components for roll-off containers & skips

Catalogue 2020/2021

Components forRoll-off Containers & Skips

Stand 15062020

50© Rewald GmbH All rights of distribution, print or copy, also in the form of extracts, are reserved. Rights Reserved to make Technical Adjustments. Products only for intended use. Measurements in Millimeter. No liability is taken for printing errors

Over centre door lock standard version

The standard door locking hook always gives a few centimetres way un-der high pressure, which leads to a stronger pressure on the central lo-cking and can cause it to burst open. After having burst open, it can only be closed again after having emptied the container. The locking hook 452 180 / 453 015 and the locking hook seat 453 012 absorbs these forces.

Also any exterior damage to the lower locking hook, such as when the container is pushed backwards into a pile of scrap or debris, becomes much less likely.

Even after deformation of the doors the combination of hook 452 110 / 452 111 and hook seat 452 120 ensures opening and closing without problems.

Article no. Product Dimensions Description Price €452 108 Over centre door lock D=30mm includes the following articles on request452 110 Pin L=335mm S355J2 58,56452 111 Pin L=460mm S355J2 60,96452 120 Pin yoke S355J2 45,79452 120 01 Pin yoke repair plate 153x80x15mm S355J2, for pin yoke 452 120 7,84452 130 Guide S355J2 13,59452 140 Door lock shaft 30x2500mm for version D=30mm, S355J2 30,68452 160 Lever bar 30x900mm for version D=30mm, S355J2 16,88453 072 02 Bushing 31-50-80mm for version D=30mm, with lubrication, M8x1mm, 3 needed 8,96452 170 Bushing 31-50-40mm for version D=30mm, S355J2 5,82453 071 Washer 31-50-10mm for version D=30mm, S355J2 2,10452 150 Gusset plate 5x200x300mm S235JR 9,66452 180 Door locking hook d=31mm for version D=30mm, t=30mm, S355J2 22,03453 012 Seat for door locking hook t=50mm, cast steel, S355J2 35,86453 032 Safety lock for lever bar for version D=40mm 38,99

Article no. Product Dimensions Description Price €452 109 Over centre door lock D=40mm includes the following articles on request452 110 Pin L=335mm S355J2 58,56452 111 Pin L=460mm S355J2 60,96452 120 Pin yoke S355J2 45,79452 120 01 Pin yoke repair plate 153x80x15mm S355J2, for pin yoke 452 120 7,84452 130 Guide S355J2 13,59452 141 Door lock shaft 40x2500mm for version D=40mm, S355J2 41,57452 161 Lever bar 40x900mm for version D=40mm, S355J2 20,21452 173 Bushing 41-50-80mm for version D=40mm, S355J2, 3 needed 7,59452 171 Bushing 41-50-40mm for version D=40mm, S355J2 5,76452 172 Washer d=41mm for version D=40mm, S355J2 2,10452 150 Gusset plate 5x200x300mm S235JR 9,66453 015 Door locking hook d=41mm for version d=40mm, t=30mm, S355J2 22,03453 012 Seat for door locking hook t=50mm, cast steel, S355J2 35,86453 032 Safety lock for lever bar for version D=40mm 38,99

452 172 / 453 071

452 173 / 453 072 02

452 180 / 453 015

453 012

452 171 /-170

453 032

452 150

452 110 /-111

452 120 01

452 120

452 141 /-140

452 161 /-160

452 130

452 173 / 453 072 02

452 173 / 453 072 02

452 109 /-108

Stand 15062020


Ove

r ce

ntre

doo

r lo

ck s

tand

ard

vers

ion

/ saf

ety

lock

s fo

r le

ver

bar

/ doo

r lo

ck p

ins

Article no. Product Dimensions Description Price €453 041 Door lock pin D=12mm type A, galvanized, with chain 9,66453 036 Door lock pin D=14mm type A, galvanized, with chain 9,74453 037 Door lock pin D=16mm type A, galvanized, with chain 9,85453 040 Door lock pin D=20mm type A, galvanized, with chain 9,90453 039 Door lock pin D=12mm type B, galvanized, with chain 8,51453 046 Door lock pin D=14mm type B, galvanized, with chain 8,63453 038 Door lock pin D=16mm type B, galvanized, with chain 8,60453 042 Door lock pin D=20mm type B, galvanized, with chain 8,81453 040 02 Door lock pin D=15mm type C, galvanized 7,39453 044 Seat for door lock pin d=15mm S235JR 5,05453 045 Seat for door lock pin d=18mm S235JR 5,05453 043 Seat for door lock pin d=22mm S235JR 5,05

Door lock pins

240

12/14/16/20453 039 /-046 /-038 /-042

7

453 041 /-036 /-037 /-040

12/14/16/20

273

7 220

453 040 02

162

114

15

8

453 044 /-045 /-043

100

80

120

15/18/22

6

Safety locks for lever bar

- even when the container is full this Safety Lock ensures the save opening of the container doors by opening in 2 stages - locks automaticly when the Lever Bar is pushed back in place - for lever bars D=30mm or D=40mm

Utility model DE 20 2017 005 708.5

Article no. Product Description Price €453 032 Safety lock for lever bar for lever bar D=30/40mm 38,99453 031 Safety lock for lever bar for lever bar D=30mm, for containers with fixed roof 30,78

101

252

59

10

453 031

160

299

70

453 032

14

NEW

Stand 15062020


Article no. Product Dimensions Description Price €453 010 Door locking hook d=31mm t=18mm, top, flame cut, S355J2 13,36453 003 Door locking hook d=31mm t=15mm, flame cut, S355J2 12,25453 002 02 Door locking hook d=42mm t=20mm, forged, S355J2 11,78453 006 Door locking hook d=31mm t=20mm, flame cut, S355J2 19,04453 004 Door locking hook d=31mm t=16mm, flame cut, S355J2 13,05453 017 Door locking hook d=32mm t=18mm, forged, S355J2 12,93453 016 Door locking hook d=31mm t=20mm, forged, S355J2 10,01453 013 Door locking hook d=31mm t=20mm, forged, S355J2 11,98453 018 Door locking hook d=31mm t=20mm, forged, S355J2 15,47453 001 01 Door locking hook d=42mm t=20mm, forged, S355J2 16,15453 014 Door locking hook d=31mm t=20mm, cast steel, S355J2 10,66453 002 Door locking hook d=31mm t=20mm, flame cut, S355J2 13,46453 001 Door locking hook d=31mm t=20mm, forged, S355J2 18,36453 055 Seat for door locking hook D=40mm bottom 11,03453 050 Seat for door locking hook D=30mm top, Heavy-Duty Version 22,03453 051 Seat for door locking hook D=45mm top, Heavy-Duty Version 36,82

Door locking hooks

Article no. Product Dimensions Description Price €453 015 02 Door locking hook d=32mm t=30mm, bottom, S355J2 24,80*453 012 02 Seat for door locking hook t=50mm, S355J2, for door locking hook 453 015 02 34,37*

452 180

98,8

135,3

31

t=30

453 012453 015

140,9

41

104,

3t=30

453 015 02 453 012 02

Article no. Product Dimensions Description Price €452 180 Door locking hook d=31mm t=30mm, bottom, S355J2 22,03453 015 Door locking hook d=41mm t=30mm, bottom, S355J2 22,03453 012 Seat for door locking hook t=50mm, cast steel, S355J2 35,86

- strong & save, will hold even when doors are deformed - heavy duty


160

208

t=50

t=18

115

135

65

453 010

t=15

13380

145

453 003

t=16

453 004

175111,5

145

t=20

186127

103

453 016

t=18t=18

176119

148

453 017

t=20

200142

160

453 013

t=18

215152

160

453 018

t=20

14283

88

453 002 02

t=20

453 006

16291

211

t=20

453 001 01

289183

259 t=20

453 001

327

144

122

t=20

267

115 97

453 002

t=20

119

103

453 014

225

50500

30

118

60453 050

5015

810

0

453 051

600

45

453 055

40

45 6145 80

135

t=50

170

156

220

42

285,1

317

t=30

32

31 31 31 31 32 31 31

31 42

31 31 31

Stand 15062020


MARREL locking pins

Article no. Product Description Price €453 021 C-lock for UNP 180, S355J2 30,78453 022 C-lock for INP 180, forged, S355J2, DIN 30722-1 21,32453 023 C-lock for UNP 220, S355J2, DIN 30722-1/30722-2 41,61453 024 C-lock for INP 260, S355J2 58,77

C-locks

453 034

7287

90 7270 23

6984

1309070 22

90

453 035

Article no. Product Dimensions Description Price €453 035 MARELL locking pin 84x130x90mm cast steel, S355J2G3 34,27453 034 MARELL locking pin 87x90x72mm forged, S355J2G3 29,13

Doo

r lo

ckin

g ho

oks

/ set

of I

SO c

orne

r fi

ttin

gs /

C-lo

cks

/ MA

RREL

lock

ing

pins

180

120

52,5

80 170

t=50

453 021

70

180

52

80

t=50

453 022

82

90

171 22

0

128

52,5

80 209

80453 023

t=5026

0

109

248

52,5

80

113453 024

t=50

Article no. Product Description Price €453 025 Set of ISO corner fittings 1x top left, 1x top right, 1x bottom left & 1x bottom right 172,00

Set of ISO corner fittings

453 025

16264

7512

4

5164

80

178

117

16264

8012

4178

80

51

117

16264

7512

4

51 64

80

178

117

16264

8012

4

178

80

51

117

NEW

Stand 15062020


- locks automaticly when the container door is being closed - can be used instead of the usual locking shaft - less repairs and more safety - all parts are interchangeable - according to BGR

DE-Patent DE 10 2012 009 047.1

Automatic locking system

Article no. Product Price €453 057 Automatic locking system 139,21*

Article no. Product Dimensions Description Price €/item453 056 01 Seat for hook cast steel 30,45*453 056 05 Strut with hook L=1800mm strut S235R, hook cast steel 38,12*453 056 03 Mounting for strut cast steel 26,76*451 174 Spring bar 300x30x3mm 3 needed 12,18453 056 04 Handle 13,05*453 056 040 3 Bracket for handle cast steel 10,00*453 056 040 4 U-profile cast steel 9,57*453 056 040 2 Slide profile 50x38x20mm 1,96*

453 057

453 056 01

453 056 040 2

453 056 040 4

453 056 040 3

453 056 04

3x 451 174453 056 03453 056 05

1800

Stand 15062020


Aut

omat

ic lo

ckin

g sy

stem

/ lo

ckin

g sh

afts

/ ho

ok fo

r do

or s

haft

/ ac

cess

orie

s

Article no. Product Dimensions Description Price €453 080 Hook L=50mm t=25mm, cast steel 11,52453 073 Hook L=82mm t=30mm, cast steel 11,52453 074 Hook L=133mm t=30mm, cast steel 13,46453 078 Hook L=195mm t=25mm, cast steel 17,14453 072 04 Bushing 31-45-69mm with lubrication, M8x1, cast steel 7,52453 072 03 Bushing 31-45-69mm with lubrication, M10x1, cast steel 7,48453 072 02 Bushing 31-50-80mm with lubrication, M8x1mm, S355J2 8,96453 071 Washer 31-50-10mm S355J2 2,10

Locking shafts

Article no. Product Dimensions Description Price €453 070 10 Locking shaft, complete 30x500mm with hook L=96mm 39,15453 070 11 Locking shaft, complete 30x1050mm with hook L=172,5mm 58,75

Hook for door shaft / accessories

Article no. Product Dimensions Description Price €453 070 Locking shaft, complete 30x500mm with hook 453 073 L=82mm 39,17453 076 Locking shaft, complete 30x500mm with hook 453 074 L=133mm 40,39453 075 Locking shaft, complete 30x1200mm with hook 453 073 L=82mm 55,40453 077 Locking shaft, complete 30x1200mm with hook 453 074 L=133mm 57,46

Article no. Product Dimensions Description Price €453 131 Hook d=26mm cast steel 5,54453 132 Hook d=31mm cast steel 5,54453 079 Bearing plate d=31mm cast steel 5,08453 084 Bracket D=20mm cast steel 7,84

453 131

95

43

26

t=17

453 132

43

31

95

t=17

453 079

31

50

6544

15

453 084

45

15

4061

20

62

50

453 072 04

456931

M8x

1

45 69

453 072 03

31 M10x150 8031

453 072 02

M8x1

550 96

453 070 10

30

1050 172,5

453 070 11

30

453 070 /-076

453 075 /-077

82/133500

30

1200 82/133

30

5031

453 071453 080 /-078

50/195

31

25

453 073 /-074

82/133

31

30

16,5

16,5

Stand 15062020


Article no. Product Dimensions Description Price €453 061 Locking lever M12, complete strut L=300mm mit Halterung & Zugdruckachse 39,85453 062 Locking lever M12, complete strut L=330mm mit Halterung & Zugdruckachse 39,95453 060 Locking lever M12, complete strut L=500mm mit Halterung & Zugdruckachse 40,95453 063 Locking lever M12, complete strut L=1100mm mit Halterung & Zugdruckachse 43,07453 064 Locking lever M12, complete strut L=1500mm mit Halterung & Zugdruckachse, nach BG 45,68

Locking lever M12 & M14

Article no. Product Dimensions Description Price €463 057 Locking lever M14, complete strut L=1500mm with bushing for locking shaft, according to BG, galvanized 41,33

453 060 01

300/330/500/1100/1500

453 060 082

453 060 01

453 060 12

110 500 12

120 100 04

453 060 25

453 060 26

453 060 27

453 060 28

453 060 29

453 060 081

120 100 03

130 400 04

110 600 01

453 060 08

140 300 07

130 100 04

130 500 01

110 200 03

120 100 02

453 060 13

453 060 02

453 061 /-062 /-060 /-063 /-064

Article no. Product Dimensions Description Price €453 060 01 Pin 12x46mm for M12, with washer & split pin 3,34453 060 02 Hand lever L=249mm forged 11,98130 500 01 Spring washer 21-36-1,6mm DIN 137 B, B20 0,73140 300 07 Spring pin 6x35mm DIN 1481 0,60110 200 03 Hex head bolt M10x45mm DIN 933 1,50120 100 04 Hex head nut M12 left-hand thread, DIN 934 1,33120 100 03 Hex head nut M12 DIN 934 0,85453 060 08 Clevis d=12,5mm cast steel 6,00110 610 01 Cylinder head bolt M12x60mm DIN 912 1,33110 500 12 Eyebolt M12x70mm left-hand thread, DIN 444 5,39130 400 04 Cup washer 12,3x34x1,5mm DIN 2093, 6 needed 0,68453 060 12 Clevis mount d=12mm for locking shaft D=31mm, cast steel 10,03453 060 13 Base plate D=20mm cast steel 10,15130 100 04 Washer 21-33-4mm DIN 125, B21 0,25120 100 02 Hex head nut M10 DIN 934 0,49453 060 25 Strut L=300mm with threaded nuts M12 left & right-hand thread 9,24453 060 26 Strut L=330mm with threaded nuts M12 left & right-hand thread 9,68453 060 27 Strut L=500mm with threaded nuts M12 left & right-hand thread 10,33453 060 28 Strut L=1100mm with threaded nuts M12 left & right-hand thread 13,27453 060 29 Strut L=1500mm with threaded nuts M12 left & right-hand thread 14,73453 060 081 Threaded nut M12 3,01453 060 082 Threaded nut M12 left-hand thread 3,01

1500

376

463 057

31

Locking lever M14

Stand 15062020


Article no. Product Dimensions Description Price €463 043 Locking lever M16, complete strut L=320mm heavy dury version 50,04463 041 Locking lever M16, complete strut L=500mm heavy dury version 51,41463 040 Locking lever M16, complete strut L=1100mm heavy dury version 54,27463 050 Locking lever M16, complete strut L=1500mm heavy dury version, according to BG 55,47

Locking lever M16

Lock

ing

leve

r M

12 /

M14

/ M

16

463 043 /-041 /-040 /-050

Article no. Product Dimensions Description Price €463 040 06 Pin 16x50mm with washer & split pin, 2 needed for one locking lever 3,60463 040 13 Hand lever L=354mm cast steel 13,60130 500 01 Spring washer 21-36-1,6mm DIN 137 B, B20 0,73140 300 07 Spring pin 6x35mm DIN 1481 0,60110 200 03 Hex head bolt M10x45mm DIN 933 1,50120 100 06 Hex head nut M16 left-hand thread, DIN 934 1,59120 100 05 Hex head nut M16 DIN 934 0,98463 040 10 Clevis d=18mm cast steel 6,85110 600 02 Cylinder head bolt M16x60mm DIN 912 3,56110 500 13 Eyebolt M16x70mm left-hand thread, DIN 444 6,37130 400 03 Cup washer 16,3x34x1,5mm DIN 2093, 6 needed 0,73463 040 04 Clevis mount d=16mm for locking shafts D=31mm, cast steel 10,15453 060 13 Base plate D=20mm cast steel 10,15130 100 04 Washer 21-33-4mm DIN 125, B21 0,25120 100 02 Hex head nut M10 DIN 934 0,49463 050 04 Strut L=320mm with threaded nuts M16 left & right-hand thread 12,18463 050 01 Strut L=500mm with threaded nuts M16 left & right-hand thread 12,29463 050 02 Strut L=1100mm with threaded nuts M16 left & right-hand thread 14,68463 050 03 Strut L=1500mm with threaded nuts M16 left & right-hand thread 15,99453 060 083 Threaded nut M16 3,11453 060 084 Threaded nut M16 left-hand thread 3,11

320/500/1100/1500

453 060 083

120 100 05

130 400 03

110 600 02

463 040 10

140 300 07

130 100 04

130 500 01

110 200 03

120 100 02

453 060 13453 060 084

463 040 06

463 040 04

120 100 06

110 500 13

463 050 04463 050 01463 050 02 463 050 03

463 040 06

463 040 13

Stand 15062020


Article no. Product Dimensions Description Price €453 160 Tailgate lock, complete M20 with retaining spring 34,27453 164 Container bracket for M20 16,15453 155 Pin 18x75mm for eye bolt M20, galvanized, with cotter pin & washer 3,43453 144 Retaining spring d=21mm wire D=2mm, galvanized 2,45110 500 15 Eyebolt M20x200mm galvanized, continuous thread, DIN 444 11,41120 400 02 Ring nut M20 galvanized, DIN 582 6,37453 162 Door bracket for M20 13,84

Article no. Product Dimensions Description Price €453 160 1 Tailgate lock, complete M16 with retaining spring 32,33453 164 1 Container bracket for M16 7,39453 192 Pin 15x70mm for eye bolt M16, with cotter pin & washer 3,87453 144 1 Retaining spring d=17mm for M16, wire D=2mm, galvanized 2,31110 500 05 Eyebolt M16x200mm galvanized, DIN 444 7,99120 400 01 Ring nut M16 galvanized, DIN 582 3,21453 161 Door bracket for M16 13,84

Article no. Product Dimensions Description Price €453 140 Tailgate lock, complete M20 flat Version, retaining spring 34,27453 141 Container bracket for M20, flat Version, cast steel 7,82453 155 Pin 18x75mm for eye bolt M20, galvanized, with cotter pin & washer 3,43453 144 Retaining spring d=21mm wire D=2mm, galvanized 2,45110 500 15 Eyebolt M20x200mm galvanized, continuous thread, DIN 444 11,41453 143 Ring nut with slit M20 galvanized, slit 24mm 11,50453 142 Door bracket for M20, flat Version, cast steel 8,71

Article no. Product Dimensions Description Price €453 150 Tailgate lock, complete M20 with Retaining Spring 35,49453 141 Container bracket for M20, flat Version, cast steel 7,82453 155 Pin 18x75mm for eye bolt M20, galvanized, with cotter pin & washer 3,43453 144 Retaining spring d=21mm wire D=2mm, galvanized 2,45110 500 15 Eyebolt M20x200mm galvanized, continuous thread, DIN 444 11,41120 400 02 Ring nut M20 galvanized, DIN 582 6,37453 152 Door bracket for M20 17,42

Article no. Product Dimensions Description Price €453 134 Tailgate lock, complete TR20x4mm trapezoidal thread 31,54

453 143

453 141

453 155110 500 15

453 142

453 144

120 400 02

453 164

453 155110 500 15

453 162453 144

120 400 02

453 141

453 155110 500 15

453 152

453 144

120 400 01

453 164 1

453 192110 500 05

453 161453 144 1

453 160 1

20061

273

453 150

45

200273

453 140

45

200273

453 160

61

200280

453 134

204317

36,5

Tailgate locks

Stand 15062020


Article no. Product Dimensions Description Price €110 500 11 Eyebolt M12x70mm DIN 444 3,69110 500 14 Eyebolt M16x70mm DIN 444 5,30110 500 01 Eyebolt M16x120mm galvanized, DIN 444 6,26110 500 02 Eyebolt M16x140mm galvanized, DIN 444 6,74110 500 03 Eyebolt M16x160mm galvanized, DIN 444 7,56110 500 04 Eyebolt M16x180mm galvanized, DIN 444 7,83110 500 05 Eyebolt M16x200mm galvanized, DIN 444 7,99110 500 24 Eyebolt M16x200mm galvanized, continuous thread, DIN 444 9,36110 500 27 Eyebolt M18x200mm galvanized, DIN 444 10,47110 500 17 Eyebolt M20x100mm galvanized, DIN 444 8,62110 500 06 Eyebolt M20x120mm galvanized, DIN 444 8,32110 500 07 Eyebolt M20x140mm galvanized, DIN 444 8,70110 500 08 Eyebolt M20x160mm galvanized, DIN 444 9,41110 500 09 Eyebolt M20x180mm galvanized, DIN 444 10,17110 500 15 Eyebolt M20x200mm galvanized, continuous thread, DIN 444 11,41110 500 10 Eyebolt M20x220mm galvanized, DIN 444 11,08110 500 23 Eyebolt M24x180mm galvanized, DIN 444 12,18110 500 26 Eyebolt M24x250mm galvanized, eye d=25mm 14,16110 500 25 Eyebolt M24x270mm galvanized, DIN 444 13,71120 400 01 Ring nut M16 galvanized, DIN 582 3,21453 170 02 Ring nut with collar M16 galvanized, collar 3x18mm 5,22453 149 1 Ring nut M16 6,09453 149 2 Ring nut M18 6,05120 400 02 Ring nut M20 galvanized, DIN 582 6,37453 151 02 Ring nut with collar M20 galvanized, collar 3x22mm 8,20453 143 Ring nut with slit M20 galvanized, slit 24mm 11,50453 149 3 Ring nut M20 6,16453 146 Ring nut M20 galvanized 6,09120 400 03 Ring nut M24 galvanized, DIN 582 8,49453 143 1 Ring nut with slit M24 galvanized, slit 28mm 13,30453 149 4 Ring nut M24 6,36453 145 1 Key for ring nuts 500x50x12mm for M16, M20 & M24, galvanized 24,20453 177 Nut with handle M16 galvanized 8,08453 178 Nut with handle M20 galvanized 8,08

L

110 500 11 /-14 /-01 /-02 /-03 /-04 /-05 /-27 /-17110 500 06 /-07 /-08 /-09 /-10 /-23 /-26 /-25

Article no. Product Dimensions Description Price €453 180 Mounting plate d=17mm for M20 2,26453 181 Mounting plate d=16mm for M16 2,26453 190 Pin 16x64mm for M20, with cotter pin & washer 4,10453 191 Pin 15x64mm for M16, with cotter pin & washer 3,98453 144 Retaining spring d=21mm for M20, wire D=2mm, galvanized 2,45453 144 1 Retaining spring d=17mm for M16, wire D=2mm, galvanized 2,31

453 190 /-191

64

16/1

5

453 144 /-144 1

53

84 21/17

21/17

453 180 /-181

8030

2050

17/16

453 190 /-191

453 144 /-144 1

453 180 /-181

453 180 /-181

453 145 1

500

M20 M16 M24

110 500 24 /-15

L

120 400 01 /-02 /-03

35/40/50

62/7

1/90

63/72/90

453 170 02 /-151 02

35/40

65/7

4

63/72

453 143 /-143 1

40/50

71/9

0

72/90

453 149 1 /-2 /-3 /-4

35

103

60

453 146

70

76

70

453 177 /-178

31

30,5

25160

Tailgate locks in parts

Tailg

ate

lock

s / e

yebo

lts

/ rin

g nu

ts

NEW

Stand 15062020


Article no. Product Description Price €453 110 Flap lock left, forged 22,07453 111 Flap lock right, forged 22,07453 095 Stanchion key cast steel 20,40453 096 Stanchion pocket 6,49

Article no. Product Dimensions Description Price €453 085 Tailgate lock d=31mm left, hinged, side wall 64,61453 090 Tailgate lock d=31mm right, hinged, side wall 64,61453 100 Pin for tailgate lock 30x59mm 18,61

Tailgate locks

Flap locks for platform containers

Article no. Product Dimensions Description Price €459 184 Key ring 24x1,8mm rust free 0,53140 200 01 Retainer pin D1=2,8mm for shaft D2=11-14mm, DIN 11024, galvanized 0,57140 200 02 Retainer pin D1=3,6mm for shaft D2=14-20mm, DIN 11024, galvanized 0,76140 200 03 Retainer pin D1=4,5mm for shaft D2=20-26mm, DIN 11024, galvanized 1,20140 200 04 Retainer pin D1=5,6mm for shaft D2=26-34mm, DIN 11024, galvanized 1,99

459 184459 059

24 1,8

D1

140 200 01 /-02 /-03 /-04

Retainer pins & accessories

Article no. Product Dimensions Description Price €/meter459 059 Knotted chain D=1,6mm galvanized, DIN 5686, length according to specification 1,96

23

1,6 D2

453 096

130

110

1003732

8898

2025

453 100

453 085

453 100

453 090

11040

3125

6

453 085

120

3088

20559

30

453 100

99 26

84

31

253

15453 095

453 095

453 096

10070

55 80

453 110

240

15,5

8,5

Stand 15062020


Over centre locks

Article no. Product Dimensions Description Price €453 220 1 Over centre lock M12 with eye 453 219 02 11,08453 213 Over centre lock M12 with automatic safety latch, with padlock fitting, galvanized, with eye 453 219 12,31453 213 01 Over centre lock M12 with automatic safety latch, with padlock fitting, galvanized, with eye 453 219 01 12,72453 219 02 Eye M12 galvanized 3,90453 219 Eye M12 4,21453 219 01 Eye M12 galvanized, triangle 4,21

Article no. Product Dimensions Description Price €453 215 Over centre lock M10 cast steel, galvanized, with eye 453 214 18,00453 214 Eye M10 forged, galvanized 4,21

Article no. Product Description Price €453 222 Over centre lock with automatic safety latch, danish Model 6,74453 222 01 Over centre lock with automatic safety latch, danish Model, galvanized 7,40453 223 Counterhold for over centre locks for over centre locks 453 222 /-222 01 3,24453 223 2 Counterhold for over centre locks for over centre locks 453 222 /-222 01, galvanized, for mounting with screws 5,78

Article no. Product Description Price €453 210 1 Counterhold for over centre locks 3,15453 210 2 Counterhold for over centre locks 3,58453 230 Counterhold for over centre locks 1,89453 210 Counterhold for over centre locks forged 3,92500 211 Counterhold for over centre locks for mounting with screws, cast steel 4,38453 211 Counterhold for over centre locks for mounting with screws, galvanized 6,69500 300 Spring bolt bolt D=18mm 36,81

453 213

260-280

453 213 01

39

260-280

453 215 178

220-260

23

220830

453 223

88 66,5

30

453 222 /-222 01

128

222

8,5

453 210

34

30

14

130

135

185

500 300

18

Tailg

ate

lock

s / fl

ap lo

cks

for

plat

form

con

tain

ers

/ ret

aine

r pi

ns /

over

cen

tre

lock

s

453 210 1

31

28

3914

50

51

453 230

t=6

14

72

530 24

453 223 2

24

11

39

453 219 01 M12

30

453 219

M12

18

30

158

87,5

500 211 / 453 211

14

9

34

M12

M10

453 219 02 M12

72,5

20

M12

453 220 1

300-34020

18

M12

453 214 M10

23

30

453 210 2

12

66

30

41NEW

NEW

NEW

Stand 15062020


Article no. Product Dimensions Description Quantity scale Price €/item453 500 Over centre lock M14x2mm with automatic safety latch, with padlock fitting 1-9/from 10 24,35/18,49*453 510 Over centre lock M14x2mm with automatic safety latch 24,35453 501 Over centre lock M14x2mm with automatic safety latch, with padlock fitting, for mounting with screws, galvanized 25,32453 224 Over centre lock M14x1,5mm with automatic safety latch, with padlock fitting 24,35453 226 Over centre lock M14x1,5mm with automatic safety latch 24,35453 225 Over centre lock M14x1,5mm with automatic safety latch, with padlock fitting, for mounting with screws, galvanized 25,32453 229 Over centre lock M14x1,5mm with automatic safety latch, for mounting with screws, galvanized 30,34453 229 1 Over centre lock M14x1,5mm with automatic safety latch, for mounting with screws, galvanized 30,34

Over centre locks

453 510 /-226

295,5-32517

M14x2/1,5

453 500 /-224

295,5-325

17

M14x2/1,5

11

453 229

295,5-325

17 65

8,5 453 501 /-225

295,5-325

17

M14x2/1,5

7065

11965

453 229 1

238-252

14 49

7

M10x1,5

Over centre lid lock

M14x1,5

Article no. Product Dimensions Description Price €453 520 Lid lock M14 with automatic safety latch, with padlock fitting 44,36

11

M14

1715

49

453 520

910

665 210

Stand 15062020


Article no. Product Dimensions Description Price €453 511 Threaded eye M14x2mm spare part for 453 500 /-501 /-510 /-520, galvanized 5,14453 208 Threaded eye M14x1,5mm spare part for 453 200 /-201 /-204 /-205 /-224 /-225 /-226 /-229 /-231, galvanized 4,92453 203 Triangular eye M14x1,5mm spare part for 453 200 /-201 /-204 /-205 /-224 /-225 /-226 /-229 /-231, galvanized 5,12453 512 Threaded arm M14x2mm spare part for 453 500 /-501 /-510, galvanized 8,32453 227 Threaded arm M14x1,5mm spare part for 453 224 /-225 /-226 /-229, galvanized 8,32453 207 Eyebolt M14x1,5mm spare part for 453 200 /-201 /-204 /-205 /-231 4,89453 206 Handle L=185mm spare part for 453 200 /-204, forged 5,87140 300 01 Spring pin 8x40mm for 453 224 /-225 /-226 /-500 /-501 /-510 /-520, DIN 1481 0,58140 300 02 Spring pin 8x45mm for 453 200 /-201 /-204 /-205, DIN 1481 0,58

Ove

r ce

ntre

lock

s / o

ver

cent

re li

d lo

ck /

acce

ssor

ies

Article no. Product Dimensions Description Price €453 200 Over centre lock M14x1,5mm with padlock fitting 15,67453 201 Over centre lock M14x1,5mm with automatic safety latch, with padlock fitting 24,35453 204 Over centre lock M14x1,5mm 15,67453 205 Over centre lock M14x1,5mm with automatic safety latch 24,35453 231 Over centre lock M14x1,5mm with automatic safety latch, for mounting with screws, galvanized 25,67

Over centre locks

453 208

M14

x1,5

17

60

453 203

M14

x1,5

M14x1,5

17

240-280

453 204

M14x1,5

240-280

453 231

65 7017

65 9

M14x1,5

240-280

17

453 200

11M14x1,5

17240-280

453 201

11

M14x1,5

17

240-280

453 205

453 206

185

27,9

88,5

M14

x1,5

80

453 207

8,5

45 8

453 511

M14

x2

17

453 227

M14

x1,5

115

8,5

453 512

M14

x2

115

8,5

40 8

140 300 02 140 300 01

Stand 15062020


Article no. Product Dimensions Description Price €453 238 Bolt lock D=15mm with padlock fitting, left/right 9,57453 239 Bolt lock D=15mm with padlock fitting, right 8,59453 240 Bolt lock D=15mm with padlock fitting, left/right 10,40453 241 Locking plate d=22mm 4,04453 242 Bolt lock D=14mm galvanized 7,50453 243 Spring bolt D=15mm galvanized 7,73

Lid lock

453 237

Article no. Product Description Price €453 237 Lid lock with locking plates, with padlock fitting, for skip lids 15,23

453 243

57

15

5515

065

40 170200453 240

15

453 238

106

20512585

15

85 105205

453 239

8515

453 242

5835

118

14

130

50

25

22

453 241

t=8

45

172

100

142

38

6

8

Bolt locks

Stand 15062020


Lid

lock

/ bo

lt lo

cks

/ tai

lgat

e lo

cks

for

skip

s

25

130

453 372

Article no. Product Description Price €453 373 Safety latch cast steel 12,51453 374 Safety latch cast steel 12,51

Article no. Product Dimensions Description Price €/item453 347 Tailgate lock D=13mm size 1, left, hook L=125mm, plate 70x70mm, galvanized 9,59453 348 Tailgate lock D=13mm size 1, right, hook L=125mm, plate 70x70mm, galvanized 9,59453 350 Tailgate lock D=17mm size 2, left, hook L=170mm, plate 80x80mm, galvanized 9,24453 351 Tailgate lock D=17mm size 2, right, hook L=170mm, plate 80x80mm, galvanized 9,24453 360 Tailgate lock D=19mm size 3, left, hook L=210mm, plate 90x90mm, galvanized 12,98453 361 Tailgate lock D=19mm size 3, right, hook L=210mm, plate 90x90mm, galvanized 12,98453 353 Safety hook with chain D=3,8mm L=380mm, galvanized, packaging unit of 10 1,75453 346 Eye d=16,2mm for tailgate lock size 1, for welding 2,91453 349 Eye d=16mm for tailgate lock size 1, for welding, galvanized 3,76453 362 Eye d=20,2mm for Lock Latches Size 2+3, for welding 3,38453 363 Eye d=22mm for tailgate lock size 2/3, for mounting with screws, galvanized 9,55

67

200

334

80

453 371

88

140170

304

45

453 375

58

10

41/4

821

/27

39/42 14/16453 346 /-362

16,2

/20,

2

Tailgate locks for skips

Article no. Product Dimensions Description Price €453 371 Tailgate lock left, plate 10mm 35,77453 370 Tailgate lock right, plate 10mm 35,77453 375 Tailgate lock left, cast steel 36,86453 376 Tailgate lock right, cast steel 36,86453 372 Locking pin 25x130mm for tailgate locks 7,90

453 35338

0

3,8

3,6

453 349 /-363

126/

153

16/2

2

16/26

50/70

453 373 453 374

73

55,5

17,5

254090

55,5

17,5

2540

160/210/255125/170/210

8,5/10,5

70/80/9045/55/65

453 347 /-350 /-360

70/8

0/90

6,513/17/19

Stand 15062020


Article no. Product Dimensions Description Price €454 050 City lifting bar 35x80x300mm R50, cold-formed, S355J2+N 38,03454 051 City lifting bar 35x80x430mm R50, cold-formed, S355J2+N, DIN30722 45,15454 052 City lifting bar 35x80x1120mm R50, cold-formed, S355J2+N, DIN30722 46,77454 060 Welding plate 12x150x200mm d=36mm, for city lifting bar D=35mm, S355J2 17,40454 146 City lifting bar 35x330x310mm R120, cold-formed, S355J2+N 47,52

Article no. Product Dimensions Description Quantity scale Price €/item454 070 Lifting bar 50x100x500mm R75, cold-formed, S355J2+N 96,37454 090 Lifting bar 50x150x920mm R75, cold-formed, S355J2+N 98,51454 137 Lifting bar 50x150x1120mm R75, cold-formed, S355J2+N 96,79454 100 Lifting bar 50x100x1120mm R75, cold-formed, S355J2+N, DIN30722 1-4/from 5 77,22/69,60*454 101 Lifting bar 50x100x1120mm R75, forged, S355J2+N, DIN30722 108,07454 102 Lifting bar 60x100x1120mm R75, cold-formed, S355J2+N, DIN30722 107,34454 103 Lifting bar 60x100x1120mm R75, forged, S355J2+N, DIN30722 147,94454 104 Lifting bar 70x100x1120mm R75, cold-formed, S355J2+N 185,97454 111 Welding plate 250x300x8mm d=53mm, for lifting bars D=50mm, S355J2 13,59454 112 Welding plate 260x300x8mm d=53mm, for lifting bars D=60mm, S355J2 14,47

City lifting bars

Lifting bars

1120270 +/-20

R50

454 052

8035

8035

270 +/-20

R50

430454 051

8035

270 +/-20

R50

300454 050

R75

366 +/-20500

454 070

100

50

R75

100

50/6

0/70

390 +/-201120

454 100 /-101 /-102 /-103 /-104

330

215

31035

454 146

R120

100

200

50150

36

t=12

454 060

454 111 /-112

300

250/260

53/63

t=8

480 +/-20920/1120

454 090 /-137

R75

150

50

Stand 15062020


City

lift

ing

bars

/ lif

ting

bar

s

Article no. Product Dimensions Description Price €454 134 Lifting bar 50x190x720mm R75, cold-formed, S355J2+N 91,25454 135 Lifting bar 60x180x750mm R75, forged, S355J2+N 96,79454 138 Lifting bar 50x150x1120mm R100, cold-formed, S355J2+N 98,87454 138 1 Lifting bar 50x150x1120mm R100, forged, S355J2+N 104,41454 136 Lifting bar 50x115x1140mm R100, cold-formed, S355J2+N 92,68

Article no. Product Dimensions Description Price €454 160 Lifting bar 50x180x1120mm R75, cold-formed, S355J2+N 94,46454 161 Side plate 180x180x8mm d=51mm 9,92454 162 Cover plate 110x138x8mm 6,37

Article no. Product Dimensions Description Price €454 164 Lifting bar 50x215x600mm R50, cold-formed, S355J2+N 96,84454 165 Lifting bar 50x215x780mm R75, cold-formed, S355J2+N 96,84454 163 Lifting bar 50x345x1090mm R75, cold-formed, S355J2+N 121,11454 166 Lifting bar 50x345x1300mm R75, cold-formed, S355J2+N 118,24454 167 Reinforcing plate 90x380x15mm 22,40454 168 Reinforcing plate 100x130x15mm 9,16

Lifting bars

480 +/-20750

454 135

180

60

R75

402 +/-201140

454 136

115

50

R100

445 +/-201120

454 138 /138 1

150

50

R100

530 +/-201120

454 160

180

50

R75

400 +/-20600

454 164

215

50

R50

616 +/-20780

454 165

215

50

R75

710 +/-201090

454 163

345

50

R75

138

110

454 162

t=8

380

90

454 167

t=15

130

100

454 168

t=15

550 +/-20720

454 134

190

50

R75

180

180

454 161

t=8

51

875 +/-201300

454 166

345

50

R75

Stand 15062020


Gusset plates

Article no. Product Dimensions Description Price €454 114 Lifting bar plate 180x148x20mm d=51mm 35,64454 113 Lifting bar plate 250x185x30mm d=51mm 45,46454 125 Lifting bar plate 280x160x8mm left 12,36454 126 Lifting bar plate 280x160x8mm right 12,36454 124 1 Lifting bar plate 160x117x8mm left 7,50454 124 Lifting bar plate 160x117x8mm right 7,50454 123 1 Lifting bar plate 160x149x8mm left 13,44454 123 Lifting bar plate 160x149x8mm right 13,44

135

10020x45°

454 118

t=8

210

20x45°

340

270454 115

t=8

230

250

30

20x45°

454 116

t=8

260

20x45°170

454 117

t=8

140

20020x45°

454 122

t=8

130

20x45°137

454 127

t=8

200

20x45°

310

454 121

120

220

t=10

280

50x45°

454 119

300

t=10

230

20x45°240

454 120

t=10

Article no. Product Dimensions Price €454 118 Gusset plate 100x135x8mm 3,81454 127 Gusset plate 137x130x8mm 4,51454 122 Gusset plate 140x200x8mm 7,32454 117 Gusset plate 170x260x8mm 6,19454 116 Gusset plate 250x230x8mm 7,12454 115 Gusset plate 270x210x340x8mm 7,32454 121 Gusset plate 220x200x310x120x10mm 15,69454 120 Gusset plate 230x240x10mm 12,35454 119 Gusset plate 280x300x10mm 17,40

Lifting bar plates

83 55454 125

280

160t=8

55

83

280

t=8

454 125160

55

98

180

20454 114

t=20

14851

454 113

250200

185

t=30

t=8

117

160R35

454 124 1

t=8R35160

117

454 124

t=8

149

R22,5 160454 123 1

t=8

160R22,5

149

454 123

51

Stand 15062020


Lif

ting

bar

pla

tes

/ gus

set

plat

es /

lifti

ng b

ars

Article no. Product Dimensions Description Price €454 141 Lifting bar 50x25x380mm R734, cold-formed, S355J2+N 77,24454 140 Lifting bar 60x25x380mm R734, cold-formed, S355J2+N 90,81

Article no. Product Dimensions Description Price €454 149 Lifting bar 50x190x280mm R90, cold-formed, S355J2+N 93,12454 172 Lifting bar 50x300x320mm R110, cold-formed, S355J2+N 96,25454 142 Lifting bar 50x310x430mm R165, cold-formed, S355J2+N 96,56454 142 1 Lifting bar 50x323x400mm R148, forged, S355J2+N 101,14454 143 Lifting bar 50x335x300mm R100, cold-formed, S335J2+N 96,84454 145 Lifting bar 50x335x350mm R125, cold-formed, S355J2+N 96,25454 147 Lifting bar 50x535x400mm R150, cold-formed, S355J2+N 102,78

Lifting bars

Article no. Product Dimensions Description Price €454 159 Lifting bar 50x180x750mm R130, cold-formed, S355J2+N 89,61454 158 Lifting bar 50x200x580mm R130, cold-formed, S355J2+N 85,92454 151 Lifting bar 50x205x700mm R130, cold-formed, S355J2+N 89,61454 154 Lifting bar 50x300x900mm R200, cold-formed, S355J2+N 89,61454 153 Lifting bar 50x300x770mm R200, cold-formed, S355J2+N 89,61454 150 Lifting bar 50x323x500mm R150, cold-formed, S355J2+N 96,84454 148 Lifting bar 50x333x427mm R124, forged, S355J2+N 100,06454 157 Lifting bar 50x340x780mm R150, cold-formed, S355J2+N 96,84454 155 Lifting bar 50x340x390mm R90, cold-formed, S355J2+N 101,60454 156 Lifting bar 50x380x540mm R50, cold-formed, S355J2+N 101,89454 148 1 Lifting bar 50x450x450mm R128, cold-formed, S355J2+N 104,41454 152 Lifting bar 50x550x400mm R50, cold-formed, S355J2+N 102,20

190

100

28050

454 149

R90

535

385

40050

454 147

R150

335

210

35050

454 145

R125

335

235

30050

454 143

R100

323

175

40050

454 142 1

R148

250

140

32050

454 172

R110 310

145

43050

454 142

R165

50

38025

454 141

60

38025

454 140

180

750

50

454 159

R130 200

58050

454 158

R130

50

300

900

R200

454 154

50

300

770

R200

454 153

50

R150

323

500454 150

50

R150

340

780454 157

50

R90

340

390454 155

R12433

3

427454 148

50

50

550

400454 152

R50

50

380

540454 156

R50

450

450454 148 1

50

R128

205

700454 151

R130

50

Stand 15062020


Article no. Product Dimensions Description Price €454 180 Lifting bar, complete 50x970mm U-profile 200mm, primed, S355J2+N 232,91454 190 Lifting bar, complete 50x2300mm U-profile 200mm, unfinished, S355J2+N 367,42

Article no. Product Dimensions Description Price €454 182 Lifting bar, complete 50x900mm for volume containers, unfinished, S355J2+N , with lifting bar 454 149 211,51

Article no. Product Dimensions Description Price €454 183 Lifting bar, complete 50x900mm S355J2+N 182,71

454 180 /-190

454 183

454 182

280900

50

158

180

193

234,

5

75

346,5

200

50

199,

3

400970/2300

50

150

100280900

205

215

Lifting bars, complete

Article no. Product Dimensions Description Price €454 191 Lifting bar, complete 50x2300mm for container doors, swiveling, U-profile 200mm, S355J2+N 516,00

454 191

75

346,5

200

199,

3

50

400

2300133 133

1300NEW

Stand 15062020


Lift

ing

bars

/ he

avy

duty

lift

ing

bars

Article no. Product Dimensions Description Price €454 181 02 Lifting bar, complete 50x970mm U-profile 170mm, S355J2 154,43454 181 Lifting bar, complete 50x970mm U-profile 180mm, S355J2+N, heavy duty version 166,37454 181 03 Lifting bar, complete 60x970mm U-profile 170mm, S355J2 200,11454 181 01 Lifting bar, complete 60x970mm U-profile 180mm, S355J2+N, heavy duty version 215,34

454 181 02 /-181 /-181 03 /-181 01 390/400970

50/60280

70

170/

180 30

2

- very little wear - reduced noise - no welding needed

Article no. Product Dimensions Description Price €454 235 Heavy duty lifting bar, complete 75x972mm roller D=75mm 913,55454 235 01 Shaft 60x476mm 42CroMo4 71,78454 235 08 Roller 60-75-150mm with 2 bushings 182,71

Lifting bars

Article no. Product Dimensions Description Price €454 230 Heavy duty lifting bar, complete 55x972mm roller D=55mm 622,08454 231 Shaft 45x476mm 42CrMo4 52,28454 232 Roller 45-55-150mm with 2 bushings 82,25

Article no. Product Dimensions Description Price €454 220 Heavy duty lifting bar, complete 65x972mm roller D=65mm 630,78454 221 Shaft 50x476mm S355J2 52,28454 220 06 Roller 50-65-150mm with 2 bushings 84,86

454 230 /-220 972380

476

55/6

545

/50 240

381

200

75

454 235

972380

6075

476 320

381

200

75

454 232 /-220 06

454 231 /-221

454 235 08454 235 01

Heavy duty lifting bars

Stand 15062020


Article no. Product Dimensions Description Price €454 401 Hinged lifting bar, complete 50x900mm S355J2+N 378,47454 402 Hinged lifting bar 50x900mm S355J2+N 248,33

Hinged lifting bars

Article no. Product Dimensions Description Price €454 240 Hinged lifting bar 50x455mm S355J2+N, type LOTUS 380,26

Article no. Product Dimensions Description Price €454 215 Hinged lifting bar, complete 50x468mm universal, S355J2+N 444,42454 216 Hinged lifting bar 50x434mm S355J2+N 302,45454 217 Pin 40x96mm left, with chain 16,74454 217 01 Pin 40x96mm right, with chain 16,74454 218 Pin 40x116mm without chain 16,40140 300 03 Spring pin 8x70mm DIN 1481 0,95454 212 Washer 41-59-5mm 2,86454 214 Plate with pin safety latch 41,83454 219 Plate without pin safety latch 39,46

454 401

454 240

454 215

470380

455

50271

601

60

60

180

300 249

468

575

202

50

180

300

500405

900

29015

435

50

454 217

454 212

454 218

140 300 03

454 217 01

454 219

454 214

454 216

454 402

Stand 15062020


Hin

ged

lifti

ng b

ars

/ con

tain

er b

umpe

r

Article no. Product Dimensions Description Price €454 200 Hinged lifting bar, complete 50x970mm for 90º front wall, S355J2+N 546,65454 210 Hinged lifting bar, complete 50x970mm for 133º Front Wall, S355J2+N 571,30454 201 Hinged lifting bar 50x485mm S355J2+N 274,49454 202 Pin 50x96mm left, with chain 16,89454 202 01 Pin 50x96mm right, with chain 16,89454 203 Pin 50x116mm without chain 16,10140 300 03 Spring pin 8x70mm DIN 1481 0,95454 205 Washer 51-65-5mm 2,86454 206 Side plate left, for hinged lifting bar 454 200, with pin safety latch 41,11454 207 Side plate right, for hinged lifting bar 454 200, with pin safety latch 41,11454 209 Side plate internal, for hinged lifting bar 454 200, without pin safety latch 42,57

Hinged lifting bars

454 175

Article no. Product Dimensions Description Price €454 175 Container bumper 100x300x100mm S235JR 32,03

Container bumper

454 200

454 210

100

30048,5

48,5

100

4

360

970

382

636,

5

50

200

360

970

364,6

675,

5

50

200

454 202

454 201

454 205

454 203

140 300 03

454 202 01

454 201

454 205

454 203

140 300 03

454 202 01 454 207

454 209454 202

454 203

Stand 15062020


Article no. Product Dimensions Price €454 242 Insertable lifting bar, complete 50x969mm S355J2+N454 242 01 Insertable lifting bar 50x565mm S355J2+N454 243 Insertable lifting bar, complete 60x969mm S355J2+N454 243 01 Insertable lifting bar 60x565mm S355J2+N

Insertable lifting bars

- due to the slot system the lifting bar is easily interchangeable - only has to be exchanged if below a wear limit of 10% - can be used as anti-theft device - maximum carrying capacity 15/24 t - weight 17/22 kg - additionally the bar can be secured with a normal or personalized lock - can be upgraded since measurements are according to DIN - DEKRA tested


969

174

50/60

454 242 /-243

280

offen

geschlossen

442

454 244

20,5

22,5

M14

x1,5

454 244 1

22 18

SW17

Article no. Product Dimensions Price €454 244 Lock for insertable lifting bar M14x1,5mm 11,08454 244 1 Key for insertable lifting bar SW17 12,93

454 242 /-243

454 242 01/-243 01

454 244

NEW

Stand 15062020


Inse

rtab

le li

ftin

g ba

rs /

wea

r ga

uges

Article no. Product Description Price €454 091 Wear gauge V4A plate, for checking a wear limit of 10% 32,48

Wear gauge for container inspection (wear limit of 10%)

Article no. Product Description Price €454 092 Wear gauge V4A plate, for checking a wear limit of 5% 32,48

454 092

454 091

The wear gauge from 2mm V2A plate has 6 gap gauges for checking admis-sible wear limits of 5%/10% according to DIN from 2016-02, BG & DGUV:

- Lifting bars on roll-off containers & mobile compactors - Tipping bolts on skips - Lifting lugs on skips

The wear gauge enables a quick & secure check of the above named components within the framework of container inspections. Select the respective gap gauge according to the nominal dimension for the lifting bar, tipping bolt or lifting lug. If it is possible to slide the guage over the dia-meter of the tested part, it no longer conforms with safety requirements! 2 holes allow it to be stored in the company inspection file.

Utility model DE 20 2009 002 403.2 454 093

Wear gauge for container inspection according to DIN from 2016-02 (wear limit of 5%/10%)

Wear gauge for container inspection according to DIN from 2016-02 (wear limit of 5%)

The wear gauge from 2mm V2A plate has 6 gap gauges for checking ad-missible wear limits of 5% according to DIN from 2016-02, BG & DGUV:




The wear gauge from 2mm V2A plate has 6 gap gauges for checking ad-missible wear limits of 10%:




Article no. Product Description Price €454 093 Wear gauge V4A plate, for checking a wear limit of 5%/10% 32,48

NEW

Stand 15062020


Article no. Product Description Price €454 010 Rope hook for mounting with screws 26,93454 022 Rope hook for welding, forged 21,18454 021 Rope hook for welding, forged 13,05

Article no. Product Description Price €454 040 Rope pulley left, short 11,62454 045 Rope pulley right, short 11,62454 031 Rope pulley left, long 20,81454 032 Rope pulley right, long 20,81454 034 Rope pulley forged, S355J2 20,81454 033 1 Rope pulley 66,20

Rope pulleys & rope hooks

Article no. Product Description Price €454 170 Chain guide left, S355J2 30,89454 171 Chain guide right, S355J2 30,89454 177 Chain guide, complete primed, S355J2 268,84

Chain guides

900160100 100 270270220

233

5022

619

5

50

454 170

178 148

454 171

226

195

50

178 148

454 170

454 171

454 177

454 010 454 022

188

79 106

18

17

454 021

134

150

3040

65

8

454 034

16635

10671

454 031

140

4511

065

140

3070

454 040

4015

519

0

80

117

15

14

100

18

454 033 1

140

4912

879

NEW

Stand 15062020


82

68

32

454 271 /-272 /-273

95/110/140

45

Article no. Product Dimensions Description Price €454 260 Lifting lug 30x67x80mm forged, type DAUTEL 6,19454 285 Lifting lug 40x55x130mm forged 21,38454 275 Lifting lug 40x98x84mm forged 7,02454 276 Lifting lug 40x110x82mm welded 7,48454 270 Lifting lug 45x95x84mm forged, according to DIN 7,74454 271 Lifting lug 45x95x82mm welded 7,48454 272 Lifting lug 45x110x82mm welded 8,20454 273 Lifting lug 45x140x82mm welded 9,38

8432

66454 270

45

95

84

454 275

32

9866

40

8232

68 10

454 280Ch

ain

guid

es /

rope

pul

leys

& r

ope

hook

s / l

ifti

ng lu

gsLifting lugs

Article no. Product Dimensions Description Price €454 310 Side mounting for lifting lugs 40x1000x100x50mm forged lug, D=40mm 31,81454 300 Side mounting for lifting lugs 45x1000x100x50mm forged lug, D=45mm 32,83454 280 Plate 82x68x10mm for lifting lugs 2,86454 281 Plate 82x68x10mm for lifting lugs, d=46mm 3,83454 282 Plate 80x80x8mm for lifting lugs, d=46mm 3,65455 501 Lashing Point 80x80x40mm for lashing stacked skips, d=40mm 3,05

80

80

40 5

455 501

40

8232

68 10

454 281

46

80

80 8

46

454 282

82

68

32

454 276

110

40

80

454 260

44

30

6

67

130

80

80

454 285

120 6040

1000

84

550

40/4

510

0

100

100

66

40

8454 310 /-300

Stand 15062020


Tipping bar brackets

453 285

45

235205

415

42,5

Article no. Product Dimensions Description Price €453 284 1 Tipping bar bracket 245x184,5mm without base plate, in individual parts, bolt S355J2, DIN 30720 29,37453 284 Tipping bar bracket 245x200mm without base plate, in individual parts, bolt S355J2 29,37453 283 1 Tipping bar bracket 320x190,5x8mm bolt S355J2, DIN 30720 49,25453 283 Tipping bar bracket 320x206x8mm bolt S355J2 49,25453 282 1 Tipping bar bracket 320x220x8mm bolt S355J2, DIN 30720 51,92453 282 Tipping bar bracket 320x270x8mm bolt S355J2 51,92453 281 1 Tipping bar bracket 320x300x8mm bolt S355J2, DIN 30720 52,33453 281 Tipping bar bracket 320x345x8mm bolt S355J2 52,33

Article no. Product Dimensions Description Price €453 285 1 Tipping bar bracket 235x435,6mm without base plate, S355J2 26,93453 285 Tipping bar bracket 235x415mm without base plate, S355J2 26,93

453 285 1

235205 51

435,6

45

453 284 1

245205

10018

4,5

5045

453 283 1

320245205

10019

0,5

8

5045

453 282 1

320245205

100220

8

5045

453 281 1 50

320245205

100

300

8

45453 281

106

320245

345

205

70

8

45

453 282

320245205

70

106

45

270

8

453 283

320245205

70

106

45

206

8

453 284

245205

7045

106200

Stand 15062020


Article no. Product Dimensions Description Price €453 280 1 Tipping bar bracket 300x300x8mm bolt S355J2, DIN 30720 48,84453 280 Tipping bar bracket 300x340x8mm bolt S355J2 48,00453 279 1 Tipping bar bracket 245x331x8mm bolt S355J2, DIN 30720 46,17453 279 Tipping bar bracket 245x340x8mm bolt S355J2 46,17

45

245

453 300 453 302

45

280

Article no. Product Dimensions Description Price €453 290 1 Tipping bar bracket 245x636x8mm internal mounting, bolt S355J2, DIN 30720 98,50453 290 Tipping bar bracket 245x424x8mm internal mounting, bolt S355J2 66,09

Tipping bar brackets

Article no. Product Dimensions Description Price €453 300 Tipping bar shaft 45x245mm S355J2 7,83453 302 Tipping bar shaft 45x280mm S355J2 8,16

Tipp

ing

bar

brac

kets

453 280

300245205

340

8

240,4

100

45

453 279

245205

45

340

8

240,4

110

453 279 1

245205 8

234

331

100

45

453 280 1

300245205 8

211,8

300

100

45

453 290

8110

245205

45

300424

200453 290 1

8116,7

450636

200

245205

4550

Stand 15062020


Tripple tipping bar brackets

45

860

453 301

Article no. Product Dimensions Description Price €453 303 Tipping bar shaft 45x810mm S355J2 21,55453 301 Tipping bar shaft 45x860mm S355J2 24,52

45

810

453 303

Article no. Product Dimensions Description Price €453 320 1 Tripple tipping bar bracket 875x300x8mm Bolzen S355J2, DIN 30720-1 124,60453 320 Tripple tipping bar bracket 915x340x8mm Bolzen S355J2 129,96453 321 1 Tripple tipping bar bracket 810x300x8mm Bolzen S355J2, DIN 30720-2 125,17453 322 Tripple tipping bar bracket 810x299mm without base plate, bolt S355J2, DIN 30720-2 83,11453 321 Tripple tipping bar bracket 810x363x8mm Bolzen S355J2 134,86

453 320 1

875810

8

300

100

211,845

770

915860

453 320

8

240,4

340

100

45

820

453 321 1

810770 8

300

100

211,445

453 322

810770

299

100

211,445

810770

453 321

8

256

363

125

45

Stand 15062020


Article no. Product Dimensions Description Price €453 250 1 Tipping bar bracket 176x150x6mm for mini skips, bolt S355J2, DIN 30735 27,70453 250 Tipping bar bracket 225x155x6mm for mini skips, bolt S355J2 25,71453 251 Tipping bar bracket 285x190x6mm for mini skips, bolt S355J2, DIN 30735 36,94453 260 Tipping bar bracket 145x95x5mm for mini skips, bolt S355J2, type DAUTEL 16,54453 252 Tipping bar bracket 176x456x8mm for mini skips, internal mounting, bolt S355J2, DIN 30735 69,77

Tipping bar brackets for mini skips

Tripple tipping bar brackets

Article no. Product Dimensions Description Price €453 340 1 Tripple tipping bar bracket 810x643x8mm internal mounting, bolt S355J2, DIN 30720 226,75453 340 Tripple tipping bar bracket 860x424x8mm internal mounting, bolt S355J2 177,47

Trip

ple

tipp

ing

bar

brac

kets

/ ti

ppin

g ba

r br

acke

ts fo

r m

ini s

kips

453 252

176150

456

304

395

95

8

30453 260

145125

25

455

95

453 251

285150 68,8

6

190

30

453 250 1

176150 68,8

6

150

30453 250

225205 75

6

155

30

453 340 1

200

50

810770

450

8116,7

643

45

453 340

860820

8110

45

295424

192

Stand 15062020


Ratchet load binders

Cargo securing

Article no. Product Description Ketten-NG A B d WLL Price €455 000 Suspension link 1 strand, GK 8, according to EN-1677-4 6 110mm 60mm 13mm 1,6t 8,08455 010 Suspension link 1 strand, GK 8, according to EN-1677-4 8 110mm 60mm 16mm 2,12t 10,38455 020 Suspension link 1 strand, GK 8, according to EN-1677-4 10 135mm 75mm 18mm 3,15t 11,54455 030 Suspension link 1 strand, GK 8, according to EN-1677-4 13 160mm 90mm 22mm 5,3t 17,30455 040 Suspension link 1 strand, GK 8, according to EN-1677-4 16 180mm 100mm 26mm 8t 24,23

Article no. Product Description Ketten-NG A d WLL Price €455 100 Coupling GK 8 6 18mm 7,6mm 1,12t 9,37455 105 Coupling GK 8 8 23mm 10mm 2t 10,01455 110 Coupling GK 8 10 27mm 12,6mm 3,15t 13,06455 115 Coupling GK 8 13 34mm 16,7mm 5,3t 19,60455 120 Coupling GK 8 16 39mm 21mm 8t 28,30

Article no. Product Description Ketten-NG A B WLL Price €455 300 Clevis load hook GK 8, forged safety latch 6 26mm 15mm 1,12t 19,62455 305 Clevis load hook GK 8, forged safety latch 8 34mm 19mm 2t 24,23455 310 Clevis load hook GK 8, forged safety latch 10 40mm 25mm 3,15t 32,31

Article no. Product Description Ketten-NG A B WLL Price €455 330 Eye load hook GK 8, forged safety latch 6 25mm 16,5mm 1,12t 10,38455 335 Eye load hook GK 8, forged safety latch 8 33mm 19mm 2t 15,00455 340 Eye load hook GK 8, forged safety latch 10 40mm 26mm 3,15t 20,78455 345 Eye load hook GK 8, forged safety latch 13 51mm 33mm 5,3t 32,31455 350 Eye load hook GK 8, forged safety latch 16 55mm 40mm 8t 58,88

Article no. Product Description Ketten-NG A B d WLL Price €455 230 Clevis shackle GK 8 10 21mm 36mm 16mm 3,15t 73,95455 240 Clevis shackle GK 8 13 27mm 49mm 20mm 5,3t 84,83455 250 Clevis shackle GK 8 16 33mm 56mm 24mm 8t 113,11

610/735

455 740 /-750

A

B

d

455 000 /-010 /-020 455 030 /-040

A

d455 100 /-105 /-110455 115 /-120

A

B455 300 /-305 /-310

A

B

455 330 /-335 /-340 455 345 /-350

B

Ad

455 230 /-240 /-250

Article no. Product Description NG zul. Zurrkraft Bruchlast min L min/max d Quantity scale Price €/item455 740 Ratchet load binder with 2 hooks, red 10 6.300daN 12.600daN 610/735mm 20mm 28,73455 750 Ratchet load binder with 2 hooks, red 13 10.600daN 21.200daN 610/735mm 26mm 32,83455 700 Ratchet load binder red 8 4.000daN 8.000daN 320/480mm 20mm 24,62455 710 Ratchet load binder red 10 6.300daN 12.600daN 340/520mm 20mm 1-4/from 5 24,62/20,52*455 713 Ratchet load binder red, foldable handle 10 6.300daN 12.600daN 340/520mm 20mm 50,03455 710 1 Ratchet load binder galvanized 10 6.300daN 12.600daN 340/520mm 20mm 26,68455 720 Ratchet load binder red 13 10.600daN 21.200daN 360/530mm 26mm 1-4/from 5 26,68/22,57*455 720 1 Ratchet load binder galvanized 13 10.600daN 21.200daN 360/530mm 26mm 28,00

d

- shortening hooks with safety fastening on both sides - locking pin according to EN 12195-3

- eye according to EN 12195-3 - anti-twist

L255d

353

455 700 /-710 /-710 1 /-720 /-720 1 455 713

327

dL

255

Stand 15062020


- high-strength, straight form - with threaded pin - maximum working load limit (WLL) & nomi-nal size imprinted - minimum 5-way safety - bracket hot-dip galvanized, painted pin

- high-strength, curved form - with pin, nut & cotter - maximum working load limit (WLL) & nomi-nal size imprinted - minimum 5-way safety - bracket hot-dip galvanized, painted pin

Ratc

het

load

bin

ders

/ ca

rgo

secu

ring

D2

A

D1

C

D2

A

D1

C

Cargo securing

Article no. Product NG WLL A C D1 D2 Price €455 600 Shackle 5/8” 3,25t 51mm 27mm 20mm 16mm 6,93455 605 Shackle 3/4” 4,75t 60mm 32mm 22mm 19mm 7,50455 610 Shackle 7/8” 6,5t 71mm 36mm 27mm 22mm 12,69455 615 Shackle 1” 8,5t 81mm 43mm 28mm 25mm 13,84

Article no. Product Description NG A/B R DxL WLL Price €455 450 Shortening hook GK 8, with clevis & safety latch 6 8mm 51mm 7,5x17,5mm 1,12t 19,15455 455 Shortening hook GK 8, with clevis & safety latch 8 10mm 65mm 10x13mm 2t 19,46455 460 Shortening hook GK 8, with clevis & safety latch 10 13mm 80mm 13x31,5mm 3,15t 26,10455 465 Shortening hook GK 8, with clevis & safety latch 13 17mm 105mm 16x42mm 5,3t 49,16

Article no. Product Description NG A/B C DxL WLL Price €455 405 Shortening cleat GK 8, with clevis & safety latch 8 9,5mm 10mm 10x22,5mm 2t 46,16455 410 Shortening cleat GK 8, with clevis & safety latch 10 12mm 14,5mm 13x31,5mm 3,15t 56,53455 415 Shortening cleat GK 8, with clevis & safety latch 13 16mm 18mm 16x42mm 5,3t 78,46

Article no. Product Description A B C D WLL Price €455 565 Welding hook GK 8 30,5mm 24mm 129mm 106mm 3t 38,99455 570 Welding hook GK 8 34,5mm 30mm 171mm 136mm 5t 43,09455 575 Welding hook GK 8 34,5mm 39mm 177mm 140mm 8t 99,22

455 600 /-605 /-610 /-615455 630 /-635 /-640 /-645 /-650 /-655

B

C

A

D

455 565 /-570 /-575

C

BD

A

455 405 /-410 /-415

R

d B

A

455 450 /-455455 460 /-465

A

B

455 355 /-360

B

FE

455 535 /-340

Article no. Product Description NG A B WLL Price €455 355 Lifting eye GK 8, with clevis, forged safety latch 13 57mm 65mm 5,3t 119,63455 360 Lifting eye GK 8, with clevis, forged safety latch 16 57mm 65mm 8t 172,92

Article no. Product Description NG B E F WLL Price €455 535 Lifting link GK 8, for mini skip, with clevis 10 49mm 126mm 95mm 3,15t 43,09455 540 Lifting link GK 8, for mini skip, with clevis 13 60mm 158,5mm 120mm 5,3t 54,22

Article no. Product NG WLL A C D1 D2 Price €455 630 Shackle, curved 3/8” 1t 26mm 16mm 12mm 10mm 3,11455 635 Shackle, curved 5/8” 3,25t 43mm 27mm 20mm 16mm 8,08455 640 Shackle, curved 3/4” 4,75t 51mm 32mm 22mm 19mm 9,49455 645 Shackle, curved 7/8” 6,5t 58mm 36mm 27mm 22mm 13,84455 650 Shackle, curved 1” 8,5t 68mm 43mm 28mm 25mm 16,27455 655 Shackle, curved 1 1/8” 9,5t 74mm 46mm 33mm 29mm 21,93

Stand 15062020


455 981

Article no. Product Description Price €455 830 Test badge for lashing chain GK 8 2,31455 831 Test badge for lashing chain GK 8, lashing force 2,31

Article no. Product Dimensions Description Price €455 981 Anti-slip mat 125x1000x8mm slip-friction coefficient µ=0,6 2,80455 982 Anti-slip mat 125x10000x8mm slip-friction coefficient µ=0,6 27,08

Anti-slip mats

Article no. Product Description B NG t WLL Price €/meter455 805 Lashing chain EN 818-2 21,6 6 18 1,12t 9,23455 810 Lashing chain EN 818-2 28,8 8 24 2t 12,24455 815 Lashing chain EN 818-2 36 10 30 3,15t 16,85455 820 Lashing chain EN 818-2 46,8 13 39 5,3t 27,19455 825 Lashing chain EN 818-2 57,6 16 48 8t 47,51

- chains tested, non-calibrated - short linked, corrosion-resistant surface - silver-coloured - chains for fi tting in container-lashing

455 805 /-810 /-815 /-820 /-825

t

Article no. Product Description Price €/strand455 910 Container lashing maximum effective length 3,1m/strand 140,04455 920 Container lashing maximum effective length 2,2m/strand 131,84

Container lashing & lashing chains

- GK 8, chain D=10mm - rated load LC 6300 daN, (per pair 12.600 daN) - shortening claw with safety latch - eye load hook with jaw width 31mm - lashing options:

B NG

455 830

10

455 831

10

Stand 15062020


Article no. Product Dimensions WLL Description Price €453 413 Lashing hook 66,5x150x39mm 2,5t forged, foldable 9,60453 414 Lashing hook 72x125x40mm 3t forged, foldable 9,20455 501 Lashing Point 80x80x40mm for lashing stacked skips, d=40mm 3,05

Cont

aine

r la

shin

g &

lash

ing

chai

ns /

anti

-slip

mat

s / l

ifti

ng p

oint

s &

lash

ing

eyeLifting points & lashing eye

80

80

40 5

455 501

40

453 425

60111,5

8833 11

25

10585

32

453 400

20

7453 412

94

89 46

30 29

Article no. Product Description A B C D WLL Price €455 500 1 Lifting point with spring, for welding 45 43 60 17 3,15t 6,80455 510 1 Lifting point with spring, for welding 55 49 76 22 5,3t 12,50455 520 1 Lifting point with spring, for welding 69 66 88 26,5 8t 19,00455 525 1 Lifting point with spring, for welding 97 90 120 34 15t 42,00

95

90

453 411

34

30 35

150

453 413

66,5

39 19

453 414

125

72

1840

Article no. Product Description WLL Price €455 555 1 Load ring elbow connection, for welding, swivel range 270° 7t 44,00

455 555 1

120

24

76

64

84

180

Article no. Product Dimensions WLL Description Price €453 400 Lashing eye 105x105x20mm 1t galvanized, for wooden floors, with spring & drain hole 6,11453 412 Lashing eye 89x94x29mm 2,5t black, with drain hole 7,80453 411 Lashing eye 90x95x35mm 6t black, with drain hole 9,00453 425 Lashing eye 33x109x60mm 2,5t forged 15,69

455 500 1 /-510 1 /-520 1 /-525 1

DA

BC

NEW

NEW

NEW

Stand 15062020


Article no. Product Dimensions Description Price €457 501 Ratchet M20x200x305mm handle L=160mm, for compactors, type LOTUS, galvanized 100,06457 510 Ratchet M24x255x305mm handle L=160mm, for compactors, galvanized 106,58457 500 Ratchet M24x255x365mm handle L=197mm, for compactors, galvanized 113,11457 496 Ratchet M24x255x560mm handle L=360mm, for swap container, type HÜFFERMANN, galvanized 248,59457 508 Ratchet M30x255x365mm handle L=197mm, for compactors, galvanized 113,11457 499 Ratchet M30x650x365mm handle L=197mm, for stationary compactors, galvanized 277,81457 509 Ratchet M36x295x365mm handle L=197mm, for compactors, galvanized 171,83457 502 Ratchet M48x355x365mm handle L=197mm, for stationary compactors, galvanized 246,24

Article no. Product Dimensions Description Price €457 509 05 Ratchet with clevises M36x295x500mm handle L=332mm, with clevises 457 509 101 /-509 111, galvanized 304,52457 495 Ratchet with clevises TR48x440x500mm handle L=332mm, with clevises with trapezoidal thread, galvanized 709,99

1313 27

30

12

104

457 515

Article no. Product Dimensions Description Price €457 513 Threaded rod M24x260mm left-hand thread 4,06457 514 Threaded rod M24x260mm right-hand thread 4,06457 571 Threaded rod M30x260mm left-hand thread 6,93457 572 Threaded rod M30x260mm right-hand thread 6,93457 576 Threaded rod M36x260mm left-hand thread 13,60457 577 Threaded rod M36x260mm right-hand thread 13,60457 578 Threaded rod M48x260mm left-hand thread 27,93457 579 Threaded rod M48x260mm right-hand thread 27,93457 515 Clevis head 104x30mm 3,16457 508 10 Hook 280x37mm galvanized 43,44

280

64 36

457 508 10

t=37

100260/300/380

150/180/210 M24

/30/

36/4

8

457 513 /-514 /-571 /-572 /-576 /-577 /-578 /-579

457 501

200

305

160

M20

457 51016

0

305

255M24

457 500

255

365

197

M24

457 496

255

560

360

M24

457 508

255

365

197

M30

457 499

650

365

197

M30

457 50919

7

365

295327

M36

457 502

197

365

355387

M48

457 509 05

295min 855 - max 1070

332 50

0

440min 672 - max 992

332 50

0

457 495

Ratchets

Threaded rods

NEW

Stand 15062020


M24

134213

457 511 /-512

70

33

M20

100165

457 535 /-536

52

24

370330

205

75

M30 46

M30457 555 /-556

210190

110

62

M20 23

M16457 531 /-532

268256

155

79M

24

14

12457 516 /-517

M36

160265

457 542 /-54395

43

M30

135215

457 538 /-539

71

30

M48

185

335

457 544 /-546

133

58

290260

160

60

M30 34

M24457 533 /-534

457 528 /-529

240215

125

38

M24 29

M20

465428

250

100

M36 52

457 509 101 /-111M36

Article no. Product Dimensions Description Price €457 531 Clevis M20x210mm left-hand thread, galvanized, with bolt & nuts 16,42457 532 Clevis M20x210mm right-hand thread, galvanized, with bolt & nuts 16,42457 528 Clevis M24x240mm left-hand thread, galvanized, forged, with bolt & nuts 14,68457 529 Clevis M24x240mm right-hand thread, galvanized, forged, with bolt & nuts 14,68457 516 Clevis M24x268mm left-hand thread, galvanized 12,31457 517 Clevis M24x268mm right-hand thread, galvanized 12,31457 540 Clevis M24x280mm left-hand thread, galvanized, forged, with locking lug, bolt & nut 36,94457 541 Clevis M24x280mm right-hand thread, galvanized, forged, with locking lug, bolt & nuts 36,94457 533 Clevis M30x290mm left-hand thread, galvanized, with bolt & nuts 20,67457 534 Clevis M30x290mm right-hand thread, galvanized, with bolt & nuts 20,67457 555 Clevis M30x370mm left-hand thread, galvanized, forged, with locking lug, bolt & nuts 37,84457 556 Clevis M30x370mm right-hand thread, galvanized, forged, with locking lug, bolt & nuts 37,84457 509 101 Clevis M36x465mm left-hand thread, galvanized, forged, with bolt & nuts 63,08457 509 111 Clevis M36x465mm right-hand thread, galvanized, forged, with bolt & nuts 63,08

Article no. Product Dimensions Description Price €457 535 Threaded eye M20x165mm d=24mm, left-hand thread, galvanized 8,57457 536 Threaded eye M20x165mm d=24mm, right-hand thread, galvanized 8,57457 511 Threaded eye M24x213mm d=33mm, left-hand thread, galvanized 11,29457 512 Threaded eye M24x213mm d=33mm, right-hand thread, galvanized 11,29457 538 Threaded eye M30x215mm d=30mm, left-hand thread, galvanized 19,36457 539 Threaded eye M30x215mm d=30mm, right-hand thread, galvanized 19,36457 542 Threaded eye M36x265mm d=43mm, left-hand thread, galvanized 21,19457 543 Threaded eye M36x265mm d=43mm, right-hand thread, galvanized 21,19457 544 Threaded eye M48x335mm d=58mm, left-hand thread, galvanized 40,01457 545 Threaded eye M48x335mm d=58mm, right-hand thread, galvanized 40,01

280255

150

50

M24 32

M24457 540 /-541

Ratc

hets

/ th

read

ed r

ods

/ thr

eade

d ey

es /

clev

isesThreaded eyes / clevises

Stand 15062020


Article no. Product Dimensions Description Price €453 244 01 Coupling sleeve 1” black 6,88453 244 05 Storz coupling 1” outer thread 7,98453 244 04 Storz coupling 1” inner thread 7,73453 244 03 Sealing ring 1” 0,97453 244 02 Plug 1” galvanized 4,22453 246 01 Threaded pipe 2” L=200mm, galvanized 7,39453 246 03 Ball valve 2” brass thread, SW65 33,86453 246 05 Storz coupling 2” outer thread 9,75453 246 04 Storz coupling 2” inner thread 9,65453 246 02 Plug 2” galvanized 5,22

Water outlet

Foam rubber seals

Article no. Product Description Price €459 143 Adhesive kit for EPDM glue & primer, 30g, not a stock item, is to be applied in thin layers on both ends 60,90

Article no. Product Dimensions Description Price €/meter459 119 Foam rubber seal D=20mm round, 25m bundle 3,03459 120 Foam rubber seal D=30mm round, 20m bundle 7,15459 126 Foam rubber seal 10x60mm square, 25m bundle 7,19459 114 Foam rubber seal 12x20mm square, 50m bundle 2,55459 128 01 Foam rubber seal 15x15mm square, 25m bundle 2,83459 102 Foam rubber seal 15x20mm square, 25m bundle 3,03459 115 Foam rubber seal 15x30mm square, 25m bundle 4,34459 104 Foam rubber seal 15x40mm square, 25m bundle 5,64459 104 1 Foam rubber seal 15x50mm square, 15m bundle 6,31459 101 Foam rubber seal 20x20mm square, 25m bundle 3,89459 127 Foam rubber seal 20x25mm square, 25m bundle 5,06459 112 Foam rubber seal 20x30mm square, 25m bundle 5,32459 112 1 Foam rubber seal 20x35mm square, 25m bundle 6,90459 106 Foam rubber seal 20x40mm square, 25m bundle 7,86459 117 Foam rubber seal 20x45mm square, 25m bundle 8,73459 103 Foam rubber seal 20x50mm square, 25m bundle 10,22459 107 Foam rubber seal 25x25mm square, 25m bundle 6,11459 123 Foam rubber seal 25x35mm square, 25m bundle 8,49459 125 Foam rubber seal 25x40mm square, 25m bundle 9,90459 111 Foam rubber seal 25x50mm square, 15m bundle 13,10459 108 Foam rubber seal 30x30mm square, 20m bundle 7,40459 118 Foam rubber seal 30x35mm square, 15m bundle 9,95459 110 1 Foam rubber seal 30x40mm square, 15m bundle 13,59459 110 Foam rubber seal 30x45mm square, 15m bundle 14,06459 116 Foam rubber seal 40x40mm square, 10m bundle 17,10

453 244 01

453 244 03

453 244 02

453 244 05

453 244 04

453 246 03

453 246 02

453 246 01

453 246 05

453 246 04

D B

A

NEWNEW

Stand 15062020


Seals / guide profiles for seals

462 212

125

125

2,5

1823

500/2200

21822

15

462 213 /-210

502

10

462 215 4,5

1100250 250 250 250 50

1100

10

9

2427

462 214 5,5

50 250 250 250 250 50

Article no. Product Dimensions Description Price €/meter459 209 Composite sealing profile 24x14,6mm self-clamping, 25m bundle, deformable max. 10mm 7,40

Article no. Product Dimensions Description Price €462 215 Anchoring plate 1100x10x2mm galvanized, for seal 459 133 7,61

Article no. Product Dimensions Description Price €462 212 U-profile 15x23x2,5mm 90° elbow, S355J2, for seal 459 113 13,72462 213 U-profile 500x22x15x2mm for seal 459 113 3,67462 210 U-profile 2200x22x15x2mm for seal 459 113 10,21

Article no. Product Dimensions Description Price €/meter459 113 Seal for compactors 21,6x33,4mm 20m bundle, for 462 210 /-212 /-213 11,07

Article no. Product Dimensions Description Price €/meter459 133 Seal for container doors 18x33mm 25m bundle, for 462 215 6,31

Article no. Product Dimensions Description Price €462 214 Guide profile 1100x27x9mm steel, galvanized, for seal 459 132 8,73

Article no. Product Dimensions Description Price €/meter459 132 Seal for container doors 20x30mm 30m bundle, for 462 214 6,26

Wat

er o

utle

t / f

oam

rub

ber

seal

s / s

eals

/ gu

ide

profi

les

for

seal

s

15

920

30

459 132

459 113

21,6

33,4

18

18 12

33

18

459 133

459 209

18,7

10,7

14,6

Stand 15062020


Stickers

Article no. Product Dimensions Items/sheet Quantity scale Price €/item459 220 1 PVC base sticker “Prüfung gemäß § 14 BetrSichV” 210x150mm 1 1-50/51-199/from 200 0,98/0,84*/0,76*459 222 1 PVC base sticker “Prüfung gemäß § 14 BetrSichV” 105x95mm 6 6-48/54-204/from 210 0,69/0,60*/0,54*459 255 1 PVC base sticker “Prüfung gemäß § 14 BetrSichV” mit Logo 110x148mm 4 on request459 221 1 PVC base sticker “Prüfung gemäß § 14 BetrSichV” 40x95mm 15 15-60/75-195/from 210 0,44/0,36*/0,25*459 226 PVC base sticker “nächste Prüfung gemäß UVV” 40x95mm 15 15-60/75-195/from 210 0,53/0,42*/0,30*459 243 PVC inspection sticker “perennial” D=75mm 6 6-48/54-204/from 210 1,20/1,09*/0,92*459 242 PVC inspection sticker “perennial” D=30mm 48 48/96-192/from 240 0,39/0,33*/0,29*459 230 PVC inspection sticker “2020” D=75mm 6 6-48/54-204/from 210 0,51/0,44*/0,40*459 239 PVC inspection sticker “2020” D=30mm 48 48/96-192/from 240 0,30/0,24*/0,19*459 233 PVC inspection sticker “2021” D=75mm 6 6-48/54-204/from 210 0,51/0,44*/0,40*459 237 PVC inspection sticker “2021” D=30mm 48 48/96-192/from 240 0,30/0,24*/0,19*459 234 PVC inspection sticker “2022” D=75mm 6 6-48/54-204/from 210 0,51/0,44*/0,40*459 232 PVC inspection sticker “2022” D=30mm 48 48/96-192/from 240 0,30/0,24*/0,19*459 231 PVC inspection sticker “2023” D=75mm 6 6-48/54-204/from 210 0,51/0,44*/0,40*459 238 PVC inspection sticker “2023” D=30mm 48 48/96-192/from 240 0,30/0,24*/0,19*

459 243 459 242 459 239459 230 459 237459 233 459 232459 234 459 238459 231

459 241 1459 240

Schutzausrüstung

Ladung

Abrollbehälter

Fahrzeug

Ladeort

Vor der Abfahrt

Vor dem Abrollen des Behälters

Vor dem Kippvorgang

Schutzausrüstung

Ladung

Absetzbehälter

Fahrzeug

Ladeort

Vor der Abfahrt

Vor dem Absetzen des Behälters

Vor dem Kippvorgang

459 222 1

459 220 1

459 221 1 459 226

459 255 1

459 200 1459 200

459 200 2

Article no. Product Dimensions Items/sheet Quantity scale Price €/item459 240 PVC sticker “Warnhinweise für Abrollcontainer” 210x297mm 1 1-50/51-199/from 200 2,20/1,85*/1,63*459 241 1 PVC sticker “Warnhinweise für Absetzcontainer” 210x297mm 1 1-50/51-199/from 200 2,20/1,85*/1,63*459 200 2 Type label aluminum sticker for roll-off containers 194x97mm 3 3-48/51-192/from 195 6,36/5,27*/3,61*459 200 Type label aluminum sticker for skips 95x65mm 8 8-48/56-192/from 200 1,20/1,07*/0,96*459 200 1 Type label aluminum plate for skips 100x70mm 1 1-50/51-99/from 100 3,69/2,93*/2,61*

NEW

NEWNEW

NEWNEW

Stickers according to customer specification on request

Stand 15062020


Article no. Product Dimensions Items/sheet Quantity scale Price €/item459 284 PVC sticker "Schadstoffhaltige Abfälle" 297x210mm 1 1-50/51-199/from 200 3,33/2,90*/2,65*459 206 PVC sticker “Im Interesse des Umweltschutzes” 297x210mm 1 1-50/51-199/from 200 3,33/2,90*/2,65*459 207 PVC sticker “Nur bis zum Rand füllen!” D=200mm 1 1-50/51-199/from 200 4,48/4,04*/3,78*459 202 PVC sticker “Greifer” D=200mm 1 1-50/51-199/from 200 4,48/4,04*/3,78*459 210 1 PVC sticker "Deckel ist federbelastet" 105x95mm 6 6-48/54-204/from 210 0,69/0,60*/0,54*459 210 PVC sticker “Deckel ist federbelastet” 210x150mm 2 2-50/52-198/from 200 0,97/0,77*/0,68*459 282 PVC sticker "Quetschgefahr" 210x150mm 2 2-50/52-198/from 200 1,58/1,36*/1,20*459 248 PVC sticker “5880 daN” 210x150mm 2 2-50/52-198/from 200 3,05/2,50*/2,18*459 249 PVC sticker “2450 daN” 210x150mm 2 2-50/52-198/from 200 3,05/2,50*/2,18*459 228 PVC sticker “Winde-Dachverschluss öffnen!” 210x150mm 2 2-50/52-198/from 200 1,64/1,43*/1,29*459 229 PVC sticker “Hebezeug-Deckelverschluss öffnen!” 210x150mm 2 2-50/52-198/from 200 1,74/1,51*/1,37*459 211 PVC sticker “Vor öffnen der Türen” 210x150mm 2 2-50/52-198/from 200 1,06/0,91*/0,82*459 208 PVC sticker “aus dem Schwenkbereich der Tür treten” 210x150mm 2 2-50/52-198/from 200 1,06/0,91*/0,82*

Stickers

Stic

kers

459 210 1

459 284

459 248

459 249

459 210

459 282

459 211

459 208459 229

459 207

459 202

459 228

459 206

NEWNEW

NEW

Stand 15062020


459 216

Stickers

Article no. Product Dimensions Items/sheet Quantity scale Price €/item459 216 PVC sticker “Kurzbedinungsanleitung für Müllpressen” 210x297mm 1 1-50/51-199/from 200 2,39/1,91*/1,74*459 214 PVC sticker “Vorsicht! Quetschgefahr” 210x297mm 1 1-50/51-199/from 200 2,39/1,91*/1,74*459 212 PVC sticker “Niemals in den Befülltrichter greifen” 210x150mm 2 2-50/52-198/from 200 1,58/1,36*/1,20*459 213 PVC sticker “Netzstecker ziehen” 210x150mm 2 2-50/52-198/from 200 1,58/1,36*/1,20*459 227 PVC sticker “Pressenraum bei jeder Leerung reinigen” 297x210mm 1 1-50/51-199/from 200 3,33/2,90*/2,65*459 215 PVC sticker “Pressenraum 1 mal wöchentlich reinigen” 297x210mm 1 1-50/51-199/from 200 2,39/1,91*/1,74*459 219 PVC sticker “NOT-AUS” 90x90mm 6 6-48/54-210/from 216 0,97/0,84*/0,76*459 201 Type label aluminum sticker for compactors 194x97mm 3 3-48/51-192/from 195 6,36/5,27*/3,61*459 257 PVC sticker “Nach Entleerung Türverriegelung sichern!” 210x150mm 2 1,36459 217 PVC sticker “Hakenbügel nur für Rangierzwecke” 297x210mm 1 1-50/51-199/from 200 2,39/1,91*/1,74*

459 217459 215

459 214

459 227

459 219

459 201

459 213

459 257

459 212

Stickers according to customer specification on request

Stand 15062020


Stickers

Stic

kers

Article no. Product Dimensions Items/sheet Quantity scale Price €/item660 051 PVC sticker “Nicht in die Schüttung greifen” 210x75mm 4 4-40/44-200/from 204 2,03/1,81*/1,57*660 052 PVC sticker “Nicht hinter den Schwenkarm treten” 210x75mm 4 4-40/44-200/from 204 2,03/1,81*/1,57*660 041 PVC sticker “Nicht in die Schüttung fassen” D=90mm 6 6-48/54-204/from 210 2,03/1,81*/1,57*660 040 PVC sticker “Achtung Schüttungsarm” D=90mm 6 6-48/54-204/from 210 2,03/1,81*/1,57*660 050 PVC sticker “Achtung! §45 Abs. 3 UVV für Fahrzeuge” 148x105mm 4 4-40/44-200/from 204 2,03/1,81*/1,57*459 203 PVC sticker “Aufsteigen verboten” D=200mm 1 1-50/51-199/from 200 4,48/4,04*/3,78*459 218 PVC sticker “Sicherungskette lösen/wieder einhängen” 297x210mm 1 1-50/51-199/from 200 2,20/2,03*/1,73*660 053 PVC sticker “Hydrauliköl/Ölstand” 195x145mm 2 2-50/52-198/from 200 2,20/2,03*/1,73*459 283 PVC sticker "Zufahrt freihalten!" 210x95mm 3 3-48/51-192/from 195 1,58/1,36*/1,20*459 205 PVC sticker “Bekleben verboten!” 210x150mm 2 2-50/52-198/from 200 1,06/0,91*/0,82*

Article no. Product Dimensions Items/sheet Quantity scale Price €/item660 042 PVC sticker “Achtung Seitenlader!” 850x600mm 1 1-10/11-20/from 21 32,62/27,96*/22,13*

660 042

459 203

660 051

660 052

660 040660 041

459 283

660 053

459 218660 050 459 205

Stand 15062020


Article no. Product Dimensions Description Quantity scale Price €/Satz459 070 Chevron marking 705x141mm DIN67520, retroreflective, 4x left, 4x

right, 10 year guarantee1-9/10-49/from

5030,45/28,28*/23,93*

Article no. Product Dimensions Description Quantity scale Price €/Satz459 073 Chevron marking 705x141mm DIN67520, retroreflective, 4x left, 4x

right, 5 year guarantee1-9/10-49/from

5020,66/18,49*/16,31*

Article no. Product Dimensions Description Price €/Satz459 075 Chevron marking for vehicles 9000x141mm DIN67520, retroreflective, edge protection film, 1 roll left, 1

roll right182,71*

Chevron markings

Chevron marking for vehicles

141

705

459 070 459 100

150

710

141

705

459 073

141

9000

459 075

Article no. Product Dimensions Description Price €/item459 100 Magnetic foil 710x150x0,9mm white 11,52

Stand 15062020


Chev

ron

mar

king

s / s

ervi

ce c

heck

list

for

cont

aine

rs

This service checklist can be send to you free of charge by email or fax on request

Service checklist for containers

Roll-off containers

Wear / visual inspection (condition, welding seams, operation)

oknicht

ok

Lifting bar / Hinged lifting bar

Rope pulleys

Chain guides

U- / I-frame

Frame profile

C-profile

Rollers / shafts / brackets

Doors

Hinges

Door lock

Flap lock

Locking shaft / locking lever

Door lock pin

Container wall

Container floor

Steel lid with bearing

Jack with bearing

Lid hydraulic with bearing

Ladder / steps

Ladder / steps, anti-slip tread

Tarpaulin hooks

Tarpaulin with rope / net

Roll-on tarpaulin with fittings

Lid / door seal

Approval

Manufacturer

Type

Serial no.

Year of construction

Internal container no.

Next Inspection

Descriptionen

Company

Cost centre

Place, date Signature

Skips

Wear / visual inspection (condition, welding seams, operation)

oknich ok

Lifting lugs / side mounting

Frame profile

Tipping bar

Flap with bearing / hinges

Lid with bearing

Counter spring system

Locks

Lid detent

Container wall

Container floor

Jack with bearing

Lid hydraulic with bearing

Tarpaulin hooks

Tarpaulin with rope / net

Roll-on tarpaulin with fittings

Visual inspection of stickers / plates

Hazard signs, legibility

Operating manual, legibility

Type label, legibility

Next Inspection

Chevron marking condition

Paintwork condition

Lid seal

Approval

Stand 15062020


Signature, company stamp Name in capital letters

Payment 10 days 2% discount, 30 days nettoFor further terms of payment & delivery see the general terms & conditions

Order form

Invoice Address

Contact person

Function

Phone

Fax

E-mail

Total price €, netto

Total price €, incl. 19% VAT

Delivery Address

Date

Order no.

Additional information

Head office Richard-Wagner-Straße 51 | D-10585 BerlinPhone 0049 (0)30 2000 578 - 80

Sales 0049 (0)30 2000 578 - 81 / - 83 / - 85Fax 0049 (0)30 2000 578 - 99

E-mail [email protected] | www.rewald.eu

Article no. Product Amount Price per unit € Total price €

Over-Night Express Next Day Express Standard Delivery

Stand 15062020


Ord

er fo

rm /

gene

ral t

erm

s &

con

diti

ons

REW

ALD

Gm

bHGeneral terms & conditions REWALD GmbH

1. The customer declares himself in agreement with our standard terms and conditions when placing an order. Failure of the customer to reveal any particular terms of business on their side does not in any way imply our consent to them. In particular, the delivery or provision of services does not constitute implied acceptance of the customer’s terms and conditions. Alterations, supplementary agreements and additions to the Standard Terms of Business require our written con-firmation.

2. All offers are subject to change and are non-binding. All documents relating to these offers, including figures, drawings, weights or dimen-sions and including any other technical information and references to technical standards and designs merely indicate the object of the agreement and are subject to written confirmation of technical pro-perties. All prices are quoted for deliveries ex-factory including loa-ding in factory and excluding standard packaging and VAT. Our offers are based on the latest technical developments, the relevant accident prevention regulations, safety regulations etc at the time of making the offer.

3. For content and scope of the contract our written confirmation of the order is definitive. Supplementary agreements, additions etc re-quire our written confirmation.

4. We only accept prepayment. Our request minimum value is 50 €.

5. In the event that after closing of contract we become aware of cir-cumstances which substantially bring the credit-worthiness of the customer into question, or if payment terms are not met, we are en-titled to demand at our discretion payment in advance of any liabili-ties arising out of the business relationship or to ask for appropriate securities.

6. If circumstances arising out of our control, including but not limited to operational disturbances, strikes or lock-outs, freight disruption and any other unforeseeable shortages which occur with our sup-pliers, and which cause the failure or delay of consignments or ser-vices, we reserve the right to deliver at a later date or to withdraw wholly or partly from the contract without the customer having the right to claim damages. In the event of a delay in delivery or services the customer is entitled to withdraw from the contract after the ex-piry of a reasonably extended deadline of at least 2 weeks. Any wi-thdrawal from contract must take place through written declaration.

7. All shipments are insured. A statement of any damages or shorta-ges to the consignment must be drawn up immediately after receipt. Liability for the risk of accidental damage passes to the purchaser when the consignment is handed over to the freight carrier, but at the latest when the consignment leaves the warehouse. Specific shipping instructions of the customer are only binding if agreed to in writing. Otherwise delivery will be made as we deem best and under exclusi-on of any liability for the choice of mode of shipment. Shipment takes place at the expense of the buyer. For orders within Germany with a minimum net value of 770 Euro freight delivery will not be charged.

8. The following conditions apply to our warranty and liability for de-fects in delivery or service, including incorrect delivery or performan-ce: any claims must be made in writing within one week of receipt of goods or services. In the event of justified complaint, excluding the absence of guaranteed qualities, we reserve the right to remedy the defective delivery or service within a reasonable space of time. Whe-re applicable, we may recall the defective goods and supply a repla-cement; we will not assume responsibility for the costs of assembly, disassembly, or installation. The customer is obliged to allow us the opportunity for rectification during normal working hours by prior agreement.

9. We retain title to all goods supplied pending full and complete pay-ment and until all present and future claims arising out of the bu-siness relationship have been met. If the customer acquires sole or shared ownership on the basis of the joining, combining, mixing or processing of our consignment (with other consignments) then we shall have ownership to the ratio of the value of our consignment in relation to the other goods with which it is joined, combined or mixed. Any treatment or processing is covered according to Paragraph 950 BGB without any obligation on our part. Furthermore is any resale prohibited.

10. Only goods specifically listed on the delivery note can be returned. Goods which have been damaged are non-returnable. The cost and risks of return freighting of the returned goods will be borne by the customer. Returned goods will be refunded less a deduction of 20% of the purchase price.

11. The relinquishing of claims against the customer which are due to us in the business relationship is excluded.

12. We will only be liable for deliberate or gross negligence of our agents and senior management, or vicarious agents and assistants. Otherwise any claims for damages arising from fault during the cont-ract negotiations, from actual breach of contract, arising out of a pu-nishable act, or contractual rights ( such as consultation or informa-tion about qualities, applications, service requirements etc) are ruled out. In particular we will only be liable for consultations for which a separate payment was agreed.

13. Place of dispatch for all shipments and payments is Berlin, Ger-many. Sole place of jurisdiction is Amtsgericht Berlin-Charlottenburg.

14. The contractual relationship is governed by German law. The ap-plication of the uniform law governing the international purchase of movable objects is excluded.

15. Should any of the above stated provisions be either fully or in part invalid, the validity of the remaining provisions of contract shall not in any way be affected.

Prices marked with * cannot be reduced further.

Further catalogues

Office Richard-Wagner-Straße 51 | 10585 Berlin | Germany

Warehouse Hafenstraße 1 | 16727 Velten | Germany

Head office 0049 (0)30 2000 578 - 80

Sales 0049 (0)30 2000 578 - 81 / - 83 / - 85

Fax 0049 (0)30 2000 578 - 99

E-mail [email protected]

Internet www.rewald.eu

components for roll-off containers & skips

Documents