certificate - everlight europe › img › cms › safety_certs › nemkop112… · nemko as...

CERTIFICATENo. P11214765/A5

Order No. 257066 /63

Date of issue 29-09-2014

Eunhye SongCertification Department

Nemko ASGaustadalléen 30, P.O. Box 73 Blindern, 0314 Oslo, NorwayTEL +47 22 96 03 30 FAX +47 22 96 05 50 EMAIL [email protected] NUMBER NO974404532 nemko.com

Product Optocoupler

Applicant Everlight Electronics Co., Ltd.No.6-8, Zhonghua Rd., Shulin Dist., New Taipei City23860New Taipei CityTaipei 23860Taiwan

Manufacturer Everlight Electronics Co., Ltd.No.6-8, Zhonghua Rd., Shulin Dist., New Taipei City23860New Taipei CityTaipei 23860Taiwan

Factory Everlight Electronic (China) Co., Ltd.No. 2135 Zhong Shan North Rd. Wujiang EconomyDevelopment Zone (Yun Xi Area), Songling Town,Wujiang City, Jiang SuChina

See next page(s)

Ratings 250Vrms

Trade mark EVERLIGHT

Model / Type Ref. EL817.

Principal characteristics Minimum external creepage distance is measured to 7.7mm, minimum internalcreepage distance is measured to 6.0mm and minimum distance throughinsulation is measured to 0.5mm. Tested for reinforced insulation. Thermalcycling test, 10 cycles. Each cycle: 68h in 110 degree C, 1h in 25 degree C, 2hin 0 degree C and 1h in 25 degree C. After the cycling test a humidity test for48h in 93% relative humidity. Electric strength test between input and output4800Vac/1 minute. The symbol "." in type designation may be blank, A~Z ornumbers, and denote different pin shape. Maximum operating temperature: 110degrees C.

See next page(s)

A sample of the product was testedand found to be in conformity with

TRON EN 60065:2002;A1;A11;A2;A12IEC 60065(ed.7);am1;am2

OFF EN 60950-1:2006;A11;A1;A12;A2IEC 60950-1(ed.2);am1;am2

LITE EN 61347-1:2008;A1IEC 61347-1(ed.2);am1

HOUS EN 60335-1:2012IEC 60335-1(ed.5)


Order No. 257066 /63




Replaces This certificate replaces the certificate dated 07-04-2014 due to misprinting of Model name.

Validity This certificate documents conformity with the standards shown, and also applies as license foruse of Nemkos name and certification mark. The certificate and license is valid as long as theapplicable conditions are complied with, and provided that any changes to the product are notifiedto Nemko for acceptance prior to implementation.New standards or amendments to the standards may imply that the product design must beupdated and/or that re-testing and re-certification is necessary.

Additional information See next page(s)

Additional model(s) See next page(s)


Order No. 257066 /63




Product Optocoupler

Pos. No 1Model / Type Ref. EL2801.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler (SMD type). Minimum external creepage distance is measured

to 5.0mm, minimum internal creepage distance is measured to 4.0mm andminimum distance through insulation is measured to 0.4mm. Tested forreinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in110 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C.After the cycling test a humidity test for 48h in 93% relative humidity. Electricstrength test between input and output 4800Vac/1 minute. The symbol “.” intype designation may be blank, A~Z or numbers, and denote different pinshape. Maximum operating temperature: 110 degrees C.

Product Optocoupler

Pos. No 2Model / Type Ref. MCT210.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,

minimum internal creepage distance is measured to 6.0mm and minimumdistance through insulation is measured to 0.5mm. Tested for reinforcedinsulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degree C,1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After the cyclingtest a humidity test for 48h in 93% relative humidity. Electric strength testbetween input and output 4800Vac/1 minute. The symbol “X” in type denotesX = Part no. (1,2,3).The symbol “.” in type designation may be blank, A~Z ornumbers, and denote different pin shape. Maximum operating temperature:110°C


Order No. 257066 /63




Product Optocoupler

Pos. No 3Model / Type Ref. CNY17-X.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,

minimum internal creepage distance is measured to 6.0mm and minimumdistance through insulation is measured to 0.5mm. Tested for reinforcedinsulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degreeC, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After thecycling test a humidity test for 48h in 93% relative humidity. Electric strengthtest between input and output 4800Vac/1 minute. The symbol “X” in typedenotes X = Part no. (1,2,3,4,5).The symbol “.” in type designation may beblank, A~Z or numbers, and denote different pin shape. Maximum operatingtemperature: 110°C

Product Optocoupler

Pos. No 4Model / Type Ref. MOC811X.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,

minimum internal creepage distance is measured to 6.0mm and minimumdistance through insulation is measured to 0.5mm. Tested for reinforcedinsulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degreeC, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After thecycling test a humidity test for 48h in 93% relative humidity. Electric strengthtest between input and output 4800Vac/1 minute. The symbol “.” in typedesignation may be blank, A~Z or numbers, and denote different pin shape.Maximum operatingtemperature: 110 degrees C.


Order No. 257066 /63




Product Optocoupler

Pos. No 5Model / Type Ref. H11AX.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,


Product Optocoupler

Pos. No 6Model / Type Ref. TIL111.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,


Product Optocoupler

Pos. No 7Model / Type Ref. TIL117.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,



Order No. 257066 /63




Product Optocoupler

Pos. No 8Model / Type Ref. EL302X.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics RANDOM PHASE PHOTOTRIAC Minimum external creepage distance is

measured to 7.7mm, minimum internal creepage distance is measured to5.5mm and minimum distance through insulation is measured to 0.5mm.Tested for reinforced insulation. Thermal cycling test, 10 cycles. Eachcycle: 68h in 100 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in25 degree C. After the cycling test a humidity test for 48h in 93% relativehumidity. Electric strength test between input and output 4800Vac/1 minute.The symbol “X” in type denotes X = Part no. (0,1,2,3,4).The symbol “.” intype designation may be blank, A~Z or numbers, and denote different pinshape. Maximum operating temperature: 100°C

Product Optocoupler

Pos. No 9Model / Type Ref. EL305X.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics ZERO-CROSSING PHOTOTRIAC Minimum external creepage distance

is measured to 7.7mm, minimum internal creepage distance is measuredto 5.5mm and minimum distance through insulation is measured to 0.5mm.Tested for reinforced insulation. Thermal cycling test, 10 cycles. Eachcycle: 68h in 100 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in25 degree C. After the cycling test a humidity test for 48h in 93% relativehumidity. Electric strength test between input and output 4800Vac/1 minute.The symbol “X” in type denotes X = Part no. (0,1,2,3,4).The symbol “.” intype designation may be blank, A~Z or numbers, and denote different pinshape. Maximum operating temperature: 100°C


Order No. 257066 /63




Product Optocoupler

Pos. No 10Model / Type Ref. EL307X.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics ZERO-CROSSING PHOTOTRIAC Minimum external creepage distance is


Product Optocoupler

Pos. No 11Model / Type Ref. EL2730.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics DUAL CHANNEL SPLIT DARLINGTON Minimum external creepage

distance is measured to 8.0mm, minimum internal creepage distance ismeasured to 5.0mm and minimum distance through insulation is measuredto 0.5mm.Tested for reinforced insulation. Thermal cycling test, 10 cycles.Each cycle: 68h in 100 degree C, 1h in 25 degree C, 2h in 0 degree C and1h in 25 degree C. After the cycling test a humidity test for 48h in 93%relative humidity. Electric strength test between input and output 4800Vac/1minute. The symbol “.” in type designation may be blank, A~Z or numbers,and denote different pin shape. Maximum operating temperature: 100degrees C.


Order No. 257066 /63




Product Optocoupler

Pos. No 12Model / Type Ref. EL3H4.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics PHOTODARLINGTON Minimum external creepage distance is measured

to 7.7mm, minimum internal creepage distance is measured to 5.5mm andminimum distance through insulation is measured to 0.5mm. Tested forreinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in100 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C.After the cycling test a humidity test for 48h in 93% relative humidity. Electricstrength test between input and output 4800Vac/1 minute.The symbol “.” intype designation may be blank, A~Z or numbers, and denote different pinshape. Maximum operating temperature: 100 degrees C.

Product Optocoupler

Pos. No 13Model / Type Ref. EL2731.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics DUAL CHANNEL SPLIT DARLINGTON Minimum external creepage



Order No. 257066 /63




Product Optocoupler

Pos. No 14Model / Type Ref. EL2601.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics SINGLE CHANNEL HIGH SPEED LOGIC GATE Minimum external

creepage distance is measured to 8.0mm, minimum internal creepagedistance is measured to 5.0mm and minimum distance through insulationis measured to 0.5mm.Tested for reinforced insulation. Thermal cyclingtest, 10 cycles. Each cycle: 68h in 100 degree C, 1h in 25 degree C, 2h in0 degree C and 1h in 25 degree C. After the cycling test a humidity test for48h in 93% relative humidity. Electric strength test between input and output4800Vac/1 minute. The symbol “.” in type designation may be blank, A~Z ornumbers, and denote different pin shape. Maximum operating temperature:100 degrees C.

Product Optocoupler

Pos. No 15Model / Type Ref. EL260L.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics SINGLE CHANNEL HIGH SPEED LOGIC GATE Minimum external



Order No. 257066 /63




Product Optocoupler

Pos. No 16Model / Type Ref. CNX35U.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,

minimum internal creepage distance is measured to 6.0mm and minimumdistance through insulation is measured to 0.5mm. Tested for reinforcedinsulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degreeC, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After thecycling test a humidity test for 48h in 93% relative humidity. Electric strengthtest between input and output 4800Vac/1 minute. The symbol “.” in typedesignation may be blank, A~Z or numbers, and denote different pin shape.Maximum operating temperature: 110 degrees C.

Product Optocoupler



Product Optocoupler




Order No. 257066 /63




Product Optocoupler



Product Optocoupler

Pos. No 20Model / Type Ref. SL5500.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,


Product Optocoupler




Order No. 257066 /63




Product Optocoupler



Product Optocoupler

Pos. No 23Model / Type Ref. 6N138.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics SINGLE CHANNEL HIGH SPEED TRANSISTOR. Minimum external



Order No. 257066 /63




Product Optocoupler


measured to 7.7mm, minimum internal creepage distance is measured to5.5mm and minimum distance through insulation is measured to 0.5mm.Tested for reinforced insulation. Thermal cycling test, 10 cycles. Eachcycle: 68h in 100 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in25 degree C. After the cycling test a humidity test for 48h in 93% relativehumidity. Electric strength test between input and output 4800Vac/1 minute.The symbol “X” in type denotes X = Part no. (1,2,3).The symbol “.” in typedesignation may be blank, A~Z or numbers, and denote different pin shape.Maximum operating temperature: 100°C

Product Optocoupler

Pos. No 25Model / Type Ref. EL2611.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics SINGLE CHANNEL HIGH SPEED LOGIC GATE Minimum external



Order No. 257066 /63




Product Optocoupler

Pos. No 26Model / Type Ref. EL261A.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics SINGLE CHANNEL HIGH SPEED LOGIC GATE Minimum external


Product Optocoupler


minimum internal creepage distance is measured to 6.0mm and minimumdistance through insulation is measured to 0.5mm. Tested for reinforcedinsulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degree C,1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After the cyclingtest a humidity test for 48h in 93% relative humidity. Electric strength testbetween input and output 4800Vac/1 minute. The symbol “X” in type denotesX = Part no. (0,1,2,3,4,5,6,7,8).The symbol “.” in type designation may beblank, A~Z or numbers, and denote different pin shape. Maximum operatingtemperature: 110°C


Order No. 257066 /63




Product Optocoupler



Product Optocoupler

Pos. No 29Model / Type Ref. EL316X.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics SCHMITT TRIGGER Minimum external creepage distance is measured to

7.7mm, minimum internal creepage distance is measured to 5.5mm andminimum distance through insulation is measured to 0.5mm. Tested forreinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in100 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C.After the cycling test a humidity test for 48h in 93% relative humidity. Electricstrength test between input and output 4800Vac/1 minute. The symbol “X” intype denotes X = Part no. (1,2,3).The symbol “.” in type designation may beblank, A~Z or numbers, and denote different pin shape. Maximum operatingtemperature: 100°C


Order No. 257066 /63




Product Optocoupler


measured to 7.7mm, minimum internal creepage distance is measured to5.5mm and minimum distance through insulation is measured to 0.5mm.Tested for reinforced insulation. Thermal cycling test, 10 cycles. Eachcycle: 68h in 100 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in25 degree C. After the cycling test a humidity test for 48h in 93% relativehumidity. Electric strength test between input and output 4800Vac/1 minute.The symbol “X” in type denotes X = Part no. (0,1,2,3,4).The symbol “.” intype designation may be blank, A~Z or numbers, and denote different pinshape. Maximum operating temperature: 100 degrees C.

Product Optocoupler

Pos. No 31Model / Type Ref. H11LX.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics SCHMITT TRIGGER Minimum external creepage distance is measured to

7.7mm, minimum internal creepage distance is measured to 5.5mm andminimum distance through insulation is measured to 0.5mm. Tested forreinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in100 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C.After the cycling test a humidity test for 48h in 93% relative humidity. Electricstrength test between input and output 4800Vac/1 minute. The symbol “X” intype denotes X = Part no. (1,2,3).The symbol “.” in type designation may beblank, A~Z or numbers, and denote different pin shape. Maximum operatingtemperature: 100 degrees C.


Order No. 257066 /63




Product Optocoupler

Pos. No 32Model / Type Ref. EL20X.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Dual channel Optocoupler Minimum external creepage distance is measured

to 4.4mm, minimum internal creepage distance is measured to 3.5mm andminimum distance through insulation is measured to 0.4mm. Tested forbasic and supplementary insulation. Thermal cycling test, 10 cycles. Eachcycle: 68h in 110 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in25 degree C. After the cycling test a humidity test for 48h in 93% relativehumidity. Electric strength test between input and output 2400Vac/1 minute.The symbol “.” in type designation may be blank, A~Z or numbers, anddenote different pin shape. Maximum operating temperature:110 degrees C.

Product Optocoupler

Pos. No 33Model / Type Ref. EL21X.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Dual channel Optocoupler Minimum external creepage distance is measured



Order No. 257066 /63




Product Optocoupler

Pos. No 34Model / Type Ref. 6N139.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics SINGLE CHANNEL HIGH SPEED TRANSISTOR. Minimum external


Product Optocoupler




Order No. 257066 /63




Product Optocoupler

Pos. No 36Model / Type Ref. MOC810X.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,

minimum internal creepage distance is measured to 6.0mm and minimumdistance through insulation is measured to 0.5mm. Tested for reinforcedinsulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degreeC, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After thecycling test a humidity test for 48h in 93% relative humidity. Electric strengthtest between input and output 4800Vac/1 minute. The symbol “X” in typedenotes X = Part no. (1,2,3,4).The symbol “.” in type designation may beblank, A~Z or numbers, and denote different pin shape. Maximum operatingtemperature: 110°C

Product Optocoupler




Order No. 257066 /63




Product Optocoupler

Pos. No 38Model / Type Ref. CNY17F-X.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler (SMD type). Minimum external creepage distance is measured


Product Optocoupler

Pos. No 39Model / Type Ref. EL357N.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler (SMD type). Minimum external creepage distance is measured


Product Optocoupler




Order No. 257066 /63




Product Optocoupler



Product Optocoupler



Product Optocoupler

Pos. No 43Model / Type Ref. ELD207.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Dual channel Optocoupler Minimum external creepage distance is measured



Order No. 257066 /63




Product Optocoupler

Pos. No 44Model / Type Ref. ELD208.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Dual channel Optocoupler Minimum external creepage distance is measured


Product Optocoupler

Pos. No 45Model / Type Ref. EL2502.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics SINGLE CHANNEL HIGH SPEED TRANSISTOR. Minimum external



Order No. 257066 /63




Product Optocoupler

Pos. No 46Model / Type Ref. ELD213.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics AC INPUT PHOTOTRANSISTOR. Minimum external creepage distance is

measured to 7.7mm, minimum internal creepage distance is measured to6.0mm and minimum distance through insulation is measured to 0.5mm.Tested for reinforced insulation. Thermal cycling test, 10 cycles. Eachcycle: 68h in 110 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in25 degree C. After the cycling test a humidity test for 48h in 93% relativehumidity. Electric strength test between input and output 4800Vac/1 minute.The symbol “X” in type denotes X = Part no. (1,2,3,4).The symbol “.” in typedesignation may be blank, A~Z or numbers, and denote different pin shape.Maximum operating temperature: 110°C

Product Optocoupler

Pos. No 47Model / Type Ref. ELD217.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics SINGLE CHANNEL HIGH SPEED TRANSISTOR. Minimum external



Order No. 257066 /63




Product Optocoupler

Pos. No 48Model / Type Ref. H11AAX.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics SINGLE CHANNEL HIGH SPEED TRANSISTOR. Minimum external


Product Optocoupler

Pos. No 49Model / Type Ref. 6N135.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics SINGLE CHANNEL HIGH SPEED LOGIC GATE. Minimum external

creepage distance is measured to 8.0mm, minimum internal creepagedistance is measured to 5.0mm and minimum distance through insulationis measured to 0.5mm.Tested for reinforced insulation. Thermal cyclingtest,10 cycles. Each cycle: 68h in 100 degree C, 1h in 25 degree C, 2h in0 degree C and 1h in 25 degree C. After the cycling test a humidity test for48h in 93% relative humidity. Electric strength test between input and output4800Vac/1 minute. The symbol “.” in type designation may be blank, A~Z ornumbers, and denote different pin shape. Maximum operating temperature:100 degrees C.


Order No. 257066 /63




Product Optocoupler

Pos. No 50Model / Type Ref. 6N136.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics SINGLE CHANNEL SPLIT DARLINGTON. Minimum external creepage


Product Optocoupler

Pos. No 51Model / Type Ref. 6N137.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics SINGLE CHANNEL SPLIT DARLINGTON. Minimum external creepage



Order No. 257066 /63




Product Optocoupler

Pos. No 52Model / Type Ref. EL250L.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics SINGLE CHANNEL HIGH SPEED TRANSISTOR (Non-Base Bonded)

Minimum external creepage distance is measured to 8.0mm, minimuminternal creepage distance is measured to 5.0mm and minimum distancethrough insulation is measured to 0.5mm.Tested for reinforced insulation.Thermal cycling test, 10 cycles. Each cycle: 68h in 100 degree C, 1h in 25degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test ahumidity test for 48h in 93% relative humidity. Electric strength test betweeninput and output 4800Vac/1 minute. The symbol “.” in type designationmay be blank, A~Z or numbers, and denote different pin shape. Maximumoperating temperature: 100 degrees C

Product Optocoupler

Pos. No 53Model / Type Ref. EL2503.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics SINGLE CHANNEL HIGH SPEED TRANSISTOR (Non-Base Bonded)

Minimum external creepage distance is measured to 8.0mm, minimuminternal creepage distance is measured to 5.0mm and minimum distancethrough insulation is measured to 0.5mm.Tested for reinforced insulation.Thermal cycling test, 10 cycles. Each cycle: 68h in 100 degree C, 1h in 25degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test ahumidity test for 48h in 93% relative humidity. Electric strength test betweeninput and output 4800Vac/1 minute. The symbol “.” in type designationmay be blank, A~Z or numbers, and denote different pin shape. Maximumoperating temperature: 100 degrees C


Order No. 257066 /63




Product Optocoupler

Pos. No 54Model / Type Ref. EL4502.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics DUAL CHANNEL HIGH SPEED TRANSISTOR Minimum external creepage


Product Optocoupler




Order No. 257066 /63




Product Optocoupler

Pos. No 56Model / Type Ref. EL263A.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics DUAL CHANNEL HIGH SPEED LOGIC GATE Minimum external creepage


Product Optocoupler

Pos. No 57Model / Type Ref. EL261N.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics SINGLE CHANNEL HIGH SPEED LOGIC GATE Minimum external



Order No. 257066 /63




Product Optocoupler

Pos. No 58Model / Type Ref. EL263N.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics DUAL CHANNEL HIGH SPEED LOGIC GATE Minimum external creepage


Product Optocoupler

Pos. No 59Model / Type Ref. EL2631.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics DUAL CHANNEL HIGH SPEED LOGIC GATE Minimum external creepage



Order No. 257066 /63




Product Optocoupler

Pos. No 60Model / Type Ref. EL280.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics PHOTODARLINGTON Minimum external creepage distance is measured


Product Optocoupler

Pos. No 61Model / Type Ref. 4N29.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics PHOTODARLINGTON Minimum external creepage distance is measured


Product Optocoupler




Order No. 257066 /63




Product Optocoupler



Product Optocoupler

Pos. No 64Model / Type Ref. H11DX.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics HIGH VOLTAGE PHOTOTRANSISTOR. Minimum external creepage

distance is measured to 7.7mm, minimum internal creepage distance ismeasured to 5.5mm and minimum distance through insulation is measuredto 0.5mm.Tested for reinforced insulation. X = Part no. (1, 2, 3 or 4). Thermalcycling test, 10 cycles. Each cycle: 68h in 100 degree C, 1h in 25 degreeC, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humiditytest for 48h in 93% relative humidity. Electric strength test between inputand output 4800Vac/1 minute. The symbol “.” in type designation may beblank, A~Z or numbers, and denote different pin shape. Maximum operatingtemperature: 100 degrees C.


Order No. 257066 /63




Product Optocoupler

Pos. No 65Model / Type Ref. H11GX.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics HIGH VOLTAGE PHOTODARLINGTON. Minimum external creepage

distance is measured to 7.7mm, minimum internal creepage distance ismeasured to 5.5mm and minimum distance through insulation is measuredto 0.5mm. Tested for reinforced insulation. X = Part no. (1, 2 or 3 ). Thermalcycling test, 10 cycles. Each cycle: 68h in 100 degree C, 1h in 25 degreeC, 2h in 0 degree C and 1h in 25 degree C. After the cycling test a humiditytest for 48h in 93% relative humidity. Electric strength test between inputand output 4800Vac/1 minute. The symbol “.” in type designation may beblank, A~Z or numbers, and denote different pin shape. Maximum operatingtemperature: 100 degrees C.

Product Optocoupler

Pos. No 66Model / Type Ref. EL371.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics HIGH VOLTAGE PHOTODARLINGTON. Minimum external creepage

distance is measured to 7.7mm, minimum internal creepage distance ismeasured to 5.5mm and minimum distance through insulation is measuredto 0.5mm. Tested for reinforced insulation. Thermal cycling test, 10 cycles.Each cycle: 68h in 100 degree C, 1h in 25 degree C, 2h in 0 degree C and1h in 25 degree C. After the cycling test a humidity test for 48h in 93%relative humidity. Electric strength test between input and output 4800Vac/1minute. The symbol “.” in type designation may be blank, A~Z or numbers,and denote different pin shape. Maximum operating temperature: 100degrees C.


Order No. 257066 /63




Product Optocoupler

Pos. No 67Model / Type Ref. EL725.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics HIGH VOLTAGE PHOTODARLINGTON. Minimum external creepage

distance is measured to 7.7mm, minimum internal creepage distance ismeasured to 5.5mm and minimum distance through insulation is measuredto 0.5mm. Tested for reinforced insulation. Thermal cycling test, 10 cycles.Each cycle: 68h in 100 degree C, 1h in 25 degree C, 2h in 0 degree C and1h in 25 degree C. After the cycling test a humidity test for 48h in 93%relative humidity. Electric strength test between input and output 4800Vac/1minute. The symbol “.” in type designation may be blank, A~Z or numbers,and denote different pin shape. Maximum operating temperature: 100degrees C

Product Optocoupler




Order No. 257066 /63




Product Optocoupler



Product Optocoupler




Order No. 257066 /63




Product Optocoupler

Pos. No 71Model / Type Ref. EL816.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.9mm,

minimum internal creepage distance is measured to 6.0mm and minimumdistance through insulation is measured to 0.5mm. Tested for reinforcedinsulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degreeC, 1h in 25degree C, 2h in 0 degree C and 1h in 25 degree C. After thecycling test a humidity test for 48h in 93% relative humidity. Electric strengthtest between input and output 4800Vac/1 minute. The symbol “.” in typedesignation may be blank, A~Z or numbers, and denote different pin shape.Maximum operating temperature: 110 degrees C. Tested for 5000m

Product Optocoupler


minimum internal creepage distance is measured to 6.0mm and minimumdistance through insulation is measured to 0.5mm. Tested for reinforcedinsulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degreeC, 1h in 25degree C, 2h in 0 degree C and 1h in 25 degree C. After thecycling test a humidity test for 48h in 93% relative humidity. Electric strengthtest between input and output 4800Vac/1 minute. The symbol “.” in typedesignation may be blank, A~Z or numbers, and denote different pin shape.Maximum operating temperature: 110°C

Product Optocoupler




Order No. 257066 /63




Product Optocoupler



Product Optocoupler

Pos. No 75Model / Type Ref. HS817.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,


Product Optocoupler

Pos. No 76Model / Type Ref. K817P.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,



Order No. 257066 /63




Product Optocoupler

Pos. No 77Model / Type Ref. TCET110.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,


Product Optocoupler




Order No. 257066 /63




Product Optocoupler

Pos. No 79Model / Type Ref. EL263L.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics DUAL CHANNEL HIGH SPEED LOGIC GATE Minimum external creepage


Product Optocoupler




Order No. 257066 /63




Product Optocoupler

Pos. No 81Model / Type Ref. VO610A.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,


Product Optocoupler

Pos. No 82Model / Type Ref. VO615A.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,


Product Optocoupler




Order No. 257066 /63




Product Optocoupler



Product Optocoupler



Product Optocoupler




Order No. 257066 /63




Product Optocoupler


to 5.0mm, minimum internal creepage distance is measured to 4.0mm andminimum distance through insulation is measured to 0.4mm. Tested forreinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in110 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C.After the cycling test a humidity test for 48h in 93% relative humidity. Electricstrength test between input and output 4800Vac/1 minute. The symbol “.”in type designation may be blank, A~Z or numbers, and denote different pinshape. Maximum operating temperature: 110°C

Product Optocoupler



Product Optocoupler




Order No. 257066 /63




Product Optocoupler



Product Optocoupler

Pos. No 91Model / Type Ref. CNY17G.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,


Product Optocoupler

Pos. No 92Model / Type Ref. CNY75.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,



Order No. 257066 /63




Product Optocoupler

Pos. No 93Model / Type Ref. CQY80.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,

minimum internal creepage distance is measured to 6.0mm and minimumdistance through insulation is measured to 0.5mm. Tested for reinforcedinsulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degreeC, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After thecycling test a humidity test for 48h in 93% relative humidity. Electric strengthtest between input and output 4800Vac/1 minute.The symbol “.” in typedesignation may be blank, A~Z or numbers, and denote different pin shape.Maximum operating temperature: 110 degrees C.

Product Optocoupler

Pos. No 94Model / Type Ref. K233.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,


Product Optocoupler

Pos. No 95Model / Type Ref. TCDT110.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,



Order No. 257066 /63




Product Optocoupler



Product Optocoupler



Product Optocoupler

Pos. No 98Model / Type Ref. CNY75G.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 8.0mm,



Order No. 257066 /63




Product Optocoupler

Pos. No 99Model / Type Ref. CQY80.GTrade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 8.0mm,


Product Optocoupler

Pos. No 100Model / Type Ref. K233.GTrade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 8.0mm,


Product Optocoupler




Order No. 257066 /63




Product Optocoupler

Pos. No 102Model / Type Ref. TCDT110.GTrade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 8.0mm,


Product Optocoupler



Product Optocoupler




Order No. 257066 /63




Product Optocoupler

Pos. No 105Model / Type Ref. HS817.GTrade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 8.0mm,


Product Optocoupler

Pos. No 106Model / Type Ref. TCET110.GTrade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 8.0mm,


Product Optocoupler


to 7.7mm, minimum internal creepage distance is measured to 5.5mm andminimum distance through insulation is measured to 0.5mm. Tested forreinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in100 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C.After the cycling test a humidity test for 48h in 93% relative humidity. Electricstrength test between input and output 4800Vac/1 minute. The symbol “.” intype designation may be blank, A~Z or numbers, and denote different pinshape. Maximum operating temperature: 100°C


Order No. 257066 /63




Product Optocoupler


to 7.7mm, minimum internal creepage distance is measured to 5.5mm andminimum distance through insulation is measured to 0.5mm. Tested forreinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in100 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C.After the cycling test a humidity test for 48h in 93% relative humidity. Electricstrength test between input and output 4800Vac/1 minute. The symbol “X” intype denotes X = Part no. (1,2,3).The symbol “.” in type designation may beblank, A~Z or numbers, and denote different pin shape. Maximum operatingtemperature: 100°C

Product Optocoupler


to 7.7mm, minimum internal creepage distance is measured to 5.5mm andminimum distance through insulation is measured to 0.5mm. Tested forreinforced insulation. Thermal cycling test, 10 cycles. Each cycle: 68h in100 degree C, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C.After the cycling test a humidity test for 48h in 93% relative humidity. Electricstrength test between input and output 4800Vac/1 minute.The symbol “.” intype designation may be blank, A~Z or numbers, and denote different pinshape. Maximum operating temperature: 100°C


Order No. 257066 /63




Product Optocoupler

Pos. No 110Model / Type Ref. H11BX.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics PHOTODARLINGTON Minimum external creepage distance is measured


Product Optocoupler

Pos. No 111Model / Type Ref. H11B255.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics PHOTODARLINGTON Minimum external creepage distance is measured


Product Optocoupler




Order No. 257066 /63




Product Optocoupler

Pos. No 113Model / Type Ref. TIL113.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics PHOTODARLINGTON Minimum external creepage distance is measured


Product Optocoupler

Pos. No 114Model / Type Ref. MOC119.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics PHOTODARLINGTON Minimum external creepage distance is measured


Product Optocoupler




Order No. 257066 /63




Product Optocoupler



Product Optocoupler

Pos. No 117Model / Type Ref. EL4504.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics SINGLE CHANNEL HIGH SPEED TRANSISTOR(Non-Base Bonded)

Minimum external creepage distance is measured to 8.0mm, minimuminternal creepage distance is measured to 5.0mm and minimum distancethrough insulation is measured to 0.5mm.Tested for reinforced insulation.Thermal cycling test, 10 cycles. Each cycle: 68h in 100 degree C, 1h in 25degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test ahumidity test for 48h in 93% relative humidity. Electric strength test betweeninput and output 4800Vac/1 minute. The symbol “.” in type designationmay be blank, A~Z or numbers, and denote different pin shape. Maximumoperating temperature: 100 degrees C.


Order No. 257066 /63




Product Optocoupler



Product Optocoupler



Product Optocoupler




Order No. 257066 /63




Product Optocoupler



Product Optocoupler



Product Optocoupler

Pos. No 123Model / Type Ref. EL3H7.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler (SMD type). Minimum external creepage distance is measured



Order No. 257066 /63




Product Optocoupler



Product Optocoupler




Order No. 257066 /63




Product Optocoupler

Pos. No 126Model / Type Ref. MOC8020.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics PHOTODARLINGTON

Minimum external creepage distance is measured to 7.7mm, minimuminternal creepage distance is measured to 5.5mm and minimum distancethrough insulation is measured to 0.5mm. Tested for reinforced insulation.Thermal cycling test, 10 cycles. Each cycle: 68h in 100 degree C, 1h in 25degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test ahumidity test for 48h in 93% relative humidity. Electric strength test betweeninput and output 4800Vac/1 minute. The symbol “.” in type designationmay be blank, A~Z or numbers, and denote different pin shape. Maximumoperating temperature: 100°C

Product Optocoupler




Order No. 257066 /63




Product Optocoupler



Product Optocoupler

Pos. No 129Model / Type Ref. EL3H71.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler (SMD type). Minimum external creepage distance is measured



Order No. 257066 /63




Product Optocoupler



Product Optocoupler



Product Optocoupler




Order No. 257066 /63




Product Optocoupler


minimum internal creepage distance is measured to 6.0mm and minimumdistance through insulation is measured to 0.5mm. Tested for reinforcedinsulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degreeC, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After thecycling test a humidity test for 48h in 93% relative humidity. Electric strengthtest between input and output 4800Vac/1 minute. The symbol “X” in typedenotes X = Part no. (5,6,7,8). The symbol “.” in type designation may beblank, A~Z or numbers, and denote different pin shape. Maximum operatingtemperature: 110 degrees C.

Product Optocoupler




Order No. 257066 /63




Product Optocoupler


minimum internal creepage distance is measured to 6.0mm and minimumdistance through insulation is measured to 0.5mm. Tested for reinforcedinsulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degreeC, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After thecycling test a humidity test for 48h in 93% relative humidity. Electric strengthtest between input and output 4800Vac/1 minute. The symbol “X” in typedenotes X = Part no. (5,6,7,8). The symbol “.” in type designation may beblank, A~Z or numbers, and denote different pin shape. Maximum operatingtemperature: 110 degrees C.

Product Optocoupler

Pos. No 136Model / Type Ref. 4N2X.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,



Order No. 257066 /63




Product Optocoupler

Pos. No 137Model / Type Ref. 4N3X.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,


Product Optocoupler

Pos. No 138Model / Type Ref. MOC8050.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics RANDOM PHASE PHOTOTRIAC Minimum external creepage distance is



Order No. 257066 /63




Product Optocoupler

Pos. No 139Model / Type Ref. MOC8080.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics RANDOM PHASE PHOTOTRIAC Minimum external creepage distance is


Product Optocoupler

Pos. No 140Model / Type Ref. EL301X.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics RANDOM PHASE PHOTOTRIAC

Minimum external creepage distance is measured to 7.7mm, minimuminternal creepage distance is measured to 5.5mm and minimum distancethrough insulation is measured to 0.5mm. Tested for reinforced insulation.Thermal cycling test, 10 cycles. Each cycle: 68h in 100 degree C, 1h in 25degree C, 2h in 0 degree C and 1h in 25 degree C. After the cycling test ahumidity test for 48h in 93% relative humidity. Electric strength test betweeninput and output 4800Vac/1 minute. The symbol “X” in type denotes X =Part no. (0,1,2,3,4).The symbol “.” in type designation may be blank, A~Z ornumbers, and denote different pin shape. Maximum operating temperature:100°C


Order No. 257066 /63




Product Optocoupler



Product Optocoupler

Pos. No 142Model / Type Ref. EL253L.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics DUAL CHANNEL HIGH SPEED TRANSISTOR Minimum external creepage



Order No. 257066 /63




Product Optocoupler

Pos. No 143Model / Type Ref. MCT2.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,


Product Optocoupler

Pos. No 144Model / Type Ref. MCT2E.Trade mark (if different from page 1) Rating 250VrmsPrincipal characteristics Optocoupler. Minimum external creepage distance is measured to 7.7mm,

minimum internal creepage distance is measured to 6.0mm and minimumdistance through insulation is measured to 0.5mm. Tested for reinforcedinsulation. Thermal cycling test, 10 cycles. Each cycle: 68h in 110 degreeC, 1h in 25 degree C, 2h in 0 degree C and 1h in 25 degree C. After thecycling test a humidity test for 48h in 93% relative humidity. Electric strengthtest between input and output 4800Vac/1 minute. The symbol “X” in typedenotes X = Part no. (1,2,3,4). The symbol “.” in type designation may beblank, A~Z or numbers, and denote different pin shape. Maximum operatingtemperature: 110°C

certificate - everlight europe › img › cms › safety_certs › nemkop112… · nemko as...

Documents