contour and topo map applications
DESCRIPTION
Contour and Topo map Applications. Profile View (Longitudinal Sections): Roads , Canals, Pipes ,… Cross-Sectional View, Roads, Canals, Pipes , Building,…. Chapter 6-Vertical Sections. Longitudinal Sections- Vertical section along the centerline of the complete length of the work. - PowerPoint PPT PresentationTRANSCRIPT
![Page 1: Contour and Topo map Applications](https://reader036.vdocuments.mx/reader036/viewer/2022062314/56813c20550346895da598bb/html5/thumbnails/1.jpg)
Contour and Topo map Applications
Profile View (Longitudinal Sections): Roads, Canals, Pipes,…
Cross-Sectional View, Roads, Canals, Pipes, Building,…
![Page 2: Contour and Topo map Applications](https://reader036.vdocuments.mx/reader036/viewer/2022062314/56813c20550346895da598bb/html5/thumbnails/2.jpg)
Chapter 6-Vertical Sections
Longitudinal Sections- Vertical section along the centerline of the complete length of the work.
Cross-Section : Vertical sections drawn at right angles to the center line.
CUT (Level and slope- Upward from formation )Fill or Embankments ( Downward from
Formation)
Applications1. Determining suitable gradients 2. Calculating the volume of earth work.3. Supplying details of depth of cutting or height of filling required.
![Page 3: Contour and Topo map Applications](https://reader036.vdocuments.mx/reader036/viewer/2022062314/56813c20550346895da598bb/html5/thumbnails/3.jpg)
Important pointsLeveling data and or contour map be obtained.Scale should be as large as possible as it required or limited by paper size. Drawing should shows maximum possible details.Horizontal scale is determined by the length of horizontal distance and the paper size. Vertical scale is determine by the difference of maximum and minimum reduce levels and the paper size. If the difference is small then larger scale is needed. On other hand if the difference if large then small scale should be considered.Design elements must be available, example road (formation) width, building dimension, soil side slope,…Datum: select datum level based on the lowest RL that is included I n the drawing .
![Page 4: Contour and Topo map Applications](https://reader036.vdocuments.mx/reader036/viewer/2022062314/56813c20550346895da598bb/html5/thumbnails/4.jpg)
Example 1
.Draw with proper scale on A4 the profile view of a propose roads as show on the figure below AB (level) point A follows natural terrain BC is level RL B = RL C =75.18m
CD. EF , RL E is 65 and RL F is 75 .
![Page 5: Contour and Topo map Applications](https://reader036.vdocuments.mx/reader036/viewer/2022062314/56813c20550346895da598bb/html5/thumbnails/5.jpg)
E
F
A
B
C
![Page 6: Contour and Topo map Applications](https://reader036.vdocuments.mx/reader036/viewer/2022062314/56813c20550346895da598bb/html5/thumbnails/6.jpg)
Road center line (R1 and R$) W 4.00 M, G 1: 50 Side slope 1: 1
Storm water rising 1 in 40Invert manhole S1 -2.97
Foul water rising 1 in 40Invert manhole S1 -2.95
Example 2
![Page 7: Contour and Topo map Applications](https://reader036.vdocuments.mx/reader036/viewer/2022062314/56813c20550346895da598bb/html5/thumbnails/7.jpg)
Longitudinal section-Profile viewData collected and reduced
R1 @ 4.400R4 (80) will 6.000Slope 1in 50
HPC RL
6.55 5.200
![Page 8: Contour and Topo map Applications](https://reader036.vdocuments.mx/reader036/viewer/2022062314/56813c20550346895da598bb/html5/thumbnails/8.jpg)
Calculation
![Page 9: Contour and Topo map Applications](https://reader036.vdocuments.mx/reader036/viewer/2022062314/56813c20550346895da598bb/html5/thumbnails/9.jpg)
Longitudinal section-Profile viewAlong Road centerline
![Page 10: Contour and Topo map Applications](https://reader036.vdocuments.mx/reader036/viewer/2022062314/56813c20550346895da598bb/html5/thumbnails/10.jpg)
Examples- Sewer line
Sewer is 0.80 m in widthExcavation: Vertical
![Page 11: Contour and Topo map Applications](https://reader036.vdocuments.mx/reader036/viewer/2022062314/56813c20550346895da598bb/html5/thumbnails/11.jpg)
![Page 12: Contour and Topo map Applications](https://reader036.vdocuments.mx/reader036/viewer/2022062314/56813c20550346895da598bb/html5/thumbnails/12.jpg)
Cross-Sections at 40 (RL is 5.200 and 60 (Rl is 6.800). Side Slope 1:1 Width 4:00 m
![Page 13: Contour and Topo map Applications](https://reader036.vdocuments.mx/reader036/viewer/2022062314/56813c20550346895da598bb/html5/thumbnails/13.jpg)
Examples-Page 106
![Page 14: Contour and Topo map Applications](https://reader036.vdocuments.mx/reader036/viewer/2022062314/56813c20550346895da598bb/html5/thumbnails/14.jpg)
Cross-Sections Data
![Page 15: Contour and Topo map Applications](https://reader036.vdocuments.mx/reader036/viewer/2022062314/56813c20550346895da598bb/html5/thumbnails/15.jpg)
![Page 16: Contour and Topo map Applications](https://reader036.vdocuments.mx/reader036/viewer/2022062314/56813c20550346895da598bb/html5/thumbnails/16.jpg)
Draw sectional view along AB, AC, CD and BD sides of the building. AB=50 meter and CD =40 meter
A B
C D
![Page 17: Contour and Topo map Applications](https://reader036.vdocuments.mx/reader036/viewer/2022062314/56813c20550346895da598bb/html5/thumbnails/17.jpg)
HomeworkA uniform slope 5 meter road is proposed between point A and B, soil side slope Is 30 degrees. Perform the following:
1. Draw to maximum scale on A4 a profile view of the road, show the formation location2. Compute cut and fill along the center line for every station3. Draw to proper scale the cross section at station A, B and every 20 meter