celosia de aluminio

Jalousie with adjustable louvers - Jalousie with adjustable louvers - Jalousie with adjustable louvers - Jalousie with adjustable louvers - Jalousie with adjustable louvers - Jalousie with adjustable lou-

1 JX

JX1st quarter 2005

jalousie

Conception P. 3

Fabrication P. 45

Jalousie with adjustable louvers - Jalousie with adjustable louvers - Jalousie with adjustable louvers - Jalousie with adjustable louvers - Jalousie with adjustable louvers - Jalousie with adjustable lou-JX

2


Jalousie with adjustable louvers - Jalousie with adjustable louvers - Jalousie with adjustable louvers - Jalousie with adjustable louvers - Jalousie with adjustable louvers - Jalousie with adjustable lou-Jalousie with adjustable louvers - Jalousie with adjustable louvers - Jalousie with adjustable louvers - Jalousie with adjustable louvers - Jalousie with adjustable louvers - Jalousie with adjustable lou-

3 JX

Product concept P. 4

Performance P. 6

Inertia values P. 11

Applications P. 12 Frame with glass louvers P. 12 Clip recess frame with glass louvers P. 14 Frame with aluminium louvers P. 16 Clip recess frame with aluminium louvers P. 18 Combination frame with glass and alu louvers P. 20 Frame with aluminium louvers and JXb window unit P. 22 Frame with fly screen P. 24

Options P. 26

Infills P. 34

Installation P. 35

List of profiles P. 38

List of accessories P. 42

List of tools P. 44

References index P. 96

Conception

Jalousie


4


JX product concept Jalousie louver frame, 63 mm module

Square-cutassembledfixedframe. Openinglouversincurvedaluminiumorglassat

135 mm intervals. Hinging and protection ensured by overlapping

polyamide end caps enabling opening to 80. Weatherproofingensuredbymarine-quality

EPDM gaskets or polyethylen brush gasket. Stainlesssteelscrews. Operationbyleverhandle,turnhandleorknob DriverrodsinZamacalloy.

Options

Installationonsingleinsidesill. Installationoninsidesillwithselflocating

system. Flyscreen,removableforcleaning. Reinforcedsecurityby:

5 mm cross rod.

Height of frame according to number of louvers

*The conception and dimensions of the systems presented in this catalogue are in compliance with the French and / or European regulations applicable at the time of the realization of the document.

The aluminium fabricator and/or consultant are entitled to check if these conceptions and dimensions have to be adapted according to local legislation and all other relevant norms and standards.

2 mini 334 343 361 365 3 469 478 496 500 4 604 613 631 635 5 739 748 766 770 6 874 883 901 905 7 1009 1018 1036 1040 8 1144 1153 1171 1175 9 1279 1288 1306 1310 10 1414 1423 1441 1445 11 1549 1558 1576 1580 12 1684 1693 1711 1715 13 1819 1828 1846 1850 14 1954 1963 1981 1985 15 2089 2098 2116 2120 16 2224 2233 2251 2255 17 2359 2368 2386 2390 18 2494 2503 2521 2525 19 2629 2638 2656 2660 20 2764 2773 2791 2795 21 2899 2908 2926 2930 22 3034 3043 3061 3065

7791 7791

7792

7797 5

7792

7710

12 7657

7791

512 7657

7791

5

7797

5

Heightofframe Wallaperture with bottom with bottom with bottom with bottom transom 7792 transom 7797 transom 7792 transom 7797 Number

of

louvers


5 JX

Choice of maneuversaccording to dimensions

With1springset7719W0.80m

With2springsets77190.80m 1 m, use three 7626 hinges

(**) or W - 151 with 7621 rebate (***) or W - 167 with 7621 rebate N = Number of louvers H = (N x 135) + 64 with 7792or H = (N x 135) + 73 with 7797

Dim

ensi

on fo

r77

92 s

ingl

etra

nsom

Dim

ensi

on fo

r77

97 tr

anso

mw

ith c

ap

Dim

ensi

on fo

r77

09 s

ingl

ein

side

sill

sec

tion

Dim

ensi

on fo

r 42

mm

7793

sin

gle

uprig

ht s

ectio

n

Dim

ensi

on fo

r50

mm

779

5si

mpl

e up

right

Bill of materials Ref. Description Preparation Quantity Cutting formula 7620 Secondaryglazingsection 2H+2W H-18 H-27 H-34 W-69 W-85 7621 Rebate section 1H H - 77 H - 86 H - 93 7713 135mmaluminiumlouver NW W-100 W-116 7772 Capping section 2H H H H - 16 7791 Transom 1W W-84 W-100 7792 Transom(lowerpart) 1W W-84 W-100 7793 Uprightsection(42mm) 2H H H H-16 1197 Reversible manoeuvre set 1 1835 Driving head screw 4 x 25 14 3160 Deflector 2 3178 Weatheringdeflector 2 7622 Corner cleat set 4 7623 Lock for 7620 1 7624 5/6mmglazinggasket 2H+2W 7626 Hinge 2* 7627 Rebategasket 2H+2W 7701 Training body N 7705 Trainer bearing N x 2 7716 Aluminiumlouvergasket(7713) (N+2)W 7717 Bottom part plug 2 7718 Axis N x 2 7723 Rod set 2 7777 Plug 2 JV003 Uprightgasket 2H VE048 Driving head screw 4.8 x 55 N x 2

PRO

FIL

SA

CC

ESSO

RIE

SPR

OF.

Variants 7795 Uprightsection(50mm) 2H H H H-16 7796 Uppertransomarchitrave 1W W-84 W-100 7797 Bottom transom architrave 1W W-84 W-100 8400 Architrave 2H+2W H+51 W+51 8475 55mmflashingsection 1W W 1112 Stainlessclip 3/ml

2140 40 55,8

63,8

W

42

13

63

7626 7620 7627 7701 7713 76217624 7623 1835 119776227793ou 7795

7772

50

VE048JV003

JX009.C

Horizontalcrosssection,scale1/2

Closed position

(N - 1 x 135) + 30

15Haut

Bas 15

Dimension of rod linkage

Glass deductions JXb

with 7792 with 7793 H - 741 W-1251

with 7797 with 7795 H - 831 W-1411

Options 7657 Positionalrailsection 1W W W 7661 Flyscreensection 2H+2W H-67 H-76 H-83 W-87** W-103*** 7709 Sillsection 1W W 7710 Sillsection 1W W 7774 Insidesillsection 1W W 1370 Flyscreenspline 2H+2W 1403 Corner cleat (fly screen 4 7719 Gasket plug 1 7775 Bouchonpourprofilspicedappui 2x0,020

PRO

FIL

SA

CC

ESS.


23 JX

63

H

63 5

4940

135

135

H

150

190,5

40

1322

1835

7759

7713

7621

7716

7701

7792or 7797

7791or 7796

7622762776207624

3160+ 3178

1835

7759

7716

7713

7621

7701

7792or 7797

7791or 7796

7622762776207624

3160+ 3178

77177717

JX010.C

Verticalcrosssection,scale1/2 Verticalcrosssection,scale1/2

Closed position Opened position


24


Applications

Frame with fly screen


Closed position

JX011.C

2140 40 55,8

63,8

W

42

13

63

7620 76217795 ou 7793

50

76611370 1403

W42

43,551,5

63

76617795 or 7793

13701403

JX011.C

Dim

ensi

on fo

r50

mm

779

5

and

reba

te

sect

ion

7621

Dim

ensi

on fo

r42

mm

779

3 a

nd re

bate

se

ctio

n 76

21

Dim

ensi

on fo

r77

92 s

ingl

etra

nsom

Dim

ensi

on fo

r77

97 tr

anso

mw

ith c

ap

Dim

ensi

on fo

r77

09 s

ingl

ein

side

sill

sec

tion

Dim

ensi

on fo

r42

mm

7793

sin

gle

uprig

ht s

ectio

n

Dim

ensi

on fo

r50

mm

779

5si

mpl

e up

right

Bill of materials Ref. Description Preparation Quantity Cutting formula 2H H - 67 H - 76 H - 83 7661 Profilmoustiquaire 2W W-87 W-103

1370 Fly screen spline 2H + 2w 1403 Corner cleat (fly screen) 4

PRO

F.A

CC

ES. W-125 W-141


Closed position


25 JX

1370

7661

1403

7792or

7797

7791or

7796

H H

1370

7661

1403

7709or

7774

7791

7792

63 63

40,856,849,8

25,825,8

16

Verticalcrosssection,scale1/2 Verticalcrosssection,scale1/2

Closed position Opened position

JX012.B


26


Standard maneuver

VT009.00

Stopblock

1 - Turn the stop block untill it reaches its uppermost position.2 - Remove the spring.

3 - Unscrewthetwosrewsonthebackofthecasing.

4 - Turn the whole handle + end cap through 180.5 - Repeat the above operations in reverse order.

Reversing the maneuver

Handle1197


27 JX

Options

Choice of maneuver sets

JX011.A

KV046

Handle 1249 or 1268

Handle CV056

KV046

JX011.A


28


Options

Frame joint

Reinforcement of louver articulationsfor use as balustrade

JX013.A

7793

7677Technal sleeve(M5 x 30) 1809

Technal sleeve(M5 x 30) 1809

Threaded rod M5(no Technal)

7795 7711Technal sleeve(M5 x 30) 1809

1,2

101,2

39,7

7793 7711 VE046 VE047Technal sleeve(M5 x 30) 1809

1,2

39,7

Weathering W11085,2

26,2

110,2

7793 7772 VE046Technal sleeve(M5 x 30) 1809

2,4

39,7

Weathering W11086,4

Set page 9 for inertia of sections 7711, 7772 and 7677.

X X

XX X X

XX

Ixx = 41.90 cm4 I = 12.94 cm3

V

Ixx = 43.04 cm4 I = 13.28 cm3

V Ixx = 68.97 cm4 I =20.54 cm3

V

Ixx = 47.57 cm4 I = 14.46 cm3

V

7790VE037

7702

7718

Compulsory for use as balustrade.

1836

WithPerfopack2769 tool(see page 90)


29 JX

Options

Intermediate transom 7798(for glass louvers only)

JX014.A

135

18,6 21,6135

32,1

H

135

1835

7703 Glass louver trainer body 115 mm



7759

7798 Intermediate frame transom

Intermediatetransom for more than 11 louvers

Dimension of glass louver driver body 7703

H = 103

Intermediate transoms must be used in the case of multiple maneuvres.


30


Options

Adjustment of fixed frame

64

5

40

22 107

H

7620

7657

7661

7791

40

13

40

13

HH

77977792

Bottom transom 7792 Bottom transom 7797

40

13

1634

7792

7709

7774

H

Bottom transom 7792 on continuous sillsection 7709 or 7774

40

137792

7710

H

Bottom transom 7792 on continuous sillsection7710

5

Top

Bottom


31 JX

Options

Fixed frame with sill section and trim

8329 or 8395 or 8537 or 8334 or 8475

7796

7797

8400orFE016or8402or8404

8615or8617

1112

1112

8404 or 8402 or FE016 or 8400 7795

1112

8404or8402orFE016or8400


Verticalcrosssection,scale1/2


32


Options

Integration with PB door

30

7.21.8

FP0437787119777027790

W jalousie = W - 265

W

123.5

7791

7792

H ja

lous

ie =

H2

- 179

30

29

7787

FP043

1.8

7.2

h2

h1

H2

H1

Jalousie mustbe above the

handle

JV0037793FP003 CP004+ VE037

KP009

1020+ 1040

38.8656

46

3150

FP004 JP004 EE019



33 JX

30

7.21.8

FP0437787119777027790

W jalousie = W - 265

W

123.5

7791

7792

H ja

lous

ie =

H2

- 179

30

29

7787

FP043

1.8

7.2

h2

h1

H2

H1

Jalousie mustbe above the

handle

JV0037793FP003 CP004+ VE037

KP009

1020+ 1040

38.8656

46

3150

FP004 JP004 EE019


JX025.B

JX024.A


34


Infills

Choice of glazing gaskets

7624or7625

7670or7673or7654or7778

7624or7625

7670or7673or7654or7778

With glass louvers

With JXb opening frame

Thickness Gasket

5 mm to 6 mm

8 mm to 8.8 mm

7624

7625

Thickness Gasket

5 mm

5.5 mm

7670

7673

6 mm 7654

6.6 mm 7778


35 JX

Mounting options

Mounting on sill without clip recessindependent jalousie

Category 1 silicone sealant


Wedge

Wedge

8

7713

WWall opening width

JV00377957772

7791

7792

88

H

Wal

l ope

ning

hei

ght

VE048



JX101.C


36


Mounting on sill with clip recess independent jalousie

Mounting options

8

7713

W

7765779577728400

7796

8400

7797

8400

8475

88

H

JV003 VE048


Wedge

Wall opening width


Wedge

Wal

l ope

ning

hei

ght



JX103.C


37 JX

Situations de pose

Fitting on sill with single inside sill section7709 or outside sill section 7710 - Continuous

8

7713

W

JV00377957772

7791

7657

7792

7709W110

108

H

22

7792

7710

W110

8

H

VE048

265


Wedge

Wall opening width

Wal

l ope

ning

hei

ght

Wal

l ope

ning

hei

ght

Category 1siliconesealant

Wedge

Fastening by poprivet or screw

Plug 7775 to be positionedat each end and sealed

with W118.(Lengthofplug:20mm)

Category 1siliconesealant

Fastening by poprivet or screw



JX102.C


38


List of profiles

63

19

31

7791

63

19

31

7796

16

71.6

18

63

7709

46

73

44

63

7774

7792

16.4

5.2

13

63

46

16.4

22

63

55

5.2

7797

18.6

17

100

77105

15


39 JX

List of profiles

7713

17.4

132

27

14 x 14

17.2

28.5

14 x 14 41

7790

13

42

637793 7795 63

13

50

54.6

6.1

777254.6

12.6

7711

1.2 1.2


40


List of profiles

7620

39

16.1 7621

15.7

38

63

39.2

1.813.4 1.5 1.57787

7798

25

29.9

28.6

46

7677 67

52.8

26.2

63

66.8

64

21.9

7657

31

15.5

15.5

12.2 1.8

7661

8.2x12.5

6.6

7662

FP043


41 JX

List of profiles

6

6

64

75

5039.4

5.25

84048402FE016840035

55

208475

71.7

30

8334

115

20 8395

47.5

60

8615

47.5

85

8617

20

155.7

8329

20

109.7

8537


42


1197Reversible maneuver set

1112 Stainlessclip

76258/8.8 mm glazinggasket

1403Corner cleat(fly screen)

1809M5 x 30 sleeve(90- head milled)

7627 Rebate gasket

76546 mm glass lou-ver gasket3160 Deflector

76705 mm gasket for glass louver

7673Glass louver gas-ket(5,5mm)

7701 Training body

7702 Trainer body

7703 Trainer body

3178Weatheringdeflector1249

Left maneuver with lever

7622 Corner cleat set1268Right maneuver with lever

7623 Lock for 76201370 Fly screen spline

76245/6 mm glazinggasket

List of accessories

1836

Driving head screw5 x 25

Driving head screw4 x 251835 Hinge7626 7705 Trainer bearing


43 JX

VE048

Driving head screwHZ4.8x55-50

List of accessories

7775 Gasket plug

7759Uppertransomgasket

7724

7777 Plug

7778

VE037SelfdrillingscrewSR24,2x22

7723

7716Aluminuim louvergasket (7713)

7717 Bottom part plug

7718

7719 Springset

W110Smalljointsealant

W118 Siliconcartridge

W200Cyanoacrylate glue for gaskets

CV056 Turn handle

6.6 mm glazinglouver gasketAxis

ScrewTF90M5 x 90VE047

VE046ScrewTF90M5 x 70

Louver window rodW:5.38lm

Rod setL:1.38ml

FV086

50 mm pre-drilledupright profileL:5.72ml

FV085

42 mm pre-drilledupright profileL:5.70ml

7765 Louver gasket

KV045

Connecting part (VT) for CV056 handle

CV057Insert for transom fixation

KV046

Nut set forlever handle1268

JV003 Uprightgasket

CV058Insert (VT) for CV056 handle


44


List of tools

2762Perfopack forupright sections

2765Perfopack for capping section

2763Perfopack forupright sections

2773Perfopackfor 1403

2764Perfopack for handles

2779

Perfopack for secon-dary glazing section 76202766

Combinedpunch/die

2767Combinedpunch/die

2768Combinedpunch/die

Trimmingoffins,punchingforfixingholes and drainage.

Punchingofhole,attachmentandinter-mediate transom.

Punching for JX jalousie handles (for use with punch 2766,2767 or 2768 only).

Punching for slots on cappingsection 7772.

Machining for handle 1197.

Machining for handle 1268 and 1249.

Machining for handle CV056.

2769

Perfopack foraluminium/glass louvers

Punching of ends of aluminium louvers 7713 and glass louver bearers 7790.

2786

Autonomous toolfortransoms,architravesand outside sills

2788Perfopack forprofiles

Drainage at the ends of transoms/fixed frames 7797 or 7792,punchingofarchitravesandoutsidesills,drainagein the middle of transoms/fixed frames 7709 or 7774.

Cutting of notches in upright section 7793 or 7795,cappingsection7772,connection section 7711 and 7787.

For corner cleat 1403.

Punching for hinges 7626,for corner cleat set 7622 and lock 7623.


45 JX

Machining P. 47

Assembly P. 59

Machining of JXb window unit P. 73

Assembly of JXb window unit P. 77

Tool instructions P. 84

Fabrication

Jalousie


46


Machining

Summary of machining and assemblyoperations

OptionJX

JA

LOU

SIE

FRA

ME

JXb

WIN

DO

W U

NIT

Nop. Sequence Page 1 Preparation of sections (see applications) . 47 2 Trimming of fins of upright section 7793 or 7795 . . . . . . . . . . . . . . . . . . . . . . . 47 3 Machining of upright section 7793 or 7795 for connection of transoms. . . . . . . . . . . . . 48 4 Machining of upright section 7793 or 7795 for drainage . . . . . . . . . . . . . . . . . . . . . . . . 49 5 Machining of upright section 7793 or 7795 for hinging of drivers . . . . . . . . . . . . . . . . . 50 6 Machining of upright section 7793 or 7795 for handles . . . . . . . . . . . . . . . . . . . . . . . . . 51 7 Machining of capping section 7772 . . . . . . 52 8 Machining of drainage of bottom part 7792 or 7797 . . . . . . . . . . . . . . . . . . . . . . . 53 9 Machining for sill section 7709 or 7774 . . . 54 10 Machining for sill section 7709 or 7774 . . . 55 11 Machining of outside sill section 8475 or 8334 and architrave 8400 or 8402 . . . . . . . 56 12 Machining of upright section 7793 or 7795 for intermediate transom . . . . . . . . . . 57 13 Machining of glass louver bearer 7790 or aluminium louver 7713 . . . . . . . . . . . . . . . . 58 14 Cutting and machining of fly screen section 7661 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 15 Assembly of frame . . . . . . . . . . . . . . . . . . . 59 16 Fitting of plugs . . . . . . . . . . . . . . . . . . . . . . 60 17 Assembly of maneuver set with reversible handle 1197 . . . . . . . . . . . . . . . . 61 18 Assembly of left maneuver with lever handle 1249 or right maneuver with lever handle 1268 . . . . . . . . . . . . . . . . . . . . . . . . 62 19 Assembly of maneuver with turn handle CV056 . . . . . . . . . . . . . . . . . . 63 20 Assembly and mounting of glass louvers. . 64 21 Assembly and mounting of aluminium louvers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 22 Assembly and mounting of glass louvers. . frame and aluminium louvers frame. . . . . . 66-67 23 Mounting of spring set 7719. . . . . . . . . . . . 68 24 Fitting of capping section 7772 . . . . . . . . . 69 25 Fitting of deflector 3160 . . . . . . . . . . . . . . . 70 26 ChangeofhandleforAfterSalesServices 71 27 ChangeofglassforAfterSalesServices . 72

Nop. Sequence Page 1 Preparation of sections (see applications) . 73 2 Machining for hinge 7626 on secondary glazing section 7620 . . . . . . 73 3 Punching for corner cleat 7622 on secondary glazing section 7620 . . . . . . 74 4 Machining for connection of hinges 7626 on upright section 7793 or 7795 . . . . . . . . 75 5 Machining of strike plate on rebate section 7621 or secondary glazing section 7793 or 7795 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 6 Assembly of JX jalousie shutter . . . . . . . . . 76 7 Mounting of gasket 7624 or 7625 on the glass . . . . . . . . . . . . . . . . . . . . . . . . 76 8 Assembly of opening frame . . . . . . . . . . . . 77 9 Adjustments . . . . . . . . . . . . . . . . . . . . . . . . 78 10 Mounting of rebate gasket 7627 by clipping . . . . . . . . . . . . . . . . . . . . . . . . . 79 11 Mounting of hinge body on upright section 7793 or 7795 . . . . . . . . 79 12 Mounting of strike plate for lock 7623 on rebate section 7621 . . . . . . . . . . . . . . . 80 13 Mounting of rebate section 7621 on upright section 7793 or 7795 . . . . . . . . 81 14 Mounting of JXb frame on JX jalousie structure . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 15 Fixing of lock 7623 . . . . . . . . . . . . . . . . . . . 83


47 JX

Machining

1 - Preparation of sections

2 - Trimming of fins of upright section 7793 or 7795

7793or

7795

63

4250

20

40 if 779249 if 7797

Bottom

Top

Accordingtodescription,squarecut

WithPerfopack2762

JX019.B


48


Machining

3 - Machining of upright section 7793 and 7795 for connection of transoms

WithPerfopack2762

7793or

7795

63

4250

20 if 779229 if 7797

31 12

314 holes 4.2

12

15.5

Bottom

Top

JX019.B


49 JX

Machining

4 - Machining of upright section 7793 and 7795 for drainage

WithPerfopack2762

46 if 779255 if 7797

Bottom

Top

12 18

R 4

7793or

7795

63

4250

JX019.B


50


Machining

5 - Machining of upright sections 7793 and 7795 for hinging of drivers

WithPerfopack2763

7793or

7795

63

4250

49

251.5

150

135

N x 135=

=

Bottom

Top

N holes 16.6

Fixing holes 6 F/90

JX019.B


51 JX

Machining

6 - Machining of upright sections 7793 and 7795 for handles

WithPerfopack2764

Machining for1197 maneuver set

Machining forCV056 handle

Machining for1268 or 1249 maneuver set

7793or

7795

and 2766 punch/die set

or 2767punch/die set

or 2768punch/die set

7793or

7795

7793or

7795

60

11

11

16

3.5

R 2

15.7

1410.7

17.7

6

14.2

9.2 29.2

7.2 21

54

22

22

142

Holecenter 16.6

Holecenter 16.6

10

10

3.5

5.2

R 3

R 5

Bottom

Top

Bottom

Top

Bottom

Top

32

28.5

16.2

JX019.B


52


Machining

7 - Machining of capping section 7772

WithPerfopack2765

135

135

7772

54

102

N x 135

19.67

17.517.5

R 3.5

JX024.A


53 JX

Machining

8 - Machining of drainage of bottom part 7792 or 7797

6

6.3

7792 or 7797

30= =

30

7792 or 779720 ==45

6

80

5.54.28 17

20 ==45 80

6

5.54.28 17

30 ==

30

With2786 autonomous tool

a - Machining for drainage

b - Machining for deflector 3160 + 3178


54


Machining options

9 - Machining for sill section 7709 or 7774

6

16

7792

30= =

30

30 ==

30

20 ==

7709 or 7774

45

3.7

8

80

7.5

4.220 ==45 80

==


a - Machining of the 7792 transom for drainage

b - Machining of the sill section 7709 or 7774fordeflector3160 + 3178


55 JX

Machining options

10 - Machining for sill section 7709 or 7710 or 7774

13.110.210.213.1

2.4 3 2.4 2.4 3

bottombottom

Left upright Right upright

top top

2.4

7793or

7795

top

bottom3

31.8

=

=

66

7772

7711

top

bottom3

31.8

=

=

66

7787

WithPerfopack2788

b - Machining of cap section 7772 or connecting section 7711

c - Machining of connecting section 7787 (not for PB door integration)

a - Machining of 7793 and 7795 upright


56


Machining options

11 - Machining of outside sill section 8475 or 8334 and architrave 8400 or 8402

66 130

66Mitre cut

Square cut

130

8475 or8334

8400 or8402

66 130

8400 or8402


a - Punching of transom 8475 or 8334

b - Punching of architrave 8400 or 8402


57 JX

Machining options

12 - Machining of upright section 7793 or 7795 for intermediate transom

With2763 tool

7793or

7795

63

4250

18.6 21.6

4.2 32.1

Bottom

Top

JX019.B


58


Machining option

14 - Fly screen section 7661

13 - Machining of glass louver bearer 7790 or aluminium louver 7713 for connection of drivers

7661

7661 1403

a - Mitre cut

b - Punching with Perfopack 2773 tool

WithPerfopack2769

12

187713 R 2.1

617.2

7790

==

17.2 =

=

R 2.1

64.2

4.2

Compulsory for louverswider than 1 m.


59 JX

Assembly

15 - Assembly of frame

a - Setupthegasket7759 into top transom 7791 or 7796.

b-SetupthegasketJV003 on uprights 7793 or 7795.Whenassemblingtransomsand louvers,turntheliptowardtheinside. Set up the gasket 7765 on the bottom transom 7792 or 7797.

c - Setuptheplug7777 into the transom 7792 or 7797.(see page 60)

d - Fit the upright sections to the transoms using screws 1835 ,havingfirstmadetheendsofthe top and bottom transoms watertight with mastic W110. Ensure weatherproofing in the recess of the upright sections.

1835

7791 or 7796

7793or7795

7792or7797


60


Assembly

16 - Fitting of plugs

7777

7793or 7795

7777Uprightsectiondrainage hole

7793or 7795

7775

7709 or 77741 - Cut 20 mm of plug section 7775 for each end of the inside sill section.

2 - Setuptheplugsintothe sill section.

3 - Make watertight with mastic W110.

Plug 7717

7792 or 77975

1 - Setuptheplug 7777 (on to 5 cm maxi).2 - Make watertight with mastic W110 through the hole of upright 7793 or 7795.

On uprights 7793 or 7795

On 7709 or 7774 sill sections

JX011.A

JX001.A

On bottom part 7792 or 7797


61 JX

Assembly

17 - Preparation of maneuver set with reversible handle 1197

Axis to crimp to rod 7723before mountingCheck the partsare fitted together correctly

Average position byinterlocking in the slot

Axis to crimpon pulling part

30

7793

1197

7723

JX020.A


62


Assembly

The handle is fitted after thelouver hinging rods are put

in place.

1249or

1268

7723

Counterdrill6.5 mm

7793

KV046

KV046

JX003.A

18 - Preparation of left maneuver with lever handle 1249 or right maneuver with lever handle 1268


63 JX

Assembly

19 - Preparation of maneuver with turn handle CV056

1 - Mount the driver on the existing holes using the screws and nuts supplied.

2 - Position the insert.

3 - Slotthehandleinplaceandlineup the pin and the notch of the driver.

4 - Fix the handle in place with the screws supplied.

5 - Fit the screw covers.

7793

7723

CV0561

2

3

4

5

JX002.A


64


Assembly

7791 or 7796

7702

W110on ends of

louvers only

7793or

7795

7759

7790

7670

7792 or 7797

1 - Setupthegasket 7759 into the groove in top transom 7791 or 7796.

2 - Setupthegaskets 7765 into the grooves in glass louver bearer 7790 (except top louver) and bottom transom 7792 or 7797.

4 - Fit drivers 7702 to each end of the glass louver assemblies, gluing into place using small joint sealant W110 on only 2 cm at each end of the louvers.

3

3

JX009.A

20 - Assembly and mounting of glass louvers


65 JX

Assembly

21 - Assembly and mounting of aluminium louvers

7791 or 7796

7701

7793or

7795

7759

7713

1 - Setupthegasket7759 into the groove in top transom 7791 or 7796.

2 - Setupthegaskets7716 into the grooves in aluminium louvers bearer 7713 (except top louver) and bottom transom 7792 or 7797.

3 - Fit drivers 7701 to each end of the aluminium louver assemblies, gluing into place using small joint sealant W110 on only 2 cm at each end of the louvers.

3

7792 or 7797

W110on ends of

louvers only

JX008.A


66


Assembly

1

1-Startfromthebottomlouver.2 - 1 Put the louver in front of the holes of the lateral sections.3 -Setintheaxis7718 by clipping. 1 2 4 -Setintheotherlouversinthesameway.5 - Place the rod set 7723 in the axis. 3 6 - Then fix with the screws VE048 and the washer included with the rod set 7723 (whenspring:seepage68).7 - Check the right move of each louver (without lock).

22 - Standard mounting of aluminium and glass louvers


67 JX

2

3

Axis 7718

Rod set 7723

ScrewVE048


68


Assembly

23 - Mounting of spring set 7719

JX021.A

1 - Position support A on the first upper link arm B and screw it to the hinging axis.2 - Fasten the spring between the support A and next upper link arm.

See table of use page 5.

7719

779342

39,8

63

A AB

It is better to position the spring in the middle of the height of frame.


69 JX

Assembly

24 - Fitting of capping section 7772

Clip in place capping section 7772 (reversible on upright sections 7793 or 7795).

7793or

7795

7772

7791or

7796

No attachment holesin front of the spring

or handle.


70


Assembly

25 - Fitting of deflector 3160

1 - Position the deflector.2 - Clip the deflector and outflow valve to the sill section.

1 - Position the deflector.2 - Clip the deflector and outflow valve to the bottom transom.

7709or 7774

7792

7792or 7797

3160Deflector

3178Outflow valve

3160Deflector

3178Outflow valve

On bottom part 7792 or 7797

On sill section 7709 or 7774

JX001.A


71 JX

Assembly

26 - Change of handle (for After Sales Services)

Former handles 1500 (VT) and 7780 (JX) on existing frames may be replaced by the new handle CV056.Inthiscase,useonlythelatchkey, don't use the driver(see above).

CV056

Do not use


72


Assembly

27 - Change of glass for glass louvers frame (for After Sales Services )

1 - Setupthegasket.

2 - Soaptheoutsideofthegasket.

3 - Sliptheglassbetweenthetwotrainerbodies,usetwowoodwedges to adjust the glass.

4 - Whentheglassisintherebate,withdrawthewoodwedgesandmake the sealant for each trainer body.

3

4

1

3

gasket7670

trainer body7702

trainer body7702

glass louverbearer profile

7790

wood wedgewood wedge


73 JX

Machining of JXb window unit

1 - Dimension of secondary glazing section 7620

Mitre cut

2 - Machining for hinge 7626 on secondary glazing section 7620

WithPerfopack2779

31

120mini

Formanualoperation,trim at the reference line

7620

VT010.00


74



3 - Punching for corner cleat 7622 on secondary glazing section 7620

43,7

643,7

6

7620

WithPerfopack2779

VT068.00


75 JX


4 - Machining for hinges 7626 on upright section 7793 or 7795

a) Position the clamps supplied with Perfopack 2279 in the cutouts of secondaryglazing section 7620,thenclamp.

b) Punch side upright section 7793 or 7795,stillfittedwiththeclamps,usingPerfopack 2779.

Position the secondaryglazing section flush withthe side upright section

Top

13Clamps

7620

7793or 7795

4.5

19

43.5

JX010.A


76


Machining and assembly of JXb window unit

6 - Assembly of JX jalousie shutter

7 - Mounting of gasket 7624 or 7625 on the glass

Hp(to be definedaccording tothe jalousiemaneuver

minimum 10 cm)

48 28

5.5

4.5

4.5

16.6

76217621

= =

4(every 30 cm)

WithPerfopack2779

JX022.A

5 - Machining of the strike plate on rebate section 7621

7624:5to6mm-7625:8to8.8mm


77 JX

Assembly of JXb window unit

8 - Assembly of secondary opening frame

Setupthehingebodies into placebefore assembly(remove the pinduring mounting).

Setuplockthe7623 intoplace before assembly.

Screwcornercleats7622 firmly into placeusing a 3 mm allen keywith spherical head.

Note:

CHOICE OF OPENING DIRECTION

Reversing the lock :a)Undothesetscrewinelement1.b) Remove elements 1, 2 and 3 from the pin.c) Replace elements 2, 3 and 1 on the pin.d) Re-tighten the set screw (element 1 must be flush with the pin).

Right opening Left opening

3

2

1

2

3

1

7622

VT015.00


78



9 - Adjustments

0.5 mm

Adjust the diagonals using the 4nylon screws on the corner cleatsand bring the other 4 into contactwith the glass.

Position the hinge bodyinside the machining

DETAIL

VT017.00


79 JX


10 - Mounting of rebate gasket 7627 by clipping

11 - Mounting of the hinge body on upright section 7793 or 7795

JX005.A

Screwthehingeintotheinsertusing a 3 mm allen key


80



12 - Mounting of strike plate for lock 7623 on rebate section 7621

JX006.A

a)Setupthestrikeplatenutintothegrooveofrebatesection 7621.b)Screwthestrikeplateontothestrikeplatenut.

a

b

7621


81 JX


13 - Mounting of rebate section 7621 on upright section 7793 or 7795

JX007.A

- Counterdrill section 7793 or 7795 at 3.2 mm .- Mount rebate section 7621 by screwing into the jalousie frame.

1835

7621

7793or7795


82



14 - Mounting of JXb frame on JX jalousie frame

JX023.A

a) Bring the two hinge halves together.b)Withtheframeintheopenposition,setupthehingepinsintoplace,asshownin the diagram.

H - 68

H - 68


83 JX


15 - Immobilizing of lock 7623

7620

7623

Heightof strike

7621on jalousie

VT016.00

a)Adjusttheheightofthelockwithrespecttothestrikeplate,asshowninthediagram.b) Tighten the two set screws using a 3 mm Allen key.


84


SPARE PARTS

General

-Weightoftool:12.5kg- Operators must familiarize themselves with theseinstructions before setting up or using the tools.- Perfopack can only be used on Technal pressesref. 2700 or 2701.- Cutting parts may be subject to standard exchange(ref. under F...).

IMPORTANT:Lubricate punches every 20 cuts with W540.

TRIMMING OF FINS

XStopblock 1

X = 20 mm on top X = 40 mm on bottom with transom 7792 X = 49 mm on bottom with transom 7797

To trim fins by 20 mm push stop 2 To trim fins by 40 mm push stop 1 and remove stopTo trim fins by 49 mm remove stops 1 et 2

First

Second-Insertthesectionfromthefrontuntilthestop,thenpunch.

F339F338

Stopblock

F340

Stopblock 2

Tool instructions

Perfopack 2762 for machiningupright sections


85 JX

PUNCHING OF FIXING HOLES ON TOP SECTION

31 12

15.5

TOP

7793 or 7795

4.2

-Insertthesectionfromtherightofthetool,untilthestop,thenpunch.

PUNCHING OF FIXING HOLES AND DRAINAGE ON THE BOTTOM PART

-Insertthesectionfromthefrontuntilthestop,thenpunch.

form

er p

unch

2nd

punc

hing

20

mm

offs

et

Put

a 2

mm

wed

ge b

etw

een

tool

and

form

er p

unch

Position forleft-handupright

PUNCHING FOR THE WEATHERING OF THE PLUG 7717

BOTTOM

20 o

r 29

(with

779

7)

46 o

r 55

(with

779

7)

31 12

12 18

R4

4.2

BOTTOM

Position forright-hand

upright


86


Pull knock Indexation

StopblockF341

F342

General

- Weightoftool:18kg- Operators must familiarize themselves with theseinstructions before setting up or using the tools.- Perfopack can only be used on Technal pressesref. 2700 or 2701.- Cutting parts may be subject to standard exchange(ref. under F...).


SPARE PARTS

FITTING THE STOP TO THE TOOL- Fit the stop using the CHc screws provided.

PUNCHING OF HINGING HOLESPunching of hinging holes starting form the bottom of the uprights

- Lower the indexing lever and pivot it so that it locksin the lower position.- Raise the stop to the intermediate position to start at159mmfromthebottomofthesection,ortothehighposition to start at 150 mm from the bottom of thesection.- Insert the section from the left of the tool until thestop,thenpunch.

every 135 mm

16.6

BO

TTO

M 150 for 7792 159 for 7797

Punching along the length

- Lower the stop.- Locate the indexation to the right of the 16.6 mm hole already punched.- Punch.- Repeat this operation to punch along the lengthof the section.

16,6

Tool instructions

Perfopack 2763 for punching hingingand attachment holes


87 JX

PUNCHING OF COUNTERSUNK FIXING HOLES

- Position the drawer at the centre of the slot.- Insert the section from the left of the tool and positiona hinging hole at the fixed index mark.- Punch.

67.5 67.5

16.6 16.6 12

PUNCHING OF FIXING HOLES FOR INTERMEDIATE TRANSOM 7798- Position the drawer to the right of the slot for machiningtheleft-handuprightsection,andtotheleftoftheslotformachining the right-hand upright section.- Insert the section from the left of the toll and position ahinging hole at the fixed index mark.- Punch. 32.1

21.6

18.6

4.2


88


2764 : BASE FOR PUNCHINGOF JX JALOUSIE HANDLES

General

-Weightoftool:16kg- Operators must familiarize themselves with theseinstructions before setting up or using the tools.- Perfopack can only be used on Technal pressesref. 2700 or 2701.- Cutting parts may be subject to standard exchange(ref. under F...).


It is imperative to assemble the Perfopack 2764 toolwith a combined punch/die : ref. 2766, 2767 or 2768.

- Insert the section into the tool.- Push an index into the 16.6 mm hole already punched.index D for the right-hand upright.index G for the left-hand upright.- Punch.

Uprights 7793 or 7795

1410.7

16.2

hole

axi

s

16.

6

1014

210

R 5

217.2

machiningfor handles

1268 or 1249

7

6011

11

R 2

29.29.2

15.716

machiningfor handle

1197

28.5

6

2764 2764

32

5.2

14.2

6

R 3

machiningfor handle

CV056

2222

54

8

17.72764

BOTTOM BOTTOM BOTTOM

hole

axi

s

16.

6

3.5

3.5

2766Punch/die

2767 Punch/die

2768Punch/die

2766Punch/die

forhandle 1197

2767Punch/diefor handle

1268 and 1249

2768Punch/diefor handle

CV056

MACHINING

SETTING UP THE TOOL1- MOUNTING OF COMBINEDPUNCH/DIE

2- FASTENING 3- MOUNTING OF STOPS

Insert the punch/diefrom the front

Tighten the twoM8 x 45 screws

hole

axi

s

16.

6

Tightenthe twoM8 x 30screws

Position thetwo stops on thefront of the tool,then tighten theM6 x 35 screws

Tool instructions

Perfopack 2764 with punches 2766 or 2767 or 2768 for machining of handles


89 JX

SPARE PARTS

Stopper

Adjustable stopper

F337

General

- Weightoftool:13kg- Operators must familiarize themselves with theseinstructions before setting up or using the tools.- Perfopack can only be used on Technal pressesref. 2700 or 2701.- Cutting parts may be subject to standard exchange(ref. under F...).

IMPORTANT:Lubricate dies and punches every 25 cuts with W540.(Ineverycases,lubricateeachweek if tool is not use.)

PUNCHING OF 54 x 7 SLOTS ON CAPPING SECTION REF. 7772

- Pull the adjustable stopper.- Insert the section from the right ofthetool,untilthestop,thenpunch.

- Push the stopper back into place.- Insert the section and position thelast slot in the stopper of the tool.- Punch.- Repeat this operation along thelength of the section.

Adjustable stopper

54

17.5

17.5

7772

19.6

7

102 135 135

Note :

If you do not wish to punch the entire length of the section, simply mark the centre of the slot to be cut on the section,then align your mark with the reference lines and punch.

Tool instructions

Perfopack 2765for machining of capping section 7772


90


SPARE PARTS

Left and right punches

F479:Leftandrightpunches

Left and right dies

F480:Leftandrightdies

General

-Weightoftool:5.4kg- Operators must familiarize themselves withthese instructions before setting up or usingthe tools.- Perfopack can only be used on Technalpresses ref. 2700 or 2701.- Cutting parts may be subject to standardexchange (ref. under F...).

IMPORTANT:Lubricate dies and punches every 25 cuts with W540.(Ineverycases,lubricateeachweek if tool is not use.)

PUNCHING OF 6 x 4.2 AT THE ENDS OF THE ALUMINIUM LOUVER 7713AND GLASS LOUVER BEARER 7790

18

7713

R 2.16

4.217.2

12

7790

4.2==

==

==

R 2.16

17.2

= =

- Position and hold the section against the stopper.- Punch.

Tool instructions

Perfopack 2769for punching of aluminium louver 7713 and glass louver bearer 7790


91 JX

Position6

Position

2

Position5

Position4

Position4

Position5

Position3

Position1

SPARE PARTSF481 Dies Position 1F482 Punches Position 1 or 2F483 Dies Position 2F484 Dies Position 3F485 Punches Position 3F486 Dies Position 4F487 Punches Position 4F488 Dies Position 5F489 Punches Position 5F490 Dies Position 6F491 Punches Position 6General

- Weightoftool:54kg- Operators must familiarize themselves with theseinstructions before setting up or using the tools.- Cutting parts may be subject to standard exchange(ref. under F...)

IMPORTANT:Lubricatediesandpunchesevery25cutswith W540. (In every cases,lubricate each week if tool is not use).

A - DRAINAGE 30 x 6 1 - "Type C" drainage at each end of the sill section (position 5)


Machining both edges

30

30

6.3 6 6.3 6

77927797

Type C Type C

2 - "Type D" "drainage at each end of the sill section (position 6)- Position and hold the section against the stopper.- Punch.

Machining both edges30

3016

16

66

77927797

Type D Type D

Tool instructions

Autonomous tool 2786for drainage of transoms/fixed frames andmachining of architraves and outside sills


92


B - DRAINAGE FOR DEFLECTOR 1 - "Type B" drainage at each end of the sill section (position 4)


20= =

80 45

Machining both edges

= =

4.20.4

6

5.5

77977792Type B

2 - "Type A" drainage at each end and in the middle of the sill (position 3)

- Insert the section into the tool.- Align the reference mark on the section with the reference mark on the tool.- Punch.

80 45

20

Machining both edges and the middle of the barre

= =

= =

4.2

3.7

7.58

770977737774

Type A

C - PUNCHING OF OUTSIDE SILLS 1 - 66 mm cut at each end of the sill (position 1)

- Insert the section into the tool until the stop.- Push the sill section against the stop in the left-hand positionto punch the left-hand end.- Punch.- Repeat the operation with the stop in the right-hand positionto punch the right-hand end.

Referenceline

Mark on the section

2 - 130 mm cut in the middle of the sill section (position 1)

- Insert the section into the tool.- Align the reference mark on the section with the reference mark on the tool.-Holdthesectioninpositiononthetool,thenpunch.-Aftermakingthefirstcut,movethesectionaround65mmtotheleftsothatthestopindexesinthefirstcut,thenpullslightlytotherightsothatthe edge is against the stop.-Holdthesectioninpositiononthetool,thenpunch.- Deactivate the stop and remove the section.

This operation is carried out in two successive cuts of 65 mm,using the first cut as an index for the second.

8334

8475

2.3

2.3

Mark on the section

130= =

66

Left position block

Right position block

65 mm

Push for disconnectthe stop block

Referenceline

Mark on the section

Stopblocktomatch with

the firstmachining

Tool instructions

Autonomous tool 2786 (continued)


93 JX

130 8400 8402

8400 8402

= =66

130= =

66

Mark on the section

D - PUNCHING OF ARCHITRAVE 1 - 66 mm cut at each end of the architrave (position 2)

-Setupandblocktherightorleftstoppertoholdthesectionagainst the stopper.- Position the section on to the stopper.- Punch.- Deactivate the first used stopper and use the second stopper.- Position the section on to the second stopper.- Punch.

Left stopperon line

Stopblocktomatchwiththe first machining

Adjustment

Markon the section

Referenceline

Right stopperdeactivated

2 - 130 mm cut in the middle of the architrave (position 2)

- Insert the section into the tool.- Align the reference mark on the section with the reference mark on the tool.-Holdthesectioninpositiononthetool,thenpunch.-Aftermakingthefirstcut,movethesectionaround65mmtotherightsothatthestopindexesinthefirstcut,thenpullslightlytotheleftsothattheedgeis against the stop.-Holdthesectioninpositiononthetool,thenpunch.- Deactivate the stopper and remove the section.

This operation is carried out in two successive cuts of 65 mm,using the first cut as an index for the second.

Mark on the section


94


F492UprightdiePosition1F493UprightpunchPosition1F494 Punch/die Position 2F495 Punch/die Position 3

SPARE PARTS

10.210.213.1

2.4 3 2.4 2.4 3

7793

7795

7793

7795

bottom of sectionbottom of section

LEFTUPRIGHT RIGHTUPRIGHT

top of section top of section

2.4

General

-Weightoftool:8kg- Operators must familiarize themselves with theseinstructions before setting up or using the tools.- Cutting parts may be subject to standardexchange (ref. under F...)

A - CUTTING OF 2.4 x 3 NOTCHES ON RIGHT AND LEFTUPRIGHTS 7793 or 7795 (position 1)

- Position and hold the section against the stop.- Punch.

Position1

Position2

Position3

IMPORTANT:Lubricatediesandpunchesevery25 cuts with W540.(Ineverycases,lubricateeachweek,iftoolisnotuse).

13.1

Tool instructions

Perfopack 2788for cutting notches on uprights/capping section and connecting section


95 JX

B - CUTTING OF 6 x 3 NOTCHES ON CAPPING SECTION 7772AND CONNECTING SECTION 7711 (position 2)

top of section

bottom of section

3

31.8

=

=

667772

7711


3

31.8 ==

66

7787

B - CUTTING OF 6 x 3 NOTCHES ON CONNECTING SECTION 7787 (position 3)


top of section

bottom of section


96

Numerical Index

1112 Stainlessclip 42

1197 Reversible manoeuvre set 42

1249 Left maneuver with lever 42

1268 Right maneuver with lever 42

1370 Fly screen spline 42

1403 Corner cleat (fly screen) 42

1809 M5 x 30 sleeve (90-head milled) 42

1835 Driving head screw 4 x 25 42

1836 Driving head screw 5 x 25 42

2762 Perfopack for upright 44

2763 Perfopack for upright 44

2764 Perfopack for handle 44

2765 Perfopack for capping section 44

2766 Punch/die for handle 44



2769 Perfopack for alu/glass louvers 44

2773 Perfopack for corner cleat 1403 44

2779 Perfopack for secondary glazing section 7620 44

2786 Autonomoustoolfortransoms/fixedfr.,

archi. and o. s 44

2788 Perfopack for cutting notches 44

3160 Deflector 42

3178 Weatheringdeflector 42

7620 Secondaryglazingsection 5.80m 40

7621 Rebate section 5.80 m 40

7622 Corner cleat set 42

7623 Lock for 7620 42

7624 5/6 mm glazing gasket 42

7625 8/8.8 mm glazing gasket 42

7626 Hinge 42

7627 Rebate gasket 42

7654 6 mm glass louver gasket 42

7657 Positional rail section 5.80 m 40

7661 Fly screen section 5.80 m 40

7662 Securityaluminiumrod(diam=6mm) 3.00m 40

7670 5 mm gasket for glass louver 42

7673 Glass louver gasket (5.5 mm) 42

7677 Subframemullionsection 5.80m 40

7701 Training body 42

7702 Trainer body 42

7703 Trainer body 42

7705 Trainer bearing 42

7709 Sillsection 5.80m 38

7710 Sillsection 5.80m 38

7711 Joining section 5.80 m 39

7713 135 mm aluminium louver 5.80 m 39

7716 Aluminium louver gasket (7713) 43

7717 Bottom part plug 43

7718 Axis 43

7719 Springset 43

7723 Rodset-L:1.38m 43

7724 Louverwindowrod-L:5.38m 43

7759 Uppertransomgasket 43

7765 Louver gasket 43

7772 Capping section 5.80 m 39

7774 Inside sill section 5.80 m 38

7775 Gasket plug 1.00 m 43

7777 Plug 43

7778 6.6 mm glazing louver gasket 43

7787 Junction section 5.80 m 40

7790 Glass louver bearer 5.80 m 39

7791 Transom 5.80 m 38

7792 Transom (lower part) 5.80 m 38

7793 Uprightsection(42mm) 5.80m 39

7795 Uprightsection(50mm) 5.80m 39

7796 Uppertransomarchitrave 5.80m 38

7797 Bottom transom architrave 5.80 m 38

7798 Transom for junction 5.80 m 40

8329 Clip on sill (155 mm) 6.00 m 41

8334 Clip on sill (71 mm) 6.00 m 41

8395 Clip on sill (115 mm) 6.00 m 41

8400 Architrave 6.00 m 41

8402 Architrave (50 mm) 6.00 m 41

8404 Architrave (75 mm) 6.00 m 41

8475 55 mm flashing section 6.00 m 41

8537 FX 109 mm sill 6.00 m 41

8615 Clip-on cover section (60 mm) 6.00 m 41

8617 Clip-on cover section (85 mm) 6.00 m 41

CV056 Turn handle 43

CV057 Insert for transom fixation 43

CV058 Insert (VT) for CV056 handle 43

FE016 Architrave (39 mm) 6.00 m 41

FP043 Rebate section 6.00 m 40

FV085 42 mm pre-drilled upright profile 5.70 m 43

FV086 50 mm pre-drilled upright profile 5.72 m 43

JV003 Uprightgasket 43

KV045 Set(VT)forCV056handle 43

KV046 Nut set for lever handle 1268 43

VE037 Selfdrillingscrew 43

VE046 ScrewTF90M5x70 43

VE047 ScrewTF90M5x90 43

VE048 Screw4.8x55-50 43

W110 Smalljointsealant 43

W118 Siliconcartridge 43

W200 Cyanoacrylateglueforgaskets 43

Ref. Description Height Page Ref. Description Height Page

Note - Note -Note - Note - Note - Note - Note - Note - Note - Note - Note - Note - Note - Note - Note - Note - Note

Jalousie with adjustable louvers - Jalousie with adjustable louvers - Jalousie with adjustable louvers - Jalousie with adjustable louvers - Jalousie with adjustable louvers - Jalousie with adjustable lou- Note - Note -Note - Note - Note - Note - Note - Note - Note - Note - Note - Note - Note - Note - Note - Note - Note

- 2nd Quarter 2006 - Document n 4541.002All reproduction, translation and adaptation reserved for all countries. The law ofMarch 11 1957prohibits the copy or reproduction, for use other than that limited to private use of the copier.Any reproduction made in whole or in part and in any form without the agreement of the author is illegal and constitutes infringement of copyright sanctioned by clause 425 onwards of the penal code.

celosia de aluminio

Documents