Model: CHT940DO

Owner's Manual

PLEASE READ BEFORE OPERATING THIS EQUIPMENT.

37 INCH STEREOSOUND BAR SYSTEMwith Digital Optical Input and Bluetooth® Wireless Technology

37 INCH STEREOSOUND BAR SYSTEMwith Digital Optical Input and Bluetooth® Wireless Technology

IB Size: 105.5 x 210mm (A5)

2

WARNING:Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCCRules. These limits are designed to provide reasonable protection against harmful interferencein a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures: • Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.

•

•

•

FCC Warnings

FCC NOTICE:To assure continued compliance, follow the attached installation instructions and use only shielded cables when connecting to other devices. Modifications not authorized by the manufacturer may void user’s authority to operate this device.

3

1. Insert the plug from the supplied AC/DC Adapter to the DC In Jack on the top of unit.

2. Insert the small plug from the supplied AC Power Cord to the AC In Jack on the AC/DCAdapter.

1. Placing on the tableWhen placing the Sound Bar on an entertainment center, bookshelf, or any type ofenclosed space, be sure to allow at least 2-3 inches of space around the Sound Bar forventilation. If the Sound Bar is enclosed in a tight space, without ventilation, heatgenerated from the Sound Bar could produce a potential heat hazard.

2. Mounting the Speaker Bar onto a wallWe recommend having this speaker professionally mounted. By using the included wallmounting accessories, the sound bar can be mounted onto a wall.

4

Distance Between Two Brackets

NOTE:If Long period of time will not use the unit, unplug the AC Cord from the walloutlet.The Power ON Indicator on the AC/DC Adapter will not light.

To the DC IN jack on the top of the unit.

To the wall outlet

To the AC In Jack

25.9 inches

3. Insert the AC Plug from the supplied AC/DC Adapter to the wall outlet having AC100-240V~; 50/60Hz.

2.1 Mounting on the wooden wallYou may use

1. Mark the position of the mounting screws on the wall using a pencil.2. Drill the supplied screws directly into the marks that you have made on the wall and

leave approx. 0.3 inch length to hook the sound bar.3. Put the sound bar onto the mounting screws. Make sure they are firm and stable.

2.2 Mounting on the wallYou may use

1. Mark the position of the mounting screws on the wall using a pencil.2. Drill 2 x 7/32 inch diameter holes by a powerful electric drill ( Not Supplied ).3. Insert the supplied plastic inserts into the holes by hammer ( Not Supplied ).4. Secure the supplied screws into the plastic insert and leave approx. 0.3 inch

length to hook the sound bar.5. Put the sound bar onto the mounting screws. Make sure they are firm and stable.

2 pieces screws (Included)

2 pieces plastic inserts(Included)

5

2 pieces screws (Included)

25.9 inches

(1) (2)

25.9 inches

Front View

Top View

1. Display2. Remote Sensor

4. FM ANT ( FM Antenna )

6. AUX IN 1 Jack7. AUX IN 2 Jacks

8. DC IN Jack9. POWER/SOURCE Button10. VOL- ( Volume Down ) Button11. VOL+ ( Volume Up ) Button12.13. /TUN - ( Skip Backward/Tune Down ) Button14. /TUN + ( Skip Forward/Tune Up ) Button

6

213 3 3 3

DC INDC 16V, 3A

AUX IN 1

AUX IN 2

L

R

FM ANT

OPTICAL IN

POWER/SOURCE

TUN TUN

VOL - VOL +

- +

4

5 6 7 8 9 10 11 12 13 14

3. Speakers

( Play/Pause) Button5. OPTICAL IN Jack

1. SOURCE Button2. ( Power On/Off ) Button

6. EQ ( Equalizer ) Button7. VOL ( Volume ) - Button8. BASS - Button

9. TREBLE - Button10. ( Mute ) Button

( Skip Forward ) Button12. MO/ST ( Mono/Stereo ) Button13. VOL ( Volume ) + Button14. BASS + Button15. ( Play/Pause ) Button16. TREBLE + Button

7

4. TUN -/ ( Skip Backward ) Button5. M+ (Memory Up) Button

11. TUN +/

1

2

34

65

7

8

9

10

11

12

13

141516

PRESET

3. PRESET Button

BATTERY INSTALLATION ( REMOTE CONTROL)

BATTERY PRECAUTIONSFollow these precautions when using a battery in this device:

8

1. Use only the size and type of battery specified.2. Be sure to follow the correct polarity when installing the battery as indicated in the

battery compartment, a reserved battery may cause damage to the device.3. Do not mix different types of batteries together ( e.g: Alkaline and Carbon-zinc ) or old

batteries with fresh ones.4. If the batteries in the device are consumed or the device is not to be used for a long

period of time, remove the batteries to prevent damage or injury from possible leakage.

rupture. ( Follow battery manufacturer’s instructions.)6. The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.7. Clean the battery contacts and also those of the device prior to battery installation.8. The remote control supplied with a coin/button cell battery. If the coin button cell battery

is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.Keep new and used battery away from children. If the battery compartment does not closesecurely, stop using the product and keep it away from children.If you think batteries might have been swallowed or placed inside any part of the body,seek immediate medical attention.

5. Do not try to recharge the battery not intended to be recharged; it can overheat and

Fig.1 Fig.2 Fig.3

2. Replace the battery by a new CR2025 button cellwith the polarity “+” facing up as the figure below.

3. Close the battery tray.

NOTES:

fluorescent lamp or any other strong lightshines on the REMOTE SENSOR of the unit,the remote operation may be unstable.

°30 °30

Approx. 16 feet

Remote Sensor

---First time using:Remove and discard the insulation film as the figure on right.---If the battery is consumed, replace it as below:

below and the markings on the rear of the remote control.

●When there is an obstacle between the unitand the transmitter may not operate.

● When direct sunlight, an incandescent lamp,

1. Push and slide out the battery tray as the figure

BT--------------------------------------------------------------- BluetoothFM Frequency------------------------------------------------FM RadioAUX 1-----------------------------------------------------------AUX IN 1AUX 2-----------------------------------------------------------AUX IN 2OPTI-------------------------------------------------------------Optical In

9

GENERAL OPERATIONS

1. Connect the AC/DC Adapter to the unit and wall outlet as the previous procedure.The Power ON Indicator on the AC/DC Adapter will illuminate.

2. Press the POWER/SOURCE Button on the unit or press the Button on the remotecontrol to power on the unit from standby mode.

3. Press the POWER/SOURCE Button on the unit or press SOURCE Button on theremote control repeatedly to switch to desired mode as below:

4. During Playback:~ Press the VOL ( Volume ) + or - Buttons on the unit or remote control to adjust volumelevel as desired.

~ Press the EQ Button on remote control repeatedly to select and set equalizer mode to

~ Press the BASS +/- Buttons on remote control to adjust the sound level of bass.~ Press the TREBLE +/- Buttons on remote control to adjust the sound level of treble.5. When finished listening, press and hold the POWER/SOURCE Button on the unit orpress the Button on remote control to power off ( Standby Mode ) the unit. ThePower ON indicator on the AC/DC Adapter will keep illuminate.

6. If the unit will not be used for long period of time, unplug the AC/DC Adapter from thewall outlet. The Power ON Indicator on it will not light.

JAZZ, POP, CLAS (Classic), ROCK and NORM (Normal).~ Press the ( Mute ) Button on remote control to turn off the sound. Press again to

resume.

FM AntennaThe Antenna wire on the top of the unit is for radio reception. If reception is weak, unwindand extend the wire or relocate the wire to improve the radio reception.

10

LISTEN TO FM RADIO

1. Connect the Sound Bar to the power as previous procedures.2. Press the POWER/SOURCE Button on unit or press the Button on remote controlto power on the unit.

3. Press the POWER/SOURCE Button on unit or press the SOURCE Button on remotecontrol repeatedly until the FM frequency appears on the display.

4. Press and hold the TUN - / or TUN + / Button on the unit or remote control untilthe FM frequency on the display start running then release the button to search and

7. If the available FM station is stereo, the unit will plays it in stereo mode automatically.If the reception is no good, press the MO/ST Button on remote control to switch toMono mode. Press again to turn back to Stereo mode.

plays the available FM stations forward or backward. Or,5. Press and hold the PRESET Button on the remote control until the FM frequency on the

display start running then release the button. The unit will search and store all theavailable FM stations automatically, then plays the first searched and stored FM station.(Up to 30 stations can be stored). Press the M+ Button on the remote control repeatedly toselect and plays the desired stored channel.

6. Press and release the TUN - / or TUN + / Buttons on unit or remote controlrepeatedly to fine tune.

BluetoothIn first time use or re-pairing to new BT Device, pairing the unit to the external BT Deviceas follows:

1. Power on the unit as previous procedures.

( For details pairing procedures, please refer to the user's manual of your BT Device.)Notes:1. When the external BT Device searched the unit, our model number " CHT940 " will

2. Pairing code "0000" or "1234" may need to enter.

1. Power on the unit and select the playback source to BT as previous procedures.2. Turn on the BT function of the external BT Device.

11

2. Press the POWER/SOURCE Button on unit or press the SOURCE Button on remote

3. Power on the external BT Device and enter to searching mode. Start pairing as the onscreen instructions on the external BT Device. After paired, the "BT" on display will stopblinking.

3. Wait a few seconds until the unit paired to the external BT Device automatically. The“BT” on display will stop blinking.

5. During playback:~ Press the TUN -/ or TUN +/ Buttons to skip the tracks.~ Press the Button on the unit or remote control to pause. Press again to resumenormal playback.

BLUETOOTH PAIRING AND PLAYBACK

control repeatedly until “BT” appears and blinking on display.

appear on the display of external BT Device.

Normal operation after paired:

4. Play the music in the paired BT Device as usual.

1.Connect the Headphone/Earphone; Aux out jack or Line out jack from the externalaudio player (such like MP3 player; Disc-man … etc) to the AUX IN 1 jack on the top of

4. Power on the connected external player and start playback music as usual.

4. Power on the connected external player and start playback the Video/Music as usual.

12

AUX IN 1 : LISTEN TO EXTERNAL AUDIO DEVICES

AUX IN 2 : LISTEN TO TV/DVD/VCR/DVR

Audio Player

To Phone Jack

Top view of the unit

DC INDC 16V, 3A

AUX IN 1

AUX IN 2

L

R

FM ANT

OPTICAL IN

red

white

To Audio Out Jacks

Top view of the unit

DC

IND

C 1

6V

, 3A

AU

X IN

1

AU

X IN

2

LR

FM

AN

T

OP

TIC

AL IN

2. Power on the unit as previous procedures.3. Press the POWER/SOURCE Button on unit or press the SOURCE Button onremote control repeatedly until the “AUX 1” appears on display.

1. Connect the Aux out jacks from the external audio/video player (such like TV, DVDplayer, VCR …etc.) to the AUX IN 2 jacks on the top of unit by the RCA ConnectionCable as the figure below:

2. Power on the unit as previous procedures.3. Press the POWER/SOURCE Button on unit or press the SOURCE Button onremote control repeatedly until “AUX 2” appears on display.

unit by the Audio Connection Cable with 3.5mm plugs as the figure below:

…etc.) to the OPTICAL IN jack on the top of unit by the Optical Connection Cable as thefigure below:

NOTE:

13

CONNECTION THROUGH OPTICAL

Top view of the unit

DC INDC 16V, 3A

AUX IN 1

AUX IN 2

L

R

FM ANT

OPTICAL IN

DVD Player

BassTrebleBalance

Select Move MENU Exit

Sound Mode Standard

Surround OffAVL Off

Audio Language English

Picture Time Setup Lock OffAudioAudio

Digital Output PCMDigital Output PCM

1. Connect the Optical out jack from the external audio/video player (such like TV, DVD

2. Power on the unit as previous procedures.3. Press the POWER/SOURCE Button on unit or press the SOURCE Button onremote control repeatedly until "OPTI" appears on display.

4. Power on the connected external player and start playback the Video/Music as usual.

If there is no audio output (only picture) when your TV or DVD player is connected to theunit, please check the digital audio output settings of the connected TV/DVD, and set it

Optical Cable

to PCM format as the example picture below.

14

TROUBLESHOOTING GUIDE

SYMPTOM POSSIBLE CAUSE POSSIBLE SOULTIONNo power AC/DC adapter not

connectedConnect the power AC/DCadapter to AC wall outlet andunit.

The unit is in Standbymode

Press the POWER/SOURCEButton on the unit or the

to turn on the unit.No sound Volume in minimum

positionRaise volume level bypressing the VOL(Volume) + Button.

The paired/connecteddevice is not in paybackmode

Play music/movie in thepaired/connected device asusual and make sure thevolume level of it is in highlevel.

Input source incorrect Press the POWER/SOURCEButton on the unit or pressSOURCE Button on theremote control repeatedly toset the input sourceto the desired mode.

Sound distortionBass level of theconnected device too high

Reduce the bass level of theconnected device.Press the BASS - Button onthe Sound Bar to reducebass level.

Volume level too high Reduce the volume level bypressing the VOL (Volume ) -Button.Reduce the volume level ofthe paired/connected device.

Remote not working The battery is consumed Replace with new battery.

Poor FM reception Relocate and unwind the FMantenna wire.

Bluetoothreception failure

The external device is toofar from the unit

Put the external BT deviceclose to the unit.

Have not paired Pair the unit with the BTDevice as the procedures onpage 11.

Button on the remote control

Power Source.................................................................................... DC16V 3ARadio Coverage.............................................................................................87.5-108 MHz

Audio Power:Loud Speakers: ........................................................................................10 W ( RMS ) x 2Woofer: .....................................................................................................10 W ( RMS ) x 2Total:..............................................................................................................................40W

Bluetooth Effective Range in Open Area..........................................................Up to 32 feetRemote Effective Range...................................................................................Up to 16 feet

ACCESSORIES1 x AC/DC Adapter ( Input: AC 100-240V~; 50/60Hz; 1.5A Max. Output: DC16V 3 A,

)1 x Remote Control, using CR 2025 button cell ( Included, already installed in remotecontrol )1 x User's Manual

2 x Plastic Inserts ( For Wall Mounting )2 x Metallic Screws ( For Wall Mounting )

15

1 x 3.5mm AUX IN Cable

SPECIFICATIONS AND ACCESSORIES ARE SUBJECT

TO CHANGE WITHOUT NOTICE

Craig warrants this product to be free from manufacturing defects in material andworkmanship under normal use for a period of 90 days from date of purchase. If serviceis required, please return the product to the store where it was purchased for exchange;or, pack the unit in the original packing material with all accessories if applicable, a copyof your sales receipt and a Cashier’s check or Money Order for $15.00 (to cover shippingand handling costs) payable to Craig Electronics Inc. For consumers in Canada, pleasemake sure that the cashier check or money order is redeemable through a U.S. bank.Ship your product freight pre-paid. Your unit will be repaired, replaced or if the unit cannot be repaired or replaced, a refund will be forwarded to you within four weeks of receiptof your unit. Please ship your unit to:

Craig Electronics Inc.1160 NW 163 Drive

Miami, Fl 33169

This warranty is void if the product has been: a) Used in a commercial application or rental. b) Damaged through misuse, negligence, or abuse. c) Modified or repaired by anyone other than an authorized Craig service center. d) Damaged because it is improperly connected to any other equipment.Note: This warranty does not cover: a) Ordinary adjustments as outlined in the Owner’s Manual which can be performed by the customer. b) Damage to equipment not properly connected to the product. c) Any cost incurred in shipping the product for repair. d) Damage to the product not used in the USA.

This warranty is not transferable and only applies to the original purchase. Any implied warranties, including the warranty of merchantability, are limited in duration to the period of this expressed warranty and no warranty whether expressed or implied shall apply to the product thereafter.

Under no circumstance shall Craig be liable for any loss or consequential damage arising out of the use of this product. This warranty gives specific legal rights. However, you may have other rights which may vary from state to state. Some states do not allow limitations on implied warranties or exclusion of consequential damage. Therefore, these restrictions may not apply to you.

To Obtain Service on your Productemail:service@craigelectronics.com

Printed in China CHT940DO_WC_E0CL1_B0US

LIMITED WARRANTY

Size: 148.5(W) x 210(H)mm (A5)