Integra Telecom I 4690 Colorado St SE I Prior Lake, MN 55372 I 952.226.7000 I www.getintegra.com

CONNECTING YOUR TVCONNECTING YOUR TV

Analogue AV output

RF Modulator output

HDMI output

RF input*

DC power input

USB

Ethernet

Optical S/PDIF output

Service button. No function in normal use. Only used under guidance from your service provider

1 6

7

8

9

2

3

4

51

2 6

3 4 895 7

REAR PANEL

1 CONNECTING YOUR STB TO THE TV

Choose one connection method in decreasing order of quality (high-low):

a. HDMI. (Best quality)

b. Analog (Good quality using the adapter cable from Integra)

c. RF. OK quality. The RF cable must be connected directly to a TV tuner input. This output connector MUST NOT be connected to any cable distribution network, satellite dish or antenna.

*A TV terrestrial antenna or cable connection may only be made to the RF input to provide loop

TV TVTV

ca

b

Connections to a cable distribution system must be made through a galvanic isolator.through functionality to the TV via the set-top box.

Component - Provides HD to HD TVs(5 connectors)

Composite - Does not provideHD to your TVs(3 connectors)

Your Integra installer will connect the Digital TV Set Top Box to your TV in one of several ways depending on your TV and the Digital TV programming you have chosen. Please follow these instructions for information on making changes to your system (adding HD programming, setting up a new TV etc.)

If you have selected an HD programming package, your TV must be connected to your Set Top Box using either HDMI or Component cables to view HD programming. The cable you select will depend on the avail-able inputs on your TV. HDMI cables are available from Integra or from many electronic retailers. If you choose to use Component connections, you will need the adapter cable available only from Integra.

IMPORTANTConnect the black connectorto the red AUDIO input of your TVfor both Composite or Component

HDMI - Best options forHD to your TVs(connect to “a”)

Connect adapter cable to “b”

Integra Telecom I 4690 Colorado St SE I Prior Lake, MN 55372 I 952.226.7000 I www.getintegra.com

In order to view HD programming on your TV, please follow these steps:

1. Verify you have added an HD programming package by calling Integra at 952.226.7000

2. Verify that your TV is connected to the Set Top Box with either a standard HDMI cable, or by using the Component cable adapter (white, black, green, blue, red)

If you need to change the cabling to your TV, follow these steps BEFORE changing your cables: 1. Press ‘Menu’ on your Integra remote then choose “My Settings” then “Display” 2. Change audio format to Dolby Digital 3. Change the TV Type to 16x9 4. Change Connector type to the cable type you plan to use to connect to the TV (HDMI or Compo nent) 5. Change the output resolution to 720 or 1080 depending on the resolution of your TV 6. Highlight the “Save” button and press “OK”

Your STB is now set to transmit to your TV in HD, you now need to connect the cable and set your TV to accept the HD signal. For HD service you may either use a standard HDMI cable or the Component Cable adapter (available free, only from Integra)

3. Connect your chosen cable to your Set Top Box and TV (use diagram on front page of this instruction sheet to locate the connector locations) (be sure to disconnect any coax or composite connections that may have been used in the past)

4. Using the remote that came with your TV (not the Integra remote), or buttons on the TV, change your TVs input to the proper input (ex. HDMI 1, or Comp. 2 etc.) this will change your TV to accept the signal from the input you connected your cable to.

5. Once you have selected the proper input, you will see programming from the STB. Test your HD channels by tuning to any 1XXX channel number.

If you have questions, be sure to call our local support team at 952.226.7000.

Integra Telecom I 4690 Colorado St SE I Prior Lake, MN 55372 I 952.226.7000 I www.getintegra.com