cisco certified network associate (ccna) wireless

11
1 Cisco Certified Network Associate (CCNA) Wireless Students Lab Manual Developed by: NETWORK EXPERT INC.

Upload: others

Post on 04-Feb-2022

28 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: Cisco Certified Network Associate (CCNA) Wireless

1

Cisco Certified Network Associate (CCNA)

Wireless

Students Lab Manual

Developed by: NETWORK EXPERT INC.

Page 2: Cisco Certified Network Associate (CCNA) Wireless

2

Table of Contents

Lab#1 Password Recovery on AP 1131

Lab#2 Upgrading AP 1131 to LWAPP Mode

Lab#3 Setting up AP as Bridge

Lab#5 Installing Windows Server.

Lab#6 Configure DHCP Server on Windows for LWAPP Options

Lab#7 Configure IIS & CA Server on Windows Server

Lab#8 Install the RADIUS Server and Request a Certificate

Lab#9 Configure the RADIUS Server for PEAP-MS-CHAP v2 Authentication

Lab#10 Add User to AD and Allow Wireless Access for the User

Lab#11 Create Wireless LAN, VLANS, Interfaces in the WLC and configure WLC for RADIUS Authentication Lab#12 Setup Windows7 for Wireless Connectivity

Lab#13 Configure 3750 Switch for Connectivity

Lab#14 Configure Router to Perform NAT to reach the Internet

Lab#15 Upgrade Code on Wireless LAN Controller

Page 3: Cisco Certified Network Associate (CCNA) Wireless

3

Lab 2: Upgrading AP 1131 to LWAPP Mode

Step 1:

Install the upgrade tool on your system provide by your instructor. Or check if tool is already installed on

your laptop.

Step 2:

Open the upgrade toll by clicking on its link:

Step 3:

The IP File field is the input file of access points to upgrade. Whether you have one or several access points to upgrade, create a flat text file in the following format: ap-ip-address,telnet-username,telnet-user-password,enable-password ap-ip-address,telnet-username,telnet-user-password,enable-password Each line in the text file lists the unit IP address, Telnet username and password, and a password that permits access to the access point CLI privileged EXEC mode. Use a comma to separate each item on a line. Save the text file on the same machine that hosts the upgrade tool. Click the . . . button to browse to and select the text file.

Page 4: Cisco Certified Network Associate (CCNA) Wireless

4

Step 4:

Make the AP ready to communicate to the Upgrade tool:

Page 5: Cisco Certified Network Associate (CCNA) Wireless

5

ap(config)#username network password cisco

ap(config)#int fastEthernet 0

ap(config-if)#ip address 172.16.1.10 255.255.255.0

ap(config-if)#no shut

ap(config)#int BVI1

ap(config-if)#ip address 172.16.1.15 255.255.255.0

ap(config-if)#no shut

ap(config)#line vty 0 4

ap(config-line)#pass

ap(config-line)#password cisco

ap(config-line)#login

ap(config-line)#end

ap#wr

Assign IP to your laptop as below:

Ethernet adapter Local Area Connection:

IPv4 Address. . . . . . . . . . . : 172.16.1.20

Subnet Mask . . . . . . . . . . . : 255.255.255.0

Default Gateway . . . . . . . . . :

Test connectivity between Laptop where Upgrade tool is installed and AP:

C:\Users\ms041m>ping 192.168.5.5

Pinging 192.168.5.5 with 32 bytes of data:

Reply from 192.168.5.5: bytes=32 time=1ms TTL=255

Reply from 192.168.5.5: bytes=32 time<1ms TTL=255

Page 6: Cisco Certified Network Associate (CCNA) Wireless

6

Reply from 192.168.5.5: bytes=32 time<1ms TTL=255

Reply from 192.168.5.5: bytes=32 time<1ms TTL=255

Ping statistics for 192.168.5.5:

Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),

Approximate round trip times in milli-seconds:

Minimum = 0ms, Maximum = 1ms, Average = 0ms

C:\Users\ms041m>

Access the Wireless LAN Controller using its Service Port which has 192.168.1.1 IP by default, assign your laptop NIC 192.168.1.10 for the time being to connect to WLC to check its settings:

Uername: Administrator

Page 7: Cisco Certified Network Associate (CCNA) Wireless

7

Password: cisco123

And under Controller and Interfaces look like this:

Provide all the info in the Upgrade Tool. You will need image to upgrade AP to LWAPP mode.

Page 8: Cisco Certified Network Associate (CCNA) Wireless

8

And Tool will start upgrading the AP:

Page 9: Cisco Certified Network Associate (CCNA) Wireless

9

Page 10: Cisco Certified Network Associate (CCNA) Wireless

10

Detailed Log from the Upgrade tool will show similar to this:

As after restart AP will be in LWAPP mode and its FastEthernet Interface will be setup to look for IP from DHCP Server, haveDHCP Scope configured on the WLC:

Page 11: Cisco Certified Network Associate (CCNA) Wireless

11

Restart the LWAPP and as soon as it restarts it will get IP from the DHCP Scope from the WLC and will attempt to register with WLC and as soon as it registers, it will check and if its existing code is not matching with the code on WLC it will upgrade with the code on WLC: