cv - nasir muzaffar (chemical eng.)
TRANSCRIPT
NASIR MUZAFFAR KOTRIWALA
CAREER OBJECTIVE Secure a Process Engineer position or a Chemical Engineer position in a progressive organization, which offers challenging
and ample opportunities for growth and utilizes my technical, cognitive, communication and teamwork skills
EDUCATION
UNIVERSITY OF NOTTINGHAM 2008-2012
Undergraduate: MSci (Hons) – Integrated Master in Chemical Engineering
Awarded High Achievers Scholarship (25% Tuition fee waiver) by university
Third Year Research Project: “Techno-Economic Analysis of Jet Fuel Production from Biomass Gasification”
Final Year Design Project: “Production of Fatty Acids and Glycerine via Hydrolysis of Palm-Kernel Oil”
KARACHI GRAMMAR SCHOOL 2003-2007 GCE A-Levels: 2 A’s and 1 B (83.5 % HSC Equivalence) GCE O-Levels: 8 A’s and 3 B’s (81.0 % SSC Equivalence)
Awarded Breton Medal, Principal’s Medal by Karachi Grammar School for outstanding performance in O-Levels
WORK EXPERIENCE
PROCESS ENGINEER – ENGRO POLYMER & CHEMICALS LTD 17-Dec-13 to 9-July-15
Performed Daily Monitoring of PVC-I Plant Parameters and issued troubleshooting instructions to PVC Operations
Performed vessel entry and inspections at PVC plants during plant shutdowns and monthly PVC Grade Change outages
Prepared Process Engineering reports for Shutdown of PVC-I Plant and PVC-II Plant.
Worked on the following production expansion, product quality improvement and cost saving projects
Project - PVC-II Plant Debottlenecking Chiller Modification (Detailed Engineering & Commissioning Phase)
Performed Design of Suction Strainers, P&ID Development, What-If PHA Analysis, Preparation of Process Specs.
Specified Process DCS Alarms, Control Loop & provided Process Engineer support during project commissioning
Project - PVC-I Plant Debottlenecking Chiller Modification (Detailed Engineering & Commissioning Phase)
Performed Line Sizing, Mass & Energy Balance, P&ID Development, Rating and Design of Control Valves, Design of
Annubar Flowmeter, Design of Suction Strainers, Specifying DCS Panel Changes, Preparation of Process Specs
Participated in two-days long group Process Hazard Analysis exercise and prepared its recommendations report
Specified Process DCS Alarms, Interlocks & provided Process Engineer support during project commissioning
Liaised with Basic Design Consultant “INEOS”, representative of chiller vendor and pumps vendor.
Project - Design of 10 bar Steam Line for Dryer Inlet Air Heater Performed Mass & Energy Balance, Steam Line Sizing, Rating of Heat Exchanger, Rating and Design of Control Valves,
Design of Steam Orifice Plate and Flowmeter with DCS Density Compensation, Design of Steam Traps and Drip Legs, P&ID Development, What-If PHA Analysis.
Liaised with Design Consultant “Descon Integrated Projects Ltd” for Pipe Thermal Stress Study
House No. 191, 38 Street off Khayaban-e-
Ittehad, Phase 6, DHA, Karachi, Pakistan
+92-333-3957498, +92-334-2999669
pk.linkedin.com/in/nasirmuzaffar88
Mr. Muhammad Ali Ansari,
Manager - Technology Department ENGRO Polymer & Chemicals Ltd
Office No.: +92-21-34740021
Cell No.: +92-335-1225134
Project - Installation of Coriolis Mass Flowmeter at PVC-II Plant Performed P&ID Development, What-If Analysis, Specifying Cascade Control Loop, Preparation of Process Specs Specified DCS Formulae to calculate PVC Slurry Density and Concentration. Liaised with Instrument Engineering to verify
DCS results with field values. Liaised with Lab to arrange post-commissioning tests to verify DCS results
Project - Polished Water Makeup for Chilled Water Supply Tank
PW Line Sizing, P&ID Development, What-If PHA Analysis, Liaised with Water Treatment Consultant “Buckmann”
Project - Installation of Online Infrared Moisture Analyzer at PVC-II Plant Instrument Air Line Sizing, Rotameter Sizing, Specifying Cascade Control Loop, P&ID Development, What-If PHA Analysis
PROCESS ENGINEER - DESCON INTEGRATED PROJECTS LTD (f. JGC-DESCON) 17-Dec-12 to 9-Dec-13
Completed On-Job training of Hydraulics Design, Flare Relief Load, PSV Sizing, Separator Drums Sizing,
P&ID Development Philosophy based on Process Design Standards of Japanese Gasoline Corporation (JGC)
Performed Hydraulic Calculations for MOL Makori LPG Project & OMV Sawan Gas Field Processing Facility
Performed Restriction Orifice Sizing and updated PFDs, P&IDs, Cause & Effect Diagrams for United Energy Pakistan
INTERN (ENGINEERING SERVICES) – BRITISH PETROLEUM PAKISTAN 1-June-11 to 15-July-11
Verified the American Petroleum Institute 14C Design Standard checklist for Fired Heaters
Identified Health-Safety-Environment incidents caused by Engineering Services Department
Developed Excel based Fluid Mechanics spreadsheets to assist department engineers
INTERN (PROCESS ENGINEERING) - PAKISTAN PETROLEUM LTD 2-Aug-10 to 10-Sept-10
Performed Equipment Sizing Calculations based on GPSA Design Standard for Air Cooler, Compressor, Pumps,
Three-Phase Separator, Amines Absorber and Stripper towers of Hala Field Gas Processing system.
INDUSTRIAL AWARDS AND ACHIEVEMENTS Awarded “Corporate Excellence Award 2014” by Engro Polymer & Chemicals Ltd
TRAININGS AND CERTIFICATIONS Completed Training on “Dr. Edward de Bono’s ‘Six Thinking Hats’ – Tools For Parallel Thinking”
Obtained In-House Certification of Engro Polymer & Chemicals on DUPONT Process Safety and Risk Management
COMPUTATIONAL SKILLS PROFICIENCY MS Office: Adept at Word, Excel, Powerpoint, Visio
Chemical Process Simulators: Adept at Aspen HYSYS and Aspen Plus. Competent in SuperPro Designer
Hydraulics Softwares: Competent in Instrucal, Schlumberger PIPESIM, JGC Best Pipe, Neotec PIPEFLO, WELLFLO
LANGUAGE SKILLS PROFICIENCY Fluent at spoken and written English and Urdu
INTERESTS Reading Process Engineering Design Standards, magazines, books and online technical forums
INDUSTRIAL REFERENCES Mr. Syed Imran Bokhari,
Senior Process Engineer
Pakistan Petroleum Ltd
[email protected] [email protected]
Office No.: +92-21-111-568-568
Cell No.: +92-333-3630388
Mr. Zeeshan Zaki,
Assistant Manager - Process Design BYCO Petroleum Limited
Office No.: +92-21- 2752299
Cell No.: +92-304-2188433
Mr. Syed Muhammad Abu Fahad,
Process Engineer
ENGRO Polymer & Chemicals Ltd [email protected]
Office No.: +92-21-34740021
Cell No.: +92-332-2388056