corobore® xl spirogrooving™ - sandvik coromant · exploded assembly (large tool) alt 1. go...
TRANSCRIPT
CoroBore® XL SpiroGrooving™Handling instruction for pre-setting equipment
Exploded assembly (large tool)
Alt 1. Go through step 3-5
Alt 2. Go through step 1-5
KIT code: 820-xxxVB16-Cx
A = M10B = M6C = C8-R822XLS17-Ax 070C = C6-R822XLS17-Ax 058D = S17-820XL-40A-018E = SL-SVXBR-40A-16-050 SL-SVXBR-40A-16-085F = SL-SVXBL-40A-16-050 SL-SVXBL-40A-16-085H = 5549 051-01
KIT code: 820-xxxVB16X-Cx
A = M10B = M6C = C8-R822XLS17 Ax 070C = C6-R822XLS17-Ax 058D = S17-820XL-40A-018E = SL-SVXBR-40A-16-050 SL-SVXBR-40A-16-085F = SL-SVXBL-40A-16-050 SL-SVXBL-40A-16-085G = S17-820XL-40A-X18H = 5549 051-01
C × 1
E × 1
H × 1
A × 4
B × 12F × 1
D × 2
C × 1D × 1
E × 1
H × 1
A × 4
B × 12F × 1
G × 1
1. 2. Axial adjustability for large tool
O.D
I.D
P.DP.D/2
*O.D **I.DA×2 A×2
P.D/2
*SL-SVXBR-40A-16-050 = O.D*SL-SVXBR-40A-16-085 = O.D**SL-SVXBL-40A-16-050 = I.D**SL-SVXBL-40A-16-085 = I.D
Alt. 2 Alt. 2
3. 4.
Alt. 1/Alt. 2 Alt. 1/Alt. 2
*SL-SVXBR-40A-16-050 = O.D*SL-SVXBR-40A-16-085 = O.D**SL-SVXBL-40A-16-050 = I.D**SL-SVXBL-40A-16-085 = I.D
0.2 mm +-0.030.008 inch +-0.0011
0.2 mm +-0.030.008 inch +-0.0011
*O.D **I.D
O.D
I.D
P.DP.D/2
*O.D **I.DA×2 A×2
P.D/2
5.
Alt. 1/Alt. 2
CoroBore® XL SpiroGrooving™Small
0.4 mm0.016 inch
*O.D
75Nm
**I.DA×2 A×2
Exploded assembly (small tool)
Alt 3. Go through step 3-5
Kit code: 820-75VC11-C5
A = M8B = M4C = C5-R822XLS14- AI040D = S14-820XL-25A-017E = SL-SVXCR-25A-11-030 F = SL-SVXCL-25A-11-030H = 5549 051-02
Alt 4. Go through step 1-5
Kit code: 820-75VC11X-C5
A = M8B = M4C = C5-R822XLS14- AI040D = S14-820XL-25A-017E = SL-SVXCR-25A-11-030 F = SL-SVXCL-25A-11-030G = S14-R820XL-25A-X17H = 5549 051-02
C × 1
E × 1
H × 1
A × 4
B × 12F × 1
D × 2
C × 1D × 1
E × 1
A × 4
B × 12 F × 1
H × 1G × 1
1.
Alt. 4*SL-SVXCR-25A-11-030 = O.D**SL-SVXCL-25A-11-030 = I.D
2. Axial adjustability for small tool
Alt. 4
O.D
I.D
P.D/2
*O.D **I.DA×2 A×2
P.D/2
P.D
3.
Alt. 3/Alt. 4*SL-SVXCR-25A-11-030 = O.D**SL-SVXCL-25A-11-030 = I.D
4.
Alt. 3/Alt. 4
*O.D **I.D
0.2 mm +-0.030.008 inch +-0.0011
0.2 mm +-0.030.008 inch +-0.0011
O.DI.D
P.D/2
*O.D **I.DA×2 A×2
P.D/2
P.D
5.
Alt. 3/Alt. 4
*O.D
38Nm × 2
**I.D
0.4 mm0.016 inch
A×2 A×2
www.sandvik.coromant.com/spirogrooving
92026© AB Sandvik Coromant 2015.03Rev 2016.10
Head office: AB Sandvik Coromant SE-811 81 Sandviken, Swedenwww.sandvik.coromant.com E-mail: [email protected]