color cctv camera wv-cf112e -...

2
THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THE THIRD PARTY'S RIGHT. THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S). Limitation of liability IN NO EVENT SHALL Panasonic System Networks Co., Ltd. BE LIABLE TO ANY PARTY OR ANY PERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE CASES, INCLUDING BUT NOT LIMITED TO BELOW: (1) ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT, SPECIAL, CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE PRODUCT; (2) PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE USER; (3) UNAUTHORIZED DISASSEMBLE, REPAIR OR MODIFICATION OF THE PRODUCT BY THE USER; (4) INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED, DUE TO ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT; (5) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISING OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY; (6) ANY CLAIM OR ACTION FOR DAMAGES, BROUGHT BY ANY PERSON OR ORGANIZATION BEING A PHOTOGENIC SUBJECT, DUE TO VIOLATION OF PRIVACY WITH THE RESULT OF THAT SURVEILLANCE-CAMERA'S PICTURE, INCLUDING SAVED DATA, FOR SOME REASON, BECOMES PUBLIC OR IS USED FOR ANY PURPOSE. Disclaimer of warranty Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Only use attachments/accessories specified by the manufacturer. 10) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 11) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Operating Instructions Color CCTV Camera Model No. WV-CF112E Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number is abbreviated in some descriptions in this manual. We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standard or other normative document following the provisions of Directive 2004/108/EC. WARNING: • To prevent fire or electric shock hazard, do not expose this apparatus to rain or moisture. • To prevent injury, this apparatus must be securely attached to the floor/wall/ceiling in accordance with the installation instructions. • The installation shall be carried out in accordance with all applicable installation rules. • This product has no power switch. When turning off the power, turn off a Power Supply or remove a power cable. • The connections should comply with local electrical code. S3125A This product is a 1/3-type CCD color CCTV camera. Connection of this product to a video monitor allows users to use this product as a monitoring camera. Preface Introduction of newly developed high-resolution CCD The introduction of the newly developed CCD with 976 horizontal pixels has led to a horizontal resolution of as high as 600 TV lines. High sensitivity achieved because of noise reduction function Sensitivity at the following minimum illuminations has been accomplished for color images because of the introduction of low noise circuit design (F1.4): 0.07 lx (black-and-white) Day/Night conversion function equipped No setup change is required at night because the image automatically changes from the color mode to the black-and-white mode at low illuminance. Main functions Refer installation work to the dealer. Installation work requires technique and experiences. Otherwise injury, or damage to this product may result. Be sure to consult the dealer. Do not insert any foreign objects. This could permanently damage this product. Turn the power off immediately and contact qualified service personnel for service. Do not attempt to disassemble or modify this product. Failure to observe this may cause fire or electric shock. Consult the dealer for the repair or inspections. Stop operation immediately when something is wrong with this product. When smoke goes up from this product or the smell of smoke comes from this product, con- tinued use will result in fire, injury, or damage to the product. Turn the power off immediately and contact qualified service personnel for service. Select an installation area that can support the total weight. Selecting an inappropriate installation surface may cause the product to fall down or topple over, resulting in injury. Installation work shall be started after sufficient reinforcement. Periodic inspections shall be conducted. Rust on the metal parts or screws may cause the product to fall down resulting in injury or accidents. Consult the dealer for the inspections. This product shall be installed in a vibration-free place. Failure to observe this may cause screws and bolts to be loosened and consequently to fall resulting in injury. Install this product in a location high enough to avoid people and objects from bump- ing the product. Failure to observe this may cause a drop resulting in injury or accidents. Do not strike or give a strong shock to this product. Failure to observe this may cause injury or fire. Turn the power off when do wiring of this product. Failure to observe this may cause electric shock. A short circuit or wrong wiring may cause fire. Do not use this product in an atmosphere of flammable gases. Failure to observe this may cause injury by explosion. Avoid installing this product in locations where it is subject to damage by salt or corrosive gas. Otherwise the mounting fixtures will deteriorate, causing the product to fall down and leading to accidents. Tighten screws and mounting fixtures to the specified torque. Failure to observe this may cause a drop resulting in injury or accidents. Precautions [Precautions for use] This product is designed to be used indoors. This product is not operable outdoors. This product has no power switch. When turning off the power, turn off a circuit breaker. To keep on using with stable performance Parts of this product may deteriorate and it may shorten the lifetime of this product when using in locations subject to high temperatures and high humidity. (Recommended operating temperature: +35 °C or lower) Do not expose this product to direct heat sources such as a heater. Handle this product with care. Do not drop this product, nor apply shock or vibration to this product. Failure to observe this may cause trouble. Do not touch the dome cover with your bare hands. A dirty dome cover causes deterioration of picture quality. Noise on monitor This product is equipped with a super sensitive CCD. Therefore, noise may appear on the monitor. This phenomenon is not trouble. Discoloration on the CCD color filter When continuously shooting a bright light source such as a spotlight, the color filter of the CCD may have deteriorated and it may cause discoloration. Even when changing the fixed shooting direction after continuously shooting a spotlight for a certain period, the discoloration may remain. Do not aim this product at strong light sources. A light source such as a spot light causes a blooming (light bleeding) or a smear (vertical lines). Cleaning this product body Turn the power off when cleaning this product. Do not use strong abrasive detergent when cleaning this product. Otherwise, it may cause discoloration. Synchronous mode setting Image synchronous mode of this camera indicates internal synchronization (INT) only. Set the multiplex vertical driver (VD2) as OFF when the camera is connected to the system controller of the company. Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this docu- mentation. This product is designed to be used indoors. This product is not operable outdoors. Do not expose the product to direct sunlight for hours and do not install the product near a heater or an air conditioner. Otherwise, it may cause deformation, discoloration and malfunc- tion. Keep the product away from water and moisture. Installing place Contact your dealer for assistance if you are unsure of an appropriate place in your particular environment. Make sure that the installation area is strong enough to hold the product, such as a con- crete ceiling. Install the camera in the foundation area of the architecture or where sufficient strength is assured. If a ceiling board such as plaster board is too weak to support the total weight, the area shall be sufficiently reinforced. Avoid installing this product in the following locations. Location where it may get wet from rain or water splash. Locations where a chemical agent is used such as a swimming pool. Locations subject to steam and oil smoke such as a kitchen. Locations near flammable gas or vapor. Locations where radiation or x-ray emissions are produced. Locations where corrosive gas is produced, Locations where it may be damaged by briny air such as seashores. Locations where the temperature is not within –10 °C to +50 °C. Locations subject to vibrations (This product is not designed for on-vehicle use.) Locations subject to condensation as the result of severe changes in temperature (In case of installing the product in such locations, the dome cover may become foggy or conden- sation may be caused on the cover.) Avoid moist or dusty places to install this system. Otherwise, lifetime of the internal parts may be shortened. Avoid installing this product in a place with a high level of noise. Installation near an air conditioner, an air cleaner, a vending machine, or the like causes noise. Avoid installing and connecting during a lightning storm. Otherwise, an electric shock or fire may be caused. Be sure to remove this product if it is not in use. Do not damage the power plug or cable. Keep the camera cable away from the lighting cable. Failure to observe this may cause noise. Precautions for installation Smear Bright subject Blooming q Video output connector Transmits composite video signals. w Mark This mark is used when the dome cover is installed. e Lens r Tilting lock screw Fixes the tilting position. t Panning table lock screw [LOCK] Locks the panning position after adjustment. y Tilting table Adjusts the tilting position of the camera. u Panning table Adjusts the panning position of the camera. i Cable access hole o Power cord Supplies 12 V DC from an external power source. !0 Dust guard cap A rubber cap which prevent dust go into the camera through the cable access hole. !1 Fingerplate This is where to put your fingers when removing the dome cover. Major operating controls and their functions q o t r y u w e !1 !0 i !1 !1 LOCK LOCK Important: Procure 2 screws (M4) to secure the camera to a ceiling according to the material of the installation area. Do not use wood screws and nails. For mounting a camera on a con- crete ceiling, use an anchor bolt (M4) for securing. (Recommended tightening torque M4: 1.6 N·m) Required pull-out strength of a single screw/bolt is 196 N or more. If a ceiling board such as plaster board is too weak to support the total weight, the instal- lation area shall be sufficiently reinforced. The protection sheet attached to the dome section should be peeled off after installation. The mounting conditions of the camera are described as follows: Installation place Applicable mount bracket Recommended screw Number of screw Minimum pull-out strength (per 1 pc.) Ceiling (Direct mounting) M4 2 pcs. 196 N Preparations Remove the dome cover q Peel off the protection sheet from the dome cover. Don't remove completely as this protects the dome during instal- lation. w Adjust the mark on this camera to [ || ] on the dome cover, and lift up the dome cover for approx. 10 mm. Then, turn the dome cover counterclockwise to align the mark on the camera to [ | ] on the dome cover as shown in the illustration. The dome cover can be removed from the camera on this position. Note: The clear dome cover and the dome cover are joined into a single unit. Therefore, never try to remove them. Do not try to remove the dome cover forcibly on the [ || ] position. Remove the dome cover after turning it to the [ | ] position. Mark Mark [ | ] Panasonic Corporation http://panasonic.net Panasonic Systems Asia Pacific 2 Jalan Kilang Barat, Panasonic Building, Singapore 159346 Panasonic India Pvt. Ltd. 5th Floor, ABW Tower, Near IFFCO Chowk, Sector-25, Gurgaon, Haryana, 122001, India Importer's name and address to follow EU rules: Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15, 22525 Hamburg F.R.Germany © Panasonic System Networks Co., Ltd. 2012 Ns0512-0 PGQX1196ZA Printed in China Radio interference When the camera is used near TV/radio antenna, strong electric field or magnetic field (near a motor or a transformer), images may be distorted and noise sound may be produced. In such a case, run the camera cable through specialized steel conduit tubes. Locally procure the screws Screws are not supplied with this product. Prepare the screws according to the material, structure, strength and other factors of the mounting area and the total weight of objects to be mounted. Screw tightening The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the installation area. Do not use an impact driver. Failure to observe this may cause overtightening and conse- quently damage to the screws. When a screw is tightened, make the screw at a right angle to the surface. After tighten- ing the screws or bolts, perform visual check to ensure tightening is enough and there is no backlash.

Upload: letuyen

Post on 14-May-2018

219 views

Category:

Documents


2 download

TRANSCRIPT

Page 1: Color CCTV Camera WV-CF112E - ssbu-t.psn-web.netssbu-t.psn-web.net/Products/Analogue_camera/WV-CF112/Manual/PG… · Install in accordance with the manufacturer's instructions. 8)

THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THE THIRD PARTY'S RIGHT.THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).

Limitation of liability

IN NO EVENT SHALL Panasonic System Networks Co., Ltd. BE LIABLE TO ANY PARTY OR ANY PERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE CASES, INCLUDING BUT NOT LIMITED TO BELOW:(1) ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT,

SPECIAL, CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE PRODUCT;

(2) PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE USER;

(3) UNAUTHORIZED DISASSEMBLE, REPAIR OR MODIFICATION OF THE PRODUCT BY THE USER;

(4) INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED, DUE TO ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;

(5) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISING OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY;

(6) ANY CLAIM OR ACTION FOR DAMAGES, BROUGHT BY ANY PERSON OR ORGANIZATION BEING A PHOTOGENIC SUBJECT, DUE TO VIOLATION OF PRIVACY WITH THE RESULT OF THAT SURVEILLANCE-CAMERA'S PICTURE, INCLUDING SAVED DATA, FOR SOME REASON, BECOMES PUBLIC OR IS USED FOR ANY PURPOSE.

Disclaimer of warranty

Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's

instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat. 9) Only use attachments/accessories specified by the manufacturer. 10) Use only with the cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

11) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Operating InstructionsColor CCTV Camera

Model No. WV-CF112E

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.

The model number is abbreviated in some descriptions in this manual.

We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standard or other normative document following the provisions of Directive 2004/108/EC.

WARNING:• To prevent fi re or electric shock hazard, do not expose this apparatus to rain or

moisture.• To prevent injury, this apparatus must be securely attached to the fl oor/wall/ceiling in

accordance with the installation instructions.• The installation shall be carried out in accordance with all applicable installation rules.• This product has no power switch. When turning off the power, turn off a Power Supply or remove a power cable.• The connections should comply with local electrical code.

S3125A

This product is a 1/3-type CCD color CCTV camera. Connection of this product to a video monitor allows users to use this product as a monitoring camera.

Preface

Introduction of newly developed high-resolution CCDThe introduction of the newly developed CCD with 976 horizontal pixels has led to a horizontal resolution of as high as 600 TV lines.

High sensitivity achieved because of noise reduction functionSensitivity at the following minimum illuminations has been accomplished for color images because of the introduction of low noise circuit design (F1.4): 0.07 lx (black-and-white)

Day/Night conversion function equipped No setup change is required at night because the image automatically changes from the color mode to the black-and-white mode at low illuminance.

Main functions

Refer installation work to the dealer.Installation work requires technique and experiences. Otherwise injury, or damage to this product may result.Be sure to consult the dealer.

Do not insert any foreign objects.This could permanently damage this product.Turn the power off immediately and contact qualified service personnel for service.

Do not attempt to disassemble or modify this product.Failure to observe this may cause fire or electric shock.Consult the dealer for the repair or inspections.

Stop operation immediately when something is wrong with this product.When smoke goes up from this product or the smell of smoke comes from this product, con-tinued use will result in fire, injury, or damage to the product.Turn the power off immediately and contact qualified service personnel for service.

Select an installation area that can support the total weight.Selecting an inappropriate installation surface may cause the product to fall down or topple over, resulting in injury.Installation work shall be started after sufficient reinforcement.

Periodic inspections shall be conducted.Rust on the metal parts or screws may cause the product to fall down resulting in injury or accidents.Consult the dealer for the inspections.

This product shall be installed in a vibration-free place.Failure to observe this may cause screws and bolts to be loosened and consequently to fall resulting in injury.

Install this product in a location high enough to avoid people and objects from bump-ing the product.Failure to observe this may cause a drop resulting in injury or accidents.

Do not strike or give a strong shock to this product.Failure to observe this may cause injury or fire.

Turn the power off when do wiring of this product.Failure to observe this may cause electric shock. A short circuit or wrong wiring may cause fire.

Do not use this product in an atmosphere of fl ammable gases.Failure to observe this may cause injury by explosion.

Avoid installing this product in locations where it is subject to damage by salt or corrosive gas.Otherwise the mounting fixtures will deteriorate, causing the product to fall down and leading to accidents.

Tighten screws and mounting fi xtures to the specifi ed torque.Failure to observe this may cause a drop resulting in injury or accidents.

Precautions

[Precautions for use]

This product is designed to be used indoors.This product is not operable outdoors.

This product has no power switch.When turning off the power, turn off a circuit breaker.

To keep on using with stable performanceParts of this product may deteriorate and it may shorten the lifetime of this product when using in locations subject to high temperatures and high humidity. (Recommended operating temperature: +35 °C or lower)Do not expose this product to direct heat sources such as a heater.

Handle this product with care.Do not drop this product, nor apply shock or vibration to this product.Failure to observe this may cause trouble.

Do not touch the dome cover with your bare hands.A dirty dome cover causes deterioration of picture quality.

Noise on monitorThis product is equipped with a super sensitive CCD. Therefore, noise may appear on the monitor. This phenomenon is not trouble.

Discoloration on the CCD color fi lterWhen continuously shooting a bright light source such as a spotlight, the color filter of the CCD may have deteriorated and it may cause discoloration. Even when changing the fixed shooting direction after continuously shooting a spotlight for a certain period, the discoloration may remain.

Do not aim this product at strong light sources.A light source such as a spot light causes a blooming (light bleeding) or a smear (vertical lines).

Cleaning this product bodyTurn the power off when cleaning this product.Do not use strong abrasive detergent when cleaning this product. Otherwise, it may cause discoloration.

Synchronous mode settingImage synchronous mode of this camera indicates internal synchronization (INT) only. Set the multiplex vertical driver (VD2) as OFF when the camera is connected to the system controller of the company.

Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this docu-mentation.

This product is designed to be used indoors.This product is not operable outdoors.Do not expose the product to direct sunlight for hours and do not install the product near a heater or an air conditioner. Otherwise, it may cause deformation, discoloration and malfunc-tion. Keep the product away from water and moisture.

Installing placeContact your dealer for assistance if you are unsure of an appropriate place in your particular environment.

Make sure that the installation area is strong enough to hold the product, such as a con-•crete ceiling.Install the camera in the foundation area of the architecture or where suffi cient strength is •assured.If a ceiling board such as plaster board is too weak to support the total weight, the area •shall be suffi ciently reinforced.

Avoid installing this product in the following locations.Location where it may get wet from rain or water splash.•Locations where a chemical agent is used such as a swimming pool.•Locations subject to steam and oil smoke such as a kitchen.•Locations near fl ammable gas or vapor.•Locations where radiation or x-ray emissions are produced.•Locations where corrosive gas is produced, Locations where it may be damaged by briny •air such as seashores.Locations where the temperature is not within –10 °C to +50 °C.•Locations subject to vibrations (This product is not designed for on-vehicle use.)•Locations subject to condensation as the result of severe changes in temperature (In case •of installing the product in such locations, the dome cover may become foggy or conden-sation may be caused on the cover.)

Avoid moist or dusty places to install this system.Otherwise, lifetime of the internal parts may be shortened.

Avoid installing this product in a place with a high level of noise.Installation near an air conditioner, an air cleaner, a vending machine, or the like causes noise.

Avoid installing and connecting during a lightning storm. Otherwise, an electric shock or fi re may be caused.

Be sure to remove this product if it is not in use.

Do not damage the power plug or cable.

Keep the camera cable away from the lighting cable.Failure to observe this may cause noise.

Precautions for installation

Smear Bright subject

Blooming q Video output connector Transmits composite video signals.w Mark This mark is used when the dome cover is installed.e Lensr Tilting lock screw Fixes the tilting position.t Panning table lock screw [LOCK] Locks the panning position after adjustment.y Tilting table Adjusts the tilting position of the camera.u Panning table Adjusts the panning position of the camera.i Cable access holeo Power cord Supplies 12 V DC from an external power source.!0 Dust guard cap A rubber cap which prevent dust go into the camera through the cable access hole.!1 Fingerplate This is where to put your fingers when removing the dome cover.

Major operating controls and their functions

q o

t

r

y

u

w

e !1

!0

i

!1

!1

LOCK

LOCK

Important:Procure 2 screws (M4) to secure the camera to a ceiling according to the material of the •installation area. Do not use wood screws and nails. For mounting a camera on a con-crete ceiling, use an anchor bolt (M4) for securing.(Recommended tightening torque M4: 1.6 N·m)Required pull-out strength of a single screw/bolt is 196 N or more.•If a ceiling board such as plaster board is too weak to support the total weight, the instal-•lation area shall be suffi ciently reinforced.The protection sheet attached to the dome section should be peeled off after installation.•

The mounting conditions of the camera are described as follows:

Installation place

Applicable mount bracket

Recommended screw

Number of screw

Minimum pull-out strength (per 1 pc.)

Ceiling (Direct mounting) M4 2 pcs. 196 N

Preparations

■ Remove the dome coverq Peel off the protection sheet from the

dome cover. Don't remove completely as this protects the dome during instal-lation.

w Adjust the mark on this camera to [ || ] on the dome cover, and lift up the dome cover for approx. 10 mm. Then, turn the dome cover counterclockwise to align the mark on the camera to [ | ] on the dome cover as shown in the illustration. The dome cover can be removed from the camera on this position.

Note:The clear dome cover and the • dome cover are joined into a single unit.

Therefore, never try to remove them.Do not try to remove the dome cover •forcibly on the [ || ] position. Remove the dome cover after turning it to the [ | ] position.

Mark

Mark [ | ]

Panasonic Corporationhttp://panasonic.net

Panasonic Systems Asia Pacific2 Jalan Kilang Barat, Panasonic Building, Singapore 159346Panasonic India Pvt. Ltd.5th Floor, ABW Tower, Near IFFCO Chowk, Sector-25, Gurgaon, Haryana, 122001, India

Importer's name and address to follow EU rules:Panasonic Testing CentrePanasonic Marketing Europe GmbHWinsbergring 15, 22525 Hamburg F.R.Germany

© Panasonic System Networks Co., Ltd. 2012

Ns0512-0 PGQX1196ZA Printed in China

Radio interferenceWhen the camera is used near TV/radio antenna, strong electric field or magnetic field (near a motor or a transformer), images may be distorted and noise sound may be produced.In such a case, run the camera cable through specialized steel conduit tubes.

Locally procure the screwsScrews are not supplied with this product.Prepare the screws according to the material, structure, strength and other factors of the mounting area and the total weight of objects to be mounted.

Screw tighteningThe screws and bolts must be tightened with an appropriate tightening torque according •to the material and strength of the installation area.Do not use an impact driver. Failure to observe this may cause overtightening and conse-•quently damage to the screws.When a screw is tightened, make the screw at a right angle to the surface. After tighten-•ing the screws or bolts, perform visual check to ensure tightening is enough and there is no backlash.

Page 2: Color CCTV Camera WV-CF112E - ssbu-t.psn-web.netssbu-t.psn-web.net/Products/Analogue_camera/WV-CF112/Manual/PG… · Install in accordance with the manufacturer's instructions. 8)

■ About the side cable access holeIf you choose not to drill hole in the ceil-ing, but to wire the camera with the cable exposed, cut the cable access hole on the side of the dome cover to provide a cable entry.

Note:Cut out the part as show in the illus-•tration.

Precautions when wiring from the side:Move the cable to one side as shown.•Be careful not to pinch the cable with •the dome cover.

Installing the camera directly on a ceiling

83.5 mm15 mm

Recommended screw (M4, 2 pcs.)

Cable mounting hole in ceiling

Screws (M4, locally procured)

LOC

K

Fron

t

Installation of cameraTurn off the power of all related devices before installation.

z Remove the camera dome cover.

x Connect all cables. If necessary, bind the cable with cable tie (locally procured).

c Install the camera. Mount the camera with 2 screws (M4, locally procured).

Important:Be sure to avoid twisting the cables when tightening the screws.•

Note:When attached to the ceiling:•

Install the camera with its front (Model number indication face) facing the same direction as the “gFRONT” arrow of the installation mark.

Installation

■ Pan and tilt adjustment

Important:When adjusting pan or tilt, do not hold the lens of the camera.•

q Adjustment of panning position Loosen the panning table lock screw and rotate the table to determine the

panning position (adjustable range: 350°).The panning position can be adjusted between +180° (clockwise) and –170° (counter-•clockwise).After the panning position is determined, fix the panning table with the panning table lock •screw. (Recommended torque: 0.59 N·m)

w Adjustment of tilting position Turn the tilting table to adjust the tilting position of the camera. (adjustable

range: +75 °)After the tilting position is determined, fix the tilting table with the tilting lock screw.•Tighten the tilting lock screw after adjustment. (Recommended torque: 0.• 59 N·m)

Note:The• image top mark is facing “ΔTOP” to display the image.

Adjustment

Counter-clockwise: –170 º

Panning table

Clockwise: +180 º

Original position markPanning table lock screw [LOCK]

LOCK

LOCK

Adjustable range: +75 º, 0 º

Image top mark

LOCK

■ ConnectionsConnect the coaxial cable (locally procured)

Important:Be sure to turn off the power of each device before connecting.•Be sure to secure the coaxial cable connectors.•

Connect a coaxial cable to the video output connector.

Connect the power supplyConnect the two-color conductor cable of the camera to the power supply. The colors and functions of the conductors are shown below.

Color 12 V DCRed PositiveBlack Negative

Important:The power supply of 12 V DC shall be insulated against 220 to 240 V AC.•

Power cord(DC INLINE JACK PLUG TYPE: ø5.5×2.1)

Video output connector

LOCK

LOCK

Use a pen to mark the positions of the screws and cable mounting hole in the ceiling.Attach the camera with 2 screws (M4, locally procured).

z Align the mark with [ | ] on the dome cover, and then install the dome cover.

x Adjust the orientation of the dome cover. Turn the dome cover clockwise until the mark aligns with [ || ] and a click is heard. Turn the dome cover to the left or right while viewing the monitor so that the light is not

blocked.

Important:Be sure to align the mark with [ • || ] when adjusting the dome cover. Do not apply exces-sive force, or you may cause damage.

c Lift up the dome cover and then turn it clockwise until the mark aligns with [ ||| ] and a click is heard.

v After finishing the installation, completely peel off the protection sheet that had been retained on the camera.

Attaching the dome cover

Mark

Mark [ | ]

Opening (approx. 10 mm)

Mark [ || ]

Mark [ ||| ]

Before asking for repairs, confirm the causes with the following table.Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below.

Symptom Cause/solution

No image displayed Are the power cord and coaxial cable connected •appropriately?

Check whether the connection is appropriately →established.

Is the adjustment monitor connected?•Confirm whether the monitor is connected. →

Is the monitor brightness appropriately adjusted, or is •the contrast appropriately adjusted?

Check whether the monitor settings are → appro-priate.

Is the cushioning material in the spherical cover •removed?

Confirm whether the cushioning material has →been removed.

Blurred image Is the spherical cover dirty or damaged?•Verify the state of the spherical cover. →

Is the focus adjusted correctly?•Check if the focus is adjusted correctly. →

Is the lens of the camera soiled with dirt or dust?•Check whether the lens of the camera is clean. →

Black line in image Is the connected system controller set to multiplexed •vertical drive (VD2)?

Check whether the connected system controller →is set correctly.

Damaged power cord sheathing

The power cord or connector is damaged. •Continuous use of the damaged cord or connector may cause electric shock or fire. Turn off the power supply immediately and request repair from your dealer.

Heated portion of power line con-sisting of power cord and con-nector during use

The temperature of power cord rises or falls when the power cord is bent or stretched during use

Troubleshooting

Power source 12 V DCPower consumption 12 V DC: 120 mAImage sensor 1/3-type interline transfer CCDEffective pixels 976 (H)×582 (V)Scanning area 4.8 mm (H)×3.6 mm (V)Scanning system 2:1 interlaceScanning line 625 linesHorizontal scanning frequency 15.625 kHzVertical scanning frequency 50.00 HzSynchronization Internal (INT)Horizontal resolution 600 TV linesVertical resolution 400 TV linesVideo output 1.0 V [p-p] PAL composite video signal 75 ΩSignal-to-noise ratio 52 dB (AGC OFF)Minimum illumination 0.08 lx (color mode) at F1.4

0.07 lx (black-and-white mode) at F1.4 * corresponding value

Lens Fixed LensFocal length 3.6 mmAperture ratio F1.8View angle 77 ° (H) × 57 ° (V)Adjustable angle range Pan: +180 ° to –170 °

Tilt: +75 ° to 0 °Ambient operating temperature –10 °C to +50 °CAmbient operating humidity Less than 90 %Dimensions ø108 mm × 88 mm (H)Mass 200 gLight control mode ELC (Auto IRIS)Auto black stretch (ABS) ONAuto gain control ONWhite balance ATWDigital noise reduction ONDay & Night (Electric) AUTO

Values of weight and dimensions are approximate. The specification is subject to change * without notice.

Auto black stretch [ABS]The latest digital signal technology is applied to automatically detect the dark areas in the image, acquire the brightness data around the dark areas, and perform real-time color adjust-ment by calculating the best correction curve for each area. This function can be used to per-form real-time adjustment and correction of back light and dark area, and reproduce natural, clear images.

Auto gain control [AGC]Automatically increases the gain to make the screen brighter when the illuminance of the sub-ject becomes darker.

Auto tracking white balance [ATW]Activates the automatic color temperature tracking mode.The camera continuously check the color temperature of the light source and automatically adjusts the white balance. The adjustment of the color temperature ranges from approx. 2700 K to 6000 K.

Digital noise reduction [DNR]The digital noise reduction function reduces noise automatically under the condition of low illu-minance.

Day & Night (Electric) [D&N (ELE)]Automatically switches between color and black-and-white images in accordance with the illu-minance. Switches to black-and-white images when the illuminance around the camera is lower than approx. 0.07 lx at F1.4 *corresponding valueTo obtain color images, a sufficient level of illuminance (approx. 3.0 lx at F1.4 *corresponding value) is required.The switching illuminances described above are reference values. The switching illuminance shall be decided based on the actual installation environment.There may be repeated switching between color and black-and-white images depending on the setting and environment.

Specifications

Operating Instructions (this document) ......... 1 pc.

Standard accessories

Connection of power cordWhen connecting the power cord, use connectors that are designed for the power cord, and be careful not to let the power cord fall off.In addition, waterproofing work is needed at the joint, e.g., wrapping waterproof tape around the joint.

Cable length and wire gauge12 V DCCalculation of the relation among the cable length, resistance, and power supply.The voltage supplied to the camera shall be between 10.8 V DC and 16 V DC.10.8 V DC ≤ VA - 2 (R x I x L) ≤ 16 V DCL : Cable length (m)R : Resistance of copper wire (Ω/m)VA : DC output voltage of power supply unitI : DC current consumption (A)

See specifications.Resistance of copper wire [at 20 °C]

Copper wire size (AWG)

#24(0.205 mm2)

#22(0.325 mm2)

#20(0.519 mm2)

#18(0.833 mm2)

#16(1.307 mm2)

Resistance Ω/m 0.083 0.052 0.033 0.020 0.013

Side cable access hole