costco high wire playset assembly instructions · 2020. 5. 8. · #27a top canopy support 1 #102...

52011

Costco High WireAssembly Instruc ons & Owner's Manual

Important! Read this manual completely through before assembly and use.Consumer assistance Toll free – If you need to order replacement parts or have any questions or concerns about your Kid’s Creations product; Call 1-800-437-0784.

Warning: Installation over a hard surface such as concrete, asphalt or packed earth may result in serious injury or death from falls

Copyright Kids Creations, L.L.C., Garnett, Kansas

2254-CA

High Wire - Parts List

PALLET QTY

3144 5' Rock wall 13120 Deck Panel 83130 Ladder 1 .

#8 Deck Support 4#27A Top Canopy Support 1#102 Wood canopy Face Board 4

#25 Tower End Brace 5#28 Canopy Upright 1

#4 Right Hand Brace 3#5 Left Hand Brace 3#6 Handrail Support Post 3

#14 Deck Facer Board 51liardnaH05#

#23 A-frame Block 1#101 Wood Roof Slat 22

#104 Canopy Facer Board 2#52 Beam Connecting Post 1

Swings - Green 3Rocks (12) 1Safety Handles Pair 2Steering Wheel 1

1epocseleTTrapeze 1

+ Hardware

#70 Balcony Deck Supports 2#81 Balcony Facer Board 2#95 Slide Face Mount 1#96 Slide Face Mount 1#97 Slide Face Mount 1

#2 Tower Base Board 1

#3 Tower Base Board 2#7 Tower Facer Board 5#9 Deck Board 5

3122 Small Rails 63124 Large Rails 4

2CliardnaH52133134 45 Degree Ladder 13132 3 Rung Ladder 1

BUNDLE #1 QTY

#46 Swing Beam 1 #1 Tower Leg 4

A

s

BUNDLE #2

#26 Wood Canopy Support 2#22 A-frame Support 1#24 A-frame Leg 2#80 Canopy Upright 1

BUNDLE #3

#34 Tower Leg 4s#51 Tower Base Board 2

SLIDE BUNDLES

1edilSebuT

14' Green Slide 114' Blue Slide 1

BOLT BOX

11" x 1/2" Bolt 69" x 1/2" Bolt 17" x 1/2" Bolt 805" x 1/2" Bolt 343 1/2" x 1/2" Bolt 8

921stuN"2/11/2" Washers 129

513swercS"34" Lag Screws 10Slide Screws 6Star Head Driver 1Snap Hooks 87" x 3/8" Carriage Bolt 163/8" Flat Washer 303/8" Lock Nut 16

3/8" Lock Washer

1/2" Lock Washer

3/8" Torque Washer 16Swing Hanger Spring Clips (6 Per Bag)

8 2 10

129

1/4" x 1” Flat WasherNameplate

6 1

NOTE :�ALL�BOLTS�GET�A�WASHER,�LOCK�WASHER,�AND�A�NUTIN�THIS�ORDER.

Prior to construction:

� Follow each assembly instruction in this booklet very carefully and thoroughly.

� Open all packages and parts bags and lay all parts that look the same together.

� Before using play center, review all maintenance and safety play tips and inspect for proper and complete assembly.

� Wear safety glasses at all times during assembly. � Configuration shown may be altered according to layout desired and

area placed � Note: Bolts were designed to be very snug when inserted into pre-drilled

holes. Use of a hammer will be necessary.

Parts needed for step 1

(4) Part #34 119 ¾” 4x4

(2) Part #26A 10’ 9” 4x4

(2) Part #8 4’ 10” 4x6

1. Using 7” bolts, connect part #8 to 2 of part #34’s with counter

sink on part #34 facing inward. Counter sink on part #8 should be facing up.

2. Using 7” bolts, connect part #26A to 2 parts #34’s. Note: Locate

counter sinks on part #26A – they should be facing DOWN.

3. Tighten all connec ons and repeat for opposite side.

Place #8 - in the upper holes on part #34.

#26A

#34

#8

NOTE: Place all bolts so they have the nut in the counter sink part of the board, so they will not stick out and harm anyone.

CountersinkInward

Countersink up

CountersinkDirec ons

Parts�needed�for�step�2

(1)�Part�#28��6'�5"��4x4

1.�Connect�part�#28��as�shown�with�7"�bolts.

#28


(1)�Part�#80��8'5"��4x4

1.�Connect�part�#80�to�other�side�as�shown�with�7"�bolts.

#80

80

28


(2)�Part�#7��5'�6"��2x6

1.�Do�not�tighten�bolts.2.�Stand�up�both�tower�frames�made�in�earlier�steps�2�and�3.�Note:�Part�#8��(4x6)�on�both�tower�legs�should�be�on�the�inside�of�the�tower.3.�Using�5"�bolts,�connect�part�#7�to�both�towers.

#80

#28#7

#7


(1)�Part�#3��4'10"��2x6(1)�Part�#4��2'2"��4x4��(1)�Part�#5��2'2"��4x4

1.�Facing�the�2x6�(part�#7)�using�5"�and�3�1/2"�bolts,�connect�part�#4�to��the�right�hand�side�and�connect�part�#5�to�the�left�hand�side.�2.�Using�3"�screws�connect�part�#3�to�the�side�of�tower�with�part�#28.3.�Using�a�level�and�square,�square�up�swing�set�and�tighten�all�bolts.

#4

#5

#3


(1)�Part�#8��4'10"��4x6

1.�Using�7"�bolts�connect�part�#8�to�the�tower�as�shown.��Note:�The�counter�sink�on�part�#8�should�face�out.

#8

These two�bolts�will�be�replaced�by�11"�bolts�in�a�later�step.

Note:

Note:

#1

#8

#50

CountersinkDirec ons

Parts�needd�for�step�8

(1)�Part�#3��4'10"��2x6(1)�Part�#7��5'6"��2x6(2)�Part�#51��131�1/2"��2x6

1.��Using�5"�bolts�connect�part�#7�to�main�tower�then�stand�up��end�frame�and�connect�to�other�end�of�part�#7.2.�Using�5"�bolts�attach�parts�#51�to�tower�legs�as�shown.3.�Using�3"�screws�attach�part�#3�as�shown.

#51

#3#51

#7

Part�needed�in�step�9

(1)�Part�#4��2'2"��4x4(2)�Part�#5��2'2"��4x4

1.�Facing�the�2x6�(part�#7)�connect�part�#4�to�the�right�hand�side�using��5"�and�3�1/2"�bolts�connect�#5�to�the�left�hand�slide.2.�Connect�rockwall�to�tower,�using�11"�bolts.�The�existing�lower�7"��bolts�placed�in�the�#8�will�be�removed�and�replaced�with�the�11"�bolts.�3. To attach rocks, place rocks in random pattern by using the 1-1/2" screw in the small hole of the rock to place the rock.4. After you have connected the rocks to the rock wall with the little screw, rotate the rock where you want it. Use the 2" screw and washer in the large hole of the rock to set the rock in place.

#5

#4


(2)�Part�#9��4'11"��2x6

1.�Place�deck�boards�on�top�of�4x6�(part�#8)�and�place�#9's�on�the�outside.2.�Using�3"screws;�screw�each�2x6�deck�board�into�the�4x6�below.��Use�2�screws�on�each�end�of�deck�board.

#9

#9

Deck panels

Part�needed�for�step�11

(2)�Part�#9��4'11"��2x6

1.�Attach�decking�in�same�manner�as�step�10�using�3"�screws.

#9

#9

Deck panels

Part�needed�for�step�12

1.�Attach�small�ladder�as�shown�using�3"�screws.

Part�needed�in�step�13

(4)�Part�#25��6'3"��4x4

1.�Connect�2�part�#25�to�part�#34�on�upper�tower�using�7"�bolts.2.�Connect�2�part�#25�to�parts�#1�and�#34�on�lower�tower�using�7"�bolts.

#25

#25#25

#25


(2)�Part�#6��2'10�1/2"��4x4

Note:�Refer�to�the�next�page�for�proper�placement�of�part�#6.

1.�Attach�#6�using�7"�bolt�on�top.�Screw�up�through�the�deck��panel�using�3"�screws�on�bottom.

#6

#6

Step�15

1.�Each�part�#25�has�two�drilled�holes�near�the�center�of�the�board.��Using�the�correct�hole�placement,�(depending�upon��your�accessory�options)�bolt�the�#6�to�the�#25.

Opeining�for�small��rail,�slide,�drawbridge or�monkey�bars� 24"

Opeining�for�small��rail,�slide,�drawbridge or�monkey�bars� 24"

Opening�for�large�rail�or�ladder�32"

#25

#25

#6

#6


(1)��Part�#52��3'8�1/2"��4x4

1.�Attach�#52�using�7"�bolts.�The�swing�beam�will�attach�to�part�#52.��Note:�Countersinks�on�part�#52�will�face�away�from�the�hole��on�the�top�of�part�#50�where�it�is�attached.

#52

#50


1.�Attach�ladder�as�shown�using�7"��bolts.


(5)�Part�#14��1'11�3/4"��2x4

1.�Attach�part�#14's�using�3"�screws.�Handrails�will�set�on�the�part�#14's,��so�place�them�flush�with�the�deck�boards.

#14

#14

#14


1.�Attach�handrails�to�lower�tower�as�shown�using�3"�screws.

small�rails

small�rail


1.�Attach�handrails�to�upper�tower�using�3"�screws.2.�Place�small�rail�in�opeing�between�5'�and�7'�decks.

Large�rail

"C"�handrails

Small rail


1.�Attach�small�handrail�as�shown�using�3"�screws.

Small�rails


(2) Part #1 7'11 3/4" 4x4

(1) Part #7 5'6" 2x6

(1) Part #25 6'3" 4x4

1. Using 7" bolts a ach part #25 to 2 part #1's. Note: Counter sinks

on parts #1 should be facing up.

2. A ach part # 7 to parts #1 using 5" bolts.

#7

#25

#1

Countersinks UP

Countersinks DOWN


��(2)�Part�#70��40�1/2"��4x6

1.�Attach�2�part�#70�with�2�part�#1�as�shown�using�7"�bolts. �Note: The��counter�sinks�on�part�#70�should�face�in�towards�each�other.2.�Stand�up�frame�as�shown�and�attach�parts�#70�to�the�2�part�#34's�using��7"�bolts�on�the�outside�and�11"�bolts�on�the�inside.

11"�bolts�go�here

#70


��(1)�Part�#4��2'2"��4x4��(1)�Part�#5��2'2"��4x4

1.�Facing�the�2x6�(part�#7)�using�5"�and�3�1/2"�bolts,�attach�part�#4�to�the�right��hand�side�and�attach�part�#5�to�the�left�hand�side�as�shown.

#4

#5


��(1)�Part�#9��4'11"��2x6

1.�Using�3"�screws�attach�both�deck�sections�and�part�#9.

Deck�panels

#9


��(1)�Part�#7��5'6"��2x6

1.�Attach�part�#7�as�shown�using�3"�screws.

#7


1.�Attach�3�rung�ladder�as�shown�using�3"�screws.


��(1)�Part�#6��2'10�1/2"��4x4��(2)�Part�#81��2'7�7/8"��2x4

1.�Attach�#6�using�7"�bolt�on�top.�Screw�up�through�the�deck�panel�using��3"�screws�on�bottom.2.�Attach�part�#81's�using�3"�screws.�Note: Rails�will�sit�on�the�#81's,�so�they�need��to�be�mounted�flush�with�the�deck�panels.

#6

#81

#81


1.�Attach�rails�as�shown�using�3"�screws.

Large�

Small�rail

Large�rail


(2)�Part�24��9'5"��4x4(1)�Part�23��15�5/8"��4x6(1)�Part�22��8'�8�7/8"��4x4

1.�Using��7"�bolts�connect�both�part�#24's�to�part�#23�as�shown.��Note:�Countersink�on�part�#23�must�be�on�the�bottom.2.�Using�7"�bolts�connect�part�#22�to�both�part�#24's.

#24

#23

#22

Step�31

1.�Attach�swing�beam�as�shown�using�11"�bolt.

Step 32

1. Attach end of swing beam to parts #50 and #52 using 9" and 7" bolts.

2. Attach part #27 on top of parts #80 and #28 using 4" lag screw.

Hint: Start lags with a hammer, do not over tighten.

#27#52

#50

9" bolt

#95

#96

#97

23”-1/2

30-1/2”

3” Screws Flush

Flush

Two at each location.

Center Tube Slide Face Plate in opening.#95

#96

#97

8” minimum

TRAPEZE / SWING INSTALL

54” minimum

2435

Attaching rocks to rock wall

1. Place rocks to rock wall in random pattern and mark hole positions. Pre‐drill marked holes

using 5/16" drill bit. Pound T‐Nut in back of rock wall.

2. Install Rock using 1/4 x 2" Hex bolt, lock washer, and flat washer.

Slide installation

Place slide on deck 3" from the edge and secure using three 1‐1/2" slide screws and

Fender washers through the top of the slide and screw tightly into the decking.

3"


(4) Part #102 2x4 5' 1 1/8"

1. Attach part #102 as shown using 3" screws.

#102

#102

26A


(1) Part #27A 2x4 5' 6"

1. Attach part #27 to the top of #28 using 4" x 3/8" lag bolt.

#27A


(2) Part #104 2x4 39 1/2"

1. Attach part #104 using 3" screws.

#104

#104


(22) Part #101 2x6 6' 2"

1. Attach part #101, starting at top of the roof using 3" screws. Work

downward centering boards, so the overhang is about 4" on both sides

of the #102. HINT: Temporarily screw a part #101 at the bottom for the

other #101's to rest on while you attach screws.

#101

5/16” X 1” BOLT W/WASHERS AND LOCK NUT

5/16” X 3/4” BOLT W/WASHER

2 SECTIONS WITH OVER-LAPPING FLANGES

3 SECTIONS WITHOUT OVERLAPPING FLANGES

*** THIS PRODUCT IS INTENDED FOR RESIDENTIAL USE ONLY.***

3-1/2” LAG SCREW W/WASHER

STEP 1: ATTACHING ENTRANCE TUBE TO THE CORNER POSTS

Take the FACE PLATE ENTRY piece labeled #1 and place it flush to the corner posts, so that the bottom of the large circular opening is flush to the TOP of the deck boards. Fasten the FACE PLATE ENTRY to the corner posts with 3-1/2” lag screws and 3/8” washers in all the holes. **NOTE: YOU MAY HAVE TO DRIVE THE LAG SCREWS IN AT AN ANGLE TO CONTACT THE CORNER POSTS PROPERLY.**

NOTE: DO NOT TIGHTEN UNTIL ALL BOLTS, NUTS, AND WASHERS ARE IN PLACE.

**YOU MAY HAVE TO DRIVE THE LAG SCREWS IN AT AN ANGLE TO CONTACT THE COR-NER POSTS PROPERLY.**

Bottom of large circular opening in the FACE PLATE ENTRY is flush to the TOP of the deck.

FACE PLATE ENTRY

STEP 2: ASSEMBLING THE FIRST CURVED SECTION

Locate a top SLIDE SECTION (Labeled #2) with an overlapping flange and a bottom SLIDE SECTION (Labeled #3) without an overlapping flange. Fasten the top and bottom SLIDE SECTIONS together along the flanges (ribs) with 5/16” x 1” hex bolts and 5/16” lock nuts. Use a washer on both sides of the flange (rib). Make sure to place a nut/bolt with washers in each hole provided on the inside and outside ribs of the SLIDE SECTIONS.


STEP 3: ATTACHING FIRST CURVED SECTION TO FACE PLATE ENTRY SECTION

Now that the first CURVED SECTION is assembled, raise it up to the FACE PLATE ENTRY SECTION with the RIB vertical and the CURVED SECTION facing down. The RIB in the CURVED SECTION will get ro-tated TWO holes to the RIGHT. Align the holes in each of the flanges of the FACE PLATE ENTRY SECTION and the first CURVED SECTION. Fasten the sections together with 5/16” x 1” hex bolts, 5/16” washers and 5/16” Lock Nuts. Use a washer on both sides of the flange. Fasten the sections together at the TOP and BOT-TOM first, then fasten the rest of the nuts/bolts.

NOTE: DO NOT TIGHTEN THE FASTENERS UNTIL ALL BOLTS, NUTS AND WASHERS ARE IN PLACE.

TWO holes between mid-line and RIB.

Mid-Line

RIB

Rotate RIGHTTWO holes.

FACE PLATE ENTRY SECTION

first CURVED SECTION


STEP 4: ASSEMBLING THE SECOND CURVED SECTION

Locate a top SLIDE SECTION (Labeled #2) with an overlapping flange and a bottom SLIDE SECTION (Labeled #3) without an overlapping flange. Fasten the top and bottom SLIDE SECTIONS together along the flanges (ribs) with 5/16” x 1” hex bolts and 5/16” lock nuts. Use a washer on both sides of the flange (rib). Make sure to place a nut/bolt with washers in each hole provided on the inside and outside ribs of the SLIDE SECTIONS.


STEP 5: ATTACHING SECOND CURVED SECTION TO FIRST CURVED SECTION

Now that the second CURVED SECTION is assembled, raise it up to the first CURVED SECTION aligning the RIBS in the sections. The CURVED SECTIONS should make a “U” shape at this point. Rotate the RIB in the second CURVED SECTION two holes to the LEFT. Fasten the second CURVED SECTION to the first CURVED SECTION with 5/16” x 1” hex bolts, 5/16” washers and 5/16” lock nuts. Use a washer on both sides of the flange. Fasten the sections together at the TOP and BOTTOM first, then fasten the rest of the nuts/bolts.


TWO holes between ribs.

RIB

second CURVED SECTION

first CURVED SECTION

STEP 6: EXIT SECTION ASSEMBLY

Locate the top EXIT PIECE (Labeled #4 with large cutout section) and the bottom exit piece (Labeled #5 this is the only curved section remaining). Fasten the exit pieces along the ribs with 5/16” x 1” long bolts and nuts provided using a washer on both sides of the flange. Make sure to fasten the nuts and bolts in each hole pro-vided on the ribs, on both sides of the top and bottom exit pieces.


EXIT PIECE(with cut out section)

Bottom exit piece(This is the last curved slide section left.)

STEP 7: ATTACH FOOT STAND TO EXIT SECTION

Locate the FOOT STAND PIECE. Rotate the FOOT STAND PIECE so that the there is one hole showing on the LEFT on the EXIT SECTION. Fasten the FOOT STAND PIECE to the EXIT SECTION with 5/16” x 3/4” long bolts and washers. Make sure to fasten all 6 bolts in each of the holes provided in the FOOT STAND PIECE.

ONE hole should be showing here.

FOOT STAND PIECE

EXIT SECTION

STEP 8: ATTACHING THE SECOND CURVED SECTION TO THE EXIT SECTION

Now that the EXIT SECTION and FOOT STAND PIECE are assembled, raise the EXIT SECTION up to the second CURVED SECTION and align the holes in the flanges of the second CURVED SECTION and the EXIT SECTION so that the foot rests squarely on the ground. Fasten the EXIT SECTION to the second CURVED SECTION with 5/16” x 1” hex bolts and 5/16” lock nuts using a 5/16”washer on each side of the flange. Fasten the sections together at the TOP and BOTTOM first, then fasten the rest of the nuts/bolts.


TWO holes between ribs.

NOTE: OTHER SECTIONS NOT SHOWN FOR CLARITY.

second CURVED SECTION

EXIT SECTION

THIS IS THE COMPLETED SUPER TUBE ASSEMBLY

LIMITED THREE YEAR WARRANTY

1. Subject to proper installation, Kid’s Creations, L.L.C. warrants, subject to the limitations stated below, to the original retail purchaser that all Kid’s Creations, L.L.C. playground equipment and structures and each component part will be free from defects in workmanship and materials for a period of three (3) years. In addition, Kid’s Creations, L.L.C., warrants all ropes and canvas for a period of one (1) year. 2. Additionally, Kid’s Creations, L.L.C. warrants to the original purchaser that all redwood components will be free from deterioration which impairs the structural integrity of the unit for the life time of the original purchaser. Wooden components in your Kid’s Creations, L.L.C. system will have imperfections, seasonal and surface cracks, knot holes and knots. Natural characteristics of all wooden play equipment, not resulting in structural failure, are not covered under this warranty. 3. Kid’s Creations, L.L.C. reserves the right to examine photographs or physical evidence of equipment claimed to be defective, and to recover said equipment, prior to disposition of warranty claims. Equipment returned to our factory for examination or recovery must be shipped freight prepaid, unless a Return Authorization Number is issued. 4. No warranty is offered on equipment subjected to abuse, negligence, improper installation, vandalism, acts of God, unauthorized alteration or attachment to equipment other than our own, or improper use, service or repair by customer or any third party. Please supervise your children’s play activity and maintain your play equipment periodically. 5. This warranty is limited to equipment used for residential, single-family dwellings and specifically excludes commercial or institutional use. 6. The term of the warranty begins on the date the equipment is delivered to the purchaser or such destination as the purchaser shall designate. 7. In the event of a defect covered by this warranty, Kid’s Creations, L.L.C. will remedy the defect, without charge, to the purchaser within a reasonable time. The remedy will consist of repair or replacement of the equipment, or refund of the purchase price, at the option of Kid’s Creations, L.L.C. 8. KID’S CREATIONS, L.L.C. DISCLAIMS ALL OTHER REPRESENTATIONS AND WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, IN FACT OR IN LAW, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTY OF MERCHANTABILITY OR THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. 9. KID’S CREATIONS, L.L.C. SHALL NOT BE LIABLE FOR ANY INCIDENTIAL OR CONSEQUENTIAL DAMAGES FOR FAILURE TO PERFORM ITS OBLIGATIONS UNDER THIS AGREEMENT. ADDITIONALLY, INCIDENTAL AND CONSEQUENTIAL DAMAGES SHALL NOT BE RECOVERABLE EVEN IF THE REPAIR, REPLACEMENT, OR REFUND REMEDY FAILS OF ITS ESSENTIAL PURPUSE OR FOR ANY OTHER REASON. NOTWITHSTANDING ANY LANGUAGE TO THE CONTRARY SET OUT IN THIS WARRANTY, NOTHING IN THIS WARRANTY SHALL BE CONSTRUED TO LIMIT OR DISCLAIM ANY WARRANTY, WHETHER STATUTORY OR IMPLIED AT COMMON LAW, WHICH UNDER APPLICABLE STATE LAW, CANNOT BE LAWFULLY LIMITED OR DISCLAIMED. 10. To obtain performance of any obligation under this warranty or to inquire about warranty performance, the purchaser must contact Kid’s Creations, L.L.C., 800 N. Maple, Garnett, Kansas 66032, or call 866-483-4250. 11. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

1‐800‐437‐07841‐

costco high wire playset assembly instructions · 2020. 5. 8. · #27a top canopy support 1 #102...

Documents