possibleto automate sensor cleaning by using a programmablewash-timer contact to activate a cleaning agent valve or pump.

Pulsed water-wash and jet-wash chemical clean actions arestandard, user-selectable functions. The frequency and durationof the wash can be tuned to meet the requirements of theapplication.

For chemical cleaning a 60 liter (13 gallon) sensor cleaningstation can be supplied (model no. AA0010), complete withdelivery pump and low level alarm. Chemical cleaning hasproved particularly successful on potable drinking water plantswhere manganese and iron in the sample can createunacceptably high levels of maintenance. Effective cleaningreduces cost of ownership.

Combined Conductivity and pHThe AX416 version measures conductivity and pH with thesame analyzer. The option board provides the capability toretransmit pH, conductivity and both sample temperatures. Fiveprogrammable alarms can be assigned to suit the needs of theapplication, enabling even the most demanding requirements tobe met.

AX460 Integral P, PI and PID ControlThe single input AX460 analyzers incorporate three-term PIDControl, offering three modes of sophisticated control: analog,pulse length (time proportional) and pulse frequency. These aresupplied as standard and can be operated in direct- orreverse-acting mode, dependent upon the application.

Auto/Manual and Bumpless TransferAn auto/manual feature is incorporated for rapid manual accessto the control functions. The controller facilitates bumplesstransfer between manual and auto modes, providing themeasured variable is within the proportional band and someintegral action time has been programmed.

Current Output Proportional ControlIn this case, the control signal is provided by the 4 to 20mAoutput of the AX460 analyzers rather than using thealarm/control contacts. The magnitude of the current outputchanges in proportion to the deviation from set point. Thismethod is used generally with motorized valves or whencontrolling the speed of dosing pumps with a 4 to 20mAproportional input.

Efficient Auto-cleaning Control for One or Two Sensor Systems

Simultaneous Conductivity and pH Measurement

3

--+

++&'

'

!)$,%*

AX460 – Integral P, PI, and PID Control

Current Acting Control

+

+04'

(

3

!-$

+&0

&

-

56


5

Time Proportioning Control (Pulse Length)With time proportioning control, the AX460 analyzerÕs controlsignal output is in pulses, the duration of which changes inproportion to the system error. The pulses are delivered byvarying the length of time that the alarm/control contact isactivated.

Time Proportioning Control is used generally to control dosingby low-cost solenoid valves or metering pumps and is alsoknown as pulse-length proportional or Mark Space control.

Bi-directional ControlAs well as single set point control for both acid and baseaddition, the AX460 analyzer can be configured withindependent controllers.

To avoid control overlap, a minimum of 0.5pH difference (ordeadband) between the set points is essential. The differencebetween the set points varies depending upon the application.

Control of each set point can be configured independently aseither P or PI control in this mode. The setting of proportionalband or integral action can also be different for each set point.

Pulse-frequency Proportional ControlImpulse pumps dosing chemical reagents are controlled easilyby the AX460 analyzerÕs pulse-frequency proportional controloutput. In this case, the pulse length of the alarm/controlcontact is fixed and the frequency of the delivered pulsesincreases in proportion to the system error, as set by theproportional band. Diaphragm metering pumps must have aremote pulse input capability in order to utilize this function.

Pulse-frequency control in the AX460 analyzer operates bypulsing a relay on for 300ms and off for a period of timedetermined by the pulse frequency. The pulse frequency (PFr) isadjustable between 1 and 120 pulses per minute. The greaterthe difference between the measured variable and the set pointthe greater the pulse frequency.

Example

If the pulse frequency is set at 120 pulses per minute and thepercentage output is 100% then the pulse rate is 2 pulses persecond. If the percentage output is reduced to 50%, the pulserate falls to one pulse per second.

Power Failure RecoveryIn the event of a power failure the user can configure the controlmode to be Auto, Manual or Last. This optimizes controlconditions on power-up to ensure rapid recovery of processcontrol.

Time Proportioning Control

Bi-directional Control

78-9

7:89

;+$

(+$

;+$<8

:<8

88

:<8

7-

7-9

(+$

;+$

(+$

;+$

<8

789

-9

--9

-

=3

+*

Pulse-frequency Proportional Control

7-9

78-9

7--9

(+$

;+$

(+$

;+$

;+$

2>7-

-< -<:

-< -< -< -<


6

Specification

pH/Redox (ORP) – AX460 and AX466Inputs

One or two* pH or mV inputs and solution earth

One or two* temperature sensors

Enables connection to glass or enamel pH and reference sensors andRedox (ORP) sensors

*AX466 only

Input resistanceGlass >1 x 1013Ω

Reference 1 x 1013Ω

Range–2 to 16pH or –1200 to +1200mV

Minimum spanAny 2pH span or 100mV

Resolution0.01pH

Accuracy0.01pH

Temperature compensation modesAutomatic or manual Nernstian compensation

Range –10 to 200°C (14 to 392°F)

Process solution compensation with configurable coefficient

Range –10 to 200°C (14 to 392°F)

adjustable –0.05 to +0.02%/°C (–0.02 to +0.009%/°F)

Temperature sensorProgrammable Pt100, Pt1000 or Balco 3kΩ

Calibration RangesCheck value (zero point)

0 to 14pH

SlopeBetween 40 and 105% (low limit user-configurable)

Electrode Calibration ModesCalibration with auto-stability checking

Automatic 1 or 2 point calibration selectable from:

ABB

DIN

Merck

NIST

US Tech

2 x user-defined buffer tables for manual entry,

2-point calibration or single-point process calibration

Conductivity – AX416 OnlyRange

Programmable 0 to 0.5 to 0 to 10,000µS/cm (with various cell constants)

Minimum span10 x cell constant

Maximum span10,000 x cell constant

Units of measureµS/cm, µS/m, mS/cm, mS/m, MΩ-cm and TDS

AccuracyBetter than ±0.01% of span (0 to 100µS/cm)

Better than ±1% of reading (10,1000µS/cm)

Operating temperature range–10 to 200°C (14 to 392°F)

Temperature compensation–10 to 200°C (14 to 392°F)

Temperature coefficientProgrammable 0 to 5%/°C and fixed temperature compensationcurves (programmable) for acids, neutral salts and ammonia

Temperature sensorProgrammable Pt100 or Pt1000

Reference Temperature25°C (77°F)

DisplayType

Dual 5-digit, 7-segment backlit LCD

Information16-character, single line dot-matrix

Energy-saving functionBacklit LCD configurable as ON or Auto-Off after 60s

Logbook*Electronic record of major process events and calibration data

Real-time clock*Records time for logbook and auto-manual functions

*Available if option board is fitted


7

Relay Outputs – On/OffNumber of relays

Three supplied as standard or five with option board fitted

Number of set pointsThree supplied as standard or five with option board fitted

Set point adjustmentConfigurable as normal or failsafe high/low or diagnostic alert

Hysteresis of readingProgrammable 0 to 5% in 0.1% increments

DelayProgrammable 0 to 60s in 1s intervals

Relay contactsSingle-pole changeover

Rating 5A, 115/230V AC, 5A DC

Insulation2kV RMS contacts to earth/ground

Analog Outputs Number of current outputs (fully isolated)

Two supplied as standard or four with option board fitted

Output ranges0 to 10mA, 0 to 20mA or 4 to 20mA

Analog output programmable to any value between 0 and 22mA toindicate system failure

Accuracy±0.25% FSD, ±0.5% of reading (whichever is the greater)

Resolution0.1% at 10mA, 0.05% at 20mA

Maximum load resistance750Ω at 20mA

ConfigurationCan be assigned to either measured variable or either sampletemperature

Digital CommunicationsCommunications

Profibus DP (with option board fitted)

Control Function – AX460 OnlyController Type

P, PI, PID (configurable)

Control OutputsOutput

Can be assigned a maximum of two relays, two analog outputs, orone of each

AnalogCurrent output control (0 to 100%)

Time proportioning cycle time1.0 to 300.0s, programmable in increments of 0.1s

Pulse frequency1 to 120 pulses per minute, programmable in increments of 1 pulseper minute

Controller actionReverse, direct or bi-directional (programmable)

Proportional band0.1 to 999.9%, programmable in increments of 0.1%

Integral action time (Integral reset)1 to 7200s, programmable in increments of 1s (0 = Off)

Derivative0.1 to 999.9s programmable in increments of 0.1s, available only forsingle set point control

Auto/ManualUser-programmable

Access to FunctionsDirect keypad access

Measurement, maintenance, configuration, diagnostics and servicefunctions

Performed without external equipment or internal jumpers

Sensor Cleaning FunctionConfigurable cleaning action relay contact

Continuous

Pulse in 1s on and off times

Frequency5 minutes to 24 hours, programmable in 15 minute increments up to1 hour then in 1 hour increments for 1 to 24 hours

Duration15s to 10 minutes, programmable in 15s increments up to 1 minutethen in 1 minute increments up to 10 minutes

Recovery period30s to 5 minutes, programmable in 30s increments


8

Mechanical DataWall-/Pipe-mount versions

IP66/NEMA4X

Dimensions 192mm high x 230mm wide x 94mm deep(7.56 in. high x 9.06 in. wide x 3.7 in. deep)

Weight 1kg (2.2 lb)

Panel-mount versionsIP66/NEMA4X (front only)

Dimensions 96mm x 96mm x 162mm deep(3.78 in. x 3.78 in. x 6.38 in. deep)

Weight 0.6kg (1.32 lb)

Cable Entry Types

Power SupplyVoltage requirements

85 to 265V AC 50/60 Hz

24V AC or 12 to 30V DC (optional)

Power consumption<10VA

InsulationMains to earth (line to ground) 2kV RMS

Environmental DataOperating temperature limits

–20 to 65°C (–4 to 149°F)

Storage temperature limits–25 to 75°C (–13 to 167°F)

Operating humidity limits Up to 95%RH non condensing

EMCEmissions and immunity

Meets requirements of:

EN61326 (for an industrial environment)

EN50081-2

EN50082-2

Hazardous area approvals

SafetyGeneral safety

EN61010-1

Overvoltage Class II on inputs and outputs

Pollution category 2

LanguagesLanguages configurable:

English

French

German

Italian

Spanish

Standard 5 or 7 x M20 cable glands

North American 7 x knockouts suitable for 1/2 in. Hubble gland

CENELEC ATEX IIG EEx n IIC T4 Pending

FM non-incendive Class I Div. 2 Groups A to D Pending

CSA non-incendive Class I Div. 2 Groups A to D Pending


9

Overall Dimensions

Dimensions in mm (in.)

Wall-/Pipe-mount Version

856

-5?<:6@5:<8!6

@!5<:?6-5-< 6

A!<8-

5-<!6

5-<@6

856

!:<85<!!6 !:<85<!!6

85<::6 85<::6

<85-<??6

<85-<??6

@ 5<:6

:85!<@6

8-58<@6

@5:<8!6

Pipe-mount Detail

!5,?<6 $


Panel-mount Version

@<!- 5<!-6

:<8- 58< 6 8 56 @!5<::6

@!5<::6

8< -5-<6

@<!- 5<!-6


10

Electrical Connections

&05+ 6

&0

&0

&*=

&

5''36

= =B

. .

( (*

8 .

! .

:

? .

@ .

-

.

.

# +

C

8 # +

! C

8

!

:

?

@

-

8

!

.

.

'D

'D

8 '(*

! .

:

? .

@ .

-

. 8

.

# +

C

8 # +

! C

&0 &0

&05+ 6

(*516

Terminal Block B pH/Redox (ORP) without Solution Earth‡

pH/Redox (ORP) with Solution Earth‡

ConductivitySensor B Sensor A

1 9Temperature Compensator common*

Link 1 & 2 / 9 & 10**Temperature Compensator common*

Link 1 & 2 / 9 & 10**Temperature Compensator common

Link 1 & 2 / 9 & 10**

2 10 Temperature Compensator third lead* Temperature Compensator third lead* Temperature Compensator third lead

3 11 Temperature Compensator* Temperature Compensator* Temperature Compensator

4 12 Not applicable Reference Electrode Screen

5 13 Not used Not used Cell (Cell Electrode)

6 14 Reference Electrode Solution Earth‡ Cell (Earth Electrode)

7 15 Screen* Screen* Not used

8 16 Glass/Metal Electrode Glass/Metal Electrode Not used

*If fitted. **When a 2-wire Pt100, Pt1000 or BALCO temperature compensator is fitted.‡Solution Earth also referred to as Ground Rod.


11

Ordering Information

Single and Dual Input Analyzers for pH/Redox (ORP) and ConductivityModels AX460, AX466 & AX416

AX4 X X X X X 0 X

First Process Variable (PV1)

Conductivity 0 to 10,000µS cm–1 for 2-electrode sensorsConductivity 0 to 1,999mS cm–1 for 4 electrode sensorsConductivity USP<645> for 2-electrode sensorspH/Redox (ORP)Dissolved Oxygen

13568

Second Process Variable (PV2)*

No second process variable – select for PID control of PV1Conductivity 0 to 10,000µS cm–1 for 2-electrode sensorsConductivity 0 to 1,999mS cm–1 for 4-electrode sensors**Conductivity USP<645> for 2-electrode sensorspH/Redox (ORP)Dissolved Oxygen

013568

Enclosure Types

Wall-mount IP66/NEMA 4X, General

Wall-mount – cable glands fittedPipe-mount

12

Wall-mount NEMA 4X/IP66, North American

Wall-mountPipe-mount

67

Panel-mount, Universal

Panel-mount** 5

Advanced Functions & Communications

Basic (2 current outputs + 3 relays)Advanced (4 current outputs + 5 relays + logbook)Profibus DP, basic (2 current outputs + 3 relays)**Profibus DP, advanced (4 current outputs + 5 relays + logbook)**

0123

Power Supply

85 to 265V AC 45 to 65Hz24V AC/12 to 30V DC (auto-selection)85 to 265V AC 45 to 65Hz (tropicalized)‡24V AC/12 to 30V DC (auto-selection, tropicalized)‡

0123

Reserved 0

Manual

EnglishFrenchItalianGermanSpanish

12345

* When ordering units with a second process variable (PV2) the code digit for PV2 in the order code number must be equal to, or greater than, the code digit for PV1, e.g. AX416 permissible, AX461 not permissible.

** Profibus DP not available in panel-mount housing when 0 to 1,999mS/cm is selected as Second Process Variable (PV2).

‡ Check factory for availability of tropicalization.

SS

/AX4

PH

Issu

e 7

Single and Dual Input Analyzers for pH/Redox (ORP)AX460, AX466 and AX416

ABB has Sales & Customer Support expertisein over 100 countries worldwide

www.abb.com

The Company’s policy is one of continuous product improvement and the right is reserved to modify the

information contained herein without notice.

Printed in UK (05.07)

© ABB 2007

ABB LimitedOldends Lane, StonehouseGloucestershireGL10 3TAUKTel: +44 (0)1453 826661Fax: +44 (0)1453 829671

ABB Inc.Analytical Instruments9716 S. Virginia St., Ste. EReno, Nevada 89521USATel: +1 775 850 4800Fax: +1 775 850 4808

pH/Redox (ORP) Sensors forProcess Monitoring

TB(X)5 Series

Next Step™ Solid State reference– eliminates poisoning, pumping and plugging

Advantage™ Series with solution ground rod– permits continuous sensor diagnostics

Comprehensive selection of measuringelectrodes– sensors designed to suit all application

requirements

Combination style construction– measuring, reference and temperature elements, all

in one compact body

Insertion, submersion, flow-throughand hot-tap– increases flexibility of installation

Integral potted cable– no in-process high impedance connections

Comprehensive selection of wetted materials– assures compatibility with design, budget and

process

Operating temperatures up to 140C (284F)– the highest glass temperature limit on the market

Operating pressures up to 21 bar (300 psi)and higher– the highest pressure limit on the market

The Most Durable pH/Redox (ORP)Sensors in the World

Data SheetSS/TBX5_3

pH/Redox (ORP) Sensors for Process MonitoringTB(X)5 Series SS/TBX5_3

2

The Most Durable pH/Redox (ORP) Sensorsin the WorldA well deserved reputation for ruggedness, longevity andaccuracy hallmark the TB(X)5 Series pH/Redox sensors. Thesensors are easily applied to most industrial measurementneeds. They are renowned for their ability to outperformconventional sensors in the industries’ toughest processapplications.

Solid-state Next Step™ reference technology is the foundationfor all TB(X)5 Series electrodes. The totally solid inner referencechamber is charged with potassium chloride (KCl). This non-liquid reference all but eliminates poisoning, plugging andpumping problems that plague conventional liquid, slurry andgel designs.

The Next Step Advantage™ series incorporates a solutionground rod that enables sensor diagnostics.

All measurement functions are combined in one compact body:reference, measuring electrode, temperature sensor and groundrod. Using an integral potted cable, a completely sealedassembly is provided without in-process high impedanceconnections.

These advances in reference design, combined with superiorglass electrode technology, result in an industrial sensor withunequalled durability and flexibility.

Electrode

Next Step Reference Electrode

Competing Gel orSlurry-filled Reference

Slurry orGel-filledReservoir

Ceramic orTeflon Junction

OptionalSecond Junction

Ag/AgClElement

Next StepSolid StateReference(Not Shown)

TemperatureCompensator

Ag/AgClElement

MetallicSupport Rodand Ground

Wood and TeflonLiquid Junction

Solution GroundInterface

edoC epyT noitpircseD

sgnitaR

egnaRserutarepmeTgnitarepO taecnadepmI

52 77(C )FC F

1 ssalgtalF .gniluofyvaehhtiwytudytisnedhgiHaNwoL.noitcnujdiuqilhtiwhsulfedortcelE + .rorre Hp41ot0 001ot01 212ot06 1 M056

2 esopruplareneGssalg

erutarepmetrewoldnaytudmuidemotthgilroF.HphgihroftoN.snoitacilppa Hp21ot0 001ot0 212ot23 M002

5 )PRO(xodeR .tnemele)tP(munitalP ot0 Vm0002 041ot0 482ot23 k1 6 )bS(ynomitnA .sessecorpFHroevisarbarofedortceleHplateM Hp11ot3 08ot02– 671ot4– k1

F dicA/ediroulF dnaFHtnecreplarevesotpuybgnihcteottnatsiseR.sdicagnorts Hp21ot0 08ot01 2 671ot05 2 M005

J tnatsisergnitaoCerutarepmethgiH

gnorts,HpwoldnahgihrofelbatiusdnaelitasreV.retawytiruphgihdnaslacimehc Hp41ot0 041ot01 482ot05 M005

setoN . 121ot0)1 052ot23(C selcycnoitaziliretsrof)F05)2 221(C noitartnecnocFHhgihrofdednemmocer.xam)F

Wide Variety of Sensorsfor Most Industrial ApplicationsABB offers a wide variety of standard sensors for mostapplications. These include variations in body style, measuringelectrode type and shape, temperature compensator, junctiontype and shape and cable. Next Step Advantage™ sensors alsoallow choice of solution ground and O-ring materials.

Durable ElectrodesThe TB(X)5 electrode design eliminates failures due to thermalstress caused by rapid temperature excursions. Unlike othersensors that use a large inner air bubble for expansionabsorption, TB(X)5 electrodes use a unique inner plunger;providing more effective protection against temperaturefluctuations.

The glass manufacturing process uses inoffensive components.The glass contains no barium, cobalt or uranium oxides. Theimpedance is low enough to maintain signal integrity, yet highenough to remain chemically durable with little or no sodium ion(Na+) error.

The electrodes are available in several measuring element typesensuring greatest process optimization.

Sensor Construction

Electrode Types and Ratings


3

Body StyleSensor bodies are constructed of Kynar (PVDF) or Ryton (PPS).TB5 Series sensors use Solid-State Next Step™ references. TheTB(X)5 Series denotes Next Step Advantage™ types withintegral solution ground.

Sensor Models and Applications

Reference Junction StylesTo promote TB(X)5 electrode process efficiency, referencejunctions are available as either wood or PTFE, each also offeredin flush, notched, or recessed forms.

The hardwood junction is recommended for all general purposeduties particularly those requiring high resistance to coating.PTFE junctions are promoted for continuous processes over11.0 pH or those containing known wood delignifiers such asstrong caustics, bleaches and other oxidizers.

Flush junctions have no process protrusions and thereforesupply excellent self-cleaning properties when used with flatglass and fitted at 90 in process pipelines.

Notched junctions provide an integral protection guard fornormal bulb-style glasses and are especially suited forretractable and immersion sensors.

Recessed junctions are also available. They place the glass bulbbehind a 'hood' giving it protection from abrasive or high velocityprocesses.

Consult factory for availability of recessed junctions.

NormalGlass

FlatGlass

Flush Notched

rebmuNledoMydoB noitacilppAetats-diloS

petStxeN petStxeNegatnavdA

155BT 155XBT SPP,kcol-tsiwT,enil-nI

noisrembuS

655BT 655XBT FDVP,dedaerhT,enil-nI

noisrembuS

755BT 755XBT FDVP pat-toH,rotcarterevlavllaB

165BT 165XBT FDVP elbaziliretS,enil-nI

265BT 265XBT FDVP elbaziliretS,yratinaS

465BT 465XBT FDVP,rotcartererusserphgiH

pat-toH

765BT 765XBT SPP erusserphgiH,enil-nI

Type 1 – Flat Glass

pH

Type 5 – Platinum

ORP

Type 6 – Antimony

pH

pH

Type 2 – General Purpose GlassType F – Fluoride/Acid Resistant GlassType J – Coating Resistant Glass

Electrodes Types

Junction Styles

Junction Styles

)X(BTrosneShsulF dehctoN

dooW EFTP sedortcelE dooW EFTP sedortcelE155 J,F,6,5,2,1

655 6,1 J,F,5,2,1755 6,1 J,F,5,2,1165 J,F,5,1 J,F,5,1265 J,F,5,2,1

465 6 J,F,5,2765 J,F,6,5,2

etoN . noitcelesdilaV= noitcelesdilavnI=

elytS noitpircseD noitacilppA

hsulF rosnesfodnehtiwhsulF sessecorpgniluofyvaeh,enil-nI

dehctoN noitcetorpedortcelegnidivorpnoitcnujdnoyebsdnetxE srosnesnoisremmidna)evlav-llab(pat-toH

Reference Junction Selection


4

Temperature CompensationTemperature compensators enable analyzers to adjust fortemperature effects on the glass pH electrode output (Nernst).Selected analyzers can also use this measurement tocompensate for solution pH temperature effects.

Sensors can be ordered with integral temperature sensors or asexternal units.

The integral temperature compensator is available in two forms;Balco 3k and Pt100.

Integral Temperature Compensator

0.4

pHError

0.3

0.20.1

0.0- 0.1

- 0.2

- 0.3

- 0.4

0-5

-10

-15

+ 5

+ 10

+ 15

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

TemperatureChange (C)From 25 C

Temperature CompensatorLocation (Typical)

ToJunction

Box

Black

Junction BoxWiring

(4TB5023-0088)

Pin Leads(Type 'T' cable)

Female BNC and SpadeLugs for Junction Box

Male BNC / Spade Lug to Pin Leads Extension(Cable 4TB 3011-8XXX)

RedWhiteGreenHeavy Green

WithTemperatureCompensator

(Type '0' Cable)

To TB82,TB84, 4630and AX46

Heavy Green

Pin Leads(Type 'T' cable)

Female BNC and SpadeLugs for Junction Box

Male BNC / Spade Lug to Pin Leads Extension(Cable 4TB 3011-7XXX)

ToJunction

Box

Junction BoxWiring

(4TB5023-0088)

Black

Green

WithoutTemperature

Compensator

(Type '0' Cable)

To TB82,TB84, 4630and AX46

pH Error without Temperature Compensation

Cable OptionsTB(X)5 sensors offer complete flexibility of cabling optionsthroughout the range. All cables are potted inside the sensorensuring environmental protection.

The standard cable length for most sensors is 1.5m(5 ft.). However, cables can be supplied as any continuous sizeup to 9m (30 ft.).

Standard accessories include junction boxes and submersion(immersion) couplers, typically used with extension cables fordirect connection to ABB-TBI instruments.

Extension cables also permit distances between sensor andinstrument of up to 30m (100 ft.) without external preamplifier.

A BNC/TC to pin terminal adapter is available for connection toTB82, TB84, 4630 and AX46 Series instruments.

Sensors with pin terminals are selected with code option ‘T’.Next Step Advantage Sensor Cablesand Junction Box Wiring (TBX5 Models)


5

Note.Junction box supplied without cable glands 4TB9515-0165for use with conduit.

Junction Box Wiring(4TB5023-0162)

Pin LeadsType 'T' cable

Junction Box Wiring(4TB5023-0162)

Male BNCType 'F'cable

Pin LeadsType 'T'cable

Pin Lead Extensionwith Temperature Compensator Connector

(Cable 4TB3011-4XXX)

to TB515, TB540,TBN580 andTB7

Male BNC –Female BNC –to Sensor or

Junction Box

Extension Cable(Cable 4TB3011-1XXX)

Female BNC –To Sensor orJunction Box

Pin LeadsTo TB82, TB84,4630 and AX46

Pin Extension Cable(Cable 4TB3011-3XXX)

To TB515,TB540,TBN580and TB7

To Sensor orJunction Box

To Sensor orJunction Box

Pin LeadsTo TB82, TB84,4630 and AX46

WithoutTemperatureCompensator

WithTemperatureCompensator

Male BNC and TinnedTemperature Compensator Leads

Type 'F' cable

Male BNC and ExtensionCable Connector on

Temperature Compensator LeadsType 'F' cable

Female BNC to Male BNC Extensionwith Temperature Compensator

Connector to Tinned Leads(Cable 4TB 3011-2XXX)

Solid State and Next Step Reference Sensor Cables and Junction Box Wiring (TB5 Models)


6

Models TB551 & TBX551 Ryton SensorsModels TB(X)551 sensors are in-line flow-through orsubmersible (immersion), general purpose, twist-lock stylesensors. The sensor body is molded from chemically resistantRyton (PPS).

The sensor can be adapted to 1 in. fittings by either a threadedRyton receptacle or a twist-lock receptacle. The twist-lockreceptacle is available in Kynar (PVDF) or stainless steel.

Optional electrode guards protect the electrode in submersion(immersion) applications.

Specification

Applications

In-line, flow-through, submersible (immersion)

Max. pressure/temperature

690kPa (100 psi) at 140C (284F)

Features

Low cost, universal type.

Adapter for twist-lock, or threaded-cap, insertion

Material

Body Ryton (Polyphenylene Sulphide)

Junction Wood or Teflon (PTFE)

Junction types Flush


Models TB(X)551 Ryton Sensors

Overall Dimensions – Models TB(X)551

33.0(1.30)

Sensor

Ryton Body

167(6.57)

120.0(4.73)

2.5(0.10)64.5(2.54)

24.4 (0.96)

26.7 (1.05)

Sensor with Junction Box

95.0(3.74)

Electrode

3/4 in. NPT

64.5(2.54)

12 (0.47)

No. 118 Viton O-Rings2 Each

1 in. NPT Tee(CustomerSupplied)

Ryton ThreadedReceptacle

Flow

Safety CatchAssembly

Flex Conduit and Coupling (Customer Supplied)

Open toAllow Airto Escape

ScrewsTurn intoO-RingGroove

316 Stainless SteelSubmersible Guard

PVCSubmersible

Guard

Twist LockReceptacle

316 Stainless SteelKynar

167 (6,57) 71.1(2.80)

3/4 in. NPT

276.9 (10.90)

3/4 in. NPT Conduit Port (2 Typ.)


7

Ordering Information – Models TB(X)551

Notes.1) For direct connection to TB82, TB84, 4630/35 and AX46 transmitters or other supplier devices, using terminal blocks.

2) Not available for Platinum, Redox (ORP), or Antimony, pH, electrodes (codes 5 & 6).

3) Not available for fluoride-resistant electrodes (code F). Compatible with TB82, TB84, 4630/35 and AX46 instruments.

4) Kalrez O-rings only for solution ground sleeve. External O-rings are Viton. External Kalrez O-ring kits available separately.

5) TB551 only. There are 2 options to connect to TB82 or TB84 transmitters:

Option 1 – use BNC/TC to PIN adapter with conduit fitting or BNC/TC to PIN adapter. In either case temperature compensator code must be 2 or 4.

Option 2 – select T in integral cable code, not designed for use with extension cables or junction box.

6) TB551: junction box mounted on sensor. Cable length approx. 102mm (4 in.). Requires extension cable.

7) TB(X)551: when selecting JB or JS, cable length is approx. 102mm (4 in.). Requires extension cable. If junction box is ordered separately and longer cable lengthsare required, enter length under code for integral cable.

srosneSetats-diloSdradnatSdoRdnuorGnoituloSoN petStxeN )elbisrembus(noisremmI,kcol-tsiwT,enil-nI

041@isp001(ylbmessArosneSPRO/HpydoBnotyR )C155BT X X X X X X X X

edortcelEgnirusaeM

1256FJ

001ot01(ssalgtalF 09tawolfhtiwsetalucitraphgihrof)Hp41ot0,C 001ot0(Hp,ssalG )Hp21ot0,C

)PRO(xodeR,munitalP08ot02–(Hp,ynomitnA )Hp11ot3,C

08ot01(tnatsiser-ediroulF,Hp,ssalG )Hp21ot0,C041ot5(erutarepmethgih/ssalgtnatsiser-taoC )Hp41ot0,C

1256FJ

noitasnepmocomrehTlargetnI

01–3–

155XBTroftoN

155XBTroftoN

enoNk3 sdaeldenniT 2

k3 rotcennocelbacnoisnetxE 2

sdaeldenniT001tP 3,2

rotcennocelbacnoisnetxE001tP 3,2

01234

noitcnuJdiuqiL

AB

petStxeN,hsulf,dooWpetStxeN,hsulf,nolfeT

AB

lairetaMdoRdnuorGnoituloS

123

leetssselniats613muinatiT

2ByolletsaH

155BTroftoN155BTroftoN155BTroftoN

lairetaMgniR-O

1234

notiVMDPE

enociliSzerlaK 4

155BTroftoN155BTroftoN155BTroftoN155BTroftoN

elytSydoB

0 ydobnotyR 0

erawdraHyrosseccA

023456

enoN)8110-5025BT4(elcatpecerkcol-tsiwt,leetssselniatS

)9110-5025BT4(elcatpecerkcol-tsiwt,)FDVP(ranyK)0210-5025BT4(draugelbisrembuS,CVP

)1210-5025BT4(draugelbisrembus,leetssselniatS)0210-5159BT4(elcatpecerdedaerhT,)SPP(notyR

023456

elbaCrosneSlargetnI,erusaeMfostinU 5

–T0

155XBTroftoN teef,rotcennocCNBteef,sdaelniP/denniT 1

detcelesera)woleb(BJnehwesU 7,6

FT0

elbaCrosneSlargetnI,htgneL

–JJ

–BS

teefnihtgnelelohwretne)m8.8(tf03)m3.0(tf1xobnoitcnujhtiW 7,6

xobnoitcnujsseL 7,6

–JJ

–BS

155XBT X X X X X X X X X XegatnavdApetStxeN )noisremmI(elbisrembuS,kcol-tsiwT,enil-nI, 1

041@isp001(ylbmessArosneSPRO/HpydoBnotyR )C

rofsrosneSgnikcehc-flesnoituloShtiw()doRdnuorG


8

Specification

Applications3/4 in. NPT process connection, In-line,submersion (immersion)


690kPa (100 psi) at 80C (176F)

276kPa (40 psi) at 140C (284F)

Material

Body Kynar (PVDF) as standardJunction Wood or Teflon (PTFE)

Junction types Flush (Antimony and flat glass only)

Notched (recommended)

Flow-through

Specify insertion depth in code

Submersion/Immersion

With notched junction

Models TB(X)556 Kynar Sensors

Models TB556 & TBX556 Kynar SensorsModels TB(X)556 Sensors are threaded style sensors suitablefor submersion (immersion) and insertion into the process pipes.

Mounting thread size is 3/4 in. NPT.

The sensor is available in several insertion lengths from thestandard 40mm (1.5 in.) to a maximum of 127mm (5 in.).

The sensor body is molded from chemically resistant Kynar(PVDF).

Sensor with Junction Box

238.1 (9.38)120.0 (4.73)

3/4 in.NPTConduit Port

(2 Typ.)

71.1(2.80)

95.0(3.74)

3/4 in. NPT Electrode

22.2 (0.80)

Note.27.9mm (1.1 in.)insertion depth notavailable on TBXAdvantage sensorswith solution grounds

27.9 (1.10) Min.38.1 (1.5) Standard

As Specified up to 127.0 (5.00) Max.(see Note)

Rear of Sensor andCable to be Sealedin Conduit or Pipe(Customer Supplied)

3/4 in. Coupling(Customer Supplied)

Kynar Body

Conduit(Customer Supplied)

3/4 in. NPT7/8 in.WrenchFlats

3/4 in. NPT

Notched Sensor

127.0(5.00)

Notched SensorSubmersible Application s

Notched SensorFlow Applications

SampleOutlet

SampleInlet

3/4 in. Tee(customer Supplied)




9


Notes.1) Antimony pH electrodes supplied only with flush junctions (codes A & B).

2) Not available for, Redox (ORP), or Antimony, pH, electrodes (codes 5 & 6).


4) Flush junctions for flat glass pH and Antimony electrodes only (codes 1 & 6).

5) Notched junctions not available for Antimony electrodes.

6) Manufactured as 1.5 in.depth, includes cable strain relief.

7) There are 2 options to connect TB556 to TB82 or TB84 transmitters:



8) For direct conection to type TB82, TB84, 4630/35 and AX46 transmitters, or other supplier devices, using terminal blocks.

9) TB556: junction box or submersible (immersion) connector mounted on sensor. Cable length approx. 102mm (4 in.). Requires extension cable for Temperaturecompensator code must be 0, 2 or 4.

10) TB(X)556: junction box mounted on sensor. Cable length approx. 102mm (4 in.). Requires extension cable for connection to transmitter. If junction box is orderedseparately and longer cable lengths are required, enter cable length in code for integral cable.

srosneSetats-diloSdradnatSdoRdnuorGnoituloSoN

petStxeN )noisremmI(elbisrembuS,dedaerhT,enil-nIylbmessArosneSPRO/HpydoBranyK

041@isp04( 09@isp001;C )C 655BT X X X X X X X X

edortcelEgnirusaeM

1256FJ

001ot01(ssalgtalF 09tawolfhtiwsetalucitraphgihrof)Hp41ot0,C 1

001ot0(Hp,ssalG )Hp21ot0,C)PRO(xodeR,munitalP08ot02–(Hp,ynomitnA )Hp11ot3,C 1


1256FJ

noitasnepmocomrehTlargetnI

01

655XBTroftoN3

655XBTroftoN





01234

noitcnuJdiuqiL

ABDE

ecnereferpetStxeN,hsulf,dooW 4

ecnereferpetStxeN,hsulf,nolfeT 4

ecnereferpetStxeN,dehcton,dooW 5

ecnereferpetStxeN,dehcton,nolfeT 5

ABDE


123


yolletsaH 2B


lairetaMgniR-O

1234

notiV

MDPEenociliS

zerlaK


elytSydoB

0–15

0–50

655XBTroftoNeborp)noisremmI(elbisrembuS 6

htpednoitresnI.ni1.1htpednoitresni.ni5.1htpednoitresni.ni0.5

0115

0150

elbaCrosneSlargetnI 7

–T0


detcelesera)woleb(BJnehwesU 01,9

FT0


–JJ

–BS

teefnihtgnelelohwretne)m8.8(tf03ot)m3.0(tf1xobnoitcnujhtiW 01,9

xobnoitcnujsseL 01,9

–JJ

–BS

655XBT X X X X X X X X X X egatnavdApetStxeN )noisremmI(elbisrembuS,dedaerhT,enil-nI,ylbmessArosneSPRO/HpydoBranyK

isp04( 041@ 09@isp001C )C

rofsrosneSgnikcehc-flesnoituloShtiw()doRdnuorG


10

Models TB557 & TBX557 Hot-Tap Retractable SensorsModels TB(X)557 sensors are hot tap, ball valve insertionsensors. They enable sensor maintenance or replacementwithout interrupting the process.

An integral safety anti-blowout lip is incorporated into the sensordesign, preventing accidental sensor removal. Unlike chainrestraints, this safety-by-design is an integral part of the sensors'construction.

The sensor is inserted through a standard 11/2 in. or 11/4 in. fullport ball valve. Ease of disassembly aids sensor replacement.

Connection to a ball valve is by compression fitting available ineither hand-tight with 11/4 in. NPT threads or wrench-tight with1 in. NPT threads.

Additional fittings enable the assembly to be flushed and drainedin situ and uses a 11/2 in. NPT threads for connection to the ballvalve.

Specification

Applications

Insertion, Hot-tap


690kPa (100 psi) at 80C (176F)276kPa (40 psi) at 140C (284F)

Features

Insert/retract without disturbing process flow

Replaceable electrodeAnti-blowout lip

No internal high-impedance connection

Material

Electrode Body Kynar (PVDF) as standardSensor sheath variants 316 stainless steel

Hastelloy or Titanium

External O-rings Viton

Junction Wood or Teflon (PTFE)Junction types Flush (Antimony only)

Notched (recommended)

Lengths Standard 400mm (16 in.)

Maximum 910mm (36 in.)

Overall Dimensions – Compression Fittings

11/4 in. Full Post Ball Valveor 11/2 in. Ball Valve

Compression Fitting

Process Line / Vessel

1/4 in. NPT Flushing Port21/2 in. Dia.

Hand-tight

13/4 in. Hex.

11/4 in. NPT

11/2 in. Hex.13/8 in. Hex.

1 in. NPT

97.8(3.85)

66.7(2.63)

Wrench-tight

Wrench-tightcompression fitting

Hand-tightcompression fitting

1/4 in. NPT Flushing Port

11/2 in. NPT184.7(7.27)

Wrench-tight flush and draincompression fitting

11/2 in. NPT

Hand-tight flush and draincompression fitting

199.4(7.85)


Models TB557 and TBX557 Sensors

Overall Dimensions – Ball Valve


11

…Overall Dimensions – Models TB(X)557

Viton O-Rings Sheath Replaceable SensorKynar Back Piece

Hand-tight Compression Fitting

Installation Detail

26.7 Dia(1.05)22.9 Dia

(0.90)

21.0 Dia(0.83)

ReferenceJunction

Electrode

188(7.40)

No. 019 VitonO-Rings

222.9 (8.78) (Other Lengths Available)27.9(1.10)

Replacement Sensor Detail

Kynar BodyNo 019 VitonO-Rings

316 Stainless SteelTitanium or Hastelloy-CSheath

3/4 in. NPT

95.0 (3.74)

71.1(2.80)

120.0 (4.73)

3/4 in ConduitPort (2 Typ.)

25.4 Dia(1.00) Kynar Back Piece Anti-Blowout Lip

11/4 in. NPT

Optional Compression FittingHand-tight 316 Stainless Steelor Titanium

97.8 (3.85)

11/4 in. NPT Full Port Ball Valve

11/4 in. 316 Stainless SteelClose Nipple

Sensor

Optional Compression FittingWrench-tight 316 Stainless Steel,Titanium or Hastelloy-C

66.7(2.63)

27.9(1.10)

26.7 Dia(1.05) 3/4 in. NTP 1 in. NTP

11/4 in. NPT Full Port Ball ValveReducing Bushing

11/4 in. Close NippleSensor

Installation Detail

Wrench-tight Compression Fitting 28.6(1.13)



12


srosneSetats-diloSdradnatSdoRdnuorGnoituloSoN petStxeN ,ydoBranyK,paTtoH,noitresnIevlaVllaB

041@isp04(ylbmessArosneSPRO/Hp 09@isp001;C )C 755BT X X X X X X X X

edortcelEgnirusaeM

1256FJ

001ot01(HpssalgtalF 09tawolfhtiwsetalucitraphgihrof)Hp41ot0,C 001ot0(Hp,ssalG )Hp21ot0,C

)PRO(xodeR,munitalP08ot02–(Hp,ynomitnA )Hp11ot3,C 1


1256FJ

rotasnepmocerutarepmeTlargetnI

01–3–

755XBTroftoN

755XBTroftoN





01234

noitcnuJecnerefeR

ABDE

ecnereferpetStxeN,hsulf,dooW 4

ecnereferpetStxeN,hsulf,nolfeT 4

ecnereferpetStxeN,dehctoN,dooW 5

ecnereferpetStxeN,dehctoN,nolfeT 5

ABDE


123


2ByolletsaH


lairetaMgniR-O

1234

notiVMDPE

enociliSzerlaK 6


elytSydoB

07ABFGHJKLMNPRS

ylnoedortcele755)X(BTtnemecalpeRhtaehsmuinatiT.ni61

htaehsCyolletsaH.ni61htaehsleetSsselniatS613.ni61

htaehsmuinatiT.ni02htaehsmuinatiT.ni42htaehsmuinatiT.ni03

htaehsCyolletsaH.ni02htaehsCyolletsaH.ni42htaehsCyolletsaH.ni03

htaehsleetSsselniatS613.ni02htaehsleetSsselniatS613.ni42htaehsleetSsselniatS613.ni03

htaehsmuinatiT.ni63htaehsleetSsselniatS613.ni06

07ABFGHJKLMNPRS

erawdraHyrosseccA 7

01234

enoN 8

thgit-hcnerw,gnittifnoisserpmocleetSsselniatS613thgit-hcnerw,gnittifnoisserpmocCyolletsaH

thgit-dnah,gnittifnoisserpmocleetSsselniatS613thgit-dnah,gnittifnoisserpmocmuinatiT

01234

elbaCrosneSlargetnI 9

–T0


detcelesera)woleb(5Jot1JroBJnehwesU 21,11

FT0


–JJJJJJ

–B12345

teefnihtgnelelohwretne)m8.8(tf92ot)m3.0(tf1 31

xobnoitcnujhtiW 41

htaehs.ni61rofrosnestnemecalpeR 51





–JJJJJJ

–B12345

755XBT X X X X X X X X X X petStxeN ,egatnavdA ,paTtoH,noitresnIevlaVllaBylbmessArosneSPRO/HpydoBranyK

041@isp04( 09@isp001;C )C

rofsrosneSgnikcehc-fles

dnuorGnoituloShtiw()doR


13

10) For direct connection to type TB82, TB84, 4630/35 and AX46 transmitters,or other supplier devices, using terminal blocks.

11) TB557: junction box mounted on sensor. Cable length varies to match bodylength style. Order code for body style and accessory hardware anythingexcept zero. Requires extension cable. Order code for temperaturecompensator must be 0, 2 or 4.

12) TB(X)557: junction box mounted on sensor. Cable length approx. 102mm (4in.). Order code for body style and accessory hardware anything exceptzero. Code – # # # # # # # 0, J, B. Requires extension cable. If junction boxis ordered separately and longer cable lengths are desired, enter cablelength in integral sensor code.

13) Standard cable length of 4 ft (1.2m) as measured from rear of sensorassembly with 16 in. sheath only. Max. 29 ft (8.8m) cable only available with16 in. sheath. Longer sheaths decrease length accordingly.

14) Applicable to sensors with junction boxes only.

Notes.1) Antimony pH electrodes supplied only with flush junctions (codes A & B).

2) Not available for, Redox (ORP), or Antimony, pH, electrodes (codes 5 & 6).

3) Not available for fluoride-resistant electrodes (code F).Compatible with TB82, TB84, 4630/35 and AX46 instruments.

4) Flush junctions for Antimony electrodes only (code 6).

5) Not available for Antimony electrodes (code 6).

6) Kalrez O-rings only for solution ground sleeve. External O-rings are Viton.External Kalrez O-ring kits available separately.

7) Standard hardware kits have Viton O-rings.

8) Applicable for all body styles. Mandatory for replacement sensors

(code 0 in Body Style section).

9) There are 2 options to connect TB557 to TB82 or TB84 transmitters:

Option 1 – use BNC/TC to PIN adapter with conduit fitting or BNC/TC toPIN adaptor. In either case temperature compensator code must be2 or 4.

Option 2 – select T in integral sensor code, not designed for use withextension cables or junction box.


14

Models TB561 & TBX561 Sterizable SensorsModels TB(X)561 sensors are designed for sterilizable or in-lineapplications and for measurements in process vessels or linesrequiring periodic sterilization or cleaning. They are also used inthe TB18 Safe-T-Clean valve and 4TB9515-0190 stainless steelflow cell.

The sensors are available with a bushing and union nut but canalso be retro-fitted into standard DN25 bushings with 0.983 in.to 0.995 in. internal diameters. All hardware required for use withthe TB18 Safe-T-Clean or 4TB9515-0190 Flowcell is includedwith valve or Flowcell when purchased.

Specification

Applications

Batch processing with steam or chemical sterilization, fermenters,glass-lined reactors, pharmaceuticals, food and beverage

Max. pressure/temperatures

690kPa (100 psi) at 90C (176F)

448kPa (65 psi) at 121C (250F)

276kPa (40 psi) at 140C (284F)

Material

Electrode body Kynar (PVDF) as standard

Junction Wood or Teflon (PTFE)

Junction types Flush

Notched

Insertion depths

70mm, 100mm, 150mm or 200mm

(100mm required for TB18 Safe-T-Clean valve and Flowcell)



L

Kynar SensorBody

Holder Nut

Flow cell (Requires 100 mm sensor)

No. 020 VitonO-Ring

152.4 (6.00)

Order Code 070:L = 70.0 (2.76)Order Code 100:L = 100.0 (3.94)Order Code 150:L = 150.0 (5.91)Order Code 200:L = 200.0 (7.87)

Front View

Vessel WallWeld

11/4 in. BSP

15

38.1(1.50)

Tank Bushing

11/4 in. BSP

Note.Holder nut slides over sensorand threads onto tank bushing

198.1(7.8)

166.4(6.55)

38.1(1.50)71.9(2.83)134.9(5.31)

NOTES.1. DASHED LINES REPRESENT DIMENSIONS OF FLOW CELL KIT

WITH SWAGE LOCK FITTINGS.2. FLOW CELL KIT WITHOUT SWAGE LOCK FITTINGS 4TB9515-0223

FLOW CELL KIT WITH SWAGE LOCK FITTINGS 4TB9515-0190

Safe-T-CleanSensor Valve TB18(Requires 100mmsensor with flushliquid junction)

1/2 in. NPT x 1/4 in.Swage Lock Fitting

(3 Typ)83.5(3.29)

38.5 (1.52)



15


Notes.1) For direct connection to type TB82, TB84, 4630/35 and AX46 transmitters or other supplier devices, using terminal blocks.

2) Not available for Platinum, Redox (ORP), electrodes (code 5).

3) Kalrez O-rings only for solution ground sleeve. External O-rings are Viton. External Kalrez O-ring kits available separately.

4) Insertion depth measured from wetted face of sensor flange to tip of guard.

5) TB561only. There are two options to connect to TB82 or TB84 transmitters:


Option 2 – select T in integral cable code, not designed for use with extension cables or junction box .

6) TB561: junction box mounted on sensor. Cable length approx. 102mm (4 in.). Requires extension cable. If junction box is ordered separately and longer cable lengthsare required enter length under code position for integral cable.

7) Not compatible with all TB18 Safe-T-Clean valve styles.

8) Required for use in most TB18 Safe-T-Clean valves.

9) Required for use with TB18 Safe-T-Clean valves and 4TB9515-0190 Flowcell. Consult TB18 Product Specification sheet for comprehensive measuring electrodeselection.

srosneSetats-diloSdradnatSdoRdnuorGnoituloSoN petStxeN ylbmessArosneSPRO/HpydoBranyKelbaziliretS

121@isp56( )C165BT X X X X X X X X X

edortcelEgnirusaeM

125FJ


001ot0(Hp,ssalG )Hp21ot0,C)PRO(xodeR,munitalP


125FJ

rotasnepmoCerutarepmeTlargetnI

01

165XBTroftoN3

165XBTroftoN



sdaeldenniT001tP 2

rotcennocelbacnoisnetxE001tP 2

01234

noitcnuJecnerefeR

ABDE


petStxeN,dehcton,dooW 7

petStxeN,dehcton,nolfeT 7

ABDE


123


2ByolletsaH


lairetaMgniR-O

1234

notiVMDPE

enociliSzerlaK 3


htpeDnoitresnI 4

0112

7050

0000

mm07mm001 9

mm051mm002

0112

7050

0000


–T0


detcelesera)woleb(SJ/BJnehwesU 7,6

FT0

elbaCrosneSlargetnI

–JJ

–BS

teefnihtgnelelohwretnem8.8)tf03(ot)m3.0(tf1xobnoitcnujhtiW 7,6

relpuocelbisrembus/xobnoitcnujsseL ,6 7

–JJ

–BS

165XBT X X X X X X X X X X X egatnavdApetStxeN elbaziliretS, 1

121@isp56(ylbmessArosneSPRO/HpydoBranyK )C rofsrosneS

htiw(gnikcehc-fles)doRdnuorGnoituloS


16

Models TB562 & TBX562 Sanitary SensorsModels TB(X)562 sensors are designed for processes needingthe use of sanitary (hygienic) fittings. These sensors have a11/2 in. tri-clamp flange fitting and are suitable for processesusing steam or chemical cleaning.

Specification

Applications

Food & Beverage, Dairy,Pharmaceuticals


690kPa (100 psi) at 90C (176F)

448kPa (65 psi) at 121C (250F)276kPa (40 psi) at 140C (284F)

Material

Electrode body Kynar as standard

External O-ring Viton

Junction Wood or Teflon (PTFE)Junction types Flush

Mounting 11/2 in. polished sanitary tube flange

1 in. and 11/2 in. tri-clamp for flush style

Models TB(X)562 Sensors


29.0 (1.14) Dia.Standard Style

4.6 (0.18)46.2(1.82)

53.3 (2.10)139.7 (5.50)

86.4 (3.40)

34.3 (1.35) Dia.

69.9 (2.75)

52.1 (2.05)Flange Gasket(Customer Supplied)

Standard Style

3/4 in. NPT

11/2 in. Tri-Clamp Tee(Customer Supplied)

No. 216 VitonO-Ring

3/4 in. NPT

Liquid Junction

Flush Style

Kynar Body3.6 (0.14)Radius

SanitaryFlange

50.5 (1.99)

34.3 (1.35) Dia.

147.3 (5.80)

Flush Style

SanitaryFlange Gasket(Customer Supplied)

Vessel(CustomerSupplied)

Wall

26.7(1.05)

Dia.Front View

69.9(2.75)

139.7(5.50)

11/2 in. Kynar Tri-ClampFlange Mount Sensorwith TemperatureCompensator

ElectrodeGroove forSanitary Gasket

139.7 (5.50)

Dimensions in mm (in)


17


Notes.1) For direct connection to type TB82, TB84, 4630/35 and AX46 transmitters or other supplier devices using terminal blocks.

2) Not available for Platinum, Redox (ORP), electrodes (code 5).

3) TB562 only. There are two options to connect to TB82 or TB84 transmitters:



4) TB562: junction box mounted on sensor. Cable length approx. 102mm (4 in.). Requires extension cable. Temperature compensator code position must be 0, 2 or4.

5) TB(X)561: when selecting JB or JS cable length is approx. 102mm (4 in.). Requires extension cable. If junction box is ordered separately and longer cable lengths arerequired enter length under code position for integral cable.

srosneSetats-diloSdradnatSdoRdnuorGnoituloSoN petStxeN rosneS)PRO(xodeR/HpelbaziliretS

121@isp56(ylbmessArosneSydoBranyK )C265BT X X X X X X X X

edortcelEgnirusaeM

125FJ

001ot01(HpssalgtalF 09tawolfhtiwsetalucitraphgihrof)Hp41ot0,C 001ot0(Hp,ssalG )Hp21ot0,C

)PRO(xodeR,munitalP08ot01(tnatsiser-ediroulF,Hp,ssalG )Hp21ot0,C

041ot5(erutarepmethgih/ssalgtnatsiser-taoC )Hp41ot0,C

125FJ


01–3–

265XBTroftoN

265XBTroftoN



sdaeldenniT001tP 2

rotcennocelbacnoisnetxE001tP 2

01234

noitcnuJecnerefeR

AB


AB


1 leetssselniats613 265BTroftoN

lairetaMgniR-O

123

notiVMDPE

enociliS


lairetaMydoB

0 )FDVP(ranyK 265BTroftoN 0

elytSydoB

01

pmalc-irT.ni5.1,dradnatSpmalc-irT.ni5.1/0.1,hsulF

01


–T0


detcelesera)woleb(SJroBJnehwesU 5,4

FT0

elbaCrosneSlargetnI

–JJ

–BS

teefnihtgnelelohwretne)m8.8(tf92ot)m3.0(tf1xobnoitcnujhtiW 5,4

xobnoitcnujsseL 5,4

–JJ

–BS

265XBT X X X X X X X X X XegatnavdApetStxeN rosneS)PRO(xodeR/HpelbaziliretS, 1

121@isp56(ylbmessArosneSydoBranyK )C rofsrosneSgnikcehc-flesnoituloShtiw()doRdnuorG


18

Specification

Applications

High pressure, hazardous materials


2065kPa (300psi) at 140C (284F)

Features

Insert/Retract without disturbing process

Retraction housing for safety

Taps for flushing or pressurizing

Material

Electrode body Kynar (PVDF)

Ball-valve/hardware 316 stainless steel(other materials on request)

External O-rings VitonJunction Wood or Teflon (PTFE)

Junction Types Flush (Antimony only)Notched (recommended)


Overall Dimensions – Models TBX564

41(1.60)

38(1.50)

41(1.61)

334(13.1)

174(6.85)

13(0.50)

3/4 in. Conduit Port (2 Typ.)

Note.All pipe threads have Loctite PST sealant applied at the Factory.

120.0 (4.73)

3/4 in. NPT

95.0 (3.74)

71.1(2.80)

63.5 Max.(2.50)

3/4

O-Ring

21/8 in.Wrench Flats

11/4 in. NPT

43.2(1.70)

110 (4.33)268 (10.6)

Weld

11/2 in.316 Stainless SteelBall Valve

Reducing Coupling Guide

ReplaceableKynar Sensor

ExtractionHousing

End Cap

CompressionFitting with N o. 014Viton O-Ring

CompressionFitting1/2 in. NPT

1/2 in.Elbow

19/16 in.Wrench Flats (not shown)

No. 217 Viton

in. NPT

Insertion Assembly1/2 in. Tube, 1/8 in. Wall

1/4 in. 316 Stainless SteelPipe Plug (2 Typ.)

Interior O-Ring No. 115 Viton


Models TB(X)564 are high pressure, hot-tap, ball-valve, insertionsensors. They permit sensor maintenance or replacementwithout interrupting the process.

A retraction housing is provided for isolating the sensor bodyfrom the operator. Using 1/4 in. taps, the housing can be flushedduring retraction or pressurized before insertion.

Models TB564 & TBX564 High Pressure Hot-tap Retractable Sensors


19

Ordering Information – Models TBX564


2) Antimony electrodes only supplied with flush junctions (code A and B).

3) Not available for Platinum, Redox (ORP), or Antimony, pH, electrodes (code 5 and 6).


5) Not available for Antimony electrodes (code 6).

6) Kalrez O-rings for solution ground sleeve only. External O-rings are Viton. External Kalrez O-ring kits available separately.

7) Requires installation of BNC connector kit.

8) There are two options to connect TB564 to TB82 or TB84 transmitters:

Option 1 – use BNC/TC to PIN adapter with conduit fitting or BNC/TC to PIN adapter. In either case temperature compensator code must be 2 or 4.Option 2 – select T in sensor cable code, not designed for use with extension cables or junction box.

9) Junction box mounted on insertion rod. Cable length approx. 254mm (10 in.). Requires extension cable to connect to transmitter. Order code for temperaturecompensator must be 0, 2 or 4. If sensor is ordered without accessory hardware a junction box must be ordered separately.

10) Requires BNC field mount for replacement sensors.

11) Maximum pressure: 690 kPa (100 psi).

srosneSetats-diloSdradnatSdoRdnuorGnoituloSoN petStxeN , )PRO(xodeR/Hppat-toHerusserPhgiH 1 rosneS

041@isp003(ylbmessA )C465BT X X X X X X X X

edortcelEgnirusaeM

1256FJ


001ot0(Hp,ssalG )Hp21ot0,C)PRO(xodeR,munitalP08ot02(Hp,ynomitnA )Hp11ot3,C 2

08ot01(tnatsiser-ediroulFHp,ssalG )Hp21ot0,C041ot5(erutarepmethgih/ssalgtnatsiser-gnitaoC )Hp41ot0,C

1256FJ


01–3–

465XBTroftoN

465XBTroftoN





01234

noitcnuJecnerefeR

ABCDE

petStxeN,hsulF,dooW 2

petStxeN,hsulF,nolfeT 2

ecnerefeRpetStxeN,desseceR,nolfeT 3

petStxeN,dehctoN,dooW 5

petStxeN,dehctoN,nolfeT 5

ABCDE


123


2ByolletsaH


lairetaMgniR-O

1234

notiVMDPE

enociliSzerlaK 6


elytSydoB

0 ydobrosnesranyK,dradnatS 0

erawdraHyrosseccA

09A

enoN 7

ylbmessarosnes465)X(BTledoMetelpmoC htiw htiw htiw htiw htiw evlav-llaberawdrahrosnes465)X(BTledoM tuohtiw tuohtiw tuohtiw tuohtiw tuohtiw evlav-llab

09A


–T0

465XBTroftoN teef,rotcennocCNB 01

teef,sdaelniP/denniT 1 )dednemmoceR(detcelesera)woleb(SJ/BJnehwesU 9

FT0

elbaCrosneSlargetnI

–JJ

–BS

teefnihtgnelelohwretne)m8.8(tf03ot)m3.0(tf1xobnoitcnujhtiW 9

xobnoitcnujsseL 9

–JJ

–BS

465XBT X X X X X X X X X X egatnavdApetStxeN pat-toHerusserPhgiH)PRO(xodeR/Hp

041@isp003(ylbmessArosneS )C

rofsrosneSgnikcehc-fles



20

Specification

Applications

High pressure insertion


1380kPa (200 psi) at 140C (284F)

1725kPa (250 psi) at 100C (212F)

Features

2-piece sensor, double O-ring

Sealed body with stainless steel sleeve

Materials

Electrode body Ryton (Polyphenylene sulphide)

Outer sleeve 316 stainless steel(other materials available)

External O-rings Viton

Reference junction Wood or Teflon (PTFE)Junction type Flush

3/4 in. NPT Conduit Port (2 Typ.)

345.1(13.59)

71.1(2.80)

95.3 (3.74)

120.0(4.73)

Junction Box(see Note)

Kynar Adapter

Assembled Sensor

13/16 in. Wrench Flats1 in. NPT

3/4 in. NPT

Electrode

19.1(0.75)

Assembled Sensor

1 in. NPT 1 3/16 in. Wrench Flats 1 in. NPT

196.9 (7.75)6.4 (0.25)

12.7 (0.50)

28.6 (1.13)

Replaceable Body

Ryton BodyNo. 118 VitonO-Rings (2 Typ)

Stainless SteelSleeve

165.1 (6.50)30.1

(1.19)

26.67 (1.05)

316 StainlessSteel Body




Models TB(X)567 sensors are high pressure, in-line sensors.Their permissible pressure and temperature ratings are unique inthe industry.

After consultation with ABB, customers have exceeded thestandard ratings of 1724kPa (250 psi) at 100C (212F). Manyinstallations are operating at over 6895kPa (1000 psi).

The assembly comprises two parts: a 316 stainless steelhousing and a molded Ryton sensor body.

Models TB567 & TBX567 High Pressure In-Line Sensors


21



2) Antimony pH electrodes only supplied with flush junctions (code A and B).

3) Not available for Platinum, Redox (ORP), or Antimony, pH, electrodes (code 5 and 6).


5) Kalrez O-rings for solution ground sleeve only. External O-rings are Viton. External Kalrez O-ring kits available separately.

6) There are two options to connect TB567 to TB82 or TB84 transmitters:

Option 1– use BNC/TC to PIN adapter with conduit fitting or BNC/TC to PIN adapter. In either case temperature compensator code must be 2 or 4.

Option 2 – select T in sensor cable code, not designed for use with extension cables or junction box.

7) Junction box mounted on sensor. Cable length approx. 254mm (10 in.). Requires extension cable to connect to transmitter. Order code for temperature compensatormust be 0, 2 or 4. If sensor is ordered without accessory hardware a junction box must be ordered separately.

srosneSetats-diloSdradnatSdoRdnuorGnoituloSoN petStxeN )PRO(xodeR/HperusserPhgiHeniL-nI

041@isp002(ylbmessArosneS )C765BT X X X X X X X X

edortcelEgnirusaeM

256FJ

001ot0(Hp,ssalG )Hp21ot0,C)PRO(xodeR,munitalP08ot02(Hp,ynomitnA )Hp11ot3,C 2

08ot01(tnatsiser-ediroulFHp,ssalG )Hp21ot0,C041ot5(erutarepmethgih/ssalgtnatsiser-taoC )Hp41ot0,C

256FJ


01–3–

765XBTroftoN

765XBTroftoN





01234

noitcnuJecnerefeR

ABC


ecnerefeRpetStxeN,dessecer,nolfeT 9

ABC


123


2ByolletsaH


lairetaMgniR-O

1234

notiVMDPE

enociliSzerlaK 5


elytSydoB

0 ydobrosneS765)X(BTledoM 0

erawdraHyrosseccA

0D

enoNgnisuohrosnesleetssselniats613765)X(BTledoM

0D


–T0


detcelesera)woleb(SJ/BJnehwesU 7

FT0

elbaCrosneSlargetnI

–JJ

–BS

teefnihtgnelelohwretne)m8.8(tf03ot)m3.0(tf1xobnoitcnujhtiW 7

xobnoitcnujsseL 7

–JJ

–BS

765XBT X X X X X X X X X X egatnavdApetStxeN , )PRO(xodeR/HperusserPhgiHeniL-nI 1

041@isp002(ylbmessArosneS )C gnikcehc-flesrofsrosneS



22

Accessories

Automatic CleanersABB sensors are designed to resist fouling and pluggingespecially when placed in sufficient velocity.

Sometimes a lack of velocity or the precipitative properties of theliquid require the use of an automatic cleaner.

ABB supplies jet-wash type cleaning facilities for submersion(immersion) TB556 sensors with 11/2 in. insertion depth.

When coupled to a customer-supplied solenoid valve deliveringwash fluid, effective cleaning can be initiated by ABB pHinstrumentation such as the TB84PH or AX46 Series. Forexample, the TB84PH can be configured:

• Wash cycle time 0 to 99.99 hours

• Wash on time 0 to 999 seconds

• Wash recovery time 0 to 999 seconds

• Hold function ON or OFF

Hydraulic Cleaner with Models TB(X)556 Sensor

Corrosion Resistant Tubing(Customer Supplied)

Solenoid Valve(Customer Supplied)

CleaningSolution

1/4 in. Union(Customer Supplied)

1/4 in. 316 Stainless Steel

1/4 in. Polypropylene

2 in. NPT Threads

Set Screw to SecureDelivery Tube

Hydraulic CleanerHousing

(PVC)

3/4 in. NPT

pH Sensor with anInserton Depth of 1.5 in.

PCV or Stainless Steel3/4 in. Coupling

(Customer Supplied)

PCV or Stainless Steel3/4 in. Conduit

(Customer Supplied)

Configurable ParametersInclude: Cycle Time, On Time,Recovery Time and Hold Outputs

Hydraulic Cleaner Application Example

Specification

Model

4TB5205-0232

Materials

PVC, Polypropylene

316 stainless steel


690kPa (100 psi) at 40C (104F)

276kPa (40 psi) at 60C (140F)


23

pH/Redox (ORP) Transmitters

Model Description

TB82PH Advantage Series – 2-wire 24V d.c. 4 to 20mA

pH/Redox/pIon Transmitter – Certified intrinsically safe

– SMART-key programming

– On-line sensor diagnostics

– Configurable output

– Multi-temperaturecompensations

– Adjustable damping

– Hold output

– Configurable security code

– HART communication

– NEMA 4X/IP65 housing

– CE approved

TB84PH Advantage Series – AC-powered instrument

pH/Redox/pIon Transmitter – SMART-key programming

– On-line sensor diagnostics



– Adjustable damping

– Hold output


– NEMA 4X/IP65 housing

– CE approved

– 3-relay outputs

– 2 analog outputs

– Wash control function

AX460 – AC-powered instrument

pH/Redox Transmitter – Simple menu programming



– Hold output


– NEMA4/IP65 housing

– 1/4 DIN panel-mount housing

– CE approved

– 3 relay outputs

– 2 analog outputs

– Wash control function

…Accessories

Ball-Valves for TB(X)557 Sensors

Model Description

4TB5205-0174 11/4 in. 316 stainless steelIncludes 11/4 in. to 1 in. reducingbushing with 11/4 in. nipple.For wrench-tight compressionhardware 4TB4953-0024 only.

4TB5205-0175 11/2 in. Kynar (PVDF)Includes 11/2 in. to 1/4 in. reducingbushing with 11/2 in. nipple.For wrench-tight compressionhardware 4TB4953-0019 only.

4TB5205-0217 11/4 in. 316 stainless steelIncludes 11/4 in. nipple.For hand-tight compressionhardware 4TB4953-0006 only.

4TB5205-0218 11/2 in. Kynar (PVDF)Includes 11/2 in. to 11/4 in.reducing bushing with 11/2 in.nipple.For hand-tight compressionhardware 4TB4953-0060 or4TB4953-0065 only.

4TB5205-0254 11/2 in. 316 stainless steelIncludes 11/2 in. to 11/4 in.reducing bushing with 11/2 in.nipple.For hand-tight compressionhardware 4TB4953-0060 only.

4TB5205-0255 11/2 in. 316 stainless steelIncludes 11/2 in. to 1 in. reducingbushing with 11/2 in. nipple.For hand-tight compressionhardware 4TB4953-0024 only.

Acknowledgements

Hastelloy® is a registered trademark of Haynes International Inc.

Halar® is a registered trademark of Ausimont USA Inc.

Kalrez® and Viton are registered trademarks of DuPont Dow Elastomers L.L.C.

Kynar® is a registered trademark of Elf Atochem North America Inc.

LOCTITE® is a registered trademark of Loctite Corporation

Ryton® is a registered trademark Chevron Phillips Chemical Company

Teflon® is a registered trademark of E.I. DuPont de Nemours Company Inc.

Next Step™ and Next Step Advantage™ are trademarks of ABB Automation Inc.


SS

/TB

X5Is

sue

3

ABB Inc.Analytical Instruments9716 S. Virginia St., Ste. EReno, Nevada 89521USATel: +1 775 850 4800Fax: +1 775 850 4808

ABB Inc.125 E. County Line RoadWarminsterPA 18974USATel: +1 215 674 6000Fax: +1 215 674 7183

ABB has Sales & Customer Supportexpertise in over 100 countries worldwide

www.abb.com

ABB LimitedOldends Lane, StonehouseGloucestershireGL10 3TAUKTel: +44 (0)1453 826661Fax: +44 (0)1453 829671

The Company’s policy is one of continuous productimprovement and the right is reserved to modify the

information contained herein without notice.

Printed in UK (11.05)

© ABB 2005

data sheet single and dual input analyzers ss/ax4ph issue 7 for...

Documents