chem awareness training
DESCRIPTION
Book on chemical awareness trainingTRANSCRIPT
CHEMTURACHEMICAL AWARENESS TRAINING MODULE
NAME: Mo SalihSIGN:
INTRODUCTION
The Chemtura chemical awareness module is designed to give the reader a broad view of the types of chemicals that are dealt with on site, the raw materials through to the finished products. The idea being that once the module is completed the reader will have a good understanding of the types of chemicals that Chemtura deal with, their chemical properties, hazard signs as well as knowledge of health and safety implications regarding all of the chemicals. The module is split into two parts the first being the raw materials and the second being the finished products. The task for the reader is to work through the module and find the information for each chemical on site. Each section has sub-headings down the left of the page (e.g. physical properties, hazards, handling and storage etc). There is a blank space next to each heading for the reader to fill in the information needed as well as empty boxes at the beginning and end of each section, the first set of empty boxes is for the hazard signs specific to each chemical. The second set is for the personal protection equipment needed in the handling of the specific chemical.In addition to this there are 6 diagrams of each of the tank farms that exist on site, each tank is labelled with numbers which relate to certain chemicals. It is the objective of the reader to find out what chemicals are stored on each tank farm and write that information on the diagrams.
ContentsPPE and Hazard Symbols4Tank farms5Acrylic acid10Amps13Caustic soda15Cresol/xylenol19Ethyl acrylate23HCI29Maleic anhydride 32DTBP35Propylene 39Vinyle acetate 43Phenol 47Alkylated phenol52Aluminium chloride 56Calcium hydroxide 59Carbon62Magnsium chloride 66Phosphorous oxychloride 70Sodium hypophosphite 75Sodium per sulphate79Reofos finished products83Water Additives finished products88PPE and Hazard Symbols
Safety goggles Full face visor -
Rubber work boots Gloves
Full Chemical Suit - Particle face mask
Respirator Protective apron -
Date Printed: 13 September 2012
61
TANKSCHEMICALTANKSCHEMICAL
T410T441
T408T442
T406T445
T404T449
T440TR446
T443TR448
T444TR451
T447T450
T402
Acrylic Acid
Physical properties Liquid Colourless Pungent odour
Hazards :Human :Respiratory irritation and harmful if swallowed/ inhaled.
Environment:Very toxic to aquatic life
Over exposure: Coughing, stomach pains, skin irritation, blisters and redness. Eye watering and redness
Skin: Causes severe skin burns
Eyes: Causes Eye damage
Handling and storage:
Handling: Put on PPE. Eating/drinking/smoking is prohibited in areas where they are handled/stored/processed. Workers wash hands and face before eating, drinking and smoking. Do not breath ingest or release to environment.
Storage:Store between 15 25C. Store in dry, cool, well ventilated area away for exposure to direct sunlight. Keep away from oxidising materials. Keep container tightly closed and sealed. Containers that have been opened must be carefully resealed and kept upright to prevent leakage
First Aid MeasuresInhalation:Get immediate medical attention and move exposed person to fresh air. Wear a mask and keep the exposed person warm and at rest. Provide artificial respiration by trained personal if not breathing normally. If unconscious, place in recovery position and seek medical attention. Maintain open airway on exposed person.
Ingestion:Get immediate medical attention. Wash mouth with water and remove dentures if any. Keep the exposed person warm and at rest. If conscious, give small quantities of water to drink. Stop if person feels sick as vomiting can be dangerous. Keep head low if vomiting occurs. If unconscious, place in recovery position and seek medical attention. Maintain open airway on exposed person.Skin contact: Get medical attention immediately. Flush contaminated skin with plenty of water. Flush contaminated clothing with water before removing it. Rinse skin for 10 minutes. Chemical burns must be treated promptly by a physician. Wash clothing before reuse. Clean shoes thoroughly before reuse.
Eye contact:Get medical attention immediately. Flush eyes with plenty of water while moving upper and lower eyelids. Remove contact lenses and continue to rinse for 10 minutes.Accidental Release Measures
Personal precautions:Evacuate surrounding areas, keep unprotected personal from entering. Do not touch/walk through spilled material. Provide adequate ventilation and wear appropriate respirator if ventilation inadequate. Put on PPE and shut off all ignition sources. No smoking and do not breathe mist
Environmental precautions: Avoid dispersal of spilled material and run off and contact with soil/waterways/drains/sewers. Inform authorities if environmentally exposed. Water pollutant and may be harmful to environment if released in large quantities.
Mandatory PPE Air fed respirator Chemical resistant gloves should be worn at all times. Safety eyewear to be worn at all times PPE covering the body
Amps (Acrylamido methyl propane sulphonic)
Physical Properties:
Clear/ light yellow liquid Mild OdourHazards:
Handling and storage: Keep containers closed when not in use. Minimum transport and handling temperature is 5 deg F (-15 deg C). Wash thoroughly after handling. Empty container contains product residue which may exhibit hazards of product. Dispose of packaging or containers in accordance with regulations.
Minimum storage temperature is 32 deg F (0 deg C). Maintain inhibitor and dissolved oxygen level. Stainless steel is the recommended material of the construction for storage vessels and handling equipment. Avoid contact with other metals.
First Aid MeasuresIngestion: Treat symptomatically. Get medical attention.
Eyes: Flush with water at least 30 minutes. Get medical attention if eye irritation develops or persists.
Skin: Wash with soap and water get medical attention if eye irritation develops or persists.
Inhalation: Remove exposed person to fresh air if adverse effects are observed.
Accidental Release
Spill procedure :PPE must be worn. Ventilate area if spilled in a confined space or poorly ventilated area. Prevent entry into sewers and waterways. Pick up free liquid for recycle and/or disposal. Residual liquid can be absorbed on inert material.
Mandatory PPE
Eye/face protectionSafety Glasses.
Skin protectionUse good industrial hygiene practices to avoid skin contact. If contact with the material may occur wear chemically protective gloves.No special clothing requirement.
Respiratory ProtectionUse respirator with a combination organic vapor and high efficiency filter cartridge if recommended exposure limit is exceeded. Use self-contained breathingapparatus for entry into confined space, for other poorly ventilated areas and for large spill clean-up sites.
Hygiene MeasuresWash thoroughly after handling this product.
Caustic soda (Sodium hydroxide)
Chemical names:Sodium HydroxideMolecular formula:
Physical Properties:Colourless and odourless viscous liquidCorrosive
Hazards:Causes severe skin burns and eye damage. May be corrosive to metals.
Handling and Storage
Used in closed system Use only in well-ventilated areas. Keep away from Incompatible products.
Storage:
Store in original container. Keep in a well-ventilated place. Keep in properly labeled containers. Keep container closed. Keep in a banded area. Keep away from Incompatible products. Regularly check the condition and temperature of the containers. Minimum storage temperature: 25C
First Aid MeasuresIf inhaled:Move to fresh air. Artificial respiration if needed. Victim to lay down in recovery position, keep rest and warm. Call a doctor.
Eye contact:Wash out with water lifting the upper and lower eyelids for 15 minutes. Call a doctor and take victim immediately to hospital.
Skin contact:Take off contaminated clothes immediately. Wash out for 10 minutes. Keep warm and in a quiet place. Wash contaminated clothing before reuse.
If swallowed:Seek medical help. Take victim to hospital. If swallowed rinse mouth with water. Artificial respiration may be necessary.Accidental release measures: Prevent further leakage if safe to do so. Keep away from compatible products.
Environmental precautions:
Dispose of rinse water in accordance with local and national regulations.
Mandatory PPE :Respiratory system: Wear respirator if exposure to mistSkin and body: Wear overall/apron if there is risk of splashing wear PVC. Wear rubber bootsHands: Wear PVC or Rubber glovesEyes: Wear chemical goggles
Storage on site :
Cresol/Xylenol
Chemical names:
Molecular formula:
Chemical properties:Appearance: LiquidColour: AmberOdour:CharacteristicP.H:Melting point: Flash point:
HazardsInhalation : Harmful by inhalation
Ingestion:Toxic if swallowed
Skin contact Causes severe burn, toxic if in contact with skin
Eye Contact : Cause burn, watering ands redness may occur
Handling and storage
Usage precautions: Use in when ventilated area
Storage precautions :Keep in cool dry and well ventilated area. Keep containers tightly closed and keep away from sources of ignition.
First aid measures
Inhalation :Harmful by inhalation. Inhalation may cause nausea and vomiting. Move the exposed person to fresh air. If breathing stops, provide artificial respiration. If breathing is difficult give oxygen. Seek medical attention.
Ingestion: Ingestion causes burns to the respiratory tract. Ingestion may cause damage to CNS. If swallowed, seek medical advice immediately and show this container or label. Drink a glass of water. Do not induce vomiting.
Skin contact:Causes burns. Wash off immediately with plenty of soap and water. Remove contaminated clothing. Apply PEG/EtOH solution liberally to affected area. Allow to remain 15 to 30 seconds, then wash with water. Continue cycle of water - PEG/EtOH solution for at least 15 minutes. (PEG/EtOH solution consists of 2 parts polyethylene glycol 400 to 1 part ethanol. For external use only). Finish decontamination with thorough washing using soap and water. Seek medical attention if irritation or symptoms persist.
Eye contact: Causes burns and may cause serious damage to eyes. Causes severe inflammation and may damage the cornea. Rinse immediately with plenty of water for 15 minutes holding the eyelids open. Contact lenses should be removed. Seek medical attention.
Accidental releasePersonal precautions:Ensure adequate ventilation of the working area. Evacuate personnel to a safe area. Eliminate all sources of ignition. Wear suitable protective equipment.
Environmental precautions:Do not allow product to enter drains. Prevent further spillage if safe.
Spill clean up methods:Absorb with inert, absorbent material. Transfer to suitable, labeled containers for disposal
Mandatory PPEEngineering measures: Ensure adequate ventilation of the working area
Respiratory protection: Wear Suitable respiratory equipment
Hand protection:Butyl rubber gloves
Eye protection:Face shield
Protective equipment : Wear chemical protective clothing
Storage on site - Tank 443
Ethyl Acrylate
Chemical names:
Molecular formula:
Physical properties:
Appearance: LiquidColour: ColourlessOdour:PungentP.H:Melting point: Flash point:
Hazards
Potential health hazards:Skin sensitizer. Inhalation could caused nausea, sore throat, stomach pains and vomiting.
Environmental effect:Toxic to aquatic life, readily biodegradable. Slightly bioaccumulable.
Physical and chemical hazards:Highly flammable. Polymerisation is exothermic and can degenerate into a uncontrolled reaction
Specific hazards: Highly flammable. Harmful if inhaled, ingested, contacted with skin and with eyes.
Handling and storage
Handling: Use in well ventilated areas. Provide eye baths, showers and water facilities near point of use. Do not eat, drink or smoke near area of use. Wash hands after use. Wash down contaminated clothing before removal.
Storage: Keep in well ventilated place and away from sources of ignition. Do not smoke and maintain the container ensuring 5-7% oxygen levels. Keep away from direct sunlight.
First aid measures
General advice: Take off immediately all contaminated clothing. Wash contaminated clothing before reuse.
Inhalation:Move to fresh air. Oxygen or artificial respiration if needed. If persistent problems occur consult doctor.
Skin contact:Wash immediately thoroughly with soap and plenty of water.
Eye contact:Wash well open eyes immediately with water and thoroughly.
Fire fighting measures
Suitable extinguishing media: Water spray, foam, CO2, dry powder
Accidental release measures
Personal precautions:Keep away all sources of ignition. Keep people away from upwind and spill/leakage.
Environmental:Do not let get in drains, dam up with sand or inert earth.
Recovery:Pump into a labelled inert emergency tank. Absorb remainder with inert absorbent material. Rinse with water and recover the waste water for treatment
Elimination:Destroy the product by incineration
Mandatory PPE
Respiratory protection:In case of insufficient ventilation, wear respirator. If high concentration or prolonged use wear a breathing apparatus.
Hand protection:Neoprene gloves
Eye protection: Safety glasses with side shields
Skin and body protection:Protective suit and boots
Storage on site:
HCI (hydrochloric acid)
Chemical properties:
Appearance: liquid
Colour: Light yellowOdour:PungentP.H:Melting point:
Flash point:
Hazards: Causes burns and irritation.
Handling and storage
Handling:Avoid inhalation of vapour or mist
Storage :Must be kept sealed. Keep in cool, dry and well ventilated place.
First aid measures
General advice:consult a physician and show this safety sheet to the doctor
If inhaled: If breathed in move person to fresh air. If not breathing give artificial respiration
In case of skin contact:In case of skin contact take off contaminated clothing and shoes immediately. Wash with soap and plenty of water.
In case of eye contact:Rinse thoroughly with plenty of water for at least 15 minutes..
Accidental release
Personal precautions:Use PPE, avoid breathing vapour. Ensure adequate ventilation.
Environmental precautions:Do not let product enter drain
Methods for cleaning up:Soak up with inert absorbent material and dispose of as hazardous waste.
PPE :With high risk use full face respirator.
Storage on site:
Maleic anhydride
Physical and chemical properties
Appearance: Colour:
Odour:P.H:Melting point: Flash point:
Hazards: Harmful if swallowed. Causes severe skin burns and eye damage. May cause allergy or asthma symptoms or breathing difficulties if inhaled.
Handling and storage
Precautions for safe handling: Provide sufficient air exchange and/or exhaust in work rooms. In case of insufficient ventilation, wear suitable respiratory equipment. Do not breathe vapors.
Requirements for storage:Keep container tightly closed in a dry and well-ventilatedplace. The product is hygroscopic. Protect from moisture.
Further information:Storage in heated containers
First aid measures
General advice : Take off contaminated clothing and shoes immediately.
If inhaled : Move to fresh air
In case of skin contact:Cool melted product on skin with plenty of water. Do not remove solidified product. Wash off immediately with plenty of water.
In case of eye contact : Rinse immediately with plenty of water and seek medicaladvice.
If swallowed : If swallowed, seek medical advice immediately and show this container or label
Accidental release measures Personal precautions :Ensure adequate ventilation
Environmental precautions:Do not allow material to contaminate ground water system. Do not flush into surface water or sanitary sewer system.
Methods for cleaning up:Allow to solidify, use mechanical handling equipment. The material taken up must be disposed of in accordance with regulations.PPE
Respiratory protection: In inadequately ventilated areas, where workplace limits are exceeded, where unpleasant odors exist or where aerosols are in use, or smoke and mist occur, use self-contained breathing apparatus or breathing apparatus with a combined filter
Eye protection:Tightly fitting safety goggles
Storage on site:
DTBP (Di-tert-butylperoxide)
Physical properties chemical nature:Pure liquidAppearance:Liquid Colour:ColourlessMelting point:Boiling point:
HazardsO - OxidizingF - Highly flammableHandling and storage
Handling: Use PPE
Storage:Electrical installations / working materials must comply with the technological safety standards. Containers which are opened must be carefully resealed and kept upright to prevent leakage. Keep container tightly closed. No smoking
Further info on storage:Avoid impurities (e.g. rust, dust, ash), risk of decomposition. Please see our technical data sheet for further information and safety advice.
Advice on common storage: Store apart from other dangerous and incompatible substances
Storage temperature: less than 30 deg C
First aid measures
General advice:Take off all contaminated clothing immediately. Never give anything by mouth to an unconscious person. Remove from exposure, lie down. In the case of accident or if you feel unwell, seek medical advice immediately (show the label where possible)
Inhalation: Remove to fresh air and call a doctor immediatelySkin Contact: Wash off immediately with soap and plenty of water
Eye contact: Rinse with plenty of water and seek medical advice Ingestion : Clean mouth with water and drink afterwards plenty of water.If a person vomits when lying on his back, place him in the recoveryposition. Do NOT induce vomiting. If swallowed, seek medical advice immediately and show this container or label.
Accidental release measures
Personal precautions:Wear respiratory protection. Wear personal protective equipment
Environmental precautions:Avoid subsoil penetration. Do not allow material to contaminate ground water system. Do not contaminate water. If the product contaminates rivers and lakes or drains inform respective authorities. Do not let product enter drains.
Methods for cleaning up: Remove mechanically and with care (e.g. with clean polyethylene plastic shovel). Contain and collect spillage with non-combustible absorbent material, (e.g. sand, earth, diatomaceous earth, vermiculite) and place in container for disposal according to local / national regulations.
Additional advice:Never add other substances or waste material to product residue. Move product residue to a safe place and dispose of properly.
Personal protective equipment
Respiratory protection:Short duration filter unit: Filter A
Hand protection:Skin should be washed after contact. Glove thickness : 0,5 mmBreak through time : >= 8 hMaterial : butyl-rubber
Eye protection:Tightly fitting safety goggles. Face protection
Skin and body protection:Protective suit. Remove and wash contaminated clothing before re-use.
Hygiene measures:Wash hands before breaks and immediately after handling the product. Keep away from food, drink and animal feedingstuffs.
Storage on site:
Propylene (C3H6)
Physical properties
Physical state : Gas (Liquefied Gas)Colour:ColourlessOdour:CharacteristicMelting point:Initial boiling point:Flash point:
Hazards Extremely flammableKeep away from heat, sparks, open flames and hot surfaces. - No smoking.Eliminate all ignition sources if safe to do so.
Handling and storage
Handling :Put on appropriate personal protective equipment (see Section 8). Contains gas under pressure. Do not get in eyes or on skin or clothing. Avoid breathing gas. Us only with adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Do not enter storage areas and confined spaces unless adequately ventilated. Store and use away from heat, sparks, open flame or any other ignition source. Use explosion-proof electrical (ventilating, lighting and material handling) equipment. Use only non-sparking tools. Empty containers retain product residue and can be hazardous. Do not puncture or incinerate container.
Storage :Store in accordance with local regulations. Store in a segregated and approved area. Store away from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see section 10). Eliminate all ignition sources. Keep container tightly closed and sealed until ready for use.
First aid measures
Inhalation: Remove victim to fresh air and keep at rest in a position comfortable for breathing. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Get medical attention if adverse health effects persist or are severe. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband.
Skin contact:Extremely cold material. Can cause burns similar to frostbite. Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Get medical attention if symptoms occur. Wash clothing before reuse. Clean shoes thoroughly before reuse.
Eye contact: Extremely cold material. Can cause burns similar to frostbite. Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10 minutes. Get medical attention if irritation occurs.
Ingestion: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Get medical attention if adverse health effects persist or are severe. Ingestion of liquid can cause burns similar to frostbite. If frostbite occurs, get medical attention. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. As this product rapidly becomes a gas when released, refer to the inhalation section.
Accidental releaseDecomposition products may include the following materials:
carbon dioxidecarbon monoxide
Personal protective equipment
Respiratory protection - Use a properly fitted, air-purifying or air-fed respirator complying with an approved standard if a risk assessment indicates this is necessary. Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe working limits of the selected respirator. Recommended: self-contained breathing apparatus (SCBA)
.
Skin and body Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. If contact with the liquid is possible, insulated gloves suitable for low temperatures should be worn. 4-8 hours (breakthrough time): Insulated gloves suitable for low temperatures ; neoprene , nitrile rubber
Vinyl acetate
Chemical propertiesform - Liquid
Colour - ColourlessOdour - SweetFlash point -Melting point -Boiling point -
HazardsHighly flammable
Handling
Advice on safe handling:Provide sufficient air ventilation.
Storage
Storage conditions:keep in dry cool and well ventilated area. Open container with care
Incompatible products:oxidising agents, radical initiators, strong acids, amides
First aid measures
General information:Remove contaminated clothing immediately and dispose of safely
Inhalation:Keep at rest. Move to fresh air.
Skin: Wash off immediately with soap and plenty of water, removing all contaminated clothes and shoes
Eyes:Immediately rinse with plenty of water for 15 minutes while moving the eyelids.
Ingestion: Rinse with plenty of water. Drink plenty of water (if conscious)
Accidental release measures
Personal precautions:Prevent contact with skin and eyes. Keep away from all sources of ignition
Environmental precautions:Prevent further leakage spillage. Dispose of properly
Methods for cleaning up:soak up with inert absorbent material
Personal protection equipment
Respiratory protection:Respirator with A/PA filter
Eye protection:Tightly fitting safety goggles and with the chance of splashing wear a face mask
Skin protection:Impervious clothing
Hand protection:Chemical resistant glovesStorage:
Phenol (C6H5OH)
Chemical properties
Appearance: White solid or colourless liquidPhysical state : Liquid>41deg C, Solid 65 o C.
Hand protection:Polyvinyl alcohol or nitrile-butyl rubber gloves
Eye protection:Tightly fitting safety goggles
Skin and body protection:Chemical resistive apron
Hygiene measures:Handle in accordance with good industrial hygiene and safety practice.Wash hands before breaks and immediately after handling the productDo not smoke, eat or drink while handling this material.
Storage on site:
Calcium hydroxide
Chemical properties
Appearance: SolidColour:Colorless/whiteOdour:OdorlessP.H.:Temperature :Dangers:Solubility:Stability:
Handling and storage
Usage precautions:Avoid spilling, skin and eye contact. Ventilate well, avoid breathing vapors. Use approved respirator if air contamination is above accepted level. Wear full protective clothing for prolonged exposure and/or high concentrations.
Storage precautions:Keep cool, dry and well ventilated area
Storage criteria:Chemical storage
First aid measures
General: Seek medical attention for all burns regardless of how minor they may be Inhalation:move exposed person to fresh air and keep warm and at rest Ingestion:never make an unconscious person vomit or drink a lot of water
Skin:remove affected person from source of contamination. Immediately flush contaminated skin with water.
Eyes:wash eyes with plenty of water while lifting the eye lid area.
Accidental release
Spillage clean up methods:Shovel into dry containers. Cover and move the containers. Flush the area with water. Collect for reclamation or absorb in vermiculite, dry sand or similar material. Absorb in vermiculite, dry sand or earth and place into containers. Gather in poly lined drum. Neutralize small amounts with diluted hydrochloric acid (HCl) and flush to sewer with large amounts of water
Exposure control and PPE
Ventilation: provide adequate local exhaust ventilation.Protective gloves:use protective rubber gloves
Eye protection:wear chemical safety goggles
Other protection:provide eyewash station and safety shower.Hygiene measures:eating drinking smoking is prohibited
Storage on site
Carbon
Chemical product name
Chemical properties
Physical state:Solid PowderColour:BlackSolubility:P.H:Flash point:Stability:Hazardous products:Hazards:
Handling and storage
Handling:
Storage:.
First aid measures
Inhalation:
Ingestion:
Eye contact:
Accidental release measures
Personal precautions:
Environmental precautions:
Exposure controls/PPE
Engineering measures:
PPE:
Skin and body:
Hands:
Eyes:
Hygiene measures:
Storage on site:
Magnesium Chloride
Product name
Chemical properties
Appearance:
Colour:Boiling point:Melt/freezing:Metals to avoid:Hazards:
Hazards
Hazard decomposition products:
Ingestion:
Skin:
Eyes:
Route of entry:.Key point:
Handling and storage
Usage precautions:
Storage precautions:
Accidental release measures
Personal precaution in spill:`
Spill clean up methods:
First aid measures
Inhalation:
Ingestion:
Skin:
Eyes:
Fire fighting measures
Extinguishing media:
Hazardous combustion products:
Protective measures in fire:
PPE
Ventilation:
Respirators:
Protective gloves:
Eye protection:
Other protection:
Hygiene measures:
Storage on site:
Phosphorus Oxychloride
Use of substance
Chemical properties
Physical state -Colour -
Odour - P.H. - Boiling point - Melting point - Toxic, corrosive
Hazards
Physical and chemical:
Human and health:
Over exposure:
Ingestion:
Skin:
Eyes -
Handling and storage
Handling:
Storage:
First aid measures
Inhalation:
Ingestion:
Skin contact:
Accidental release
Personal precautions:
Environmental precautions:
Large spill:
Small spill:
Personal protective equipment
Hand protection:
Eye protection:
Skin protection:
Environmental exposure:
Storage on site:
Sodium hypophosphite (NaH2PO2,H2O)
Physical and chemical properties
Name:Form:Colour:Odour:Decomposition temp:Flash point:P.H.Hazards:Product use:
Hazards
Potential health effects:
Handling
Storage
General:
First aid measures
If in eyes: If on skin:
If inhaled:
If swallowed:
Accidental release
Personal precautions: Environmental precautions:
Methods for cleaning up:
Personal Protection Equipment
Eye protection:
Hand protection:
Body protection:
Respiratory protection:
Ventilation:
Storage on site:
Sodium persulphate (Na2S208)
Physical and chemical properties
Physical form:Colour:
Odour:Hazards: Stability:
Hazards
Physical and chemical:
Health:
Safety:
Materials to avoid:
Hazardous reactions:Handling and storage
Advice on safe handling:
Storage conditions:
First aid measures
Inhalation:
Skin contact:.
Eye contact:
Ingestion:
Accidental release
Methods for cleaning up:.
Personal protection equipment
Personal protection:
Eye protection:
Skin protection:
Respiratory protection:
Other protection:.
Storage on site:
Reofos finished products
Reofos 1882:Reofos 95:Application:Application:
Reofos 249:Reofos BAPP:Application:Application:
Reofos 293:Reofos 65:Application:Application:
Reofos 35:Application:
Reofos 50:Application:
Reofos 508:Application:
Hazard
Handling and storage
Usage precautions:
Storage precautions:
First aid measures
Inhalation:
Ingestion:
Skin contact:
Eye contact:
Accidental release measures
Personal precautions:
Spill clean up methods:
Fire fighting measures
Extinguishing media:
Unusual fire and explosion :
Protective measures:
Personal protective equipment
Eye protection:
Hand protection:
Skin and body protection:
Respiratory:
Hygiene measures:
Storage on site:
Water Additives finished products
Belclene 400:Chemical name: Application:
Belclene 500:Chemical name:Application:
Belclene 283:283QChemical name:Application:
Belclene 200:Chemical name:Application:
Belclene 200LA:Chemical name:Application:
Hazards
Stability:
Conditions to avoid:
Materials to avoid:
Hazardous decomposition products:
Inhalation:Ingestion:Skin contact:.Eye contact:
First aid measures
Inhalation:
Ingestion:
Skin:
Eyes:
Handling and storage
Usage precautions:
Storage precautions:
Accidental release measures
Personal precautions:
Environmental precautions:
Spill clean up methods:
Personal protection
Process conditions:
Engineering measures:
Respiratory equipment:
Hand protection:
Eye protection:
Other protection:
Hygiene measures:
Skin protection:
Storage on site:Bellasol S30:Chemical name: Application:
Bellasol S31:Chemical name:Application:
Hazards
Handling and storage
Usage precautions:
Storage precautions:
Accidental release
Personal precautions:
Environmental precautions:
Spill clean up methods:
First aid measures:
Inhalation:
Ingestion:
Skin:
Eyes:
Personal protection
Engineering measures:
Respiratory equipment:
Hand protection:
Eye protection:
Skin protection:
Storage on site:
Belsperse 161:Chemical name:Application:
Belsperse 164:Chemical name:Application:
Hazards
Handling and storage
Handling:
Storage:
First aid measures
Eyes:
Skin:
Ingestion:
Inhalation:
Accidental release measures
Personal protection
Engineering controls:
Eyes and face:
Respiratory:
Protective clothing:
Storage on site:
Flocon 135:Chemical name:Application:
Hazard identification
Handling and storage
Usage precautions:
Storage precautions:
First aid measures
Inhalation:
Ingestion:
Skin contact:
Eye contact:
Accidental release
Environmental release:
Spill clean up methods:
Personal protection
Engineering measures:
Respiratory equipment:
Hand protection:
Eyes and face:
Other protection:
Hygiene measures:
Skin protection:
Storage on site:
T421
T424
T422
T425
T423
T426
T427
T428
T429
T431
T432
T433
T436
T438
T413
T412
T419
T414
T417
T418
T416
T415
T421 T428 T422 T429 T423 T431 T424 T432 T425 T433 T426 T419 T418T417 T416T415 T414 T413 T412 T436 T438
TANK FARM 4FRONT
T441
T450
T447
T445
T443
DTBP unloading station
T440
T442
T444
R446
R448
R451
T410
T404
T402
T406
T408
T449
P410A
P443B
P464
P466
P410B
P406
P404
P402A
P402B
P460
P459
P458
P448
P446
P450A
P451
P450B
P447
P443A
P440
T45
T46
T48
T47
T164
T49
T50
T145
T137
T122
T102
T101
T146
T37
T38
T40
T144
T143
T142
T103
T104
T123
T124
T125
T5
T1
T3
T7
T2
T39
T8
T6
T4
T1 T2 T3 T4 T5 T6 T7 T8T37, 38, 39 & 40T45 T46 T47 T48 T49 T50 T64 T101 T102 T103 T104 T122 T123 T124T125 T137 T142 T143 T144 T145 T146
Tank farm 6
Tank farm 7
T129
T131
T159
T155
T031
T028
T030
T029
V165
T119
V166
T120
T121
T019
T020
T021
T022
T023
T041
24
T112 T019 T041 T106 T020 T159T105 T021T155V165T022 T131V166 T023 T129T119T132 T025T120 T149 T026T121T156 T027 T028 T029 T030 T031
TANK FARM 5
T027
T026
T132
T149
T156
T025
T112
T106
T105
T098
T074C
T074B
T074A
T087
T099
T074A T009 T074B T097 T074C T089 T098T087 T099
TANK FARM 8
T089
T097
T009