commercial grade reel system for inground solar pool ... · for inground solar pool covers...
TRANSCRIPT
Commercial Grade Reel SystemFor Inground Solar Pool Covers
Installation Instructions
5. Lock the tubes together by rotating each adjoining tube in the opposite direction, ensuring all small tubes are rotated clockwise. Refer Diagram 5.6. Secure each tube with just one self-drilling screw in each join.7. Slide the tube assembly into the hand wheel and tubing plug inserts by pushing the tube until it meets the wheel surface at each end and check for fit. If it doesn’t fit, undo just one screw in one join and adjust.8. When the tube length is correct, drill and fasten the remaining screws at each end of the overlapped tubes. You should have six (6) screws on each tube end where there is a join. For covers over 40 m2 use twelve (12) screws per join overlap.9. Put the tube assembly together with hand wheel and tube plug inserts by using three (3) self-drilling screws per wheel end. Make sure Aluminium tube is pushed hard against hand wheel before inserting first screw. Refer Diagram 6.10. Attach cords to tubes. Measure along the tube, 150 mm in from each edge of the pool toward the middle. There are enough fasteners for up to twelve (12) cords to attach the blanket. These need only be placed 1000 mm apart but we have provided plenty of cord so you can use twelve (12) and they can be cut to a suitable length, up to 1750 mm. You need to allow at least 400 mm more cord length than the distance between the blanket and the tube. Mark the tube with cord positions evenly spaced. Fasten a self-drilling screw through a domed washer at each mark on the flat of the tube to within 3 mm of being tight. This is enough room to now slide the cord under the washer in a loop and hold both pieces of cord, then screw until tight. Refer Diagram 7.11. Attach the cord to the blanket. The cords are fastened to the blanket using the plastic grommets. For rectangular pools where the reel is positioned at one end of the pool, a single grommet is fastened 50 mm in from the edge of the blanket, aligned with each cord from the tube. Refer Diagram 8. On irregular shaped pools where the tube spans the pool, you will need two grommets per cord spaced 50 mm apart. Refer Diagram 9. Using a hammer and a piece of soft timber under the blanket fabric, punch a hole with the wad punch provided at each grommet location. Push male grommet component through hole. Place female component into position and tap gently together with a hammer. Loop the cord through either the single or double grommet and tie it off with a secure knot. Adjust the length of the cord by loosening the screw on the tube a little, until you can move the cord and then tighten it when the length is correct. Variations in the length of the cord will effect how straight the blanket rolls up, so it is important to adjust the length carefully. If you test roll the blanket onto the tube and it rolls unevenly, unroll it, adjust the length of the cords and roll it again until the blanket rolls evenly.12. Fitting your overcover. The Tube kit has been supplied with a protective cover to use when the blanket has been rolled onto the tube. You will void the warranty of most pool blankets if you do not cover it when stored on a reel. Follow the separate instructions for fitting the grommets and fastening cords to the overcover. Be sure to cover the blanket every time it is rolled onto the tube.
WarrantyYour Endurance reel system is pro-rata warranted for up to 5 years on the frame, tube and moulded plasticcomponents against faulty workmanship. If you find a component is faulty, post it pre-paid to: Hydrotools P/L,PO BOX 2037, Crestmead, Qld 4132 with a copy of your proof of purchase. A replacement will be sent you, andpriced based on the age of the Reel. (e.g. If the Reel is only 2 years old, the part will be supplied at 2/5 of thecurrent retail price.
Cord andwasher andscrewon tube
Twist tubesto removeexcess play
prior toscrewingtogether
Diagram 5
Diagram 7
Diagram 6
Diagram 8
Diagram 9
4
Frequently asked questionsThe tube has a small dent in it, will this effect the performance of the reel? Provided the tube remains straight, the performance will not be effected by a dent or mark on the tube.How can I move the reel when the blanket is stored on it? Your advanced reel system can be outfitted with heavy-duty castors (optional) and can then be easily rolled about.Where do I position the reel when I have to fold a section of my blanket? Position the reel at the opposite end to any section of the blanket that needs to be folded when stored on the reel. The fold creates an extra thickness on one side that will cause the blanket to roll unevenly and therefore this should be kept to a minimum.
4
PO Box 2037, Crestmead, Queensland 4132 Australia
Home Page: www.hydrotools.com.au Email: [email protected]
Hydrotools Pty. Ltd.ACN 107 829 603 ABN 45 107 829 603
Note: Reel styles may vary
LockCollar
Bolt &Lock Nut
Plastic Plug
Stand
AllenScrew
AllenWrench
Axle
Plastic Plug
AluminiumTubing
Slides OntoTube Insert
And is fastenedwith 3 self-drillingscrews per side
LockCollar
Bolt &Lock Nut
Plastic Plug
Depending upon your tube set you may also have:
HandWheel
HandWheel
Aluminium TubeInsert
Assemble toHand Wheel& Axel With
Bolt & Lock Nut
Aluminium TubeInsert
Assemble toHand Wheel& Axel With
Bolt & Lock Nut
Stand
AllenScrew
AllenWrench
Axle
Plastic Plug
Preparation And AssemblyCheck that you have all the items and assemble as illustrated below:
Thank you for purchasing a Hydrotools Pool Roller (reel). Please follow the instructions carefully to protect your warrantyand enjoy years of hassle-free use.
Please use your pool blanket and reel in the manner it was intended for:• Your pool blanket is not a safety cover
• Remove the pool blanket and reel assembly from the pool completely before swimming.
• Do not store the pool blanket on the ground in direct sunlight, as it will shorten the life of the blanket and maydamage your lawn.
• Always cover your pool blanket with the overcover supplied, when it is stored on the reel.
Positioning The Pool RollerFor rectangular pools, place Reel at either end of thepool.
For irregular shaped pools, place Reel at the widestpoint of the pool. You will need to fasten the blanket soit unwinds in two directions. Refer Diagram 2 & Item 11.
Fitting The BlanketFollow the instructions supplied with your pool blanket and fit it to the pool before you attach the blanket to the tube.The blanket will be easier to remove from pool your if it has been trimmed to the exact size of the pool. Small gapsat the edges do not affect the function of the pool blanket. Some pool blankets are trimmed larger than the size of thepool to prevent leaves and debris from entering the water. These can still be used with a storage reel, but can be alittle more difficult to operate due to the extra drag caused by the excess material when handling.
Assembling The Tube SetAll tube sets consist of 6-sided hexagonal-shaped aluminium tubes. There are two diameters of tube.In order for the Hand Wheel to drive and rotate the reel system you must first align the Hand Wheel to engagethe aluminium Tube Insert. Next, you must properly align the aluminium Tube Insert to engage the teeth insidethe small aluminium Tube. Refer Diagram 3.
Note: There may be tube plugs left over afterassembly of the tubes, depending on the sizeof the tube set you purchased.
We recommend that your pool reel be a minimum of300 mm wider than your pool blanket. See diagram 2 forinformation on positioning, so it rolls on more easily.
MediumAluminium Tube Insert
LargeAluminium Tube Insert
Additional Parts Supplied With Stand Sets:
1. Position stand & wheel assembly on the pool where the reel will operate.2. Loosely assemble the tubes together. Slide any excess width into adjoining tubes, dividing it up as equally as possible. Note: You must have a minimum of 230 mm overlap in each tube.3. Using the tubes, measure the width across the pool from plug surface to plug surface.4. Adjust the total length of the tube assembly to fit the span ensuring the minimum overlap of 230 mm. Refer Diagram 4
Unroll Unroll Unroll
Rectangular Irregular
Diagram 2
End ViewSmall
aluminiumTube
End ViewSmall
aluminiumTube Insert
aluminiumTube
insert mustengageteeth
inside smallaluminium
Tube!
Diagram 3
Diagram 4
Minimum230 mmOverlap
Measure Plug Surface To Plug Surface
Note: Depending uponyour pole set you may
also have largertube inserts
A: BlanketsUnder 40 m2
Fasten tubestogether using
six (6)screws in
staggered line,in each tube end
B: BlanketsOver 40 m2
Fasten tubestogether using
twelve (12)screws in
every hole,in each tube end
Fasten tube toAluminium Insertusing three (3)
Self-drilling screws(Refer Diagram 6
Next Page)
Fasten tube toAluminium Insertusing three (3)
Self-drilling screws(Refer Diagram 6
Next Page)
32
Plastic grommet Cord Quick-release Pin
AssemblyYou will assemble the Aluminium Tube Insert to the Hand Wheel and Axle by lining up the holes in all 3 parts. InsertBolt through the hole and securely tighten bolt with lock nut using screw driver. Insert the Wheel and Axle assembly throughthe bearing in the upright stand and secure lock collar with provided Allen wrench and set-screw.Next, you will use a series of pre-drilled holes, spaced approximately 38 mm and 190 mm from each end, to join the largetube to the small tube. There are holes provided at each join. These will be secured with self-drilling stainless steelscrews and the Hex-head screw driver bit later in Step 8. You can identify the end tubes by the three holes used tofasten them into the Hand Wheels. You will make this connection later in Step 9.
EPDM domed washer
Top ViewStand
Top ViewStand
Wheel Wheel
NOTE:After proper allignment,push Tube hard against
Handwheel when fastening
SetScrew
SetScrew
Driver Bit(Hexagon Head)
Self Drill Screw(Hexagon Head)
Item#
Parts List / Refer To Your Item Number
Standard withS/S Bearing
22” Fixed
22” Fixed
22” Adjustable
22” Adjustable
22” Adjustable
With 3”Hub
With 4”Hub
With 4”Hub
With 5”Hub
With 4”Hub
2 Pcs X 6”
2 Pcs X 6”
2 Pcs X 6”
2 Pcs X 12”
2 Pcs X 12”
2
2
2
2
2
2
2
2
1
1
1
1
1
13
13
13
13
13
2 Pcs. X 2.375”
2 Pcs. X 2.75”
2 Pcs. X 2.75”
2 Pcs. X 3”
2 Pcs. X 3”
1
1
1
1
1
24
24
24
24
24
12
12
12
12
12
1 1
1 1
1 1
1 1
1 1
2 Pcs 18” Wheel
Aluminum Assemb. Axel & Insert
(HCR14) w/2 screws
AluminumCollar(HCR14)
AllenWrench Bolt & Nut
QuickRelease
Pin
Driver Bit(Hexagon Head)
BlueGrommet
EPDMWasher
20m #20White Cord Instruction
Self DrillScrew
Hexagon Head
A1
A2
B2
B3
E6