collated screw systems - starsales.comstarsales.com/pdf/star-sales-screws-and-fasteners.pdf ·...

154

Collated Screw Systems

DURASPIN® COLLATED SCREWS

Drywall to Wood — CoarsePart No. Description Qty.

GCS6125 1-1/4" 1MGCS6162 1-5/8" 1MDrywall to Light Steel — Sharp PointGFS6125 1-1/4" 1MGFS6162 1-5/8" 1M

Drywall to Steel — Self-DrillPart No. Description Qty.

GFD6125 1-1/4" Self-Drill 1M

Cement Board to WoodPart No. Description Qty.

CHN8125D 1-1/4" 1M

Stainless Steel ScrewsPart No. Description Qty.

DCT8250S 2-1/2" Wood 800DCT9300S 3" Wood 800DCT8200ST 2" Trim Head 1MDCT8250ST 2-1/2" Trim Head 800DCT9300ST 3" Trim Head 800

Interior Wood to Wood (*coarse thread w/wax lube)Part No. Description Qty.

SCS8150 1-1/2" 1MSCS8175 1-3/4" 1MSCS8200 2" 1MSCS8250 2-1/2" 800

All Purpose Exterior Wood to WoodPart No. Description Qty.

DCT8275D 1-3/4" 1M

DCT8200D 2" 1MDCT8250D 2-1/2" 800DCT8300D 3" 800

Composite Decking ScrewsPart No. Description Qty.TDS8250DI 2-1/2" Gray 800TDS8300DI 3" Gray 800

Need a Door and Frame taken off?

Check out our Full Service Door and

Frame Department.

154SS 5/19/10 3:59 PM Page 154

156

Air Tool Accessories

Nails and Accessories16 Gauge Straight Finish NailsPart No. Description Qty.

650281 1" Finish Nails 2M/Box650282 1-1/4" Finish Nails 2M/Box650283 1-1/2" Finish Nails 2M/Box650284 1-3/4" Finish Nails 2M/Box650285 2" Finish Nails 2M/Box650287 2-1/2" Finish Nails 2M/Box

Paslode Stick Nails BrightPart No. Description Qty. / Box650272 2" Bright Smooth 5.5 M650273 2" Bright Ring 5.5 M650237 2-3/8" Bright Smooth 5 M650238 2-3/8" Bright Ring 5 M650236 3" Bright Smooth 2.5 M650239 3-1/4" Bright Smooth 2.5 M097987 3-1/2" Bright Smooth 2.5 M

Paslode BatteriesPart No. Description

404717 CT Tool Oval (New)

402500 Stick Battery (Old)

900200 Battery Charger

Degreaser 1202Part No. Description219086 Degreaser 1202

401482 Oil403720 16 oz. Air Tool Oil

16 Gauge Angle Finish NailsPart No. Description Qty.

650230 1-1/4" Finish Nails 2M/Box650231 1-1/2" Finish Nails 2M/Box650047 2" Finish Nails 2M/Box650232 2-1/2" Finish Nails 2M/Box

Positive Placement NailsPart No. Description Qty.

650026 1-1/2" x .148 Bright Joist Nails 3M650014 1-1/2" x .148 Galvanized Joist Nails 3M650028 2-1/2" Bright Joist Nails 2M650198 2-1/2" Galvanized Joist Nails 2M

Paslode Stick Nails Galvanized Part No. Description

650380 2" Galvanized Smooth 2M650381 2" Galvanized Ring 2M650382 2-3/8" Galvanized Smooth 2M650383 2-3/8" Galvanized Ring 2M650384 3" Galvanized Smooth 2M650385 3" Galvanized Ring 2M650388 3-1/4" Galvanized Smooth 2M650476 3-1/2" Galvanized Smooth 2M

Fuel CellsPart No. Description Qty

650039 Yellow Short Cell 4 pk 24/case

816001 Yellow Tall Cell 2 pk 6 pk/case

816000 Red Tall Cell 2 pk 6 pk/case

156SS 5/19/10 3:59 PM Page 156

159

Fasteners

GENUINE FASTENERS

GENUINE FASTENERS

15 Gauge Bright Angle Finish NailsPart No. Description Qty.

DA15EPBN 1-1/4" 4MDA17EPB 1-1/2" 4MDA21EPB 2" 4MDA25EPB 2-1/2" 3M

15 Gauge Galvanized Angle Finish NailsPart No. Description Qty.DA15EABN 1-1/4" 4MDA21EABN 2" 4MDA25EAB 2-1/2" 3M

15 Gauge Stainless Steel Angle Finish NailsPart No. Description Qty.DA21EGBN 2" 2MDA25EGB 2-1/2" 1.2M

Senco 1/4" Crown Staples — L SeriesPart No. Description Qty.

L06BAB 3/8" Leg 10ML08BAB 1/2" Leg 10ML10BAB 5/8" Leg 5ML11BAB 3/4" Leg 5ML12BAB 7/8" Leg 5ML13BABN 1" Leg 5ML14BAB 1-1/8" Leg 5ML15BAB 1-1/4" Leg 5ML17BAB 1-1/2" Leg 5M

236A Micro PinsPart No. Description Qty.

A100509 1/2" 2.6MA100759 3/4" 2.6MA101009 1" 2.6MA101259 1-1/4" 2.6MA101509 1-1/2" 2.6MA109809 Assorted Package Nails 2.6M

Joist Hanger NailsPart No. Description Qty. / BoxM002262 1-1/2 x .131 2MM002266 2-1/2 x .148 1.5M

Senco 3/8" Crown Staples — M SeriesPart No. Description Qty.

M06BABN 3/8" Leg 10MM08BAB 1/2" Leg 10MM11BABN 3/4" Leg 5MM13BAB 1" Leg 5MM15BAB 1-1/4" Leg 10MM17BAB 1-1/2" Leg 10M

16 Gauge Straight Finish NailsPart No. Description Qty.

DCS16125 1-1/4" 2.5MDCS16150 1-1/2" 2.5MDCS16200 2" 2.5MDCS16250 2-1/2" 2.5M

16 Gauge Angle Finish NailsPart No. Description Qty.

DCA16125 1-1/4" 2.5MDCA16150 1-1/2" 2.5MDCA16200 2" 2.5MDCA16250 2-1/2" 2.5M

159SS 5/19/10 4:00 PM Page 159

199

Fasteners

APPLICATION AND PRODUCTLIGHT DUTY STEEL-TO-STEEL APPLICATIONS REPORT NO. 02701• #6, #8, #10, #12, and 1/4 diameter Teks® 1, 2, and 3 drill points• Hex, Pan, and Oval heads

MEDIUM DUTY STEEL-TO-STEEL APPLICATIONS REPORT NO. 02702• #12 and 1/4 diameter Teks 2 and 3 drill points• Hex head

HEAVY DUTY STEEL-TO-STEEL APPLICATIONS REPORT NO. 02703• #6, #8, #10, #12, and 1/4 diameter Teks® 1, 2, and 3 drill points• Hex, Pan, and Oval heads

LOW PROFILE ARCHITECTURAL APPLICATIONS REPORT NO. 02704• #10 and #12 diameter Teks 2 and Type A points• Pancake head

WOOD-TO-METAL APPLICATIONS REPORT NO. 02705• #10, #12, and 1/4 diameter Teks 3 and 4 drill points• Wafer and Phillips flat head and Phills Square-Driv® heads

METAL ROOF AND WALL APPLICATIONS REPORT NO. 02706• #10, #12, and 1/4 diameter Teks 1, 2, 3, 4, and 5 drill points• Hex with bonded washer

PREMIUM METAL ROOF/WALL APPLICATIONS REPORT NO. 02707• #10, #12, and 1/4 diameter Teks 1, 2, 3, 4, and 5 drill points• 1/4 and #17 diameter Type AB• Maxiseal® integral washer system

LONG LIFE METAL ROOF AND WALL APPLICATIONS REPORT NO. 02708#12 and 1/4 diameter Teks 1, 2, 3, and 5 drill points• 1/4 and #17 diameter Type AB

LIGHT/MEDIUM DUTY STEEL-TO-STEEL APPLICATIONS REPORT NO. 040101• #8, #10, #12, and 1/4 diameter 410 Stainless Steel Teks 3• Hex, Pan, and Oval heads

LIGHT/MEDIUM DUTY STEEL-TO-STEEL APPLICATIONS REPORT NO. 040102• #10, #12, and 1/4 diameter 410 Stainless Steel Teks 2 and 3 drill points• Hex with bonded washer

LIGHT/MEDIUM DUTY STEEL-TO-STEEL APPLICATIONS REPORT NO. 040601• #14 and #17 diameter Tappers• 304 Stainless Steel/Carbon Steel• Hex with or without bonded washer

HIGH TORQUE ZINC DIE CAST REPORT NO. 72100• #12, 1/4, and #17 diameter 1 and 2 drill points and Type AB• Hex with bonded washer

EXTERIOR RIGID INSULATION APPLICATIONS REPORT NO. 02709• #9 and #12 diameter, gimlet point Trugrip™ GT• Hex with or without bonded washer

SELECTOR GUIDE

199SS 5/19/10 4:29 PM Page 199

200

Fasteners

METAL-TO-WOOD APPLICATIONS REPORT NO. 02711• #9 and #12 diameter, gimlet point Trugrip™ GT• Hex with or without gimlet washer

METAL-TO-WOOD APPLICATIONS REPORT NO. 02712• #9 and #12 diameter gimlet point Scots® Trugrip™

PIPE FLASHING APPLICATIONS REPORT NO. 040701• Dekstrip™ expandable edged flashing

PIPE FLASHING APPLICATIONS REPORT NO. 030104• Dektite® EZI-Seal™ pipe flashing

PIPE FLASHING APPLICATIONS REPORT NO. 02714• Dektite® and Retrofit Dektite®

• EPDM and silicone for 1/4" to 24" pipes

METAL ROOF END CAP FLASHING APPLICATIONS REPORT NO. 02715• Dek-Cap™ standing seam roof end cap flashing

LIGHT/MEDIUM DUTY MASONRY APPLICATIONS REPORT NO. 02717• 3/16" and 1/4" diameter Tapcon® anchors• Hex and flat heads

LIGHT/MEDIUM DUTY MASONRY APPLICATIONS REPORT NO. 02718• 1/4" diameter Maxi-Set Tapcon® Anchors• 5/16" across flats hex with 5/8" diameter flange

EXTERIOR MASONRY APPLICATIONS REPORT NO. 02719• 1/4'' diameter Scots® Tapcon® Anchors• 300 Series Stainless Steel HWH integral washer system

CORROSIVE ENVIRONMENT MASONRY APPLICATIONS REPORT NO. 02720• 3/16" and 1/4" diameter stainless steel Tapcon® anchors• Hex and Phillips flat heads

HURRICANE PROTECTION REPORT NO. 060402• 1/4" diameter direct mount storm panel Tapcon anchors

HURRICANE PROTECTION REPORT NO. 060401• 3/16" and 1/4" diameter Sammys low profile hurricane shutter fastener

DRYWALL ANCHOR APPLICATIONS REPORT NO. 02721• E-Z Ancor®, E-Z Ancor® Stud Solver, Plastic Plus™, E-Z Toggle™, E-Z Lite™, E-Z Mini®

CEMENT BOARD APPLICATIONS REPORT NO. 02722• HI-LO® and S-12® Rock-On™ screws/Backer On™ screws• Countersinking wafer head

EXTERIOR WOOD APPLICATIONS REPORT NO. 02723• #6, #7, #8, and #10 diameter Dec-King™ screws

EXTERIOR INSULATED FINISH SYSTEM APPLICATIONS REPORT NO. 02724• Gridmate™ Eifs mechanical fasteners• Gridmate™ PB Eifs mechanical fasteners

SELECTOR GUIDE

200SS 5/19/10 4:29 PM Page 200

201

Fasteners

TEKS ® Fastener FeaturesHEAD

Proper head style choice will ensurestability during driving, proper clampingand desired finished appearance.

THREAD FORM AND DIAMETERThe correct choice of thread form anddiameter optimizes low installationtorque with high pullout strength.

PILOT SECTIONThe unthreaded portion of the pointassures that the drilling of the steelis completed before the threadsbegin tapping into the drilled hole.

POINTThe point is designed to efficientlyremove material and precisely sizethe hole for the thread.

Head

THREADSPILOT SECTION

(WHEN NECESSARY)

FLUTE

POINT

FINISH: Platings and coatings provide lubricity during drilling and tapping as well as corrosion resistance.

Warranty InformationProper fastener connection design takes into account where and how fasteners are used. Allowance for special characteristics in materials, differences in types of materials being joined, uniqueor unusual environmental service or installation conditions and the safety factors required by anticipating normal or short term loading conditions must be considered. Due to possible differencesin specifications, applications and interpretation of results, purchasers and specifiers must make their own evaluation of the products, to determine the suitability of these products for intendeduse. All warranties of Buildex products, expressed or implied, including the warranties of merchantability and fitness for particular purposes are specifically excluded except for the following:Buildex will repair or replace any product which, within twelve months after sale by Buildex or its distributors, is found by Buildex to be defective in material or workmanship—normal wear and tearexcepted. This is the sole warranty of Buildex and the sole remedy available to distributor or buyer. Buildex shall not be liable for any injuury, loss or damage, direct, indirect, incidental orconsequential, arising out of the use of, or the inability to use, any Buildex product.

ACQ Tested Coatings*The following fasteners have been tested with ACQ (Alkaline Copper Quaternary) treated wood: DEC-KING® Exterior wood screw withClimacoat®, Tapcon® Concrete Anchors with Blue Climaseal® and White UltraShield™, Wood-to-Metal TEKS® with Grey Spex™, Roofgrip® withSpex or Blue Climaseal and Maxi-Set Tapcon® with White UltraShield.* Due to the many test variables involved, the lack of a correlation between test results and service in the field, and the corrosive nature of ACQ treatedwood, ITW Buildex cannot guarantee the performance of any fasteners. Use of any ITW Buildex fasteners can lead to corrosion problems that may limit thelife of a structure and pose safety concerns. The decision as to the suitability of a fastener for use in treated wood is the sole responsiblity of the designprofessional of record. Should you have any questions, please feel free to call the Technical Services Department at (800) 323-0720.

Driv-Tru™ HWH Socket System

Selector Guide Part No. Description Applications1591910 Driv-Tru Socket All 1/4'' across flats HWH fasteners1513910 Driv-Tru Socket All 5/16'' across flats HWH fasteners1574910 Driv-Tru Socket All 3/8'' across flats HWH fasteners

.500

.400

.300

.200

.100

.030

.0

2.4mm

.095

.018.45mm

#10

2.4mm

.095

.018.45mm

#12

2.4mm

.095

.018.45mm

1/4

2.50mm

.100

.036.91mm

#8

5.3mm

.210

.036.91mm

#12

4.17mm

.175

.036.91mm

#10

5.3mm

.210

.036.91mm

#12

5.3mm

.210

.036

.91mm

1/4

6.36mm

.250

1253.18mm

#12

6.36mm

.250

.1253.18mm

1/4

9.51mm

.375

.1253.18mm

#12

12.72mm.500

.1253.18mm

#12

12.72mm.500

.1253.18mm

1/4

Drill and Tap Material Thickness Chart

Fastener Description and Breakdown — EXAMPLE10

–16

x3/4" HWH TEKS/3

Nominal Screw Size Threads Per Inch Screw Length Head Style Drill Point Type

Nominal Screw SizesThread Decimal

Diameter Equivalent#6 .140#7 .150#8 .160#9 .180#10 .190#11 .200#12 .210#13 .230#14 .2401/4 .250#17 .286

Steel Gauge ChartCommon

Sheet Steel Decimal Eq.Gauges Inches MM

30 .012 .3028 .015 .3826 .018 .4524 .024 .6122 .030 .7620 .036 .9118 .048 1.2116 .060 1.5214 .075 1.9012 .105 2.651/8 .125 3.1810 .134 3.42

3/16 .187 4.771/4 .250 6.361/2 .500 12.72

Mat

eria

l Th

ickn

ess

(In

ches

)

Screw SizePoint

Teks/1 Teks/2 Teks/3 Teks/4 Teks/4.5 Teks/5*Drill & tap capacities may vary with special feature designs. Refer to product reports for specifics.

201SS 5/19/10 4:29 PM Page 201

202

Fasteners

Product FeaturesSharp convex drill point has precise cuttingedges to improve drill performance with less effort.

Non-walking point provides fast materialengagement.

Unique point to thread design extrudes the metalpreventing stripout.

Point to thread design maximizes pullout performance and minimizes backout.

Four head styles available to handle variousapplications.

Climaseal® finish provides excellent corrosion resistance and lower tapping torque.

Preferred most by electrical, decking, HVAC and

metal building contractors.

TEKS ®

Self-Drilling Fasteners

Product SpecificationsDiameter . . . . . .#6, #8, #10, #12 and 1/4Thread Form . . .6-20

8-1810-16, 10-2412-141/4-14

Head Style . . . .#6: #2 Phillips Pan#8: 1/4” HWH; #2 Phillips Pan#10: 5/16'' HWH; 5/16'' HWH with Serrations; #2 Phillips Pan; #2 Phillips Oval#12: 5/16'' HWH1/4: 5/16'' HWH

Drill Point . . . . .Teks 1 Teks 2 Teks 3

Finish . . . . . . . .#6, #8, Electro-zinc#10, #12 and 1/4 Climaseal

Head StylesHex Washer Hex Oval Head

Hex Washer Head Pan Head with Serrations

Applications

Stitch roof deck and wall panel sidelaps.HVAC, electrical trim accessories to steel framing.Residential steel frame construction.

Brick ties to steel framing.Track to stud and stud splicing.Hat channel to stud.

Approvals and ListingsFactory Mutual (J.I. 2 X 9A2 AM), ICBO 3056, ICC — ESR 1976

202SS 5/19/10 4:30 PM Page 202

203

Fasteners

SelectorGuide

Head Drill Drill & Tap Max. Material Box Part No. Description Style Point Capacity Attachments Qty Applications1208200 6-20 x 3/8'' Pan #2 .036-.100 .100 20,0001210200 8-18 x 1/2'' Pan #2 .036-.100 .205 10,0001213200 8-18 x 3/4'' Pan #2 .036-.100 .455 10,0001218200 8-18 x 1'' Pan #2 .036-.100 .705 8,0001196200 8-18 x 1/2'' HWH #2 .036-.100 .205 10,0001199200 8-18 x 5/8'' HWH #2 .036-.100 .330 10,0001200200 8-18 x 3/4'' HWH #2 .036-.100 .455 10,0001202200 8-18 x 1'' HWH #2 .036-.100 .705 8,0001204200 8-18 x 1-1/2'' HWH #2 .036-.100 1.205 4,0001107000 10-16 x 3/4'' HWH #1 .018-.095 .220 5,0001109053 12-14 x 3/4'' HWH #1 .018-.095 .205 4,000 1399000 1/4-14 x 7/8'' HWH #1 .018-.095 .380 5,0001398000 10-16 x 1/2'' Pan #3 .036-.175 .150 10,0001541000 10-16 X 5/8'' Pan #3 .036-.175 .200 5,0001224000 10-16 x 3/4'' Pan #3 .036-.175 .325 5,0001542000 10-16 x 3/4'' Oval #3 .036-.175 .325 5,0001397000 10-16 x 1/2" HWH #3 .036-.175 .150 5,0001127000 10-16 x 5/8" HWH #3 .036-.175 .200 5,0001128000 10-16 x 3/4" HWH* #3 .036-.175 .325 5,000 1129000 10-16 x 1" HWH #3 .036-.175 .575 5,0001544000 10-16 x 1'' Oval #3 .036-.175 .575 5,0001545000 10-16 x 1'' Pan #3 .036-.175 .575 5,0001130000 10-16 x 1-1/4" HWH #3 .036-.175 .825 4,0001546000 10-16 x 1-1/4'' Oval #3 .036-.175 .825 5,0001131000 10-16 x 1-1/2" HWH* #3 .036-.175 1.075 3,0001550000 10-24 x 3/4'' HWH #3 .036-.175 .323 5,0001551000 10-24 x 1'' HWH #3 .036-.175 .575 5,0001786200† 10-24 x 5/8'' HWH** #2 .036-.175 .200 5,0001707200† 10-16 x 3/4'' HWH** #3 .036-.175 .323 5,000 1821200† 10-16 X 3/4'' HWH** #3 .036-.175 .323 5,000

• HVAC, electrical trim accessoriesto steel framing.

• Residential steel frameconstruction.

• Track to stud.• Hat channel to stud.• Stud splicing.

• Stitching roof deck, wall panelsidelaps or duct work.

• Clips, duct straps, brick ties oraccessories to steel framing.

• Vibration Resistance; HVAC Applications.

*Available withbonded washer.

**With serrationsunder head.

†Electro-zinc finish.

Now available in small box packaging.

A standard screwgun with a depth sensitive nosepiece shouldbe used to install Teks. For optimal fastener performance, thescrewgun should be a minimum of 4 amps and have a RPMrange of 0–2000.

Adjust the screwgun nosepiece to properly seat the fastener.

New magnetic sockets must be correctly set before use.Remove chip build-up as needed.

The fastener is fully seated when the head is flush with the work surface.

Overdriving may result in torsional failure of the fastener orstripout of the substrate.

The fastener must penetrate beyond the metal structure a minimum of 3 pitches of thread.

Installation Guidelines

Sheet Steel Gauges

The values listed are ultimate averages achieved under laboratory conditions and apply to Buildex manufactured fasteners only.Appropriate safety factors should be applied to these values for design purposes.

Gauge No. 12 14 16 18 20 22 24 26Decimal

.105'' .075'' .060'' .048'' .036'' .030'' .024'' .018''Equivalent

Fastener Tensile Shear Torque(dia-tpi) (lbs. min.) (avg. lbs. ult.) (min. in. lbs.)6-20 1285 750 258-18 1545 1000 4210-16 1936 1400 6110-24 2702 1500 6512-14 2778 2000 921/4-14 4060 2600 150

Performance Data

Fastener Steel GaugeDia. Pt. 26 24 22 20 18 16 14 12#6 2 120 183 248 296 471 679 847 —#8 2 119 193 265 298 491 703 959 —

1 148 241 311 357 565 826 1111 1796#10-16

3 124 208 266 299 499 708 967 1474#12 1 159 261 338 390 649 908 1259 1949#1/4 1 208 329 428 562 800 1151 — —

Pullout Values (average lbs. ultimate) Fastener Values

Fastener Steel Gauge (Lapped)Dia. Pt. 26 24 22 20 18 16 14#6 2 278 466 526 758 845 — —#8 2 294 496 560 740 1060 — —

1 398 584 659 884 1374 — —#10

3 — 455 526 728 1266 1540 1552#12 1 432 703 753 1018 1452 — —1/4 1 511 849 885 1244 1764 — —

Shear Values (average lbs. ultimate)

TEKS ®Self-Drilling Fasteners

203SS 5/19/10 4:30 PM Page 203

204

Fasteners


TEKS ®

Self-Drilling FastenersThe best point ever for speed and consistency ...

optimum for medium duty steel-to-steel applications.

Applications

Roof deck to steel framing.

Wall panel to girt.

Duct work to steel framing.

Accessories to steel framing

Clip to steel framing.

Retrofit framing.

Commercial overhead steel doors, hinges & latches.

Product Features

Point has precise cutting edges to improve drill performancewith less effort.

Non-walking point provides fast material engagement.

Point to thread design maximizes pullout performance andminimizes backout.

Drills and taps in the broadest range of applications.

Climaseal® finish provides excellent corrosion resistance andlower tapping torque.

Product SpecificationsDiameter . . . . . .#12, 1/4Thread Form . .12-14

1/4-14Head Style . . . .#12: 5/16'' HWH

1/4: 3/8'' HWH1/4 Overhead Door Fasteners:7/16'' HWH with Serrations

Drill Point . . . . .Teks 2Teks 3

Finish . . . . . . . .Climaseal


Head StylesHex Washer Head

Hex Washer Hex with Serrations

204SS 5/19/10 4:31 PM Page 204

205

Fasteners


SelectorGuide


A standard screwgun with a depth sensitive nosepiece shouldbe used to install Teks. For optimal fastener performance, thescrewgun should be a minimum of 6 amps and have an RPMrange of 0–2500.





The fastener must penetrate beyond the metal structure aminimum of 3 pitches of thread.

Performance Data

Head Drill Drill & Tap Max. Material Box Part No. Description Style Point Capacity Attachments Qty Applications1134000 12-14 x 3/4'' HWH #3 .036-.210 .270 5,0001136000 12-14 x 1'' HWH #3 .036-.210 .520 4,0001120000 12-14 x 1-1/4'' HWH #2 .036-.210 .550 4,0001123000 12-14 x 1-1/2'' HWH #2 .036-.210 .800 2,5001140000 12-14 x 2'' HWH #3 .036-.210 1.450 2,0001553000 12-14 X 2-1/2'' HWH #3 .036-.210 1.950 1,0001143000 12-14 x 3'' HWH #3 .036-.210 2.450 1,0001146000 12-14 x 4'' HWH #3 .036-.210 3.450 5001147000 1/4-14 x 3/4'' HWH #3 .036-.210 .210 3,0001149000 1/4-14 x 1'' HWH #3 .036-.210 .400 2,5001150000 1/4-14 x 1-1/4'' HWH #3 .036-.210 .650 2,0001152000 1/4-14 x 1-1/2'' HWH #3 .036-.210 .900 2,0001155000 1/4-14 x 2'' HWH #3 .036-.210 1.400 1,5001554000 1/4-14 x 2-1/2'' HWH #3 .036-.210 1.900 1,0001157000 1/4-14 x 3'' HWH #3 .036-.210 2.400 1,0001304000 1/4-14 x 4'' HWH #3 .036-.210 3.400 500All available with bonded washer.1586000 1/4-14 x 3/4'' *HWH #3 .036-.210 .250 3,0001587000 1/4-14 x 1'' *HWH #3 .036-.210 .500 2,500Now available in small box packaging. *With serrations under head.

• Roof deck to steel framing.

• Wall panel to girt.

• Duct work to steel framing.

• Accessories to steel framing.

• Clip to steel framing.

• Retrofit framing.

• Commercial overhead steel doors,hinges & latches.

Fastener Steel GaugeDia. Pt. 26 24 22 20 18 16 14 12 3/16

122 156 243 283 375 605 848 1181 1856 35203 142 211 289 341 551 757 1063 1631 2998

1/4 3 141 231 293 346 613 880 1145 1858 4550

Pullout Values (average lbs. ultimate)

Fastener Tensile Shear Torque(dia-tpi) (lbs. min.) (avg. lbs. ult.) (min. in. lbs.)12-14 2778 2000 921/4-14 4060 2600 150

Fastener ValuesGauge No. 12 14 16 18 20 22 24 26Decimal Equivalent

.105'' .075'' .060'' .048'' .036'' .030'' .024'' .018''

Sheet Steel Gauges

Fastener Steel Gauge (lapped)Dia. Pt. 26 24 22 20 18 16 14 12

122 365 600 623 898 1370 1758 2138 22023 — — — 769 1358 1620 1970 1986

1/4 3 — — — 930 1442 2100 2584 2650


The values listed are ultimate averages achieved under laboratory conditions and apply to Buildex manufactured fasteners only. Appropriatesafety factors should be applied to these values for design purposes.

205SS 5/19/10 4:31 PM Page 205

206

Fasteners


TEKS ®

Self-Drilling FastenersFirst in performance!! Over 30 years of consistent

drilling. The original self-drillers for heavy duty

applications.

Applications

Metal deck to structural steel or bar joist.

Clips to structural steel or bar joist.

Liner panels to structural steel or bar joist.

Accessories to structural steel or bar joist.

Longer length fasteners can be used in retrofit clip and sheetapplications.

Product Features

Unique double fluted point has precise cutting edges to improvedrill performance in 1/4'' thru 1/2'' steel.

Engineered for fast drilling and smooth tapping with less effort.


Attachments up to 7.2'' of material including 1/2'' steel.

1/4 Diameter has notched threads to reduce tapping torque.

Product SpecificationsDiameter . . . . . .#12, 1/4Thread Form . .12-24, 1/4-28Head Style . . . .#12: 5/16'' HWH

1/4: 5/16'' HWH1/4: 3/8'' HWH

Drill Point . . . . .Teks 4Teks 4.5Teks 5



Head StyleHex Washer Head

206SS 5/19/10 4:31 PM Page 206

207

Fasteners


SelectorGuide


A standard screwgun with a depth sensitive nosepiece shouldbe used to install Teks. For optimal fastener performance, thescrewgun should be a minimum of 6 amps and have an RPMrange of 0–2500. (Maximum 1800 RPM is recommended forTeks 5 fasteners)






Head Drill Drill & Tap Max. Material Box Part No. Description Style Point Capacity Attachments Qty Applications1088000 12-24 x 7/8'' HWH #4 .125-.250 .325 5,0001414000 12-24 x 1-1/4'' HWH #4.5 .125-.375 .575 4,0001006000 12-24 x 1-1/4'' HWH #5 .125-.500 .375 4,0001070000 12-24 x 1-1/2'' HWH #5 .125-.500 .625 2,5001072000 12-24 x 2'' HWH #5 .125-.500 1.125 2,0001074000 1/4-28 x 3'' HWH* #5 .125-.500 2.150 1,0001075000 1/4-28 x 4'' HWH* #5 .125-.500 3.150 5001641000 1/4-28 x 5'' HWH #5 .125-.500 4.150 2501431000 1/4-28 x 6" HWH #5 .125-.500 5.150 2501590000 1/4-28 x 8" HWH #5 .125-.500 7.150 150All available with bonded washer.Now available in small box packaging.

• Metal deck, clips, liner panels oraccessories to structural steel orbar joist.

• Longer fasteners can be used inretrofit clip and sheet applications.

* 5/16” Across Flats HWH.

Gauge No. 12 14 16 18 20 22 24 26Decimal Equivalent

.105'' .075'' .060'' .048'' .036'' .030'' .024'' .018''

Sheet Steel Gauges

Fastener Tensile Shear Torque(dia-tpi) (lbs. min.) (avg. lbs. ult.) (min. in. lbs.)

12-24 T/4 3020 2100 10012-24 T/4.5 3165 2200 15012-24 T/5 3020 2100 1501/4-28 T/5 5577 3310 234

Fastener Values

Performance Data


Shear Values (average lbs. ultimate)Fastener Steel Gauge (lapped)

Dia. Pt. 16 14 12 1/8 1/44 — — 2048 2030 —

124.5 — — 2641 2887 28975 — — 2650 2700 2762

1/4 5 1597 2005 2350 2792 3310

Fastener Steel Gauge (lapped)Dia. Pt. 16 14 12 3/16 1/4

4 — — 1532 3485 401312 4.5 — — 1508 3865 4101

5 — — 1527 3701 39991/4 5 — — 1507 3300 5059

Note: Teks fasteners are not categorized as structural bolts. Properdesign criteria and strengths must be used for satisfactoryapplication.The values listed are ultimate averages achieved underlaboratory conditions and apply to Buildex manufactured fasteners only.Appropriate safety factors should be applied to these values for designpurposes.

207SS 5/19/10 4:32 PM Page 207

208

Fasteners


TEKS ®

Low Profile Architectural Metal RoofClip Fasteners & Rake AngleShoulder TeksIncorporates the ITW exclusive Phillips Square-Driv®

anti-cam-out system.

Applications

Low profile architectural metal roof clips to steel purlin. Low profile architectural metal roof clips to wood supports.

Product Features

#12 diameter utilizes the ITW exclusive Phillips Square-Driv with patented interlocking components system.• Excellent installation stability.• Extended bit driver life.• Keeps the driver securely mated to the fastener during

installation.• Hands-free installation.

#10 Diameter uses the coated Phillips drive system providingimproved driver bit to fastener stability and friction fit.

#10 has above industry average tensile strength.

Both fasteners are finished with a corrosion resistant coating.Teks 3 fasteners are available with Gray Spex™ coating; Type A fasteners with Climacoat®.

Sharp convex drill point has precise cutting edges to improvedrill performance with less effort.

Low profile pancake head style ensures proper installation ofmetal roof panels.

Product SpecificationsLow Profile

Diameter . . . . . .#10, #12Thread Form . .10-16 (Teks 3), 10-12 (Type A)

12-14 ( Teks 3), 12-11 (Type A)Head Style . . . .#10: #2 Phillips Pancake

#12: #2 Phillips Square-Driv PancakeDrill Point . . . . .Teks® 3, Type AFinish . . . . . . . .Climacoat (Type A)

Gray Spex (Teks 3)

Rake Angle

Diameter . . . . . .1/4Thread Form . .#10, #14Head Style . . . .HWHDrill Point . . . . .#3, #4.5Finish . . . . . . . .Climaseal

#2 Phillips Square-Driv®

#2 Phillips

#2 PSD Bit

208SS 5/19/10 4:32 PM Page 208

209

Fasteners

TEKS ®Self-Drilling FastenersSelector Guide


A standard screwgun with a depth-sensitive nosepiece shouldbe used to install Teks. For optimal fastener performance, thescrewgun should be a minimum of 6 amps and have an RPMrange of 0–2500.




The fastener must penetrate a minimum of 3 pitches of threadbeyond the metal structure.

Head Drill Drill & Tap Max. Material Box Part No. Description Style Point Capacity Attachments Qty Applications1560553 10-16 x 1'' #2 Phillips Pancake #3 .036-.175 .550 4,0001575553 12-14 x 1'' #2 PSD Pancake #3 .036-.210 .550 4,0001713053 *1/4-14 x 1-1/4” HWH #3 .036-.210 .617 2,5001718053 *1/4-20 x 1-1/4” HWH #4.5 .125-.375 .440 2,5001588910 #2 PSD Bit 11596553 10-12 x 1” #2 Phillips Pancake Type A .012-.048 .250 4,0001640553 10-12 x 1-1/2'' #2 Phillips Pancake Type A .012-.048 .750 2,5001597553 12-11 x 1” #2 PSD Pancake Type A .012-.048 .250 4,000

• Low profile archi-tectural metal roof clipto steel purlin.

• For #12 Diameter Fastener• Low profile archi-

tectural metal roof clipto wood supports.

* with depth of shoulder


.105'' .075'' .060'' .048'' .036'' .030'' .024'' .018''

Sheet Steel Gauges

Fastener Tensile Shear Torque(dia-tpi) Point (lbs. min.) (avg. lbs. ult.) (min. in. lbs.)10-16 #3 1983 1400 7812-14 #3 2652 2000 9210-12 Type A 2581 1426 8112-11 Type A 3634 1994 132

Fastener Values

Performance Data


Shear Values (average lbs. ultimate)Fastener Steel Gauge (lapped)

Dia. Pt. 20 gauge 18 gauge 16 gauge 14 gauge#10 3 727 1164 1366 1460#12 3 923 1279 1657 1933

Pullout Values (average lbs. ultimate)Fastener Steel Gauge (lapped)

1/2" 5/8" 3/4" Yellow 3/4'' Dia. Pt. Plywood Plywood Plywood Pine OSB#10 Type A 364 382 400 579 288#12 Type A 377 395 427 675 326

Fastener Steel GaugeDia. Pt. 26 24 22 20 18 16 14 12#10 3 109 180 218 278 427 583 873 1406#12 3 139 194 250 369 450 598 915 1500#10 Type A 192 280 360 460 568 — — —#12 Type A 193 300 387 464 621 — — —

The values listed are ultimate averages achieved under laboratoryconditions and apply to Buildex manufactured fasteners only.Appropriate safety factors should be applied to these values for designpurposes.

209SS 5/19/10 4:33 PM Page 209

210

Fasteners


TEKS ®

Wood-to-Metal FastenersNo pre-drilling, fast, efficient attachment of wood to steel.

Applications

Plywood roof and floor sheet to steel frames.

2 x 4 headers to steel frames.

Plywood fascia to steel frames.

Wood mansard to steel frames.

Product Features


Special winged fasteners ream a hole in wood preventing thread engagement during drilling.

Wafer head design has a large bearing surface ideal forplywood.

Flat head design countersinks and seats flush in wood.

Gray Spex™ finish provides excellent corrosion resistance and lower tapping torque.

Recommended for ACQ treated wood.

Product SpecificationsDiameter . . . . . .#10, #12 and 1/4Thread Form . .10-16

10-2412-241/4-20

Head Style . . . .#10: #2 Phillips Flat; #2 PhillipsWafer; #2 Phillips Square-Driv® Flat#12: #3 Phillips Flat1/4: #3 Phillips Flat

Drill Point . . . . .Teks 3Teks 4

Finish . . . . . . . .Gray Spex

Head StylesWafer Head Flat Head

Phillips Square Driv®

210SS 5/19/10 4:33 PM Page 210

211

Fasteners

TEKS ® Wood-toMetal Self-Drilling FastenersSelector Guide

Head Drill Drill & Tap Wood Attachment Box Part No. Description Style Point Capacity Range Qty Applications1077000 10-24 x 3/4" Wafer #3 .036-.175 1/4''-3/8'' 8,0001079000 10-24 x 1" Wafer #3 .036-.175 1/4''-1/2'' 5,0001082000 10-24 x 1-7/16" *PFH #3 .060-.175 1/4''-3/4'' 3,0001791000 10-16 x 1-13/16'' **PSD Flat #3 .030-.175 1/4''-3/4'' 2,5001588910 #2 PSD Bit 11092000 12-24 x 2-1/4" *PFH #4 .125-.250 3/4''-1-3/8'' 2,0001094000 12-24 x 2-3/4" *PFH #4 .125-.250 3/4''-1-5/8'' 1,5001096000 1/4-20 x 3" *PFH #4 .125-.250 3/4''-2'' 1,000

• Plywood, mansard, fascia,roofing, flooring to steelframing.

• Plywood, 2 x 4’s headersto steel framing.

• 2 x 4’s to steel framing.




Worn or damaged bit tip should be replaced.




All #10 diameter “Winged” parts must be driven into a minimumof 16 GA steel thickness.

All 1/4 and #12 diameter “Winged” parts must be driven into aminimum of 1/8" steel in order to break the wings consistently.


.105'' .075'' .060'' .048'' .036'' .030'' .024'' .018''

Sheet Steel Gauges

Performance DataPullout Values (average lbs. ultimate)

Shear Values (average lbs. ultimate)Fastener Steel Gauge (lapped)Dia. Pt. 20 18 16 14 12 1/8#10 3 728 1266 1540 1522 — —#12 4 — — — — 2048 20301/4 4 — — — — 2650 2820

Fastener Steel GaugeDia. Pt. 26 24 22 20 18 16 14 12 3/16 1/4

#10-16 3 — 208 266 299 499 708 967 1474 — —#10-24 3 — — — 334 495 702 900 1570 3865 4101

#12 4 — — — — — — — 1508 4297 —1/4 4 — — — — — — — 1803 — —

Fastener Tensile Shear Torque(dia-tpi) (lbs. min.) (avg. lbs. ult.) (min. in. lbs.)10-16 1936 1400 6110-24 2702 1500 6512-24 3165 2200 1501/4-20 3860 2700 168

Fastener Values


*with wings **with ribs under headNow available in small box packaging.

211SS 5/19/10 4:34 PM Page 211

212

Fasteners


TEKS ®

Self-Drilling FastenersWith Bonded WasherFor weather-tight sealing of roof and wall applications.

Applications

Roof panels to purlin or bar joist. Wall panels to girt. Mansard panel to structural.

Product Features

Vulcanized bonding of washer eliminates separation of EPDMfrom the metal backing.

Dual sealing bonded washer prevents leaks.




Product SpecificationsDiameter . . . . . .#10, #12 & 1/4Thread Form . .10-16

12-1412-241/4-141/4-28

Head Style . . . .#10: 5/16'' HWH#12: 5/16'' HWH1/4 (stitch): 5/16'' HWH1/4: 3/8'' HWH

Washer Style . .Galvanized (G-90)

Drill Point . . . . .Teks 1Teks 2Teks 3Teks 4Teks 4.5Teks 5

Finish . . . . . . . .Climaseal Head Paint Available

Head StylesHex Washer Head with Bonded Washer

212SS 5/19/10 4:34 PM Page 212

213

Fasteners

TEKS ®Self-Drilling Fasteners With 9/16" Bonded WasherSelector Guide

Head Drill Drill & Tap Max. Material Box Part No. Description Style Point Capacity Attachments Qty Applications1005000 10-16 x 3/4” HWH #3 .036 - .175 .205 3,0001308000 10-16 x 1-1/2” HWH #3 .036 - .175 .955 2,5001011000 12-14 x 1” HWH #3 .036 - .210 .400 3,0001014000 12-14 x 1-1/4” HWH #2 .036 - .210 .430 2,5001404000 12-14 x 1-1/2” HWH #2 .036 - .210 .680 2,0001009000 12-14 x 3/4” HWH #3 .036 - .210 .150 3,0001016000 12-14 x 2” HWH #3 .036 - .210 1.330 1,5001333000 12-14 x 3” HWH #3 .036 - .210 2.330 1,0001332000 12-14 x 4” HWH #3 .036 - .210 3.330 5001416000 1/4-14 x 7/8” HWH #1 .018 - .095 .260 3,0001160000 1/4-14 x 1” HWH #3 .036 - .210 2,5001019000 1/4-14 x 1-1/4” HWH #3 .036 - .210 .530 2,0001020000 1/4-14 x 1-1/2” HWH #3 .036 - .210 .780 1,5001021000 1/4-14 x 2” HWH #3 .036 - .210 1.280 1,0001022000 1/4-14 x 3” HWH #3 .036 - .210 2.280 7501429000 1/4-14 x 4'' HWH #3 .036 - .210 3.280 5001010000 12-24 x 7/8” HWH #4 .125 - .250 .205 3,0001415000 12-24 x 1-1/4” HWH #4.5 .125 - .375 .455 2,5001000000 12-24 x 1-1/4” HWH #5 .125 - .500 .255 2,5001001000 12-24 x 1-1/2” HWH #5 .125 - .500 .505 2,0001002000 12-24 x 2” HWH #5 .125 - .500 1.005 1,5001003000 1/4-28 x 3” HWH #5 .125 - .500 2.030 1,0001004000 1/4-28 x 4” HWH #5 .125 - .500 3.030 5001647000 1/4-28 x 5'' HWH* #5 .125 - .500 4.030 2501642000 1/4-28 x 5'' HWH** #5 .125 - .500 4.030 2501432000 1/4-28 x 6” HWH* #5 .125 - .500 5.030 2501619000 1/4-28 x 8” HWH* #5 .125 - .500 7.030 150

• Brick tie to steelframing.

• Mansard panel to steelframing.

• Roof panel to purlin.


• Stitch roof and wallpanels.

• Retrofit panels tostructural.

• Roof and wall panel tobar joist or structural.

• Longer fasteners maybe used in retrofitapplications.* 3/4'' bonded

washer**1-1/8''

bondedwasher








.105'' .075'' .060'' .048'' .036'' .030'' .024'' .018''

Sheet Steel Gauges


Shear Values (average lbs. ultimate)Fastener Steel Gauge (lapped)Dia. Pt. 26 24 22 20 18 16 14 12 1/8 1/4#10 3 — 445 526 728 1266 1540 1552 — — —

2 365 600 623 898 1370 1758 2138 — — —#12

3 — — — 769 1358 1620 1970 1986 — —4 — — — — — — — 2048 2030 —

#124.5 — — — — — — — 2641 2887 —5 — — — — — — — 2650 2700 —1 511 849 885 1244 1764 — — — — —

#1/4 3 — — — 930 1442 2100 2584 2650 — —5 — — — — — 1597 2005 2350 2792 3310

Fastener Steel GaugeDia. Pt. 26 24 22 20 18 16 14 12 3/16 1/410 3 124 208 266 299 499 708 967 1474 — —

2 156 243 283 375 605 848 1181 1856 3520 —12

3 142 211 289 341 551 757 1063 1631 2998 —4 — — — — — — — 1532 3485 3844

124.5 — — — — — — — 1508 3865 41045 — — — — — — — 1527 3701 39991 208 329 428 562 800 1151 — — — —

1/4 3 141 231 293 346 613 880 1145 1877 4550 —5 — — — — — 607 918 1507 3300 5059

Fastener Tensile Shear Torque(dia-tpi) (lbs. min.) (avg. lbs. ult.) (min. in. lbs.)10-16 1936 1400 6112-14 2778 2000 9212-24 3020 2100 1001/4-14 4060 2600 1501/4-28 5577 3310 234

Fastener Values


Properly Seated Washers

Underdriven Correctly OverdrivenDriven

213SS 5/19/10 4:35 PM Page 213

214

Fasteners


MAXISEAL®

Integral Washer SystemMaxiseal ... The premium sealing system for Teks®

self-drilling, self-tapping fasteners.

Applications

Roof panel to purlin and wall panel to girt.

Stitching roof, wall, fascia, eave panels or gutter straps.

Roof and wall panel or accessories over blanket insulation tosteel framing.

#17 diameter replacement for stripped #12 and 1/4 diameterfasteners.

Product Features

Controls the EPDM rubber washer for improved in placeappearance and increased washer life.

Seals when driven at an angle.

Optimum pullover resistance.

Hex washer head provides excellent driving stability.






Product SpecificationsDiameter . . . . . .#10, #12, 1/4 and #17Thread Form . .10-16

12-14, 12-24

1/4-14

17-14Head Style . . . .#10: 5/16'' HWH

#12: 5/16'' HWH

1/4: 5/16'' HWH and 3/8'' HWH

#17: 5/16'' HWHWasher Style . .9/16'' O.D. Integral System

Drill Point . . . . .Teks 1Teks 2Teks 3Teks 4Teks 5Type AB

Finish . . . . . . . .Climaseal Head Paint Available

Head StylesMaxiseal Head

214SS 5/19/10 4:35 PM Page 214

215

Fasteners

MAXISEAL® Integral Washer SystemSelector Guide

Head Drill Drill & Tap Max. Material Box Part No. Description Style Point Capacity Attachments Qty Applications1376000 10-16 x 3/4” HWH #3 .036-.175 .325 3,0001023000 12-14 x 3/4” HWH #3 .036-.210 .260 3,0001659053 12-14 x 3/4” HWH #3 .012-.048 .435 2,5001026000 12-14 x 1” HWH #3 .036-.210 .490 2,5001029000 12-14 x 1-1/4” HWH #2 .036-.210 .560 2,5001428000 12-14 x 1-1/2” HWH #2 .036-.210 .790 2,0001730000 12-24 x 7/8'' HWH #4 .018-.250 .295 3,0001517000 12-24 x 1-1/2'' HWH #5 .125-.500 .500 2,5001389000 1/4-14 x 7/8” HWH #1 .018-.095 .320 3,000

1042053 1/4-14 x 3/4” HWH* #3 .036-.210 .200 2,5001044000 1/4-14 x 1” HWH* #3 .036-.210 .310 2,5001048000 1/4-14 x 1-1/2” HWH* #3 .036-.210 .810 2,0001737000 1/4-14 x 1-3/4'' HWH* #3 .036-.210 1.060 1,5001712000 1/4-14 x 3” HWH #3 .036-.210 2.310 1,0001063000 17-14 x 1” HWH AB — .685 2,500

• Roof and wall panel tosteel framing.

• Panel over insulation tosteel framing.

• Roof and wall panel tobar joist or structural.

• Stitching roof, wall,fascia, eave panels orgutter straps.

• Sheet or accessorieswith up to 6" blanketinsulation to steelframing.

• Replacement screw for12 and 1/4'' diameterfasteners.







Fastener Tensile Shear Torque(dia—tpi) (lbs. min.) (avg. lbs. ult.) (min. in. lbs.)

10-16 1936 1400 6112-14 2778 2000 92

12-24 T/4 3020 2100 10012-24 T/5 3188 2200 150

1/4-14 4060 2600 15017-14 5300 3200 180

Fastener Values





.105'' .075'' .060'' .048'' .036'' .030'' .024'' .018''

Sheet Steel Gauges


Fastener Steel GaugeDia. Pt. 26 24 22 20 18 16 14 12 3/16 1/410 3 124 208 266 299 499 708 967 1474 — —

2 156 243 283 375 605 848 1181 1856 3520 —3 142 211 289 341 551 757 1063 1631 2998 —

124 — — — — — 697 986 1532 3485 40135 — — — — — — — 1527 3701 39991 208 329 428 562 800 1151 — 1858 4550 —

1/4 3 141 231 293 346 613 880 1145 1877 4550 —AB 235 365 496 597 702 926 1180 1716 3523 —

17 AB 225 261 350 442 553 752 1122 — — —

Shear Values (average lbs. ultimate)Fastener Steel Gauge

Dia. Pt. 26 24 22 20 18 16 14 1210 3 — 445 526 728 1266 1540 1552 —

2 365 600 623 898 1370 1758 2138 —

123 — — — 769 1358 1620 1970 19864 — — — — — — — 20485 — — — — — — — 26501 511 849 885 1244 1765 — — —

1/43 — — — 930 1442 2100 2584 2650

AB 422 482 669 889 1157 — — —17 AB 459 745 989 958 1415 — — —

Now available in small box packaging. *3/8" Across Flats

215SS 5/19/10 4:36 PM 5

216

Fasteners


SCOTS ®

Long Life Teks® FastenersThe Original Buildex Scots 300 Stainless Steel Encapsulated

Head will never rust .... EVER!!!!

Applications

Panel over blanket insulation to steel frame.

Roof curb to structural steel.

Standing seam roof system endlaps.

Stitch roof and wall sidelaps.

#17 diameter replacement for stripped #12 and 1/4 diameterfasteners.

Product Features

For improved appearance and extra life an integral designcontrols the EPDM rubber washer.

Combines 300 series stainless steel exterior with the strength of carbon steel.

300 series stainless most preferred for galvalume long lifepanels.

Maximum sealing and corrosion protection.





Product SpecificationsDiameter . . . . . .#12, 1/4 and #17Thread Form . .12-14

12-24

1/4-14

1/4-28

17-14Head Style . . . .5/16'' HWH (300 Series Stainless)Washer Style . .9/16'' O.D. Integral

Drill Point . . . . .Teks 1Teks 2Teks 5Type AB

Finish . . . . . . . .Silver Climaseal Head Paint Available

Head StylesScots Head

216SS 5/19/10 4:36 PM Page 216

217

Fasteners

SCOTS® Long Life FastenersSelector Guide

Head Drill Drill & Tap Max. Material Box Part No. Description Style Point Capacity Attachments Qty Applications1165253 12-14 x 1'' HWH #3 .036-.210 .310 2,5001167253 12-14 x 1-1/4'' HWH #2 .036-.210 .560 2,5001706053 12-14 x 1-1/4" HWH (3/8" AF) #2 .036-.210 .560 2,0001168253 12-14 x 1-1/2'' HWH #2 .036-.210 .790 2,0001907053 12-14 x 1-1/2" HWH (3/8" AF) #2 .036-.210 .790 2,0001163000 12-24 x 2'' HWH #5 .125-.500 1.000 1,5001788000 1/4-28 x 4'' HWH #5 .125-.500 3.000 5001387253 1/4-14 x 7/8'' HWH #1 .018-.095 .320 2,5001175153 1/4-14 x 1-1/8'' HWH #1 .018-.095 .395 2,5001616000 1/4-14 x 1-1/4'' HWH #3 .036-.210 .630 2,000

1178253 1/4-14 x 3/4" HWH AB .012-.048 .435 2,5001180225 17-14 x 1'' HWH AB — .686 1,500

• Panel over blanketinsulation to steelframe.

• Roof curb to structuralsteel.

• Standing seam roofsystem endlaps.

• Stitch roof and wallsidelaps. SSR endlaps.

• Replacement screw for#12 and 1/4 diameterfasteners.







Fastener Tensile Shear Torque(dia-tpi) (lbs. min.) (avg. lbs. ult.) (min. in. lbs.)12-14 2778 2000 9212-24 3188 2200 1301/4-14 4060 2600 1501/4-28 5577 3310 23417-14 5300 3200 180

Fastener Values





.105'' .075'' .060'' .048'' .036'' .030'' .024'' .018''

Sheet Steel Gauges


Fastener Steel GaugeDia. Pt. 26 24 22 20 18 16 14 12 3/16 1/412 2 156 243 283 375 605 848 1181 1856 3520 —12 5 — — — — — — — 1527 3701 39991/4 5 — — — — — — — 1507 3300 5059

1 208 329 428 562 800 1151 — — — —1/4

AB 235 365 496 597 702 926 1180 1690 3446 421217 AB 225 261 350 442 553 752 1122 1716 3523 4250

Shear Values (average lbs. ultimate)Fastener Steel GaugeDia. Pt. 26 24 22 20 18 16 14 1/8 3/16 1/412 2 365 600 623 898 1370 1758 2138 2202 — —12 5 — — — — — — — 2700 2720 27621/4 5 — — — — — 1597 2005 2350 2792 3310

1 511 849 885 1244 1764 — — — — —1/4

AB 422 482 669 889 1157 — — — — —17 AB 459 745 989 958 1415 — — — — —

217SS 5/19/10 4:36 PM Page 217

218

Fasteners


410 STAINLESSSTEEL TEKS ®

Self drilling fasteners for applications requiring extra

corrosion protection

Applications

Clips to structural steel or bar joist.

Duct work to steel framing.


Brick ties to steel framing.

Accessories to structural steel or bar joist.

HVAC, electrical accessories to steel framing.

Longer length fasteners can be used in retrofit clip and sheet applications.

Product Features

Engineered for fast drilling and smooth tapping with less effort.

410 Stainless Steel for added corrosion protection.

Corrosion resistant finish for added protection compared tostandard 410 Stainless Steel products.


Product SpecificationsDiameter . . . . . .#8, #10, #12, and 1/4”Thread Form . .8-18

10-16

12-14

1/4-14Head Style . . . .#8: 5/16” HWH, #10: 5/16” HWH,

#12: 5/16” HWH, and 1/4”: 3/8” HWH

Drill Point . . . . .Teks 2, Teks 3

Head StyleHex washer head (HWH)

218SS 5/19/10 4:37 PM Page 218

219

Fasteners

410 SS TEKS® Self-Drilling FastenerSelector Guide

Head Drill Drill & Tap Max. MaterialPart No. Description Style Point Capacity Attachments Applications1897000 8-18 x 1/2" HWH #2 .036 - .100 0.2051828000 8-18 x 5/8" HWH #2 .036 - .100 0.3301829000 8-18 x 3/4" HWH #2 .036 - .100 0.4551847000 8-18 x 1-1/4" HWH #2 .036 - .100 0.9551858000 10-16 x 1/2" HWH #3 .036 - .175 0.1501830000 10-16 x 3/4" HWH #3 .036 - .175 0.3251831000 10-16 x 1" HWH #3 .036 - .175 0.5751833000 10-16 x 1-1/2" HWH #3 .036 - .175 1.0751834000 12-14 x 3/4" HWH #3 .036 - .210 0.2701835000 12-14 x 1" HWH #3 .036 - .210 0.5201836000 12-14 x 1-1/4" HWH #3 .036 - .210 0.7501837000 12-14 x 1-1/2" HWH #3 .036 - .210 0.9801838000 12-14 x 2" HWH #3 .036 - .210 1.4501839000 12-14 x 2-1/2" HWH #3 .036 - .210 1.9501840000 12-14 x 3" HWH #3 .036 - .210 2.4501842000 1/4-14 x 3/4" HWH #3 .036 - .210 0.1501843000 1/4-14 x 1" HWH #3 .036 - .210 0.4001845000 1/4-14 x 1-1/2" HWH #3 .036 - .210 0.9001893000 1/4-14 x 2" HWH #3 .036 - .210 1.400

• Metal deck, clips, lines oraccessories to structuralsteel or bar joist.

• Longer fasteners can beused in retrofit clip and sheetapplications.





The fastener is fully seated when the head is flush with the worksurface.




8-18 1545 1000 4210-16 1936 1400 6112-14 2778 2000 921/4-14 4060 2600 150

Fastener Values (average lbs. ultimate)The values listed are ultimate averages achieved under laboratoryconditions and apply to Buildex manufactured fasteners only.Appropriate safety factors should be applied to these values for designpurposes.



8 2 119 193 265 298 491 703 959 — —10 3 124 208 266 299 499 708 967 1474 —12 3 131 196 258 312 452 692 1063 1631 29981/4 3 141 231 293 346 613 880 1145 1858 4550

Pullout Values (average lbs. ultimate)Fastener Steel Gauge

Dia. Pt. 26 24 22 20 18 16 14 128 2 294 496 560 740 1060 — — —10 3 — 455 526 728 1266 1540 1552 —12 3 — — — 769 1358 1620 1970 19861/4 3 — — — 930 1442 2100 2584 2650

219SS 5/19/10 4:37 PM Page 219

220

Fasteners


410 STAINLESSSTEEL TEKS ®

Self drilling fasteners with bonded washers for applications

requiring extra corrosion protection.

Applications

Retrofit panels to steel framing.

Roof panels to purlin or bar joist.

Stitch roof and wall panels.

Wall panels to girt.

Brick ties to steel framing.

Mansard panel to structural.

Product Features






Corrosion resistant finish for added surface rust protection.

Product SpecificationsDiameter . . . . . .#10, #12, and 1/4Thread Form . .10-16

12-14

1/4-14Head Style . . . .#10: 5/16" HWH, #12: 5/16" HWH, and

1/4": 3/8" HWH

Drill Point . . . . .Teks 3

Washer Style . .9/16" O.D. Bonded

Finish . . . . . . . .Climashield®

Head StyleHex washer head withbonded washer (HWH)

220SS 5/19/10 4:38 PM Page 220

221

Fasteners

410 SS TEKS® Self-Drilling Fastener with Bonded WasherSelector Guide

Head Drill Drill & Tap Max. MaterialPart No. Description Style Point Capacity Attachments Applications1850000 10-16 x 3/4" HWH #3 .036 - .175 0.2051848000 10-16 x 1-1/2" HWH #3 .036 - .175 0.9551853000 12-14 x 1" HWH #3 .036 - .210 0.4001851000 12-14 x 1-1/4" HWH #3 .036 - .210 0.6201854000 12-14 x 1-1/2" HWH #3 .036 - .210 0.8501860000 12-14 x 2" HWH #3 .036 - .210 1.3301857000 1/4-14 x 1" HWH #3 .036 - .210 0.2801861000 1/4-14 x 1-1/4" HWH #3 .036 - .210 0.5301862000 1/4-14 x 1-1/2" HWH #3 .036 - .210 0.7801882000 1/4-14 x 2" HWH #3 .036 - .210 1.2801892000 1/4-14 x 3" HWH #3 .036 - .210 2.280

• Brick tie to steel framing.

• Mansard panel to steelframing.

• Roof panel to purlin.


• Stitch roof and wall panels.

• Retrofit panels to structural.


A standard screwgun with a depth sensitive nosepiece shouldbe used to install Teks. For optimal fastener performance, thescrew gun should be a minimum of 6 amps and have an RPMrange of 0–2500.






8-18 1545 1000 4210-16 1936 1400 6112-14 2778 2000 921/4-14 4060 2600 150

Fastener Values (average lbs. ultimate)The values listed are ultimate averages achieved under laboratoryconditions and apply to Buildex manufactured fasteners only.Appropriate safety factors should be applied to these values for design purposes.



8 2 119 193 265 298 491 703 959 — —10 3 124 208 266 299 499 708 967 1474 —12 3 131 196 258 312 452 692 1063 1631 29981/4 3 141 231 293 346 613 880 1145 1858 4550

Shear Values (average lbs. ultimate)Fastener Steel Gauge (Lapped)

Dia. Pt. 26 24 22 20 18 16 14 128 2 294 496 560 740 1060 — — —10 3 — 455 526 728 1266 1540 1552 —12 3 — — — 769 1358 1620 1970 19861/4 3 — — — 930 1442 2100 2584 2650



221SS 5/19/10 4:38 PM Page 221

222

Fasteners


304 SS & CARBONTAPPERSSelf tapping fasteners for applications requiring extra

corrosion protection.

Applications

Clips to structural or bar joist.

Longer length fasteners can be used in retrofit clip & sheet applications.

Coastal applications. (Stainless Steel Only)


Product Features


Engineered for fast and smooth tapping with less effort.

Vulcanized bonding of washer eliminates separation.

Product SpecificationsMaterial . . . . . . .304 Stainless Steel/CarbonDiameter . . . . . .#14, #17Thread Form . .14-10

17-9Head Style . . . .3/8" AF HWH

Point . . . . . . . . .Type A

Finish . . . . . . . .Carbon = Electro Zinc

Stainless = Electro Zinc

Head StyleHex head Hex head

with bonded washer with bonded washer(HWH steel) (HWH carbon)

222SS 5/19/10 4:39 PM Page 222

223

Fasteners

304 SS & CARBON TAPPERSSelector Guide

Carbon Steel 304 SeriesElectro Zinc Stainless Steel Carbon Steel 304 SS

Part No. Part No. Description Box Qty. Box Qty.1874200 1863000 14 x 3/4" HWH W/ BD Type A Tappers 2,500 2,5001875200 1864000 14 x 1" HWH W/ BD Type A Tappers 2,500 2,5001877200 1866000 14 x 1-1/2" HWH W/ BD Type A Tappers 2,000 2,0001879200 — 14 x 2" HWH W/ BD Type A Tappers 1,500 1,5001880200 — 14 x 2-1/2" HWH W/ BD Type A Tappers 1,000 1,0001881200 — 14 x 3" HWH W/ BD Type A Tappers 1,000 7501886200 — 17 x 3/4" HWH W/ BD Type A Tappers 2,500 2,0001887200 — 17 x 1" HWH W/ BD Type A Tappers — 2,000








Fastener Tensile Shear Torque(dia-tpi) (lbs. min.) (avg. lbs. ult.) (min. in. lbs.)14-10 2684 2148 12717-9 N/A N/A 229

304 SS Fastener Values (avg. lbs ultimate)

Fastener Tensile Shear Torque(dia-tpi) (lbs. min.) (avg. lbs. ult.) (min. in. lbs.)14-10 4060 2600 15017-9 5000 2750 173

Carbon Steel Fastener Values (avg. lbs ultimate)


with BondedWasher Gauge 26 24 22 20 18 16 14Fastener Thickness 0.018 0.024 0.030 0.036 0.048 0.060 0.075

14 Type ADrill Size 1/8" 5/32" 5/32" 3/16" 3/16" #7 #7

191 252 336 371 545 694 884

FastenerGauge 26 24 22 20 18 16 14

Thickness 0.018 0.024 0.030 0.036 0.048 0.060 0.075

17 Type ADrill Size 1/8" 5/32" 5/32" 3/16" #2 #2 1/4”

263 307 425 475 559 791 9

with BondedWasher Gauge 26 24 22 20 18 16 14Fastener Thickness 0.018 0.024 0.030 0.036 0.048 0.060 0.075

14 Type ADrill Size 1/8" 5/32" 5/32" 3/16" 3/16" #7 #7

595 827 1093 1341 1931 2229 2696

FastenerGauge 26 24 22 20 18 16 14

Thickness 0.018 0.024 0.030 0.036 0.048 0.060 0.075

17 Type ADrill Size 1/8" 5/32" 5/32" 3/16" #2 #2 1/4”

565 792 970 1100 1556 1813 2065


with BondedWasherFastener Gauge 26-14 24-14 22-14 20-14 18-14

14 Type ADrill Size #7 #5 #2 #2 0.234"

534 704 863 1245 2120Fastener Gauge 26-14 24-14 22-14 20-14 18-14

17 Type ADrill Size #2 1/4" 1/4" 1/4" 1/4"

454 1013 1264 1544 1294

Pullover Values (average lbs. ultimate)

223SS 5/19/10 4:39 PM Page 223

224

Fasteners


HTZ™

High Torque Zinc Die Cast Long Life

Metal Building Teks® Fasteners

Buildex HTZ fasteners exhibit the highest torsional head strength

in the zinc die cast market... no head failures.

Applications

Panel over blanket insulation to steel frame.

Stitch roof and wall sidelaps.

Standing seam roof system endlaps.

Product Features

HTZ patented “Internal Spline” provides the strongest torsionalvalues in the industry ... no head failures.

Zinc aluminum alloy head provides acceptable long liferesistance ... no red rust.

“No mar radius head design” will not scratch, pierce or damagepanels if overdriven.

Indented HWH provides excellent socket stability.

For improved appearance and extra life an integral designcontrols the EPDM washer ... maximum sealing protection.

Non-walking point, fast material engagement.

Point-to-thread design maximizes pullout performance andminimizes backout.

Product SpecificationsDiameter . . . . . .#9, #12, 1/4, #17Thread Form . .12-14, 1/4-14, 17-14, 9-15

Point Type . . . .Teks 1, Teks 2, Type AB

Finish . . . . . . . .Silver Climaseal®

Head Paint available

Head Style5/16 HWH zinc-aluminum alloy with

integral washer design.

No Mar RadiusHead Design

224SS 5/19/10 4:40 PM Page 224

225

Fasteners

HTZ High Torque Zinc Die Cast Long Life TEKS FastenersSelector Guide

Head Drill Drill & Tap Max. MaterialPart No. Description Style Point Capacity Attachments1721053 1/4-14 x 7/8" HTZ #1 .024-.095 .3201727053 12-14 x 1 HTZ #2 .024-.095 .3101725053 12-14 x 1-1/4 HTZ #2 .036-.210 .5601729053 12-14 x 1-1/2" HTZ # 2 .036-.210 .7901757053 12-14 x 2" HTZ # 2 .036-.210 1.401723053 1/4-14 x 1-1/4" HTZ # 2 .036-.210 .6301740053 1/4-14 x 3/4" HTZ AB .4351736053 1/4-14 x 1" HTZ AB .6861778053 1/4-14 x 1-1/2" HTZ AB 1.1801742053 1/4-14 x 1" HTZ AB .6851765053 9 x 1" HTZ A .012-.048 .2501767053 9 x 1-1/2" HTZ A .012-.048 .750








12-14 2778 2000 921/4-14 4060 2600 150

Fastener Values

Note: Teks fasteners are not categorized as structural bolts. Properdesign criteria and strengths must be used for satisfactory application.The values listed are ultimate averages acheived under laboratoryconditions and apply to Buildex manufactured fasteners only.Appropriate safety factors should be applied to these values for designpurposes.


.105'' .075'' .060'' .048'' .036'' .030'' .024'' .018''

Sheet Steel Gauges


Fastener Steel GaugeDia. Pt. 26 24 22 20 18 16 14 12 3/16 1/412 2 156 243 283 375 605 848 1181 1856 3520 —

1 208 329 428 562 800 1151 — — — —1/4 2 141 231 293 346 613 830 1145 1858 4550 —

AB 235 365 496 597 702 926 1180 1690 3446 4212

Shear Values (average lbs. ultimate)Fastener Steel Gauge

Dia. Pt. 26 24 22 20 18 16 14 1212 2 365 600 623 898 1370 1758 2138 2202

1 511 849 885 1244 1764 — — —1/4 2 — — — 930 1442 2100 2584 2650

AB 422 482 669 889 1157 — — —

225SS 5/19/10 4:40 PM Page 225

226

Fasteners


TEKS ®

Exterior Rigid InsulationFastenersThe original self-drilling fasteners designed specifically

for rigid insulation.

Applications

Roof and wall panel over rigid insulation to steel framing. Roof panel over spacer block and insulation to eave purlin.

Product Features

Unique rider section stops panel jacking, point burnout and breakage.

High thread under the head prevents panel stripout.

Improved in place aesthetics.

Available in Scots® and Maxiseal® headstyles.

Maximum pullover performance.

Excellent driving stability.

Seals when driven at an angle.

Fastens the broadest range of insulation thickness.





Product SpecificationsDiameter . . . . . .#12Thread Form . .12-14 with rider sectionHead Style . . . .5/16'' HWH Maxiseal

5/16'' HWH Scots 300 SeriesStainless

Washer Style . .9/16'' O.D. Integral System

Drill Point . . . . .Teks 3


Head paint available

Head StyleMaxiseal Head Scots Head

226SS 5/19/10 4:41 PM Page 226

227

Fasteners

TEKS® Exterior Rigid Insulation FastenersSelector Guide

Head Drill Drill & Tap Insulation BoxPart No. Description Style Point Capacity Range Qty ApplicationsMaxiseal®1034000 12-14 x 1-7/8" HWH #3 .036-.210 3/4" to 1" 1,5001036000 12-14 x 2-3/8" HWH #3 .036-.210 1-1/8" to 1-1/2" 1,0001038000 12-14 x 3-1/4" HWH #3 .036-.210 1-5/8" to 2-3/8" 7501040000 12-14 x 4" HWH #3 .036-.210 2-1/8" to 3" 500Scots®

1169200 12-14 x 1-7/8" HWH #3 .036-.210 3/4" to 1" 1,5001170200 12-14 x 2-3/8" HWH #3 .036-.210 1-1/8" to 1-1/2" 1,0001171200 12-14 x 3-1/4" HWH #3 .036-.210 1-5/8" to 2-3/8" 7501172200 12-14 x 4" HWH #3 .036-.210 2-1/8" to 3" 500

• Roof and wall panel overrigid insulation to steelframing.

• Roof panel over spacerblock and insulation to eavepurlin.







Fastener Tensile Shear Torque(dia-tpi) (lbs. min.) (avg. lbs. ult.) (min. in. lbs.)12-14 2778 2000 90

Fastener Values



Fastener Steel GaugeDia. Pt. 26 24 22 20 18 16 14 12 3/1612 3 142 211 289 341 551 757 1063 1631 2998

Shear Values (average lbs. ultimate)Fastener Steel Gauge (Lapped)

Dia. Pt. 26 24 22 20 18 16 14 1212 3 — — — 769 1358 1620 1970 1986




.105'' .075'' .060'' .048'' .036'' .030'' .024'' .018''

Sheet Steel Gauges

227SS 5/19/10 4:41 PM Page 227

228

Fasteners

TRUGRIP GT ™

Metal-to-Wood Fasteners

The preferred fastener by the leading post frame builders

and manufacturers.

Applications

Roof and wall panel to wood structure.

Panel over insulation to wood structure.

Stitch roof and wall panel.

Product Features

Non-walking sharp gimlet point for fast material engagement.

Double lead thread for fast panel pick-up.



High hat HWH for driving stability.


Product SpecificationsDiameter . . . . . .#9 and #12Thread Form . .9-15 double lead

12-14Head Style . . . .1/4" HWHWasher Style . .Galvanized (G-90)Drill Point . . . . .GimletFinish . . . . . . . .Climaseal

Head Paint Available

Head StyleHex Washer Head

Hex Washer Head with Bonded Washer

228SS 5/19/10 4:42 PM Page 228

229

Fasteners

TRUGRIP™ GT Metal-to-Wood FastenersSelector Guide

MaterialHead Drill Drill & Tap Attachment Box

Part No. Description Style Point Capacity Range Qty Applications1271000 9-15 x 1'' HWH Gimlet .012-.048 0-.250 7,0001272000 9-15 x 1-1/2'' HWH Gimlet .012-.048 0-.750 4,0001275000 9-15 x 2-1/2'' HWH Gimlet .012-.048 1.000-1.750 1,5001276000 9-15 x 3'' HWH Gimlet .012-.048 1.500-2.250 1,5001558000 14-10 x 1-1/2" 5/16" AF HWH Type 17 .012-.048 .445 3,0001277000 12-14 x 3/4'' HWH Gimlet .012-.048 — 4,000With 1/2'' Bonded Washer1262000r 9-15 x 1'' HWH Gimlet .012-.048 0-.250 4,0001264000r 9-15 x 1-1/2'' HWH Gimlet .012-.048 0-.750 2,5001267000 9-15 x 2'' HWH Gimlet .012-.048 .500-1.250 2,0001268000 9-15 x 2-1/2'' HWH Gimlet .012-.048 1.000-1.750 1,5001269000 9-15 x 3'' HWH Gimlet .012-.048 1.500-2.250 1,0001525053 14-10 x 1” 3/8” AF HWH Type 17 .012-.048 0-.445 2,5001526053 14-10 x 1-1/2" 5/16" AF HWH Type 17 .012-.048 0-.750 2,0001270000 12-14 x 3/4'' *HWH Gimlet .012-.048 — 4,000

• Wall panel to woodstructure

• Panel over insulation towood.

• Stitching of wall panel.

• Roof and wall panel towood.

• Panel over insulation towood.

• Stitching of roof andwall panel.








9-15 1800 1200 5012-14 2778 2000 92

Gauge Decimal No. Equivalent18 .048''20 .036''22 .030''24 .024''26 .018''28 .015''30 .012''

Fastener Values Sheet Steel Gauges



Performance DataPullout Values in Steel(average lbs. ultimate)

Fastener Steel GaugeDia. 26 24 22 20 18

9 171 252 329 401 63412 199 271 360 426 656



9 Unwashered 465 623 815 1049 15499 Washered 515 674 875 1100 1627

12 Unwashered 527 699 863 912 118512 Washered 587 744 915 993 1246

Fastener Embedment in 2'' x 4''Dia. 1/2" 3/4" 1" 1-1/4" 1-1/2"

9 198 328 571 728 87212 210 335 — — —

Pullout Values in Wood(average lbs. ultimate)

*With 9/16'' O.D. Bonded Washer.

The values listed are ultimate averagesachieved under laboratory conditions andapply to Buildex manufactured fastenersonly. Appropriate safety factors should beapplied to these values for designpurposes.

229SS 5/19/10 4:42 PM Page 229

230

Fasteners

SCOTS ®

TRUGRIP ™

Long Life Post Frame Fasteners

Applications

Roof and wall panel to wood structure.

Panel over insulation to wood structure.

Stitch roof and wall panel.

Product Features

Integral washer head design seals even when driven at an angle.

300 series stainless head most preferred for galvalume long lifepanels.

#10 Hi-Lo thread has 30% greater pullout than #9 in wood.

Climaseal long life finish resists corrosive elements in wood.

Type 17 point for fast cutting and easier tapping.

Product SpecificationsDiameter . . . . . .#10 and #12Thread Form . .10-16 Hi-Lo and 12-14 Double Lead

Scots HeadHead Style . . . .1/4'' Across Flats HWH

(300 Series Stainless)Washer Style . .7/16'' O.D. Integral Head with EPDM WasherDrill Point . . . . .#10: Type 17

#12: GimletFinish . . . . . . . .Climaseal® long life finish

Head Style

230SS 5/19/10 4:43 PM Page 230

231

Fasteners

SCOTS® TRUGRIP™ Long Life Post Frame FastenersSelector Guide

MaterialHead Drill Drill & Tap Attachment Box

Part No. Description Style Point Capacity Range Qty Applications1951000 10-16 x 1'' HWH Type 17 .012-.048 0-.250 2,5001953000 10-16 x 1-1/2'' HWH Type 17 .012-.048 0-.750 2,5001955000 10-16 x 2'' HWH Type 17 .012-.048 .500-1.250 1,0001957000 10-16 x 2-1/2'' HWH Type 17 .012-.048 1.000-1.750 1,0001691053 12-14 x 3/4'' HWH Gimlet .012-.048 — 4,000

• Roof and wall panel towood structure.

• Panel over insulation towood structure.

• Stitching of roof andwall panel.








9 1800 1200 5010 1927 1200 7112 2778 2000 92

Gauge Decimal No. Equivalent18 .048''20 .036''22 .030''24 .024''26 .018''28 .015''30 .012''

Fastener Values Sheet Steel Gauges



Performance DataPullout Values in Steel(average lbs. ultimate)


9 171 252 329 401 63410 151 238 291 359 47812 199 271 360 426 656



9 Washered 515 674 875 1100 162710 Washered 548 932 1122 1444 189412 Washered 587 744 915 993 —

Fastener Embedment in 2" x 4" (SYP)Dia. 1/2" 3/4" 1" 1-1/4" 1-1/2"

9 198 328 571 728 87210 256 710 753 1121 135812 210 335 — — —

Pullout Values in Wood(average lbs. ultimate)

The values listed are ultimate averages achieved under laboratory conditions and apply to Buildex manufactured fasteners only. Appropriate safety factorsshould be applied to these values for design purposes.

231SS 5/19/10 4:43 PM Page 231

232

Fasteners

Expandable Edged Flashing

Product Features

20 year warranty

Wraps around almost any profile

Paintable after installation

TPE has a continuous service temperature range of -58°F to +240°F

Serpentine edges stretch up to 25% for added length

Great for large round pipes

Handles vibration & expansion

Applications

Large square & round ducts & penetrations

Chimneys

Skylights

Parapet Flashing

Expansion Joints

Stepped Roof

Dissimilar roof profiles

Transition wall

Gambrel roof

Flash between dissimilar materials

Product SpecificationsMaterial . . . . . . . . . . .Grey TPEBase Kit Contents

• Dekstrip material• 1" x 4' Aluminum termination strip• 3" x 2' Splice tape

Selector GuideBase Kit Fasteners NeededPart No. Description Weight (1-1/2" o.c.)4157910 7" x 75' 26 lb. 12004155910 9" x 75' 31 lb. 12004156910 12" x 75' 38 lb. 12004171910 18" x 50' 30 lb. 800

Accessories for Dekstrip Part No. Description Used On1175100 1/4-14 x 1-1/8" Scots® T/1 Metal roof and wall3358407 1/4 x 1-3/4" Scots Tapcon Concrete/masonry4172910 .040 x 1" x 4' Aluminum Termination Strip Terminating/joining ends of Dekstrip4040910 Sikaflex 201 Polyurethane Sealant Sealing edges on all surfaces4178910 3" x 2' Splice tape Splicing, lapping, sealing to all surfaces3379910 Condrive® 500 Tool Basic (2) Piece Tapcon® installation tool3103910 Condrive® 1000 Tool (2) Piece Tapcon® installation tool3119910 Condrive® 2000 Tool (1) Piece Tapcon® installation tool

DEKSTRIP™

Expandable Edged Flashing

Stretches to any shape, seals & stays.

232SS 5/19/10 4:44 PM Page 232

233

Fasteners

DEKSTRIP™ Expandable Edge Flashing


Basic Installation

1. Snap a chalk line to providea guide for applying sealant.

2. Apply a continuous bead ofsealant along chalk line.

3. Position top edge of Dekstripover seal bead and installBuildex fasteners at 1-1/2"maximum intervals on topedge. Repeat steps 1, 2,and 3 for the bottom edge.

Splicing

1. Apply splice tape toDekstrip.

Materials Needed:• Leather Gloves • 3" x 2' splice tape• Heat Gun • Shears or scissors

Detailed Instructions1. Cut splice tape (supplied in Dekstrip carton) to

the width needed and remove clear film fromone side of the tape. Lining up the edges, pressthe tape firmly onto the Dekstrip to remove airpockets.

2. Remove remaining film from tape. Apply secondpiece of Dekstrip over tape and press firmly.

3. Apply heat over spliced area for 1–2 minuteswhile applying firm pressure over entire splicedarea to ensure adhesion.

4. Turn material over and repeat step 3.

2. Position second Dekstripover tape & press in place.

3. Apply heat and pressfirmly to seal edges.

Joining ends around round pipes

1. Cut splice tape tolength, removefilm from one sideand apply toDekstrip.

2. Remove film fromtop of splice tape.

3. Overlap top pieceof Dekstrip andpress onto tape.

4. Fold terminationstrip in half, cut towidth, and slideover spliced area.

5. Fasten throughtop of terminationstrip, Dekstrip,and back of stripwith Scotsfasteners or rivets.

6. Apply sealant toall seams.

4. Apply additional sealant toboth fastened edges formaximum weather-tightsealing.

233SS 5/19/10 4:44 PM Page 233

234

Fasteners

DEKTITE SQUARE™

DEKTITE EZi-SEAL™Pipe FlashingsThe Original Flexible Pipe Flashing System Now With a Square Base and Square with Pre-AppliedSealing Gasket

ApplicationsPlumbing, Heating, Air Conditioning, Electrical and Exhaust Vents.

Product FeaturesDektite Square

Excellent property retention in temperature extremes(continuous range of -65°F to 250°F).

Made of long life, flexible, weatherproof black EPDM rubber.

Flexible, corrosion resistant aluminum base conforms to anypanel configuration.

EPDM will not crack or break.

Pipe diameter markings are clearly indicated for accurate fitting.

Designed for 1/4" to 17-3/8" diameter pipes.

One piece construction is easy to install.

Proven resistance to ozone and ultra-violet light.

Ideal for steep slope (up to 45°) roofs.

Dektite RZi-Seal

Same features and benefits of Dektite Square with these addedbenefits:

Base gasket eliminates the need for additional chemical sealers.

Watertight seal achieved at 40% compression of gasket.

Seals on wet or dry surfaces.

Product SpecificationsPipe Diameter Ranges . . .1/4'' to 17-3/8" Materials . . . . . . . . . . . . . . .Black EPDM

Dektite Installation Guidelines

STEP 1: Cut Dektite® atappropriate pipediameter marking.

STEP 2: SlideDektite flashingdown over pipe.

STEP 3: Press Dektite®

base into contours ofpanel configurations.(Apply sealant to squareDektite underside)

STEP 4: FastenDektite® to surfacewith Buildex SCOTS®

self-drilling fasteners.(Apply sealant aroundsquare Dektite Base)

STEP 5: Use theseDektite® products onthe ‘diamond’ or biasfor enlarged holesand penetrations onsteep pitched roofsup to 45° or deepcorrugations.

Notes: • Dekite can be installed over or between the ribs of standard panels.• DO NOT install over SSR or architectural panel ribs.• Generally no sealant is required where the Dektite collar provides a compression fit around the pipe.

However, some metal pipes and flues include a seam which may require a local application of silicone sealantat the point where the Dektite collar crosses the seam.

234SS 5/19/10 4:45 PM Page 234

235

Fasteners

DEKTITE SQUARE™ & EZi-SEAL™ Pipe Flashings Selector Guide

Pipe Outside Dektite BasePart No. Description Diameter Dimensions4159910 Mini SQ 0"–1-3/8" 3-7/8" x 3-7/8"4147910 Mini EZ 0"–1-3/8" 3-7/8" x 3-7/8"4160910 #1 SQ 1/4"–2-1/8" 5-3/8" x 5-3/8"4148910 #1 EZ 1/4"–2-1/8" 5-3/8" x 5-3/8"4161910 #2 SQ 2"–2-3/4" 7" x 7"4149910 #2 EZ 2"–2-3/4" 7" x 7"4162910 #3 SQ 2"–4-3/4" 8-9/16" x 8-9/16"4150910 #3 EZ 2"–4-3/4" 8-9/16" x 8-9/16"4163910 #5 SQ 4-1/2"–6-1/4" 11-3/16" x 11-3/16"4151910 #5 EZ 4-1/2"–6-1/4" 11-3/16" x 11-3/16"4194910 #7 SQ 6-1/4"–8-3/4" 14-3/8" x 14-3/8"4152910 #7 EZ 6-1/4"–8-3/4" 14-3/8" x 14-3/8"4195910 #8 SQ 8-3/4"–11-3/4" 17-7/8" x 17-7/8"4153910 #8 EZ 8-3/4"–11-3/4" 17-7/8" x 17-7/8"4196910 #9 SQ 11-1/2" x 17-3/8" 22-7/8" x 22-7/8"4154910 #9 EZ 11-1/2" x 17-3/8" 22-7/8" x 22-7/8"

ASTM TestMethod Test Description Specification Results

D412 Tensile Strength 1450 1537(min. psi rating) psi min. psi

D412 Ultimate Elongation (%) 350 min. 535D1171 Resistance to Ozone— 100 Passed

min. rating (no cracks)D673 Heat Aging—70 hrs.

at 212° F Change in Hardness (points) +15 max. +8Change in Tensile Strength (%) ±30 max. -4.7Change in elongation (%) ±50 max. -26

Note: When used on roofs where pitch is steeper than 20 degrees, or when used ondeep ribbed profile roof panel (1-1/2" deep corrugation or more), consider using nextlarger size Dektite that will accommodate the same pipe diameter. RecommendedFastener: 1/4-14 x 1-1/8" Scots® Teks®/1, Part No. 1175153.

Performance DataASTM Test

Method Test Description Specification Results D2137 Low Temperature Non-brittle Passed

Brittleness—3 mins.at -40° F

D624 Tear Resistance Die C 125 pounds 130(min.) per inch per inch poundsof width min. of width

U.L. 94 Flame Resistance U.L. 94 PassedH.B.

Star Sales

We stock a complete line of

Power Tool Accessories

235SS 5/19/10 4:45 PM Page 235

236

Fasteners

DEKTITE ® andRETROFIT DEKTITE ®

Pipe Flashings

The original flexible pipe flashing system with a

20 year warranty.

Applications

Plumbing, Heating, Air Conditioning, Electrical and Exhaust Vents.

Product Features

Made of long life, flexible, weatherproof gray EPDM rubber orred silicone.

Flexible, corrosion resistant aluminum base conforms to anypanel configuration.

EPDM and silicone will not crack or break.

Pipe diameter markings are clearly indicated for accurate fitting.

Designed for 1/4'' to 18'' diameter pipes.

One piece construction is easy to install.

Pleated cone adjusts to any roof pitch and allows for completeflexibility.

EPDM has a continuous service temperature range of -65°F to+250°F.

Silicone has a continuous service temperature range of -40°F to+350°F

Proven resistance to ozone and ultra-violet light.

Product SpecificationsPipe Diameter Ranges . . .1/4'' to 18''—Dektite

3/4'' to 10''—Retrofit Dektite1/4'' to 18''—Silicone

Product SpecificationsMaterials . . . . . . . . . . . . . . .EPDM—Standard and Retrofit

Silicone—High Temperature

Dektite Installation Guidelines

STEP 1: Cut Dektiteat appropriate pipediameter marking.

STEP 2: SlideDektite flashingdown over pipe.

STEP 3: Applysealant on under-side of flexiblealuminum base.

STEP 4: PressDektite base intocontours of panelconfiguration.

STEP 5: FastenDektite to surfacewith Buildex SCOTSself-drilling fasteners.Apply additionalsealant around baseif desired.

Notes: • Dekite can be installed over or between the ribs of standard panels.• DO NOT install over SSR or architectural panel ribs.• Generally no sealant is required where the Dektite collar provides a compression fit around the pipe.

However, some metal pipes and flues include a seam which may require a local application of sealant at thepoint where the Dektite collar crosses the seam.

236SS 5/19/10 4:45 PM Page 236

237

Fasteners

Dektite ® & Retrofit Dektite ® Pipe Flashings Selector Guide

Pipe DektiteOutside Base Dektite Box

Part No. Description Diameter Dimensions Height Qty4001910 Mini 1/4"-1-1/8" 3-1/2" 1-3/4" 204003910 1 1/4"-2" 4-3/4" 3" 104004910 2 1-3/4"-3-1/4'' 6-1/4" 4" 104009910 3

1/4"-5" 7-3/4" 4" 104035910 #3 Silicone4011910 4 3"-6" 9-1/4" 5" 104016910 5

4"-7" 10-3/4" 5" 54036910 #5 Silicone4018910 6 5"-9" 12-1/2" 6" 54020910 7 6"-11" 14-1/2" 6" 54025910 8

7"-13" 16-1/2" 6" 54038910 #8 Silicone4028910 9

10"-18" 25-3/8" 8" 24039910 #9 Silicone

Dektite Pipe DektiteSize Outside Base Dektite Box

Part No. No. Diameter Diameter Height Qty4029910 801 3/4''-2-3/4'' 6-3/10'' 3-1/2'' 104030910 802 2''-7-1/4'' 10-3/4'' 5-3/5'' 54031910 803 3-1/4''-10'' 14-1/2'' 5-4/5'' 5

ASTM TestMethod Test Description Specification Results D412 Tensile Strength 1450 1537

(min. psi rating) psi min. psiD412 Ultimate Elongation (%) 350 min. 535D1171 Resistance to Ozone— 100 Passed


at 212° F Change in Hardness (points) +15 max. +8Change in Tensile Strength (%) ±30 max. -4.7Change in elongation (%) ±50 max. -26

Note: When used on roofs where pitch is steeper than 20 degrees, or when used on deep ribbed profile roof panel (1-1/2'' deep corrugation ormore), consider using next larger size Dektite that will accommodate the same pipe diameter. Recommended Sealant: Chemseco Sikaflex®

sealant, part number 4040910. Recommended Fastener: 1/4-14 x 1-1/8'' Scots® Teks®/1, Part No. 1175153.

Performance Data

Retrofit Dektite Installation Guidelines

ASTM TestMethod Test Description Specification Results D2137 Low Temperature Non-brittle Passed


D624 Tear Resistance Die C 125 pounds 130(min.) per inch per inch poundsof width min. of width

U.L. 94 Flame Resistance U.L. 94 PassedH.B.

Standard Dektite Retrofit Dektite

Dektite Flashing Guide

Retrofit Dektite Selector Guide

STEP 1: Begincutting opposite ofthe mechanicallocking joiner. Cutthrough the joinerwith tin snips.

Recommended Sealant: Chemseco Sikaflex® sealant, Part No. 4040910.

STEP 2: WrapRetrofit Dektitearound the pipe.Engage the topsection of the joinerfirst, then proceeddown until joiner iscompletely engaged.

STEP 3: Crimp joinertightly, starting at thetop by squeezingjoiner “fingers” withpliers.

STEP 4: Applysealant to theunderside of theribbed aluminumbase. Press RetrofitDektite againstcontours of the panelconfiguration.

STEP 5: AttachRetrofit Dektite to thepanel with SCOTS®

self-drilling screws.Screws should bespaced as necessaryto avoid gapsbetween the baseand the panel.

STEP 6: Applyadditional sealantaround the top of theDektite, near themechanical lockingjoiner seam.

237SS 5/19/10 4:46 PM Page 237

238

Fasteners

DEK-CAP™

Standing Seam Roof End Cap Flashing

The only universal end cap flashing!!

Applications

Product Features

Universal design allows use on left and right handed seams.

Flexible, corrosion resistant aluminum base conforms to themajority of standing seam roof panels.

Pre-formed panel profile shape is designed to reduce installation time.

Fastening locations are clearly indicated for accurate installation.

Dual underside ridges provide maximum sealing protection.

Thermal elastomer material provides excellent resistance toozone, ultra-violet light and extreme temperatures.

Thermal elastomer has a continuous service temperature rangeof -40°F to 250°F.

Expansion notch provides added installation flexibility.

Interior panel stop ensures correct installation position.

Product SpecificationsMaterial . . . . . . .Thermal Elastomer

Width . . . . . . . .7-1/4''

Length . . . . . . . .5-3/4''

Height . . . . . . . .3-5/16''

Color . . . . . . . . .Gray

238SS 5/19/10 4:46 PM Page 238

239

Fasteners

DEK-CAP™ Standing seam roof end cap flashingSelector Guide

Part No. Description Applications Box Quantity4146910 Dek-Cap Metal Curbs, Skylights, 10

Ridge Applications,Jobsite Retrofit

ASTM TestMethod Test Description Specification Results D412 Tensile Strength 1450 1500

(min. psi rating) psi min. psiD412 Ultimate Elongation (%) 350 min. 450D1171 Resistance to Ozone— 100 Passed


at 212° F • Change in Hardness

(points) ±15 max. +3• Change in Tensile

Strength (%) ±30 max. +2• Change in

elongation (%) ±50 max. -3

Performance Data


ASTM TestMethod Test Description Specification Results D2137 Low Temperature Non-brittle Passed


D624 Tear Resistance 125 pounds Die C (min.) per inch Passed

of width min.

STEP 1: Bend top sothat both sides areparallel to metal roof.

Recommended Sealant: Chemseco Sikaflex® sealant, Part No. 4040910.

STEP 2: Press Dek-Cap edges intocontours of panelconfiguration.

STEP 3: Removeand apply sealant onunderside of flexiblealuminum edging.

STEP 4: Slide Dek-Cap flashing overpanel profile.

STEP 5: Followindicated fasteningpattern to attach Dek-Cap to surface withBuildex Scots self-drilling fasteners.

STEP 6: Applyadditional sealantaround base ifdesired.

239SS 5/19/10 4:47 PM Page 239

240

Fasteners

TAPCON ®

The Original Masonry Fastening System

The original masonry anchor

that cuts threads into

concrete, brick or hollow block.

Approvals and Listings Miami Dade County ICC–ES City of Los Angeles

Product Control Approved ESR–1671 RR25644

Product Features

Fast installation ... drill a hole ... drive an anchor.

Packaged with one Tapcon “close tolerance” masonry drill bitper 100 anchors. Also available in bulk packaging.

Available in 3/16'' diameter up to 4'' in length and 1/4'' diameterup to 6'' in length.

Recommended for use in ACQ treated wood.

Replaces small diameter expansion anchors, plugs and screwsin light to medium duty applications.

No need to pre-spot holes ... and no inserts are required.

Reversible and removable ... can be installed close to an edge.

Installation Tools

Condrive 500®—Compact high speed installation tool designedfor installation of Tapcon hex head and Phillips flat headanchors up to 3-3/4'' long.

Condrive 1000®—A multi-purpose tool designed for installationof Tapcon hex head and Phillips flat head anchors up to 3-3/4''long.

Buildex Condrive Tools are designed to specifically installTapcon Anchors and to fit standard hammer drills.

Applications

Electrical junction boxes and conduit clips to masonry.

Wood headers and furring strips to masonry.

HVAC strapping to masonry.

Plywood backer boards to masonry.

Exterior insulation systems to masonry.

Product SpecificationsDiameter . . . . . .3/16" & 1/4"Thread Form . . .Original Notched Hi-Lo®

Point Type . . . .NailFinish . . . . . . . .Blue Climaseal®

Head Styles3/16'' Diameter: 1/4'' slotted hex washer head (HWH)1/4'' Diameter: 5/16'' slotted hex washer head (HWH)

3/16'' Diameter: #2 phillips flat head (PFH)1/4'' Diameter: #3 phillips flat head (PFH)

NEWDESIGN!

AdvancedThreadformTechnology™Easier toinstall—less torquerequired!

240SS 5/19/10 4:47 PM Page 240

241

Fasteners

The Original Tapcon Masonry Fastening System®

Selector GuidePart No. Fixture

PFH HWH Description Drill Bit Part No. Thickness Common Applications3169407 3139407 3/16 x 1-1/4" 5/32 x 3-1/2" 3095910 0–1/4"3183407 3153407 1/4 x 1-1/4" 3/16 x 3-1/2" 3098910 0–1/4"3171407 3141407 3/16 x 1-3/4" 5/32 x 3-1/2" 3095910 1/–3/4"3185407 3155407 1/4 x 1-3/4" 3/16 x 3-1/2" 3098910 1/4–3/4"

3173407 3143407 3/16 x 2-1/4" 5/32 x 4-1/2" 3096910 3/4"–1-1/4"3187407 3157407 1/4 x 2-1/4" 3/16 x 4-1/2" 3099910 3/4"–1-1/4"3175407 3145407 3/16 x 2-3/4" 5/32 x 4-1/2" 3096910 1-1/4"–1-3/4"3189407 3159407 1/4 x 2-3/4" 3/16 x 4-1/2" 3099910 1-1/4"–1-3/4"3177407 3147407 3/16 x 3-1/4" 5/32 x 5-1/2" 3097910 1-3/4"–2-1/4"3191407 3161407 1/4 x 3-1/4" 3/16 x 5-1/2" 3100910 1-3/4"–2-1/4"3179407 3149407 3/16 x 3-3/4" 5/32 x 5-1/2" 3097910 2-1/4"–2-3/4"3193407 3163407 1/4 x 3-3/4" 3/16 x 5-1/2" 3100910 2-1/4"–2-3/4"3181407 3151407 3/16 x 4" 5/32 x 5-1/2" 3097910 2-1/2"–3"3195407 3165407 1/4 x 4" 3/16 x 5-1/2" 3100910 2-1/2"–3"3197407 3167407 1/4 x 5" 3/16 x 6-1/2" 3102910 3-1/4"–4"3203407 3205407 1/4 x 6" 3/16 x 7-1/2" 3206910 4-1/4"–5"3379910 Condrive 500® For 3/16 and 1/4 diameter, Hex and Flat Heads, lengths up to 3-3/4"3103910 Condrive 1000® For 3/16 and 1/4 diameter, Hex and Flat Heads, lengths up to 3-3/4”

The minimum embedment requirement is 1" and the maximum embedment is 1-3/4".One drill bit is provided with every box of 100 pieces.*SDS with Hex Drill Bits: 5/32" x 7" SDS Rotary Hammer Drill Bit, Part No. 3311910;(*Condrive 1000 Only) 3/16" x 7" SDS Rotary Hammer Drill Bit, Part No. 3101910.

• Mounting brackets; control panels; cable clamps,conduit clips, junction switch and control boxes.

• 1/2'' or 3/4'' plywood backer boards; mountingbrackets; control panels; cable clamps; conduitclips, junction, switch and control box meters.

• 1 x 2 wood furring; 3/4'' plywood backer boards;metal safety grating.

• 2 x 4 wood nailers

• Sill plates; 2 pieces of 2 x 4 or 2 x 6 to masonry.Insulation to masonry.

Anchor Embedment Concrete StrengthDiameter Depth 2000 psi 4000 psi 5000 psi

1" 600 650 8003/16" 1-1/2" 1090 1090 1220

1-3/4" 1450 1460 17301" 750 800 950

1/4" 1-1/2" 1380 1820 21701-3/4" 2020 2380 2770

CONDRIVE 500 GUIDELINES:STEP 1: Place drill adapter into 3/8'' or 1/2'' chuck of standard hammer drill. Place drill bit in

drill adapter and tighten set screw. Drill hole a minimum of 1/4'' deeper than Tapconanchor is to be embedded.

STEP 2: Phillips Heads may be installed using either side of sleeve. To install a 1/4 diameterHex Washer Head Tapcon, use large opening side of sleeve (see sleeve label). Toinstall a 3/16 diameter Hex Washer Head Tapcon, use small opening side of sleeve(see sleeve label). Slide opposite side of sleeve over drill bit and snap onto drill bitadapter. NOTE: If driving Hex Washer Head Tapcon, driver will automaticallydisengage. If driving Phillips Head Tapcon, care must be taken to ensure anchor isnot overdriven.

STEP 3: Loosen set screw on side of drill adapter with 1/8'' Hex Key. Do not removecompletely. Replace old drill bit with new one. Align flat side with set screw andtighten screw. Do not overtighten.

CONDRIVE 1000 GUIDELINES:STEP 1: Place correct drill bit into driver adapter and drill hole 1/4" deeper than depth of

embedment.STEP 2: Slide Condrive Installation Tool sleeve over drill bit. Snap hex head or

Phillips Socket in place.STEP 3: Insert anchor in socket, position fixture to be fastened, begin to drive Tapcon

into pre-drilled hole.STEP 4: The anchor is fully set when the nosepiece of the Condrive Tool automatically

disengages from the socket and fixture is secured in place.

Note: Indicated tension and shear failure values were obtained in tests conducted at CELConsulting. Designated holding power depends on the quality of the masonry material, depth ofembedment and proper hole size. These figures are offered only as a guide and are notguaranteed in any way by Illinois Tool Works Inc. The figures indicate average ultimate tensionand shear failure values. A safety factor of 4:1 or 25% of ultimate value is generally accepted as asafe working load. However, reference should always be made to applicable codes for the specificsafe working ratio. All values are based on close tolerance holes drilled with Buildex Tapcon®

carbide drill bits. Performance of the Tapcon anchor may vary in extremely hard concreteaggregates. Consult your Buildex representative for further information.

As in the case with all applications, Buildex can only suggest typical fasteners for typicalapplications and that the connection design is the sole responsibility of the Building DesignEngineer, Architect or otherwise responsible person charged with the design of the connection.For further product information, please contact the nearest Authorized Buildex Distributor or theBuildex Technical Service Department at 1-800-323-0720.

Tapcon Anchors must be installed using allBuildex system components (TapconAnchors, Condrive Tools and Tapcon DrillBits) in order to qualify for ITW Buildexsystem support.

Performance Data Installation Guidelines:Tension in Normal-weight Concrete (lbs.)


1" 720 720 8603/16" 1-1/2” 860 860 860

1-3/4" 870 990 9901" 900 1360 1440

1/4" 1-1/2" 1200 1380 16701-3/4" 1670 1670 1670

Shear in Normal-weight Concrete (lbs.)

Tension (lbs.) Shear (lbs.)Anchor Light Medium Light Medium

Diameter Weight Weight Weight Weight3/16" 220 340 400 7301/4" 250 500 620 1000

Tension and Shear in CMU (1" Embedment)

For minimum edge distance and spacing distance, please refer toICC-ES report or Miami-Dade report for this product. Lightweight and medium-weight Concrete Masonry Units (CMU) were defined by ASTM C 90.

241SS 5/19/10 4:47 PM Page 241

242

Fasteners

MAXI-SET TAPCON ®

Masonry Fastening System

For Tapcon applications that require more anchor

bearing surface.



Product Features

Same reliable performance and speed of installation as regularTapcon.

Large 5/8" diameter flange provides more bearing surface andincreases pullover resistance. High 5/16" hex head adds drivingstability.

Compatible with DrivTru™ socket system. Improves installation.Protects paint finish. See below.

UltraShield™ and White UltraShield™ long-life finish deliverexcellent corrosion resistance.

Optional Bronze painted head over White UltraShield to matchcommon aluminum extrusions.

Packaged in bulk. Masonry drill bits sold separately.

Applications

Shutters—protective and decorative.

Screened porch and pool enclosures.

Various sheet metal flashings.

Decorative wrought iron.

Wood nailers and plywood attachment.

Product SpecificationsDiameter . . . . . .1/4"Thread Form . . .Advanced Threadform

Technology®

Point Type . . . .NailFinish . . . . . . . .UltraShield or White

UltraShield

Head Styles5/16" across flats hex with 5/8" diameter flange.

Installation SocketDrivTru™ 5/16" HWH Socket System.Part No. 1513910.For specifications, see Product Report Number 01213.

NEWDESIGN!


242SS 5/19/10 4:48 PM Page 242

243

Fasteners

MAXI-SET TAPCON® Masonry Fastening SystemSelector Guide

Anchor Anchor Box/Ctn Drill Bit Anchor Description Part No. Qty/Qty Drill Bit Part No. Finish

1/4 x 1-3/4" 3294000 1,000 3/16 x 3-1/2" 3098910 UltraShield1/4 x 2-1/4" 3295000 1,000 3/16 x 4-1/2" 3099910 UltraShield1/4 x 1-3/4" 3383100* 1,000 3/16 x 3-1/2" 3098910 White UltraShield1/4 x 2-1/4" 3384100* 1,000 3/16 x 4-1/2" 3099910 White UltraShield1/4 x 2-3/4" 3408100* 1,000 3/16 x 4-1/2" 3099910 White UltraShield1/4 x 3-1/4" 3409100* 750 3/16 x 5-1/2" 3100910 White UltraShield

Carbide Drill Bits Bit Standard(Straight Shank) Part No. Tube Qty.

3/16 x 5-1/2'' 3100910 10 pcs.3/16 x 6-1/2'' 3102910 10 pcs.3/16 x 7-1/2'' 3206910 10 pcs.

Item Part No. Qty/BoxCondrive 500® 3379910 10

Condrive 1000® 3103910 5

Carbide Drill Bits Bit Standard(SDS Shank) Part No. Tube Qty.

3/16 x 7'' 3101910 1 piece

Optional Items: Original Tapcon Carbide Drill Bits, Condrive Tools and Installation Sockets.

NOTE: Must use a DrivTru™ Socket (Part No. 1513910) when usinga Condrive Tool.


1" 750 800 9501/4" 1-1/2" 1380 1820 2170

1-3/4" 2020 2380 2770

Note: Indicated tension and shear failure values were obtained in tests conducted at CELConsulting. Designated holding power depends on the quality of the masonry material, depth ofembedment and proper hole size. These figures are offered only as a guide and are notguaranteed in any way by Illinois Tool Works Inc. The figures indicate average ultimate tensionand shear failure values. A safety factor of 4:1 or 25% of ultimate value is generally accepted as asafe working load. However, reference should always be made to applicable codes for the specificsafe working ratio. All values are based on close tolerance holes drilled with Buildex Tapcon®carbide drill bits. Performance of the Tapcon anchor may vary in extremely hard concreteaggregates. Consult your Buildex representative for further information.


Performance DataTension in Normal-weight Concrete (lbs.)


1" 900 1360 14401/4" 1-1/2" 1200 1380 1670

1-3/4" 1670 1670 1670



Diameter Weight Weight Weight Weight1/4" 250 500 620 1000


For minimum edge distance and spacing distance, please refer to ICC-ESreport or Miami-Dade report for this product. Lightweight and medium-weight Concrete Masonry Units (CMU) were defined by ASTM C 90.

*Available with Bronze painted head over White UltraShield™.Note: 2-3/4'' and 3-1/4'' lengths are special orders. Contact customer service for leadtimes.

243SS 5/19/10 4:48 PM Page 243

244

Fasteners

SCOTS TAPCON ®

Premium concrete anchor that combines the

corrosion protection of stainless steel with the

holding power of our regular carbon steel Tapcon.



Product Features

300 Series Stainless Steel Head.

Pullout strength of carbon steel.

Integral washer design provides more bearing surface.

Rubber EPDM sealing washer “locks-out” moisture from building interior.

Head paint available in white or bronze (extra charge).

Provides the same strong holding power as regular and Maxi-Set Tapcon.

Reduces job call-backs to replace “weathered” fasteners.

Applications

Shutters—Protective and Decorative.

Screened—Porch and Pool Enclosures.

Aluminum Fixtures.

Railings.

Metal Roofing.

Flexible Flashings.

Product SpecificationsDiameter . . . . . .1/4"Thread Form . . .Advanced Threadform

Technology®

Point Type . . . .NailFinish . . . . . . . .Silver Climaseal®

Head Style . . . .5/16'' HWH (300 SeriesStainless)

Head Styles

Installation SocketDrivTru™ 5/16" HWH Socket System.Part No. 1513910.For specifications, see Product Report Number 01213.

NEWDESIGN!


244SS 5/19/10 4:49 PM Page 244

245

Fasteners

SCOTS TAPCON ® Exterior Concrete AnchorSelector Guide

Anchor Anchor Box/Ctn Drill Bit Anchor HeadDescription Part No. Qty/Qty Drill Bit Part No. Finish Paint

1/4 x 1-3/4" 3358407 100 / 1,000 3/16" x 3-1/2" 3098910 Silver Climaseal® White or Long-Life Bronze

1/4 x 2-1/4" 3359407 100 / 1,000 3/16" x 4-1/2" 3099910 Coating Call for Quote

Carbide Drill Bits Bit Standard(Straight Shank) Part No. Tube Qty.

3/16 x 5-1/2'' 3100910 10 pcs.3/16 x 6-1/2'' 3102910 10 pcs.3/16 x 7-1/2'' 3206910 10 pcs.

Item Part No. Qty/BoxCondrive 500® 3379910 10Condrive 1000® 3103910 5

Carbide Drill Bits Bit Standard(SDS Shank) Part No. Tube Qty.

3/16 x 7'' 3101910 1 piece

Optional Items: Original Tapcon Carbide Drill Bits, Condrive Tools and Installation Sockets.

NOTE: Must use a DrivTru™ Socket (Part No. 1513910) when usinga Condrive Tool.


1" 750 800 9501/4" 1-1/2" 1380 1820 2170

1-3/4" 2020 2380 2770

Note: Indicated tension and shear failure values were obtained in tests conducted at CELConsulting. Designated holding power depends on the quality of the masonry material, depth ofembedment and proper hole size. These figures are offered only as a guide and are notguaranteed in any way by Illinois Tool Works Inc. The figures indicate average ultimate tensionand shear failure values. A safety factor of 4:1 or 25% of ultimate value is generally accepted as asafe working load. However, reference should always be made to applicable codes for the specificsafe working ratio. All values are based on close tolerance holes drilled with Buildex Tapcon®

carbide drill bits. Performance of the Tapcon anchor may vary in extremely hard concreteaggregates. Consult your Buildex representative for further information.


Performance DataTension in Normal-weight Concrete (lbs.)


1" 900 1360 14401/4" 1-1/2" 1200 1380 1670

1-3/4" 1670 1670 1670



Diameter Weight Weight Weight Weight1/4" 250 500 620 1000


For minimum edge distance and spacing distance, please refer to ICC-ESreport or Miami-Dade report for this product. Lightweight and medium-weight Concrete Masonry Units (CMU) were defined by ASTM C 90.

Daily deliveries throughoutNew England via our trucks

or common carrier.

245SS 5/19/10 4:49 PM Page 245

246

Fasteners

410 STAINLESS

STEEL TAPCON ®

Masonry Fastening System

Premium masonry anchor that provides the corrosion

protection of 410 Stainless Steel and the performance

of our original carbon Tapcon.

Approvals and Listings (Miami-Dade covers 1/4" Dia. only)

Miami Dade County ICC–ES

Product Control Approved ESR–1671

Product Features


Fast installation ... drill a hole ... drive an anchor.

Cuts threads into concrete, brick and hollow block.

Available in 3/16" and 1/4" diameters in lengths 1-1/4''– 3-3/4"for 3/16" diameter and now, up to 6" for 1/4" diameter HWH’s.

Buildex head marking for easy field identification

Reversible and removable ... can be installed close to an edge.

Optional white or bronze head paint to match commonaluminum extrusions.

100 count packaging.

Applications

Shutters—protective and decorative

Windows

Screened porch and pool enclosures

Railings—safety and decorative

Marine

Agricultural

New Longer

Lengths —

4", 5", and 6"!

Product SpecificationsDiameter . . . . . .3/16" & 1/4"Thread Form . . .Original Notched Hi-Lo®

Point Type . . . .NailMaterial . . . . . .410 Stainless SteelFinish . . . . . . . .ClimaShield™

Head Styles1/4" Diameter: 5/16" slotted hex washer head (HWH)

3/16'' Diameter: #2 phillips flat head (PFH)1/4'' Diameter: #3 phillips flat head (PFH)

4

4

BX

BX

246SS 5/19/10 4:50 PM Page 246

247

Fasteners

410 SS TAPCON® Corrosive Environment Masonry Fastening System Selector Guide

Part No. Drill Bit Fixture3/16" Diameter Description Part No. Drill Bit Thickness Common Applications

PFH 3434907 3/16 x 1-1/4" 3095910 5/32 x 3-1/2" 0–1/4"3418907 3/16 x 1-3/4" 3095910 5/32 x 3-1/2" 1/4–3/4"

3419907 3/16 x 2-1/4" 3096910 5/32 x 4-1/2" 3/4–1-1/4"3420907 3/16 x 2-3/4" 3096910 5/32 x 4-1/2" 1-1/4"–1-3/4"3421907 3/16 x 3-1/4" 3097910 5/32 x 5-1/2" 1-3/4x2-1/4"3422907 3/16 x 3-3/4" 3097910 5/32 x 5-1/2" 2-1/4x2-3/4"

1/4" DiameterPFH HWH

3373907 3367907 1/4 x 1-1/4" 3098910 3/16 x 3-1/2" 0–1/4"3374907 3368907 1/4 x 1-3/4" 3098910 3/16 x 3-1/2" 1/4–3/4"

3375907 3369907 1/4 x 2-1/4" 3099910 3/16 x 4-1/2" 3/4–1-1/4"3376907 3370907 1/4 x 2-3/4" 3099910 3/16 x 4-1/2" 1-1/4"–1-3/4"3377907 3371907 1/4 x 3-1/4" 3100910 3/16 x 5-1/2" 1-3/4"–2-1/4"3378907 3372907 1/4 x 3-3/4" 3100910 3/16 x 5-1/2" 2-1/4–2-3/4"

3459907 1/4 x 4" 3100910 3/16 x 5-1/2" 2-1/2"–3"3460997 1/4 x 5" 3102910 3/16 x 6-1/2" 3-1/4"–4"3461907 1/4 x 6" 3206910 3/16 x 7-1/2" 4-1/4"–5"

3379910 3379910 Condrive 500® For hex and flat heads lengths up to 3-3/4''.3103910 3103910 Condrive 1000® For hex and flat heads lengths up to 3-3/4''.

Depth of Embedment Anchor in Solid Material (inches)

Diameter 1" 1-1/4" 1-1/2" 1-3/4"3/16" 964 1080 1360 15951/4" 1381 1616 2041 2332

Performance DataPullout (lbs.) in Concrete (3000 PSI, cured 40 days)

Depth of Embedment Anchor in Solid Material (inches)

Diameter 1-1/4"3/16" 5401/4" 754

Pullout in Hollow Block

Shear Strength Shear StrengthAnchor Anchor 3145 PSI Hard Lightweight

Diameter Embedment Rock Concrete Hollow Block3/16" 1-1/4" 1460 10961/4" 1-1/4" 1622 1218

Shear Strength

Tapcon Anchors must be installed using all Buildex system components (Tapcon Anchors, Condrive Toolsand Tapcon Drill Bits) in order to qualify for ITW Buildexsystem support.

• Mounting brackets and control panels.• 1/2'' or 3/4'' plywood backer boards;

mounting brackets; control panels; cableclamps; conduit clips; junction, switch andcontrol box meters.

Metal safety gratings, 2 x 4 wood nailers.Sills, plates 2 pieces of 2x4 or 2x6 tomasonry. Insulation to masonry.• Marine and agricultural.

• Mounting brackets and control panels.• 1/2'' or 3/4'' plywood backer boards;

mounting brackets; control panels; cableclamps; conduit clips; junction, switch andcontrol box meters.

• Metal safety gratings, 2 x 4 wood nailers.• Sills, plates 2 pieces of 2x4 or 2x6 to

masonry.Insulation to masonry.• Marine and agricultural.• Maximum attachment applications

(i.e., wood/insulation/masonry)

CONDRIVE 500® GUIDELINES:STEP 1: Place drill adapter into 3/8'' or 1/2'' chuck of standard hammer drill. Place drill bit in

drill adapter and tighten set screw. Drill hole a minimum of 1/4'' deeper than Tapconanchor is to be embedded.

STEP 2: Phillips Heads may be installed using either side of sleeve. To install a 1/4 diameterHex Washer Head Tapcon, use large opening side of sleeve (see sleeve label). Toinstall a 3/16 diameter Hex Washer Head Tapcon, use small opening side of sleeve(see sleeve label). Slide opposite side of sleeve over drill bit and snap onto drill bitadapter. NOTE: If driving Hex Washer Head Tapcon, driver will automaticallydisengage. If driving Phillips Head Tapcon, care must be taken to ensure anchor isnot overdriven.

STEP 3: Loosen set screw on side of drill adapter with 1/8'' Hex Key. Do not removecompletely. Replace old drill bit with new one. Align flat side with set screw andtighten screw. Do not overtighten.

CONDRIVE 1000® GUIDELINES:STEP 1: Place correct drill bit into driver adapter and drill hole 1/4" deeper than depth of

embedment.STEP 2: Slide Condrive Installation Tool sleeve over drill bit. Snap hex head or

Phillips Socket in place.STEP 3: Insert anchor in socket, position fixture to be fastened, begin to drive Tapcon

into pre-drilled hole.STEP 4: The anchor is fully set when the nosepiece of the Condrive Tool automatically

disengages from the socket and fixture is secured in place.

Installation Guidelines:

Note: Designated holding power depends on the quality of the masonry material, depth of embedment and proper hole size. These figures are offered only as a guide andare not guaranteed in any way by Illinois Tool Works Inc. The figures indicate average ultimate tension and shear failure values. A safety factor of 4:1 or 25% of ultimatevalue is generally accepted as a safe working load. However, reference should always be made to applicable codes for the specific safe working ratio. All values are basedon close tolerance holes drilled with Buildex Tapcon® carbide drill bits. Performance of the Tapcon anchor may vary in extremely hard concrete aggregates. Consult yourBuildex representative for further information.

As in the case with all applications, Buildex can only suggest typical fasteners for typical applications and that the connection design is the sole responsibility of the BuildingDesign Engineer, Architect or otherwise responsible person charged with the design of the connection. For further product information, please contact the nearest AuthorizedBuildex Distributor or the Buildex Technical Service Department at 1-800-323-0720.

Tapcon Anchors must be installed using all Buildex system components (Tapcon Anchors, Condrive Tools, and Tapcon Drill Bits) in order to qualify for ITW Buildex system support.

247SS 5/19/10 4:50 PM Page 247

248

Fasteners

Simple solutions for hurricane protection needs with brand

names you know you can trust.

Applications

Direct mount permanent anchors for quick and easy installations for metal and plywood panels to wood, hollow block, and concrete.

Approvals and ListingsMiami Dade County

Product Control Approved

Product Features

Threaded chamfered safety collar prevents overdriving.

Available in UltraShield™ or white UltraShield™ for superioranticorrosion resistance in coastal environments.

Available in 2-1/4" and 3-1/4" lengths.

Both lengths have 1/4-20 x 7/8" external thread above collar.

3/16" Hex Drive.

No caulking required.

Product SpecificationsDiameter . . . . . .1/4"Point Type . . . .NailFinish . . . . . . . .UltraShield or White UltraShield

Direct Mount

Storm Panel

Anchors!

248SS 5/19/10 4:50 PM Page 248

249

Fasteners

TAPCON ® SG Hurricane ProtectionSelector Guide

Part No. Description* Coating Box Qty.3424000 1/4" dia. x 2-1/4" UltraShield 10003424100 1/4" dia. x 2-1/4" White UltraShield 10003425000 1/4" dia. x 3-1/4" UltraShield 5003425100 1/4" dia. x 3-1/4" White UltraShield 5003426910 3/16" Nut Driver — 13098910 3/16" x 3-1/2" Masonry Drill Bit — 1

Embedment EdgeSubstrate Depth Distance Test Value

1" 1.25" Tension 1230 lbs.1" 2.50" Tension 1701 lbs.

Concrete 1.75" 1.25" Tension 2704 lbs.3295 PSI 1.75" 2.50" Tension 2844 lbs.

1" 1.25" Shear 1339 lbs.1" 2.50" Shear 2333 lbs.1.75" 1.25" Shear 1375 lbs.1.75" 2.50" Shear 2618 lbs.1.25" 1.25" Tension 1955 lbs.

Hollow Block 1.25" 2.50" Tension 1940 lbs.1500 PSI 1.25" 1.25" Shear 536 lbs.

1.25" 2.50" Shear 1088 lbs.Grout Filled 1.75" 1.25" Tension 3335 lbs.

CMU 1.75" 2.50" Tension 3779 lbs.2000 PSU 1.75" 1.25" Shear 1207 lbs.

1.75" 2.50" Shear 2061 lbs.1" .75" Tension 2779 lbs.

Wood SYP 1.50" .75" Tension 3589 lbs.053 S.G. 1.50" 2" Shear 1750 lbs.

1.50" .75" Shear 841 lbs.1" .75" Shear 609 lbs.

Performance Data

*Length below safety collar.

Our personnel are trained to be

knowledgeable and courteous.

Visit our website: www.starsales.com

249SS 5/19/10 4:51 PM Page 249

250

Fasteners

SAMMYS brings its internal thread system to the

hurricane protection market.

Applications

Low profile permanent anchors for quick and easy secure shutter installations.

Approvals and ListingsMiami Dade County

Product Control Approved

Product Features

1/4-20 internal thread.

Cap made of 304 stainless steel will never rust.

“Original” Tapcon® 1/4 dia. anchor with blue Climaseal™ forconcrete installations up to 6" in length.

Wood fasteners available in 2" and 3" lengths in 410 stainless steel.

Torx® driver for fast and easy installations.

Product SpecificationsTapcon Anchor

Diameter . . . . . .1/4"Point Type . . . .NailFinish . . . . . . . .Blue Climaseal

Wood FastenersDiameter . . . . . .3/16"Point Type . . . .GimletFinish . . . . . . . .410 Stainless Steel

Low Profile

Storm Panel

Anchors!

Hurricane ShutterFasteners

250SS 5/19/10 4:51 PM Page 250

251

Fasteners

Hurricane ProtectionSelector Guide

Part No. Anchor Length Box Qty.8103957 1-1/4" 1258169957 1-3/4" 1258164957 2-1/4" 1258165957 2-3/4" 1258167957 3-1/4" 1258166957 3-3/4" 1258162957 4" 1258168957 5" 1258155957 6" 1258182910 Installation Tool 1

Part No. Anchor Length Box Qty.8104957 2" 1258105957 3" 1258170910 Installation Tool 1

Embedment EdgeSubstrate Depth Distance Test Value

1" 1.25" Tension 1533 lbs.1" 2.50" Tension 2024 lbs.2.25" 1.25" Tension 2972 lbs.

Concrete 2.25" 2.50" Tension 3099 lbs.3295 PSI 1" 1.25" Shear 1166 lbs.

1" 2.50" Shear 1264 lbs.2.25" 1.25" Shear 1342 lbs.2.25" 2.50" Shear 1906 lbs.1.25" 1.25" Tension 1388 lbs.

Hollow Block 1.25" 2.50" Tension 1427 lbs.1500 PSI 1.25" 1.25" Shear 526 lbs.

1.25" 2.50" Shear 1056 lbs.

Grout Filled2.50" 1.25" Tension 3011 lbs.

CMU2.50" 2.50" Tension 3332 lbs.

2000 PSU2.25" 1.25" Shear 1086 lbs.2.25" 2.50" Shear 1317 lbs.1" .75" Tension 1885 lbs.

Wood SYP 1.50" .75" Tension 2484 lbs..53 S.G. 1.50" 2" Shear 1598 lbs.

1.50" .75" Shear 1018 lbs.1" .75" Shear 1010 lbs.

Performance Data

Sammys SSC for Concrete Sammys SSW for Wood

410 StainlessSteel

“Original”Tapcon

1/4 x 20InternalThread

304 StainlessSteel

Wood(SSW)

Concrete &Hollow Block

(SSC)

Do you have atapping or threading problem?

Let us help you.

251SS 5/19/10 4:51 PM Page 251

252

Fasteners

E-Z PRODUCTS

Self-Drilling Drywall AnchorsThe Original! Fast and easy self-drilling anchors.

E-Z Zinc™, E-Z Stud Solver™, E-Z Mini™, E-Z Lite™,

E-Z Plastic Plus™, Twist-N-Lock™, and E-Z Toggle™

Product Features

No hole preparation necessary; pre-drills own small precise holein gypsum wallboard.

Replaces plastic plugs and toggles.

Deep thread design provides strong engagement in 3/8'', 1/2''and 5/8'' gypsum wallboard.

Installs quickly and easily with a phillips screwdriver or squaredrive bit.

Full range of anchors to cover all wall fastening applications.

Applications

Electrical Fixtures

Thermostats

HVAC Fixtures

Plumbing Fixtures

Bathroom Accessories

Shelving and Supports

Mirrors

Picture Frames

Brackets

Plaques and Awards

Closet Organizers

Coat Racks

Curtain Rods

Signs

Bulletin Boards

Control Systems

Decorative Wall Hangings

Office Material Holders

Smoke Detectors

Clocks

Kitchen Accessories

Doorbells

Telecommunications Equipment

Chalk Boards

Remote Control Boxes

Available in corrosion resistant, non-conductive white nylon.

Can be easily backed-out.

Low profile head.

Single point designs for clean cutting installation.

Stud Solver—attachments through gypsum and wood! Works in double drywall applications, too!

— #8 diameter 1-1/4" screws included— Bulk packaging only

Product SpecificationsProduct Material . . . . . .Zinc die cast, Carbon, Steel, NylonDrilling Capacity . . . . .3/8'', 1/2'' and 5/8'' gypsum wallboard

Twist-N-Lock™

holds up to 75 lbs.

in 1/2" Drywall!

252SS 5/21/10 9:19 AM Page 252

253

Fasteners

E-Z PRODUCTS Self-Drilling Drywall AnchorsSelector Guide


Performance Data

Anchor Anchor Part Quantity Maximum Fixture Accommodates SheetDescription Material Number Thickness Metal Screw Size

White Nylon5006902 10–100 ct boxes 3/4'' #65006900 Bulk—10,000 Anchors

Zinc5033902 10–100 ct boxes 3/4'' #6, #7, or #85033900 Bulk—3,000 Anchors

Zinc5052900 Bulk Only - 3/4'' Use only #8 with

1,500 Anchors & Screws screw provided

Zinc5000902 10–100 ct boxes 3/4'' #6, #7, or #8

Bulk—1,500 Anchors

White Nylon5035902 10–100 ct boxes 3/4'' #6, #7, or #85035900 Bulk—4,500 Anchors

White Nylon5061900 10–200 ct boxes with 2 bits 3/4''5061902 Bulk—4,500 Anchors

5014901 50 ct–50 #8 x 2-1/8'' Pan SMS 1/2" #8

Zinc5014900 Bulk—500 Anchors & Screws

5017901 50 ct—50 #8 x 2-1/8''5017900 Large Washer Face SMS

Bulk—500 Anchors & Screws

Pullout Values (ultimate average lbs.)Gypsum Thickness

3/8'' 1/2'' 5/8''Light Duty Plastic 25 30 40Light Duty Zinc 30 40 50Medium Duty 40 50 75Twist-N-LockHeavy Duty 70 85 150

1. Place #2 Phillips screwdriver into recess of E-ZZinc, E-Z Lite, E-Z Mini, E-Z Stud Solver or E- ZPlastic Plus.

2. Press into drywall while turning the anchorclockwise until it is seated flush with wall.

3. Place fixture in position over installed E-Z Zinc, E-Z Lite, E-Z Mini , E-Z Stud Solver, or PlasticPlus. Insert screw with screw driver. Tightenfixture in place.

These performance values are averagesobtained under laboratory conditions.Note that these values will changedepending on age, moisture content andsurface treatment of the drywall (gypsum)material. Appropriate safety factorsshould be applied to these values fordesign purposes.

Ligh

t Dut

y

E-Z

Min

iE

-Z L

ite

Hea

vy D

uty

E-Z

Tog

gle

Med

ium

Dut

y

Twis

t-N

-Lo

ckE

-ZP

last

icP

lus

E-Z

Zin

c

Light Duty & Medium Duty E-Z Ancors

1. Using a #2 Phillips screwdriver, drill the E-ZToggle Anchor into drywall until the head of theanchor is seated flush.

2. To “set” the clamp behind the drywall, place themounting screw into the anchor and push or tapfirmly until approximately 1” of screw is protruding(do not rotate). Then remove the screw.

3. Place fixture over E-Z Toggle, insert screw andcontinue to turn until fastened tightly (for examplewhen attaching a 1/2" thick fixture, it will requireapprox. 23 full rotations of the screwdriver to fullytighten the fixture).

Heavy Duty E-Z Toggle

253SS 5/19/10 4:53 PM Page 253

254

Fasteners

Product FeaturesRock-On

Rib design under head countersink into dense material whilepreventing stripouts.

Two point types for steel and wood applications.

Larger head diameter increases board surface contact forgreater pullover resistance.

Rock-On is recommended for ACQ treated wood.

Applications

Backer-On

Gimlet points starts easily—no predrilling.

Serrated thread design provides reduced installation torque andsuperior holding power.

Rib design under head countersinks into dense material whilepreventing stripouts.

#2 square drive prevents bit from slipping.

Product SpecificationsRock-OnDiameter . . . . . . . . . . . .#8; #9Thread Form . . . . . . . . .8-18; 9-15 Hi-Lo®

Drill Point . . . . . . . . . . .#8 Type S-12®; #9 Type “S”Head Style . . . . . . . . . .Wafer Head with countersinking ribsFinish . . . . . . . . . . . . . .Climacoat®

Rock-OnDiameter . . . . . . . . . . . .#10Thread Form . . . . . . . . .10-10 SerratedDrill Point . . . . . . . . . . .GimletHead Style . . . . . . . . . .Wafer Head with countersinking ribsFinish . . . . . . . . . . . . . .Long life epoxy topcoat/zinc plating.

ROCK-ON™

Cement Board FastenersHigh performance rib design is still the best!!!

BACKER-ON™

Fiber Cement BackboardFastenersRecognized for use with HARDIBACKER®

fiber cement backerboard.

Cement-type boards orany dense sheathingsto steel or wood studs.

Wire lath to steel orwood studs.

Plywood to steel orwood studs.

Hardie Fiber CementBackerboard

254SS 5/19/10 4:53 PM Page 254

255

Fasteners

Cement Board FastenersSelector Guide

26 24 22 20 18 16 14 12S-12 120 191 239 285 470 663 910 1424Hi-Lo 163 242 314 370 — — — —

Backer-On 271 371 457 615 — — — —

1/2'' 3/4'' 1'' 1-1/4''Hi-Lo 223 312 555 676

Backer-On — 436 780 —

Performance DataPullout Values in Steel (Gauge)

Wood (Embedment)#2 SPF 2 X 4

Gauge No. 12 14 16 18 20 22 24 26Decimal

Equivalent.105'' .075'' .060'' .048'' .036'' .030'' .024'' .018''

Sheet Steel Gauges




Worn or damaged bit tips should be replaced.




Part MaterialNumber Length Attachment Range ApplicationsHi-Lo Rock-On2151500* 9 x 1-1/4'' Up to 3/4'' Material Thickness to Wood;

3/8''–1'' Material Thickness to Steel2153500* 9 x 1-5/8'' Up to 1-1/8'' Material Thickness to Wood;

3/8''–1-3/8'' Material Thickness to Steel2155500 9 x 2-1/4'' Up to 1-3/4'' Material Thickness to Wood;

1'' to 1-7/8'' Material Thickness to SteelS-12 Rock-On2156500* 8 x 1-1/4'' 3/8'' to 3/4'' Material Thickness2159500* 8 x 1-5/8'' 3/8'' to 1-1/4'' Material Thickness2139500 8 x 2-1/4'' 1'' to 1-7/8'' Material ThicknessBacker-On2406000 10 x 1-1/4'' Up to 3/4'' Material Thickness to Wood;

3/8''–1'' Material Thickness to Steel

• Cement Board to Wood or Light GaugeSteel 26-20 Gauge

• Cement Board to Steel Studs 20-12 Gauge

• Backer Board

*Fully Threaded.Available in small box packaging.

The values listed are ultimate averages achieved under laboratoryconditions and apply to Buildex manufactured fasteners only. Appropriatesafety factors should be applied to these values for design purposes.

255SS 5/19/10 4:54 PM Page 255

256

Fasteners


DEC-KING ®

Exterior Wood Screws

Product Features

Coated with Climacoat® for maximum resistance to corrosion,staining and streaking inside the lumber and on the deck.

Recommended for ACQ treated wood.

Pullout strength is superior over nails.

Eliminates wood splitting, nail pops, hammer marks and bent nails.

Available in both #2 Phillips & #2 Square Drive.

Dec-U-Drive™ Stand-Up Installation ToolSeats Dec-King screws flush with the deck without damaging the wood.

Eliminates angle driving, underdriven or overdriven screws, screw wobble, camouts and marring of the deck surface.

Increases productivity and improves the quality of work; providing significant labor and installed cost savings.

Stand-up operation reduces operator fatigue and increases productivity.

B

XBX

256SS 5/19/10 4:54 PM Page 256

257

Fasteners

DEC-KING ® Exterior Wood Screws Selector Guide

Description 1/2'' 3/4'' 1'' 1-1/4''6 x 1-1/4" 182 329 422 —6 x 1-5/8'' 182 329 422 6207 x 2'' 189 318 440 6308 x 2-1/2'' 186 290 502 6308 x 3'' 186 290 502 64510 x 3-1/2'' 241 386 522 721

Performance DataPullout Values (average pounds ultimate) Embedment 2'' x 4'' Stud Grade S.Y. Pine

Note: The values listed are ultimate averages achieved under laboratory conditions. An appropriate safety factorshould be applied in these values to achieve a design value.

Part No.Description #2 Square Drive #2 Phillips Applications6 x1-1/4'' — 2176500 1'' x 4'' or 1'' x 6'' Base Trim; Lattice6 x 1-5/8'' 2178500 2136500 1'' x 4'' or 1' x 6'' Base Trim; Ballisters; Lattice7 x 2'' 2179500 2138500 5/4'' x 4'' or 5/4'' x 6'' Radius Edged Decking;

1'' x 4'' or 1'' x 6'' Base Trim; Ballisters; Lattice8 x 2-1/2'' 2180500 2140500 5/4'' x 4'' or 5/4'' x 6'' Radius Edged Decking

2'' x 4'' or 2'' x 6'' Decking2'' x 6'' or 2'' x 8'' Rail Cap or Base Trim

8 x 3'' 2181500 2141500 2'' x 4'' or 2'' x 6'' Decking2'' x 6'' or 2'' x 8'' Rail Cap or Base Trim

10 x 3-1/2'' 2182500 2142500 2'' x 4'' or 2'' x 6'' Decking2'' x 6'' or 2'' x 8'' Rail Cap or Base Trim

Dec-U-Drive Tool 2132910#2 Square Drive Bit 2388910

#2 Square Drive

#2Phillips

Tool RepairStar Sales factory trained technicians and large

parts inventory enable us to provide the most comprehensive repair service in the area.

• Quality workmanship• Rapid turnaround time• Pickup and delivery service is available

257SS 5/19/10 4:54 PM Page 257

258

Fasteners

Product FeaturesGrid-Mate

Low profile design seats flush.

“Keying Windows” provides a strong bond with all coatings.

Climacoat® and Climaseal® fasteners..

Available with stem for time saving pre-spotting of the plate.

Grid-Mate PB

Closure fingers keep coating out of contact with fastener head—no sink marks or bleed throughs.

2" diameter resists and distributes wind loads for a securesystem.

Climacoat and Climaseal fasteners.

ApplicationsGrid-Mate All Polymer Modified (PM) Systems.

Modified Stucco Systems.

Expanded lath over rigid insulation.

Fabric and wire mesh over rigid insulation.

Attaching rigid insulation to wood, steel, masonry, or concrete.

Grid-Mate PB Attaching expanded polystyrene insulationto all substrates for all Polymer Based (PB) ExteriorInsulated Finish Systems (EIFS).

Attaching dense blanket or rigid insulation for parking garages,fireproofing, foundation walls, and soundproofing.

Product SpecificationsGrid-Mate Diameter . . . . . . . . . . . .1-3/4'' Plate

1-3/4'' Plate with stemMaterial . . . . . . . . . . . . .White polypropylene

Grid-Mate PBDiameter . . . . . . . . . . . .2" RoundMaterial . . . . . . . . . . . . .White polypropylene

GRID-MATE™

Mechanical FastenersThe original mechanical fastening system forPolymer Modified (PM) and Modified PB EIFS.

GRID-MATE PB™

Mechanical FastenersThe ultimate fastening system for all PolymerBased (PB) Barrier and Water Managed EIFS.

Part No. 2189900Part No. 2115900 Part No. 2117900

258SS 5/19/10 4:55 PM Page 258

259

Fasteners

GRID-MATE™ and GRIDMATE PB™Gridmate Washers

Tools and Techniques

Use a 0–2500 RPM, 6 amp min. rated screwgun or cordless drillto install fasteners to wood and steel substrates. Use ahammerdrill or rotary hammer to install Tapcon® masonryanchors.

Seat Grid-Mate PB washers flush with or maximum 1/16'' belowinsulation surface. Overdriving may damage the washer andinsulation.

Fasteners

Performance Data Pullout Values (Average lbs. ultimate)

Fasteners must penetrate steel substrates a minimum of 3 pitches of threads.

Replace worn or damaged bit tips to prevent damage to fastener head and its finish.

Consult EIFS system manufacturers specifications forappropriate fastener spacing.

Part Carton CartonNo. Description Quantity Weight2115900 Grid-Mate 1000 4.5 lbs.2117900 Grid-Mate with Stem 1000 5.0 lbs.

Gridmate PB WasherPart Carton CartonNo. Description Quantity Weight2189900 Grid-Mate PB Washer 1000 11 lbs.

Steel ApplicationsSheet Steel Gauges

Fastener 26 24 22 20 18 16 14 12Wood/Light Metal 129 178 244 277 — — — —(Hi-Lo®)Steel (S-12®) — — — 296 471 679 847 1225

Wood ApplicationsFastener Plywood OSB Lumber (Embedment)Wood/Light Metal 1/2" 5/8" 3/4" 1/2" 1/2" 3/4" 1" 1-1/4"(Hi-Lo®) 298 432 633 208 183 304 441 652

Wood/Light MetalFor use with plywood, OSB, dimensional lumberand light gauge metal (26 gauge–20 gauge).

Carton CartonPart No. Description Qty. Wgt.2311500 7 x 1-5/8'' 5000 232312500 8 x 2'' 3500 282313500 8 x 2-1/2'' 2500 212314500 8 x 3'' 2000 202315500 8 x 4'' 1000 122316500 10 x 5'' 500 232317500 10 x 6'' 1000 27

MasonryFor use with brick, block and concrete.

Carton CartonPart No. Description Qty. Wgt.3171407 3/16 x 1-3/4'' 100/500 53173407 3/16 x 2-1/4'' 100/500 63175407 3/16 x 2-3/4'' 100/500 83177407 3/16 x 3-1/4'' 100/500 93181407 3/16 x 4'' 100/500 10

• 5 Carbide Bits Per 500 Piece Master Carton.

Steel FramingFor use with steel framingfrom 20 gauge–12 gauge.

Carton CartonPart No. Description Qty. Wgt.2321500 6 x 1-5/8'' 5000 252318500 6 x 2'' 3500 282319500 8 x 2-5/8'' 2500 262320500 8 x 3'' 2000 242322500 10 x 4'' 1000 212323500 10 x 5'' 500 13

Concrete/Masonry ApplicationsTapcon 3000 PSI Concrete Hollow Block

Diameter Embedment Embedment1" 1-1/4" 1-1/2" 1-3/4" 1" 1-1/4" 1-1/2" 1-3/4"

3/16" 341 581 863 1059 209 357 468 547

The values listed are ultimate averages achieved under laboratoryconditions and apply to Buildex manufactured fasteners only.Appropriate safety factors should be applied to these values for designpurposes. Wind-load test results also available upon request.

259SS 5/19/10 4:55 PM Page 259

260

Fasteners

Approvals Rod Part Screw Box Weight CaseWood Size No. Model Descriptions Qty. (per 125) Qty1/4" 8002957 GST 100 1/4 x 1 25 7.12 1251/4" 8003957 GST 200 1/4 x 2 25 8.64 1251/4" 8004957 GST 300 1/4 x 3 25 9.91 1253/8" 8006957 GST .75 1/4 x 3/4 25 6.24 125

UL 3/8" 8007957 GST 10 1/4 x 1 25 6.68 125UL • FM 3/8" 8008957 GST 20 1/4 x 2 25 8.17 125UL • FM 3/8" 8009925 GST 25-380 3/8 x 2-1/2 25 11.27 125UL • FM 3/8" 8010957 GST 30 1/4 x 3 25 9.41 125

3/8" 8011925 GST 40 1/4 x 4 25 10.01 1253/8" 8012925 GST 60 1/4 x 6 25 12.72 1251/2" 8013925 GST 2 1/4 X 2 25 8.99 1251/2" 8014925 GST 2.5-380 3/8 X 2-1/2 25 11.99 1251/2" 8015925 GST 3 1/4 X 3 25 10.22 1251/2" 8016925 GST 4 1/4 X 4 25 13.25 1251/2" 8017925 GST 6 1/4 X 6 25 13.69 125

vertical mount

Part No. 8113910

Part No. 8114910

Approvals Rod Part Screw Box Weight CaseSteel Size No. Model Descriptions Qty. (per 125) Qty1/4" 8024957 DSTR 100 1/4-20 X 1 25 8.20 1251/4" 8025957 DST 100 1/4-14 X 1 25 7.23 1251/4" 8026957 DST 150 1/4-14 X 1-1/2 25 7.58 1251/4" 8027957 DST 200 1/4-14 X 2 25 8.31 1251/4" 8028957 DST 250 1/4-14 X 2-1/2 25 8.85 1251/4" 8029957 DST 300 1/4-14 X 3 25 9.41 1251/4" 8030957 TEK 500 12-24 X 1-1/2 25 7.39 125

UL • FM 3/8" 8037957 DSTR 1-1/2 12-24 X 1-1/2 25 8.18 125UL • FM 3/8" 8038957 DSTR 1 1/4-20 X 1 25 7.82 125UL • FM 3/8" 8039957 DSTR 516 5/16-18 X 1-1/4 25 9.35 125

3/8" 8040957 DST 10 1/4-14 X 1 25 6.83 1253/8" 8041957 DST 15 1/4-14 X 1-1/2 25 7.20 1253/8" 8042957 DST 20 1/4-14 X 2 25 7.84 1253/8" 8043957 DST 25 1/4-14 X 2-1/2 25 8.42 1253/8" 8044957 DST 30 1/4-14 X 3 25 9.29 125

UL • FM 3/8" 8045957 DST 516 5/16-18 X 1-1/4 25 7.79 125UL • FM 3/8" 8046957 TEK 50 12-24 X 1-1/2 25 6.98 125

1/2" 8031925 DST 2.0 1/4-14 X 2 25 8.61 1251/2" 8032925 DST 2.5 1/4-14 X 2-1/2 25 8.75 1251/2" 8033925 DSTR 1.0 1/4-20 X 1 25 8.61 1251/2" 8034925 DSTR 5.16 5/16-18 X 1-1/4 25 10.10 1251/2" 8035925 DST 5.16 5/16-18 X 1-1/4 25 8.51 1251/2" 8036925 TEK 5.0 12-24 X 1-1/2 25 7.75 125

Approvals Rod Part Screw Box Weight CaseConcrete Size No. Model Descriptions Qty. (per 125) Qty1/4" 8058957 CST 200 5/16 x 1-3/4 25 8.44 125

FM 3/8" 8059957 CST 20 5/16 X 1-3/4 25 7.81 1251/2" 8060925 CST 2 5/16 X 1-3/4 25 8.75 125

black nut driver

red nut driver

260SS 5/19/10 4:56 PM Page 260

261

Fasteners

DEC-KING ® Exterior Wood Screws

Rod Part Screw Box Weight CaseWood Approvals Size No. Model Descriptions Qty. (per 125) Qty1/4" 8018957 SWG 100 1/4 X 1 25 9.32 1251/4" 8019957 SWG 200 1/4 X 2 25 10.78 125

UL 3/8" 8020957 SWG 10 1/4 X 1 25 7.88 125UL 3/8" 8021957 SWG 20 1/4 X 2 25 9.45 125UL 3/8" 8022925 SWG 25-380 3/8 X 2-1/2 25 12.54 125

3/8" 8023925 SWG 30 1/4 X 3 25 10.70 125

Rod Part Screw Box Weight CaseSteel Approvals Size No. Model Descriptions Qty. (per 125) Qty1/4" 8047957 SWD 100 1/4-14 X 1 25 9.35 1251/4" 8049957 SWDR 100 1/4-20 X 1 25 10.37 1253/8" 8050957 SWD 10 1/4-14 X 1 25 8.04 1253/8" 8051957 SWD 15 1/4-14 X 1-1/2 25 8.47 1253/8" 8052957 SWD 20 1/4-14 X 2 25 9.10 1253/8" 8053957 SWD 516 5/16-18 X 1-1/4 25 8.94 125

UL • FM 3/8" 8054957 SWDR 1-1/2 1/4-20 X 1-1/2 25 9.47 125UL • FM 3/8" 8055957 SWDR 1 1/4-20 X 1 25 9.07 125UL • FM 3/8" 8056957 SWDR 516 5/16-18 X 1-1/4 25 10.49 125

3/8" 8057957 SWT 15 12-24 X 1-1/2 25 8.28 125

Rod Part Screw Box Weight CaseConcrete Approvals Size No. Model Descriptions Qty. (per 125) QtyFM 1/4" 8062957 SWC 200 5/16 X 1-3/4 25 11.18 125

3/8" 8061957 SWC 20 5/16 X 1-3/4 25 9.81 125Many items available in Stainless Steel as well as metric sizes.

horizontal mount

Part No. 8114910

Swivel Head® Use with 3/8" RodPart Screw Box Weight Case

Approvals No. Model Descriptions Qty. (per 125) QtyU.S. UL • FM 8139957 SH-GST 20 1/4 x 2 25 8.94 125Patent No. UL • FM 8141957 SH-GST 30 1/4 x 3 25 10.15 1256,443,680 UL • FM 8137957 SH-DSTR 1 1/4-20 x 1 25 9.37 125

• Use #14 Nut Driver(black) Part No. 8113910.

• 17° deflection fromvertical.

• Accommodates up to 3-1/2 x 12 pitch roof.

SAMMY X-Press® Use with 1/4" or 3/8" RodMin.Steel Part Screw Rod Pipe Test Box Weight Case

Approvals Ga. No. Model Descriptions Size Size Load Qty. (per 125) QtyUL 12 ga. 8150922 XP 20 Sammy X-Press 20 3/8-16" 3/4-4" 1475 lbs. 25 10.67 125UL 12 ga. 8153922 XP 35 Sammy X-Press 35 3/8-16" 3/4-4" 1475 lbs. 25 10.61 125UL 22 ga. 8150922 XP 20 Sammy X-Press 20 3/8-16" 3/4-2" 750 lbs. 25 10.67 125UL 18 ga. 8153922 XP 35 Sammy X-Press 35 3/8-16" 3/4-3 1/2" 1250 lbs. 25 10.61 125

Min.Steel Part Screw Rod Load Test Box Weight Case

Approvals Ga. No. Model Descriptions Size Rating Load Qty. (per 125) QtyUL 22 ga. 8150922 XP 20 Sammy X-Press 20 3/8-16" 185 lbs. — 25 10.67 125UL 22 ga. 8153922 XP 35 Sammy X-Press 35 3/8-16" 185 lbs. — 25 10.61 125UL 22 ga. 8181922 XP 200 Sammy X-Press 200 1/4-20" 185 lbs. — 25 11.10 125UL 16 ga. 8150922 XP 20 Sammy X-Press 20 3/8-16" 250 lbs. — 25 10.67 125UL 16 ga. 8153922 XP 35 Sammy X-Press 35 3/8-16" 250 lbs. — 25 10.61 125UL 16 ga. 8181922 XP 200 Sammy X-Press 200 1/4-20" 250 lbs. — 25 11.10 125

8151910 XPIT Sammy X-Press It® Installation Tool — 1 1.02 18152910 XPDB 25/64" Drill Bit — 1 0.14 1

Hang ThreadedRod Directly

fromThin GaugeMetal Deck

& Purlin

Sammy X-Press It®

Installation Tool

U.S. Patent No.6,935,821

261SS 5/19/10 4:56 PM Page 261

262

Fasteners

Power-Bolt™

Heavy-Duty Sleeve AnchorBase MaterialConcrete, Block, Brick, Stone

Size Range1/4" x 1" to 3/4" x 8-1/4”

Anchor MaterialCarbon Steel & Type 304 Stainless Steel

The Power-Bolt™ anchor is a heavy-duty sleeve style self-lockinganchor which is vibration resistant and removable. It is available witha finished hex head or flat head with a hex key insert and can be usedin concrete, block, brick, or stone.

Carbon Steel Hex Head Power-Bolt™Carbon steel Power-Bolt™ anchors are manufactured using a Grade 5bolt. They are plated with a commercial bright zinc finish and have asupplementary chromate treatment in accordance with ASTMSpecification B 633.

304 Stainless Steel Hex Head Power-Bolt™Stainless steel Power-Bolt™ anchors are manufactured from 300series stainless steel (passivated).

* Discontinued item once current stock exhausted.** This size does not have a compression ring.The published length is measured from below the washer to the end of the anchor.

PART DRILL MIN. STD. STD.NO. SIZE DIA. DEPTH BOX CTN.6900 1/4" x 1" 1/4" 7/8" 100 6006902 1/4" x 1-3/4" 1/4" 1-1/4" 100 6006906 1/4" x 3" 1/4" 1-1/4" 100 6006907 5/16" x 1-3/4" 5/16" 1-1/2" 100 6006908 5/16" x 2-1/2" 5/16" 1-1/2" 50 3006909 5/16" x 3-1/2" 5/16" 1-1/2" 50 3006910 3/8" x 2-1/4" 3/8" 2" 50 3006911** 3/8" x 1-7/8" 3/8" 1-1/4" 50 3006913 3/8" x 3" 3/8" 2" 50 3006914 3/8" x 3-1/2" 3/8" 2" 50 3006916 3/8" x 4" 3/8" 2" 50 3006930 1/2" x 2-3/4" 1/2" 2-1/2" 50 2006932 1/2" x 3-3/4" 1/2" 2-1/2" 25 1506934 1/2" x 4-3/4" 1/2" 2-1/2" 25 1506936 1/2" x 5-3/4" 1/2" 2-1/2" 25 1506940 5/8" x 3" 5/8" 2-3/4" 20 1206942 5/8" x 4" 5/8" 2-3/4" 15 906944 5/8" x 5" 5/8" 2-3/4" 15 906945 5/8" x 6" 5/8" 2-3/4" 15 906947 5/8" x 8-1/2" 5/8" 2-3/4" 10 406950 3/4" x 3-1/4" 3/4" 3" 15 906952 3/4" x 4-1/4" 3/4" 3" 10 606954 3/4" x 5-1/4" 3/4" 3" 10 606956 3/4" x 7-1/4" 3/4" 3" 10 406957 3/4" x 8-1/4" 3/4" 3" 10 40

The published length is measured from below the washer to the end of the anchor.1/4" and 5/16" Power-Bolt™ utilize a grade 8 bolt**This size does not have a compression ring.

PART DRILL MIN. STD. STD.NO. SIZE DIA. DEPTH BOX CTN.5900** 1/4" x 1" 1/4" 7/8" 100 6005902 1/4" x 1-3/4" 1/4" 1-1/4" 100 6005906 1/4" x 3" 1/4" 1-1/4" 100 6005910 3/8" x 2-1/4" 3/8" 2" 50 3005914 3/8" x 3-1/2" 3/8" 2" 50 3005916 3/8" x 4" 3/8" 2" 50 3005930 1/2" x 2-3/4" 1/2" 2-1/2" 50 2005934 1/2" x 4-3/4" 1/2" 2-1/2" 25 1505944* 5/8" x 5" 5/8" 2-3/4" 15 905946* 5/8" x 7" 5/8" 2-3/4" 15 605957* 3/4" x 8-1/4" 3/4" 3" 10 40

Carbon Steel Flat Head Power-Bolt™The flat head Power-Bolt™ anchor has a hex key insert formed in thehead of the bolt. Each box contains an Allen wrench which matchesthe insert size.

PART DRILL MIN. STD. STD.NO. SIZE DIA. DEPTH BOX CTN.6981 3/8" x 3-3/4" 3/8" 2" 50 3006982 3/8" x 5" 3/8" 2" 50 3006983 3/8" x 6" 3/8" 2" 50 3006984 1/2" x 5" 1/2" 2-1/2" 25 1506987 5/8" x 5-1/2" 5/8" 2-3/4" 15 90

PART MIN. THREAD STD. STD.NO. SIZE DEPTH DEPTH BOX CTN.6400 1/4" 1-1/8" 1/4" 100 10006401 3/8" 1-3/8" 5/16" 50 500

The published length is the overall length of the anchor.

ANCHOR SIZES

Power-Stud™

Wedge Type Expansion AnchorBase MaterialConcrete, Grouted CMU

Size Range1/4" x 1-3/4" to 1-1/4" x 12"

Anchor MaterialCarbon Steel, Type 304 or 316 Stainless Steel, & MechanicallyGalvanized Carbon Steel

The Power-Stud™ anchor is a one piece fully threaded, wedge styleanchor available in carbon steel and stainless steel. Threaded, RodHanger and Tie-Wire versions are designed for use in solid concrete.The drill bit diameter needed for proper installation is the same as theanchor diameter.

262SS 5/19/10 4:57 PM Page 262

263

Fasteners

Carbon Steel Power-Stud™Carbon Steel Power-Stud™ anchors are manufactured from carbonsteel which is plated with commercial bright zinc and a supplementarychromate treatment in accordance with ASTM Specification B 633,SC1, Type III.

PART MIN. THREAD STD. STD.NO. SIZE EMBED. LENGTH BOX CTN.7400 1/4" x 1-3/4" 1-1/8" 3/4" 100 5007402 1/4" x 2-1/4" 1-1/8" 1-1/4" 100 5007404 1/4" x 3-1/4" 1-1/8" 2-1/4" 100 5007410 3/8" x 2-1/4" 1-5/8" 1-1/4" 50 2507412 3/8" x 2-3/4" 1-5/8" 1-5/8" 50 2507413 3/8" x 3" 1-5/8" 1-7/8" 50 2507414 3/8" x 3-1/2" 1-5/8" 2-3/8" 50 2507415 3/8" x 3-3/4" 1-5/8" 2-5/8" 50 2507416 3/8" x 5" 1-5/8" 3-7/8" 50 2507417 3/8" x 7" 1-5/8" 5-7/8" 50 2007420 1/2" x 2-3/4" 2-1/4" 1-3/8" 50 2007422 1/2" x 3-3/4" 2-1/4" 2-3/8" 50 2007423 1/2" x 4-1/2" 2-1/4" 3-1/8" 50 2007424 1/2" x 5-1/2" 2-1/4" 4-1/8" 50 1507426 1/2" x 7" 2-1/4" 5-5/8" 25 1007427 1/2" x 8-1/2" 2-1/4" 7-1/8" 25 1007430 5/8" x 3-1/2" 2-3/4" 2" 25 1007432 5/8" x 4-1/2" 2-3/4" 3" 25 1007433 5/8" x 5" 2-3/4" 3-1/2" 25 1007434 5/8" x 6" 2-3/4" 4-1/2" 25 757436 5/8" x 7" 2-3/4" 5-1/2" 25 757438 5/8" x 8-1/2" 2-3/4" 7" 25 757439 5/8" x 10" 2-3/4" 8-1/2" 25 757440 3/4" x 4-1/4" 3-3/8" 2-3/8" 20 607441 3/4" x 4-3/4" 3-3/8" 2-7/8" 20 607442 3/4" x 5-1/2" 3-3/8" 3-5/8" 20 607444 3/4" x 6-1/4" 3-3/8" 4-3/8" 20 607446 3/4" x 7" 3-3/8" 5-1/8" 20 607448 3/4" x 8-1/2" 3-3/8" 6-5/8" 10 407449 3/4" x 10" 3-3/8" 8-1/8" 10 307451 3/4" x 12" 3-3/8" 10-1/8" 10 307450 7/8" x 6" 3-7/8" 2-3/4" 10 407452 7/8" x 8" 3-7/8" 4-3/4" 10 407454 7/8" x 10" 3-7/8" 6-3/4" 10 307461 1" x 6" 4-1/2" 2-3/8" 10 307463 1" x 9" 4-1/2" 5-3/8" 10 307465 1" x 12" 4-1/2" 8-3/8" 5 157473 1-1/4" x 9" 5-5/8" 4-3/4" 5 157475 1-1/4" x 12" 5-5/8" 7-3/4" 5 15

The published length is the overall length of the anchor. Allow for fixture thickness plusone anchor diameter for the nut and washer thickness when selecting a length.

PART MIN. THREAD STD. STD.NO. SIZE EMBED. LENGTH BOX CTN.7720 1/2" x 2-3/4" 2-1/4" 1-3/8" 50 2007723 1/2" x 4-1/2" 2-1/4" 3-1/8" 50 2007724 1/2" x 5-1/2" 2-1/4" 4-1/8" 50 1507726 1/2" x 7" 2-1/4" 5-5/8" 25 1007730 5/8" x 3-1/2" 2-3/4" 2" 25 1007734 5/8" x 6" 2-3/4" 4-1/2" 25 757741 3/4" x 4-3/4" 3-3/8" 2-7/8" 20 607742 3/4" x 5-1/2" 3-3/8" 3-5/8" 20 607748 3/4" x 8-1/2" 3-3/8" 6-5/8" 10 407750 7/8" x 6" 3-7/8" 2-3/4" 10 407752 7/8" x 8" 3-7/8" 4-3/4" 10 407763 1" x 9" 4-1/2" 5-3/8" 10 30

PART MIN. THREAD STD. STD.NO. SIZE EMBED. LENGTH BOX CTN.7300 1/4" x 1-3/4" 1-1/8" 3/4" 100 5007302 1/4" x 2-1/4" 1-1/8" 1-1/4" 100 5007304 1/4" x 3-1/4" 1-1/8" 2-1/4" 100 5007310 3/8" x 2-1/4" 1-5/8" 1-1/4" 50 2507312 3/8" x 2-3/4" 1-5/8" 1-5/8" 50 2507313 3/8" x 3" 1-5/8" 1-7/8" 50 2507314 3/8" x 3-1/2" 1-5/8" 2-3/8" 50 2507315 3/8" x 3-3/4" 1-5/8" 2-5/8" 50 2507316 3/8" x 5" 1-5/8" 3-1/8" 50 2507320 1/2" x 2-3/4" 2-1/4" 1-3/8" 50 2007322 1/2" x 3-3/4" 2-1/4" 2-3/8" 50 2007323 1/2" x 4-1/2" 2-1/4" 3-1/8" 50 2007324 1/2" x 5-1/2" 2-1/4" 4-1/8" 50 1507326 1/2" x 7" 2-1/4" 5-5/8" 25 1007330 5/8" x 3-1/2" 2-3/4" 2" 25 1007332 5/8" x 4-1/2" 2-3/4" 3" 25 1007333 5/8" x 5" 2-3/4" 3-1/2" 25 1007334 5/8" x 6" 2-3/4" 4-1/2" 25 75

PART TIE-WIRE MIN. STD. STD.NO. SIZE HOLE SIZE EMBED. BOX CTN.7409 1/4" x 2" 9/32" 1-1/8" 100 500

Tie-Wire Power-Stud™

Mechanically Galvanized Power-Stud™Mechanically Galvanized Power-Stud™ anchors are manufacturedfrom steel which have a mechanically galvanized coating (zinc) inaccordance with ASTM Specification B 695, Class 65, Type I.

Type 304 Stainless Steel Hex Head Power-Stud™Stainless Steel Power-Stud™ anchors are manufactured from AISIType 304 / 304 Cu and Type 316 stainless steel which is passivated.

PART ROD ANCHOR DRILL MIN. THREAD STD. STD.NO. SIZE SIZE DIA. EMBED. DEPTH BOX CTN.7806 3/8" 1/2"x 2-3/8" 1/2" 2-1/4" 9/16" 50 250

Rod Hanger Power-Stud™

263SS 5/19/10 4:57 PM Page 263

264

Fasteners

PART MIN. THREAD STD. STD.NO. SIZE EMBED. LENGTH BOX CTN.7336 5/8" x 7" 2-3/4" 5-1/2" 25 757338 5/8" x 8-1/2" 6-7/8" 7" 25 757340 3/4" x 4-1/4" 3-3/8" 2-3/8" 20 607341 3/4" x 4-3/4" 3-3/8" 2-7/8" 20 607342 3/4" x 5-1/2" 3-3/8" 3-5/8" 20 607344 3/4" x 6-1/4" 3-3/8" 4-3/8" 20 607346 3/4" x 7" 3-3/8" 5-1/8" 20 607348 3/4" x 8-1/2" 3-3/8" 6-5/8" 10 407349 3/4" x 10" 3-3/8" 8-1/8" 10 307352 7/8" x 8" 3-7/8" 4-3/4" 10 407361 1" x 6" 4-1/2" 2-3/8" 10 307363 1" x 9" 4-1/2" 5-3/8" 10 307365 1" x 12" 4-1/2" 8-3/8" 5 15

Type 304 Stainless Steel Hex Head Power-Stud™ (cont.)



PART MIN. THREAD STD. STD.NO. SIZE EMBED. LENGTH BOX CTN.7600 1/4" x 1-3/4" 1-1/8" 3/4" 100 5007602 1/4" x 2-1/4" 1-1/8" 1-1/4" 100 5007604 1/4" x 3-1/4" 1-1/8" 2-1/4" 100 5007610 3/8" x 2-1/4" 1-5/8" 1-1/4" 50 2507612 3/8" x 2-3/4" 1-5/8" 1-5/8" 50 2507613 3/8" x 3" 1-5/8" 1-7/8" 50 2507614 3/8" x 3-1/2" 1-5/8" 2-3/8" 50 2507615 3/8" x 3-3/4" 1-5/8" 2-5/8" 50 2507616 3/8" x 5" 1-5/8" 3-7/8" 50 2507620 1/2" x 2-3/4" 2-1/4" 1-3/8" 50 2007622 1/2" x 3-3/4" 2-1/4" 2-3/8" 50 2007623 1/2" x 4-1/2" 2-1/4" 3-1/8" 50 2007624 1/2" x 5-1/2" 2-1/4" 4-1/8" 50 1507626 1/2" x 7" 2-1/4" 5-5/8" 25 1007630 5/8" x 3-1/2" 2-3/4" 2" 25 1007632 5/8" x 4-1/2" 2-3/4" 3" 25 1007633 5/8" x 5" 2-3/4" 3-1/2" 25 1007634 5/8" x 6" 2-3/4" 4-1/2" 25 757636 5/8" x 7" 2-3/4" 5-1/2" 25 757638 5/8" x 8-1/2" 2-3/4" 7" 25 757640 3/4" x 4-1/4" 3-3/8" 2-3/8" 20 607641 3/4" x 4-3/4" 3-3/8" 2-7/8" 20 607642 3/4" x 5-1/2" 3-3/8" 3-5/8" 20 607644 3/4" x 6-1/4" 3-3/8" 4-3/8" 20 607646 3/4" x 7" 3-3/8" 5-1/8" 20 607648 3/4" x 8-1/2" 3-3/8" 6-5/8" 10 40

Type 316 Stainless Steel Power-Stud™

Acorn Nut Lok-Bolt™ Carbon Steel

Lok-Bolt™

Sleeve Type Expansion AnchorBase MaterialConcrete, Block, BrickSize Range1/4" x 5/8" to 3/4" x 7-1/2"Anchor MaterialCarbon Steel & Stainless Steel

The Lok-Bolt™ anchor is a pre-assembled single unit sleeve anchoravailable in carbon steel and stainless steel which can be used inconcrete, block, brick and stone. Extension sleeves are added tocreate longer lengths.

Hex Nut Lok-Bolt™ Carbon SteelPART DRILL MIN. STD. STD.NO. SIZE DIA. EMBED. BOX CTN.5005 5/16" x 1-1/2" 5/16" 1-3/8" 100 10005010 5/16" x 2-1/2" 5/16" 1-1/2" 100 5005015 3/8" x 1-7/8" 3/8" 1-5/8" 50 5005020 3/8" x 3" 3/8" 1-5/8" 50 5005022 3/8" x 4" 3/8" 1-5/8" 50 2505025 1/2" x 2-1/4" 1/2" 2-1/8" 25 2505030 1/2" x 3" 1/2" 2-1/4" 25 2505034 1/2" x 4" 1/2" 2-1/4" 25 1255033 1/2" x 5-1/4" 1/2" 2-1/4" 25 1255032 1/2" x 6" 1/2" 2-1/4" 10 1005035 5/8" x 2-1/4" 5/8" 2-1/8" 25 1255038 5/8" x 3" 5/8" 2-3/4" 25 1255040 5/8" x 4-1/4" 5/8" 2-3/4" 10 1005045 5/8" x 6" 5/8" 2-3/4" 10 1005050 3/4" x 2-1/2" 3/4" 2-1/8" 10 1005055 3/4" x 4" 3/4" 3-3/8" 10 405060 3/4" x 5-3/4" 3/4" 3-3/8" 10 305065 3/4" x 7-1/2" 3/4" 3-3/8" 10 30

The published length is measured from below the washer to the end of the anchor.

The published length is measured from below the washer to the end of the anchor.**This size does not have a compression ring.


Hex Nut Lok-Bolt™ 304 Stainless SteelPART DRILL MIN. STD. STD.NO. SIZE DIA. EMBED. BOX CTN.6152 3/8" x 1-7/8" 3/8" 1-5/8" 50 5006153 3/8" x 3" 3/8" 1-5/8" 50 5006156 1/2" x 2-1/4" 1/2" 2-1/8" 25 2506157 1/2" x 3" 1/2" 2-1/4" 25 2506160 1/2" x 4" 1/2" 2-1/4" 25 1256164 5/8" x 4-1/4" 5/8" 2-3/4" 10 1006168 3/4" x 4" 3/4" 3-3/8" 10 40

PART DRILL MIN. STD. STD.NO. SIZE DIA. EMBED. BOX CTN.5125** 1/4" x 5/8" 1/4" 1/2" 100 10005150 1/4" x 1-3/8" 1/4" 1-1/8" 100 10005175 1/4" x 2-1/4" 1/4" 1-1/8" 100 1000

264SS 5/19/10 4:57 PM Page 264

265

Fasteners

Rod Hanger Lok-Bolt™ Carbon Steel

Acorn Nut Lok-Bolt™ 304 Stainless Steel


PART DRILL MIN. STD. STD.NO. SIZE DIA. EMBED. BOX CTN.6150 1/4" x 1-3/8" 1/4" 1-1/8" 100 1000

Round Head Lok-Bolt™ 304 Stainless SteelPART DRILL MIN. STD. STD.NO. SIZE DIA. EMBED. BOX CTN.6180 1/4" x 2" 1/4" 1-1/8" 100 1000

Lok-Bolt™ Extenders 304 Stainless Steel (for additional length)

PART DRILL STD. STD.NO. SIZE DIA. BOX CTN.5687* 1/4 x 1" 1/4" 100 10005690* 1/2 x 1-3/8" 1/2" 25 125

Lok-Bolt™ Multiple Use KitPART DRILL MIN. STD. STD.NO. SIZE DIA. DEPTH BOX CTN.5660* 1/2" 1/2" 2-1/4" 25 250

Round Head Lok-Bolt™ Carbon Steel

*Discontinued item once current stock exhausted.**This size does not have a compression ring.

*Discontinued item once current stock exhausted.Includes 25 expander sleeves, cones, nuts, and washers for use with a 3/8" rod

*Discontinued item once current stock exhausted.

PART DRILL MIN. STD. STD.NO. SIZE DIA. EMBED. BOX CTN.5205** 1/4" x 1-1/8" 1/4" 1" 100 10005210 1/4" x 2" 1/4" 1-1/8" 100 10005215 1/4" x 2-3/4" 1/4" 1-1/8" 100 10005225* 5/16" x 2-3/8" 5/16" 1-1/2" 100 10005230* 5/16" x 3-3/8" 5/16" 1-1/2" 100 5005235 3/8" x 2-1/2" 3/8" 1-5/8" 50 5005240 3/8" x 3-3/4" 3/8" 1-5/8" 50 250

Lok-Bolt™ Extenders Carbon Steel (for additional length)

PART DRILL MIN. STD. STD.NO. SIZE DIA. EMBED. BOX CTN.5684 3/8 x 1-1/4" 3/8" 50 500

Threshold Flat Head Lok-Bolt™

Tie-Wire Lok-Bolt™

Combo Flat Head Lok-Bolt™ Carbon Steel

**This size does not have a compression ring.

PART DRILL MIN. STD. STD.NO. SIZE DIA. EMBED. BOX CTN.5305** 1/4" x 1-1/8" 1/4" 1" 100 10005310 1/4" x 2" 1/4" 1-1/8" 100 10005315 1/4" x 3" 1/4" 1-1/8" 100 10005320 1/4" x 4" 1/4" 1-1/8" 100 5005325 1/4" x 5-1/4" 1/4" 1-1/8" 100 5005330 5/16" x 2-1/2" 5/16" 1-1/2" 100 10005340 3/8" x 2-3/4" 3/8" 1-5/8" 50 5005345 3/8" x 4" 3/8" 1-5/8" 50 2505350 3/8" x 5" 3/8" 1-5/8" 50 2505360 3/8" x 6" 3/8" 1-5/8" 50 250

Combo Flat Head Lok-Bolt™ 304 Stainless Steel

These parts do not have a compression ring.

PART DRILL MIN. STD. STD.NO. SIZE DIA. EMBED. BOX CTN.6170 1/4" x 2" 1/4" 1-1/8" 100 10006172 1/4" x 3" 1/4" 1-1/8" 100 10006174 3/8" x 4" 3/8" 1-5/8" 50 2506175 3/8" x 5" 3/8" 1-5/8" 50 2506176 3/8" x 6" 3/8" 1-5/8" 50 250

This part does not have a compression ring.

**This size does not have a compression ring.

PART DRILL MIN. STD. STD.NO. SIZE DIA. EMBED. BOX CTN.5500 1/4" x 2" 1/4" 1-1/8" 100 1000

PART DRILL MIN. STD. STD.NO. SIZE DIA. EMBED. BOX CTN.5810 1/4" x 1-1/2" 5/16" 1-1/2" 50 2505815** 3/8" x 1-7/8" 3/8" 1-7/8" 50 2505825** 1/2" x 2-1/4" 1/2" 2-1/4" 25 125

PART DRILL MIN. STD. STD.NO. SIZE DIA. DEPTH BOX CTN.5700 5/16" x 1-1/2" 5/16" 1-1/2" 100 1000

Set-Bolt™

Displacement Controlled Expansion AnchorBase MaterialConcreteSize Range1/4" x 1-3/4" to 1/2" x 4-1/4"Anchor MaterialCarbon Steel

The Set-Bolt™ is a one piece, stud style anchor with an externalbottom-bearing expansion plug. It is available in carbon steel for usein concrete, stone and solid masonry units.

265SS 5/19/10 4:58 PM Page 265

266

Fasteners

TAPPER™

Concrete ScrewBase MaterialConcrete, Block and Brick

Size Range3/16" x 1-1/4" to 3/8" x 6"

Anchor MaterialCarbon Steel, Type 304 & Type 410 Stainless Steel

The TAPPER™ Anchoring System is a family of screw anchors,specially designed drill bits and installation tools designed to meetthe needs of most light to medium duty applications in concrete,block and brick. The TAPPER™ concrete screw anchor is produced ineither hex washer head or Phillips flat head styles from Perma-Seal™coated or zinc plated carbon steel and Type 304 and Type 410stainless steel. For heavy duty applications, the 3/8" size is made inzinc plated carbon steel.

Wedge-Bits™

SDS-Plus Wedge-Bit™For proper performance, the Wedge-Bolt and 410 Stainless SteelWedge-Bolt anchors must be installed with a Wedge-Bit. The Wedge-Bit has a special matched tolerance range designed toprovide optimum performance for the anchor. The available shankstyles and sizes are listed below.

PART DRILL USABLE OVERALL STD.NO. SIZE LENGTH LENGTH POUCH.1312 1/4" 2" 4" 11314 1/4" 4" 6" 11316 3/8" 4" 6" 11318 3/8" 6" 8" 11332 3/8" 10" 12" 11320 1/2" 4" 6" 11322 1/2" 8" 10" 11324 5/8" 6" 8" 11334 1/2" 10" 12" 11326 5/8" 10" 12" 11336 5/8" 16" 18" 1101293 5/8" 16" 21" 11328 3/4" 6" 8" 11330 3/4" 10" 12" 1

Heavy-Duty Straight Shank Wedge-Bit™PART DRILL USABLE OVERALL STD.NO. SIZE LENGTH LENGTH POUCH.1370 1/4" 2 3/4" 4" 11372 1/4" 4" 6" 11380 3/8” 4" 6" 11384 3/8" 11" 13" 11390 1/2" 4" 6" 11394 1/2" 11" 13" 11396 5/8" 11" 13" 11397 3/4" 11" 13" 1

Spline Wedge-Bit™PART DRILL USABLE OVERALL STD.NO. SIZE LENGTH LENGTH POUCH.1340 1/2" 8" 13" 11342 1/2" 11" 16" 11344 5/8" 8" 13" 11348 3/4" 8" 13" 1

SDS-Max Wedge-Bit™PART DRILL USABLE OVERALL STD.NO. SIZE LENGTH LENGTH POUCH.1354 1/2" 8" 13" 11356 5/8" 8" 13" 1101293 5/8" 16" 21" 11358 3/4" 8" 13" 1

Blue Perma-Seal™ Tapper™ Hex HeadStandard Packaging — 100 Screws and 1 Drill Per Box

PART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX2700 3/16" x 1-1/4" 100 500 2781 27932702 3/16" x 1-3/4" 100 500 2781 27932704 3/16" x 2-1/4" 100 500 2782 27932706 3/16" x 2-3/4" 100 500 2782 27932708 3/16" x 3-1/4" 100 500 2783 27942710 3/16" x 3-3/4" 100 500 2783 27942712 3/16" x 4" 100 500 2783 27942720 1/4" x 1-1/4" 100 500 2785 27962722 1/4" x 1-3/4" 100 500 2785 27962724 1/4" x 2-1/4" 100 500 2786 27962726 1/4" x 2-3/4" 100 500 2786 27962728 1/4" x 3-1/4" 100 500 2787 27972730 1/4" x 3-3/4" 100 500 2787 27972732 1/4" x 4" 100 500 2787 2797

Master PackPART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX9462 3/16" x 1-1/4" 2000 2000 2781 27939463 3/16" x 1-3/4" 2000 2000 2781 27939464 3/16" x 2-1/4" 2000 2000 2782 27939465 3/16" x 2-3/4" 2000 2000 2782 27939466 3/16" x 3-1/4" 1000 1000 2783 27949467 3/16" x 3-3/4" 1000 1000 2783 27949468 3/16" x 4" 1000 1000 2783 27949469 1/4" x 1-1/4" 2000 2000 2785 27969470 1/4" x 1-3/4" 2000 2000 2785 27969471 1/4" x 2-1/4" 1000 1000 2786 27969472 1/4" x 2-3/4" 1000 1000 2786 27969473 1/4" x 3-1/4" 1000 1000 2787 27979474 1/4" x 3-3/4" 1000 1000 2787 27979475 1/4" x 4" 1000 1000 2787 2797

266SS 5/19/10 4:58 PM Page 266

267

Fasteners

Blue Perma-Seal™ Tapper™ Phillips Flat HeadStandard Packaging — 100 Screws and 1 Drill Per Box

†Stainless Steel TAPPER™ screws require the use of special TAPPER™ drill bits. Thesespecial drill bits are gold or silver colored for identification. They cannot be used with thePerma-Seal™ TAPPER™.

PART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX2740 3/16" x 1-1/4" 100 500 2781 27932742 3/16" x 1-3/4" 100 500 2781 27932744 3/16" x 2-1/4" 100 500 2782 27932746 3/16" x 2-3/4" 100 500 2782 27932748 3/16" x 3-1/4" 100 500 2783 27942750 3/16" x 3-3/4" 100 500 2783 27942752 3/16" x 4" 100 500 2783 27942760 1/4" x 1-1/4" 100 500 2785 27962762 1/4" x 1-3/4" 100 500 2785 27962764 1/4" x 2-1/4" 100 500 2786 27962766 1/4" x 2-3/4" 100 500 2786 27962768 1/4" x 3-1/4" 100 500 2787 27972770 1/4" x 3-3/4" 100 500 2787 27972772 1/4" x 4" 100 500 2787 27972774 1/4" x 5" 100 100 2788 —2776 1/4" x 6" 100 100 2789 —

Type 304 Stainless Steel Tapper™† Hex HeadStandard Packaging — 100 Screws and 1 Drill Per Box

PART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX2880 1/4" x 1-1/4" 100 500 2894 27902881 1/4" x 1-3/4" 100 500 2894 27902882 1/4" x 2-1/4" 100 500 2895 27902883 1/4" x 2-3/4" 100 500 2895 2790

†Stainless Steel TAPPER™ screws require the use of special TAPPER™ drill bits. Thesespecial drill bits are gold or silver colored for identification. They cannot be used with thePerma-Seal™ TAPPER™.

Type 304 Stainless Steel Tapper™† Phillips Flat HeadStandard Packaging — 100 Screws and 1 Drill Per Box

PART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX2887 1/4" x 1-1/4" 100 500 2894 27902888 1/4" x 1-3/4" 100 500 2894 27902889 1/4" x 2-1/4" 100 500 2895 27902890 1/4" x 2-3/4" 100 500 2895 2790

Type 410 Stainless Steel Tapper™ Hex HeadStandard Packaging — 100 Screws and 1 Drill Per Box

PART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX4110 1/4” x 1-1/4” 100 500 2785 27964112 1/4” x 1-3/4” 100 500 2785 27964114 1/4” x 2-1/4” 100 500 2786 27964116 1/4” x 2-3/4” 100 500 2786 2796

Type 410 Stainless Steel Tapper™ Phillips Flat HeadStandard Packaging — 100 Screws and 1 Drill Per Box

PART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX4118 1/4” x 1-1/4” 100 500 2785 27964120 1/4” x 1-1/2” 100 500 2785 27964123 1/4” x 2-1/4” 100 500 2786 27964124 1/4” x 2-3/4” 100 500 2786 27964125 1/4” x 3-1/4” 100 500 2786 27964126 1/4” x 3-3/4” 100 500 2786 2796

Master PackPART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX9476 3/16" x 1-1/4" 2000 2000 2781 27939477 3/16" x 1-3/4" 2000 2000 2781 27939478 3/16" x 2-1/4" 2000 2000 2782 27939479 3/16" x 2-3/4" 2000 2000 2782 27939480 3/16" x 3-1/4" 1000 1000 2783 27949481 3/16" x 3-3/4" 1000 1000 2783 27949482 3/16" x 4" 1000 1000 2783 27949483 1/4" x 1-1/4" 2000 2000 2785 27969484 1/4" x 1-3/4" 2000 2000 2785 27969485 1/4" x 2-1/4" 1000 1000 2786 27969486 1/4" x 2-3/4" 1000 1000 2786 27969487 1/4" x 3-1/4" 1000 1000 2787 27979488 1/4" x 3-3/4" 1000 1000 2787 27979489 1/4" x 4" 1000 1000 2787 27979490 1/4" x 5" 1000 1000 2788 —9491 1/4" x 6" 500 500 2789 —

267SS 5/19/10 4:58 PM Page 267

268

Fasteners

White Perma-Seal™ Tapper™ Hex HeadStandard Packaging — 100 Screws and 1 Drill Per Box


Master PackPART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX9923 1/4" x 1-1/4" 2000 2000 2785 27969924 1/4" x 1-3/4" 2000 2000 2785 27969927 1/4" x 3-1/4" 1000 1000 2787 27979928 1/4" x 3-3/4" 1000 1000 2787 27979929 1/4" x 4" 1000 1000 2787 2797

Master PackPART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX9191 3/16" x 1-1/4" 2000 2000 2781 27939192 3/16" x 1-3/4" 2000 2000 2781 27939193 3/16" x 2-1/4" 1000 1000 2782 27939194 3/16" x 2-3/4" 1000 1000 2782 27939195 3/16" x 3-1/4" 1000 1000 2783 27949196 3/16" x 3-3/4" 1000 1000 2783 27949197 3/16" x 4" 1000 1000 2783 27949951 1/4" x 1-1/4" 2000 2000 2785 27969952 1/4" x 1-3/4" 2000 2000 2785 27969953 1/4" x 2-1/4" 2000 2000 2786 27969954 1/4" x 2-3/4" 2000 2000 2786 27969955 1/4" x 3-1/4" 1000 1000 2787 27979956 1/4" x 3-3/4" 1000 1000 2787 27979957 1/4" x 4" 1000 1000 2787 27979958 1/4" x 5" 1000 1000 2788 —9959 1/4" x 6" 500 500 2789 —

White Perma-Seal™ Tapper™ Phillips Flat HeadStandard Packaging — 100 Screws and 1 Drill Per Box


3/8" Zinc Plated Carbon Steel Tapper™ Flange Hex HeadStandard Packaging — 100 Screws and 1 Drill Per Box

PART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX5804 3/8" x 2" 100 500 5860 58665806 3/8" x 3" 100 500 5860 58665808 3/8" x 4" 100 500 5861 5868

White Perma-Seal™ Tapper™ Flange Hex HeadPART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX8706 1/4" x 1-3/4" 100 500 2785 27968707 1/4" x 2-1/4" 100 500 2786 27968708 1/4" x 2-3/4" 100 500 2786 27968709 1/4" x 3-1/4" 100 500 2787 2797

White Perma-Seal™ Tapper™ Trim Flat HeadPART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX8710 1/4" x 1-3/4" 100 500 2785 27968711 1/4" x 2-1/4" 100 500 2786 27968712 1/4" x 2-3/4" 100 500 2786 27968713 1/4" x 3-1/4" 100 500 2787 27978714 1/4" x 3-3/4" 100 500 2787 2797

268SS 5/20/10 4:17 PM Page 268

269

Fasteners

Silver Perma-Seal™ Tapper™ Hex HeadPART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX2400 3/16" x 1-1/4" 100 500 2781 27932402 3/16" x 1-3/4" 100 500 2781 27932404 3/16" x 2-1/4" 100 500 2782 27932406 3/16" x 2-3/4" 100 500 2782 27932408 3/16" x 3-1/4" 100 500 2783 27942410 3/16" x 3-3/4" 100 500 2783 27942412 3/16" x 4" 100 500 2783 27942486 1/4” x 1-1/4" 100 500 2785 27962488 1/4” x 1-3/4” 100 500 2785 27962490 1/4” x 2-1/4” 100 500 2786 27962492 1/4” x 2-3/4” 100 500 2786 27962494 1/4” x 3-1/4” 100 500 2787 27972495 1/4” x 3-3/4” 100 500 2787 27972496 1/4” x 4” 100 500 2787 2797

Silver Perma-Seal™ Tapper™ Flange Hex HeadPART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX8715 1/4” x 1-3/4” 100 500 2785 27968716 1/4” x 2-1/4” 100 500 2786 27968717 1/4” x 2-3/4” 100 500 2786 27968718 1/4” x 3-1/4” 100 500 2787 2797

Master PackPART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX8750 1/4” x 1-1/4” 2000 2000 2785 27968751 1/4” x 1-3/4” 2000 2000 2785 27968752 1/4” x 2-1/4” 2000 2000 2786 27968753 1/4” x 2-3/4” 2000 2000 2786 27968754 1/4” x 3-1/4” 1000 1000 2787 27978755 1/4” x 3-3/4” 1000 1000 2787 27978756 1/4” x 4” 1000 1000 2787 2797

Master PackPART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX8757 3/16” x 1-1/4” 2000 2000 2781 27938758 3/16” x 1-3/4” 2000 2000 2781 27938759 3/16” x 2-1/4” 1000 1000 2782 27938760 3/16” x 2-3/4” 1000 1000 2782 27938761 3/16” x 3-1/4” 1000 1000 2783 27948762 3/16” x 3-3/4” 1000 1000 2783 27948763 3/16” x 4” 1000 1000 2783 27948764 1/4” x 1-1/4” 2000 2000 2785 27968765 1/4” x 1-3/4” 2000 2000 2785 27968766 1/4” x 2-1/4” 2000 2000 2786 27968767 1/4” x 2-3/4” 2000 2000 2786 27968768 1/4” x 3-1/4” 1000 1000 2787 27978769 1/4” x 3-3/4” 1000 1000 2787 27978770 1/4” x 4” 1000 1000 2787 2797

3/8" Zinc Plated Carbon Steel Tapper™ Flange PHFStandard Packaging — 100 Screws and 1 Drill Per Box

PART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX5852 3/8" x 3" 100 500 5860 58665854 3/8" x 4" 100 500 5861 58685856 3/8" x 5" 100 100 5862 58685858 3/8" x 6" 100 100 5863 5868

Silver Perma-Seal™ Tapper™ Phillips Flat HeadPART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX2498 3/16” x 1-1/4” 100 500 2781 27932500 3/16” x 1-3/4” 100 500 2781 27932501 3/16” x 2-1/4” 100 500 2782 27932502 3/16” x 2-3/4” 100 500 2782 27932503 3/16” x 3-1/4” 100 500 2783 27942504 3/16” x 3-3/4” 100 500 2783 27942505 3/16” x 4” 100 500 2783 27942506 1/4” x 1-1/4” 100 500 2785 27962507 1/4” x 1-3/4” 100 500 2785 27962508 1/4” x 2-1/4” 100 500 2786 27962509 1/4” x 2-3/4” 100 500 2786 27962510 1/4” x 3-1/4” 100 500 2787 27972511 1/4” x 3-3/4” 100 500 2787 27972512 1/4” x 4” 100 500 2787 2797

Bronze Tapper™ Flange Hex HeadPART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX9977 1/4” x 1-3/4” 100 500 2785 27969978 1/4” x 2-1/4” 100 500 2786 2796

Bronze Tapper™ Flange Hex HeadPART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX9975 1/4” x 1-3/4” 100 500 2785 27969976 1/4” x 2-1/4” 100 500 2786 2796

Silver Perma-Seal™ Tapper™ Trim Flat HeadPART STD. STD. DRILL REFERENCESNO. SIZE BOX CTN. STRAIGHT SDS HEX8719 1/4” x 1-3/4” 100 500 2785 27968720 1/4” x 2-1/4” 100 500 2786 27968721 1/4” x 2-3/4” 100 500 2786 27968722 1/4” x 3-1/4” 100 500 2787 27978723 1/4” x 3-3/4” 100 500 2787 2797

269SS 5/19/10 4:59 PM Page 269

270

Fasteners

Carbide Drill Bits for Perma-Seal™ and 410 SS Tapper™TAPPER™ Drill Bits in the diameters listed are nominal size. 3/16"and 1/4" Perma-Seal™ TAPPER™ anchors must be installed withspecial tolerance TAPPER™ drill bits. 1/4" Stainless Steel TAPPER™anchors require the use of specific tolerance TAPPER™ drill bits,which are gold or silver colored, to denote the standard size andspecial application size for harder materials. 3/8" diameter TAPPER™anchors should be installed with a 1/4" ANSI drill bit.

Tolerance Range = 0.168" to 0.175" for the 5/32" and 0.202" to 0.204"for the 3/16" bits. (Do not use with Type 304 Stainless SteelTAPPER™)

Installation Tools for 3/16" and 1/4" Tapper™

CONDRIVE®† 2000 Replacement Parts

SDS Hex

Straight ShankPART USABLE STD.NO. SIZE LENGTH TUBE2781 5/32" x 3-1/2" 2" 102782 5/32" x 4-1/2" 3" 102783 5/32" x 5-1/2" 4" 102785 3/16" x 3-1/2" 2" 102786 3/16" x 4-1/2" 3" 102787 3/16" x 5-1/2" 4" 102788 3/16" x 6-1/2" 5" 102789 3/16" x 7-1/2" 6" 10

PART USABLE STD.NO. SIZE LENGTH TUBE2793 5/32" x 5" 3" 12794 5/32" x 7" 5" 12796 3/16" x 5" 3" 12797 3/16" x 7" 5" 1

Tapper™ Drill Bits

Tapper™ Installation Tools

Carbide Drill Bits for Type 304 SS Tapper™This is the standard bit for use with Type 304 Stainless SteelTAPPER™. It is for use in standard weight concrete and block,tolerance = 0.215" to 0.216". This bit is gold colored for identification.(Do not use with Perma-Seal™ or Type 410 SS TAPPER™)

Special Drill Bits for Type 304 SS Tapper™For use in hard aggregate concrete, tolerance = 0.220" to 0.222. Thisbit is silver colored for identification. (Do not use with Perma-Seal™or Type 410 SS TAPPER™)

Straight ShankPART USABLE STD.NO. SIZE LENGTH TUBE2894 3/16" x 3-1/2" 2" 102895 3/16" x 4-1/2" 3" 10

SDS HexPART USABLE STD.NO. SIZE LENGTH TUBE5866 1/4" x 6" 4" 15868 1/4" x 8" 6" 1

SDS HexPART USABLE STD.NO. SIZE LENGTH TUBE2790 3/16" x 5" 3" 1

SDS HexPART USABLE STD.NO. SIZE LENGTH TUBE2780 3/16" x 5" 3" 1

Carbide Drill Bits for 3/8" Zinc Plated Tapper™Straight Shank

PART USABLE STD.NO. SIZE LENGTH TUBE5861 1/4" x 5-1/2" 4" 55862 1/4" x 6-1/2" 5" 55863 1/4" x 7-1/2" 6" 5

PART MAX. SCREW MAX. BIT STD.NO. DESCRIPTION LENGTH LENGTH BOX2791 TAPPER™ 1000 Tool (as shown) 4" 5-1/2" 12792 CONDRIVE®† 2000 2-3/4" 4-1/2" 12795 1000 SDS Extension (8") 6" 7-1/2" 1

Tapper™ 1000 Replacement PartsPART STD.NO. DESCRIPTION BOX2953 Drive Sleeve Assy. (5-3/4") 12955* 1/8" Hex Key 12964 Blue 3/16” Hex Wedge-Bolt® Socket 1

PART STD.NO. DESCRIPTION BOX2956 1/4" Hex Key 12957 5/16" Hex Key 1

This tool cannot be used with SDS Drill Bits or PFH screws.

†CONDRIVE® is a Registered Trademark of Illinois Tool Works.


270SS 5/19/10 4:59 PM Page 270

271

Fasteners

Snake™Internally Threaded Self-Tapping AnchorBase MaterialConcrete

Size Range1/4" and 3/8" diameter

Anchor MaterialCarbon Steel

The snake anchor is an all-steel, self-tapping, machine bolt anchordesigned for use in concrete and is suitable for overhead applications.The anchor is installed with a power tool and mechanically interlockswith the base material. A hammer is not required for installation.A setting tool is packaged in each box.

Hollow-Set™ DropinInternally Threaded Expansion AnchorBase MaterialConcrete, Block, Brick, Pre-cast Hollow Core Plank, StoneSize Range1/4" to 5/8"Anchor MaterialZamac Alloy with Carbon Steel or Stainless Steel Cones

The Hollow-Set™ Dropin anchor is designed for anchoring in hollowbase materials such as hollow concrete block, brick with weep holesand hollow core pre-cast concrete plank. It can also be used in solidbase materials.Hollow masonry materials often have a minimum outer wall thicknessof 1-1/2". During the drilling process, spalling on the back side of thewall often decreases the wall thickness available for anchoring to 1" orless. The design of the Hollow-Set™ Dropin overcomes this problem.

Zamac Body with Carbon Steel Cone

PART MAX. SCREW MAX. BIT STD.NO. DESCRIPTION LENGTH LENGTH BOX5865 TAPPER™ 3000 Tool 4" 5-1/2" 15867 3000 Extension (8") 6" 7-1/2" 1

PART MIN. HOLE THREAD STD. STD.NO. SIZE DEPTH DEPTH BOX CTN.6400 1/4" 1-5/8" 1/4" 100 10006401 3/8" 1-7/8" 5/16" 50 500

PART STD. STD.NO. SIZE BOX CTN.6402 1/4" 1 2506403 3/8" 1 250

Installation Tools for 3/8" TAPPER™

PART STD.NO. DESCRIPTION BOX5874 Drive Sleeve Assembly (5-3/4") 15867 Drive Sleeve Assembly (8") 1

TAPPER™ 3000 Replacement Parts

PART DRILL OVERALL SLEEVE STD. STD.NO. SIZE DIA. LENGTH LENGTH BOX CTN.9320 1/4" 3/8" 7/8" 5/8" 100 10009330 5/16" 5/8" 1-5/16" 15/16" 50 5009340 3/8" 5/8" 1-5/16" 15/16" 50 5009350 1/2" 3/4" 1-3/4" 1-1/4" 50 250 9360 5/8" 1" 2" 1-1/2" 25 125

PART DRILL OVERALL SLEEVE STD. STD.NO. SIZE DIA. LENGTH LENGTH BOX CTN.9420 1/4" 3/8" 7/8" 5/8" 100 10009440 3/8" 5/8" 1-5/16" 15/16" 100 500

PART STD. STD.NO. SIZE BOX CTN.9322 1/4" 1 19342 5/16" & 3/8" 1 19352 1/2" 1 19362 5/8" 1 1

Extra Snake Setting Tools

Setting Tools — Solid Base Materials

Zamac Body with Stainless Steel Cone

Setting Tools — Hollow Base Materials

PART STD. STD.NO. SIZE BOX CTN.9323 1/4" 1 19333 5/16" 1 19343 3/8" 1 19353 1/2" 1 19363 5/8" 1 1

271SS 5/19/10 5:00 PM Page 271

272

Fasteners

Setting Tools for Steel Dropin Anchors

Use Setting Tool Part No. 6309 for 1/2" size, Part No. 6313 for 3/4" size.

Steel DropinInternally Threaded Expansion AnchorBase MaterialSolid Concrete, Solid Block, Hard Stone

Size Range1/4" to 3/4" Standard Thread, 1/2" & 3/4" in Coil Thread

Anchor MaterialCarbon Steel & Type 303 or 316 Stainless Steel

The Steel Dropin is an all-steel, machine bolt anchor available incarbon steel and two types of stainless steel. It can be used in solidconcrete, hard stone, and solid block. A coil-thread version forforming applications is also available. Mini Dropin

Internally Threaded Expansion AnchorBase MaterialPre-cast Hollow Core Plank, Concrete

Size Range1/4", 3/8", & 1/2"


The Mini Dropin is a carbon steel, machine bolt anchor used inshallow embedment applications. It can be used in solid concreteand hollow core concrete plank, it can be used in hard stone andsolid block. It may also be used in overhead applications.

PART DRILL MIN. THREAD STD. STD.NO. SIZE DIA. DEPTH DEPTH BOX CTN.6304 1/4" 3/8" 1" 7/16" 100 10006306 3/8" 1/2" 1-9/16" 5/8" 50 5006308 1/2" 5/8" 2" 13/16" 50 2506320 5/8" 7/8" 2-1/2" 1-3/16" 25 1256312 3/4" 1" 3-3/16" 1-3/8" 10 50

Carbon Steel Dropin (Smooth Wall)

PART DRILL MIN. THREAD STD. STD.NO. SIZE DIA. DEPTH DEPTH BOX CTN.6324 1/4" 3/8" 1" 7/16" 100 10006326 3/8" 1/2" 1-9/16" 5/8" 50 5006328 1/2" 5/8" 2" 13/16" 50 250

PART DRILL MIN. THREAD STD. STD.NO. SIZE DIA. DEPTH DEPTH BOX CTN.6335 1/4" 3/8" 5/8" 3/8" 100 10006322 3/8" 1/2" 3/4" 13/32" 100 10006337 1/2" 5/8" 1" 5/8" 50 250

Carbon Steel Flanged Dropin (Lipped)

PART ROD/ANCHOR OVERALL THREAD STD. STD.NO. SIZE LENGTH DEPTH BOX CTN.6340 1/4" 1" 7/16" 100 10006342 3/8" 1-9/16" 5/8" 50 2506344 1/2" 2" 13/16" 50 250

Carbon Steel Knurled Wall Dropin


PART STD. STD.NO. SIZE BOX CTN.6305 1/4" 1 2506307 3/8" 1 1006309 1/2" 1 1006311 5/8" 1 506313 3/4" 1 25

Type 303 Stainless Steel Dropin


Type 316 Stainless Steel Dropin

PART DRILL MIN. THREAD STD. STD.NO. SIZE DIA. DEPTH DEPTH BOX CTN.6330 1/2" 5/8" 2" 13/16" 50 2506332 3/4" 1" 3-3/16" 1-3/8" 10 50

Carbon Steel Coil Thread Dropin

Setting ToolsPART STD. STD.NO. SIZE BOX CTN.6336 1/4" 1 506323 3/8" 1 506338 1/2" 1 50

Double™ Expansion AnchorShell Expansion AnchorBase MaterialConcrete, Block, Brick

Size Range1/4" to 3/4"

Anchor MaterialZamac Alloy

The Double™ is a dual expansion machine bolt anchor particularlysuited for materials of questionable strength. It can be used in solidconcrete and some block, brick and stone base materials.

272SS 5/19/10 5:00 PM Page 272

273

Fasteners

Calk-In™ tools purchased separately (not included).

Lag Shield™Shell Expansion AnchorBase MaterialConcrete and Mortar Joints of Block and Brick

Size Range1/4" to 3/4"

Anchor MaterialZamac Alloy

The Lag Shield™ is a screw style anchor designed for use with lagbolts. It is suitable for use in concrete and the mortar joints of blockor brick walls. Lag Shield™ anchors are formed from Zamac alloy. Inharder masonry materials, short style Lag Shields are used to reducedrilling time. The long style version is used in soft or weak masonryto better develop strength.

PART ANCHOR DRILL MIN. HOLE STD. STD.NO. SIZE LENGTH DIA. DEPTH BOX CTN.9510 1/4" 1-3/8" 1/2" 1-1/4" 50 5009515 5/16" 1-5/8" 5/8" 1-1/2" 50 5009520 3/8" 2" 3/4" 1-3/4" 50 2509525 1/2" 2-1/2" 7/8" 2-1/4" 25 2509530 5/8" 2-3/4" 1" 2-1/2" 25 1009535 3/4" 3-15/16" 1-1/4" 3-1/2" 10 50

PART ANCHOR DRILL MIN. HOLE STD. STD.NO. SIZE LENGTH DIA. DEPTH BOX CTN.9650 1/4" 1-5/16" 1/2" 1-3/8" 50 2509655 5/16" 1-1/2" 5/8" 1-5/8" 50 2509665 3/8" 1-1/2" 5/8" 1-5/8" 50 2509675 1/2" 2-1/16" 7/8" 2-1/2" 25 1259685 5/8" 2-5/8" 1" 2-3/4" 25 125

PART DRILL MIN. STD. STD.NO. SIZE DIA. EMBED. BOX CTN.1051 1/4" Short 1/2" 1" 50 5001055 1/4" Long 1/2" 1-1/2" 50 5001101 5/16" Short 1/2" 1-1/4" 50 5001105 5/16" Long 1/2" 1-3/4" 50 5001151 3/8" Short 5/8" 1-3/4" 50 5001155 3/8" Long 5/8" 2-1/2" 50 2501201 1/2" Short 3/4" 2" 50 5001205 1/2" Long 3/4" 3" 50 2001251 5/8" Short 7/8" 2" 25 1251255 5/8" Long 7/8" 3-1/2" 25 1251301 3/4" Short 1" 2" 25 1251305 3/4" Long 1" 3-1/2" 25 100

Setting ToolsPART STD. STD.NO. SIZE BOX CTN.9201* 8 1 19211 10 1 19221 1/4" 1 19226 5/16" 1 19231 3/8" 1 19241 1/2" 1 1

Single™ Expansion AnchorShell Expansion AnchorBase MaterialConcreteSize Range1/4" to 5/8"Anchor MaterialZamac Alloy

The Single™ is a machine bolt anchor designed for use in concrete,and some block, brick and stone base materials. The anchor consistsof a pre-assembled set of expansion shields and an expander coneformed from Zamac alloy.

PART DRILL MIN. STD. STD.NO. SIZE DIA. DEPTH BOX CTN.9205 8–32 5/16" 1/2" 100 10009210 10–24 3/8" 5/8" 100 10009220 1/4"–20 1/2" 7/8" 100 10009225 5/16"–18 5/8" 1" 50 2509230 3/8"–16 3/4" 1-1/4" 50 2509240 1/2"–13 7/8" 1-1/2" 50 250

Calk-In™Machine Screw AnchorBase MaterialConcrete, Block, BrickSize Range8–32 to 1/2"–13Anchor MaterialZamac Alloy and Lead

The Calk-In™ is a pre-assembled precision cast calking type machinebolt anchor which can be used in concrete, block, brick or stone. Theanchor consists of an antimonial lead alloy calking sleeve and aZamac alloy internally-threaded expander cone.

PART DRILL MIN. MASTERNO. SIZE DIA. DEPTH CTN.9222* 1/4"–20 1/2" 7/8" 1000

Master Pack



273SS 5/19/10 5:00 PM Page 273

274

Fasteners

Mushroom Head Grade 8.2 Carbon Steel Spike®

PART DRILL MIN. STD. STD. NO. SIZE DIA. EMBED. BOX CTN.5502 3/16" x 1" 3/16" 7/8" 100 10005503 3/16" x 1-1/4" 3/16" 7/8" 100 10005504 3/16" x 1-1/2" 3/16" 1-1/4" 100 10005506 3/16" x 2" 3/16" 1-1/4" 100 10005508 3/16" x 2-1/2" 3/16" 1-1/4" 100 10005510 3/16" x 3" 3/16" 1-1/4" 100 10005511 3/16" x 3-1/2" 3/16" 1-1/4" 100 10005512 3/16" x 4" 3/16" 1-1/4" 100 5005522 1/4" x 1" 1/4" 7/8" 100 10005523 1/4" x 1-1/4" 1/4" 1" 100 10005524 1/4" x 1-1/2" 1/4" 1-1/4" 100 10005526 1/4" x 2" 1/4" 1-1/4" 100 10005528 1/4" x 2-1/2" 1/4" 1-1/4" 100 10005530 1/4" x 3" 1/4" 1-1/4" 100 10005531 1/4" x 3-1/2" 1/4" 1-1/4" 100 10005532 1/4" x 4" 1/4" 1-1/4" 100 5005546 3/8" x 2" 3/8" 1-3/4" 25 2505548 3/8" x 2-1/2" 3/8" 1-3/4" 25 2505550 3/8" x 3" 3/8" 1-3/4" 25 2505551 3/8" x 3-1/2" 3/8" 1-3/4" 25 2505552 3/8" x 4" 3/8" 1-3/4" 25 2505554 3/8" x 5" 3/8" 1-3/4" 25 2505556 3/8" x 6" 3/8" 1-3/4" 25 2505569 1/2" x 2-3/4" 1/2" 2-1/2" 50 2005571 1/2" x 3-1/2" 1/2" 2-1/2" 50 1505572 1/2" x 4" 1/2" 2-1/2" 25 1505574 1/2" x 5" 1/2" 2-1/2" 25 1505577 1/2" x 6-1/2" 1/2" 2-1/2" 25 150

The published length is measured from below the head to the end of the anchor.

Flat Head Grade 8.2 Carbon Steel Spike®

PART DRILL MIN. STD. STD. NO. SIZE DIA. EMBED. BOX CTN.5608 3/16" x 2-1/2" 3/16" 1-1/4" 100 10005610 3/16" x 3" 3/16" 1-1/4" 100 10005612 3/16" x 4" 3/16" 1-1/4" 100 10005624 1/4" x 1-1/2" 1/4" 1-1/4" 100 10005626 1/4" x 2" 1/4" 1-1/4" 100 10005628 1/4" x 2-1/2" 1/4" 1-1/4" 100 10005630 1/4" x 3" 1/4" 1-1/4" 100 10005631 1/4" x 3-1/2" 1/4" 1-1/4" 100 10005632 1/4" x 4" 1/4" 1-1/4" 100 500

The published length is the overall length of the anchor.

Mushroom Head Type 316 Stainless Steel Spike®

Special Application Spike Anchor

PART DRILL MIN. STD. STD. NO. SIZE DIA. EMBED. BOX CTN.6602 3/16" x 1" 3/16" 7/8" 100 10006603 3/16" x 1-1/4" 3/16" 7/8" 100 10006604 3/16" x 1-1/2" 3/16" 1-1/4" 100 10006606 3/16" x 2" 3/16" 1-1/4" 100 10006623 1/4" x 1-1/4" 1/4" 1" 100 10006624 1/4" x 1-1/2" 1/4" 1-1/4" 100 10006626 1/4" x 2" 1/4" 1-1/4" 100 10006628 1/4" x 2-1/2" 1/4" 1-1/4" 100 10006630 1/4" x 3" 1/4" 1-1/4" 100 10006646 3/8" x 2" 3/8" 1-3/4" 25 2506648 3/8" x 2-1/2" 3/8" 1-3/4" 25 2506650 3/8" x 3" 3/8" 1-3/4" 25 250

Rod HangingPipe Spike®

Grade 8.2 Carbon SteelPART HEAD DRILL MIN. STD. STD. NO. SIZE DIA. EMBED. BOX CTN.3755 1/4" 3/16" 1-1/4" 100 10003758 3/8" 1/4" 1-3/4" 50 500

Concrete FormingForming Spike® Grade 8.2 Carbon Steel

Spike® Installation ToolsWhile the SPIKE® anchor can easily be installed using a hammer, aspecially designed series of drivers and manual tools provide a fast,easy to use method for installing SPIKE® anchors into concrete andmasonry materials. The tools allow SPIKE® anchors to be installedin confined areas and prevent damage to the fixture from strayhammer blows.

PART ANCHOR DRILL MIN. STD. STD. NO. SIZE DIA. EMBED. BOX CTN.3795 3/16" x 1-1/2" 3/16" 1-1/4" 100 10003796 3/16" x 2" 3/16" 1-1/4" 100 10003797 3/16" x 2-3/4" 3/16" 1-1/4" 100 10003794 1/4" x 2-3/4" 1/4" 1-1/4" 100 1000

Suspended CeilingsTie-Wire Spike®

Grade 8.2 Carbon SteelPART DRILL MIN. TIE-WIRE STD. STD. NO. SIZE DIA. EMBED. HOLE SIZE BOX CTN.3756 3/16" 3/16" 1-1/4" 3/16" 100 5003759 1/4" 1/4" 1-1/4" 9/32" 100 500

The published length is measured from below the head to the end of the anchor.† Supplied with EPDM Sealing Washer.

274SS 5/19/10 5:00 PM Page 274

275

Fasteners

PART TOOL GUIDE STD. NO. DESCRIPTION I.D. BOX3790 SPIKE® Driver 1000 1/2" 13791 SPIKE® Driver 2000 1/2" 1

Spike® Installation Tools (cont.)

PART TOOL TIP STD. NO. DESCRIPTION O.D. BOX3760 Pipe SPIKE® Setting Tool 5/16" 1

Pipe Spike® Tool

PART DRILL MIN. STD. STD.NO. SIZE DIA. DEPTH BOX CTN.3031* 3/16" x 1" 3/16" 7/8" 100 10003091 3/16" x 1-1/2" 3/16" 7/8" 100 10003211 1/4" x 1-1/4" 1/4" 1-1/8" 100 10003241 1/4" x 1-1/2" 1/4" 1-1/8" 100 10003271 1/4" x 2" 1/4" 1-1/8" 100 10003301 1/4" x 2-1/2" 1/4" 1-1/8" 100 10003601 3/8" x 2" 3/8" 1-7/8" 25 2503631 3/8" x 2-1/2" 3/8" 1-7/8" 25 2503691 3/8" x 3-1/2" 3/8" 1-7/8" 25 2503781 1/2" x 3" 1/2" 2-5/8" 25 125

Round Head Drive® PART DRILL STD. STD.NO. SIZE DIA. BOX CTN.2848 1/4" x 2-1/4" 1/4" 100 5002850 1/4" x 3" 1/4" 100 5002839 1/4" x 3/4" 1/4" 100 5002840 1/4" x 1" 1/4" 100 5002842 1/4" x 1-1/4" 1/4" 100 5002844 1/4" x 1-1/2" 1/4" 100 5002846 1/4" x 2" 1/4" 100 500

Zamac Hammer-Screw® Anchor Mushroom Head with No. 2 Phillips Type Screw Carbon Steel

PART DRILL STD. STD.NO. SIZE DIA. BOX CTN.2939 1/4" x 3/4" 1/4" 1000 10002940 1/4" x 1" 1/4" 1000 10002942 1/4" x 1-1/4" 1/4" 1000 10002944 1/4" x 1-1/2" 1/4" 1000 10002946 1/4" x 2" 1/4" 1000 10002948 1/4" x 2-1/4" 1/4" 1000 10002949 1/4" x 3" 1/4" 1000 1000

MASTER PACK WITH CARBON STEEL SCREW

PART DRILL STD. STD.NO. SIZE DIA. BOX CTN.2817 1/4" x 1-1/4" 1/4" 100 500

Zamac Hammer-Screw® Anchor Mushroom Head with No. 2 Phillips Type Perma-Seal Screw

PART DRILL STD. STD.NO. SIZE DIA. BOX CTN.2818 1/4" x 1-1/4" 1/4" 1000 1000

MASTER PACK

PART DRILL MIN. STD. STD.NO. SIZE DIA. DEPTH BOX CTN.3092 3/16" x 1-1/2" 3/16" 7/8" 100 10003122 3/16" x 2" 3/16" 7/8" 100 10003152 3/16" x 2-1/2" 3/16" 7/8" 100 10003162 3/16" x 3" 3/16" 7/8" 100 10003242 1/4" x 1-1/2" 1/4" 1-1/8" 100 10003272 1/4" x 2" 1/4" 1-1/8" 100 10003302 1/4" x 2-1/2" 1/4" 1-1/8" 100 10003332 1/4" x 3" 1/4" 1-1/8" 100 10003362 1/4" x 3-1/2" 1/4" 1-1/8" 100 10003392 1/4" x 4" 1/4" 1-1/8" 100 500

Flat Head Drive®

PART DRILL MIN. STD. STD.NO. SIZE DIA. DEPTH BOX CTN.3244 1/4" x 1-3/4" 1/4" 1-1/8" 500 5003245 1/4" x 1-3/4" 1/4" 1-1/8" 100 5003250 Tie-Wire Setting Tool 1 1

Tie-Wire Drive®

(13/64" Tie-Wire Hole)

Drive®

Split Pin Type Pre-Expander AnchorBase MaterialConcreteSize Range3/16" x 1" to 1/2" x 3"Anchor MaterialCarbon Steel The Drive® is a one piece tamper-proof, pre-expanded anchor available incarbon steel for use in concrete and stone. Tie-Wire Drive® anchors are used forsuspended ceiling applications. The flat head (counter-sunk) style is particularlysuited for wood-to-concrete anchoring. The round head style is for all otherapplications requiring fast, permanent installations.

Zamac Hammer-Screw®

Nail AnchorBase MaterialConcrete, Block, Brick, StoneSize Range1/4" x 3/4" to 1/4" x 3"Anchor MaterialZamac Alloy with Carbon Steel and Perma-Seal Drive ScrewThe Zamac Hammer-Screw® is a unique, one-step drive anchor featuring aPhillips type head and a screw thread for use in concrete, block, brick or stone.The anchor has a body formed from corrosion resistant Zamac alloy with acarbon or stainless steel drive screw, and has been developed as animprovement over standard nailin anchors. The anchor is removable, has 40%higher tension load capacities when installed in concrete, and can be usedoverhead provided it is part of an engineered system designed by an engineerwho will take the proper design considerations and safety factors into account.


275SS 5/19/10 5:01 PM Page 275

276

Fasteners

PART DRILL STD. STD.NO. SIZE DIA. BOX CTN.2802 3/16" x 7/8" 3/16" 100 5002806 1/4" x 3/4" 1/4" 100 5002808 1/4" x 1" 1/4" 100 5002814 1/4" x 1-1/4" 1/4" 100 5002820 1/4" x 1-1/2" 1/4" 100 5002826 1/4" x 2" 1/4" 100 5002804 1/4" x 3" 1/4" 100 500

Mushroom Head Zamac Nailin® — Carbon Steel Nail

PART DRILL STD. STD.NO. SIZE DIA. BOX CTN.2431 3/16" x 1" 3/16" 100 10002451 3/16" x 1-1/2" 3/16" 100 10002521 1/4" x 1" 1/4" 100 10002541 1/4" x 1-1/2" 1/4" 100 1000

Round Head Nylon Nailin® — Carbon Steel Nail

Zamac Nailin®

Drive Pin Type AnchorBase MaterialConcrete, Block, Brick, Stone

Size Range3/16" x 7/8" to 1/4" x 2"

Anchor MaterialZamac Alloy with Carbon or Stainless Steel Drive PinThe Zamac Nailin® is a tamper-proof nail drive anchor which has a bodyformed from Zamac alloy. Nails are available in carbon or stainless steel.The anchor can be used in concrete, block, brick or stone. This anchor isnot recommended for applications overhead.

Nylon Nailin®

Plastic Drive Pin Type AnchorBase MaterialConcrete, Block, Brick,

Size Range3/16" x 1" to 1/4" x 6"

Anchor MaterialEngineered Nylon with Carbon or Stainless Steel Drive PinThe Nylon Nailin® is a pin drive anchor with a body formed fromengineered nylon and nails available in carbon and stainless steel. Theanchor can be used in concrete, block, or brick. This anchor is notrecommended for applications overhead.

PART DRILL STD. STD.NO. SIZE DIA. BOX CTN.2542 1/4" x 1-1/2" 1/4" 100 10002562 1/4" x 2" 1/4" 100 1000

Flat Head Nylon Nailin® — Carbon Steel Nail

PART DRILL STD. STD.NO. SIZE DIA. BOX CTN.2433 3/16" x 1" 3/16" 100 10002513 1/4" x 3/4" 1/4" 100 10002523 1/4" x 1" 1/4" 100 10002543 1/4" x 1-1/2" 1/4" 100 10002563 1/4" x 2" 1/4" 100 10002573 1/4" x 3" 1/4" 100 10002583 1/4" x 4" 1/4" 100 10002593 1/4" x 6" 1/4" 100 400

Mushroom Head Nylon Nailin® — Carbon Steel Nail

PART DRILL STD. STD.NO. SIZE DIA. BOX CTN.2836 1/4" x 1-1/2" 1/4" 100 5002838 1/4" x 2" 1/4" 100 500

Flat Head Zamac Nailin® — Carbon Steel Nail

PART DRILL STD. STD.NO. SIZE DIA. BOX CTN.2528 1/4" x 1" 1/4" 100 10002548 1/4" x 1-1/2" 1/4" 100 1000

Mushroom Head Nylon Nailin® Stainless Steel Nail

PART DRILL STD. STD.NO. SIZE DIA. BOX CTN.2574 1/4" x 3" 1/4" 2500 2500

Mushroom Head Bodies Only

PART DRILL STD. STD.NO. SIZE DIA. BOX CTN.2858 1/4" x 1" 1/4" 100 5002864 1/4" x 1-1/4" 1/4" 100 5002870 1/4" x 1-1/2" 1/4" 100 5002876 1/4" x 2" 1/4" 100 500

Mushroom Head Zamac Nailin®

Type 304 Stainless Steel Nail

PART DRILL STD. STD.NO. SIZE DIA. BOX CTN.2803 3/16" x 7/8" 3/16" 1000 10002807 1/4" x 3/4" 1/4" 1000 10002809 1/4" x 1" 1/4" 1000 10002815 1/4" x 1-1/4" 1/4" 1000 10002821 1/4" x 1-1/2" 1/4" 1000 10002827 1/4" x 2" 1/4" 1000 10002805 1/4" x 3" 1/4" 1000 1000

MASTER PACK

276SS 5/19/10 5:01 PM Page 276

277

Fasteners

INJECTION GLASS CAPSULEADHESIVE ADHESIVE ANCHOR BONDING

ANCHOR CATEGORY ANCHORS ANCHORS HARDWARE EXPANSION FOAM SEALANT

PRODUCT

Adhesive Selection Guide

■ Suitable■■ May Be Suitable

AC10

0 PL

US

Chem

istry

Anch

orEl

emen

tW

orki

ngLo

ad

POW

ER-F

AST+

CHEM

-STU

D

HAM

MER

-CAP

SULE

STRA

IGHT

CUT

ANCH

OR R

OD

CHIS

EL P

OINT

EDAN

CHOR

ROD

NTER

NALL

YTH

READ

ED IN

SERT

S

POW

ERFO

AM

TRIG

GERF

OAM

POW

ERST

ICK

Concrete ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

Lightweight Concrete ■ ■ ■■ ■■ ■ ■■ ■■ ■ ■ ■

Grout-filled Concrete Masonry ■ ■ ■■ ■■ ■ ■■ ■■ ■ ■ ■

Hollow Concrete Masonry ■ ■ ■ ■ ■ ■

Solid Brick ■ ■ ■■ ■■ ■ ■■ ■■ ■ ■ ■

Hollow Brick ■■ ■ ■ ■ ■ ■

Stone ■■ ■■ ■■ ■■ ■ ■■ ■■ ■ ■ ■

Structural Clay Tile ■■ ■■ ■ ■ ■ ■

1/4" ■■ ■ ■

3/8" ■ ■ ■ ■ ■ ■ ■

1/2" ■ ■ ■ ■ ■ ■ ■

5/8" ■ ■ ■ ■ ■ ■ ■

3/4" ■ ■ ■ ■ ■ ■ ■

7/8" ■ ■ ■ ■ ■ ■

1" ■ ■ ■ ■ ■ ■

1 1/4" ■ ■ ■ ■■ ■ ■

1 3/8" ■■ ■

1 1/2" ■■ ■

1 3/4" ■■ ■■

2" ■■ ■■

Under 400 lbs. ■ ■ ■ ■ ■ ■ ■

400 lbs. to 4,000 lbs. ■ ■ ■ ■ ■ ■ ■

Over 4,000 lbs. ■ ■ ■ ■ ■ ■ ■

Coated / Plated Carbon Steel ■ ■ ■

Type 304 Stainless Steel ■ ■

Epoxy ■

Ester Based Resin ■ ■ ■

Polyurethane ■ ■

MS Polymer ■

Anch

or D

iam

eter

Base

Mat

eria

l

277SS 5/19/10 5:01 PM Page 277

278

Fasteners

AC100PLUS™

Epoxy Acrylate Adhesive Anchoring SystemProduct DescriptionAC100 Plus Epoxy Acrylate is a two-component, high strengthstructural adhesive used to bond threaded rod and reinforcing barinto solid concrete and masonry base materials. The adhesive systemcan also be used to anchor into hollow masonry materials usingscreen tubes. The AC100 Plus adhesive is a 100% solids, low odor,moisture insensitive formulation. The proprietary characteristicsinclude the first formulation on the market that does not containvolatile organic compounds (VOC’s) and is free of styrene andsolvents.The AC100 Plus adhesive is packaged in cartridges made fromengineered plastic which are used with either a manual orpneumatically operated injection tool. The two-component adhesivechemistry is mixed and applied through a static mixing nozzle toprovide an anchoring system that is consistent, cost effective andefficient.

Free nozzle with every 5.5, 8, 10 and 12 oz. Cartridge

AC100 Plus CartridgesPART STD. STD.NO. DESCRIPTION BOX CTN.8462 5.5 oz. Pusher Cartridge 12 368480 8 oz. Cartridge 1 128478 10 oz. Quik-Shot Cartridge 12 368486 12 oz. Cartridge 1 128490 30 oz. Jumbo Cartridge 1 8

Cartridge System NozzlePART STD. STD.NO. DESCRIPTION BOX CTN.8482 Extra nozzle for 10, 8 & 12 oz. AC100 Plus 12 144

(8480, 8486, 8478) 8498 Extra nozzle for 30 oz. AC100 Plus (8490) 24 24

8437 8484 8494

8485 8495

AC100 Plus Manual Delivery SystemPART STD. STD.NO. DESCRIPTION BOX CTN.8437 10 oz. Heavy Duty Caulking Gun (8462, 8478) 1 128463 10 oz. High Performance Caulking Gun (8478) 1 68484 8 oz. std. all Metal Manual Tool (8480) 1 68494 30 oz. std. all Metal Manual Tool (8490, 8491) 1 18485 8 & 12 oz. High Performance Manual Tool 1 20

(8480, 8486)8495 30 oz. High Performance Manual Tool (8490, 8491) 1 1

Pneumatic Injection Tool Delivery SystemPART STD. STD.NO. DESCRIPTION BOX CTN.8496 30 oz. High Performance Pneumatic Tool 1 1

Battery Injection Dispensing ToolPART STD. STD.NO. DESCRIPTION BOX CTN.8444 30 oz. High Performance Battery Tool 1 1

278SS 5/19/10 5:02 PM Page 278

279

Fasteners

Power-Fast®+ Epoxy AdhesiveEpoxy Adhesive Anchoring SystemProduct DescriptionThe Power-Fast+ Epoxy Adhesive is a two component structuralepoxy which is packaged in specially designed cartridges made froman engineered plastic which are used with either a manual orpneumatically operated injection tool. The epoxy used is an odorless,premium, high strength epoxy which has a proven track record. Power-Fast+ Epoxy is designed for use in anchoring threaded rods,bolts, reinforcing bars, and smooth dowels into concrete and othersolid base materials. The system can also be used to anchor intohollow masonry materials using threaded rods and screen tubes. Inaddition to anchoring applications, Power-Fast+ is occasionally usedfor bonding steel and cured concrete to cured concrete, for pickproofing applications, for surface sealing cracks, and for placinginjection ports.

Power-Fast+ CartridgesPART STD. STD.NO. DESCRIPTION BOX CTN.8424 10 oz. Quik-Shot Cartridge — Fast Set 12 368402 15 oz. Cartridge — Fast Set 12 128422 22 oz. Cartridge — Fast Set 12 128403 15 oz. Cartridge — Standard Set 12 128423 22 oz. Cartridge — Standard Set 12 128443 44 oz. Jumbo Cartridge — Standard Set 6 68436 56 oz. Jumbo Cartridge — Standard Set 6 6

FREE nozzle with every 10, 15 and 22 oz. Cartridge

Battery Injection Dispensing ToolsPART STD. STD.NO. DESCRIPTION BOX CTN.8442 22 oz. High Performance Battery Tool 1 1

Cartridge System NozzlePART STD. STD.NO. DESCRIPTION BOX CTN.7908 Extra Nozzle for Power-Fast+ 2 247919 Extra Nozzle for Power-Fast+ Master Pack 400 4007921 Extra Nozzle for 44 & 56 oz.

Power-Fast+ (8443 & 8436) 12 12

8437 8415

8421

8416 8409

Power-Fast + Manual Delivery SystemPART STD. STD.NO. DESCRIPTION BOX CTN.8437 10 oz. Quick-Shot Heavy Duty Caulking Gun 1 128463 10 oz. Quick-Shot High Performance Caulking Gun 1 18415 15 oz. High Performance Manual Tool 1 108421 22 oz. High Performance Manual Tool 1 68416 15 oz. Standard all metal Manual Tool 1 88409 22 oz. Standard all metal Manual Tool 1 8

Pneumatic Injection Tool Delivery SystemPneumatic injection tools are designed for large jobs. The maincylinder is formed using top quality aluminum to provide alightweight, durable tool. The dispensing trigger is designed toprovide instant pressure relief from the cartridge which reduceswaste. The tool also has a reverse button feature for fast and easyremoval of cartridges during use.

PART STD. STD.NO. DESCRIPTION BOX CTN.8413 22 oz. High Performance Pneumatic Tool 1 18445 44 oz. High Performance Pneumatic Tool 1 18438 56 oz. High Performance Pneumatic Tool 1 1

279SS 5/19/10 5:02 PM Page 279

280

Fasteners

PART *DRILL MIN. STD. STD.NO. SIZE DIA. DEPTH BOX CTN.6502 3/8" 7/16" 3-1/2" 10 5006503 1/2" 9/16" 4-1/4" 10 2006504 5/8" 11/16" 5" 10 2006505 3/4" 7/8" 6-5/8" 5 506506 7/8" 1" 7" 5 506507 1" 1-1/8" 8-1/4" 5 506508 1-1/4" 1-1/2" 10-1/4" 5 25

Chem-Stud®

Spin-In Type Capsule AdhesiveProduct DescriptionThe Chem-Stud Anchor System consists of self contained two-part glasscapsules and matching chisel pointed anchor rods which are installed usinga rotary hammer drill and rod adapters. The Chem-Stud adhesive is an esterbased resin material packaged in a single use glass capsules designed forinstallation of 3/8" through 1-1/2" threaded rods in solid concrete andmasonry materials. It can also be used for reinforcing bars.

Chem-Stud Selection GuideChem-Stud Capsules

PART STD. STD.NO. SIZE BOX CTN.6562 3/8" 1 106563 1/2" 1 106564 5/8" 1 106565 3/4" 1 56566 7/8" 1 56567 1" 1 56568 1-1/4" 1 5

Chem-Stud Installation ToolsChem-Stud installation tools consist of a drive adapter which isdesigned to fit the rotary hammer drill used and a coupler to holdeither threaded rods or reinforcing bars. The tools for threaded rodand reinforcing bars are different and can not be interchanged

Threaded Rod Installation ToolsCouplers for Threaded Rod

PART HEX FITS COUPLER STD. STD.NO. SIZE SIZE BOX CTN.6570 1/4" 3/8" to 5/8" 1 106572 3/8" 3/4" to 1-1/4" 1 10

Drivers for Threaded Rod Couplers — Hex


Drivers for Threaded Rod Couplers — SDS-plus


Drivers for Threaded Rod Couplers — SDS-MAX


Drivers for Threaded Rod Couplers — SPLINE

PART DRILL MIN. STD. STD.NO. SIZE DIA. DEPTH BOX CTN.6513 1/2" x 6-1/2" 9/16" 4-1/4" 10 506514 5/8" x 7-1/2" 11/16" 5" 10 406515 3/4" x 9-5/8" 7/8" 6-5/8" 10 406517 1" x 12" 1-1/8" 8-1/4" 10 106518 1-1/4" x 15 1-1/2" 10-1/4" 5 5

Chem-Stud Chisel-Pointed Anchor RodsCarbon steel rods are zinc plated according to ASTM B 633, SC1. A supplemental coating is applied over the zinc. For A307 anchor rod, a Type III clear chromate treatment is applied. B7 anchor rod has a Type IIyellow dichromate coating.

A307 Standard Carbon Steel, Zinc Plated (ASTM B 633)

PART DRILL MIN. STD. STD.NO. SIZE DIA. DEPTH BOX CTN.6523* 1/2" x 6-1/2" 9/16" 4-1/4" 10 506524* 5/8" x 7-1/2" 11/16" 5" 10 406525* 3/4" x 9-5/8" 7/8" 6-5/8" 10 406528* 1-1/4" x 15 1-1/2" 10-1/4" — 5

ASTM A193 Grade B7 High-Strength Carbon, Zinc Plated (ASTM B 633 Yellow Dichromate)B7 (AISI 4140) anchor rod is supplied with nuts meeting the require-ments of ASTM Specification A 194, Grade 2H (ASTM A 563, Grade DH)and hardened washers meeting the requirements of ASTM F 436.


PART DRILL MIN. THRD. STD. STD. STD. STD.NO. SIZE O.D. DIA. DEPTH LENGTH BOX CTN.6592* 3/8" x 3-1/2" 0.55" 5/8" 3-1/2" 1-1/2" 10 506593* 1/2" x 4-1/4" 0.65" 11/16" 4-1/4" 1-5/8" 10 506594* 5/8" x 5" 0.90" 1" 5" 2-3/8" 10 40

Carbon Steel Internally Threaded Inserts


280SS 5/19/10 5:03 PM Page 280

281

Fasteners

PART STD. STD.NO. SIZE BOX CTN.6533 #3 Coupler 1 106534 #4 Coupler 1 56536 #6 Coupler 1 106537 #7 Coupler 1 106538 #8 Coupler 1 106539 #9 Coupler 1 106540 #10 Coupler 1 16589* Skil Driver Extension 1 16590 Spline Driver Extension 1 16596 SDS-Max Driver Extension 1 1

Chem-Stud Rebar Couplers and Drivers

Reinforcing Bar Installation Tools


PART STD. STD.NO. SIZE BOX CTN.6862 3/8" 1 16863 1/2" 1 16864 5/8" 1 16865 3/4" 1 1

Internally Threaded Insert Tools*

*Use with drivers for threaded rod.

Hammer-Capsule®

Drive-In Type Capsule Adhesive

Product DescriptionThe Hammer-Capsule System consists of a self contained, single use,two-part glass capsule into which threaded anchor rod or reinforcingbars can be directly driven without the need for a chisel point orspinning action. It is designed for use in the installation of 3/8" through1" diameter threaded rod in solid concrete and masonry materials. Itcan also be used to install reinforcing bars.

PART *DRILL MIN. STD. STD.NO. SIZE DIA. DEPTH BOX CTN.6702 3/8" 7/16" 3-1/2" 10 5006703 1/2" 9/16" 4-1/4" 10 2006704 5/8" 11/16" 5" 10 1006705 3/4" 7/8" 6" 5 506706 7/8" 1" 7" 5 506707 1" 1-1/8" 8-1/4" 5 50

Hammer-Capsule Selection Guide

Adhesive Installation Accessories, Anchor SealPlugs, Screen Tubes and Threaded Anchor RodsAdhesive installation accessories are designed to provide a dispenseror mixing nozzle extension when required and to aid in the preparationof the anchor hole.

PART STD.NO. DESCRIPTION BAG7914 Extension Tubing (25 feet) 17930* Blow Out Bulb 17931 1/2" x 8-1/2" brush 17932 3/4" x 8-1/2" brush 17933 1" x 12" brush 17934 1-1/4" x 13" brush 17935 1-1/2" x 16" brush 1

* Blow out bulbs typically do not create enough air pressure to properly cleanmost larger diameter and deeper embedment depth anchor holes. They are onlyappropriate for smaller diameter anchors with shallow embedment depths.

Anchor Seal PlugsAnchor seal plugs are designed for use with anchor installations inceilings and wall applications. The plugs help retain the adhesive in theanchor hole and hold the anchor rod centered in the hole until theadhesive sets. The plugs are described by the anchor rod diameterthey are used with.

PART PLUG HOLE STD.NO. DESCRIPTION DEPTH SIZE BAG7936 3/8" Anchor Seal Plug 3/8" 7/16" 257937 1/2" Anchor Seal Plug 1/2" 9/16" 25

How about

extra blades

for that saw?

281SS 5/19/10 5:03 PM Page 281

282

Fasteners

Straight Cut Threaded Rod Straight cut rod is provided in the materials listed below and includes nuts and washers.

PART STD.NO. DESCRIPTION CTN.7980 1/4" x 3 Anchor Rod 257985 1/2" x 5-1/2" Anchor Rod 257986 1/2" x 8" Anchor Rod 257989 5/8" x 6-1/2" Anchor Rod 207990 5/8" x 8" Anchor Rod 207946* 5/8" x 19" Anchor Rod 207947* 5/8" x 21" Anchor Rod 207993 3/4" x 9" Anchor Rod 107994 3/4" x 12" Anchor Rod 10


A307 Threaded Anchor Rod, Zinc Plated (ASTM B 633, Clear Chromate)

PART STD. STD.NO. DESCRIPTION BOX CTN.6026* 7/8" x 10-1/4" Anchor Rod 10 406027* 1" x 12" Anchor Rod 10 406028* 1-1/4" x 15" Anchor Rod 15 5


B7 High Strength Anchor Rod, Zinc Plated(ASTM B 633, Yellow Dichromate)B7 (AISI 4140) anchor rod (ASTM A 193) is supplied with nutsmeeting the requirements of ASTM Specification A 194, Grade 2H(ASTM A 563, Grade DH) and hardened washers meeting therequirements of ASTM F 436.

PART STD.NO. DESCRIPTION CTN.7957* 3/4" x 21" 22-1/2° Bent Rod 10


Bent Threaded Rod (22-1/2°)Rod is pre-bent at a 22-1/2 degree angle and includes nuts andwashers.

Plastic Screen TubesThe nominal diameter of the screen listed indicate the matching roddiameter. Note that hole size required for plastic screen tubes aredifferent than that for the stainless steel tubes.

PART DRILL STD.NO. DESCRIPTION DIA. CTN.8470 1/4" x 1-3/4" Screen Tube 1/2" 258473 3/8" x 2-3/4" Screen Tube 9/16" 258474 3/8" x 3-1/2" Screen Tube 9/16" 258475 1/2" x 3-1/4" Screen Tube 5/8" 258476 1/2"x 4" Screen Tube 5/8" 25

*Discontinued item once current stock exhausted.† Includes extension tubing

Stainless Steel Screen Tubes Screen tubes are made from a 300 series stainless steel. The nominaldiameter of the screen listed indicates the matching rod diameter.

PART DRILL STD.NO. DESCRIPTION DIA. CTN.7960* 1/4" x 2" Screen Tube † 3/8" 257862 1/4" x 6" Screen Tube † 3/8" 257864 1/4" x 8" Screen Tube † 3/8" 257866* 1/4" x 10" Screen Tube † 3/8" 257961 3/8" x 3-1/2" Screen Tube † 1/2" 257962 3/8" x 6" Screen Tube † 1/2" 257963 3/8" x 8" Screen Tube † 1/2" 257964 3/8" x 10" Screen Tube † 1/2" 257959 3/8" x 12" Screen Tube † 1/2" 257965 1/2" x 3-1/2" Screen Tube 5/8" 257966 1/2" x 6" Screen Tube 5/8" 257967 1/2" x 8" Screen Tube † 5/8" 257968 1/2" x 10" Screen Tube † 5/8" 257969 5/8" x 4-1/2" Screen Tube 3/4" 207970 5/8" x 6" Screen Tube 3/4" 207971 5/8" x 8" Screen Tube † 3/4" 207972 5/8" x 10" Screen Tube † 3/4" 207973 3/4" x 6" Screen Tube 7/8" 107977 3/4" x 8" Screen Tube 7/8" 107974 3/4" x 10" Screen Tube 7/8" 107975 3/4" x 13" Screen Tube 7/8" 107865 15/16" x 8" Screen Tube 1" 107867 15/16" x 13" Screen Tube 1" 107869 15/16" x 17" Screen Tube † 1" 107955 Adhesive Shear Tube (steel sleeve) — 10

PART STD. STD.NO. DESCRIPTION BOX CTN.6046* 7/8" x 10-1/4" Anchor Rod 10 40


304 Stainless Steel Anchor Rod

282SS 5/19/10 5:03 PM Page 282

283

Fasteners

Powerfoam™ / TriggerFoam™

Expanding Polyurethane FoamBase MaterialConcrete, Masonry, Wood, MetalSize Range12 oz. and 29 oz.MaterialPolyurethane

Powerfoam and TriggerFoam are one-part polyurethane expandingfoams that set and cure into their final form by reacting to moistureand humidity present in the air. Their exceptional ability to bondallows Powerfoam and TriggerFoam to be applied to various buildingelements including the surfaces of concrete, brick, block, wood,steel, aluminum and other miscellaneous metals. Powerfoam andTriggerFoam are safe to use, containing no CFC’s, no PCB’s and noUrea Formaldehyde. As they are being dispensed, Powerfoam andTriggerFoam have a neutral odor. Cured foam is physiologicallyharmless. Foam products are offered in standard yellow.

PowerStick™Adhesive SealantBase MaterialConcrete, Masonry, Metals, Wood, PlasticsSize Range7 oz. and 10 oz. tubesAnchor MaterialMS Polymer Chemistry

PowerStick is a one-component universal adhesive/sealant based onproprietary MS Polymer chemistry. PowerStick is the firstprofessional grade product on the market that delivers high bondstrength and superior flexibility.

PowerFoam™PART STD. STD. STD.NO. SIZE BOX CTN. PALLET8130 PowerFoam™ 12 oz. 12 12 11528132 PowerFoam™ 29 oz. 12 12 6128136 TriggerFoam™ 29 oz. 12 12 612

Caulking Guns for PowerstickPART STD. STD.NO. DESCRIPTION BOX CTN.8437 Manual Caulking Gun 1 128463 High Performance Manual Tool 1 1

PART STD. STD.NO. SIZE COLOR DISPENSER BOX CTN.8166 10 oz. White Caulk Gun 12 128168 10 oz. Gray Caulk Gun 12 128170 7 oz. White Press Pack 12 128172 7 oz. Gray Press Pack 12 12

TriggerFoam™ Tools & AccessoriesPART STD. STD.NO. SIZE BOX CTN.8139 TriggerFoam™ Plastic Gun 1 108138 TriggerFoam™ Heavy Duty Gun 1 18140 TriggerFoam™ Metal Gun 1 108141 TriggerFoam™ Gun replacement brass tip 1 18142 TriggerFoam™ Cleaner 20 oz. 12 128137 TriggerFoam™ Subfloor Gun 22" 1 1

8138 8139

8140 8142

283SS 5/19/10 5:04 PM Page 283

284

Fasteners

ANCHOR CATEGORY METAL PLASTICS

PRODUCT

Wall Anchor Selection Guides

■ Suitable ■■ May Be Suitable

Wal

l-Dog

Scru

-Lea

d

Togg

le-B

olt

Polly

Legs

Shar

kie

Stra

p-To

ggle

Zip-

It(A

lso

Avai

labl

e in

Zin

c)

Zip-

Togg

le

Poly

-Tog

gle

Pop

Togg

le

Bant

am P

lug

Flut

ed P

last

ic

Concrete ■ ■ ■ ■ ■■ ■ ■Lightweight Concrete ■■ ■■ ■ ■■ ■■ ■■ ■■

Hollow Core Plank ■ ■■ ■ ■■ ■ ■ ■■ ■■ ■■ ■■Grout-filled Concrete Masonry ■ ■■ ■ ■■ ■■ ■■ ■■

Hollow Concrete Masonry ■ ■■ ■ ■ ■■ ■ ■ ■■ ■■ ■■Solid Brick ■ ■ ■ ■■ ■■ ■ ■■

Hollow Brick ■■ ■■ ■■ ■■ ■■ ■■ ■■ ■■ ■■Stone ■■ ■ ■■ ■■

Structural Clay Tile ■■ ■■ ■■ ■■ ■■ ■■Plywood ■ ■ ■ ■■ ■■ ■■ ■

Wallboard /Plaster ■ ■ ■ ■ ■■ ■ ■ ■ ■ ■ ■ ■■No. 4 Screw ■ ■No. 5 Screw ■ ■No. 6 Screw ■ ■ ■ ■ ■ ■ ■ ■ ■No. 7 Screw ■ ■ ■ ■ ■ ■ ■ ■No. 8 Screw ■ ■ ■ ■ ■ ■ ■ ■No. 9 Screw ■ ■ ■ ■ ■

No. 10 Screw ■ ■ ■ ■ ■ ■No. 12 Screw ■ ■ ■ ■ ■ ■No. 14 Screw ■ ■ ■ ■ ■No. 16 Screw ■ ■No. 18 Screw ■

1/8" ■ ■3/16" ■ ■ ■1/4" ■ ■ ■ ■

5/16" ■3/8" ■ ■1/2" ■ ■

Finished (Hex) Head ■ ■Round Head ■

Flat Head (Countersunk) ■ ■Mushroom Head ■ ■ ■

Removable ■ ■Under 400 lbs. ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

400 lbs. to 4,000 lbs. ■ ■Over 4,000 lbs.

Coated / Plated Carbon Steel ■ ■ ■ ■ ■Zamac Alloy ■

Nylon / Plastic ■ ■ ■ ■ ■ ■ ■ ■Lead ■Co

atin

g/M

ater

ial

Wor

king

Load

Head

Styl

eAn

chor

Dia

met

erBa

se M

ater

ial

284SS 5/19/10 5:04 PM Page 284

285

Fasteners

PART DRILL STD. STD.NO. SIZE DIA. BOX CTN.4023 1/8" x 2" 3/8" 50 5004033 1/8" x 3" 3/8" 50 5004043 1/8" x 4" 3/8" 50 5004133 3/16" x 3" 1/2" 50 5004143 3/16" x 4" 1/2" 50 5004233 1/4" x 3" 5/8" 50 5004243 1/4" x 4" 5/8" 50 500

Combo Mushroom Head

PART DRILL STD. STD.NO. SIZE DIA. BOX CTN.4038 1/8" x 3" 3/8" 50 500

Slotted Hex Head

Scru-Lead™

Wall AnchorBase MaterialConcrete, Block, Brick

Size RangeNo.6-8 x 3/4” to No.16-18 x 1-1/2"

Anchor MaterialLead alloy

The Scru-Lead™ anchor is designed for use with sheet metal or woodscrews in concrete, block or brick. The anchor is made entirely of leadalloy which is soft enough for easy installation, yet hard enough to givesure, secure holding power. The performance of this product dependson the integrity of the base material. The anchor is recommended forlight duty applications where holding power is not a critical factor. Itshould not be used overhead.

PART DRILL STD. STD.NO. SIZE DIA. BOX CTN.4021 1/8" x 2" 3/8" 50 5004031 1/8" x 3" 3/8" 50 5004041 1/8" x 4" 3/8" 50 5004121 3/16" x 2" 1/2" 50 5004131 3/16" x 3" 1/2" 50 5004141 3/16" x 4" 1/2" 50 5004151 3/16" x 5" 1/2" 50 5004161 3/16" x 6" 1/2" 50 5004231 1/4" x 3" 5/8" 50 5004241 1/4" x 4" 5/8" 50 5004251 1/4" x 5" 5/8" 50 5004261 1/4" x 6" 5/8" 50 5004341 5/16" x 4" 7/8" 25 2504431 3/8" x 3" 7/8" 25 2504441 3/8" x 4" 7/8" 25 2504451 3/8" x 5" 7/8" 25 1254461 3/8" x 6" 7/8" 25 1254541 1/2" x 4" 1-1/4" 25 25

Combo Round Head

Toggle BoltHollow Wall Anchor

Base MaterialHollow block, wallboard, plaster

Size Range1/8"x 2" to 1/2" x 6"


The Toggle Bolt is a spring wing type hollow wall anchor designed foruse in block, wallboard and other hollow base materials. The ToggleBolt is a two-part assembly consisting of a machine screw and aspring wing toggle. Sizes range from 1/8" x 2" to 1/2" x 6" with comboround, flat, mushroom, tie-wire or slotted hex head styles.

PART DRILL MIN. STD. STD.NO. SIZE DIA. DEPTH BOX CTN.9409 6-8 x 3/4" 1/4" 3/4" 100 10009414 6-8 x 1" 1/4" 1" 100 5009419 6-8 x 1-1/2" 1/4" 1-1/2" 100 5009429 10-14 x 1" 5/16" 1" 100 5009439 10-14 x 1-1/2" 5/16" 1-1/2" 100 5009460 16-18 x 1-1/2" 3/8" 1-1/2" 25 250

PART DRILL STD. STD.NO. ANCHOR SIZE DIA. BOX CTN.9430 #10 – #14 x 1" 5/16" 1000 10000

MASTER CARTON

285SS 5/19/10 5:04 PM Page 285

286

Fasteners

PART SCREW DRILL WALL STD. STD.NO. SIZE LENGTH DIA. THICKNESS BOX CTN.2100 1/8"XS 1-1/16" 5/16" 1/8"–1/4" 100 5002101 1/8"S 1-3/4" 5/16" 3/8"–1/2" 100 5002102 1/8"L 2-1/4" 5/16" 5/8"–1" 100 5002111 3/16"S 2" 3/8" 3/8"–5/8" 50 2502112 3/16"L 2-1/2" 3/8" 3/4"–1-1/8" 50 2502113 3/16"XL 3" 3/8" 1-1/4"–1-3/4" 25 1252121 1/4"S 2-1/4" 7/16" 3/8"–1/2" 50 2502122 1/4"L 2-3/4" 7/16" 5/8"–1-1/8" 50 2502123* 1/4"XL 3-3/8" 7/16" 1-1/4"–1-3/4" 25 125

Combination Slotted Phillips Head Polly™

Polly™

Hollow Wall AnchorBase MaterialPlaster, wallboard, block, hollow tile, plywood

Size Range1/8” extra short to 1/4” extra long


The Polly™ is a sleeve type hollow wall anchor designed for use inbase materials such as plaster, wallboard, concrete block, hollow tile or plywood.

PART SCREW DRILL WALL STD. STD.NO. SIZE LENGTH DIA. THICKNESS BOX CTN.2105 1/8"S 1-3/4" 5/16" 3/8"–1/2" 100 500

Slotted Hex Head Polly™

PART SCREW DRILL WALL STD. STD.NO. SIZE LENGTH DIA. THICKNESS BOX CTN.2180* 1/8"XS 1-3/8" 1/8"–1/4" 100 5002182 1/8"S 2" 3/8"–1/2' 100 5002184 1/8" L 2-3/8" 1/2"–3/4" 100 500

Drive Polly™

PART STD. STD.NO. DESCRIPTION BOX CTN.2150 POLLY™ Setting Tool 1 1

Polly™ Setting Tool (Fits all sizes)

PART DRILL STD. STD.NO. SIZE DIA. BOX CTN.4032* 1/8" x 3" 3/8" 50 5004132 3/16" x 3" 1/2" 50 5004142 3/16" x 4" 1/2" 50 5004232 1/4" x 3" 5/8" 50 500

Flat Head

PART DRILL STD. STD.NO. SIZE DIA. BOX CTN.4000 1/8" 3/8" 100 5004020 3/16" 1/2" 100 10004220 1/4" 5/8" 100 10004330 5/16" 7/8" 50 5004430 3/8" 7/8" 50 5004540 1/2" 1-1/4" 25 25

Toggle Wings Only

PART TIE WIRE DRILL STD. STD. NO. SIZE HOLE SIZE DIA. BOX CTN.4247 1/4" x 4" 7/32" 5/8" 100 1004257 1/4" x 5" 7/32" 5/8" 100 100

Tie-Wire Acoustical Toggle


*Discontinued item once current stock exhausted.XS - Extra Short S - Short L - Long XL - Extra Long

*Discontinued item once current stock exhausted.XS - Extra Short S - Short L - Long

286SS 5/19/10 5:04 PM Page 286

287

Fasteners

Legs®

Wallboard AnchorBase MaterialWallboardSize RangeUse with No.6 or No.8 screwAnchor MaterialCarbon Steel

The LEGS® anchor is a fast, easy to use expansion anchor designedfor use in wallboard. The anchor has a pierce point, requiring no pre-drilling. Removal of the anchor, if required, is easy. Once removed,the anchor leaves a small slit in the wallboard.

Strap-Toggle™

Hollow Wall AnchorBase MaterialHollow Wallboard or Hollow BlockSize Range3/16" x 4" to 1/2" x 4"Anchor MaterialPlastic

The Strap-Toggle™ is a pre-assembled anchor consisting of a carbonsteel wing and a locking cap / ratchet leg assembly molded fromengineered plastic. When compared to traditional toggles, thisunique anchor can be installed through a smaller hole and does notrequire a fixture or screw to set it.

Zip-It®

Wallboard AnchorBase MaterialWallboardSize RangeUse with No. 6 or No. 8 screwAnchor MaterialEngineered Nylon or Zamac Alloy

The Zip-It® anchor is a one piece self drilling anchor designed for usein hollow gypsum wallboard for light duty loads. It is available inboth engineered nylon and Zamac alloy for use with either a No. 6 orNo. 8 screws in 3/8" to 1" wallboard. The Zip-It® Jr. is formed fromengineered nylon for use with No. 6 screws in 3/8" to 5/8" wallboard.

Legs® Drywall Anchor PART STD. STD.NO. SIZE BOX CTN.2336 LEGS® Wallboard Anchor 100 10002335 LEGS® Anchor w/ No.8 x 1" Screw 100 1000 PART DRILL WALL STD. STD.

NO. SIZE DIA. THICKNESS BOX CTN.4052 3/16” x 4” 1/2" 2-1/2" 50 3004054 1/4” x 4” 1/2" 2-1/2" 50 3004056 3/8” x 4” 3/4" 2-1/2" 25 1504058 1/2” x 4” 3/4" 2-1/2" 25 150

Sharkie™Plastic Wall AnchorBase MaterialConcrete, Block, Brick & WallboardSize RangeUse with No.6 x 1” to No.14 x 1-9/16” screwAnchor MaterialPlastic

The Sharkie™ is a one-piece plastic anchor designed forlight duty applications in wallboard, concrete andmasonry.The Sharkie works in hollow or solid base materials and issuitable for screws with various thread sizes and styles. Screws forthe anchor may be installed with a screw gun.The top of the Sharkieis available with and without a flange at the top of the anchor tomatch the application.

Sharkie™ Drywall AnchorPART STD. STD.NO. SIZE BOX CTN.7580 Sharkie Anchor Flange #4-#10 100 10007581 Sharkie Anchor No-Flange #4-#10 100 10007582 Sharkie Anchor Flange #6-#12 100 10007583 Sharkie Anchor No-Flange #6-#12 100 10007584 Sharkie Anchor Flange #8-#14 100 5007585 Sharkie Anchor No-Flange #8-#14 100 500

Master PackLegs® Drywall Anchor PART MASTERNO. SIZE CTN.2338 LEGS® Wallboard Anchor 5000

287SS 5/19/10 5:05 PM Page 287

288

Fasteners

PART STD. STD.NO. SIZE SCREWS BOX CTN.2290 Zip-Toggle™ with screws No.6 x 2" 50 2502295 Metal Zip-Toggle™ with screws No.6 x 2" 50 250

Zip-Toggle™Plastic Hollow Wall AnchorBase MaterialWallboard

Size Range3/8"

Anchor MaterialEngineered Nylon or Zamac AlloyThe Zip-Toggle™ is a hollow gypsum wallboard anchor designed toprovide superior performance without the need to pre-drill largerdiameter holes. The Zip-Toggle™ is packaged with its own No. 6 x 2"lubricated screw.

PART WALL DRILL STD. STD.NO. SIZE THICKNESS DIA. BOX CTN.2302 Mini 1/8" 5/16" 100 10002303 Short 3/8" 5/16" 100 10002304 Medium 1/2" 5/16" 100 10002305 Long 5/8" 5/16" 100 1000

Poly-Toggle™Plastic Hollow Wall AnchorBase MaterialWallboard or solid masonry

Size Range1/8” to 1” wall thickness

Anchor MaterialPlastic

The Poly-Toggle™ is a screw actuated hollow wall anchor for use inpaneling, wallboard and solid masonry available in 6 sizes to match themost common wall thicknesses. In solid base materials, the anchorcan be used by removing the outer wings. The performance of thisproduct depends on the integrity of the base material in which it isinstalled. The anchor is recommended for light duty static applicationwhere holding power is not a critical factor.

PART WALL STD. STD.NO. THICKNESS DESCRIPTION BOX CTN.2345 3/8" to 1" Std. box, no screws 100 10002348 3/8" to 1" Std. box, No.8 x 1"screws 100 10002355 3/8" to 1" Master ctn., no screws — 5000

Nylon Zip-It®

PART WALL STD. STD.NO. THICKNESS DESCRIPTION BOX CTN.2346 3/8" to 1" Std. box, no screws 100 10002349 3/8" to 1" Std. box, No.8 x 1"screws 100 10002356 3/8" to 1" Master ctn., no screws — 1000

Zinc Zip-It®

PART WALL STD. STD.NO. THICKNESS DESCRIPTION BOX CTN.2350 3/8"-5/8" Std. Box (No screws) 100 10002351 3/8"-5/8" Std. Box, No. 6 x 1" screws 100 1000

Nylon Zip-It Jr.

PART WALL STD. STD.NO. THICKNESS DESCRIPTION BOX CTN.2362 3/8"-5/8" Std. Box (No screws) 100 10002364 3/8"-5/8" Std. Box, No. 6 x 1" screws 100 10002363 3/8"-5/8" Master Ctn. (No screws) - 5000

Zinc Zip-It Jr.

PART STD. STD.NO. MATERIAL DESCRIPTION BOX CTN.2368 Nylon 50 Anchors , No. 8 x 1" screws, 1 10

& No. 2 Phillips Driver Bit2369 Zinc 50 Anchors & No. 8 x 1" screws 1 10

& No. 2 Phillips Driver Bit

Zip-It® Kits

PART STD. STD.NO. MATERIAL DESCRIPTION BOX CTN.2367 Nylon 50 Anchors, No. 6 x 1" screws, 1 10

and No. 2 Phillips Driver Bit

Zip-It Jr. Kits

288SS 5/19/10 5:05 PM Page 288

289

Fasteners

Pop-Toggle™

Hollow Wall AnchorBase MaterialGypsum Wallboard, Plaster, Plywood & some Hollow Masonry

Size RangeWall thickness from 1/8" to 3/4", No. 6 to No. 14 wood or sheet metal screws


Pop-Toggle™ fasteners are hollow wall anchors ideal for staticapplications requiring light to medium load performance. Installationis very fast, needing a pre-drilled 5/16" diameter hole. The fastenerpre-installs without a screw, allowing for easy placement andremoval of the fixture. Pop-Toggle™ fasteners are not recommendedfor use overhead or applications where holding values are critical.

Kits — Slotted/Phillips Pan Head Sheet Metal Screws

100 Anchors and screws plus one drill bit per kit

* Discontinued item once current stock exhausted.

PART STD. STD.NO. DESCRIPTION BOX CTN.4060 Pop-Toggle™ Small 100 10004062 Pop-Toggle™ Medium 100 10004064 Pop-Toggle™ Large 100 1000

Bantam Plug™

Plastic Wall AnchorBase MaterialConcrete, Block, Brick, Wallboard

Size RangeNo. 6-8 x 3/4" to No. 14-16 x 1-1/2"


The Bantam Plug™ anchor is a plastic anchor designed for use withlightweight fixtures with a sheet metal or wood screw. The anchor isrecommended for light duty static applications where holding poweris not a critical factor. It should not be used overhead.

Fluted Plastic AnchorPlastic Wall AnchorBase MaterialConcrete, Block, Brick, Stone

Size RangeNo. 4-6 x 1" to No.14 x 1-1/2"


The Fluted Plastic Anchor is designed for light duty fasteningapplications with sheet metal or wood screws. Longitudinal ribs onthe anchor body prevent it from turning during tightening of thescrew. This inexpensive plastic screw anchor comes color-coded bydiameter for easy application. The anchor is recommended for lightduty static applications where holding power is not a critical factor. It should not be used overhead.

PART DRILL MIN. STD. STD. MASTERNO. SIZE DIA. DEPTH BOX CTN. CTN.7559 6-8 x 3/4" 3/16" 3/4" 100 1000 150,0007569 8-10 x 7/8" 3/16" 7/8" 100 1000 150,0007579 10-12 x 1" 1/4" 1" 100 1000 80,0007589 14-16 x 1-1/2" 5/16" 1-1/2" 50 500 40,000

PART ANCHOR SCREW MIN. ANCHORS STD.NO. KIT NO. SIZE SIZE DEPTH & SCREWS CTN.8934 B-8 8-10 No. 8 x 1" 7/8" 100 108936 B-10 10-12 No. 10 x 1" 1" 100 108938 B-12 10-12 No. 12 x 1" 1" 100 10

PART DRILL MIN. STD. STD.NO. SIZE COLOR DIA. DEPTH BOX CTN.7500 4-6 x 1" White 3/16" 1" 100 10007505* 7-9 x 1" Red 7/32" 1" 100 10007510 10-12 x 1" Green 1/4" 1" 100 10007515 10-12 x 1-1/4" Green 1/4" 1-1/4" 100 10007520 10-12 x 1-1/2" Green 1/4" 1-1/2" 100 10007525* 14 x 1" Blue 5/16" 1" 100 10007530 14 x 1-1/2" Blue 5/16" 1-1/2" 100 1000

New products

are constantly added

to our inventory

289SS 5/19/10 5:05 PM Page 289

290

Fasteners

THREADED HEAVYPIN CATEGORY 0.300" HEAD DRIVE PIN 8MM HEAD DRIVE PIN STUDS DUTY PINS

PRODUCT

Powder Actuated Selection Guides

■ Suitable ■■May Be Suitable

.300

" Hea

d Dr

ive

Pin

with

Top

Hat

.300

" Hea

d St

epSh

ank

Driv

e Pi

ns

8mm

Hea

dDr

ive

Pin

8mm

Hea

d Dr

ive

Pin

with

Top

Hat

8mm

Hea

d Dr

ive

Pin

with

1" W

ashe

rs

1/4"

– 2

0Th

read

ed S

tud

3/8"

– 1

6Th

read

ed S

tud

3/8"

Hea

d Dr

ive

Pin

10m

m H

ead

Driv

e Pi

n

.300

" Hea

d Dr

ive

Pin

with

Was

hers

.300

" Hea

dDr

ive

Pin

1/2" 1-3/4" 1/2" 3/4" 2" 3/4" 5/8" 1-5/8" 5/8" 1" 2" 1/2" 3/4" 1" 3/4"to to to to to to to to to to to to to to to

Shank Length 1-1/2" 3" 1" 1-1/2" 3" 1" 1-1/2" 2-7/8" 1" 1-1/2" 2-7/8" 1-1/4" 1-1/4" 3-1/8" 3-1/4"Shank Diameter 0.145" .145/.130" 0.145" 0.145" 0.205" 0.177"

Concrete ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■Lightweight Concrete ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

Grout-filled Concrete Masonry ■ ■■ ■■ ■ ■■ ■ ■■ ■■ ■■ ■■ ■■ ■■ ■■ ■■Steel ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

Gray – Power Level 1Brown – Power Level 2Green – Power Level 3Yellow – Power Level 4

Red – Power Level 5Purple/Black – Power Level 6

P3600 ■ ■PA351 ■■ ■■ ■■ ■■ ■ ■■ ■■P3801 ■■ ■ ■ ■

P3500 / PA3500 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■P35s ■ ■ ■ ■ ■ ■ ■

P7201 ■ ■ ■ ■ ■ ■ ■ ■P2201 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■P1000 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

Hammer Drive Tool721 ■ ■ ■ ■ ■ ■ ■ ■M70 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

LADD (L1600)D45 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

D60 / D60L ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■MD380 ■ ■SA270 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■Cobra ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■Viper ■ ■ ■ ■ ■ ■ ■

DX E37 ■ ■ ■ ■ ■ ■ ■ ■DX E72 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■DX400 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

DX600N ■ ■ ■■DX35 ■ ■ ■ ■ ■ ■ ■ ■

DX350 / DX351 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■DX36M ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■DX 450DX451 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■DXA40 ■ ■ ■ ■ ■ ■ ■ ■ ■DXA41 ■■ ■■ ■■ ■■ ■■ ■■ ■■ ■■ ■■ ■■ ■■ ■■ ■ ■ ■DX100 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■DX200 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■DX460 ■■ ■■ ■■ ■■ ■ ■■ ■■

.172".216/.188"

Othe

r Too

lsPo

wer

s To

ols

Load

Pow

erLe

vel

Base

Mat

eria

lPi

nDi

men

sion

s

290SS 5/19/10 5:05 PM Page 290

291

Fasteners

BALLISTIC SPECIALTY CLIPS ANDPIN CATEGORY POINT PIN FASTENERS ACCESSORIES POWDER ACTUATED LOADS

PRODUCT

Powder Actuated Selection Guides (cont.)

■ Suitable ■■May Be Suitable

Balli

stic

Poi

nt P

in

Form

ing

Pin

Ham

mer

Driv

e Pi

n

Ceili

ng C

lip A

ssem

blie

s(.

300"

, 8m

m &

Bal

listic

Poi

ntCe

iling

Clip

Ass

embl

ies

Ladd

Too

l (L1

600)

BX –

EM

T Co

ndui

t Clip

Asse

mbl

ies

(.30

0"&

8m

m)

Reba

r Bas

ket C

lipAs

sem

blie

s (8

mm

).2

2 Ca

liber

“A”

Sing

le L

oad

.22

Calib

er S

ingl

e Lo

ads

Ladd

Too

l (L1

600)

.25

Calib

er D

isk

Load

.25

Calib

er D

isk

Load

s(R

ed)

.25

Calib

er S

ingl

e Lo

ad

.27

Calib

er S

ingl

e Lo

ad

.27

Calib

er S

ingl

eLo

ng L

oads

.25

Calib

er 1

0Lo

ad S

trip

.27

Calib

er 1

0Lo

ad S

trip

(Pur

ple/

Blac

k)

.27

Calib

er S

afet

y St

rip

Balli

stic

Poi

ntSt

ep S

hank

Pin

1/2" 1-3/4" 3/4" 1" 1" 1-1/4"

to 1-1/4" 1-7/8" to to to 1-1/2" to to

Shank Length 7/8" 2-1/2" 3" 1-1/4" 1-1/4" 2-7/8"

Shank Diameter 0.150" 0.181"/0.150" 0.145" 0.140" 0.145" 0.155" 0.145" 0.145"

Concrete ■ ■ ■ ■ ■ ■ ■ ■ ■Lightweight Concrete ■ ■ ■ ■ ■ ■ ■ ■

Grout-filled Concrete Masonry ■■ ■■ ■■ ■■ ■■ ■■ ■■Steel ■ ■ ■■ ■ ■ ■ ■■

Gray – Power Level 1 ■ ■Brown – Power Level 2 ■ ■ ■ ■Green – Power Level 3 ■ ■ ■ ■ ■ ■ ■ ■Yellow – Power Level 4 ■ ■ ■ ■ ■ ■ ■ ■

Red – Power Level 5 ■ ■ ■ ■ ■ ■ ■Purple/Black – Power Level 6 ■ ■ ■ ■ ■

P3600 ■ ■PA351 ■P3801 ■ ■

P3500 / PA3500 ■ ■ ■ ■ ■ ■ ■ ■P35s ■ ■ ■ ■ ■

P7201 ■ ■ ■ ■ ■P2201 ■ ■ ■ ■ ■ ■ ■ ■P1000 ■ ■ ■ ■ ■ ■ ■ ■

Hammer Drive Tool ■721 ■ ■ ■ ■ ■M70 ■ ■ ■ ■ ■ ■ ■ ■

LADD (L1600) ■ ■D45 ■ ■ ■ ■ ■ ■ ■ ■ ■

D60 / D60L ■ ■ ■ ■ ■ ■ ■ ■MD380 ■SA270 ■ ■ ■ ■ ■ ■ ■ ■Cobra ■ ■ ■ ■ ■ ■ ■ ■Viper ■ ■ ■ ■

DX E37 ■ ■ ■ ■ ■DX E72 ■ ■ ■ ■ ■ ■ ■ ■DX400 ■ ■ ■ ■ ■ ■ ■

DX600N ■ ■DX35 ■ ■ ■ ■ ■

DX350 / DX351 ■ ■ ■ ■ ■ ■ ■ ■DX36M ■ ■ ■ ■ ■ ■ ■ ■DX 450 ■ ■DX451 ■ ■ ■ ■ ■DXA40 ■ ■ ■ ■ ■ ■DXA41 ■ ■ ■ ■ ■ ■ ■ ■DX100 ■ ■ ■ ■ ■ ■ ■ ■DX200 ■ ■ ■ ■ ■ ■ ■ ■DX460 ■

Othe

r Too

lsPo

wer

s To

ols

Load

Pow

erLe

vel

Base

Mat

eria

lPi

nDi

men

sion

s

291SS 5/19/10 5:06 PM Page 291

292

Fasteners

PART HEAD SHANK STD. STD.NO. SHANK LENGTH DIA. DIA. BOX CTN.50012 1/2" (knurled) .300 .145 100 500050016 5/8" (knurled) .300 .145 100 500050022 3/4" .300 .145 100 500050023 3/4” Black .300 .145 100 500050026 1" .300 .145 100 500050030* 1-1/8" .300 .145 100 100050032 1-1/4" .300 .145 100 100050034 1-1/2" .300 .145 100 100050038 2" .300 .145 100 100050040 2-1/4" .300 .145 100 100050042* 2-3/8" .300 .145 100 100050044 2-1/2" .300 .145 100 100050046 2-3/4" .300 .145 100 100050048 3" .300 .145 100 1000

PART HEAD SHANK STD. STD.NO. SHANK LENGTH DIA. DIA. BOX CTN.50980 1/2" knurled .300 .145 1000 500051041 3/4" Black Pins .300 .145 1000 500053300 5/8" knurled .300 .145 1000 500053400* 5/8" knr.Top Hat .300 .145 1000 500051040 3/4" .300 .145 1000 500051100 1" .300 .145 1000 500051160 1-1/4" .300 .145 1000 500051340 1/2" knr.Top Hat .300 .145 1000 500051400 3/4" Top Hat .300 .145 1000 500051520 1" Top Hat .300 .145 1000 5000

PART HEAD SHANK STD. STD.NO. SHANK LENGTH DIA. DIA. BOX CTN.50136 1/2" knurled .300 .145 100 500050138 5/8" knurled .300 .145 100 500050140 3/4" .300 .145 100 500050144 1" .300 .145 100 5000

PART HEAD SHANK STD. STD.NO. SHANK LENGTH DIA. DIA. BOX CTN.50158* 3/4" Step Shank .300 .145/.130 100 500050159* 1" Step Shank .300 .145/.130 100 5000

Master Pack

.300 Head Drive PinsStandard PinsDrive pins with a .300 diameter head are designed for permanentlyfastening a fixture to concrete, some types of masonry and A36structural steel. Drive pins are manufactured with a 0.143" diameter shank in variouslengths. Knurled shank designs are available to increase performancein steel base materials. A plastic flute is mounted over the point toretain the drive pin in the fastener guide of the tool providing guidanceduring the driving operation.

.300 Head Drive Pins




.300 Head Step Shank Pins

PART WT./ SHANK STD. STD.NO. SHANK LENGTH 100 DIA. BOX CTN.56000 1/2" .900 .145 100 500056004 3/4" .900 .145 100 500056006 1" .900 .145 100 500056012 1-1/2" .900 .145 100 5000

.300 Blue Magic™ Drive PinsBlue Magic™ pins offer a hard plastic flute for improved centering inthe tool and tip protection.

.300 Head Drive Pins with Top HatThe pins listed below are used primarily for applications fasteningdrywall track to concrete or steel. They are assembled with a metal tophat to provide extra bearing surface against the drywall track.

PART HEAD SHANK STD. STD.NO. SHANK LENGTH DIA. DIA. BOX CTN.50070 3/4" .300 .145 100 100050080 2-1/2" .300 .145 100 1000

Washered PinsTo provide resistance to pullover, these pins are available withpreassembled 14 gauge (0.075") metal washers in various diameters.The insulation washer has a thickness of 0.035".

.300 Head Drive Pins with 3/4" Washer

PART HEAD SHANK STD. STD.NO. SHANK LENGTH DIA. DIA. BOX CTN.50090 1" .300 .145 100 100050092 1-1/4" .300 .145 100 100050094 1-1/2" .300 .145 100 100050096 2" .300 .145 100 100050098 2-1/2" .300 .145 100 100050100 3" .300 .145 100 1000

.300 Head Drive Pins with 7/8" Washer

PART HEAD SHANK STD. STD.NO. SHANK LENGTH DIA. DIA. BOX CTN.50108 1-1/4" .300 .145 100 100050110 1-1/2" .300 .145 100 100050112 2" .300 .145 100 100050114 2-1/2" .300 .145 100 100050116 3" .300 .145 100 1000

.300 Head Drive Pins with 1" Washer

292SS 5/19/10 5:06 PM Page 292

293

Fasteners

PART HEAD SHANK STD. STD.NO. SHANK LENGTH DIA. DIA. BOX CTN.50122 1-1/2" .300 .145 100 100050126 2-1/2" .300 .145 50 500

.300 Head Drive Pins with 1-7/16" Insulation Washer

PTZ PowderActuated Fasteners

The Powers PTZ Powder Actuated Fasteners are designed for fasteningthrough pressure treated lumber into concrete and grout filled masonry. Thefasteners are manufactured to provide a minimum level of corrosion resistanceequivalent to triple zinc coatings found on connector hardware available forpressure treated lumber applications. The fasteners are available with either around or square washer for increased pullover resistance.

ACQ

PART NO. SHANK LENGTH STD. BOX STD. CTN.50097 2-1/2" 100 100050101 3" 100 1000

PART NO. SHANK LENGTH STD. BOX STD. CTN.50113 2-1/2" 100 100050115 3" 100 1000

PTZ .300 Head Pin with 7/8" Washer

PTZ .300 Head Pin with 1" Washer

PART NO. SHANK LENGTH STD. BOX STD. CTN.50229 72mm 100 1000

PTZ 8mm Head Pin with 1" Washer

PART NO. SHANK LENGTH STD. BOX STD. CTN.50231 72mm 100 1000

PTZ 8mm Head Pin with 1" Square Washer

PART NO. SHANK LENGTH STD. BOX STD. CTN.50119 3" 100 1000

PTZ .300 Head Pin with 1" Square Washer

8mm Head Drive PinsX-DN Type Pins 8mm Head Drive Pins

PART HEAD SHANK STD. STD.NO. SHANK LENGTH DIA. DIA. BOX CTN.50180 16mm knrld – 5/8" 8mm .145 100 500050182 19mm knrld – 3/4" 8mm .145 100 500050184 22mm – 7/8" 8mm .145 100 500050186 27mm – 1" 8mm .145 100 500050188 32mm – 1-1/4" 8mm .145 100 100050190 37mm – 1-1/2" 8mm .145 100 100050192 42mm – 1-5/8" 8mm .145 100 100050194 47mm – 1-7/8" 8mm .145 100 100050196 52mm – 2" 8mm .145 100 100050198 57mm – 2-1/4" 8mm .145 100 100050200 62mm – 2-1/2" 8mm .145 100 100050202 72mm – 2-7/8" 8mm .145 100 1000

PART HEAD SHANK STD. STD.NO. SHANK LENGTH DIA. DIA. BOX CTN.50210 16mm knrld – 5/8" 8mm .145 100 500050214 22mm – 7/8" 8mm .145 100 500050216 27mm – 1" 8mm .145 100 5000

8mm Diameter Head Drive Pins with Top HatThe pins listed below are used primarily for applications fasteningdrywall track to concrete or steel. They are assembled with a metaltop hat to provide extra bearing surface against the drywall track.

PART HEAD SHANK STD. STD.NO. SHANK LENGTH DIA. DIA. BOX CTN.51700 16mm knr. T Hat 8mm .145 1000 500051750 22mm Top Hat 8mm .145 1000 5000

Master Pack

Washered PinsTo provide resistance to pullover, these pins are available withpreassembled 14 gauge (0.075") metal washers in various diameters.

293SS 5/19/10 5:06 PM Page 293

294

Fasteners

Ballistic Point™ Drive PinsPower Point-type FastenersPremium drive pins with a .300 diameter head have a speciallydesigned point to allow more consistent penetration into harder basematerials. Will reduce failures in dense concrete and steel. Drive Pinsare manufactured with a 0.150" diameter straight and step shank invarious lengths. A plastic flute is mounted over the point to retain thedrive pin in the fastener guide of the tool providing guidance duringthe driving operation.

Ballistic Point Drive Pins (Black)PART HEAD SHANK STD. STD.NO. SHANK LENGTH DIA. DIA. BOX CTN.50052 1/2" .300 .150 100 100050054 3/4" .300 .150 100 1000

PART HEAD SHANK STD. STD.NO. SHANK LENGTH DIA. DIA. BOX CTN.50220 27mm – 1" 8mm .145 100 100050222 32mm – 1-1/4" 8mm .145 100 100050224 37mm – 1-1/2" 8mm .145 100 100050226 52mm – 2" 8mm .145 100 100050228 62mm – 2-1/2" 8mm .145 100 100050230 72mm – 2-7/8" 8mm .145 100 1000

8mm Head Diameter Drive Pins with 1" Washer

8mm Head Collated Drive Pins10 Fastener Magazine for PA351 and DX460

PART SHANK SHANK HEAD SHANK STD. STD.NO. LENGTH (in.) LENGTH (mm) DIA. DIA. BOX CTN.50244 3/4" 19 8mm .145 500 250050246 7/8" 22 8mm .145 500 250050248 1" 27 8mm .145 500 250050250 1-1/4" 32 8mm .145 500 250050252 1-1/2" 37 8mm .145 500 250050254 1-5/8" 42 8mm .145 500 250050256 1-7/8" 47 8mm .145 500 250050258 2" 52 8mm .145 500 250050260 2-1/4" 57 8mm .145 500 250050262 2-1/2" 62 8mm .145 500 250050264 2-7/8" 67 8mm .145 500 250050240 5/8" K 16 8mm .145 500 250050242 3/4" K 19 8mm .145 500 2500

K = Knurled

PART HEAD SHANK STD. STD.NO. SHANK LENGTH DIA. DIA. BOX CTN.50850 27mm – 1" 10mm .177 100 100050852 32mm – 1-1/4" 10mm .177 100 100050854 42mm – 1-5/8" 10mm .177 100 100050856 52mm – 2" 10mm .177 100 100050858 62mm – 2-1/2" 10mm .177 100 100050860 72mm – 2-7/8" 10mm .177 100 100050862 82mm – 3-1/4" 10mm .177 100 1000

Ballistic Point Step Shank PinsPART HEAD SHANK STD. STD.NO. SHANK LENGTH DIA. DIA. BOX CTN.50056 1-1/4" .300 .181/.150 100 500050057 1-7/8" .300 .181/.150 100 1000

10mm Head Drive PinsDS Type PinsDrive pins with an 8mm and 10mm diameter head are designed forpermanently fastening a fixture to concrete, some types of masonryand A36 structural steel. Drive pins are manufactured with a 0.177"diameter shank in various lengths.Knurled shank designs are available to increase performance in steelbase materials. A plastic washer is mounted over the point to retain thedrive pin in the fastener guide of the tool providing guidance during thedriving operation.

10mm Head Drive PinsFor P3600

PART THREAD SHANK THREAD SHANK STD. STD.NO. LENGTH LENGTH DIA. DIA. BOX CTN.50320* 1/2" 1/2" K 1/4" .145 100 500050322 3/4" 1/2" K 1/4" .145 100 100050326 3/4" 3/4" 1/4" .145 100 100050328 1/2" 1" 1/4" .145 100 100050330 3/4" 1" 1/4" .145 100 100050334* 1/2" 1-1/4" 1/4" .145 100 100050336 3/4" 1-1/4" 1/4" .145 100 100050338 1-1/4" 1-1/4" 1/4" .145 100 1000

Threaded StudsThreaded studs are available in 1/4"-20 and 3/8"-16 thread diameterswith a variety of thread and shank lengths for use in concrete, sometypes of masonry, and A36 structural steel. They are used forapplications where it may be desirable to remove the fixture, whereshimming may be required. The shank diameter for the threaded stud is 0.145" for the 1/4"-20diameter and 0.205" for the 3/8"-16 diameter. Knurled shank designsare available to increase performance in steel base materials. A plasticflute is mounted over the point to retain the drive pin in the fastenerguide of the tool providing guidance during the driving operation. Onthe 1/4"-20 threaded studs, a plastic cap is also provided to protect thethreads of the fastener during the driving process.

1/4"-20 Threaded Studs

*Discontinued item once current stock exhausted.K = Knurled

294SS 5/19/10 5:07 PM Page 294

295

Fasteners

3/8"–16 Threaded Studs

Hammer Drive® Setting Tool

Hammer Drive® PinsNo Powder Loads RequiredHammer Drive® pins are designed for permanently fastening a fixtureto concrete and some types of masonry. This fastener is designed foruse in a standard hand tool and should not be used in a powderactuated tool.

The pins are formed with a 1/4" diameter head on one end and a0.140" diameter shank in various lengths. A 3/8" diameter steelwasher is mounted over the point to retain the drive pin in the fastenerguide of the tool providing guidance during the driving operation. Thisfastener is recommended for light duty static load applications whereholding power is not a critical factor. It should not be used overhead.

1/4" Head Hammer Drive® Pins

PART HEAD SHANK STD. STD.NO. SHANK LENGTH DIA. DIA. BOX CTN.50162* 1" 3/8" .172 100 100050164* 1-1/4" 3/8" .172 100 100050166* 1-1/2" 3/8" .172 100 100050170* 2" 3/8" .172 100 100050172* 2-1/2" 3/8" .172 100 100050174* 3" 3/8" .172 100 100050176* 3-1/8" (w/step shank) 3/8" .216/.188 100 1000

3/8" Head Drive PinsDrive pins with a 3/8" diameter head are designed for permanentlyfastening a fixture to concrete, some types of masonry and A36structural steel. The pins are manufactured with a 0.172" diametershank in various lengths. A plastic flute is mounted over the pointto retain the drive pin in the fastener guide of the tool providingguidance during the driving operation.

Ceiling Clip AssembliesFor applications suspending acoustical ceiling systems or lightfixtures, several styles of angled clips are pre-mounted onto pins.

.300 Head Pins with Ceiling Clips

Assemblies & AccessoriesAssemblies are combinations of drive pins and stamped steel clipsdesigned for specific applications. The pins are held within the clipusing either a dome mechanism or a metal top hat.

PART THREAD SHANK THREAD SHANK STD. STD.NO. LENGTH LENGTH DIA. DIA. BOX CTN.50340† 1-1/4" 3/4" K 3/8" .205 100 100050342 1-1/4" 1" 3/8" .205 100 100050344† 1-1/4" 1-1/4" 3/8" .205 100 1000

PART HEAD SHANK WIRE STD. STD.NO. DESCRIPTION DIA. DIA. HOLE BOX CTN.50363†† 1" .300 .145 0.278" 100 100050364 1" .300 .145 0.278" 100 100050368† 1-1/8" .300 .145 0.278" 100 100050370 1-1/4" .300 .145 0.278" 100 1000

8mm Drive Head Pins with Ceiling Clips

10mm Drive Head Pin with Ceiling Clips

PART HEAD SHANK WIRE STD. STD.NO. DESCRIPTION DIA. DIA. HOLE BOX CTN.50272 27mm w/CC 8mm .145 0.278" 100 100050274 32mm w/CC 8mm .145 0.278" 100 1000

PART HEAD SHANK STD. STD.NO. DESCRIPTION DIA. DIA. BOX CTN.50206 1/4" with ceiling clip 10mm .177 100 1000

Ballistic Point Drive Pin with Ceiling ClipPART HEAD SHANK STD. STD.NO. DESCRIPTION DIA. DIA. BOX CTN.50058 1-1/4" with ceiling clip .300 .181/.150 100 1000

K = Knurled† Factory Mutual Research Corp. approved for Pipe Hanger Components

† Economy Clip†† Ceiling Clip without Dome


PART HEAD SHANK STD. STD.NO. SHANK LENGTH DIA. DIA. BOX CTN.50294 3/4" 1/4" .140 100 500050296 1" 1/4" .140 100 500050298 1-1/4" 1/4" .140 100 100050302* 2" 1/4" .140 100 100050304* 2-1/2" 1/4" .140 100 100050306* 3" 1/4" .140 100 1000


PART STD. STD.NO. DESCRIPTION BOX CTN.50310 Hammer Drive® Tool - Standard 1 1

295SS 5/19/10 5:07 PM Page 295

296

Fasteners

Pre-assembled Pin and Clip for Ladd Tool (L1600)

BX and EMT Conduit Clip Assemblies

For the electrical trade, BX and EMT conduit clips are provided invarious sizes for attaching conduit to base materials.

.300 Head Drive Pins with BX Cable Clips

.300 Head Drive Pins with EMT Conduit Clips

PART HEAD SHANK WIRE STD. STD.NO. DESCRIPTION DIA. DIA. HOLE BOX CTN.50438 Pre-assembled .310 .155 0.278" 100 1000

Pin Clip

PART HEAD SHANK STD. STD.NO. DESCRIPTION DIA. DIA. BOX CTN.50150 1" (BX) .300 .145 100 100050152 1-1/4" (BX) .300 .145 100 1000

PART HEAD SHANK STD. STD.NO. DESCRIPTION DIA. DIA. BOX CTN.50380* 1/2" EMT 1-1/4" .300 .145 100 100050382 1/2" EMT 1" pin .300 .145 100 100050384 3/4" EMT 1-1/4" .300 .145 100 100050385 3/4" EMT 1" pin TH .300 .145 100 100050386 3/4" EMT 1" pin .300 .145 100 100050388 1" EMT 1" pin TH .300 .145 25 250

PART HEAD SHANK STD. STD.NO. DESCRIPTION DIA. DIA. BOX CTN.50702 32mm w/ basket clip 8mm .145 100 50050704 37mm w/ basket clip 8mm .145 100 50050710* 47mm w/ basket clip 8mm .145 100 50050712 52mm w/ basket clip 8mm .145 100 50050716 62mm w/ basket clip 8mm .145 100 50050718 72mm w/ basket clip 8mm .145 100 500

8mm Diameter Head Drive Pins with EMT Conduit ClipsPART HEAD SHANK STD. STD.NO. DESCRIPTION DIA. DIA. BOX CTN.50276 27mm TH w/ 1/2" EMT 8mm .145 100 100050278 27mm TH w/ 3/4" EMT 8mm .145 100 50050280 27mm TH w/ 1" EMT 8mm .145 25 250

8mm Head Drive Pins with Rod Hanger Clip

Rebar Basket AssembliesRebar basket clips are typically used in highway construction andpaving applications to hold the support baskets for the reinforcingbars in place while the concrete is being poured.

8mm Head Drive Pins with Rebar Basket Clip

Forming PinFor concrete forming applications, the 1-3/4" (44mm) pin is designedfor fastening wood members up to 3/4" in thickness while the 2-1/2"(62mm) pin is designed for wood members up to 1-1/2" in thickness.The pin has a break off groove 1" from the point to allow the woodforming members to be easily removed.

PART SHANK STD. STD.NO. DESCRIPTION DIA. BOX CTN.50219 32mm (1-1/4") Pin w/ 1/4"-20 Rod Hanger .145 100 100050221 32mm (1-1/4") Pin w/ 3/8"-16 Rod Hanger .145 100 1000



PART HEAD SHANK STD. STD.NO. SHANK LENGTH DIA. DIA. BOX CTN.50789* 44mm - 1-3/4" .181 .145 100 500050790 62mm - 2-1/2" .181 .145 100 1000


296SS 5/19/10 5:07 PM Page 296

297

Fasteners

P1000™Size Range1/2" to 3" lengths, .22 caliber

Product DescriptionHammer actuated, professional grade powder actuated tool.Engineered for high reliability, low maintenance and speed. This tooluses four levels of power; grey through yellow loads (levels 1–4)and .300, 8mm head fasteners with lengths of 1/2" through 3" and1/4"–20 threaded studs.

P2201™Size Range1/2" to 3" pin lengths, .22 caliber

Product DescriptionThe P2201™ is a low velocity, single shot, .22 caliber tool which canbe used to install .300 head drive pins, 8mm head drive pins and1/4"–20 threaded studs, up to 3" in total length. The P2201™ isdesigned for maintenance or residential contractors.

Fastener AccessoriesIn addition to the assemblies, the following accessories are availablefor use with drive pins or threaded studs as indicated below.

PART STD. STD.NO. DESCRIPTION BOX CTN.50400 Ceiling Clip (no pin) 9/32"& 5/16" holes 100 100050408* 3/8"–16 thrd. coupling 100 100050416* 3/4" metal washer – 14 gauge 100 500050439* LADD Clip – No pin 100 100050365* Domed Ceiling Clip – No pin 100 100050375* Economy Ceiling Clip – No pin 100 1000


TOOL BODY PIN LENGTHPrecision Moulded Rubber 1/2" to 3" Total LengthTOOL LENGTH LOAD TYPE13" .22 CaliberTOOL WEIGHT POWER LEVEL3 lbs. Gray (1), Brown (2), Green (3), Yellow (4)PIN TYPEBallistic Point Drive Pin, .300 Head Drive Pin, 8mm Head Drive Pin, 1/4"–20Threaded Stud

TOOL BODY PIN LENGTHEngineered Plastic 1/2" to 3" Total LengthTOOL LENGTH LOAD TYPE12-1/2" .22 Caliber Crimped "A" LoadTOOL WEIGHT POWER LEVEL4.3 lbs. Gray (1), Brown (2), Green (3), Yellow (4)PIN TYPEBallistic Point Drive Pin, .300 Head Drive Pin, 8mm Head Drive Pin, 1/4"–20Threaded Stud

Technical Data

Technical Data

Remodeling ElectriciansMaintenance Telecommunications

Typical Applications

TRADE APPLICATIONDrywall Metal trackForming Concrete formsElectrical Boxes, conduit clip assembliesMechanical Duct strapsResidential Sill plates


PART STD.NO. DESCRIPTION CTN.52013 P1000 Tool 1

Selection Guide

PART STD.NO. DESCRIPTION CTN.52006 P2201 Tool 152522 Piston 152510 Nose Piece 152512 Piston Reset Pin 152007 P2201 (Blister Pack) 1

Selection Guide

Tool OperationPowder actuated tools may be used only by properly trained andlicensed operators as described in ANSI Standard A 10.3. Forcomplete tool operation details, contact your local Powers branchoffice or distributor for training.

297SS 5/19/10 5:08 PM Page 297

298

Fasteners

P35s™Size Range1/2" to 1-1/2" pin lengths, .25 caliber

Product DescriptionThe P35s™ is specially designed for acoustical and drywallcontractors. It is a low velocity, semi-automatic, tool which can be used to install .300 head drive pins, 8mm head drive pins and1/4"–20 threaded studs up to 1-1/2" in total length. The P35s™ isdesigned for high speed and repetitive volume applications. Thestandard version of the tool is supplied with a flat end piston and a full size baseplate/guide. A limited access baseplate/guideassembly is also available.

TOOL BODY PIN LENGTHPrecision Cast Aluminum 1/2" to 1-1/2" Total LengthTOOL LENGTH LOAD TYPE11-1/4" .25 Caliber in a 10 Load StripTOOL WEIGHT POWER LEVEL4.25 lbs. Green (3), Yellow (4), Red (5)PIN TYPEBallistic Point Drive Pin, .300 Head Drive Pin, 8mm Head Drive Pin, 1/4"–20Threaded Stud

Technical Data


TRADE APPLICATIONAcoustical Ceiling clip assembliesDrywall Metal track, door framesElectrical Boxes, conduit clip assembliesMechanical Duct straps


PART STD.NO. DESCRIPTION CTN.52002 P35s Tool (Deluxe Kit) 152023 P35s Tool (Blister Pack) 152200 Piston Standard 21/SDF 152204 Guide 21/F3-1 152206 Baseplate 21/S1 1

Selection Guide

P7201™Size Range1/2" to 1-1/2" pin lengths, .22 caliber

Product DescriptionThe P7201 is a low velocity, single shot .22 caliber tool which can be used to install .300" head drive pins, 8mm head drive pins and1/4"–20 threaded studs up to 1-1/2" in total length. The P7201 iscommonly used in the drywall trade.

TOOL BODY PIN LENGTHPrecision Cast Aluminum 1/2" to 1-1/2" Total LengthTOOL LENGTH LOAD TYPE13-1/2" .22 Caliber Crimped "A" LoadTOOL WEIGHT POWER LEVEL4.3 lbs. Gray (1), Brown (2), Green (3), Yellow (4)PIN TYPEBallistic Point Drive Pin, .300 Head Drive Pin, 8mm Head Drive Pin, 1/4"–20Threaded Stud

Technical Data

TRADE APPLICATIONAcoustical Ceiling clip assembliesDrywall Metal trackElectrical Boxes, conduit clip assembliesMechanical Duct straps


PART STD.NO. DESCRIPTION CTN.52004 P7201 Tool (Deluxe Kit) 152005 P7201 Tool (Blister pack) 152300 Piston 152306 Barrel Extension 5/16" 152308 Barrel Stop Pin 1

Selection Guide

PART STD.NO. DESCRIPTION CTN.50065 6' Di-Electric Pole Tool 150066 8' Di-Electric Pole Tool 152041 6' Smacker Pole Tool (extension available) 1

Pole Tools for Overhead Attachments

298SS 5/19/10 5:08 PM Page 298

299

Fasteners

P3500™Size Range1/2" to 3" pin lengths, .27 caliberProduct DescriptionThe P3500™ is a low velocity, semi-automatic .27 caliber tool whichcan be used to install .300 head drive pins, 8mm head drive pins and1/4"–20 threaded studs, up to 3" in total length. The P3500™ isdesigned for high speed and repetitive volume applications.

TOOL BODY PIN LENGTHPrecision Cast Aluminum 1/2" to 3" Total LengthTOOL LENGTH LOAD TYPE13-5/8" .27 Caliber in a 10 Load StripTOOL WEIGHT POWER LEVEL5 lbs. Brown (2), Green (3), Yellow (4), Red (5)PIN TYPEBallistic Point Drive Pin, .300 Head Drive Pin, 8mm Head Drive Pin, 1/4"–20Threaded Stud

Technical Data

TRADE APPLICATIONAcoustical Ceiling clip assembliesDrywall Metal track, door framesForming Concrete forms, basket clips, forming pinsElectrical Boxes, conduit clip assembliesMechanical Duct strapsResidential Sill plates

1 3 6Minimum Power Medium Power Maximum Power


PART STD.NO. DESCRIPTION CTN.52000 P3500 Powder Tool (Deluxe Kit) 152001 P3500 Powder Tool (Blister Pack) 152102 Piston Flat End w/ Ring 152108 Guide 2/F-3 152110 Base Plate 2/S-13 152120 Shear Clip 152112 Piston Stop 152122 Steel Annular Ball 152106 Piston Ring 1Piston for Installing 8mm Head Drive Pins 52100 Piston 2/DN-1 (for 8mm Head Drive Pins) 1For applications in tight areas, a limited access base plate/guide is available.52114 Guide 2/F-4 Limited Access 152116 Baseplate 2/F-14-1 Limited Access 1

Selection Guide

PA3500™Size Range1/2" to 3" pin lengths, .27 caliberProduct DescriptionThe PA3500™ is a modified version of the P3500 that includes apower adjuster, allowing the operator to effectively decrease thepower level of the load being used. A red load can be toned down to the level of a green.Power Adjuster Settings



TOOL BODY PIN LENGTHPrecision Cast Aluminum 1/2" to 3" Total LengthTOOL LENGTH LOAD TYPE13-5/8" .27 Caliber in a 10 Load StripTOOL WEIGHT POWER LEVEL5 lbs. Brown (2), Green (3), Yellow (4), Red (5)PIN TYPEBallistic Point Drive Pin, .300 Head Drive Pin, 8mm Head Drive Pin, 1/4"–20Threaded Stud

Technical Data



PART STD.NO. DESCRIPTION CTN.52019 PA3500 Powder Tool (Deluxe Kit) 152025 PA3500 Powder Tool (Blister Pack) 152103 PA Piston Flat End with Ring 152108 Guide 2/F-3 152110 Base Plate 2/S-13 152112 Piston Stop 152120 Shear Clip 152122 Steel Annular Ball 1Piston for Installing 8mm Head Drive Pins 52100 Piston 2/DN-1 (for 8mm Head Drive Pins) 1For applications in tight areas, a limited access base plate/guide is available.52114 Guide 2/F-4 Limited Access 152116 Baseplate 2/F-14-1 Limited Access 1

Selection Guide



299SS 5/19/10 5:08 PM Page 299

300

Fasteners

P3801™Size Range1/4” to 3/8” Threaded Studs and 3/8” Headed Drive Pins

Product DescriptionPowerful and reliable heavy-duty powder actuated tool, for installing3/8” threaded studs into concrete and steel. This tool features aneasy load ejector and has a low re-coil for greater operator comfort.The P3801 is independent of any external power source saving youtime and money.

TOOL BODY PIN LENGTHPrecision Cast Aluminum 1/2” to 3” Total LengthTOOL LENGTH LOAD TYPE14" .27 Caliber Short and LongTOOL WEIGHT POWER LEVEL7 lbs. Red (5), Purple (6)PIN TYPE1/4” to 3/8” threaded studs and 3/8” Headed Drive Pins

Technical Data


APPLICATIONHanging sprinkler pipeHeavy duty applications for steel and concreteElectricalTele-communications


PART STD.NO. DESCRIPTION CTN.52008 P3801 Tool (Deluxe Kit) 152402 Nose Piece 152404 Base Plate 152415 Shield 1/4" 152417 Shield 3/8" 152420 Piston Guide 1/4" 152422 Piston Guide 3/8" 152426 Piston w/Ring 1/4" 152428 Piston w/Ring 3/8" 1

Selection Guide

TOOL BODY PIN LENGTHPrecision Cast Aluminum 1/2” to 3” Total LengthTOOL LENGTH LOAD TYPE13-5/8" .27 Caliber in a 10 Load StripTOOL WEIGHT POWER LEVEL5 lbs. Red (5), Purple (6)PIN TYPE10mm Head Pins, 3/8" Threaded Studs, 3/8" Headed Drive Pins

Technical Data

APPLICATION2x4s to concrete or steelHanging sprinkler pipeHeavy-duty applications for steel and concreteTele-communicationsConcrete forms, basket clips, forming pinsSill plates


PART STD.NO. DESCRIPTION CTN.52010 P3600 Powder Tool (Deluxe Kit) 152510 Nose Piece 152512 Piston Reset Pin 152522 Piston 152578 Piston Ring 1

Selection Guide

P3600™Size Range1" to 3" 10mm Head Pins, 3/8" Threaded Studs, 3/8" Headed Drive Pins

Product DescriptionThe P3600™ is a powerful, heavy-duty, low velocity, semi-automatic.27 caliber tool which can be used to install 10mm head drive pins,3/8" threaded studs, and 3/8" headed drive pins. The P3600™ isdesigned for applications where more power is needed, such asattaching 2x4s to hard aggregate or steel. The tool utilizes a red orpurple .27 caliber strip.

300SS 5/19/10 5:08 PM Page 300

301

Fasteners

1 3 6Minimum Power Medium Power Maximum Power

PA351™Size Range5/8" to 1-5/8" 10 fastener magazine, .27 caliberProduct DescriptionLightweight, fully automatic powder actuated tool with 10 fastener magazine forhigh volume applications. This tool fastens up to 700 nails per hour for increasedproductivity. Easy drop in magazine for one handed operation. A power adjusterprovides variable power choices and drives a wide variety of fasteners.Power Adjuster Settings

Powder LoadsPowers offers high quality powder loads, produced by the largest manufacturerin the United States, with unsurpassed quality and reliability. Specific load typesare designed for each unique powder actuated tool. They are offered as singleunits for single shot tools and collated in groups of 10 into plastic strips or metaldiscs for semi-automatic tools.

.22 Caliber “A” Low Velocity Loads for Powers P7200, P2200, Ramset® 721 and M70, Hilti® DXE37 and DXE72

.22 Caliber Loads for Ladd Ceiling Master Tool (L1600)

TOOL BODY PIN LENGTHPrecision Cast Aluminum 5/8” to 1-5/8” Total LengthTOOL LENGTH LOAD TYPE17" .27 CaliberTOOL WEIGHT POWER LEVEL8 lbs. Brown (2), Green (3), Yellow (4), Red (5)PIN TYPE10 fastener magazine Can be converted to single shot tool

Technical Data



PART STD.NO. DESCRIPTION BOX50266 PA351 Tool (Deluxe Kit) 152133 PA351 Piston w/Ring 152135 Guide 2/F-3 152137 Base Plate 2/S-13 152141 Magazine 1

PART STD. STD. MASTERNO. DESCRIPTION BOX CTN. CTN.50500 Gray, .22A 100 5000 —50502 Brown, .22A 100 5000 240,00050504 Green, .22A 100 5000 240,00050506 Yellow, .22A 100 5000 240,000

PART STD. STD. MASTERNO. DESCRIPTION BOX CTN. CTN.50514* Green – Ladd 100 5000 240,00050516* Yellow – Ladd 100 5000 160,00050518* Red – Ladd 100 5000 240,00050520 Purple – Ladd 100 5000 —

Selection Guide

PA351 Pins8mm Head Diameter Drive Pins

PART SHANK SHANK HEAD SHANK STD. STD.NO. LENGTH (in.) LENGTH (mm) DIA. DIA. BOX CTN.50240 5/8" K 16mm 8mm .145 500 250050242 3/4" K 19mm 8mm .145 500 250050244 3/4" 19mm 8mm .145 500 250050246 7/8" 22mm 8mm .145 500 250050248 1" 27mm 8mm .145 500 250050250 1-1/4" 32mm 8mm .145 500 250050252 1-1/2" 37mm 8mm .145 500 250050254 1-5/8" 42mm 8mm .145 500 2500

K = Knurled


.25 Caliber Single Loads for Hilti® DX100, DX200PART STD. STD. MASTERNO. DESCRIPTION BOX CTN. CTN.50560* Green, .25 single 100 5000 —50562* Yellow, .25 single 100 5000 —50564* Red, .25 single 100 5000 —50566* Purple, .25 single 100 5000 —


.25 Caliber Disk Loads for Ramset® D45, D60, D60L

.25 Caliber Red Disk Loads for Ramset® Model D45

PART STD. STD. MASTERNO. DESCRIPTION BOX CTN. CTN.50530* Gray, .25 disk 100 1000 80,00050532 Brown, .25 disk 100 1000 80,00050534 Green, .25 disk 100 1000 80,00050536 Yellow, .25 disk 100 1000 80,000

PART STD. STD. MASTERNO. DESCRIPTION BOX CTN. CTN.50538 Red, .25 disk 100 1000 80,000


301SS 5/19/10 5:09 PM Page 301

302

Fasteners

.27 Caliber Single Loads for Powers P3801 and Hilti® DX400PART STD. STD. MASTERNO. DESCRIPTION BOX CTN. CTN.50582* Brown, .27 single 100 5000 —50584* Green, .27 single 100 5000 —50590* Purple, .27 single 100 5000 —

Safety Strip®

.27 Caliber Safety Strip® for Powers P3500, PA3500,PA351, P3600, Ramset® SA270, Viper, Hilti® DX350,DX36M, DX451 AND DX460The safety strip is molded in a special length to provide a visualindication that the tool is loaded.

PART STD. STD.NO. DESCRIPTION BOX CTN.50620 Brown, .27 Safety Strip® 100 100050622 Green, .27 Safety Strip® 100 100050626 Yellow, .27 Safety Strip® 100 100050630 Red, .27 Safety Strip® 100 1000


.27 Caliber Long Loads for Powers P3801, Ramset® MD380and Hilti® DX600NPART STD. STD. MASTERNO. DESCRIPTION BOX CTN. CTN.50608* Green, .27 long 100 2500 —50612 Red, .27 long 100 2500 —50614 Purple, .27 long 100 2500 80,000

.25 Caliber 10 Load Strips for Powers P35S and Hilti® DX35PART STD. STD. MASTERNO. DESCRIPTION BOX CTN. CTN.50570 Green, .25 strip 100 1000 100,00050574 Yellow, .25 strip 100 1000 100,00050578 Red, .25 strip 100 1000 100,000

PART STD. STD. MASTERNO. DESCRIPTION BOX CTN. CTN.50606 Purple, .27 strip 100 1000 80,000

Master Pack.25 Caliber 10 Load Strips PART STD. STD. MASTERNO. DESCRIPTION BOX CTN. CTN.50572 Green, .25 strip 1000 20000 200,00050576 Yellow, .25 strip 1000 20000 200,00050580 Red, .25 strip 1000 20000 200,000

Master Pack.27 Caliber 10 Load Strips

.27 Caliber 10 Load Strips for Hilti® Model DX451

PART STD. STD. MASTERNO. DESCRIPTION BOX CTN. CTN.50596* Green, .27 strip 1000 20000 120,00050600* Yellow, .27 strip 1000 20000 120,000


Master Pack.27 Caliber Strip Loads PART STD. STD.NO. DESCRIPTION BOX CTN.50624 Green, .27 Safety Strip® 1000 1000050628 Yellow, .27 Safety Strip® 1000 1000050632 Red, .27 Safety Strip® 1000 10000

Ramset® is a registered trademark of Illinois Tool Works, Inc.Hilti® is a registered trademark of Hilti, Inc.


Get on

Star SalesMailing List

Today!

We mail out promotions,product announcements, sale notices and conductproduct demonstration and instruction on a

regular basis.

302SS 5/19/10 5:09 PM Page 302

303

Fasteners

TRAK-ITPIN CATEGORY TRAK-IT C3 PINS1 C4

PRODUCT

Gas Fastening Selection Guides


Stan

dard

Pin

s(S

moo

th S

hank

with

Rol

led

Poin

t)

Stan

dard

Pin

s w

ithBr

eak-

free

Colla

tion

(Sm

ooth

Sha

nk w

ith R

olle

d Po

int)

Perm

a-Se

al C

oate

dSt

anda

rd P

ins

Plyw

ood

to S

teel

(Spi

ral

Knur

l Sha

nk w

ith R

olle

d Po

int)

Bulls

eye

Pins

(Ste

p Sh

ank

with

Rol

led

Poin

t)

Stic

k-E

Pin

(Ste

pSh

ank)

C4 P

ins

1/2"

Ste

el P

in(S

tep

Shan

k w

ith R

olle

d Po

int)

0.102"/ 0.102" 0.102" 0.102" 0.102" 0.102"/ 0.088" 0.136"Diameter (inches)

0.120" 0.120" 0.102" 0.145"

3/4"

3/4" 3/4" 11/16" 1"

1/2" 1" 1-1/4" 3/4" 3/4" 0.780" 1-1/4"Length (inches)

1-1/4" 1-1/2" 1" 1-3/8" 1" 1" 1-1/2"

1-1/2" 2-3/8"

2-1/2"

Concrete ■ ■ ■ ■ ■

High Strength Concrete/Precast Concrete

■ ■■ ■■

Lightweight Concrete ■ ■ ■ ■ ■

Lightweight Concreteon Metal Deck

■ ■ ■ ■ ■

Wood Sill Plate to Concrete ■

Grouted Concrete Masonry ■ ■ ■ ■ ■■

Hollow Concrete Masonry ■ ■ ■ ■

Brick Masonry ■■ ■■ ■■ ■■

Plywood to Lt. Gage Steel ■

Stick-E Accessories ■ ■

A36 / A572 Steel ■

Base

Mat

eria

lPi

n Di

men

sion

s

303SS 5/19/10 5:09 PM Page 303

304

Fasteners

PRODUCT

Roofing Selection Guide


DECK

SCR

EWS

Coat

ing/

Mat

eria

l

POW

ERLI

TE

PERM

A-SE

ALRO

OFIN

G SP

IKE

STRE

SS P

LATE

S

Steel Deck ■

Wood Deck ■

Concrete Deck ■

Lightweight Concrete Deck ■

Insulating Cover ■■

Cement Wood Fiber ■

Gypsum ■

1" ■ ■ ■

2" ■ ■ ■

3" ■ ■ ■

4" ■ ■ ■

5" ■ ■ ■

6" ■ ■ ■

7" ■ ■ ■

8" ■ ■

9" ■ ■

10" ■ ■

11" ■ ■

12" ■ ■

13" ■

Perma-Seal Coated Carbon Steel

■ ■

Stainless Steel ■

Galvalume ■

Engineered Plastic ■ ■

Insu

latio

n Th

ickn

ess

Base

Mat

eria

l

304SS 5/19/10 5:09 PM Page 304

305

Fasteners

SPIKE® (Perma-Seal™)Roofing AnchorBase MaterialConcreteSize Range3/16" x 1" to 1/4" x 14"Anchor MaterialPerma-Seal™ Coated Carbon Steel

For roofing applications, the SPIKE® is a one-piece, vibrationresistant anchor available in 3/16" and 1/4" diameters for use infastening insulation, single-ply membrane, wood, and metal tostructural concrete roof decks. This version of the SPIKE® has aPerma-Seal™ coating, a proprietary fluoropolymer, which meets thecorrosion resistance requirements of FMRC Standard 4470. It isdesigned for use in conjunction with Powers insulation or membranestress plates.

SPIKE® (Perma-Seal™) PowerliteRoofing AnchorBase MaterialStructural Cement Wood Fiber, Gypsum, or Lightweight ConcreteSize Range2" to 14" LengthsAnchor MaterialReinforced Engineered Nylon

The Powerlite™ is a fastener used to mechanically attach rigidinsulation board and single-ply membrane to structural cement woodfiber, gypsum, and lightweight insulating concrete roof decks. Thefastener is used in conjunction with insulation and membrane stressplates. The plates are manufactured with four barbs on the undersidethat grip the insulation board or single-ply membrane preventingrotation.

Perma-Seal™ SPIKE®

PART ANCHOR DRILL MIN. STD. STD.NO. SIZE DIA. EMBED. BOX CTN.3811 1/4" x 1-1/4 1/4" 7/8" 500 5003723 1/4" x 1-1/2" 1/4" 7/8" 500 5003725 1/4" x 2" 1/4" 1-1/4" 500 5003727 1/4" x 2-1/2" 1/4" 1-1/4" 500 5003729 1/4" x 3" 1/4" 1-1/4" 500 5003731 1/4" x 3-1/2" 1/4" 1-1/4" 500 5003733 1/4" x 4" 1/4" 1-1/4" 500 5003735 1/4" x 4-1/2" 1/4" 1-1/4" 500 5003737 1/4" x 5" 1/4" 1-1/4" 500 5003739 1/4" x 5-1/2" 1/4" 1-1/4" 500 5003741 1/4" x 6" 1/4" 1-1/4" 250 2503743 1/4" x 6-1/2" 1/4" 1-1/4" 250 2503745 1/4" x 7" 1/4" 1-1/4" 250 2503747 1/4" x 7-1/2" 1/4" 1-1/4" 250 2503749 1/4" x 8" 1/4" 1-1/4" 250 2503753 1/4" x 9" 1/4" 1-1/4" 250 2503757 1/4" x 10" 1/4" 1-1/4" 250 2503765 1/4" x 11" 1/4" 1-1/4" 100 1003769 1/4" x 12" 1/4" 1-1/4" 100 1003773 1/4" x 13" 1/4" 1-1/4" 100 1003777 1/4" x 14" 1/4" 1-1/4" 100 100

PART MIN. STD.NO. LENGTH EMBED. CTN.4670 2" 1-1/2" 5004671 2-1/2" 1-1/2" 5004669 2-3/4" 1-1/2" 5004672 3" 1-1/2" 5004673 3-1/2" 1-1/2" 5004674 4" 1-1/2" 5004675 4-1/2" 1-1/2" 5004676 5" 1-1/2" 5004677 5-1/2" 1-1/2" 5004678 6" 1-1/2" 5004679 6-1/2” 1-1/2” 5004680 7” 1-1/2” 2504681 7-1/2” 1-1/2” 2504683 8” 1-1/2” 2504684 8-1/2” 1-1/2” 2504685 9” 1-1/2” 2504686 9-1/2” 1-1/2” 2504687 10” 1-1/2” 2504688 11” 1-1/2” 2504689 12” 1-1/2” 2504691 13" 1-1/2" 2504692 14" 1-1/2" 250

SPIKE® Installation Tools for Roofing ApplicationsPART GUIDE STD.NO. SIZE I.D. BOX3790 SPIKE® Driver 1000 1/2" 13791 SPIKE® Driver 2000 1/2" 1

Powerlite™ Installation AccessoriesPART STD.NO. DESCRIPTION BOX4695 Powerlite™ Bit Tip 14696 Powerlite™ Bit Holder 1

Powerlite™ Plates (Galvalume)PART STD.NO. LENGTH CTN.3876 2" Powerlite™ Membrane Plate 5003896 3" Powerlite™ Insulation Plate 500

305SS 5/19/10 5:10 PM Page 305

306

Fasteners

Deck Screws™

Roofing AnchorBase MaterialSteel, Wood or Concrete Roof DecksSize RangeNo. 12 x 1-5/8" to No. 15 x 16"Anchor MaterialPerma-Seal™ Coated Carbon Steel

Deck Screws™ are designed for attaching rigid insulation board,single ply membrane, and wood blocking to steel and wood decks.Some sizes can also be used in concrete decks. Available sizesinclude No. 12, No. 14, and No. 15 diameters in carbon steel witheither hex washer or Phillips-style heads. The Deck Screws™ areused in conjunction with insulation or membrane plates and can alsobe used with batten bar. For corrosion protection the screws arecoated with Perma-Seal™ coating, a proprietary fluoropolymer,which meets the requirements of Factory Mutual Standard 4470.

Perma-Seal™ Coated No.12 PH Deck ScrewPART THREAD STD. STD.NO. SIZE LENGTH BOX CTN.2613 No. 12 x 1-5/8" 1-1/2" 1000 10002618 No. 12 x 2-1/4" 2" 1000 10002624 No. 12 x 2-7/8" 2-5/8" 1000 10002530 No. 12 x 3-1/4 3" 1000 10002632 No. 12 x 3-3/4" 3" 1000 10002636 No. 12 x 4-1/2" 3" 1000 10002640 No. 12 x 5" 3" 1000 10002648 No. 12 x 6" 4" 1000 10002656 No. 12 x 7" 4" 500 5002664 No. 12 x 8" 4" 500 500

Driver Bits For Deck Screws™PART STD.NO. SIZE BOX3585 No. 3 Phillips Power Bit (2") 13590 1/4" Hex Bit (1-7/8") 1

Stress Plates Base MaterialInsulation, Single-Ply Roofing MaterialsSize Range2" and 3" RoundAnchor MaterialStainless Steel or Galvalume Disc

Stress plates are designed for use with Deck Screws™ and SPIKE®

anchors. Stress plates can be grouped into two categories; insulationplates and membrane plates. Insulation plates, as the term implies,are used when mechanically attaching rigid foam insulation to roofdecks. They are manufactured in a 3" diameter for use with No. 12,No. 14, and No. 15 Deck Screws™, 3/16" and 1/4" SPIKE® anchors,and 1/4" Speed Lock Toggles. Two carbon steel plates, a Type 304stainless steel plate, disc are available. A recessed plate is availablefor use with the No. 12 hex washer head screws. For corrosionresistance, a Galvalume coating is applied to the carbon steel plates.Membrane plates, sometimes called lap plates, are used whenmechanically attaching single ply material in the area of the lap orseam. They are manufactured in a 2" diameter for use with No. 12,No. 14, and No. 15 Deck Screws™, 3/16" and 1/4" SPIKE® anchors.

Insulation Plates — For PH ScrewsPART PLATE STD.NO. SIZE THICKNESS MATERIAL CTN.3880 3" round .019" Galvalume 5003881 3" round .019" Stainless Steel 500

Membrane PlatesPART PLATE STD.NO. SIZE THICKNESS MATERIAL CTN.3878 2" round barbed .034" Galvalume 1000

Stainless Steel Sealing and Plastic WashersStainless Steel Sealing and Plastic Washers are typically used with1/4" diameter anchors for roof flashing, termination bar anddissimilar metal applications.

Sealing Washer Type 304 Stainless Steel with EPDM SealPART STD. STD.NO. SIZE BOX CTN.2896 1/4" (ID) x 1-1/8" (OD) 100 1000

Plastic WasherPART STD. STD.NO. SIZE BOX CTN.3994 1/4” (ID) x 1-1/2” (OD) Poly 1000 —

306SS 5/19/10 5:10 PM Page 306

307

Fasteners

DRYWALL SCREWSBugle Head Sharp

Multi-purpose screwused for fasteningdrywall to 20-25 gaugemetal studs. Phil. recess.

• Twin lead point for increased holding and faster penetration.• Available in Black Phosphate or Zinc Coating. (1”-3”)

Approx.Size Part No. Qty./Box Wt./Box

6 x 1 SS100 10 M 31 lbs6 x 1 1/8 SS118 10 M 32 lbs6 x 1 1/4 SS114 8 M 30 lbs6 x 1 5/8 SS158 5 M 24 lbs6 x 2 SS200 3.5 M 21 lbs6 x 2 1/4 SS214 3 M 20 lbs7 x 2 SS200X 3.5 M 23 lbs8 x 2 1/2 SS212 2.5 M 25 lbs8 x 3 SS300 2 M 23 lbs10 x 3 1/2 SS312 1.5 M 27 lbs10 x 3 3/4 SS334 1.5 M 30 lbs10 x 4 SS400 1.5 M 32 lbs10 x 4 1/2 SS412 1 M 36 lbs10 x 5 SS500 1 M 27 lbs10 x 6 SS600 1 M 29 lbs

Coarse Hi ThreadThe most complete line ofcoarse thread drywall screws.Used in many applications,wood to wood, drywall to wood,

cabinet installation, and outdoor wood decks. Phil. recess.• Available in Black Phosphate, Zinc, or Zinc Yellow Dichromate.


6 x 1 C100B 10 M 31 lbs6 x 1 1/8 C118B 10 M 32 lbs6 x 1 1/4 C114B 8 M 30 lbs6 x 1 1/2 C112B 6 M 26 lbs6 x 1 5/8 C158B 5 M 24 lbs6 x 1 3/4 C134B 4 M 21 lbs6 x 2 C200B 3.5 M 21 lbs6 x 2 1/4 C214B 3 M 20 lbs7 x 2 C200BX 3.5 M 23 lbs8 x 2 1/2 C212B 2.5 M 25 lbs8x 3 C300B 2 M 23 lbs10 x 3 1/2 C312B 1.5 M 27 lbs10 x 4 C400B 1.5 M 32 lbs10 x 4 1/2 C412B 1 M 36 lbs10 x 5 C500B 1 M 27 lbs

Wafer Lath SharpFor attaching metal lath or k-lathto metal studs 20 to 25 gauge.Zinc finish, Phil. recess.• 9/16 also available in Black

Phosphate.


8 x 9/16 W916Z 10 M 33 lbs8 x 3/4 W034Z 8 M 38 lbs8 x 1 W100Z 5 M 26 lbs8 x 1/4 W114Z 5 M 31 lbs8 x 1-5/8 W158Z 4 M 30 lbs8 x 2 W200Z 2.5 M 25 lbs

Laminating Screw

A temporary fastener for attchingdrywal to drywall. Phil. recess.


10 x 1/2 L112 5 M 38 lbs

Pan Framing SharpFor attaching steel studs to steel track up to20 gauge.• Serrations under head to prevent spinning.


6 x 7/16 SS6716 15 M 35 lbs7 x 7/16 SS7716 15 M 38 lbs

Trim Head SharpFor attaching wood trim andbase to metal studs.• Square drive.


6 x 1 TS100 10 M 30 lbs6 x 1 5/8 TS158 5 M 21 lbs6 x 2 1/4 TS214 3 M 20 lbs8 x 3 TS300 2 M 22 lbs

Accoustical Eye Lag ScrewFor hanging tie wire towood beams foracoustical ceiling andother applications.


1/4 x 3 LAG300 1 M 26 lbs1/4 x 4 LAG400 1 M 29 lbs1/4 x 5 LAG500 5 C 35 lbs

307SS 5/19/10 5:10 PM Page 307

308

Fasteners

DRYWALL SELF DRILLING SCREWSBugle Head Self-Drill

Used for fasteningdrywall to 14-20 gaugemetal studs.• Posi-Grip drill point

provides easier cuttingand faster penetration.

• Available in Black Phosphate or Zinc plated.


6 x 1 SD100 10 M 33 lbs6 x 1 1/8 SD118 10 M 34 lbs6 x 1 1/4 SD114 8 M 30 lbs6 x 1 5/8 SD158 5 M 23 lbs6 x 1 7/8 SD178 4 M 27 lbs8 x 2 3/8 SD238 3 M 24 lbs8 x 2 5/8 SD258 2.5 M 24 lbs8 x 3 SD300 2 M 25 lbs10 x 3 1/2 SD312 1 M 18.1 lbs10 x 4 SD400 .5 M 10.3 lbs

Wood Screws/Flat Square Head/Coarse Thread

For cabinet installationand other hard wood towood applications.Square drive creates

more positive driving. Type 17 point. Nibbs under head.• Phillips and square drive.• Black, Yellow Zinc or Dacro.


8 x 1 1/4 CS8114 7 M 33 lbs8 x 1 1/2 CS8112 6 M 32 lbs8 x 1 5/8 CS8158 5 M 27 lbs8 x 1 3/4 CS8134 4 M 26 lbs8 x 2 CS8200 3.5 M 25 lbs8 x 2 1/4 CS8214 3 M 21 lbs8 x 2 1/2 CS8212 2.5 M 23 lbs8 x 3 CS8300 2 M 24 lbs

Self-Piercing (Slotted) HexWasher Head Needle Point

Used in light metal assembly such aselectrical outlets, framing, and variousother sheet metal applications. Slottedhead. Zinc Plated.

• Extra sharp point for faster penetration.• Twin lead thread makes for easier installation.


8 x 1/2 HSS8012 10 M 45 lbs8 x 3/4 HSS8034 10 M 43 lbs8 x 1 HSS8100 7.5 M 37 lbs8 x 1 1/4 HSS8114 6 M 36 lbs8 x 1 1/2 HSS8112 5 M 37 lbs8 x 2 HSS8200 3 M 30 lbs10 x 1/2 HSS10012 14 M 50 lbs10 x 3/4 HSS10034 7.5 M 35 lbs10 x 1 HSS10100 5 M 34 lbs10 x 1 1/2 HSS10112 3 M 35 lbs10 x 2 HSS10200 2 M 35 lbs

Wafer Lath Self-DrillFor attaching metal lath to heavy gauge(14-20) metal studs.• Zinc plated, Phil drive.


8 x 1/2 WD012Z 10 M 41 lbs8 x 3/4 WD034Z 8 M 44 lbs8 x 1 WD100Z 5 M 29 lbs8 x 1/4 WD114Z 5 M 34 lbs8 x 5/8 WD158Z 4 M 34 lbs8 x 1 7/8 WD178Z 3.5 M 36 lbs10 x 1/2 WD10012Z 10 M 44 lbs10 x 3/4 WD10034Z 7 M 42 lbs

Cement Board Self-Drill ScrewsFor attachingcement board to14-20 gauge metalstuds. Special

exterior coating provides over 500 salt spray hours.• Self-Drill.• Type “S” point.


8 x 1 1/4 DR114 5 M 34 lbs8 x 1 5/8 DR158 4 M 35 lbs8 x 2 1/4 DR214 2 M 22 lbs8 x 1 1/4 SR114 5 M 34 lbs8 x 1 5/8 SR158 4 M 35 lbs8 x 2 1/4 SR214 2 M 22 lbs

Trim Head Self-DrillUsed for attachingwood trim or base to14-20 gauge metalstuds. Zinc coating.

• Square drive.


6 x 1 TSD100Z 10 M 30 lbs6 x 1 5/8 TSD158Z 5 M 22 lbs7 x 2 1/4 TSD7214Z 3 M 19 lbs8 x 3 TSD300Z 2 M 22 lbs

308SS 5/19/10 5:11 PM Page 308

309

Fasteners

DRYWALL SELF-DRILLINGSCREWS

Pan Framing Self-Drill

For attaching steel track to 14-20 gauge metalstuds.• Available in Black Phosphate or Zinc plated.

Phil Drive.


6 x 7/16 SD6716 15 M 35 lbs7 x 7/16 SD7716 15 M 38 lbs10 x 9/16 SD10916 10 M 49 lbs

ALL WEATHER COARSE DECK SCREWS

Dacro CoatedUse in fence, decks, wood siding,gazebos, or any exposed exteriorapplication. *Use stainless deck

screws for cedar and redwood applications.


6 x 1 C100D 10 M 31 lbs6 x 1 1/8 C118D 10 M 32 lbs6 x 1 1/4 C114D 8 M 30 lbs6 x 1 5/8 C158D 5 M 24 lbs6 x 2 C200D 3.5 M 21 lbs6 x 2 1/4 C214D 3 M 20 lbs8 x 2 1/2 C212D 2.5 M 25 lbs8 x 3 C300D 2 M 23 lbs10 x 3 1/2 C312D 1.5 M 27 lbs10 x 4 C400D 1.5 M 32 lbs10 x 5 C500D 1 M 24 lbs10 x 6 C600D 1 M 31 lbs

302 Stainless Deck Screws(Square Drive) Type 17 Pt.

For the best possible corrosion resistance use 302 stainlessdeck screws. Large diameter prevents snapping. Square driveprevents stripping of recess and provides superior drivingpower. Especially good for cedar and redwood applicationswhere Dacro coating may cause bleeding.• #2 square drive.


8 x 1 1/4 DS114 5 M 28 lbs8 x 1 5/8 DS158 4 M 29 lbs8 x 2 DS200 3 M 25 lbs10 x 2 1/2 DS212 2 M 25 lbs10 x 3 DS300 1.5 M 23 lbs10 x 3 1/2 DS312 1 M 18 lbs10 x 4 DS400 1 M 21 lbs7 x 1 5/8 TS158S 5 M 25 lbs7 x 2 1/4 TS214S 3 M 21 lbs8 x 3 TS300S 2 M 23 lbs

HI/LOW THREAD SCREWSFOR WOOD

Hi-Low Thread

For wood and light gaugemetal


6 x 1 1/4 HL114 8 M 30 lbs6 x 1 5/8 HL158 5 M 24 lbs6 x 2 1/4 HL214 3 M 20 lbs8 x 3 HL300 2 M 23 lbs

• Bugle Head

• Trim Head

• Type 17 point

Ceramic Coated Deck Screws1000 hours salt spray tested.Ceramic coating provides highercorrosion resistance. Square drive

with Type 17 point to prevent wood splits. Silver color. Nibsunder head to better lock screw.


6 x 1 1/8 C118CD 10 M 30 lbs6 x 1 1/4 CS114CD 8 M 28 lbs8 x 1 3/4 CS134CD 4 M 27.1 lbs8 x 2 CS200CD 3.5 M 26.3 lbs8 x 2 1/2 CS8212CD 2.5 M 23 lbs8 x 3 CS300CD 2 M 22.2 lbs10 x 3 1/2 CS312CD 1 M 18.1 lbs10 x 4 CS400CD 1 M 19.9 lbs

309SS 5/19/10 5:11 PM Page 309

310

Fasteners

SPECIALTY SELF-DRILL SCREWS

Phil Flat Self-Drill With WingsFor attaching wood toheavy gauge metal .

• With shank slot and wings, #4 point.• Zinc plated #3 Phil. Recess.

Approx. Max.Size Part No. Qty./Box Wt./Box Drill Cap.

12-24 x 2 FD12200 2 M 36 lbs .37512-24 x 2 1/2 FD12212 1.5 M 29 lbs .3751/4-20 x 2 3/4 FD14234 1 M 31 lbs .3751/4-20 x 3 FD14300 1 M 34 lbs .3751/4-20 x 3 1/4 FD14314 9 C 30 lbs .3751/4-20 x 3 1/2 FD14312 5 C 19 lbs .3751/4-20 x 3 3/4 FD14334 5 C 21 lbs .375

Thin Wafer Plymetal Self-DrillWith Wings

For attaching plywood to metal.*Wings prevent plywood fromclimbing up threads.• Wings bore out and relieve

wood chips before breakingoff at metal.

• Zinc plated #3 point. #2 Phil.Recess.


10-24 x 1 7/16 1024176 4 M 37 lbs .220

Thin Wafer Plymetal Self-DrillFor attaching plywood to metal with.220 max. thickness. Good for flooringand trailer bed applications.• Zinc plated #3 point. #2 Phil. Recess.


10-16 x 3/4 1016034 7 M 42 .22010-24 x 3/4 1024034 7 M 42 .22010-24 x 1 1024100 5 M 34 .22010-24 x 1 1/4 1024114 3.5 M 31 .22010-24 x 1 7/16 1024176 4 M 33 .22010-24 x 1 1/2 1024112 3 M 31 .220


8 x 3/4 WHD8034Z 7 M 46 lbs .1048 x 1 WHD8100Z 5 M 38 lbs .1048 x 1-1/4 WHD8114Z 4 M 30 lbs .1048 x 1-1/2 WHD8112Z 3.5 M 33 lbs .10410 x 3/4 WHD10034Z 5 M 42 lbs .17910 x 1 WHD10100Z 4 M 39 lbs .17910 x 1-1/4 WHD10114Z 3.5 M 35 lbs .17910 x 1-1/2 WHD10112Z 3 M 36 lbs .17912 x 3/4 WHD12034Z 3.5 M 37 lbs .22012 x 1 WHD12100Z 3 M 35 lbs .220


12 x 1-1/4 WHD12114Z 3 M 44 lbs .22012 x 1-1/2 WHD12112Z 2.5 M 37 lbs .22012 x 2 WHD12200Z 1.5 M 27 lbs .22012 x 3 WHD12300Z 1 M 26 lbs .22014 x 3/4 WHD14034Z 3 M 46 lbs .25014 x 1 WHD14100Z 2.5 M 44 lbs .25014 x 1-1/4 WHD14114Z 2 M 41 lbs .25014 x 1-1/2 WHD14112Z 2 M 46 lbs .25014 x 2 WHD14200Z 1.5 M 42 lbs .25014 x 3 WHD14300Z 1 M 38 lbs .250

METAL BUILDING SCREWSHex Washer Head Self-Drill With Bonded Washer

For attaching light gauge metal, metal siding, flashing, etc. to steel structure. Neoprene bonded sealingwasher keeps out moisture and prevents bleeding.• With preassembled Neoprene bonded sealing washer.* Zinc plated.

Hex Head Self-DrillUse a #4 point formetal to steelapplications up to3/8” thick. #5 pointfor metal to steel upto 1/2” thick.


*12-24 x 7/8 1224078 5 M 48 lbs .37512-24 x 1 1/4 1224114 4 M 48 lbs .50012-24 x 1 1/2 1224112 2 M 26 lbs .50012-24 x 2 1224200 2 M 36 lbs .500

• #4 point* • #5 point* • Zinc plated.

310SS 5/19/10 5:11 PM Page 310

311

Fasteners

SELF-DRILL ZINC PLATED SCREWS

410STAINLESS STEEL

SELF-DRILL

Approx. Max.Size Part No. Qty./Box Wt./Box Point No. Drill Cap.

6 x 1/2 HD6012 15 M 42 lbs 2 .1046 x 3/4 HD6034 10 M 35 lbs 2 .1048 x 1/2 HD8012 10 M 33 lbs 2 .1048 x 5/8 HD8058 10 M 37 lbs 2 .1048 x 3/4 HD8034 10 M 43 lbs 2 .1048 x 1 HD8100 7.5 M 38 lbs 2 .1048 x 1-1/4 HD8114 5 M 32 lbs 2 .1048 x 1-1/2 HD8112 5 M 39 lbs 2 .1048 x 2 HD8200 3 M 27 lbs 2 .104

10 x 1/2 HD10012 10 M 49 lbs 2 .11010 x 5/8 HD10058 7.5 M 44 lbs 3 .17910 x 3/4 HD10034 7 M 45 lbs 3 .17910 x 1 HD10100 5 M 37 lbs 3 .17910 x 1-1/4 HD10114 3.5 M 31 lbs 3 .17910 x 1-1/2 HD10112 3 M 33 lbs 3 .17910 x 2 HD10200 2 M 23 lbs 3 .17910 x 3 HD10300 1.5 M 25 lbs 3 .17912 x 3/4 HD12034 5 M 42 lbs 3 .22012 x 1 HD12100 3.5 M 35 lbs 3 .22012 x 1-1/4 HD12114 3.5 M 41 lbs 3 .22012 x 1-1/2 HD12112 2.5 M 33 lbs 3 .22012 x 2 HD12200 2 M 33 lbs 3 .22012 x 2-1/2 HD12212 1 M 21 lbs 3 .22012 x 3 HD12300 1 M 22 lbs 3 .22014 x 3/4 HD14034 3.5 M 43 lbs 3 .25014 x 1 HD14100 2.5 M 30 lbs 3 .25014 x 1-1/4 HD14114 2 M 35 lbs 3 .25014 x 1-1/2 HD14112 2 M 39 lbs 3 .25014 x 2 HD14200 1.5 M 36 lbs 3 .25014 x 2-1/2 HD14212 1 M 28 lbs 3 .25014 x 3 HD14300 1 M 32 lbs 3 .25014 x 4 HD14400 9 C 33 lbs 3 .25014 x 5 HD14500 5 C 28 lbs 3 .250

Approx. Max.Size Part No. Qty./Box Wt./Box Point No. Drill Cap.

6 x 3/8 PD6038 15 M 27 lbs 2 .1046 x 1/2 PD6012 15 M 31 lbs 2 .1046 x 5/8 PD6058 10 M 24 lbs 2 .1046 x 3/4 PB6034 10 M 29 lbs 2 .1046 x 1 PD6100 10 M 35 lbs 2 .1048 x 1/2 PD8012 10 M 32 lbs 2 .1048 x 5/8 PD8058 10 M 35 lbs 2 .1048 x 3/4 PD8034 10 M 38 lbs 2 .1048 x 1 PD8100 7.5 M 37 lbs 2 .1048 x 1-1/4 PD8114 5 M 29 lbs 2 .1048 x 1-1/2 PD8112 5 M 34 lbs 2 .1048 x 2 PD8200 3 M 31 lbs 2 .104

10 x 1/2 PD10012 10 M 45 lbs 2 .11010 x 5/8 PD10058 8 M 43 lbs 3 .17910 x 5/8 PD10058FH 8 M 41 lbs 3 .17910 x 3/4 PD10034 7.5 M 45 lbs 3 .17910 x 1 PD10100 5 M 38 lbs 3 .17910 x 1-1/4 PD10114 3.5 M 32 lbs 3 .17910 x 1-1/2 PD10112 3 M 28 lbs 3 .179

Hex Washer Head Self-Drill Pan Head Self-DrillAttaches back upplates, fixtures,door frames, andlathers channel tostructural studs,and metal decks upto 12 gauge.• Zinc finish.

Attaching steel strapping (bridging) orfurring channel to steel joist.• Zinc finish. Phillips recess.

Screw Min. Min. Avg. Avg.Diameter Tension Tortional Shear Pullout

6 1150 25 840 6708 1575 42 1055 705

2100 6110

2350 651496 786

2800 9212

3250 1002015 842

3850 15014

4275 1682585 910

Specifications apply to most STAR and POSI-GRIP screws.Tested in .16 gauge metal.

SELF-DRILL SCREW SPECIFICATIONS

Hex Washer HeadSelf-Drill

For exterior metal to metal applications thatrequire a high degree of corrosion resistance.

• 410 Stainless Steel• Available with preassembled stainless

Neoprene bonded sealing washer.

Available upon request.

Visit our website:

www.starsales.com

311SS 5/19/10 5:12 PM Page 311

350

Fasteners

Corrosion Resistance:Climacoat Long Life Polymer• Salt Spray Results (ASTM B117)

Driven: 1560 hours, 10% or less red rustUnDriven: 3240 hours, 10% or less red rust

Part No. Fastener Description.140" dia. Knurled Shank Master Carton Master Carton

5/16" dia. Bugle Head Quantity Weight ApplicationsGF100A 1" (25mm) 4,800 nails/ctn

(48 – 100 ct. coils) 18 lbs. Metal to Metal AttachmentGF112A 1-1/2" (38mm) 6,000 nails/ctn

(40 – 150 ct. coils) 36 lbs. Single Layer of Gypsum, Sheathing, Wood Furring and Blocking

GF200A 2" (51mm) 4,800 nails/ctn(32 – 150 ct. coils) 37 lbs. Double Layer of Gypsum

Sheathing, Wood Furring and Blocking

GF212A 2-1/2" (64mm) 2,700 nails/ctn(18 – 150 ct. coils) 26 lbs. Multi-Layers of Sheathing

and Wood BlockingGYPFAST GypFast Air Tool Kit (complete in a plastic carrying case) 10 lbs.AIR (1) GypFast Air Tool; (1) Safety Goggles; (1) Operators Manual; (2) Hex Keys; (1) OilGYPFAST GypFast Air HD Tool Kit (complete in a plastic carrying case) 10 lbs.AIR HD (1) GypFast Air HD Tool; (1) Safety Goggles; (1) Operators Manual; (2) Hex Keys; (1) Oil

Selection Chart

ASTM E330 Negative Wind Load ResultsStud Stud/

Fastener Board Type Orientation Gauge Spacing FastenerGypFast 5/8" Dens Glass® Vertical 18 24"/8" 70.9

GoldGypFast 5/8" Exterior

Gypsum Vertical 18 24"/8" 63.5Per ITS Report No. J20044629-231-02.

Fastener Comparison/PerformancePullout

Steel Gauge Avg. lbs. Avg. lbs. 20 18 16 14 Ultimate Ultimate

Fastener .036 .048 .060 .075 Tensile ShearGypFast 285 393 574 659 2041 1385S-12 self-drilling 194 327 437 930 750 1430screwsValues are in average, ultimate pounds.

• Always read operators manual for instruction on proper useand safety.

• Adjust depth sensitive nosepiece to achieve proper seating of fastener to work surface.

• Consult sheathing manufacturer’s guidelines for appropriatefastener and fastener spacing.

• Point of nail must penetrate 1/2" minimum beyond steel.

Performance Data

Part No. Description Carton (Qty)2731910 Lath Disc Magnetic Nose Piece 1LD114 Lath Disc - 1-1/4" 1000LD100 Lath Disc - 1" 1000

Accessories

Tools and Techniques

350SS 5/19/10 5:26 PM Page 350

351

Fasteners

Fully Automatic Cordless Gas Fastening System for Attaching Exterior Sheathing to Light Gauge Steel Framing

Features• Fully automatic system with 150 nail

capacity is 3-5 times faster thanscrews.

• Fast set-up and tear down... insertbattery, fuel cell and nail coil.

• Easy to use... self-contained powersource eliminates need for extensioncord, hoses and compressors.

• Aggressive, patented nail shankdesign provides high pulloutperformance.

• Contoured bugle head style provideshigh pullover (wind) resistance.

• Long life Climacoat™ finish is 10times more corrosion resistant thanelectro-zinc plating.

Approvals and Listings• ICBO ER 5380 (Plywood diaphragm)• ICBO ER 6070 (Gypsum sheathing)• 3rd Party Independent Testing

– Nail Withdrawl/Tensile Tests – Hardiplank® Report #3051160– Withdrawl Test - Report #3014672– Negative Wind Load Test – Report #J20044629-231-02

• Georgia Pacific Recognition Letter• UL Fire Resistance Ratings

– ANSI/UL 263– BX UV.V458

Product SpecificationsDimensionsWeight 8.9 lbs. (9.7 with nails)Height 13.0 inchesLength 16.0 inchesNailsLengths 1", 1-1/2", 2" and 2-1/2"Diameter .140" NominalHead Style 5/16" dia. bugle headFinish Climacoat Long Life PolymerFuel Cell Liquid Hydrocarbon (1 cell/1,000 nails)

Part No. GYPFAST

Applications• Exterior Gypsum sheathing to steel

framing• Plywood and OSB sheathing/flooring• Fiber cement panel attachment• Blocking

• Exterior walls• Windows/door bucks• Specialty exterior sheathing

attachment• Woven wire mesh or expanded metal

lath to steel framing

351SS 5/19/10 5:27 PM Page 351

352

Fasteners

Corrosion Resistance:Climacoat Long Life Polymer• Salt Spray Results (ASTM B117)

Driven: 1560 hours, 10% or less red rustUnDriven: 3240 hours, 10% or less red rust

Part No. Fastener Description.140" dia. Knurled Shank Master Carton Master Carton

5/16" dia. Bugle Head Quantity Weight ApplicationsGF100 1" (25mm) 4,800 nails/ctn

(48 – 100 ct. coils) 19 lbs. Metal to Metal Attachment5 fuel cells

GF112 1-1/2" (38mm) 6,000 nails/ctn(40 – 150 ct. coils) 37 lbs. Single Layer of Exterior,

6 fuel cells Sheathing, Wood Furring and Blocking

GF200 2" (51mm) 4,800 nails/ctn(32 – 150 ct. coils) 38 lbs. Double Layer of Gypsum

5 fuel cells Sheathing, Wood Furring and Blocking

GF212 2-1/2" (64mm) 2,700 nails/ctn(18 – 150 ct. coils) 26 lbs. Multi-Layers of Sheathing,

3 fuel cells Wood Blocking andand Dimensional Lumber

GYPFAST GypFast Cordless Coil Nailer 12 lbs.(1) Tool; (1) Safety Goggles; (1) Operators Manual

Selection Chart

ASTM E330 Negative Wind Load ResultsStud Stud/

Fastener Board Type Orientation Gauge Spacing FastenerGypFast 5/8" Dens Glass® Vertical 18 24"/8" 70.9

GoldGypFast 5/8" Exterior

Gypsum Vertical 18 24"/8" 63.5Per ITS Report No. J20044629-231-02.

Fastener Comparison/PerformancePullout

Steel Gauge Avg. lbs. Avg. lbs. 20 18 16 14 Ultimate Ultimate

Fastener .036 .048 .060 .075 Tensile ShearGypFast 285 393 574 659 2041 1385S-12 self-drilling 194 327 437 930 750 1430screwsValues are in average, ultimate pounds.

• Always read operators manual for instruction on proper useand safety.

• Adjust depth sensitive nosepiece to achieve proper seating of fastener to work surface.

• Consult sheathing manufacturer’s guidelines for appropriatefastener and fastener pattern.

• Point of nail must penetrate 1/2" minimum beyond steel.

Performance Data

Part No. Description Carton (Qty)2761910 Lath Disc Magnetic Nose Piece 1LD114 Lath Disc — 1-1/4" 1000LD100 Lath Disc — 1" 1000405176 Battery 1TFUEL Fuel Cell 127505142 Battery Charger 1

Accessories Tools and Techniques

352SS 5/19/10 5:27 PM Page 352

collated screw systems - starsales.comstarsales.com/pdf/star-sales-screws-and-fasteners.pdf ·...

Documents