Anchor™ Sequent™

Retaining Wall Panel System6-inch / 8-inch Combination

Multiheight Wall

APPLICATIONSTerrace Gardens • Landscape Retaining Walls • Geosynthetic Reinforced Tall Walls

PRODUCT INFORMATIONAnchor™ Diamond Pro Stone Cut® and Anchor™ Highland Stone® retaining wall systems combined to create panel system.

Anchor™ Diamond Pro Stone Cut® 8-inch Combo Nominal Dimensions:

SM 7" L x 12" W x 8" HM 11" L x 12" W x 8" HLG 18" L x 12" W x 8" H

Wt./Stone SM 34 lbs., M 45 lbs., L 86 lbsStones/Pallet 48Approx. Wt./Pallet 2,608 lbs.Face ft./Pallet 32Product Number 835

For a fresh look, the Anchor™ Sequent™ Retaining Wall Panel System combines two popular Anchor™ products with great aesthetic and functional results.The panels are a quick way to build a multi height wall by combining the Diamond Pro Stone Cut® and Highland Stone® retaining wall systems in a simpleinstallation pattern. These panels break up the horizontal lines of a typical single height product and can be used with geosynthetic reinforcement. For contractors, the Sequent™ Retaining Wall Panel System installation pattern is quick to install on a large scale when you want to create a random,rough-hewn look without sacrificing productivity – ideal for larger projects.

COMPOSITION AND MANUFACTUREHighland Stone® and Diamond Pro Stone Cut® series are made from a “no slump” concrete mix. Made under extreme pressure and high frequency vibrations, they have acompressive strength greater than 3500 psi and a maximum water absorption of 7%.

Anchor™ Highland Stone® 6-inch Combo Nominal Dimensions:

SM 6" L x 12" W x 6" HM 12" L x 12" W x 6" HLG 18" L x 12" W x 6" H

Wt./Stone SM 26.7 lbs., M 55.2 lbs., L 80.2 lbs.Stones/Pallet 60Approx. Wt./Pallet 3,240 lbs.Face ft./Pallet 30Product Number 876

Face ft.: 43% Highland Stone® 6" ,57% Diamond Pro Stone Cut® 8"Panel & Wall Batter: 8.6°

Note: Colors are shown as accurately as possible in brochures & samples,

but due to the nature of the product, regional color differences and variables

in print reproduction, colors may not match exactly.

Anchor™ Sequent™ Retaining Wall Panel System6-inch / 8-inch Combination

BASIC INSTALLATION – SEE ANCHOR™ SEQUENT™ PATTERN ON BACK

1. Stake Out the Wall’s Placement: Excavate for the leveling pad to the linesand grades shown on the approved plans and excavate enough soilbehind the wall for the reinforcement material. The trench for the levelingpad should be a minimum of 24 inches wide and 6 inches deep.

2. Leveling Pad: An aggregate leveling pad is made of a good compactiblebase material of 3/4 inch minus with fines. The pad must extend 6 inches infront and behind the first course of stone and be at least 6 inches deep.Compact the aggregate and make sure it is level.

3. Base Course: Run a string line along the back of the stone to align the wallunits. Use 6 inch height only stones in the lowest course in the elevationof the wall. Remove the rear lip of the stone so that the stone will lie flaton the leveling pad. Place the stones side by side, flush against each other,and in full contact with the leveling pad. Level front to back and side toside. Check the stones for proper alignment.

4. Next Lift Construction: Clean any debris off the top of the stones. Placethe second course of stones, on the base course while maintainingstaggered bond, and push each stone as far as possible to ensure thecorrect setback. Fill all voids between and within concrete wall units withdrainage aggregate. Backfill with 12 inches of drainage aggregatedirectly behind the stone and fill in soil behind the aggregate. Compactthe backfill before the next course is laid. Avoid driving heavy equipmentnear the wall. Hand-operated equipment should be used within 4 feet ofthe wall units, or half of the wall height.

5. Drainage Design: Place the drain tile as low as possible behind the wall sowater drains down and away from the wall into a storm drain, or to an arealower than the wall.

6. Compaction: Shovel the in-fill soil behind the drainage aggregate andcompact the in-fill with a compacting device. Make sure the aggregate islevel with or slightly below the top of the laid course.

7. Reinforcement: Check your wall construction plan for which courses willneed reinforcement grid. Measure and cut the reinforcement grid to thedesign length in the plans. The reinforcement grid has a design strengthdirection, which must be laid perpendicular to the wall. Place the frontedge of the material on the course, as per wall plan, 2 inches from theface of the stone. Apply the next course of stones to secure it in place.Pull the reinforcement taut and pin the back edge in place with stakes.Add drainage aggregate behind the stones, then add the in-fill soil andcompact it. Place the front edge of the reinforcement on top of thestone, making sure it is within 2 inches of the face of the stone. Aminimum of 6 inches of backfill is required prior to operating vehicleson the reinforcement.

8. Finish Grade and Surface Drainage: Protect the wall with a finished gradeat the top and bottom. To ensure proper water drainage away from thewall, grade crest of wall to accommodate positive drainage.

Anchor™ Sequent™ Retaining Wall Panel System6-inch / 8-inch Combination

Typical Cross Section of Sequent™ Installation Pattern

using the Highland Stone® 6-inchand Diamond Pro Stone Cut® 8-inch

Retaining Wall Panel System

See back page for Sequent™ PatternComplete installation & specification details are available by contacting your Pavestone Sales Representative.

Anchor™ Sequent™ Retaining Wall Panel System6-inch / 8-inch Combination

Installation Guidelines

Install the base course using best practices. The wall is built with a series of panels in a repeating installation pattern. Install filter fabric behind wall. Follow these steps to build panels:

6" x 12"

6

6" x 18"

6

6" x 6"

6

D

D

A

N

W

N

n

1

3'-0"

18"

14"

Panel 1 Panel 2

1. Start by using all three units of Highland Stone® product.

2. Next, use all three units of Diamond Pro Stone Cut® product and stack them onthe first three units, staggering the bond. This completes Panel 1.

3. Working along the wall, next use all three units of Diamond Pro Stone Cut® product.

5. Backfill, compact and install grid or structural backfill, if needed.

4. Next use all three units of Highland Stone® product and stack them on thecourse described in step 3, staggering the bond. This completes Panel 2.Repeat panel installations across the base course.

Continue to install panels to complete the wall.

8" x 11"

8" x 18"

8

8" x 7"

8

8" x 11"

8" x 18"

8" x 7"

6" x 12"

8

6" x 18"

8

6" x 6"

8

Highland Stone® units

Diamond Pro Stone Cut® units

6. Start the next set of panels by staggering the first unit 18 inches to the rightor left of lower panels and repeat step 1.

• Atlanta, GA: (770) 306-9691• Austin/San Antonio, TX: (512) 558-7283• Boston, MA: (508) 947-6001• Charlotte, NC: (704) 588-4747• Cincinnati, OH: (513) 474-3783• Colorado Springs, CO: (719) 322-0101• Dallas/Ft. Worth, TX: (817) 481-5802• Denver, CO: (303) 287-3700

• Hagerstown, MD: (240) 420-3780• Houston, TX: (281) 391-7283• Kansas City, MO: (816) 524-9900• Las Vegas, NV: (702) 221-2700• New Orleans, LA: (985) 882-9111• Phoenix, AZ: (602) 257-4588• Sacramento/

Winters, CA: (530) 795-4400www.pavestone.com

ICPI Charter Member

SKU#

CDC

454

10

/11

© 2011 Pavestone Company. All Rights Reserved. and Creating Beautiful Landscapes™

are trademarks of Pavestone Company. The “Anchor Build Something Beautiful” logo, Highland

Stone®, Diamond Pro Stone Cut®, and Sequent™ are trademarks of Anchor Wall Systems, Inc. (AWS).

Highland Stone and Diamond Pro Stone Cut are manufactured under license from AWS.

The Sequent™ panel system combines the Diamond Pro Stone Cut® and Highland Stone® 6 inch multi piece retaining wall systems toachieve the random look of a multi-height wall system.

Estimating Information

1) Determine the square footage of exposed wall.a) Each panel covers 3.5 sq. ft. Divide the square footage of exposed wall by 3.5 to determine the number of panels.b) Each pallet of Diamond Pro Stone Cut® Combo can complete 16 panels. Divide the number of panels by 16 (rounding up) to

determine the number of Diamond Pro Stone Cut® Combo pallets required.c) Each pallet of Highland Stone® 6 inch Combo can complete 20 panels. Divide the number of panels by 20 (rounding up) to determine

the number of Highland Stone® 6 inch Combo pallets required.2) Determine the linear footage of base course, and divide by the appropriate factor below to calculate the amount of material required.

a) Highland Stone® 6 inch Combo = 60 linear feet per pallet.b) 18 inch only blocks: 1.5 linear feet per stone.

3) Add the exposed wall and base course requirements. Don’t forget the caps!

World Wide Pavers

Installation Pattern