classification of explosives fourth revision · 2019. 7. 10. · ex2008120360 oot-aprv-055 igniter...

U.S. Department East Building, PHH – 32

of Transportation 1200 New Jersey Avenue, Southeast

Washington, D.C. 20590

Pipeline and Hazardous The US Department of Transportation

Materials Safety Administration Competent Authority for the United States

Tracking No: 2019054336 of 1

CLASSIFICATION OF EXPLOSIVES

FOURTH REVISION

Based upon a request by Owen Oil Tools c/o Owen Compliance Services, 12001 County

Road 1000, Godley, TX 76044, US, the following items are classed in accordance with

Section 173.56, Title 49, Code of Federal Regulations (49 CFR). A copy of your

application, all supporting documentation and a copy of this approval must be retained

and made available to DOT upon request.

An EX approval is non-transferable in any merger, acquisition, sale of assets, or other

business transaction. For more information, please visit:

[https://www.phmsa.dot.gov/registration/faq-mergers-acquisitions-and-legal-status-

changes-pdf]

U.N. PROPER SHIPPING NAME AND NUMBER:

Igniters, UN0454

U.N. CLASSIFICATION CODE: 1.4S

REFERENCE NUMBER: PRODUCT DESIGNATION/PART NUMBER:

EX2008120360 OOT-APRV-055 Igniter Family (D/N: OOT-

APRV-055A, Rev. 3): Type A (Power Charge

Igniters), Type B (Core Load Igniters), Type C

(Power Charge Igniters), Type D (Swing Jet

Release), Type E (Power Charge Igniters)

NOTES: This classification is only valid when the igniters are packaged as follows:

Inner Packaging - Boxes, chipboard, each containing one (1) igniter.

Outer Packaging - UN 4G fiberboard box, each containing not more than fifty (50) inner

packagings uniformly segregated from one another and the box sidewalls by not less than

three layers of corrugated fiberboard divider pieces and with top and bottom fiberboard

pads.

This approval as revised supersedes all previous versions.

DATED: July 10, 2019

for William Schoonover

Associate Administrator for Hazardous Materials Safety

dboston

Sticky Note

Rev. 4 adds Type E and updates drawing reference ot -055A, Rev. 3.

A

A

B

B

C

C

D

D

PLUGIGNITION MIX

RESISTOR

LEAD WIRES

O-RING SEAL

PROPELLANTFFFFG BLACK POWDER

NEEDLE

RUBBER STOPPER BODY CAP

CRIMP CONNECTOR RESISTOR

EPOXYLEAD WIRE

END CAP & EPOXY

IGNITION HOUSING

SPRING HOUSING

CONTACT PIN

TOP INSULATOR

SPRINGRESISTOR

HEAT SHRINK

IGNITION MIXTEFLON TUBING

INSULATING WASHER

END CAP & EPOXY

IGNITION MIXRESISTORPLASTIC INSULATOR

SPRING CONTACT

GROUND WIRE

BODY

TYPE C, Power Charge Igniter≤ 2.8

≤ 2.8

≤ 3.3

0.05g BP OR 0.05g BKNO3 (50/50 OR 25/75 MIXTURE) OR

0.05g BP & TSPP

TYPE A, Power Charge Igniter≤ 2.8

≤ 2.8

≤ 3.3


0.05g BP & TSPP

TYPE B, Core Load Igniter≤ 0.6 0.05g BP & #800 propellant

TYPE D, Swing Jet Release≤ 0.26 0.05g BP

NOTES:BP = Black PowderBKNO3 = Boron Potassium Nitrate TSPP = Titanium Sub-Hydride Potassium Perchlorate

* SEE SHEET 2 OF 2 FORTYPE E, POWER CHARGE IGNITER

03 ADDED OPTION E (PAGE 2 OF 2) 2/25/2019 RS

02 ADDED BKNO3 OPTION TO TYPE A & C 3/2/2015 BP

01 ADDED TYPE D 8/2/2013 DWBREV DESCRIPTION DATE (M/D/Y) INITIAL

Packaging, Marking, and Labeling

Packaging: As shown in drawing OOT-APRV-055B

Marking: Igniters, UN0454

Hazard Label: 1.4S

Consult OCS for any variations

TITLE:

PART / DRAWING: REV.

DESIGNED:

DATE (M/D/Y):

DATE (M/D/Y):

MATERIAL:

HEAT TREATMENT:

TOLERANCES UNLESS OTHERWISE NOTED: OWEN OIL TOOLS LPA CORE LABORATORIES COMPANY12001 COUNTY ROAD 1000GODLEY, TEXAS 76044

OWEN OIL TOOLS, CANADIAN DIVISIONA DIVISION OF CORE LABORATORIESCANADA LTD.5405-39139 HWY. 2ARED DEER, COUNTYALBERTA, CANADA, T4S 2B3

DRAFTED:

DO NOT SCALE DRAWING SHEET 1 OF 2

PROTECTIVE FINISH:

2/25/2019

N/AN/A

R. SEARLES

ALL DIMENSIONS IN INCHESBREAK EDGES 0.015 X 45CONCENTRICITY 0.005 TIRMAX SURFACE FINISH 125 RMS ANGULAR DIMENSIONS 0.5MIN RADIUS 0.010

.X = 0.030

.XX = 0.015.XXX = 0.005

OES-1000-100TRACEABILITY:

03

THIS TECHNOLOGY IS REGULATED BY AND, IF EXPORTED, WAS EXPORTED FROM THE UNITED STATES IN ACCORDANCE WITH THE EXPORT

ADMINISTRATION REGULATIONS (EAR). DIVERSION CONTRARY TO U.S. LAW IS PROHIBITED. EXPORT AND/OR RE-EXPORT OF THIS TECHNOLOGY MAY

REQUIRE ISSUANCE OF A LICENSE BY THE BUREAU OF INDUSTRY AND SECURITY (BIS), U.S. DEPARTMENT OF COMMERCE. CONSULT THE BIS, THE

EAR, AND/OR OWEN COMPLIANCE SERVICES, INC. TO DETERMINE LICENSING REQUIREMENTS FOR EXPORT OR RE-EXPORT OF THIS TECHNOLOGY.

NOTICE: EXPORT OF TECHNOLOGYTHIS DRAWING AND ACCOMPANYING INFORMATION IS THE

CONFIDENTIAL PROPERTY OF OWEN OIL TOOLS AND MAY NOT BE COPIED, REPRODUCED, TRANSMITTED OR DISCLOSED IN ANY

MANNER WITHOUT EXPRESS WRITTEN CONSENT AND IS TO BE RETURNED UPON REQUEST. ALL RIGHTS IN PROPRIETARY,

COPYRIGHT AND NOVEL FEATURES OF THE SUBJECT MATTERARE EXPRESSLY RESERVED. RECIPIENTS AGREEMENT TO THE

FOREGOING IS INDICATED BY ACCEPTANCE OF THIS DOCUMENT.

NOTICE: PROPRIETARY RIGHTS INVOLVED

OEF-4010-001 (R00)

OWEN OIL TOOLSOOT-APRV-055IGNITER FAMILY

N/A

OOT-APRV-055A

EE

GROUND WIRE

SPRING CONTACT

INSULATOR MOLDING GROUNDING SLEEVERESISTOR

RESISTOR IGNITION MIX

END SEAL & ADHESIVE

BRIDGEWIRE

BODY

INSULATOR

TYPE E, Power Charge Igniter≤ 2.0

≤ 2.0

≤ 2.4


0.05g BP & TSPP

DESCRIPTION:


DESIGNED:

DATE (M/D/Y):

DATE (M/D/Y):

MATERIAL:

HEAT TREATMENT:



DRAFTED:


PROTECTIVE FINISH:

2/26/2019R. SEARLES


.X = 0.030

.XX = 0.015.XXX = 0.005


03











OEF-4010-001 (R00)

TOOL:

OOT-APRV-055A






Tracking No: 2019054336 Page 1 of 1


FOURTH REVISION

Based upon a request by Owen Oil Tools c/o Owen Compliance Services, 12001 County

Road 1000, Godley, TX 76044, US, the following items are classed in accordance with




An EX approval is non-transferable in any merger, acquisition, sale of assets, or other

business transaction. For more information, please visit:

[https://www.phmsa.dot.gov/registration/faq-mergers-acquisitions-and-legal-status-

changes-pdf]


Igniters, UN0454


REFERENCE NUMBER: PRODUCT DESIGNATION/PART NUMBER:


APRV-055A, Rev. 3): Type A (Power Charge

Igniters), Type B (Core Load Igniters), Type C

(Power Charge Igniters), Type D (Swing Jet

Release), Type E (Power Charge Igniters)


Inner Packaging - Boxes, chipboard, each containing one (1) igniter.

Outer Packaging - UN 4G fiberboard box, each containing not more than fifty (50) inner

packagings uniformly segregated from one another and the box sidewalls by not less than

three layers of corrugated fiberboard divider pieces and with top and bottom fiberboard

pads.


DATED: July 10, 2019

for William Schoonover









THIRD REVISION

Based upon a request by Owen Oil Tools c/o Owen Compliance Services, P.O. Box 765,

Godley, TX 76044, United States, the following items are classed in accordance with





Igniters, UN0454


REFERENCE NUMBER PRODUCT DESIGNATION/PART NUMBER


APRV-055A, Rev. 2): Type A (Power

Charge Igniters), Type B (Core Load Igniters),

Type C (Power Charge Igniters), Type D (Swing Jet

Release)


Inner Packaging - Boxes, chipboard, each containing one (1) igniter. Outer Packaging -

UN4G fiberboard box, each containing not more than fifty (50) inner packagings

uniformly segregated from one another and the box sidewalls by not less than three layers

of corrugated fiberboard divider pieces and with top and bottom fiberboard pads.


DATED: 09/16/2015

For Dr. Magdy El-Sibaie


dboston

Sticky Note

Rev. 3 adds BKNO3 (by way of reference to drawing -055A, Rev. 2) as authorized material in Types A and C.

dboston

Void

dboston

Void

This page is intentionally blank to facilitate 2-sided printing

A

A

B

B

C

C

D

D

PLUGIGNITION MIX

RESISTOR

LEAD WIRES

O-RING SEAL

PROPELLANTFFFFG BLACK POWDER

NEEDLE

RUBBER STOPPER BODY CAP

CRIMP CONNECTOR RESISTOR

EPOXYLEAD WIRE

END CAP & EPOXY

IGNITION HOUSING

SPRING HOUSING

CONTACT PIN

TOP INSULATOR

SPRINGRESISTOR

HEAT SHRINK

IGNITION MIXTEFLON TUBING

INSULATING WASHER

END CAP & EPOXY

IGNITION MIXRESISTORPLASTIC INSULATOR

SPRING CONTACT

GROUND WIRE

BODY

TYPE C, Power Charge Igniter≤ 2.8 0.05g BP

OR≤ 2.8 0.05g BKNO3 (50/50 OR 25/75 MIXTURE)

OR≤ 3.3 0.05g BP & TSPP

TYPE A, Power Charge Igniter≤ 2.8 0.05g BP

OR≤ 2.8 0.05g BKNO3 (50/50 OR 25/75 MIXTURE)

OR≤ 3.3 0.05g BP & TSPP

TYPE B, Core Load Igniter≤ 0.6 0.05g BP & #800 propellant

TYPE D, Swing Jet Release≤ 0.26 0.05g BP

NOTES:BP = Black PowderBKNO3 = Boron Potassium NitrateTSPP = Titanium Sub-Hydride Potassium Perchlorate

02 ADDED BKNO3 OPTION TO TYPE A & C 3/2/2015 BP

01 ADDED TYPE D 8/2/2013 DWBREV DESCRIPTION DATE (M/D/Y) INITIAL

Packaging, Marking, and Labeling

Packaging: As shown in drawing OOT-APRV-055B

Marking: Igniters, UN0454

Hazard Label: 1.4S

Consult OCS for any variations

TITLE:


DESIGNED:

DATE (M/D/Y):

DATE (M/D/Y):

MATERIAL:

HEAT TREATMENT:



DRAFTED:


PROTECTIVE FINISH:

3/2/2015

N/AN/A

B. POTTER


.X = 0.030

.XX = 0.015.XXX = 0.005


02











OEF-4010-001 (R00)

OWEN OIL TOOLSOOT-APRV-055IGNITER FAMILY

N/A

OOT-APRV-055A

dboston

Void

dboston

Void

dboston

Void

dboston

Void








SECOND REVISION

Based upon a request by Owen Oil Tools c/o Owen Compliance Services, P.O. Box 765,

Godley, TX 76044, United States the following items are classed in accordance with





Igniters, UN0454



EX2008120360 OOT-APRV-055 Igniter Family: Type A (Power

Charge Igniters), Type B (Core Load Igniters),

Type C (Power Charge Igniters), Type D (Swing Jet

Release)


Inner Packaging - Boxes, chipboard, each containing one (1) igniter. Outer Packaging -

UN4G fiberboard box, each containing not more than fifty (50) inner packagings

uniformly segregated from one another and the box sidewalls by not less than three layers

of corrugated fiberboard divider pieces and with top and bottom fiberboard pads.


DATED: 04/30/2014



Dave

Sticky Note

2nd Revision adds Type D (Swing Jet Release) to the EX.

dboston

Void

dboston

Void








FIRST REVISION

Based upon a request by Owen Oil Tools, P.O. Box 765, Godley, TX 76044, United

States the following items are classed in accordance with Section 173.56, Title 49, Code

of Federal Regulations (49 CFR). A copy of your application, all supporting

documentation and a copy of this approval must be retained and made available to DOT

upon request.


Igniters, UN0454



EX2008120360 OOT-APRV-055 Owen Oil Tools Igniter Family:

Type A (Power Charge Igniters), Type B (Core

Load Igniters), Type C (Power Charge Igniters)


Inner Packaging - Boxes, chipboard, each containing one igniter. Outer Packaging - UN

4G fiberboard box, each containing not more than fifty (50) inner packagings uniformly

segregated from one another and the box sidewalls by not less than three layers of

corrugated fiberboard divider pieces and with top and bottom fiberboard pads. This

approval as revised supersedes all previous versions.

DATED: 09/22/2011



David Boston

Sticky Note

1st Revision corrects invalid family ID number that appeared in original EX.

Dave

Void








Based upon a request by Owen Oil Tools, P.O. Box 765, 12001 County Road 1000,

Godley, TX 76044, the following items are classed in accordance with Section 173.56,

Title 49, Code of Federal Regulations (49 CFR). A copy of the application, all

supporting documentation, and a copy of this Classification must be retained and made

available to DOT upon request.


Igniters, UN0454



EX2008120360 OOT-APRV 055A Owen Oil Tools Igniter Family:

Type A (Power Charge Igniters), Type B (Core

Load Igniters), Type C (Power Charge Igniters)


Inner Packaging - Boxes, chipboard, each containing one igniter. Outer Packaging - UN

4G fiberboard box, each containing not more than fifty (50) inner packagings uniformly

segregated from one another and the box sidewalls by not less that three layers of

corrugated fiberboard divider pieces and with top and bottom fiberboard pads.

DATED: 04/01/2009

For Theodore L. Willke


David Boston

Text Box

Shown is the drawing number of the product family. The product family number is "OOT-APRV-055".

David Boston

Line

David Boston

Text Box

David Boston

DWB Initials

David Boston

Void

classification of explosives fourth revision · 2019. 7. 10. · ex2008120360 oot-aprv-055 igniter...

Documents