common rail system (hp3) for mitsubishi triton triton b.pdf · 00400554e common rail system (hp3)...
TRANSCRIPT
00400554E
Common Rail System (HP3)for MITSUBISHI TRITON 4D56/4M41 Engine
DENSO INTERNATIONAL THAILAND CO., LTD
© 2005 DENSO CORPORATIONAll Rights Reserved. This book may not be reproducedor copied, in whole or in part, without the writtenpermission of the publisher.
Revision History
Revision HistoryDate Revision Contents
2005.10.25 • Portions of “14.2 Diagnostic Trouble Code Datails" revised. (See P1-37, 38, 39, 40, 41)• "15.1 Engine ECU Externa Wring Diagram”illustration (Applicable Illust. code: Q001257E,
Q001258E) replaced. (See P1-42, 43)• Portions of the "15.2 Engine ECU Connector Diagram” Terminal Connections (1), (2), (3) replaced .
(See P1-43, 44, 45)
Table of Contents
Operation Section
1. PRODUCT APPILCATION INFOR-MATION
1.1 Application .................................................. 1-1
1.2 System Components Part Number ............. 1-1
2. OUTLINE OF SYSTEM
2.1 Common Rail System Characteristics ........ 1-2
2.2 Features of Injection Control....................... 1-2
2.3 Comparison to the Conventional System.... 1-3
2.4 Composition ................................................ 1-3
2.5 Operation .................................................... 1-4
2.6 Fuel System................................................ 1-4
2.7 Control System ........................................... 1-4
3. SUPPLY PUMP
3.1 Outline......................................................... 1-6
3.2 Exterior View Diagram ................................ 1-7
3.3 Supply Pump Internal Fuel Flow ................. 1-7
3.4 Construction of Supply Pump ..................... 1-8
3.5 Operation of the Supply Pump.................... 1-9
4. SUPPLY PUMP COMPONENT PARTS
4.1 Feed Pump ................................................1-11
4.2 SCV ( Suction Control Valve )....................1-11
4.3 Fuel Temperature Sensor ......................... 1-13
5. RAIL
5.1 Outline....................................................... 1-14
6. RAIL COMPONENTS PARTS
6.1 Rail Pressure Sensor (Pc Sensor) ............ 1-15
6.2 Pressure limiter ......................................... 1-15
7. INJECTOR (G2 TYPE)
7.1 Outline....................................................... 1-16
7.2 Characteristics .......................................... 1-16
7.3 Exterior View Diagram .............................. 1-17
7.4 Construction.............................................. 1-18
7.5 Operation .................................................. 1-18
7.6 QR Codes ................................................. 1-19
7.7 Injector Actuation Circuit ........................... 1-21
8. OPERATION OF CONTROL SYS-TEM COMPONENTS
8.1 Engine Control System Diagram............... 1-22
8.2 Engine ECU (Electronic Control Unit) ....... 1-22
8.3 Cylinder Recognition Sensor (TDC).......... 1-23
8.4 Turbo Pressure Sensor ............................. 1-23
8.5 Mass Air Flow Sensor ............................... 1-24
8.6 Electronic Control Throttle ........................ 1-25
9. VARIOUS TYPES OF CONTROL
9.1 Outline....................................................... 1-27
9.2 Fuel Injection Rate Control Function......... 1-27
9.3 Fuel Injection Quantity Control Function... 1-27
9.4 Fuel Injection Timing Control Function...... 1-27
9.5 Fuel Injection Pressure Control Function (Rail Pressure Control Function) ............. 1-27
10. FUEL INJECTION QUANTITY CONTROL
10.1 Outline....................................................... 1-28
10.2 Injection Quantity Calculation Method ...... 1-28
10.3 Set Injection Quantities ............................. 1-28
Table of Contents
11. FUEL INJECTION TIMING CON-TROL
11.1 Ouline........................................................ 1-32
11.2 Main and Pilot Injection Timing Control..... 1-32
11.3 Microinjection Quantity Learning Control .. 1-33
12. FUEL INJECTION RATE CON-TROL
12.1 Outline....................................................... 1-35
13. FUEL INJECTION PRESSURE CONTROL
13.1 Fuel Injection Pressure ............................. 1-36
14. DIAGNOSTIC TROUBLE CODES (DTC)
14.1 About the Codes Shown in the Table........ 1-37
14.2 Diagnostic Trouble Code Details............... 1-37
15. EXTERNAL WIRING DIAGRAM
15.1 Engine ECU External Wiring Diagram ...... 1-42
15.2 Engine ECU Connector Diagram.............. 1-43
Operation Section1–1
1. PRODUCT APPILCATION INFORMATION
1.1 Application
1.2 System Components Part Number
Vehicle Manufac-
ture
Vehicle Name Engine Model Specification Destination (Vol-
ume)
Line Off Period
MITSUBISHI TRITON4D56 2WD (MT/AT)
Thailand June, 20054WD (MT)
4M41 4WD (MT/AT)
Parts Name DENSO P/N Manufacturer P/N Remarks
Supply pump SM294000-0331 1460A001 For 4D56 Engine Model
SM294000-0341 1460A003 For 4M41 Engine Model
Injector SM095000-5600 1465A041 For 4D56 Engine Model
SM095000-5760 1465A054 For 4M41 Engine Model
Rail SM095440-0640 1465A034 ALL
Engine ECU MA275800-425# 1860A392 For 4D56 Engine Model (4WD)
MA275800-431# 1860A523 For 4D56 Engine Model (2WD MT)
MA275800-432# 1860A524 For 4D56 Engine Model (2WD AT)
MA275800-357# 1860A390 For 4M41 Engine Model (4WD)
Turbo pressure sensor 079800-5960 MR577031 ALL
Cylinder recognition sensor(TDC)
949979-1590 1865A074 For 4M41 Engine Model
Electronic control throttle 197920-0020 1450A033 For 4M41, 4D56 Engine Model (4WD)
Fuel temperature sensor 179730-0020 MR547077 ALL
Mass air flow meter VN197400-4030 1460A001 ALL
Operation Section1–2
2. OUTLINE OF SYSTEM
2.1 Common Rail System CharacteristicsThe common rail system uses a type of accumulation chamber called a rail to store pressurized fuel, and injectors that contain elec-
tronically controlled solenoid valves to inject the pressurized fuel into the cylinders. Because the engine ECU controls the injection
system (injection pressure, injection rate, and injection timing), the injection system is independent, and thus unaffected by the engine
speed or load. This ensures a stable injection pressure at all times, particularly in the low engine speed range, and dramatically de-
creases the amount of black smoke ordinarily emitted by a diesel engine during start-up and acceleration. As a result, exhaust gas emis-
sions are cleaner and reduced, and higher power output is achieved.
2.2 Features of Injection Control
(1) Injection Pressure Control
• Enables high-pressure injection even at low engine speeds.
• Optimizes control to minimize particulate matter and NOx emissions.
(2) Injection Timing Control
• Enables finely tuned optimized control in accordance with driving conditions.
(3) Injection Rate Control
• Pilot injection control injects a small amount of fuel before the main injection.
Q001223E
Common Rail System
Injection Pressure Control Injection Timing Control Injection Rate Control
Optimization, High Pressurization
Common RailSystem
Conventional Pump
Conventional Pump
Speed SpeedInjection Pressure
Optimization
Common RailSystem
Pa
rtic
ula
te
NO
x
Inje
ctio
n T
imin
g
Speed
Injection Quantity Control
Cylinder Injection Quantity Correction
Pre-Injection
Main Injection
Crankshaft AngleInje
ctio
n R
ate
Inje
ctio
n P
ressu
re
1 3 4 2
Operation Section1–3
2.3 Comparison to the Conventional System
< NOTE >*1 : TWV: Two Way Valve*2 : SCV: Suction Control Valve
2.4 CompositionThe common rail system consists primarily of a supply pump, rail, injectors, and engine ECU.
In-line, VE Pump Common Rail System
System
InjectionQuantityControl
Pump (Governor) Engine ECU, Injector (TWV)*1
InjectionTimingControl
Pump (Timer) Engine ECU, Injector (TWV)*1
RisingPressure
Pump Engine ECU, Supply Pump
Distributor Pump Engine ECU, Rail
InjectionPressureControl
Dependent upon Speed and Injection Quantity Engine ECU, Supply Pump (SCV)*2
Q001224E
High-pressure Pipe
Momentary
High Pressure
NozzleGovernor
Timer
In-line Pump
VE Pump Q001225E
Rail
Usually High Pressure
Supply Pump
Injector
Feed Pump SCV (Suction Control Valve)
Delivery Valve
Fuel Tank
Operation Section1–4
2.5 Operation
(1) Supply Pump (HP3)
• The supply pump draws fuel from the fuel tank, and pumps the high pressure fuel to the rail. The quantity of fuel discharged from the
supply pump controls the pressure in the rail. The SCV (Suction Control Valve) in the supply pump effects this control in accordance
with commands received from the engine ECU.
(2) Rail
• The rail is mounted between the supply pump and the injector, and stores the high-pressure fuel.
(3) Injector (G2 type)
• This injector replaces the conventional injection nozzle, and achieves optimal injection by effecting control in accordance with signals
from the engine ECU. Signals from the engine ECU determine the duration and timing in which current is applied the injector. This
in turn, determines the quantity, rate and timing of the fuel that is injected from the injector.
(4) Engine ECU
• The engine ECU calculates data received from the sensors to comprehensively control the injection quantity, timing and pressure, as
well as the EGR (exhaust gas recirculation).
2.6 Fuel SystemThis system comprises the route through which diesel fuel flows from the fuel tank via the rail to the supply pump, and is injected
through the injector, as well as the route through which the fuel returns to the tank via the overflow pipe.
2.7 Control SystemIn this system, the engine ECU controls the fuel injection system in accordance with signals received from various sensors. The com-
ponents of this system can be broadly divided into the following three types: (1) sensors; (2) ECU; and (3) actuators.
Fuel Temperature
Accelerator OpeningTurbo Pressure,Atmospheric Air Pressure
Intake Airflow Rate
Rail PressureSensor
Rail
Engine ECU
Fuel Temperature Sensor
Supply PumpFuel Tank
Injector
PressureLimiter
SCV(SuctionControl Valve)
Intake Air Temperature
Coolant Temperature
Crankshaft position
Cylinder Recognition Position
Q001226E
Engine Speed
Operation Section1–5
(1) Sensors
• Detect the engine and driving conditions, and convert them into electrical signals.
(2) Engine ECU
• Performs calculations based on the electrical signals received from the sensors, and sends them to the actuators in order to achieve
optimal conditions.
(3) Actuators
• Operate in accordance with electrical signals received from the ECU. Injection system control is undertaken by electronically control-
ling the actuators. The injection quantity and timing are determined by controlling the duration and timing in which current is applied
to the TWV (Two-Way Valve) in the injector. Injection pressure is determined by controlling the SCV (Suction Control Valve) in the
supply pump.
Q001227E
Crankshaft Position Sensor (NE)
Accelerator Position Sensor
Engine Speed
Cylider Recognition Sensor (TDC)
CylinderRecognition
Load
Injector
Supply Pump (SCV)
•Injection Quantity Control•Injection Timing Control
•Fuel Pressure Control
Other Sensors and Switches EGR, Air Intake Control Relay, Light
Sensor Actuator
EngineECU
Operation Section1–6
3. SUPPLY PUMP
3.1 OutlineThe supply pump consists primarily of the pump body (eccentric cam, ring cam, and plungers), SCV (Suction Control Valve), fuel
temperature sensor, and feed pump.
The two plungers are positioned vertically on the outer ring cam for compactness.
The engine drives the supply pump at a ratio of 1:1. The supply pump has a built-in feed pump (trochoid type), and draws the fuel
from the fuel tank, sending it to the plunger chamber.
The internal camshaft drives the two plungers, and they pressurize the fuel sent to the plunger chamber and send it to the rail. The
quantity of fuel supplied to the rail is controlled by the SCV, using signals from the engine ECU. The SCV is a normally open type
(the intake valve opened during de-energization).
Q001265E
InjectorRail
Discharge Valve
Regulating Valve
Feed Pump
Intake
Fuel Inlet
Fuel Overflow
Fuel Tank
Camshaft
Intake pressureFeed pressure
High pressure
Return pressure
Return
Fuel Filter (with Priming Pump)
Filter
Suction Valve
Plunger
Return Spring
SCV
Operation Section1–7
3.2 Exterior View Diagram4D56 Engine Model
4M41 Engine Model
3.3 Supply Pump Internal Fuel FlowThe fuel that is drawn from the fuel tank passes through the route in the supply pump as illustrated, and is fed into the rail.
Q001253E
From Fuel Tank
Overflow to Fuel Tank
To Rail
Fuel Temperature Sensor
SCV
Q001228E
From
Fuel Tank
Overflow to Fuel Tank
To RailFuel
TemperatureSensor
SCV
Operation Section1–8
3.4 Construction of Supply PumpThe eccentric cam is attached to the drive shaft. The eccentric cam is connected to the ring cam.
As the drive shaft rotates, the eccentric cam rotates eccentrically, and the ring cam moves up and down while rotating.
The plunger and the suction valve are attached to the ring cam. The feed pump is connected to the rear of the drive shaft.
Supply pump interior
Regulating valve
Feed pump
Overflow
Fuel tank
SCV (Suction Control Valve)
Intake valve
Discharge valve
Pumping portion (plunger)
Rail
QD0705E
QD0706E
Cam Shaft
Eccentric Cam Ring Cam
Q001233E
Ring Cam
Eccentric Cam
Cam Shaft
Plunger
Operation Section1–9
3.5 Operation of the Supply PumpAs shown in the illustration below, the rotation of the eccentric cam causes the ring cam to push Plunger A upwards. Due to the spring
force, Plunger B is pulled in the opposite direction to Plunger A. As a result, Plunger B draws in fuel, while Plunger A pumps it to the
rail.
Q001234E
Plunger A
Ring Cam
Plunger B
Feed Pump
Operation Section1–10
Q001235E
SCV
Plunger A: Finish Compression
Plunger B: Finish Intake
Plunger A: Finish Intake
Plunger B: Finish Compression
Plunger A: Begin IntakePlunger
B: Begin Compression
Plunger A: Begin Compression
Plunger B: Begin Intake
Suction Valve
Plunger A
Plunger B
Discharge Valve
Eccentric Cam
Ring Cam
Operation Section1–11
4. SUPPLY PUMP COMPONENT PARTS
4.1 Feed PumpThe trochoid type feed pump, which is integrated in the supply pump, draws fuel from the fuel tank and feeds it to the two plungers
via the fuel filter and the SCV (Suction Control Valve). The feed pump is driven by the drive shaft. With the rotation of the inner rotor,
the feed pump draws fuel from its suction port and pumps it out through the discharge port. This is done in accordance with the space
that increases and decreases with the movement of the outer and inner rotors.
4.2 SCV ( Suction Control Valve )A linear solenoid type valve has been adopted. The ECU controls the duty ratio (the duration in which current is applied to the SCV),
in order to control the quantity of fuel that is supplied to the high-pressure plunger.
Because only the quantity of fuel that is required for achieving the target rail pressure is drawn in, the actuating load of the supply
pump decreases.
When current flows to the SCV, variable electromotive force is created in accordance with the duty ratio, moving the cylinder (inte-
grated with the armature) to the left side, and changing the opening of the fuel passage to regulate the fuel quantity.
With the SCV OFF, the return spring contracts, completely opening the fuel passage and supplying fuel to the plungers. (Full quantity
intake and full quantity discharge = normally open)
When the SCV is ON, the force of the return spring moves the cylinder to the left, closing the fuel passage (normally open).
By turning the SCV ON/OFF, fuel is supplied in an amount corresponding to the actuation duty ratio, and fuel is discharged by the
plungers.
QD0708E
Outer Rotor
FromFuel Tank
Intake Port
ToPump Chamber
Discharge
Port
Quantity Decrease
Quantity Increase
Quantity Decrease(Fuel Discharge)
Quantity Increase(Fuel Intake)
Inner Rotor
Q001113E
Valve body
Needle valve
Return Spring
Operation Section1–12
(1) SCV Opening Small (Duty ON time long - Refer to the "Relationship Between ActuationSignal and Current" Diagram.)
• When the opening of the SCV is small, the fuel suction area is kept small, which decreases the transferable fuel volume.
(2) SCV Opening Large (Duty ON time short - Refer to the "Relationship Between ActuationSignal and Current" Diagram.)
• When the opening of the SCV is large, the fuel suction area is kept large, which increases the transferable fuel volume.
Q001114E
Feed Pump
Needle valve Small Opening
Q001115E
Feed Pump
Needle valve Large Opening
Operation Section1–13
(3) Diagram of Relationship Between Actuation Signal and Current (Magneto motive Force)
4.3 Fuel Temperature SensorDetects the fuel temperature and sends a corresponding signal to the engine ECU. Based on this information, the engine ECU calcu-
lates the injection volume correction that is appropriate for the fuel temperature.
Q001116E
Average Current Difference
Small Suction Volume Large Suction Volume
ActuationVoltage
Current
ON
OFF
Q001237E
<Reference: Temperature-resistance Characteristics>
RESISTANCE(°C) (k )TEMPERATURE
- 30 (25.40)
(9.16)
(1.66)
(1.15)
(0.811)
(0.584)
(0.428)
(0.240)
(0.1836)
(0.1108)
(5.74)
(3.70)
15.40 + 1.29- 1.20
+ 0.14- 0.132.45
0.318 ± 0.008
0.1417 ± 0.0018
- 20
- 10
10
20
30
40
50
60
70
80
90
100
110
120
0
Operation Section1–14
5. RAIL
5.1 OutlineStores pressurized fuel (25 to 180 MPa) that has been delivered from the supply pump and distributes the fuel to each cylinder injector.
A rail pressure sensor and a pressure limiter valve are adopted in the rail.
The rail pressure sensor (Pc sensor) detects fuel pressure in the rail and sends a signal to the engine ECU, and the pressure limiter
controls the excess pressure. This ensures optimum combustion and reduces combustion noise.
Q001236E
Pressure SensorPressure Limiter
Operation Section1–15
6. RAIL COMPONENTS PARTS
6.1 Rail Pressure Sensor (Pc Sensor)The pressure sensor detects the fuel pressure of the rail, and sends a signal to the engine ECU. The sensor is made from a semicon-
ductor that uses the Piezo resistive effect to detect changes in electrical resistance based on the pressure applied to the elemental sili-
con. In comparison to the old model, this sensor is compatible with high pressure.
6.2 Pressure limiterThe pressure limiter releases pressure when the internal pressure of the rail becomes abnormally high. The pressure limiter opens when
internal pressure reaches 221MPa (2254 kg/cm2) and closes when rail pressure reaches a given set pressure. Fuel released from the
pressure limiter is returned to the fuel tank.
Q001238E
Vout/Vc
A-VCC A-GNDPEUFL
Vc = 5V
(Mpa)Popt
2001601002000
0.20.264
0.712
0.84
0.52
Q001239E
Valve Open
Valve Close50 MPa (509.5 kg/cm2)
221 MPa (2254 kg/cm2)
From rail
To fuel tank
Operation Section1–16
7. INJECTOR (G2 TYPE)
7.1 OutlineThe injectors inject the high-pressure fuel from the rail into the combustion chambers at the optimum injection timing, rate, and spray
condition, in accordance with commands received from the ECU.
7.2 CharacteristicsA compact, energy-saving solenoid-control type TWV (Two-Way Valve) injector has been adopted.
QR codes displaying various injector characteristics and the ID codes showing these in numeric form (30 alphanumeric figures) are
engraved on the injector head. The common rail system optimizes injection volume control using this information. When an injector
is newly installed in a vehicle, it is necessary to enter the ID codes in the engine ECU using the MITSUBISHI diagnosis tool (MUT
III).
Operation Section1–17
7.3 Exterior View Diagram
Q001244E
<4M41 Engine Model><4D56 Engine Model>
Operation Section1–18
7.4 Construction
7.5 OperationThe TWV (Two-Way Valve) solenoid valve opens and closes the outlet orifice to control both the pressure in the control chamber, and
the start and end of injection.
(1) Non injection
• When no current is supplied to the solenoid, the spring force is stronger than the hydraulic pressure in the control chamber. Thus, the
Q001240E
QR Codes
30 Alphanumeric Figures
Pressurized Fuel (from Rail)
Seat
Leak Passage
Multiple Hole Filter
Pressurized Fuel
Command Piston
Nozzle Spring
Pressure Pin
Nozzle Needle
Control Chamber
Operation Section1–19
solenoid valve is pushed downward, effectively closing the outlet orifice. For this reason, the hydraulic pressure that is applied to the
command piston causes the nozzle spring to compress. This closes the nozzle needle, and as a result, fuel is not injected.
(2) Injection
• When current is initially applied to the solenoid, the attraction force of the solenoid pulls the solenoid valve up, effectively opening
the outlet orifice and allowing fuel to flow out of the control chamber. After the fuel flows out, the pressure in the control chamber
decreases, pulling the command piston up. This causes the nozzle needle to rise and the injection to start.
• The fuel that flows past the outlet orifice flows to the leak pipe and below the command piston. The fuel that flows below the piston
lifts the piston needle upward, which helps improve the nozzle's opening and closing response.
(3) End of Injection
• When current continues to be applied to the solenoid, the nozzle reaches its maximum lift, where the injection rate is also at the max-
imum level. When current to the solenoid is turned OFF, the solenoid valve falls, causing the nozzle needle to close immediately and
the injection to stop.
7.6 QR CodesConventionally the whole injector Assy was replaced during injector replacement, but QR (Quick Response) codes have been adopted
to improve injector quantity precision.
Q001241E
Injection Rate
Control Chamber Pressure
Control Chamber Pressure
Control Chamber Pressure
Solenoid
TWV
Outlet Orifice
Inlet Orifice
Command Piston
NozzleInjection Rate Injection Rate
Non-Injection Injection End of Injection
Rail
Actuating Current
Actuating Current
Actuating Current
To Fuel TankLeak Passage
TWV
Operation Section1–20
4D56 Engine Model
4M41 Engine Model
QR codes have resulted in a substantial increase in the number of fuel injection quantity correction points, greatly improving precision.
The characteristics of the engine cylinders have been further unified, contributing to improvements in combustion efficiency, reduc-
tions in exhaust gas emissions and so on.
(1) Repair Procedure
• When replacing injectors with QR codes, or the engine ECU, it is necessary to record the ID codes in the ECU. (If the ID codes for
the installed injectors are not registered correctly, engine failure such as rough idling and noise will result). The ID codes will be reg-
istered in the ECU at a MITSUBISHI dealer using approved MITSUBISHI tools.
Q001243E
ID Codes (30 base 16 characters)Base 16 characters noting fuel injection quantity correction information for market service use
QR Codes ( 9.9mm)
Q001242E
ID Codes (30 base 16 characters)Base 16 characters noting fuel injection quantity correction information for market service use
QR Codes ( 9.9mm)
Q001245E
Inje
ctio
n Q
ua
ntity
Q
180 Mpa
80 Mpa
112 Mpa
135 Mpa
48 Mpa
25 Mpa
Actuating Pluse Width TQ
Inje
ctio
n Q
ua
ntity
Q
180 Mpa
64 Mpa
96 Mpa130 Mpa
48 Mpa
25 Mpa
Actuating Pluse Width TQ
<4D56 Engine Model> <4M41 Engine Model>
Correction
8 Points
Correction
8 Points
Operation Section1–21
Replacing the Injector
Replacing the Engine ECU
7.7 Injector Actuation CircuitIn order to improve injector responsiveness, the actuation voltage has been changed to high voltage, speeding up both solenoid mag-
netization and the response of the TWV. The EDU or the charge circuit in the ECU raises the respective battery voltage to approxi-
mately 85V, which is supplied to the injector by signal from the ECU to actuate the injector.
Q001133E
"No correction resistance, cannot be detected electrically"
Replaced injector
Engine ECU
* Injector ID code must be registered with the engine ECU
Q001134E
"No correction resistance, cannot be detected electrically"
* Injector ID code must be registered with the engine ECU
Vehicle injectors
Replaced engine ECU
Q001246E
Constant Amperage Circuit
High Voltage Generation Circuit
ECU
Actuating Current
<ECU Direct Actuation>
2WV#3 (No.4 Cylinder)
2WV#4 (No.2 Cylinder)
Injector
Common 1
2WV#1 (No.1 Cylinder)
2WV#2 (No.3 Cylinder)
Operation Section1–22
8. OPERATION OF CONTROL SYSTEM COMPONENTS
8.1 Engine Control System Diagram
8.2 Engine ECU (Electronic Control Unit)This is the command center that controls the fuel injection system and the engine operation in general.
Q001247E
Rail
Rail Pressure Sensor
(Pc Sensor) Pressure limiter
injector
Engine ECU
SCV
(Sucton Control Valve)
Glow Relay
Crankshaft Position Sensor
(NE Sensor)
Cylinder Recognition
Position Sensor
(TDC Sensor)
Turbo PressureSensor
Electronic ControlThrottle
Fuel Tank
Accelerator Position Sensor
Ignition Switch Signal
Starter Signal
Vihicle Speed Signal
Mitsubishi Diagnosis Tool (MUDIII)
Battery Voltage
Other Signals
Air Mass Flow Sensor
(With Intake Air Temperature)
Fuel Temperature
Sensor
Coolant
Temperature
Sensor
Operation Section1–23
8.3 Cylinder Recognition Sensor (TDC)Outputs a cylinder identification signal. The sensor outputs 5 pulses for every two revolutions (720°CA) of the engine.
8.4 Turbo Pressure SensorThis is a type of semi-conductor pressure sensor. It utilizes the characteristics of the electrical resistance changes that occur when the
pressure applied to a silicon crystal changes. Because a single sensor is used to measure both turbo pressure and atmospheric pressure,
a VSV is used to alternate between atmospheric and turbo pressure measurement.
Q001248E
<Outline Diagram>
Engine ECU
Detection Calculation Actuation
Sensor Actuator
Q001249E
30°CA 180°CA 180°CA
720°CA
180°CA
5V
1V
0V
Pulser
SensorSignal
Vcc
GND
OUT
Q001229E
GND PBVC
Operation Section1–24
(1) Atmospheric Pressure Measurement Conditions
• The VSV turns ON for 150msec to detect the atmospheric pressure when one of the conditions below is present:
• Engine speed = 0rpm
• Starter is ON
• Idle is stable
(2) Turbo Pressure Measurement Conditions
• The VSV turns OFF to detect the turbo pressure if the atmospheric pressure measurement conditions are absent.
8.5 Mass Air Flow SensorThis air flow meter, which is a plug-in type, allows a portion of the intake air to flow through the detection area. By directly measuring
the mass and the flow rate of the intake air, the detection precision has been improved and the intake air resistance has been reduced.
This mass air flow meter has a built-in intake air temperature sensor.
Q001231E
VSV Atmosphere
Turbo Pressure Sensor
Intake Manifold
0.5
4.5
3.2
VC = 5 V
266.6
Absolute Pressure
66.6 202.7
500 20001520
PB (V)
kPa (abs)
mmHg (abs)
<Pressure Characteristics>
ECU
Turbo Pressure Sensor
Pressure Sensor Device
Engine ECU
Constant VoltagePower Supply
Microcomputer
Input SignalProcessing Circuit
Vc
PB
GND
Operation Section1–25
8.6 Electronic Control Throttle
(1) Outline
• The suctioning of air is stopped through interlocking the intake throttle with the key switch in order to reduce engine vibration when
the vehicle is turned off.
Q001260E
Engine ECUEFI Main Relay
Airflow MeterPower Supply
VG
+B
EVG
IC
THAE2Intake Air
Voltage Detection
Voltage Detection
Power Supply
Intake Air Temperature Sensor
Heating Element
Air Thermometer
5V
Temperaturesensingelement
E2 THA VG E2 G +B
Heatingelement
Temperaturesensor
Air
Air Flow-VG Characteristic
5
4
3
2
1
0
VG
(V)
1 2 5 10 20 50 100 200
Air Flow (x10-3kg/s)
-200.2
0.3
0.50.7
1
2
3
57
10
20
30
kΩ
20 40 60 80 °C0
Operation Section1–26
(2) Operation
Q001256E
VTA1
VTA1 M+ M-
IC1
VC
VC
VTA2
VTA2
E2
E2
M+
M-
IC2
M
Valve Fully Opened
(Mechanical)
Valve Fully Opened
(by Control)
Valve Fully Closed
Q001232E
ON
Target Valve Opening
(Percentage)
Throttle valve fully opened
(by control)
Key switch OFF throttle valve shut.
Approx. 0.1 - 0.2 sec.
Engine OFF, valve fully opened
(by control) Valve fully opened
(mechanical)
OFF
100%
Engine Key
0%
Operation Section1–27
9. VARIOUS TYPES OF CONTROL
9.1 OutlineThis system effects fuel injection quantity and injection timing control more appropriately than the mechanical governor and timer
used in the conventional injection pump. The engine ECU performs the necessary calculations in accordance with the sensors installed
on the engine and the vehicle. It then controls the timing and duration of time in which current is applied to the injectors, in order to
realize both optimal injection and injection timing.
9.2 Fuel Injection Rate Control FunctionPilot injection control injects a small amount of fuel before the main injection.
9.3 Fuel Injection Quantity Control FunctionThe fuel injection quantity control function replaces the conventional governor function. It controls the fuel injection to an optimal
injection quantity based on the engine speed and accelerator position signals.
9.4 Fuel Injection Timing Control FunctionThe fuel injection timing control function replaces the conventional timer function. It controls the injection to an optimal timing based
on the engine speed and the injection quantity.
9.5 Fuel Injection Pressure Control Function (Rail Pressure Control Func-tion)
The fuel injection pressure control function (rail pressure control function) controls the discharge volume of the pump by measuring
the fuel pressure at the rail pressure sensor and feeding it back to the ECU. It effects pressure feedback control so that the discharge
volume matches the optimal (command) value set in accordance with the engine speed and the injection quantity.
Operation Section1–28
10. FUEL INJECTION QUANTITY CONTROL
10.1 OutlineThis control determines the fuel injection quantity by adding coolant temperature, fuel temperature, intake air temperature, and intake
air pressure corrections to the basic injection quantity. The engine ECU calculates the basic injection quantity based on the engine
operating conditions and driving conditions.
10.2 Injection Quantity Calculation MethodThe calculation consists of a comparison of the following two values: 1. The basic injection quantity that is obtained from the governor
pattern, which is calculated from the accelerator position and the engine speed. 2. The injection quantity obtained by adding various
types of corrections to the maximum injection quantity obtained from the engine speed. The lesser of the two injection quantities is
used as the basis for the final injection quantity.
10.3 Set Injection Quantities
(1) Basic Injection Quantity
• This quantity is determined by the engine speed and the accelerator opening. With the engine speed constant, if the accelerator opening
increases, the injection quantity increases; with the accelerator opening constant, if the engine speed rises, the injection quantity de-
creases.
Q001152E
Engine Speed
Engine Speed
Accelerator Opening
Inje
ctio
n
Qu
an
tity
Inje
ctio
n
Qu
an
tity
Accelerator Opening
Engine Speed
Basic Injection Quantity
Maximum Injection Quantity
Low Quantity
Side Selected
Corrected Final Injection
Quantity
Injector Actuation
Period Calculation
Individual Cylinder Correction Quantity
Turbo Pressure Correction
Atmospheric Pressure Correction
Intake Air Temperature Correction
Speed Correction
Injection Pressure Correction
Operation Section1–29
(2) Maximum Injection Quantity
• This is determined based on the basic maximum injection quantity determined by the engine speed, and the added corrections for in-
take air pressure.
(3) Starting Injection Quantity
• When the starter switch is turned ON, the injection quantity is calculated in accordance with the starting base injection volume. The
base injection quantity and the inclination of the quantity increase/decrease change in accordance with the water temperature and the
engine speed.
(4) Idle Speed Control (ISC) System
• This system controls the idle speed by regulating the injection quantity in order to match the actual speed to the target speed calculated
by the engine ECU.
Ba
sic
In
jectio
n Q
ua
ntity
Engine Speed
Accelerator Opening
Q000888E
QB0717E
Engine Speed
Ba
sic
Ma
xim
um
In
jectio
n Q
ua
ntity
Base injectionquantity
Starter ON time
Start
Water temperature
STA/ONQD0805
Inje
ctio
n qu
antit
y
Operation Section1–30
• The target speed varies, depending on the ON/OFF state of the air conditioner and the coolant temperature.
(5) Idle Vibration Reduction Control
• In order to reduce vibration during idling, the angular (time difference between A and B [C and D]) speed of each cylinder is detected
using the speed pulse signal to control the injection quantity of each cylinder. As a result crank angle speed becomes more uniform
and smoother engine operation is achieved.
Q001254E
•Coolant Temperature
•Air Conditioner Load
•Gear Position
Accelerator Opening
Vehicle Speed
Conditions for Start of Control Control Conditions
Target Speed Calculation
Comparison
InjectionQuantityCorrection
SpeedDetection
Air Conditioner S/W
Coolant Temperature
Neutral S/W Ta
rge
t S
pe
ed
C
alc
ula
tio
n
Inje
ctio
nQ
ua
ntity
De
term
ina
tio
n
[Target speed]
800
20
Coolant water temperature (°C)QD1172
En
gin
e s
pe
ed
(rp
m)
A/C ON/OFF
Operation Section1–31
Speed Pulse
Control Diagram
Q001255E
30°CA360°CA
5V
0V
Pulser
Sensor Signal
(Make the t for all the cylinders equal.)
( t1,4_L)A
( t1,4_H)B
( t2,3_L)C
( t2,3_H)D
Cylinder #1(#4) Cylinder #2(#3)
Q001230E
Crankshaft Angle Crankshaft AngleCorrection
#1 #1 #3 #4 #2#3 #4 #2CrankAngleSpeed
Operation Section1–32
11. FUEL INJECTION TIMING CONTROL
11.1 OulineFuel injection timing is controlled by varying the timing in which current is applied to the injectors.
11.2 Main and Pilot Injection Timing Control
(1) Main Injection Timing
• The engine ECU calculates the basic injection timing based on the engine speed and the final injection quantity, and adds various types
of corrections in order to determine the optimal main injection timing.
(2) Pilot Injection Timing (Pilot Interval)
• Pilot injection timing is controlled by adding a pilot interval to the main injection timing. The pilot interval is calculated based on the
final injection quantity, engine speed, coolant temperature, ambient temperature, and atmospheric pressure (map correction). The pilot
interval at the time the engine is started is calculated from the coolant temperature and engine speed.
Top Dead Center (TDC)
Pilot Injection
Main Injection
Interval
QB0723E
Operation Section1–33
(3) Injection Timing Calculation Method
11.3 Microinjection Quantity Learning Control
(1) Outline
• Quantity learning control is used in every vehicle engine (injector) to preserve the accuracy of quantity (specifically, pilot injection
quantity.)
This type of control is first performed when shipped from the factory (L/O), and later is automatically performed every time the vehicle
runs a set distance (for details, see item "A".) Because of quantity learning control, the accuracy of each injector can be preserved not
only initially, but also as deterioration in injection occurs over time. As a result of this learning, correction values are recorded in the
ECU. During normal driving operations, this correction value is used to make modifications to injection commands, resulting in ac-
curate microinjection.
(2) Learning Operations
• For every two no load, idle instability conditions established (See chart "A" below) quantity learning takes place.
In addition, it is also possible to perform quantity learning control manually as a diagnostic tool.
NE Pulse
Solenoid Valve Control Pulse
Nozzle Needle Lift
0 1Actual TDC
Main InjectionPilot Injection
Pilot Injection Timing Main Injection TimingPilot Interval
Basic InjectionTiming
Corrections
Engine Speed
Injection Quantity
Main InjectionTiming
Atm
osph
eric
Pres
sure
Cor
rect
ion
Cool
ant T
empe
ratu
re C
orre
ctio
n
Inta
ke A
ir Te
mpe
ratu
re C
orre
ctio
n
Inta
ke A
ir Pr
essu
re C
orre
ctio
n
[1] Outline of Timing Control
[2] Injection Timing Calculation Method
QB0724E
Vo
lta
ge
Co
rre
ctio
n
Operation Section1–34
(3) Operational Outline
• Learning control sends ISC (target speed correction quantity) and FCCB (cylinder-to-cylinder correction quantity) feedback based on
engine speed to apply injection control. The correction quantity is added to each cylinder based on ISC and FCCB correction infor-
mation. The corrected injection quantity is then calculated.
Through the use of quantity learning control, injection is divided into 5 injections. In this state, the value for ISC and FCCB corrected
injection quantity that has been divided into five injections is calculated as the "learning value".
Q001250E
Manual Learning Operations (as a Diagnostic Tool)
(A)
Number of IG OFF Occurrences
Vehicle Running Distance
Injection Quantity Deterioration Over Time Judgment
No Load Idle Instability Condition
Establishment of
Learning Operations
Q001251E
1st Cylinder
2nd Cylinder
3th Cylinder
4th Cylinder
1st Cylinder
2nd Cylinder
3th Cylinder
4th Cylinder
: ISC Correction Portion
ISC
Correction
Portion
: FCCB Correction Portion
FCCB
Correction
Portion
<Calculated Microinjection Quantity>
<When Performing Microinjection Quantity Learning>
Learning
Value
Operation Section1–35
12. FUEL INJECTION RATE CONTROL
12.1 OutlineWhile the injection rate increases with the adoption of high-pressure fuel injection, the ignition lag, which is the delay from the time
fuel is injected to the beginning of combustion, cannot be shortened to less than a certain value. As a result, the quantity of fuel that
is injected until main ignition occurs increases, resulting in an explosive combustion at the time of main ignition. This increases both
NOx and noise. For this reason, pilot injection is provided to minimize the initial ignition rate, prevent the explosive first-stage com-
bustion, and reduce noise and NOx.
Normal Injection Pilot Injection
Large First-stage Combustion (NOx and Noise)
Small First-stage Combustion
Injection Rate
Heat Release Rate
-20 TDC 20 40
Crankshaft Angle (deg)
-20 TDC 20 40
Crankshaft Angle (deg)QD2362E
Operation Section1–36
13. FUEL INJECTION PRESSURE CONTROL
13.1 Fuel Injection PressureThe engine ECU determines the fuel injection pressure based on the final injection quantity and the engine speed. The fuel injection
pressure at the time the engine is started is calculated from the coolant temperature and engine speed.
Q000632E
Pressure
Pump Speed
Final Injection Quantity
Operation Section1–37
14. DIAGNOSTIC TROUBLE CODES (DTC)
14.1 About the Codes Shown in the TableThe "SAE" diagnostic trouble code indicates the code that is output through the use of the STT (WDS). (SAE: Society of Automotive
Engineers)
14.2 Diagnostic Trouble Code DetailsThe DTC chart below is common to the 4D56/4M41 model. However, DTC number "P1210" is only for use with the 4D56 2WD mod-
el engine.
DTC
Number
(SAE)
Diagnostic Item Diagnostic Classifica-
tion
Malfunctioning Part Light
ON
Remarks
P0016 Speed-G phase gapmalfunction
Pulse system malfunc-tion
Crankshaft position sen-sor, cylinder recognitionsensor
Yes
P0072 Intake manifold tem-perature sensor - low
Open circuit detection(+B short, ground short,open)
Intake temperature sensor No
P0073 Intake manifold tem-perature sensor - high
Open circuit detection(+B short, ground short,open)
Intake temperature sensor No
P0088 Rail high pressureabnormality
Fuel pressure controlsystem abnormality
Injector Yes
P0089 SCV stuck diagnosis Fuel pressure controlsystem abnormality
Supply pump Yes
P0093 Fuel leak Fuel leak Fuel piping Yes
P0102 Airflow sensor - low Open circuit detection(+B short, ground short,open)
Airflow sensor No
P0103 Airflow sensor - high Open circuit detection(+B short, ground short,open)
Airflow sensor No
P0106 Turbo pressure sensorcharacteristic abnor-mality
Sensor characteristicabnormality
Turbo pressure sensor Yes
P0107 Turbo pressure sensor- low
Open circuit detection(+B short, ground short,open)
Turbo pressure sensor Yes
P0108 Turbo pressure sensor- high
Open circuit detection(+B short, ground short,open)
Turbo pressure sensor Yes
Operation Section1–38
P0112 Intake temperaturesensor - low
Open circuit detection(+B short, ground short,open)
Intake temperature sen-sor (AFS)
Yes
P0113 Intake temperaturesensor - high
Open circuit detection(+B short, ground short,open)
Intake temperature sen-sor (AFS)
Yes
P0117 Coolant temperaturesensor - low
Open circuit detection(+B short, ground short,open)
Coolant temperaturesensor
Yes
P0118 Coolant temperaturesensor - high
Open circuit detection(+B short, ground short,open)
Coolant temperaturesensor
Yes
P0122 Electronic controlthrottle - low
Open circuit detection(+B short, ground short,open)
Electronic control throttle Yes
P0123 Intake valve sensor -high
Open circuit detection(+B short, ground short,open)
Electronic control throttle Yes
P0182 Fuel temperature sen-sor - low
Open circuit detection(+B short, ground short,open)
Supply pump Yes
P0183 Fuel temperature sen-sor - high
Open circuit detection(+B short, ground short,open)
Supply pump Yes
P0191 Rail pressure sensorcharacteristic abnor-mality
Sensor characteristicabnormality
Rail Yes
P0192 Rail pressure sensor(time) low
Open circuit detection(+B short, ground short,open)
Rail Yes
P0193 Rail pressure sensor(time) high
Open circuit detection(+B short, ground short,open)
Rail Yes
P0201 TWV 1 (No.1 cylin-der) actuation systemopen circuit
Injector actuationabnormality
Injector Yes
P0202 TWV 4 (No.2 cylin-der) actuation systemopen circui
Injector actuationabnormality
Injector Yes
P0203 TWV 2 (No.3 cylin-der) actuation systemopen circuit
Injector actuationabnormality
Injector Yes
P0204 TWV 3 (No.4 cylin-der) actuation systemopen circuit
Injector actuationabnormality
Injector Yes
DTC
Number
(SAE)
Diagnostic Item Diagnostic Classifica-
tion
Malfunctioning Part Light
ON
Remarks
Operation Section1–39
P0219 Engine overrunabnormality
Engine abnormality Engine Yes
P0234 High boost abnormal-ity diagnosis
Engine abnormality Engine Yes
P0335 No speed pulse input Pulse system malfunc-tion
Crankshaft position sen-sor
Yes
P0336 Abnormal speedpulse number
Pulse system malfunctio Crankshaft position sen-sor
Yes
P0340 No G pulse input Pulse system malfunc-tion
Cylinder recognition sen-sor
Yes
P0341 Cylinder recognitionsensor pulse numberabnormality
Pulse system malfunc-tion
Cylinder recognition sen-sor
Yes
P0405 EGR lift sensor - low Open circuit detection(+B short, ground short,open)
EGR valve No
P0406 EGR lift sensor - high Open circuit detection(+B short, ground short,open)
EGR valve No
P0502 Vehicle speedabnormality - low
Pulse system malfunc-tion
Vehicle speed sensor Yes
P0604 RAM abnormality Engine ECU Engine ECU Yes
P0605 Engine ECU flash-ROM abnormality
Engine ECU Engine ECU Yes
P0606 Engine ECU CPUabnormality (main ICabnormality)
Engine ECU Engine ECU Yes
P0607 Engine ECU abnor-mality (monitoring ICabnormality)
Engine ECU Engine ECU Yes
P0628 SCV actuation sys-tem abnormality
Fuel pressure controlsystem abnormality
Supply pump Yes
P0629 SCV +B short Fuel pressure controlsystem abnormality
Supply pump Yes
P0638 Intake throttle valvestuck
Actuator malfunction Electronic control throttle Yes
P0642 Sensor - voltage 1low
Engine ECU Engine ECU Yes
P0643 Sensor - voltage 1high
Engine ECU Engine ECU Yes
P0652 Sensor - voltage 2low
Engine ECU Engine ECU Yes
P0653 Sensor - voltage 2high
Engine ECU Engine ECU Yes
DTC
Number
(SAE)
Diagnostic Item Diagnostic Classifica-
tion
Malfunctioning Part Light
ON
Remarks
Operation Section1–40
P1203 Low charge Engine ECU Engine ECU Yes
P1204 Over charge Engine ECU Engine ECU Yes
P1210 Throttle valveopening malfunction
Actuator malfunction Throttle valve Yes Only 4D56 Engine2WD
P1272 P/L open valveabnormality
Fuel pressure controlsystem abnormality
Rail Yes
P1273 Single pump abnor-mality diagnosis
Fuel pressure controlsystem abnormality
Supply pump Yes In the event that thevehicle runs out of gas,"P1273" may bedetected when thevehicle is restarted.When "P1273" is dis-played, the user shouldverify whether or notthere is gas in the vehi-cle.Do not replace thepump assy. if it hasbeen verified that thevehicle has run out ofgas. Remove the airfrom the fuel, and erasethe code using theMITSUBISHI MUT IIIdiagnosis tool.
P1274 Pump protective fillplug
Fuel pressure control system abnormality
Supply pump Yes
P1275 Pump exchange fillplug
Fuel pressure control system abnormality
Supply pump Yes
P1625 QR dataabnormality
Engine ECU Engine ECU Yes
P1626 QR data failure towrite to disc malfunc-tion
Engine ECU Engine ECU Yes
P2118 DC motor over cur-rent abnormality
Actuator malfunction Electronic control throttle Yes
P2122 Accelerator sensor-1low
Open circuit detection(+B short, ground short,open)
Accelerator position sen-sor
Yes
P2123 Accelerator sensor-1high final
Open circuit detection(+B short, ground short,open)
Accelerator position sen-sor
Yes
P2124 Accelerator sensor-1high
Open circuit detection(+B short, ground short,open)
Accelerator position sen-sor
No
DTC
Number
(SAE)
Diagnostic Item Diagnostic Classifica-
tion
Malfunctioning Part Light
ON
Remarks
Operation Section1–41
P2127 Accelerator sensor-2low
Open circuit detection(+B short, ground short,open)
Accelerator position sen-sor
Yes
P2138 Accelerator sensor -duplicate malfunc-tion high
Open circuit detection(+B short, ground short,open)
Accelerator position sen-sor
Yes
P2138 Accelerator sensor -duplicate malfunc-tion low
Open circuit detection(+B short, ground short,open)
Accelerator Position Sen-sor
Yes
ACCP characteristicabnormality
Sensor characteristicabnormality
Accelerator Position Sen-sor
Yes
P2146 Common 1 systemopen circuit
Injector actuationabnormality
Injector, Wire harness orEngine ECU
Yes
P2147 COM1 TWV actua-tion system groundshort
Injector actuationabnormality
Injector, Wire harness orEngine ECU
Yes
P2148 COM1 TWV actua-tion system +B short
Injector actuationabnormality
Injector, Wire harness orEngine ECU
Yes
P2149 Common 2 systemopen circuit
Injector actuationabnormality
Injector, Wire harness orEngine ECU
Yes
P2228 Atmospheric pres-sure sensor - low
Open circuit detection(+B short, ground short,open)
Engine ECU Yes
P2229 Atmospheric pres-sure sensor - high
Open circuit detection(+B short, ground short,open)
Engine ECU Yes
P2413 EGR feedback abnor-mality
Actuator malfunction EGR valve No
UD073 CAN bus OFF error Network Network No
UD101 CAN time out flag(trans)
Network Network No
UD109 CAN time out flag(ETACS)
Network Network No
UD190 CAN communication Network Network No
DTC
Number
(SAE)
Diagnostic Item Diagnostic Classifica-
tion
Malfunctioning Part Light
ON
Remarks
Operation Section1–42
15. EXTERNAL WIRING DIAGRAM
15.1 Engine ECU External Wiring DiagramThe wiring diagram below is common to the 4D56/4M41 model.
Q001257E
ThrottleSolenoid Valve
SCV(SuctionControl Valve)
AirConditioningRelay
FAN Relay
Control (ECCS) Relay
P1 P2
BATT
Air Conditioning 2 Switch
Air Conditioning 1 Switch
Glow Light
Glow Pulg RelayBATT
Key ACCI
SOFF
Battery
Starter
MotorEGR
Position
Sensor
EGR
DC Motor
Elecronic
Throttle
Control
Body
Earth
P1
Engine Warning Light
Tacho Meter
Vehicle Speed Sensor
NE+
NE-
A46
A65
A-VCC3
A-VCC4
Crankshaft
Position
Sensor
Cylinder
Recognition
Sensor
A44
A45
BATTB40
A/C2 SWA31
A/C1 SW A12
WA16
GROW LA38
GROW RA37
IG-SWB26
STA-SWB18
EGR LIFT RTNA72
EGR LIFTA53
B05
EGR -A07
EGR +A08
ETC -B37
ETC +B35
ETCP-S
ETCP-M
A81
SPDB16
TACHOB25
+BPB38
+BPB39
M-RELB24
THRA15
C FAN RA27
A/C RA26
CAN1-H
CAN1-L
B14
B06
SCVA17
G+
G-
A47
A66
PS-SW Power Steering Switch
Reverse Shift Switch
1st Shift Switch
Air Temperature Sensor
Fuel Temperature Sensor
Body
Earth
BATT
AcceleratorPosition Sensor
B30
MT REV SW B20
MT 1ST SW B19
A-VCC1 B01
APS1 B02
APS1 GND B03
A-VCC2 B09
APS2 B10
APS2 GND B11
A10
SCV-
SCV(Suction Control Valve)
SCV+
A29
A79
THF
THA
A50
THFRTN A69
Coolant Temperature SensorA51
THWRTN
THW
A70
Operation Section1–43
15.2 Engine ECU Connector DiagramThe connector diagram and terminal below are common to the 4D56/4M41 model.
Terminal Connections (1)
No. Pin Symbol Signal Name No. Pin Symbol Signal Name
A01 P-GND Power Ground A11 — —
A02 — — A12 A/C1 SW Air Conditioning 1 Switch
A03 P-GND Power Ground A13 — —
A04 COMMON 1 INJ#1/#4 BATT. A14 — —
A05 COMMON 1 INJ#2/#3 BATT. A15 THR Throttle Solenoid Valve
A06 — — A16 W EngineWarning Light
A07 EGR- EGR-DC Motor (-) A17 SCV SCV (Suction Control Valve)
A08 EGR+ EGR-DC Motor (+) A18 — —
A09 — — A19 — —
A10 SCV+ SCV (Suction Control Valve) A20 — —
Q001258E
Rail Pressure Sensor
(Pc Sensor)
EXTAir Temperature Sensor
Airflow Sensor
P1
Turbo Pressure Sensor
COMMON1A04
TWV1A43
TWV1A42
COMMON1A05
TWV2
TWV2
A24
Injector3 Drive (#4 Cylinder)
A23
TWV3A41
TWV3A40
TWV4A22
TWV4A21
P-GND
Body Earth
P-GND
C-GND
A01
A03
B33
A48PFUEL1
A49
A63
PFUEL2
A-VCC5
A68PFUEL RTN
A64
A52BOOST
A71BOOST RTN
A-VCC6
A55
A74
A54AMF
A73AMF RTN
EXT-A-TMP
EXT-A-RTNInjector4 Drive (#2 Cylinder)
Injector2 Drive (#3 Cylinder)
Injector1 Drive (#1 Cylinder)
Q001259E
Operation Section1–44
Terminal Connections (2)
No. Pin Symbol Signal Name No. Pin Symbol Signal Name
A21 TWV4 Injection 4 Drive (#2 Cylinder) A57 — —
A22 TWV4 Injection 4 Drive (#2 Cylinder) A58 — —
A23 TWV2 Injection 2 Drive (#3 Cylinder) A59 — —
A24 TWV2 Injection 2 Drive (#3 Cylinder) A60 — —
A25 — — A61 — —
A26 A/C R Air Conditioning Relay A62 — —
A27 C FAN R FAN Relay A63 A-VCC5 Rail Pressure Sensor (PC Sensor)Source
A28 — — A64 A-VCC6 Turbo Pressure Sensor Source (5V)
A29 SCV- SCV (Suction Control Valve) A65 NE- Crankshaft Position Sensor Ground
A30 TEST Test Switch Input A66 G- Cylinder Recognition Sensor Ground
A31 A/C2 SW Air Conditioning 2 Switch A67 — —
A32 — — A68 PFUEL RTN Rail Pressure Sensor Earth
A33 — — A69 THF RTN Air Temperature Sensor, Fuel Temper-ature Sensor Earth
A34 — — A70 THW RTN Coolant Temperature Sensor Earth
A35 — — A71 BOOST RTN Turbo Pressure Sensor
A36 — — A72 EGR LIFTRTS
EGR Position Sensor Earth
A37 GLOW R Glow Plug Relay A73 AMF-RTN Airflow Sensor Earth
A38 GLOW L Glow Light A74 EXT-A-RTN Air Temperature Sensor Earth (W/FAS)
A39 — — A75 — —
A40 TWV3 Injection 3 Drive (#4 Cylinder) A76 — —
A41 TWV3 Injection 3 Drive (#4 Cylinder) A77 — —
A42 TWV1 Injection 1 Drive (#1 Cylinder) A78 — —
A43 TWV1 Injection 1 Drive (#1 Cylinder) A79 THA Air Temperature Sensor
A44 A-VCC3 Crankshaft Position Sensor BATT A80 — —
A45 A-VCC4 Cylinder Recognition Sensor BATT A81 ETCP-S Electoronic Throttle Control (Sub)
A46 NE+ Crankshaft Position Sensor B01 A-VCC 1 Accelerator Position Sensor (Main)Source
A47 G+ Cylinder Recognition Sensor B02 APS 1 Accelerator Position Sensor (Main)
A48 PFUEL Rail Pressure Sensor (PC Sensor) B03 APS 1 GND Accelerator Position Sensor (Main)Earth
A49 PFUEL Rail Pressure Sensor (B/UP) B04 — —
A50 THF Fuel Temperature Sensor B05 ETCP-M Electoronic Throttle Control (Main)
A51 THW Coolant Temperature Sensor B06 CAN1-L CAN L (W/Resister)
A52 BOOST Turbo Pressure Sensor B07 — —
A53 EGR LIFT EGR Position Sensor B08 — —
A54 AMF Airflow Sensor B09 A-VCC 2 Accelerator Position Sensor (Sub)Source
A55 EXT-A-TMP Air Temperature Sensor (W/AFS) B10 APS 2 Accelerator Position Sensor (Sub)
Operation Section1–45
Terminal Connections (3)
No. Pin Symbol Signal Name No. Pin Symbol Signal Name
B11 APS 2 GND Accelerator Position Sensor (Sub)Earth
B26 IG-SW Ignition Switch
B12 — — B27 — —
B13 — — B28 — —
B14 CAN1-H CAN H (W/Resister) B29 — —
B15 — — B30 PS-SW Power Steering Switch
B16 SPD Vehicle Speed Sensor B31 — —
B17 — — B32 — —
B18 STA-SW Starter Switch B33 C-GND Signal Ground
B19 MT 1ST SW 1st Shift Switch B34 — —
B20 MT REV SW Reverse Shift Switch B35 ETC+ Electronic Throttle Control Motor (+)
B21 — — B36 — —
B22 — — B37 ETC- Electronic Throttle Control Motor (-)
B23 — — B38 +BP Battery
B24 M-REL Control (ECCS) Relay (W/DIODE)
B39 +BP Battery
B25 TACHO Tacho Meter B40 BATT Battery (Back-up, W/Monitor)
Operation Section1–46
DENSO INTERNATIONAL THAILAND Field Technical Service Department
Edited and published by:
369 Moo 3 Teparak Rd. Muang Samutprakarn Thailand
Published : June 2005
Printed in Thailand