cylinder strength versus cube strength

26
Standing Committee on Concrete Technology Annual Concrete Seminar 2013 (18 April 2013) C C y y l l i i n n d d e e r r S S t t r r e e n n g g t t h h v v e e r r s s u u s s C C u u b b e e S S t t r r e e n n g g t t h h Ir. H D Wong, E/PWCL Standard & Testing Division Geotechnical Engineering Office Civil Engineering and Development Department 1

Upload: fsirfan

Post on 24-Nov-2015

122 views

Category:

Documents


10 download

DESCRIPTION

Compasrison betweeb Cube and CYLINDER

TRANSCRIPT

  • Standing Committee on Concrete Technology Annual Concrete Seminar 2013

    (18 April 2013)

    CCyylliinnddeerr SSttrreennggtthh vveerrssuuss CCuubbee SSttrreennggtthh

    Ir. H D Wong, E/PWCL Standard & Testing Division Geotechnical Engineering Office Civil Engineering and Development Department

    1

  • BackgroundBackground11

    OutlineOutline

    2

    DiscussionDiscussion44

    MethodologyMethodology22

    Analysis of test resultsAnalysis of test results33

    ConclusionConclusion55

  • 1. Background

    Design of public works civil engineering structures mainly makes reference to British Standards, such as: - BS 5400: Bridges - BS 8004: Foundations - BS 8007: Water retaining structures - BS 8110: Structural use of concrete

    The above standards were superseded by Eurocodes: BS EN 1990:2002+A1:2005, BS EN 1991-1-7:2006, BS EN 1992-1-1:2004, BS EN 1992-3:2006, BS EN 1997-1:2004, etc.

    3

  • 1. Background

    DEVB planned to migrate to Eurocodes for the design of public works civil engineering structures by 2015.

    In BS EN 1992-1-1:2004, Eurocode 2: Design of concrete structures, characteristic cylinder strength (fck) is used in most of the design formulae.

    In BS EN 206-1:2000: The characteristic strength at 28 days of 150 mm diameter by 300 mm cylinders or the characteristic strength at 28 days of 150 mm cubes are used for classification.

    4

  • BS EN 206-1, Table 7 gives the following correlation:

    5

  • In HK, 100 mm cubes are commonly used for determining the compressive strength of concrete as the maximum aggregate size used in concrete mixes is normally 20 mm.

    According to GS 2006, Cl.16.59(6): The size of the test cube shall be 100 mm for concrete with the maximum aggregate size not exceeding 20 mm and shall be 150 mm with the maximum aggregate size exceeding 20 mm.

    6

  • In order to investigate if the Eurocode relationship between cylinder strength and cube strength also holds for local concrete, DEVB proposed to carry out a study in late 2012.

    The aim is to study the correlation between 150 mm dia. by 300 mm cylinder strength and 100 mm cube strength for local concrete.

    7

  • 2. Methodology

    1. A study brief was written by WSD in consultation with CEDD and Prof. Kwan of HKU. Originally, it was intended to produce 50 sets of cylinder and cube samples for each grades of concrete ranging from 10 MPa to 95 MPa.

    2. After discussion with DEVB, Prof. Kwan of HKU volunteered to arrange the casting of samples and carry out the testing for the study.

    8

  • 2. Methodology

    With a view to shorten the study period and reduce the number of samples, Prof. Kwan modified the sampling requirements as following:

    Three sets of cylinder and cube samples from each of the grades of concrete ranging from 10 MPa to 95 MPa.

    100 mm Cube: 3 samples, two specimens for each sample.

    150 dia. x 300 mm cylinder: 3 samples, two specimens for each sample.

    9

  • Testing

    Between late 2012 and Jan. 2013, a total of 126 cubes and 126 cylinders were cast by concrete suppliers and two public works contracts.

    The PWCL was subsequently requested to take over the testing of concrete samples due to some difficulties in HKU in the testing of cylinders.

    By Feb. 2013, PWCL completed all the tests in accordance with CS1.

    10

  • 3. Analysis of test results

    (1) It is found that the actual cube test results ranged from about 10 MPa to 130 MPa. They were grouped into 12 strength bands ranging from 1020 MPa to 120-130 MPa.

    (2) According to GS2006: 1. The test result of a sample shall be the average compressive

    strengths of the two specimens tested at 28 days. 2. If the difference between the compressive strengths of two test

    cubes made from one sample of designed mix concrete exceeds 15% of the test result, the test result for that sample shall not be used to calculate the standard deviation.

    According to BS EN 206-1:2000 The test result should be discarded in case the range of the two compressive strengths is more than 15% of the average of the two compressive strengths.

    11

  • 12

    3. Analysis of test results

  • 3. Analysis of test results

    13

  • 3. Analysis of test results by HKU HKU carried out an analysis using regression technique based on the average values. The following best

    fitting curves were obtained:

    (i) 150 mm cylinder strength (y) to 100 mm cube strength (x) ratio is given by: y/x = 0.74 + 0.0008 x or

    14

    (ii) 150 mm cylinder strength (y) to 100 mm cube strength (x) ratio is given by: y/x = 0.75 + 0.0007 x

  • 3. Analysis of test results by PWCL

    Due to the small number of test specimens within each strength band, PWCL found that the standard deviation within each strength band is sometimes quite large especially at higher strength. A better curve fitting may be achieved if we separate the data into 2 zones, below 80 MPa and above 80 MPa.

    HKU suggests that:

    Concrete cube strength up to 80 MPa: a fixed coefficient 0.78

    Concrete cube strength higher than 80 MPa: a fixed coefficient 0.80

    15

  • 3. Analysis of test results by PWCL

    16

    PWCL obtained similar results based on the average values of two specimens

  • 3. Analysis of test results by PWCL

    In Eurocode, the design formulae mainly use characteristic cylinder strength.

    According to Cl.16.05 of GS Guidance Notes and BS EN 206, characteristic strength is the strength that 5% of samples fail to reach.

    Characteristic strength = Mean strength 1.64 x standard deviation.

    17

  • 18

    3. Analysis of test results by PWCL PWCL carried out regression analysis using on the characteristic value of strength grade

    and found the following relationship. (Test results with S.D. larger than 5 MPa were discarded.)

  • 3. Analysis of test results by PWCL Table 7 of BS EN 206-1

    19

  • 3. Analysis of test results by PWCL

    According to Special Project Report SPR 3/96, the

    28-day strength of 100 mm cubes is on average

    about 5% higher than that of the 150 mm cubes.

    Convert the 150 mm cube strength (in BS EN 206) into 100 mm cube strength by a factor of 1.05.

    20

  • 3. Analysis of test results by PWCL

    21

    Relationship between 150 mm dia. cylinders, 150 mm cubes and 100 mm cubes strength

  • 3. Analysis of test results by PWCL Best fitting curve from Table 7 of BS EN 206-1 modified for 100 mm cubes

    22

  • 4. Discussion

    Based on characteristic values, PWCL found an almost linear relationship of y=0.788x between 150 mm dia. cylinders (y) and 100 mm cubes (x) strength for concrete of grade 80 MPa or below.

    HKU proposed a linear relationship of y=0.78x for concrete grade 80 MPa or below.

    Based on BS EN 206 Table 7, a linear relationship of y=0.772x (modified for 100 mm cubes) is obtained for concrete of grade 80 MPa or below.

    From the above, it is noted that the difference between the cylinder/cube ratio in Eurocode and the results obtained from this study is only by a negligible margin of about 2%.

    However, the study is only based on 119 cylinders and 119 cubes. As the characteristic strength is affected by the standard deviation and this study is generally based on a set of 3 mean values obtained for each grade strength, PWCL proposed that the Eurocode relationship should be maintained for local concrete but modified for 100 mm cubes.

    23

  • 5. Conclusion

    The results of this study confirmed that the strength ratio (150 mm dia. cylinder vs. 100 mm cube) for local concrete is similar to that of Eurocode. The difference is about 2%.

    As this study is based on limited samples (119 cylinders and 119 cubes), it is proposed that the Eurocode relationship should be maintained for local concrete but modified for 100 mm cubes.

    24

  • The contribution from the following parties for their support to the study is gratefully acknowledged:

    - HKU - CPA - DSD - WSD

    25

  • End of presentation

    Thank you!

    26

    Structure BookmarksFigureStanding Committee on Concrete Technology. Standing Committee on Concrete Technology. Annual Concrete Seminar 2013. (18 April 2013)

    CCCCCCyylliinnddeerr SSttrreennggtthh vveerrssuuss CCuubbee SSttrreennggtthh.

    Ir. H D Wong, E/PWCL Standard & Testing Division Geotechnical Engineering Office Civil Engineering and Development Department BackgroundBackground11 OutlineOutline 2 DiscussionDiscussion44 MethodologyMethodology22 AnalysisoftestresultsAnalysis of test results33 ConclusionConclusion55 1. Background. Design of public works civil engineering structures mainly makes reference to British Standards, such as: -BS 5400: Bridges -BS 8004: Foundations -BS 8007: Water retaining structures -BS 8110: Structural use of concrete The above standards were superseded by Eurocodes: BS EN 1990:2002+A1:2005, BS EN 1991-1-7:2006, BS EN 1992-1-1:2004, BS EN 1992-3:2006, BS EN 1997-1:2004, etc. 1. Background. DEVB planned to migrate to Eurocodes for the design of public. works civil engineering structures by 2015.. In BS EN 1992-1-1:2004, Eurocode 2: Design of concrete. ck) is used in most of. the design formulae.. structures, characteristic cylinder strength (f

    In BS EN 206-1:2000:. The characteristic strength at 28 days of 150 mm diameter by. 300 mm cylinders or the characteristic strength at 28 days of. 150 mm cubes are used for classification.. BS EN 206-1, Table 7 gives the following correlation: 5 In HK, 100 mm cubes are commonly used for determining the compressive strength of concrete as the maximum aggregate size used in concrete mixes is normally 20 mm. According to GS 2006, Cl.16.59(6): The size of the test cube shall be 100 mm for concrete with the maximum aggregate size not exceeding 20 mm and shall be 150 mm with the maximum aggregate size exceeding 20 mm. In order to investigate if the Eurocode relationship between cylinder strength and cube strength also holds for local concrete, DEVB proposed to carry out a study in late 2012. The aim is to study the correlation between 150 mm dia. by 300 mm cylinder strength and 100 mm cube strength for local concrete. 2. Methodology. 1.. 1.. 1.. A study brief was written by WSD in consultation with CEDD and Prof. Kwan of HKU. Originally, it was intended to produce 50 sets of cylinder and cube samples for each grades of concrete ranging from 10 MPa to 95 MPa.

    2.. 2.. After discussion with DEVB, Prof. Kwan of HKU volunteered to arrange the casting of samples and carry out the testing for the study.

    2. Methodology. With a view to shorten the study period and reduce the number of samples, Prof. Kwan modified the sampling requirements as following: . . . Three sets of cylinder and cube samples from each of the grades of concrete ranging from 10 MPa to 95 MPa.

    . . 100 mm Cube: 3 samples, two specimens for each sample.

    . . 150 dia. x 300 mm cylinder: 3 samples, two specimens for each sample.

    Testing. Between late 2012 and Jan. 2013, a total of 126 cubes and 126 cylinders were cast by concrete suppliers and two public works contracts. The PWCL was subsequently requested to take over the testing of concrete samples due to some difficulties in HKU in the testing of cylinders. By Feb. 2013, PWCL completed all the tests in accordance with CS1. 3. Analysis of test results. (1) (1) (1) It is found that the actual cube test results ranged from about 10 MPa to 130 MPa. They were grouped into 12 strength bands ranging from 1020 MPa to 120-130 MPa.

    (2). (2). (2). According to GS2006:

    1.. 1.. 1.. The test result of a sample shall be the average compressive strengths of the two specimens tested at 28 days.

    2.. 2.. If the difference between the compressive strengths of two test cubes made from one sample of designed mix concrete exceeds 15% of the test result, the test result for that sample shall not be used to calculate the standard deviation.

    According to BS EN 206-1:2000 The test result should be discarded in case the range of the two compressive strengths is more than 15% of the average of the two compressive strengths. 3. Analysis of test results 3. Analysis of test results 13 3. Analysis of test results by HKU HKU carried out an analysis using regression technique based on the average values. The following best fitting curves were obtained: (i) 150 mm cylinder strength (y) to 100 mm cube strength (x) ratio is given by: y/x = 0.74 + 0.0008 x or 14 (ii) 150 mm cylinder strength (y) to 100 mm cube strength (x) ratio is given by: y/x = 0.75 + 0.0007 x 3. Analysis of test results by PWCL. Due to the small number of test specimens within each strength band, PWCL found that the standard deviation within each strength band is sometimes quite large especially at higher strength. A better curve fitting may be achieved if we separate the data into 2 zones, below 80 MPa and above 80 MPa. HKU suggests that: Concrete cube strength up to 80 MPa: a fixed coefficient 0.78 Concrete cube strength higher than 80 MPa: a fixed coefficient 0.80 3. Analysis of test results by PWCL 16 PWCL obtained similar results based on the average values of two specimens 3. Analysis of test results by PWCL. In Eurocode, the design formulae mainly use characteristic cylinder strength.. strength is the strength that 5% of samples fail to reach.. Characteristic strength = Mean strength 1.64 x standard deviation.. According to Cl.16.05 of GS Guidance Notes and BS EN 206, characteristic.

    3. Analysis of test results by PWCL PWCL carried out regression analysis using on the characteristic value of strength grade and found the following relationship. (Test results with S.D. larger than 5 MPa were discarded.) Figure3. Analysis of test results by PWCL Table 7 of BS EN 206-1 19 3. Analysis of test results by PWCL. According to Special Project Report SPR 3/96, the .28-day strength of 100 mm cubes is on average .about 5% higher than that of the 150 mm cubes..Convert the 150 mm cube strength (in BS EN 206) into 100 mm cube strength by a factor of 1.05. 3. Analysis of test results by PWCL 21 Relationship between 150 mm dia. cylinders, 150 mm cubes and 100 mm cubes strength 3. Analysis of test results by PWCL Best fitting curve from Table 7 of BS EN 206-1 modified for 100 mm cubes 22 4. Discussion. . . . Based on characteristic values, PWCL found an almost linear relationship of y=0.788x between 150 mm dia. cylinders (y) and 100 mm cubes (x) strength for concrete of grade 80 MPa or below.

    . . HKU proposed a linear relationship of y=0.78x for concrete grade 80 MPa or below.

    . . Based on BS EN 206 Table 7, a linear relationship of y=0.772x (modified for 100 mm cubes) is obtained for concrete of grade 80 MPa or below.

    . . From the above, it is noted that the difference between the cylinder/cube ratio in Eurocode and the results obtained from this study is only by a negligible margin of about 2%.

    . . . However, the study is only based on 119 cylinders and 119 cubes. As the characteristic strength is affected by the standard deviation and this study is generally based on a set of 3 mean values obtained for each grade strength, PWCL proposed that the Eurocode relationship should be maintained for local concrete but modified for 100 mm cubes.

    5. Conclusion.

    . . The results of this study confirmed that the strength ratio (150 mm dia. cylinder vs. 100 mm cube) for local concrete is similar to that of Eurocode. The difference is about 2%.

    . . As this study is based on limited samples (119 cylinders and 119 cubes), it is proposed that the Eurocode relationship should be maintained for local concrete but modified for 100 mm cubes.

    23. The contribution from the following parties for their support to the study is gratefully acknowledged: The contribution from the following parties for their support to the study is gratefully acknowledged: -HKU. -CPA. -DSD. -WSD. End of presentation Thank you! 26