ceragon - ip-10 quick startup guide - word.pdf

5/23/2018 Ceragon - IP-10 Quick Startup Guide - Word.pdf

1/12

FibeAir IP-10

Quick Startup Guide

Aug 2008


2/12

IP-10 Quick Startup Guide Doc Rev0.12

PROPRIETARY

Contents

1. DOCUMENT PURPOSE .......................................................................... ..................................... 3

2. DOCUMENT SCOPE..................................................................... ................................................ 3

3. STARTUP CONFIGURATION STEPS .................................................. ..................................... 3

3.1. LAUNCHING WEB-MANAGEMENT.................................................................. .......................... 4

3.2. IDUSOFTWARE UPGRADE.................................................................. ..................................... 5

3.3. LOADING LICENSE KEY........................................................................................................ .. 10

3.4 SAVING UNIT INFORMATION.11


3/12


PROPRIETARY

1. Document Purpose

The purpose of this document is to describe the basic configuration steps of IP-10radio link.

Refer to the IP-10 installation and management user guides for full configurationoptions.

2. Document Scope

This document describes the recommended initial steps in order to connect andmanage IP-10 radio link. It includes the configuration steps of the following mainsections:

Connecting to IDU using default factory setup

Launching the web management

SW Upgrade

License key activation

Basic parameters configuration

3. Startup Configuration Steps

Basic configuration includes the following basic steps:

1. Complete physical HW installation of IDU, IF coax cable, RFU and antenna as perinstallation instructions.

2. Connect PC to IDU and launch web management.

3. Upgrade IDU SW.4. Load license key.

5. Configure radio link parameters.

6. Complete link commissioning.


4/12


PROPRIETARY

3.1. Launching Web-Management

3.1.1 IDU factory Default Configuration

IP Address: 192.168.1.1, IP Mask 255.255.255.0.

Active management port: port #7 (far right RJ45 port), out-of band management.

License: Basic capacity 10Mbps, no ACM, Smart Pipe (only GbE ports, ports #1or #2)

SW package: Basic 1.1.1

Protection: Disabled. 1+0 configuration

3.1.2 Connecting to IDU

1. Verify no Ethernet traffic (cables or fibers) connected.

2. Power up IDU.

3. Connect PC to IDU management port (port #7, far right RJ45 port).

4. PC configuration: IP Address: 192.168.1.240, IP Mask 255.255.255.0, no defaultgateway.

5. Verify connectivity to IDU (ping 192.168.1.1). If no connectivity, verify IDU IPmanagement configuration using Command Line Interface (refer to Appendix).

3.1.3 Launching Web-Management

1. Open Internet Explorer.

2. Type IDU's IP address (192.168.1.1) on address field. IP-10 login screen will bedisplayed.

3. User: admin. Password: admin.


5/12


PROPRIETARY

3.2. IDU Software Upgrade

IDUs sent from production are loaded with basic SW version (1.1.1) that requires SWupgrade (via SW download) in order to support all system's features.

SW download is based on FTP. The IDU functions as an FTP-Client and externalFTP-Server software has to be installed and running on the PC storing the SWdownload files.

Customers may use Windows FTP-Server or any other FTP-Server freewareavailable.

3.2.1 Storing Download Files on PC

IDU SW files are Linux RPM files (14 files or more). The SW files are available fordownload from Ceragon's FTP site (zipped together as one SW package).

1. Download zipped SW package (for example, aidu-1.4.5.zip) from FTP and save itunder C:\updates.

2. Extract the aidu-1.4.5.zip to C:\updates.

3. Remove the aidu-1.4.5.zip file and store it in another location (for example, C:\IP-10).

4. Add to C:\updates folder any ODU/RFU file you may want to upgrade as well.

3.2.2 Installing FTP-Server Software

You may install and use any FTP-Server software for SW download. Ceragonrecommends using FileZilla_Server-0_9_26 software that can be downloaded fromthe web (freeware) or from Ceragon's FTP site.

1. Download zipped FileZilla_Server-0_9_26.zip from the internet or Ceragon's FTPsite and store it on the PC (for example, C:\IP-10).

2. Extract the file and run the installation setup. Follow installation process untilfinished (do not change any of the installation default settings).


6/12


PROPRIETARY

3.2.3 Initial Configuration of FTP-Server Software

After installing the FileZilla, it has to be configured to allow the SW download usingFTP.

Stopping Windows FTP services

In order to use FileZilla, Windows default FTP services have to be stopped.

1. Go to Control Panel> Administrative ToolsInternet Information Services, ifthe Internal Information Services dont appear its means that the Windows FTPwasnt install and you may have to proceed without doing so.

2. Use Right-Click to stop the Default FTP Site under FTP Sites.

Configuration of the FTP-Server software

User and files path have to be defined on the FTP-Server.

1. Launch the FileZilla Server Interface (go to FilesProgramsFileZilla ServerFileZilla Server Interface).

2. Click OK on the Connect to Server window. The FileZilla Server window will bedisplayed.


7/12


PROPRIETARY

3. Select EditUsersShared Folders. The Users window will be displayed.

4. Select Add on the Users section and enter anonymous in the Add user Accountwindow.

5. Select Add on the Shared Folders section and select local drive C:\ in the Browsefor Folder.

6. Select (check) Read, Write and Delete in the Files section.

7. Verify your configuration is identical to the displayed in the following window:


8/12


PROPRIETARY

8. Select OK and close the FileZilla server.Launching of the FTP-Server software

User and files path have to be defined on the FTP-Server.

1. Launch the FileZilla Server Interface (go to FilesProgramsFileZilla ServerFileZilla Server Interface).

2. Click OK on the Connect to Server window. The FileZilla Server window will bedisplayed.

3. Verify server is running (yellow lightning Bolton top-left corner highlighted andstatus is Logged On.


9/12


PROPRIETARY

3.2.4 SW Download Procedure

Once FTP-Server was configured and running, new SW package will be downloadedusing the web-management

1. Verify SW files stored at C:\updates.

2. Verify FTP-Server configured and running.

3. Verify Windows Firewall is disabled!!!

4. Connect to IDU and launch web-management.

5. Go to GeneralVersions and check the currently running aidu version to

determine if SW upgrade is necessary.

6. Go to Diagnostics & MaintenanceSoftware Management. The SoftwareManagement screen will be displayed:

7. In the Remote Server Parameters enter the remote FTP-Server details as perconfiguration above:

a. Remote SW Update server URL: ftp://xxx.xxx.xxx.xxx/updates/the IPshould be the hosts IP. meaning the Lap Top that the SW is beingdownload from

b. Remote server login: anonymous

c. Remote server password: leave blank

8. Select Download to start the SW downloads. This may take few minutes untilcompleted (this operation will download all files under C:\updates to the IDU butwill not activate them).

9. Select Upgrade to install the newly downloaded files. This may take few minutes

until completed.10. Restart the IDU once SW download and upgrade successfully completed.


10/12


PROPRIETARY

3.3. Loading License Key

IDUs sent from production are loaded with basic license:

License: Basic capacity 10Mbps, no ACM, Smart Pipe (only GbE ports, ports #1or #2)

Upgrading capacity of feature-set is done by manual entry of license key based on theIDU's Serial number.Contact Ceragon in order to obtain your license key.

1. Verify you have the license key matching the IDU Serial Number.

2. Connect to IDU and launch web-management.

3. Go to GeneralUnit parameters and verify the IDU's Serial number matches thelicense key.

4. Go to GeneralLicensing and enter the license key in the License Code field.

5. Restart the IDU.

6. Go to GeneralLicensing and verify the correct license parameters wereupdated.

7. You may use the Demo license (60 days) to have full capacity and feature-set.


11/12


PROPRIETARY

3.4 Save Unit Information

3.4.2 Open the IDU and go to: /Diagnostic & management/Configurationmanagement.

3.4.3 Go to Configuration management Parameters: and fill in as follows:Host IP - your computer IPHost Path - //User name anonymousUser Password - enter your laptop windows user name and apply.

3.4.4 Lunch FileZilla FTP Server and make sure its running (yellow Bolt)

3.4.5 Under Unit Information click on the Create Archive tab and wait tillthe browser will disconnect you from the IDU.

3.4.6 Re-Connect to IDU and go again to: /Diagnostic &management/Configuration management.

3.4.7 Under Unit Information click on the Upload Archive tab and watchthe FilleZilla FTP server screen and verify that all the files were sentto the path you have specified on the /FilleZilla/Edit/Users/SharedFolder.


12/12


PROPRIETARY

3.4.8 Go to /My Computer/C and look for a file name of xxx xxx.tar.tz and

extract it to where ever you choose.

3.4.9 After extracting it go to /Var/Lib/Aidc and the file name isdmae_tech.log

ceragon - ip-10 quick startup guide - word.pdf

Documents

ceragon ip

ip mask

quick startup guide

fibeair ip

andmanage ip

quick startup guide

quick startup guideaug

idu management port