CLONE Rc1 4T

INSTRUCTIONSFOR USE AND SET UP

FOUR MODELS ROLLING CODE DUPLICATOR

PLEASE READ ENTIRELY THESEINSTRUCTIONS FOR THE PROPER USE

OF THE PRODUCT!

REV 25-10-2016

The CLONE RC1 4T allows you to duplicate the following radio controls rolling code

® ® ® ®

WARNING: The CLONE RC1 4T can duplicate in the same device only one type of radio control at a time among those mentioned above. Therefore, after having learned the first button of any of the following four compatible types, the device will accept only codes of the same type for the other buttons.

This symbol indicates registered brands and designs, to exclusive possession of the relevant manufacturers.They are indicated in this document only for informational purposes to help identifying compatibility with our product

WARNINGThis procedure will delete all the recordings on the four buttons

WHEN TO USE IT?

NICE ONE NICE FLOR-S DITEC GOL V2 PHOENIX

Before a new reprogramming, is necessary to reset the CLONE RC1 4T

At the same time press the buttons 1 and 2

After two seconds, the led flashes three times then turns off

The led flashes again three times: the CLONE RC1 4T is reset

1 - RESET

2 - SET UP

By holding firmly down the botton 1, leaving the botton 2, then press the botton 2 three times

Press the botton CLONE RC1 4T to program

The led flashes three times and then turns off

Continue

Led, flashes three times then when in turns on, begins to vibrate:SET UP SUCCEEDED

Led flashes six times then turns off: SET UP FAILEDRepeat the procedure

By holding firmly down the botton CLONE RC1 4T to program, bring the original radio control and press the botton you want to learn

HOW TO PROGRAM IT?

®

WARNING: Some receivers, such as the most recent of the V2 ELECTRONICS, may have activated the Anticlone function, in this case the use on the same receiving of the copy and of the original , reset both codes and blocking the remote concerned controls, before using the copied remote control, verify with the installer / maintainer of the system that these functions are not activated. The Silisystem Technology srl, declines all responsibility for any malfunction of the installation that may result from use of the CLONE RC1 4T.

After duplicating the CLONE RC1 4T is usually already functioning without additional learning procedures on the receiver. In cases where you need to make learning on the receiver, for the procedures, referring to the corresponding producers’ manuals.

PLEASE NOTE: In some cases, the simultaneous use of the copy and the of original may be required to operate several times for the actuation of receiver the “off” button (code resynchronization)

Repeat the procedure for the other bottons if it is necessary.

HOW TO PROGRAM IT? continue

This model NOT NEED any calibration.

HOW TO SET UP THE FREQUENCY?

By using a phillips head screwdriver, unscrew the screw at the back of the CLONE RC1 4T remote control..

The remote control is powered by a 3V LITHIUM BATTERY with initials CR2032

Remove a dead battery and insert the new one paying attention to the correct polarity.

HOW TO REPLACE THE BATTERY?

WARNING: Do not disperse the old battery into the environment, but dispose it in dedicated waste container.

CLONE Rc1 4TFOUR MODELS ROLLING CODE DUPLICATOR

REV

25-10

-201

6

Product designed and manufactured in Italy by

SILISYSTEM TECHNOLOGY s.r.l.Via Marconi, 38 - 81030 Sant’Arpino (CE)info@silisystem.com - www.silisystem.com

CLONE Rc1 4TFOUR MODELS ROLLING CODE DUPLICATOR

CONFORMITY DECLARATION

The CLONE RC1 4T radio control complies with the essential requirements of the following standards:

ETSI EN300 220-2 Short Range Device (SRD)EN 301 489-1 Electromagnetic Compatibility (EMC)

EN60950 Safety

With the current “SILISYSTEM TECHNOLOGY srl” declares that:The device “CLONE RC1 4T” has been proved in a typical configuration of installation and complies

with the essential requirements and the other relevant provisions laid down by Directive:

1999/5/CE (R&TTE Directive)CE/108/2004 (EMC Directive)CE/95/2006 (LVD Directive)

Andrea D'AliaSant Arpino (CE) 05/20/2015

Transmission frequency European Market: 433.92 MHz