contemporary english a m m f f installation and user guide b · 2020. 9. 3. · 5 re-enter user...
TRANSCRIPT
1 / 4
Installation and User Guide
EN
GLI
SH
Required tools
Ruler4 AA Batteries
Hammer Wood block
Phillips head screwdriver
Additional Tools (depending on application)
WeiserUSA: 1-800-677-5625
Canada: 1-800-501-9471www.weiserlock.com
A
N or P (2x)
AB
B
N P
S
Q R
If drilling a new door, use the supplied template and the complete door drilling instructions available at www.weiserlock.com/doorprep.
Note: Additional door preparation may be required for doors with 1-1/2" (38 mm) holes. Consult the deadbolt drilling instructions at www.weiserlock.com/doorprep.
or
backset
Measure to confirm that the hole in the door is either 2-1/8" (54 mm) or 1-1/2" (38 mm).
Measure to confirm that the backset is either 2-3/8" or 2-3/4" (60 or 70 mm).
2-3/8" or 2-3/4"60 or 70 mm 1-3/8" – 2"
35 – 51 mm
Measure to confirm that the hole in the door edge is 1" (25 mm).
Measure to confirm that the door is between 1-3/8" and 2" (35 mm and 51 mm) thick.
A
A D
B C D
Is the door edge chiseled? Which latch are you installing?
2-1/8"
54 mm
1-1/2"
38 mm
1"
25 mm
YES NO
Use latch “A”. If the latch bolt is not already extended, extend the latch bolt as shown.
wood block
actual size
Use latch “B”. If the latch bolt is not already extended, extend the latch bolt as shown.
Latch “A” Latch “B”
S (2x) C
Q or R (2x)
Longer screws install closest to the door jamb.
door frame
E Install strike on the door frame.
Make sure the hole in the door frame is drilled a minimum of 1" (25 mm) deep.
orchiseled not chiseled
or
1 Prepare the door and check dimensions
2 Install the latch and strike
64002-002Rev 02GED1700
Latch
Strike
C
Keys
E
Exterior Assembly
Adapter Ring
D
Mounting Plate
Parts in the box
Fasteners
03809
N
P
48654 64109 T V
49191
U
Contemporary
Interior Assembly
SmartKey Tool
H
Traditional
MM
Traditional
F F
Contemporary
K L
G
SL03031011
QR
S
A
B
A
B
A B
B
C Is the D-shaped hole centered in the door hole?
Hold the latch in front of the door hole, with the latch face flush against the door edge.
YES NO
No adjustment is required. Proceed to next step.
D-shaped hole D-shaped hole
Rotate latch face as shown to extend latch.
or
2 / 4
K
Install 4 AA batteries in battery pack. Press and HOLD the Lock button while installing battery pack.
Hold button until the latch bolt starts moving on its own.
Did the latch bolt retract and extend on its own when the battery pack was installed?
A B C
YES NOor
Door handing process was successful! Proceed to next step after latch
bolt stops moving.
Remove battery pack, wait 15 seconds, then
attempt the process again.
Note: Latch bolt will only retract half way.
Ensure correct polarity. For best results, use new, non-rechargeable Alkaline batteries only.
This step will teach your lock the orientation of your door and is crucial to lock operation.
2-1/8"
54 mm
1-1/2"
38 mm
What is the diameter of the hole in the door?
Locate screws for step 3C and keep them within reach.
Install exterior keypad and mounting plate.A
B
C
Diameter is 2-1/8" (54 mm)
Diameter is 1-1/2"(38 mm)
or
“D” is required for installation. Install “D” on “F”.
“D” is not needed for installation. Discard “D”. Cable goes
underneath latch.
Support exterior assembly during mounting plate installation.
Route cable through center hole, then push cable into bottom hole.
Insert key and test latch. If latch does not extend or retract smoothly, adjust screws (T).
Remove key when finished and make sure the latch bolt is fully extended.
Keep parallel to edge of door.
Tighten screws evenly.
a
c
b
d
actual size
T
D
DF
F
G
TT (2x)
T
E
Install the exterior keypad
U
actual size
U(2x)
Remove battery cover and battery pack from interior assembly. Install interior assembly onto mounting plate.A B
a
c
b
d
Make sure turnpiece is in the vertical position.
Make sure turnpiece shaft is rotated as shown.
Do not install batteries
until step 5.
Ensure tight cable connection.
Lay excess cable flat inside the bottom of the interior housing.
align
La
c
b
d
M
L
L L
K
bottom hole
3
4 Install the interior assembly
5 Install the batteries and perform the door handing process
3 / 4
1x
green
3x
red
Confirm that the code(s) added in previous step can unlock the door.
One green flash with one beep Three red flashes with three beepsor
Make sure the door is open. Press the Program button once.
Locking the Door Unlocking the Door
Enter user code. A total of 16 user codes may be programmed.
Press Lock button once.A B C
What lights and sounds does the lock produce?D
Each user code must be a unique
code between 4 and 8 digits.
Programming was successful. Programming was unsuccessful.
Make sure not to pause for more than 5 seconds during programming.
Make sure the user code is not a duplicate and that it is between 4 and 8 digits during your next attempt. Make sure the lock has room for an additional code. If
all user code positions are filled, delete a code to make room for this one.
Press Lock button once. Enter user code.
*Beeping sound will only be heard if switch #3 (on the lock interior) is in the on positon. See “Switches and Status LED Colors” on page 4.
Programming Timeout During programming, if no button is pressed for five seconds, the system will time out (indicated by three beeps and a red flashing keypad), and you will need to restart the procedure.
Mastercode
For enhanced security, a mastercode may be used when adding and deleting user codes. For more information about the mastercode, download the Programming and Troubleshooting Guide on the SmartCode 10 page at www.weiserlock.com.
Re-key the lock (if needed). Install the battery cover.A B
IMPORTANT: Remove battery pack before re-keying.
actual size
M
V (3x)
V
K
H
Ka ab bc
Re-key the lock to work with your existing key. See the supplied SmartKey Re-key instructions for more information.
Reinstall battery pack.
7
8
6 Add user codes (16 max)
Re-key the lock (if needed) and install the battery cover
Test the lock (review normal operation)
Alert Reason Solution
Keypad flashes red three times with three beeps*.
One incorrect code entered. Re-enter code.
No user code programmed. Program at least one user code.
Programming timeout after five seconds. Attempt programming procedure again.
Unsuccessful programming.
Keypad flashes red 15 times with 15 beeps*
Three incorrect codes entered within one minute.
Re-enter code after 60 second keypad lockout.
Keypad flashes red with fast beeping sound for three to four seconds.
Low battery. Replace batteries.
Keypad flashes green with continuous beeping sound for two seconds.
Door jammed while attempting to lock.
Manually re-lock door. If needed, reposition strike.
*Beeping sound will only be heard if switch #3 is on.
4 / 4 © 2016 Spectrum Brands, Inc.
If no button is pressed for five seconds, the system will time out, and you will need to restart the procedure.
1 Keep door open. Press Program button once.
5 Re-enter user code. 6 Press Lock button once.
If unsuccessful
Make sure to enter the same valid code in steps 3 and 5.
Test code
While the door is open, test the user code to make sure it no longer unlocks the door.
2 Press Lock button once.
4 Press Lock button once.
3 Enter user code to be deleted.
SmartCode at a Glance
Deleting a single user code
Note: All codes may be deleted at once if the mastercode is enabled. For more information about the mastercode, consult the online Programming and Troubleshooting Guide.
Reference Guide
Exterior
Back panel
Program button
Status LED
Switches
Turnpiece shaft
Note: When the cover is removed, the turnpiece shaft can be used to
manually lock and unlock the door.
Interior (cover removed)
Switches and Status LED colors Troubleshooting
Switch Function
1Door lock status LED blinks every 6 seconds
2Lock automatically re-locks door 30 seconds after unlocking. Disabled if no codes are programmed.
3 Audio
4 Not used.
Color Lock Status
Blinking green Unlocked
Blinking amber Locked
Blinking red Low battery
Solid red
Door handing process did not work properly. See the online Programing and Troubleshooting Guide.
1 2 3 4
On
Switches
Status LED
Off
System Alerts
Factory Reset
A factory reset will delete all codes associated with the lock.
Status LED
1 Remove battery pack.
2 Press and HOLD the Program button while reinserting the battery pack.
Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
Keypad
Lock button
KeywaySmartKey tool hole
3 Press the Program button once more. In 20 seconds, when the LED flashes green and you hear one beep, the lock has been reset.
4 Perform the door handing process again to teach the lock the orientation of the door and add user codes to your lock.
A complete Programming and Troubleshooting Guide is available on the SmartCode 10 page at www.weiserlock.com.
1. Read all instructions in their entirety.
2. Familiarize yourself with all warning and caution statements.
3. Remind all family members of safety precautions.
4. Protect your user codes and mastercode.
5. Dispose of used batteries according to local laws and regulations.
CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel can change the user codes, you must restrict access to the back panel and routinely check the user codes to ensure they have not been altered without your knowledge. The use of a mastercode can help protect your system’s settings.
WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional.
Important Safeguards