d2352 bios setup utility for primergy rx600...

PRIMERGY

D2352 BIOS Setup Utilityfor PRIMERGY RX600 S3/TX600 S3 Reference ManualHans-Joachim KnebaFujitsu Siemens Computers GmbH Paderborn81730 Muniche-mail: email: [email protected].: Fax: (++49) 700 / 372 00000D2352Sprachen: En

Edition November 2005

This manual is printed on paper treated with chlorine-free bleach.

Comments… Suggestions… Corrections…The User Documentation Department would like toknow your opinion of this manual. Your feedback helpsus optimize our documentation to suit your individual needs.

Fax forms for sending us your comments are included inthe back of the manual.

There you will also find the addresses of the relevantUser Documentation Department.

Certified documentation according to DIN EN ISO 9001:2000To ensure a consistently high quality standard anduser-friendliness, this documentation was created tomeet the regulations of a quality management system which complies with the requirements of the standardDIN EN ISO 9001:2000.

cognitas. Gesellschaft für Technik-Dokumentation mbHwww.cognitas.de

Copyright and Trademarks

© c

ogn

itas.

Ges

ells

chft

für

Tech

nik-

Dok

um

enta

tion

mbH

200

5 P

fad

: D:\P

roje

kte

\235

2_B

IOS

\D23

52_

BIO

S.v

or

Copyright © 2005 Fujitsu Siemens Computers GmbH.

All rights reserved.Delivery subject to availability; right of technical modifications reserved.

All hardware and software names used are trademarks of their respective manufacturers.

http://www.cognitas.de

D2352

Contents1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.1 Notational Conventions . . . . . . . . . . . . . . . . . . . . . . 11.2 System Options Menu . . . . . . . . . . . . . . . . . . . . . . . 2

2 BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . 52.1 Keyboard Commands . . . . . . . . . . . . . . . . . . . . . . . 52.2 Accessing the BIOS Setup Utility . . . . . . . . . . . . . . . . . 72.3 Setup Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82.4 Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102.5 Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112.5.1 Processor #n Information . . . . . . . . . . . . . . . . . . . . 132.6 Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142.6.1 Configure Memory RAS and Performance . . . . . . . . . . . 162.6.1.1 View Configuration Details . . . . . . . . . . . . . . . . . . . 192.6.2 View and Configure Memory Board n . . . . . . . . . . . . . . 202.6.2.1 Configuring Memory Sparing . . . . . . . . . . . . . . . . . . 222.7 Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232.7.1 IDE Controller . . . . . . . . . . . . . . . . . . . . . . . . . . 242.7.2 Mass Storage . . . . . . . . . . . . . . . . . . . . . . . . . . 242.7.3 LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252.7.4 Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262.7.5 USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262.7.6 Serial Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . 272.7.7 PCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282.8 Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292.8.1 ASR&R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302.8.2 Console Redirection . . . . . . . . . . . . . . . . . . . . . . . 322.8.3 BMC Information . . . . . . . . . . . . . . . . . . . . . . . . . 332.8.4 LAN Management . . . . . . . . . . . . . . . . . . . . . . . . 332.8.5 SEL Logging . . . . . . . . . . . . . . . . . . . . . . . . . . . 342.9 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352.10 Save, Restore & Exit . . . . . . . . . . . . . . . . . . . . . . . 36

3 Power-On Self Test Codes . . . . . . . . . . . . . . . . . . . 373.1 Error Beep Codes . . . . . . . . . . . . . . . . . . . . . . . . 373.2 Progress Codes and Messages . . . . . . . . . . . . . . . . . 383.3 Error Codes and Messages . . . . . . . . . . . . . . . . . . . 41

4 BMC Diagnostics and Beep Code Generation . . . . . . . . 45

Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

D2352

Contents

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik

-Do

kum

ent

atio

n m

bH

20

05

Pfa

d: D

:\P

roje

kte\

2352

_BIO

S\D

2352

_BIO

S.iv

z

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

D2352 1

1 IntroductionMost systems are already configured by the manufacturer or the dealer. There is no need to run the BIOS Setup when starting the computer unless there is an error message.

The BIOS Setup allows you to configure the system functions and view and change device settings and view environmental information for the platform. When it is supplied, the device is set to factory default settings. Any changes you make take effect as soon as you save the settings and quit the BIOS Setup Utility.

The BIOS Setup interface consists of several screens, called pages. Each page contains information or links to other pages. The first page in Setup displays links for general categories. This links lead to pages containing specific config-uration settings.

Console Redirection

The BIOS Setup is functional through console redirection over various terminal emulation standards. This may limit some functionality due to compatibility. For example, colors, some keys or key sequences use and support for pointing devices may be limited.

1.1 Notational Conventions

The meanings of fonts and symbols used in this manual are as follows.

Continous text:

Typewriter textindicates system output.

Italics indicate menu entries.

Italics indicate default values of menu items.

I Supplementary information, remarks, and tips follow this symbol.

Ê Text which follows this symbol describes activities that must be performed in the order shown.

2 D2352

System Options Menu Introduction

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

1

Screen shots:

A ">" to the left of an item indicates that this item contains a submenu.

Angle brackets (<...>) indicate a finite set of values.

1.2 System Options Menu

During the boot process, after video initialization the system BIOS begins to display the boot progress on the screen (and in parallel on the LocalView LCD display of your server, if installed), the SCSI BIOS scan is displayed, followed by the BIOS splash screen. You will see a note telling you the key to press to access the System Options Menu.

Ê Press the key on the keyboard when you see the message.

In the System Options Menu boot information, options, and diagnostic utilities are displayed. There are no diagnostic utilities.

Figure 1: System Options menu: Screen layout

D2352 3

Introduction System Options Menu

Select the desired item by using the keys Ê or Ë and then press the [Enter] key:

Continue BootingSelect this item to boot from the device specified as first boot option by the Boot Manager. The item is selected by default, and will occur automat-ically after a pre-set time-out expires.

Boot ManagerSelect this item to boot from one of the listed boot devices. You may use this item if you do not want to boot from the device specified as first boot option. The following submenu is displayed:

Figure 2: System Options menu: Boot Manager submenu

I Your selection is only valid for the current system boot. At the next system boot, the settings in the Boot Options item of the Boot Maintenance Manager menu are valid again (see the following page).

The boot devices displayed should only be considered as an example. According to the current configuration and activating the Boot Mainte-nance Manager, the choices displayed may differ considerably.

4 D2352

System Options Menu Introduction

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

1

Boot Maintenance ManagerSelect this item to configure boot options and other boot environment variables. The following submenu is displayed:

Figure 3: System Options menu: Boot Maintenance Manager submenu

Boot OptionsSelect this item to modify the system boot order and add/delete boot options.

Driver OptionsSelect this item to modify the boot driver options.

Set Time out ValueSelect this item to modify the automatic boot time-out value.

Reset SystemSelect this item to reset the system.

BIOS Setup UtilitySelect this item to access the BIOS Setup Utility (see chapter “BIOS Setup Utility” on page 5).

Error ManagerSelect this item to view POST errors detected by the system (see chapter “Power-On Self Test Codes” on page 37).

D2352 5

2 BIOS Setup UtilityThis chapter describes the functions available for BIOS Setup. Use Setup to change the default system parameters. You can run BIOS Setup with and without the installed operating system. Setup stores most of the configuration values in battery-backed CMOS; the rest of the configuration is stored in flash memory.

The configuration takes effect when you restart the system. POST uses these values to configure the hardware. If the values and the current hardware do not match, POST generates an error message (see “Power-On Self Test Codes” on page 37). You must then run BIOS Setup to correct the configuration.

Each BIOS Setup Utility menu contains a number of features. Some features are used for informative purposes only, and other features are associated with a value field that you can configure. Depending on the security setting chosen and in effect, a menu item’s value may be changeable. If a value cannot be changed, the item’s value field is inaccessible.

2.1 Keyboard Commands

Keys Meaning Description

[Enter]

Ú

Execute command

Execute the selected feature:

– activate the highlighted submenu– display a pick list if the highlighted field is a value field– activate the highlighted value in a pick list, undo the

pick list, and return the focus to the parent menu– select a subfield for multi-valued features like time and

date

À Â Select menu

Navigate between the major menus in the menu selection bar and select the highlighted menu. The keys have no effect if a submenu or pick list is displayed.

Ê Ë Select item

Select the previous/next item in a menu item list, or the previous/next value in a pick list. The selected item must then be activated by pressing [Enter]/Ú.

¯¸ Select field

Navigate between fields (eg. from hours to minutes in the time item in the main menu).

6 D2352

Keyboard Commands BIOS Setup Utility

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

2

[+] [-] Change value

Change the value of the date or time item to the next/previous value. The keys scroll through the values in the associated pick list without displaying the full list.

[Esc] Exit Provides a mechanism for backing out of any field. It will undo the pressing of the [Enter]/Ú key.

Pressing this key:

– in any submenu, the parent menu is reentered– in any major menu, the exit confirmation window is

displayed asking NO/YES) for the changes that can be discarded:

– selecting NO or [Esc]:return to where you was before without affecting any existing settings

– selecting YES:exit setup and the BIOS continues with POST

[F9] Setup Defaults

Following message appears:

Load default configuration now? (Y/N)

– selecting Y (yes):all setup fields are set to their default values

– selecting N (no) or pressing [Esc]:return to where you was before [F9] was pressed without affecting any existing field values

[F10] Save and Exit

Following message appears:

Save Configuration changes and exit now? (Y/N)

– selecting Y (yes):all changes are saved and setup is exited

– selecting N (no) or pressing [Esc]:return to where you was before [F10] was pressed without affecting any existing field values

Keys Meaning Description

D2352 7

BIOS Setup Utility Accessing the BIOS Setup Utility

2.2 Accessing the BIOS Setup Utility

The BIOS Setup Utility is accessed from the System Options Menu.

Ê Boot the server (switching ON or warm boot).

After video initialization the system BIOS begins to display the boot progress on the screen, the SCSI BIOS scan is displayed, followed by the BIOS splash screen. At the BIOS splash screen you will see a note telling you the key to press to access the System Options Menu.

Ê Press the key on the keyboard when you see the message.

Ê Select BIOS Setup Utility by using the keys Ê or Ë and then press the [Enter] key.

Ê If you have assigned an administrator password, you must now enter this password and confirm it with the [Enter] key.

The Main menu of the Setup Utility is displayed on the screen.

I Make a note of the changed values in the Setup Utility,!

8 D2352

Setup Menus BIOS Setup Utility

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

2

2.3 Setup Menus

The BIOS Setup Utility provides seven major menus and a number of setup items:

Major menus Setup items

Main BIOS VersionSystem DateSystem TimeHide Diagnostic Messages During BootPOST Error Pause

Processor Core FrequencyBus FrequencyProcessor RetestBoot Processor NumberProcessor #<no.> InformationHyper-Threading TechnologyEnhanced Intel SpeedStep(R) TechnologyExecute Disable BitHardware PrefetcherAdj. Cache Line PrefetchEnhanced Halt StateIntel(R) Virtualization Technology

Memory Total MemoryEffective MemoryMemory Boards InstalledCurrent ConfigurationConfigure Memory RAS and PerformanceView and Configure Memory Board<A, B, C, D>

Devices IDE ControllerMass StorageLANVideoUSBSerial PortsPCI

D2352 9

BIOS Setup Utility Setup Menus

Explanation of what you see displayed on the screen

● You cannot select an item or change its value:

Either the item is configured or detected automatically, or you must select a different menu.

● The prompt Press Enter is displayed next to an item:

Press [Enter]/Ú to display a submenu that either uses the entire screen or a submenu with one or more items.

Server SM Error HaltASR&RConsole RedirectionBMC InformationLAN ManagementSEL LoggingWOL Resume from S5Reset on Fatal Error

Security Administrator Password isUser Password isSet Administrator PasswordSet User PasswordPassword on Boot

Save, Restore & Exit Save Changes and ExitDiscard Changes and ExitSave ChangesDiscard ChangesRestore DefaultsSave as user default ValuesRestore User Default Values

Major menus Setup items

10 D2352

Main BIOS Setup Utility

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

2

2.4 Main

Figure 4: Main menu

In this menu you can set general system parameters.

BIOS VersionDisplays the current BIOS version.

System DateSets the system date ([MM/DD/YYYY]). If you replace the battery, the default date is set to January 1998.

System TimeSets the system time ([HH:MM:SS]). If you replace the battery, the time is set to 00:00. (This is a 24-hour clock.)

Hide Diagnostic Messages During BootDiagnostic messages will be suppressed while the system boots (Enabled) or not (Disabled). If set to Enabled, the system will boot with logo and progress will be indicated.

POST Error PauseIf set to Enabled, the system will wait for user intervention on critical POST errors. If set to Disabled, the system will boot with no intervention, if possible.

D2352 11

BIOS Setup Utility Processor

2.5 Processor

Figure 5: Processor menu

This menu displays information about all the processors.

I You either cannot or should not modify any items on this menu. Consult your system administrator if you need to change an item.

Core FrequencyFrequency at which processors currently run.

Bus FrequencyCurrent frequency of the processor front side bus.

Processor RetestIf set to Enabled, the function retests all processors in the system during the next POST. This value resets to Disabled after the test has been run.

Boot Processor NumberNumber of the processor that is designated by the firmware to boot this system.

Processor #n InformationDisplays information about the desired processor (one link per processor supported).

12 D2352

Processor BIOS Setup Utility

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

2

Hyper-Threading TechnologyIf set to Enabled, the operating system can use all logical processor within a physical processor. If set to Disabled, the operating system can only use the 1st logical processor of the physical processor. Disabled should only be used if hyper-threading technology has not been correctly implemented in the operating system. This takes effect after next reboot.

Enhanced Intel SpeedStep(R) TechnologyIn time phases in which the CPU's capacity is not fully utilised, the clock frequency and the supply voltage level of the CPU can be reduced (Auto) or not (Disabled). This leads to a lower power consumption of the CPU, and therefore also to reduced heat development of the system. To fully support this mode, an interaction between the BIOS and the operating system is necessary.

Execute Disable BitEnables protection of executable memory areas (virus protection). The function is only effective if it is also supported by the operating system. Enabled enables the operating system to activate the Execute Disable feature of the processor. Disabled prevents the operating system from being able to activate the Execute Disable feature of the processor.

Hardware PrefetcherEnables a prefetch to the hardware (Enabled) or not (Disabled). With this item you can make performance settings for exceeding applications. Fujitsu Siemens Computers recommends for standard applications not to deviate from the default settings.

Adj. Cache Line PrefetchEnables a prefetch to the adjacent sectors. If set to Enabled, the CPU only reads whole cachelines otherwise only the sector of a cacheline, which contains the required data, is read (Disabled). With this item you can make performance settings for exceeding applications. Fujitsu Siemens Computers recommends for standard applications not to deviate from the default settings.

Enhanced Halt StateEnables reduction of power consumption, if the processor is in idle mode. The system performance can be somewhat decreased. If set to Enabled, the processor in idle mode is recognised and power consumption is reduced. Thus system performance can be affected. If set to Disabled, the processor operates in the standard mode. Power consumption in idle mode is not reduced.

D2352 13

BIOS Setup Utility Processor

Intel(R) Virtualization TechnologyAllows a platform to run multiple operating systems and applications in independent partitions (Enabled) or not (Disabled). With virtualization, one computer system can function as multiple “virtual” systems.

2.5.1 Processor #n Information

Figure 6: Processor Information submenu

This submenu displays information about the desired processor.

I You cannot modify any items in this menu.

Processor FamilyIdentifies family or generation of the processor.

Maximum FrequencyMaximum frequency the processor core supports.

Cache SizeSize of the processor cache.

14 D2352

Memory BIOS Setup Utility

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

2

CPUID RegisterCPUID register value identifies details about the processor model.

Thread n StatusPossible values are:

Boot ThreadMachine has booted using this thread.

Application ThreadThe thread is available to be used by the operating system.

Not InstalledProcessor or thread is not installed.

DisabledThe thread is disabled.

Thread n HealthPossible values: Healthy, Performance Restricted, Functionality Restricted, Failed, Not Installed.

2.6 Memory

Figure 7: Memory menu

D2352 15

BIOS Setup Utility Memory

This menu displays information about the memory available for the system.

I You either cannot or should not modify any items in this menu.

Total MemoryTotal good memory from all slots available for use by the system.

Effective MemoryAmount of memory that can be used by operating system. Effective memory may be less than total memory if some memory is used for redundancy.

Memory Boards InstalledMemory boards (A, B, C, D) plugged into the system.

Current ConfigurationCurrent memory configuration for the system (Maximum Compatibility, Maximum Performance, Mirror, RAID).

Configure Memory RAS and PerformanceSelect this item to view and configure Memory RAS (Reliability and Serviceability) and Performance (see section “Configure Memory RAS and Performance” on page 16).

View and Configure Memory Board nSelect this item to view and configure memory board features (see section “View and Configure Memory Board n” on page 20). One link per memory board is supported.

16 D2352


© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

2

2.6.1 Configure Memory RAS and Performance

Figure 8: "Configure Memory RAS and Performance" submenu

In this his submenu you can view and configure Memory RAS (Reliability and Serviceability) and Performance.

Hardware Memory TestMemory will be tested using hardware based engines on each board (Enabled) or not (Disabled).

Patrol ScrubHardware patrol scrub cleans correctable errors (Enabled) or not (Disabled).

Retest All System MemoryIf set to Enabled, this function retests all memory in the system (including disabled DIMMs) and enables memory which passes the test. The value resets to Disabled after the test has been run.

Sparing ThresholdSets the number of correctable errors (1 - 15) that can be logged in a period before sparing occurs (see section “Configuring Memory Sparing” on page 22). Period is 12 or 16 days depending on DDR Technology.

RAID Upgrade GapSize of reserved gap on each memory board for RAID memory capacity addition (Disabled, 512 MB, 1024 MB, 1536 MB, 2048 MB, 2560 MB, 3072 MB, 3584 MB, 4096 MB).

D2352 17


Desired Memory ConfigurationSelects a new memory configuration.

Max Performance

– default configuration in the BIOS Setup– allows BIOS to be configured for maximum memory performance– allows 4-way-/2-way-/1-way-interleave– does not support hot-add or hot-replace – allows to allocate ranks to serve as spare on each memory board

When the system does not allow for the desired memory configu-ration, the BIOS will configure the system memory to the Max Perfor-mance mode.

Max Compatibility

– allows for the most flexibility with DIMMs and memory boards– allows memory to be hot-added– does not support hot-replace – allows to allocate ranks to serve as spare on each memory board– allows one-way interleave only– the lowest performance of supported configurations

Mirror

– requires two boards (A and B or C and D) or four memory boards with equal memory capacity on each board

– supports hot-add or hot-replace of memory– the data is mirrored from one board to another which provides

redundancy but at the cost of halving the effective memory size

Please note that the Hot Add/Hot Replace operations require corre-sponding support in the operating system.

RAID

– provides redundancy by writing to three of the memory boards while one is reserved for redundant parity information

– allows for increasing the total amount of system memory by hot-upgrading or hot-swapping the existing boards with larger memory boards, based on the RAID Upgrade Gap set in the Configure Memory RAS and Performance menu

Please note that the Hot Add/Hot Replace operations require corre-sponding support in the operating system.

18 D2352


© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

2

View Configuration DetailsDisplays the Memory Configuration Details (see section “View Configu-ration Details” on page 19)

Set Memory Hotplug in SRAT tableProvides the ability to hot-replace and hot-add memory boards while the system is running (Yes) or not (No).

Configuring Mirror and RAID:

Ê Boot the server to the System Options Menu and select BIOS Setup Utility.

Ê Select the Memory/Configure Memory RAS and Performance menu.

Ê Set Desired Memory Configuration as Mirror and RAID respectively.

Ê Select View Configuration Details and ensure that Configuration Possible is set to Yes.

I If the item displays No, you may need to install more memory to meet the requirements for this configuration.

Ê Press [F10] to save changes and exit.

Ê Reboot the server to activate the changes.

I When a DIMM rank or a memory board fails, the system will continue to operate with the backed up information on the mirrored board. The system loses redundancy at this point, and will remain in this non-redundant state until the failing board and/or memory can be replaced. To ensure redundancy is continued, hot-replace feature can be used to replace the defective memory and its board while the system is operating.

D2352 19


2.6.1.1 View Configuration Details

Figure 9: View Configuration Details submenu

I You cannot modify any items in this submenu.

ConfigurationDisplays the memory configuration set on Item Desired Memory Configu-ration in the previous menu .

Max Effective SizeMaximum effective memory size results when no spares are configured. The actual effective size will be calculated on the next boot.

Min Effective SizeMinimum effective memory size results when the largest DIMMs are used as spare (auto spare configuration). The actual effective size will be calculated on the next boot.

CapabilitiesCharacteristics of the selected configuration:

Configuration PossibleIndicates whether the configuration selected is possible with the current installed memory (Yes or No). If No is displayed, you may need to install more memory to meet the requirements for the configuration selected.

20 D2352


© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

2

SparingIndicates whether the configuration selected supports sparing (Yes or No).

Hot ReplaceIndicates whether the configuration selected allows memory to be replaced while the system is running (Yes or No).

Hot AddIndicates whether the configuration selected allows memory to be added while the system is running (Yes or No).

Board InterleaveBoard interleave for the chosen configuration (1-Way, 2-Way, 4-Way, Up to 4-Way). In Up to 4-way interleave, the BIOS configures the best possible interleave for each memory range.

2.6.2 View and Configure Memory Board n

Figure 10: View and Configure Memory Board submenu

In this submenu you can view and configure memory board features.

D2352 21


Board StatusIndicates the status of memory board selected (Not Installed, Healthy, Using Spare, Disabled).

Retest Board MemoryIf set to Enabled, this function retests all DIMMs on the current board and re-enables the DIMMs that pass the test. The value resets to Disabled after the test has been run.

Reserve Rank for SpareIf set to Enabled (default Disabled), the BIOS sets aside the largest memory rank to serve as spare (see section “Configuring Memory Sparing” on page 22). When correctable errors on a bad rank surpasses the sparing threshold, it is replaced by a spare rank.

DIMM <1A, 1B, 2A, 2B>Possible values are:

Not InstalledDisplays the DIMMs and memory slots state: The slot is empty.

InstalledMemory is installed and healthy.

Installed/partialMemory is installed but only part of it is used.

FailedMemory has been reported as failed.

UnsupportedMemory type is unsupported.

22 D2352


© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

2

2.6.2.1 Configuring Memory Sparing

A rank on each memory board can be reserved as a "spare" and can only be used as a backup for another rank on the same memory board. The memory rank that is configured as spare is held in reserve and cannot be used by the operating system. To ensure that any failing rank will fit on the spare rank, the total memory of each memory board is reduced by the largest DIMM rank installed on the board. Hot removal can not be done when in a memory sparing configuration.

When the error rate for a failing rank exceeds the Sparing Threshold set, the contents of that rank are copied to the spare rank. The failing rank is disabled on subsequent system boots.

Ê Boot the server to the System Options Menu and select BIOS Setup Utility.

Ê Select the Memory/Configure Memory RAS and Performance menu.

Ê Set Desired Memory Configuration (see section “Configure Memory RAS and Performance” on page 16).

Ê Select View Configuration Details and ensure that Configuration Possible is set to Yes (see figure 9 on page 19).

I If the item displays No, you may need to install more memory to meet the requirements for this configuration.

Ê Verify Sparring is set to Yes (see figure 9 on page 19).

Ê Go back to Configure Memory RAS and Performance and set Sparring Threshold between 1-15 (see figure 8 on page 16).

Ê Go back to Memory and select View and Configure Memory Board n, where n is the memory board slot that is to be enabled as the spare.

Ê Verify Board Status displays Healthy.

Ê Set Rank Serving as Spare to Enabled.

Ê Press [F10] to save changes and exit.

Ê Reboot the server to activate the changes.

I When a failing rank switches to a spare, the system is in a non-redundant state and you will need to replace the defective memory during the next maintenance period to ensure redundancy is continued.

D2352 23

BIOS Setup Utility Devices

2.7 Devices

Figure 11: Devices menu

In this menu you can examine and set system parameters for built-in devices.

IDE ControllerExamines and sets IDE controller parameters.

Mass StorageExamines and sets mass storage controller’s parameters.

LAN Examines and sets Local Area Network (LAN) parameters.

VideoExamines and sets Video parameters.

USB Examines and sets USB controller parameters.

Serial PortsExamines and sets serial port parameters.

PCI Examines and sets PCI system bus parameters.

If a device is disabled, it is inaccessible to the operating system.

24 D2352

Devices BIOS Setup Utility

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

2

2.7.1 IDE Controller

Figure 12: IDE Controller submenu

In this submenu you can enable or disable all channels of the SATA controller and view which controller is set as primary master.

2.7.2 Mass Storage

Figure 13: Mass Storage submenu

D2352 25


In this submenu you can enable or disable the onboard SCSI controller and view if the RAID Activation Key is installed or not. The Enable On-board SCSI item is grayed out if RAID on Mother Board (RoMB) is enabled.

2.7.3 LAN

Figure 14: LAN submenu

In this submenu you can enable or disable both channels of the embedded LAN and view the MAC Addresses. If Enable On-board NIC ROM is enabled (default), the ROM for the onboard LAN is executed.

26 D2352


© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

2

2.7.4 Video

Figure 15: Video submenu

In this submenu you can enable or disable the onboard Video controller.

2.7.5 USB

Figure 16: USB submenu

D2352 27


In this submenu you can enable or disable the USB controller.

2.7.6 Serial Ports

Figure 17: Serial Ports submenu

In this submenu you can enable or disable the COM1 serial port and set the base I/O address and Interrupt Request (IRQ) line for the port.

28 D2352


© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

2

2.7.7 PCI

Figure 18: PCI submenu

In this submenu you can examine and set PCI system bus parameters.

Enable Slot <no.> ROMThe ROM scan of the device in the selected PCI slot will be enabled (Enabled) or not (Disabled).

Boot to ROMB Hard DriveSelect the ROMB hard drive as First or Last boot device. When set to Auto, the ROMB hard drive will boot in the order selected in Boot Manager.

D2352 29

BIOS Setup Utility Server

2.8 Server

Figure 19: Server menu

In this submenu you can examine and set server parameters.

SM Error HaltStops booting process if there is a system management error or config-uration change (Enabled). If set to Disabled, a warning message is displayed.

ASR&RAutomatic Server Recovery and Reboot.

Console RedirectionPerforms server management tasks over serial port.

BMC InformationBaseboard Management Controller information.

LAN ManagementLAN Management parameter settings.

SEL LoggingSystem Event Log (SEL) settings.

30 D2352

Server BIOS Setup Utility

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

2

WOL Resume from S5Allows the system to be switched on by means of network signals (Enabled) or not (Disabled). The LAN controller can switch on the system or not.

Reset on Fatal ErrorOn a fatal error an NMI will be triggered (Disabled) or the system will reset on fatal errors (Enabled).

2.8.1 ASR&R

Figure 20: ASR&R submenu

In this submenu you can set the ASR&R parameters.

O/S Boot TimeoutIf set to Enabled, this function specifies whether the system is to be rebooted if the OS cannot establish a connection with the server management firmware within a predefined time period (after startup). The item must be set to Disabled when installing the server. Otherwise, the system will reboot during installation.

O/S Boot WD Time (min)Time that the system has to complete the boot to OS and establish the connection with the server management firmware (0 - 100). A value of 0 means that the boot timer is inactive.

D2352 31


O/S Boot WD BehaviorAction to be taken if boot watchdog timeout expires (Continue, Reset, Power Cycle).

ASR&R Boot Delay (min)Time period for which the server must wait after a shutdown due to an error before it is automatically restarted (1 - 30, default 2).

Power Cycle DelayMinimum time in seconds that must pass until the system can be switched on after being switched off (0 - 15, default 5).

Boot Retry CounterNumber of boot retries if the O/S boot fails or any other critical error occurs (0 - 7, default 3).

Diagnostic SystemDefines whether or not RemoteView is to be started on reaching the number of system restarts set under Boot Retry Counter (PXE (Lan) Image or Disabled). If PXE (Lan) Image is chosen, the selected LAN in the Diagnostic Lan Device menu will be hooked at top of boot order.

Next Boot UsesDefines whether or not RemoteView is started at the next boot (Boot Option or Diagnostic System). By default, the selection of the Boot Manager will be used.

Diagnostic Lan DeviceSelect the LAN Device for Diagnostic PXE boot (Use Boot Order, LAN 1 or LAN 2). If Use Boot Order is selected, the first LAN device in the boot sequence will be used.

Temperature MonitoringIf set to Enabled, the system will be switched off if temperature exceeds operating range (default Disabled).

32 D2352


© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

2

2.8.2 Console Redirection

Figure 21: Console Redirection submenu

In this submenu you can set COM1 console redirection parameters (if Console Redirection is set to Enabled).

Console RedirectionPerforms server management tasks over serial port (Enabled) or not (Disabled).

Flow ControlDefines serial port communication protocol handshaking type (None, RTS/CTS, XON/XOFF, CTS/RTS+CD).

Baud RateDefines serial port transmission speed (9600, 19.2K, 36.4K, 57.6K, 115.2K).

Terminal TypePossible values are:

VT100+ (only works with English as selected language)

VT-UTF8 (uses unicode)

PC-ANSI (standard PC-type terminal)

D2352 33


2.8.3 BMC Information

Figure 22: BMC Information submenu

In this submenu BMC information is displayed.

2.8.4 LAN Management

Figure 23: LAN Management submenu

34 D2352


© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

2

In this submenu you can view or set the LAN IP parameters and view the MAC addresses. The parameters are loaded from BMC.

2.8.5 SEL Logging

Figure 24: SEL Logging submenu

In this submenu you can set SEL features.

Clear LogClears the System Event Log (if set to Enabled). The function executes as soon as Save, Restore & Exit is performed, then resets to Disabled.

Event Log Full ModeSpecifies whether or not the System Event Log can be overwritten.

MaintainIf the System Event Log file is full, no further events are entered. The System Event Log file must be cleared first before additional events can be entered. Older events have greater importance than newer ones in this case.

OverwriteIf the System Event Log is full, additional events overwrite the oldest entries of the System Event Log. Newer events have greater importance than the older ones in this case.

D2352 35

BIOS Setup Utility Security

2.9 Security

Figure 25: Security menu

In this menu you can set security features.

Administrator Password IsWhen you enter an administrator password, this item automatically changes to Installed. If no administrator password is set, Not Installed is displayed.

User Password IsWhen you enter your user password, this item automatically changes to Installed. If no user password is set, Not Installed is displayed.

Set Administrator PasswordAccess to the Setup utility is controlled via the administrator password (to enter a password, press Ú and follow the screen prompts).

Set User PasswordThe user password controls the boot process (to enter a password, press Ú and follow the screen prompts).

Password on BootRequires entry of a password before boot (Enabled) or not (Disabled). If set to Enabled, the system remains in secure mode until you enter the password.

36 D2352

Save, Restore & Exit BIOS Setup Utility

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

2

2.10 Save, Restore & Exit

Figure 26: Save, Restore & Exit menu

The following menu items are available to save, restore values and/or exit BIOS Setup.

Save Changes and ExitExits Setup and saves the changes in CMOS-RAM.

Discard Changes and ExitExits Setup without saving the changes to CMOS-RAM.

Save ChangesSaves the changes to CMOS-RAM and continue Setup.

Discard ChangesDiscards the changes and loads the previous settings from CMOS-RAM and continue Setup.

Restore DefaultsSystem Configuration Reset: loads the Setup default values during the next POST.

Save as User default ValuesSaves current values so they can be restored later.

Restore User Default ValuesRestore previously saved user default values.

D2352 37

3 Power-On Self Test CodesSwitching on the system causes POST to run and to pass control to the boot manager. POST checks the drive carriers, boards, processors, memory, keyboard and most installed devices.

After video initialization, the system BIOS begins to display the boot progress on the screen (see section “Progress Codes and Messages” on page 38). The SCSI BIOS scan is displayed, followed by the BIOS splash screen.

I It may take three minutes or longer for video to be displayed, depending on the amount of memory installed in the system.

The POST codes/messages are also displayed in parallel on the LocalView LCD (if installed), even before the video screen is operable.

The system emits a beep to indicate that POST has been completed.

If the system stops before the POST has been completed, it emits a beep code followed by an error message displayed on the screen to indicate a critical system error that requires immediate attention. You will find a list of the beep codes and related error messages generated by POST in the next section.

Take note of the messages displayed and write down the beep code you hear since this information is useful to your service representative.

3.1 Error Beep Codes

BIOS uses the POST error beep codes to inform the user on error conditions. The beep code will be followed by a visible code on POST progress LEDs on the system board.

Beeps Error Messages Description

1 Fatal error System halted because of an unspecified fatal error that was detected.

2 Processor error System halted because of a fatal error related to a processor was detected.

3 Memory error System halted because of a fatal error related to the memory was detected.

4 System board error System halted because of a fatal error related to the system board hardware was detected.

38 D2352

Progress Codes and Messages Power-On Self Test Codes

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

3

3.2 Progress Codes and Messages

After turning on the system, BIOS begins to display the boot progress on the screen (and on the LocalView LCD, if installed) and outputs the current boot progress on the POST progress LEDs on the system board.

Progress Code Progress Code Definition

Host Processor

0x10 Power-on initialization of host processor (Bootstrap Proc.)

0x11 Host processor cache initialization (including AP)

0x12 Starting Application processor initialization

0x13 SMM initialization

Chipset

0x21 Initializing a chipset component

Memory

0x22 Reading configuration data from memory (SPD on DIMM)

0x23 Detecting presence of memory

0x24 Programming timing parameters in the memory controller

0x25 Configuring memory parameters in the memory controller

0x26 Optimizing memory controller settings

0x27 Initializing memory, such as ECC init

0x28 Testing memory

PCI Bus

0x50 Enumerating PCI busses

0x51 Allocating resources to PCI busses

0x52 Hot plug PCI controller initialization

0x53 ... 0x57 Reserved for PCI bus

USB

0x58 Resetting USB bus

0x59 Reserved for USB devices

ATA/ATAPI/SATA

0x5A Resetting PATA/SATA bus and all devices

0x5B Reserved for ATA

D2352 39

Power-On Self Test Codes Progress Codes and Messages

SMBUS

0x5C Resetting SMBUS

0x5D Reserved for SMBUS

Locale Console

0x70 Resetting the video controller (VGA)

0x71 Disabling the video controller (VGA)

0x72 Enabling the video controller (VGA)

Remote Console

0x78 Resetting the console controller

0x79 Disabling the console controller

0x7A Enabling the console controller

Keyboard (PS2* or USB)

0x90 Resetting the keyboard

0x91 Disabling the keyboard

0x92 Detecting the presence of the keyboard

0x93 Enabling the keyboard

0x94 Clearing keyboard input buffer

0x95 Instructing keyboard controller to run Self Test (PS2 only)

Mouse (USB)

0x98 Resetting the mouse

0x99 Detecting the mouse

0x9A Detecting the presence of mouse

0x9B Enabling the mouse

Fixed Media

0xB0 Resetting fixed medium

0xB1 Disabling fixed medium

0xB2 Detecting presence of a fixed medium (IDE hard disk drive detection, etc.)

0xB3 Enabling/configuring a fixed medium

Removable Media

0xB8 Resetting removable medium

0xB9 Disabling removable medium

0xBA Detecting presence of a removable medium ( IDE CDROM detection, etc.)

0xBC Enabling/configuring a removable medium


40 D2352

Progress Codes and Messages Power-On Self Test Codes

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

3

BDS

0xDy Trying boot selection y (where y = 0 to F)

PEI Core

0xE0 Started dispatching early initialization modules (PEIM)

0xE2 Initial memory found, configured, and installed correctly

0xE1, 0xE3 Reserved for initialization module use (PEIM)

DXE Core

0xE4 Entered EFI driver execution phase (DXE)

0xE5 Started dispatching drivers

0xE6 Started connecting drivers

DXE Drivers

0xE7 Waiting for user input

0xE8 Checking password

0xE9 Entering BIOS setup

0xEA Flash update

0xEE Calling Int 19. One beep unless silent boot is enabled.

0xEF Unrecoverable boot failure/S3 resume failure

Runtime Phase/EFI OS Boot

0xF4 Entering Sleep state

0xF5 Exiting Sleep state

0xF8 OS has requested EFI to close boot services (ExitBootServices() has been called)

0xF9 OS has switched to virtual address mode (SetVirtualAddressMap () has been called)

0xFA OS has requested the system to reset (ResetSystem () has been called)

PEIM/Recovery

0x30 Crisis recovery has been initiated because of a user request

0x31 Crisis recovery has been initiated by software (corrupt flash)

0x34 Loading crisis recovery capsule

0x35 Handing off control to the crisis recovery capsule

0x3F Unable to complete crisis recovery


D2352 41

Power-On Self Test Codes Error Codes and Messages

3.3 Error Codes and Messages

The BIOS displays during the POST process POST Error Codes and Messages on the monitor via the BIOS splash screen. Parallel to the BIOS splash screen on the monitor, the codes/messages are also displayed on the LocalView LCD (if installed, see Operating Manual).

To view POST errors detected by the system on the monitor, the System Options Menu may be accessed by pressing a key on the keyboard at the BIOS splash screen and selecting the Error Manager option (see section “System Options Menu” on page 2).

The user can check POST error codes in the system event log (SEL) or via ServerView error-/event log.

The following table describes the meaning of system handling.

The following table describes error codes, the associated error message, and the system handling of the error.

Handling Setting Meaning

Warn Yes The error is of low consequence and will have little impact on system functionality (boot in a degraded state)

Log Yes The event will be stored in the system error log (SEL)

Display Yes The error message will be displayed to the console(s)

View Yes The user must view the error prior to booting

Boot No The system will not boot with this error

Halt Yes The system will not allow any further action

Code Error message Warn Log Display View Boot Halt

0100 Timer error Yes No Yes No Yes No

0103 CMOS Battery Failure No Yes Yes No Yes No

0104 CMOS Settings Wrong Yes No Yes Yes Yes No

0105 CMOS Checksum Failure No Yes Yes No Yes No

0108 Keyboard Locked No Yes Yes Yes No No

0109 Keyboard disabled due to a stuck key Yes No Yes No Yes No

010A Keyboard Interface Error No Yes Yes No Yes No

010B CMOS Memory Size Different No Yes Yes Yes Yes No

010C RAM R/W Test Failed Yes No Yes No Yes No

42 D2352

Error Codes and Messages Power-On Self Test Codes

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

3

010D External Cache Failure No Yes Yes Yes Yes No

0112 CMOS Time Not Set No Yes Yes Yes Yes No

0117 CD-ROM Disk 0 Error No Yes Yes Yes Yes No

011B Date/Time Not Set No Yes Yes Yes Yes No

0120 Configuration Cleared by User Yes Yes Yes No Yes No

0121 Password Cleared by User Yes Yes Yes No Yes No

0140 Refresh Timer Test Failed No Yes Yes Yes Yes No

0141 PCI Memory Allocation Error No Yes Yes Yes Yes No

0142 PCI IO Allocation Error No Yes Yes Yes Yes No

0146 Insufficient Memory to Shadow PCI ROM

No Yes Yes Yes Yes No

8110 Processor 1 Internal Error (IERR) Yes Yes Yes No Yes No




8120 Processor 1 Thermal Trip Error Yes Yes Yes No Yes No




8130 Processor 1 Disabled Yes Yes Yes No Yes No




8140 Processor 1 Failed FRB-3 Timer Yes Yes Yes No Yes No




8150 Processor 1 Failed Initialization on Last Boot

Yes Yes Yes No Yes No






D2352 43

Power-On Self Test Codes Error Codes and Messages



8160 Unable to apply BIOS update to processor 1








8170 Processor 1 L3 Cache Failed No Yes Yes Yes Yes No




8180 BIOS does not support current stepping for processor 1








8190 Watchdog Timer Failed on Last Boot Yes No Yes No Yes No

8192 Processor L3 Cache Size are Different No Yes Yes Yes Yes No

8193 Processor Stepping are Different No Yes Yes Yes Yes No

8194 Processor Families are Different No Yes Yes Yes Yes No

8195 Processor and Front Side Bus Speeds are Different. System Halted

No Yes Yes Yes No Yes

8196 Processor Models are Different No Yes Yes Yes Yes No

8197 Processor L3 Speeds are Different No Yes Yes Yes Yes No

8300 Baseboard Management Controller Failed


8301 Front Panel Controller Failed No Yes Yes Yes Yes No

8205 Hot-swap Controller Failed No Yes Yes Yes Yes No

8420 Intelligent System Monitoring Chassis Opened



44 D2352

Error Codes and Messages Power-On Self Test Codes

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

3

84F1 Intelligent System Monitoring Forced Shutdown


84F2 Server Management Interface Failed No Yes Yes Yes Yes No

84F3 Baseboard Management Controller in Update Mode


84F4 Sensor Data Record Empty No Yes Yes Yes Yes No

84FF System Event Log Full No Yes Yes Yes Yes No

8500 DIMM1B, Memory Board A defective Yes Yes Yes No Yes No

8501 DIMM1A, Memory Board A defective Yes Yes Yes No Yes No

8502 DIMM2B, Memory Board A defective Yes Yes Yes No Yes No

8503 DIMM2A, Memory Board A defective Yes Yes Yes No Yes No

8504 DIMM1B, Memory Board B defective Yes Yes Yes No Yes No

8505 DIMM1A, Memory Board B defective Yes Yes Yes No Yes No

8506 DIMM2B, Memory Board B defective Yes Yes Yes No Yes No

8507 DIMM2A, Memory Board B defective Yes Yes Yes No Yes No

8508 DIMM1B, Memory Board C defective Yes Yes Yes No Yes No

8509 DIMM1A, Memory Board C defective Yes Yes Yes No Yes No

850A DIMM2B, Memory Board C defective Yes Yes Yes No Yes No

850B DIMM2A, Memory Board C defective Yes Yes Yes No Yes No

850C DIMM1B, Memory Board D defective Yes Yes Yes No Yes No

850D DIMM1A, Memory Board D defective Yes Yes Yes No Yes No

850E DIMM2B, Memory Board D defective Yes Yes Yes No Yes No

850F DIMM2A, Memory Board D defective Yes Yes Yes No Yes No


D2352 45

4 BMC Diagnostics and Beep Code Generation

The BMC may generate beep codes upon detection of the failure conditions. Codes that are common across platforms are listed below. Each digit in the code is represented by a sequence of beeps whose count is equal to the digit.

Code Reason for Beep

1-5-1-1 FRB3 failure (processor failure)

1-5-2-1 CPU: Empty slot

1-5-2-2 CPU: No processors

1-5-2-3 CPU: Configuration error (e.g., VID mismatch)

1-5-2-4 CPU: Configuration error (e.g., BSEL mismatch)

1-5-4-2 Power fault: DC power unexpectedly lost (power control failures)

1-5-4-3 Chipset control failure

1-5-4-4 Power control fault

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.k0

4

D2352 47

AbbreviationsASR&R

Automatic Server Reconfiguration and Restart

ATAAdvanced Technology Attachment

BIOSBasic Input-Output System

BMCBaseboard Management Controller

BSPBootstrap Processor

CDCompact Disk

CMOSComplementary Metal Oxide Semiconductor

CPUCentral Processing Unit

DIMMDual Inline Memory Module

ECCError Checking and Correcting

EFIExtensible Firmware Interface

FSBFront Side Bus

I/OInput/Output

48 D2352

Abbreviations

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.abk

IDEIntegrated Drive Electronics

IPInternet Protocol

IRQInterrupt Request

LANLocal Area Network

MACMedia Access Control

NICNetwork Interface Card

NMINon-Maskable Interrupt

NVRAMNon Volatile Random Access Memory

OSOperating System

PCIPeripheral Component Interconnect

POSTPower-ON Self Test

PXEPreboot Execution Environment

RAIDRedundant Arrays of Independent Disks

RAMRandom Access Memory

D2352 49

Abbreviations

RASReliability and Serviceability

RoMBRAID on Mother Board

SATASerial ATA (Advanced Technology Attachment)

SCSISmall Computer System Interface

SELSystem Event Log

SMServer Management

USBUniversal Serial Bus

VGAVideo Graphics Adapter

WOLWake On LAN

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.abk

D2352 51

IndexBBIOS Setup

accessing 7administrator password 35ASR&R 30BMC 33BMC diagnostics 45console redirection 32IDE controller 24keyboards commands 5LAN 25, 33mass storage 24memory configuration 16, 17, 20memory hot-plug 17memory test 16overview 8password on boot 35patrol scrub 16PCI 28POST error pause 10quiet boot 10RAID upgrade gap 17reserve rank for spare 20retest board memory 20saving changes 36SEL 34serial ports 27SM error halt 29sparing threshold 16system date 10system options 2system time 10USB 26user password 35video 26WOL 29

Eerror codes

POST 37

Mmemory configuration

max. compatibility 17max. performance 17mirror 17RAID 17sparing 22

Nnotational conventions 1

PPOST

error beep codes 37error codes 37, 41progress codes 38

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik

-Do

kum

ent

atio

n m

bH

20

05

Pfa

d: D

:\P

roje

kte\

2352

_BIO

S\D

2352

_BIO

S.s

ix

Comments on D2352 BIOS Setup Utilityfor PRIMERGY RX600 S3/TX600 S3

D2352

CommentsSuggestionsCorrections

✁

Submitted by

Fujitsu Siemens Computers GmbHUser Documentation81730 MunichGermany

Fax: (++49) 700 / 372 00000

email: [email protected]://manuals.fujitsu-siemens.com

http://manuals.fujitsu-siemens.com

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.nac

Comments on D2352 BIOS Setup Utilityfor PRIMERGY RX600 S3/TX600 S3

D2352

CommentsSuggestionsCorrections

✁

Submitted by

Fujitsu Siemens Computers GmbHUser Documentation81730 MunichGermany

Fax: (++49) 700 / 372 00000

email: [email protected]://manuals.fujitsu-siemens.com

http://manuals.fujitsu-siemens.com

© c

ogni

tas.

Ges

ells

chft

für

Tech

nik-

Dok

umen

tatio

n m

bH

20

05

Pfa

d: D

:\Pro

jekt

e\23

52_

BIO

S\D

2352

_B

IOS

.nac

Information on this document On April 1, 2009, Fujitsu became the sole owner of Fujitsu Siemens Compu-ters. This new subsidiary of Fujitsu has been renamed Fujitsu Technology So-lutions.

This document from the document archive refers to a product version which was released a considerable time ago or which is no longer marketed.

Please note that all company references and copyrights in this document have been legally transferred to Fujitsu Technology Solutions.

Contact and support addresses will now be offered by Fujitsu Technology So-lutions and have the format …@ts.fujitsu.com.

The Internet pages of Fujitsu Technology Solutions are available at http://ts.fujitsu.com/... and the user documentation at http://manuals.ts.fujitsu.com.

Copyright Fujitsu Technology Solutions, 2009

Hinweise zum vorliegenden Dokument Zum 1. April 2009 ist Fujitsu Siemens Computers in den alleinigen Besitz von Fujitsu übergegangen. Diese neue Tochtergesellschaft von Fujitsu trägt seit-dem den Namen Fujitsu Technology Solutions.

Das vorliegende Dokument aus dem Dokumentenarchiv bezieht sich auf eine bereits vor längerer Zeit freigegebene oder nicht mehr im Vertrieb befindliche Produktversion.

Bitte beachten Sie, dass alle Firmenbezüge und Copyrights im vorliegenden Dokument rechtlich auf Fujitsu Technology Solutions übergegangen sind.

Kontakt- und Supportadressen werden nun von Fujitsu Technology Solutions angeboten und haben die Form …@ts.fujitsu.com.

Die Internetseiten von Fujitsu Technology Solutions finden Sie unter http://de.ts.fujitsu.com/..., und unter http://manuals.ts.fujitsu.com finden Sie die Benutzerdokumentation.

Copyright Fujitsu Technology Solutions, 2009

d2352 bios setup utility for primergy rx600...

Documents