craftsman scroll saw manual
TRANSCRIPT
ownersmanual
WARNING:
For your own SAFETY,read your OWNERS
MANUAL before operating
Scrol l Saw/Sander
CRAFTSMAN
MODEL NO. 15 INCH MOTORIZED
572.247202 SCROLL SAW/SANDER
assembly . operatifig . repair parts
Made lnU,S.A.
Part No. 380123 4 4/84 50M
Sears, Roebuck and Co., Chicago, Ill. 60684 U.S.A.
RULES FOR SAFE OPERATION1. Keep guards In place and in working order'
2. Remove adlustlng keys and wrenches' Form
habit of checking to see that keys and adjustingwrenches are removed f rom tool before turning it on'
3. Keep work area clean. Cluttered areas and
benches invite accidents.
4. Don't uge In dangerous envlronment. Don't
expose tools to rain. Don't use power tools in damp
or wet locations. Don't use powertools in f lammable
or explosive atmospheres. Avoid chemical or
corrosive environments. Keep work area well lit'
5. Keep chlldren away. All visitors should be kept a
safe distance from work area'
6. Make workshop kld'proof with padlocks, master
switches, or by removing starter keys'
7. Don't force tool. lt will do the iob better and saferat the rate for which it was designed.
8. Use rlght tool. Don't force tool or attachment to
do a job it was not designed for.
9. Wear propel apparel. No loose clothing, gloves,necktieq rings, bracelets, or other jewelry to get
caught in moving parts' Nonslip footwear is
recommended. Wear protective hair covering to
contain long hair.
10. Always use safety glaeses. Also use face or dust
mask if cutting operating is dusty. Everyday
eyeglasses only have impact resistant lenses, they
are not safety glasses.
11. Secure work. Use clamps or a vise to hold workwhen practical. l t 's safer than using your hand and it
frees both hands to operate tool'
12. Don't overreach. Keep proper footing and
balance at al l t imes.
\J
13. Maintain tools with care. Keep tools sharp and
clean for best and safest performance' Follow
instructions for lubricating and changing
accessories.
14. Disconnect tools before servicing; when chang-
ing accessories such as blades, bits, cutters' etc'
15. Reduce the risk ol unintentional starting' Make
sure switch is in "OFF" posit ion before plugging in'
16. Use recommended accessories' Consult the
owner's manual for recommended accessories' The
use of improper accessories may cause risk of injury
to persons.
17. Never stand on tool. Serious injury could occur
if the tool is t ipped or i f the cutt ing tool is
uni ntentionallY contacted'
18. Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should be
careful ly checked to assure that i t wil l operateproperly and perform its intended function - check
for al ignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other
conditions that may atfect its operation' 'A guard or V-'other part that is damaged should be properly
repaired or rePlaced.
19. Dlrection of feed. Feed work into a blade or
cutter against the direction of rotation of the blade or
cutter onlY.
20. Never leave tool runnlng unattended' Turn
power off. Don't leave tool until it comes to a
complete stoP.
21. Be alert. Don't use power tools when tired or
fatigued. Don't use power tools after taking drugs'
alcohol or medications.
WEAR YOUR
Y ̂01[$st$The operation of any power tool can result in foreign objects
being thrown into the eyes, which can result in severe eye
damage. Always wear safety glasses or eye shields before
comm-encing power tool operation' We recommend Wide Vision
Safety Mask for use over spectacles, or standard satety glasses
. . . avai lable at Sears retai l or catalog stores'
For the most pleasure from your Scroll Saw/ Sanderfollow these instructions carefully:The Cratbman Scroll Saw is a multi-purpose workshop. By con-necting dif ferent attachments to the power take-off, the unitis converted from the basic scrol l saw to a grinder, sander,buff ing wheel, brush wheel, and a f lexible shaft machine. Thenyou are able not only to saw, but dri l l , gr ind, pol ish, rout,sharpen, sand, buff, carve, engrave and perform many otherhobby, home or shop operations. Use with 247' l accessory pack.
DO NOT OPERATE MACHINE WITHOUT ATTACHING TABLE.CAUTION: DISCONNECT PLUG FROM OUTLET.
ATTACHING SAW TABLE
1. Remove b lade guard - push one s ide in - wh i le pu l l ing onopposite side.
2. Push lever (A) down as i l lustrated - to remove blade.
3. Loosen bottom wing nut and sl ide table bracket (C) upwardaboul 11/z inches from bottom, and t ighten.
4. Remove top wing nut (B) and washer - leaving bolt in posi-t ion - and attach table by insert ing bolt through curvedslot (D) with hole at top posit ioned over pin.
5. Place washer on outside of bracket and t ighten wing nut.6. Loosen bottom wing nut - let sl ide bracket (C) drop into
original posit ion and t ighten wing nut.
7. Replace saw blade (be sure teeth are point ing downward)by insert ing blade into lower blade holder - then pushlever down and insert into upper blade holder.
8. Replace blade guard with side pins on each side of blade- pushing one side in and then the other - as in step 1.
Motor-Runs on 110-120 Volt, 60 cycle, AC, and produces 3450R.P.M. l t i s equ ipped w i th two sea led ba l l bear ings . No o i l ingis needed. Charac ter is t i ca l l y , th is shaded po le - type motor runsa bit warm. However, overheating wil l not affect overal l op-era t ion .
Oil ing-A few drops ot ordinary motor oi l should occasional lybe placed on the connecting l ink bean-ng through the FoTe onthe le f t s ide o f the f rame. For o i l ing , lay un i t on i t s s ide , UseSA30 motor oi l .
Cult ing Capacity-Soft wood up to 13/q" and hardwood up to% " in th ickness can be cu t . FEED WOOD SLOWLY. DO NOTFORCE. When cutt ing wood over 11A" , the blade guard must beremoved. To remove guard , s imp ly pu l l ou t ends o f guard wherethey enter the fram?. When through sawing . . . BE SURE TOREPLACE THE FINGER GUARD,
Sawing Meta ls*Saw a luminum to 7a" th ick , copper to 18gauge, and s tee l to 1 /16" th ick . When sawing meta l , i t i s im-por tan t to ho ld the work f i rm ly on the tab le , use o i l as alubricant, and feed the work with a slow, steady pressure. Donot force i t .
Blade Guard-The blade guard is considered one of the safest.I t functions also as a hold-down.
lncreasing Blade Life-When blade teeth become dul l in onespot simply loosen the lower wing nut located iust beneath thesaw table, and raise the table to a section of new, unused teeth.Ti l t ing Table-For angle sawing, the table can be t i l ted ineither direct ion. Loosen the top wing nut located iust beneaththe saw tab le , and t i l t to the des i red ang le fo l low ing the ca l i -brated scale.Making In3ide Culs-First, use the t lexible shaft to dri l l a3/16" hole in the area to be sawed out. Then, remove theblade, thread i t through the hole, and return i t to the cutt ingposit ion.
Hofding Scroll Saw In Place-On a tairly smooth table orbench, the rubber suc t ion cups w i l l keep i t t rom s l id ing . Other -wise, set the machine on a 1/2 " thick rubber pad, such as ahouseho ld knee l ing pad or typewr i te r cush ion .
GROUNDING INSTRUCTIONSln the event ol a malf unction or breakdown, grounding provides a pathof least resistance for electr ic current to reduce the r isk of electr icshock. This tool is equipped with an electr ic cord having anequ ipment -ground ing conductor and a ground ing p lug . The p lugmust be plugged into a matching outlet that is properly instal led andgrounded in accordance with al l local codes and ordinances.
BLAOE lA)HOLDEB ' '
IIFORTAITTEETH
---\
MUST POINT
DOWNWARD
extending trom the adapter must be connected to a permanent groundsucn as a outlet box
HOL€
INaow
Do not modify the plug provided - i f i t wi l l not f i t the outlet, have theproper outlet instal led by a qual i f ied electr ician.lmproper connection of the equipment-grounding conductor canresult in a r isk of electr ic shock. The conductor withlnsulat ion havinoan outer surface that is green with or without yel low str ipes is th6equipment-grounding conductor. l f repair or replacement of theelectr ic cord or plug is necessary, do not connect the equipment-ground ing conductor to a l i ve te rmina l .Check w i th a qua l i f ied e lec t r i c ian or serv iceman i f the qround inqinstructions ard not corhpletely understood, or i f in Oo"uUt as t5whether the tool is properly grounded.Use only 3-wire extension cords that have 3-prong grounding plugsanil3-pole receplacles that accept the toot's plug.Repa i r o r rep lace damaged or worn cord immedia te ly .This tool is intended for use on a circuit that has an outlet that looksl i ke the one i l lus t ra ted in F igure A. The too l has a g round ing p lug tha tlooks l i ke the p lug i l l us t ra ted in F igure A. A temporary adapter , wh ichlooks l ike the adapter i l lustrated in Figures B and C, may be used toconnect this plug to a 2-pole receptacle as shown in Figure B i f aproperly grounded outlet is not avai lable. The temporary adaptershould be used only unti l a properly grounded outlet can be instal ledby a qual i f ied electr ician. The green-colored r igid ear, lug, etc.
The operation of any power tool can result in foreign obiects beingthrown into the eyes, which can result in severe eye damage. Alwayswear safety glasses or eye shields before commencing power tooloperatron.NOTE: The adapter_i l lustrated is not al lowed in Canada by theCanadian Electr ical Code.The use of any extension cord wil l cause some loss of power. To keepthas to a minimum and to prevent overheating and motor burn-out, usethe table below to determine the minimum wire size (A.W.G")extension cord. Al l cords should be 3-wire grounded.Extension GordsUse only three-wire extension cords that have three-prong groundingVpe. plugs and. three-pole receptacles that accept the tool plug.Replace or repair damaged or worn cord immediately.
Exiension Cord Length50 ft. or less
100 ft . or less
Wire Size A.W.G.N o . 1 6N o . 1 4
3
--8UDE
\ro rrro *on^,uoSAW LIFT BLADE GUARO
FROM THIS POSITION
l--nnl Inn.]l \ - ! - / l l \ . / / l
\ - lA I l - -o ' I"-F [?-J:aa?i'r'""r=l @ I
GROUNDING PIN
F I G U R E A
TEMPORARYADAPTEF
a>r FTGURE B
\_(s-X cRouNDrNG
l!) - MEANS
F I G U R E C
{@nAttaching Accessories-The round extension onthe motor housing is thepower take-off for drivingthe sander,buff ing wheel,and f lexible shaft .These are mounted onspecial adapters which fitinto the power take-off.BE SURE THE MOTOR ISTURNED OFF. Line uppin in the motor shaft withthe slot in the adapter andpress forward as far as it
It 's a scroll saw-Handles everything from small scrollwork to full size furniture work. Cuts up to standard 2 x4's, 18 ga. copper, 1/4" aluminum and steel.
It 's a Disc Sander-For shaping small pieces, sandingrough edges, trueing up uneven surfaces. Three discgri ts permit f ine, medium, coarse sanding.wi l l go. Turn the wheel s lowly unt i l the adapter set screw
comes into view. Then t ighten l ight ly. This screw doesnot dr ive the shaft , i t merely minimizes vibrat ion and
Becommendecl Accessories#2471-Accessory Kit.; 26877 -Fine Tooth blades.:*26878-Coarse Tooth bl ades.
CUT LONG LENGTHS
SAND BEVETS CONTOUR
e2544-4" Assorted aluminum oxide Sanding Discs.
For more pleasure and versatility add kit 2471Altaching Flexible Shalt-Be sure MOTOR lS RUNNINGbefore the cable is engaged. DO NOT REMOVE ORLOOSEN SCREW IN NYLON COUPLING. Inser t theblack ny lon coupl ing over the power take-of f . Push thecoupl ing on as far as i t wi l l go, and hold in p lace byturning the coupling counterclockwise. To prevent thecable f rom becoming d isconnected whi le the machine isrunning, s imply grasp the handpiece and twist the cableone-half turn counterclockwise.
CHUGK-Chuck consists of a chuck cap and collet. To changeor insert bits use the two chuck wrenches furnished. Slip theshort end of the bent wrench over flats on the shaft and holdthe long portion ot this wrench against the handpiece withone hand. With the shaft secured by the bent wrench, use thestraight wrench to loosen or t ighten the chuck cap. See il lustr-ration. With the chuck cap loose, an accessory should beinserted as deeply as possible to avoid wobble during use.Now, tighten chuck cap - evold excertlye tlghtlng.
BENTWRENCH
COLLETS-Four col lets are avai lable for your tool. Each hasa dif ferent hole diameter in order to accept various accessoryshank and dri l l sizes. To insert a dif ferent col let, fol low chuckloosening instruct ions. After chuck cap is loosened, continueto unscrew unti l i t comes off. Remove col let ( i t should dropout eas i l y by t ipp ing the too l ) . Inser t the co l le t des i red andreplace chuck cap. Choose the r ight col let for the accessoryshank or dri l l size. Never try to force a larger diameter shankor d r i l l i n to a smal le r s ize co l le t open ing .
FLEXIBLE SHAFT PROVIDES EXTRA VERSATILITY
DRILLING ROUTING
DEBURRING G R I N D I N G
SHARPENING CARVING
For best results, use the flexible shaft with a delicatetouch. To prevent stall ing the motor, press the tooll ightly against the work, and never force the tool beyondits capacity.
taIII
I
qw4
CodeNo.
ParlNo. Description
445 1 05 Guard
99087 1 Bow Pivot Nuts 10-32 Hex Local Hdwe. (4)
3 4451 30 Lef t F rame S ide (Smal l Ho le )
A 990885 Hardware16 Screws and 4 Washers
5 990887 G u i d e B u s h i n g 1 P r ( 4 P r R e q ' d . )
6 445132 Frame Cover. Lower
7 990874 Connect ing L ink (Comple te)
8 990764 Bow Arm
I 990765 Bow Arm w/Wrist Pin
1 0 445063 Spr ing
1 1 990877 Switch Assembly
445129 Righ t F rame S ide (La rge Ho le )
'13 990878 Bow Pivot Screw.10-32 x 1-3/4 Local Hdwe. (4)
1 4 990884 Motor Mount Screws (2 Lower, 1 Upper)'15 445073 Base w/o Feet
CodeNo.
ParlNo. Descript ion
.16 990880 Suct ion Cups Long & 2 Screws
1 7 99088 1 Suct ion Cups Shor t & 2 Screws
1B 990883 Hous ing Ex tens ion & Screws
1 9 404038 Cord
20 9901 49 Tab le S l ide Bracket Assemblv
445030 Tab le w/Ouadrant
22 9901 85 Motor Comple te w/Hous ing & Cord
23 990888 Screw #10 Sheet Meta l5 /8 Long Loca l Hdwe. (5 )
4211 Adapter Assembly Ior 4" Pad
25 4214 4" Rubber Back ing Pad (Use w i th 4211)
t o 26877 3 in . P in Type (F ine) B lade
26878 3 in . P in Type (Coarse) B lade
3801 23 Owners Manua l (no t i l l us t ra ted)
27 284000 Cab le C lamp
28 445044 Cord Stra in Rel ie l
29 445131 Frame Cover, Upper
5
ownersmanual
MODEL NO.572.247202
SearsSERVICE
is atYOUR
SEFVICE
How to ORDER Repair Parts
The Model Number will be found on a plate attached to your Sawat the rear of the base. Always mention the Model Number whenrequesting service or repair parts.
All parts l isted herein may be ordered through SEARS,ROEBUCK AND CO. When ordering parts by mail, sel l ing priceswil l be furnished on request or parts wil l be shipped at prevail ingprices and you wil l be bi l led accordingly.
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOL-LOWING INFORMATION AS SHOWN IN THIS LIST,
The PART NUMBER
The PART DESCRIPTION
The MODEL NUMBER 572.247202
The NAME OF ITEM-SCROLL SAW/SANDER
1 .
2.
3.
4. v
FULL ONE YEAR WARRANTY ONCRAFTSMAN SCROLL-SAW SANDER
lf this Craftsman Scroll-Saw/Sander fails to give complete satistaction within one year from thedate of purchase, return it to the nearest Sears store throughout the Unit€d States, and Sears willreplace it, free of charge.
lf ihis Scroll-Saw/Sander is used for commercial or rental purposes, this warranty applies for only90 days from the date ot purchase.
This warranty gives you specif ic legal rights, and you may also have other rights which vary f romstate to state.
Sears, Roebuck and Co.BSC 41-3Sears TowerChicago, lL 60684
Your Sears merchandise has added value when you considerthat Sears has service units nationwide staffed with Searst ra ined technic ians . professional technic ians speci f ica l lytrained on Sears Products, having the parts, tools andequipment to insure that we meet our p ledge to you . . . . weserv ice what we sel l .
Sears, Roebuck and Co., Chicago, Ill. 60684 U.S.A.Made inU.S.A.
6
ERRFTS}IRJI.
IMPOKTANTMAINTDNANCE INFOKMATION
Your Craf tsman@ Scro l l Saw/Sander was thor-oughly inspected to r ig id s tandards pr ior to leav ingthe manufacturer 's factory and should g ive youmany years of satisfactory service.
Occasional ly , when the Craf tsman@ Scro l l Saw/Sander is removed f rom i ts car ton and the tab leat tached, the user wi l l not ice that the b lade doesnot appear to be perpendicu lar to the tab le sur face(F igu re 1 ) .
Before attempting to correct this condit ion, f irstcheck to see that the table is in i ts horizontal or zerodegree (0") posit ion. Use a square or other r ight an-gle device (a piece of paper wilt suffice) to check theblade position relative to the table surface (Figure 2).l f the blade is not perpendicular to the table, simplypush the upper arm of the saw frame in the directionthat wil l correct the blade al ignment (Figure 3).
Handling the saw by holding the upper arm of thesaw frame (Figure 4) can also cause the saw blade to
ti l t from the true vert ical posit ion. This is not an unu-sual condit ion and can be easily corrected by, again,applying sl ight pressure to the upper arm of the sawframe in the direction that wil l correct the al ignment(F igure 3) .
l f the user avoids the natural tendency to use theupper arm of the frame as a handle when l i f t ing ormoving the saw, there should be no further need torealign the blade. Figure 5 shows the proper way topick up the Scrol l Saw.
Before deciding on any adjustment, i t is recom-mended that you operate the saw and make sometrial cuts so that you can experience scrol l cutt ing.Be sure to check the mounting of the saw blade inthe blade holder prior to cutt ing. Generally the bladeis mounted so that the teeth are facing front. How-ever, the blade can be mounted with the teeth facingthe side. Always have the saw teeth oriented to adownward cut.
i'll i
i
Figure 1 Figure 2
Figure 3
Form No. 380226 21-11 /83-ZO
Figure 4 Figure 5