ccna2 lab inst 3 1 5 en
TRANSCRIPT
-
8/2/2019 CCNA2 Lab Inst 3 1 5 En
1/18
36 - 833 CCNA 2: Routers and Routing Basics v 3.1 - Lab 3.1.5 Copyright 2003, Cisco Systems, Inc.
Lab 3.1.5 Configuring a Serial Interface Instructor Version 2500
Objective
Configure a serial interface on each of two routers so they can communicate.
Background/Preparation
Any router that meets the interface requirements may be used. Possible routers include 800, 1600,1700, 2500, 2600 routers, or a combination. Refer to the chart at the end of the lab to correctlyidentify the interface identifiers to be used based on the equipment in the lab. The configurationoutput used in this lab is produced from 1721 series routers. Any other router used may produceslightly different output. The following steps are intended to be executed on each router unlessspecifically instructed otherwise.
Start a HyperTerminal session as performed in the Establishing a HyperTerminal session lab.
Note: Go to the erase and reload instructions at the end of this lab. Perform those steps on allrouters in this lab assignment before continuing.
Step 1 Basic Router Configuration
a. Configure the router. Connect the routers as shown in the diagram. This lab requires a null serialcable and two rollover or console cables.
-
8/2/2019 CCNA2 Lab Inst 3 1 5 En
2/18
37 - 833 CCNA 2: Routers and Routing Basics v 3.1 - Lab 3.1.5 Copyright 2003, Cisco Systems, Inc.
Step 2 Configure the name and passwords for Router 1
a. On Router 1, enter the global configuration mode and configure the hostname as shown in thechart.
b. Configure the console, virtual terminal and enable passwords. If there are any problems, refer tothe Lab 3.1.3 Configuring Router Passwords.
Step 3 Configure serial interface Serial 0
From global configuration mode, configure serial interface Serial 0 on Router GAD. Refer to InterfaceSummary.
GAD(config)#interface serial 0
GAD(config-if)#ip address 192.168.15.1 255.255.255.0
GAD(config-if)#clock rate 56000
GAD(config-if)#no shutdown
GAD(config-if)#exit
GAD(config)#exit
Note: Once the interface configuration mode is entered, note the IP address of the interface.Enter the subnet mask. Enter the clock rate only on the DCE side of the device. The commandno shutdown turns on the interface. The command shutdown turns the interface off.
Step 4 Save the running configuration
Save the running configuration to the startup configuration at the privileged EXEC mode:
GAD#copy running-config startup-config
Note: Save the running configuration for the next time that the router is restarted. The router can
be restarted either by a software reload command or a power shutdown. The running
configuration will be lost if the running configuration is not saved. The router uses the startupconfiguration when the router is started.
Step 5 Display information about Serial interface 0 on GAD
a. Enter the command show interface serial 0 on GAD. Refer to interface chart.
GAD#show interface serial 0
This will show the details of interface serial 0.
b. List at least three details discovered by issuing this command.
c. Serial 0 is down. Line protocol is down.
d. Internet address is 192.168.15.1/24.
e. Encapsulation HDLC
f. To what OSI layer is the Encapsulation referring? Data Link
g. If the Serial interface was configured, why did the show interface serial 0 say that the
interface is down? The other end of the serial link has not been configured.
-
8/2/2019 CCNA2 Lab Inst 3 1 5 En
3/18
38 - 833 CCNA 2: Routers and Routing Basics v 3.1 - Lab 3.1.5 Copyright 2003, Cisco Systems, Inc.
Step 6 Configure the name and passwords for Router 2
a. On the Birmingham router, enter the global configuration mode. Configure hostname, console,virtual terminal and enable passwords as shown in the previous chart.
Step 7 Configure serial interface Serial 0
From the global configuration mode, configure serial interface Serial 0 on Router BHM. Refer tointerface chart.
BHM(config)#interface serial 0
BHM(config-if)#ip address 192.168.15.2 255.255.255.0
BHM(config-if)#no shutdown
BHM(config-if)#exit
BHM(config)#exit
Step 8 Save the running configuration
Save the running configuration to the startup configuration at the privileged EXEC mode:
BHM#copy running-config startup-config
Step 9 Display information about Serial interface 0 on BHM
a. Enter the command show interface serial 0 on BHM. Refer to interface chart.
BHM#show interface serial 0
This will show the details of interface serial 0.
b. List at least three details discovered by issuing this command.
c. Serial 0 is up, line protocol is up.
d. Internet address is 192.168.15.2/24.
e. Encapsulation HDLC
f. What is the difference in the Line and Protocol status recorded on GAD earlier? Why?
Both are now listed as up because a carrier signal is detected from the BHM router.
Step 10 Verify that the serial connection is functioning
a. ping the serial interface of the other router.
BHM#ping 192.168.15.1
GAD#ping 192.168.15.2
b. From GAD, ping the BHM router serial interface. Does the ping work? Yes
c. From BHM, ping the GAD router serial interface. Does the pingwork? Yes
d. If the answer is no for either question, troubleshoot the router configurations to find the error.Then ping the interfaces again until the answer to both questions is yes.
Upon completion of the previous steps, logoff by typing exit. Turn the router off. Remove and storethe cables and adapter.
-
8/2/2019 CCNA2 Lab Inst 3 1 5 En
4/18
39 - 833 CCNA 2: Routers and Routing Basics v 3.1 - Lab 3.1.5 Copyright 2003, Cisco Systems, Inc.
Erasing and reloading the router
Enter into the privileged EXEC mode by typing enable.
If prompted for a password, enterclass.If class does not work, ask the instructor for assistance.
Router>enable
At the privileged EXEC mode, enter the command erase startup-config.
Router#erase startup-config
The responding line prompt will be:
Erasing the nvram filesystem will remove all files! Continue?
[confirm]
Press Enterto confirm.
The response should be:
Erase of nvram: complete
Now at the privileged EXEC mode, enter the command reload.
Router#reload
The responding line prompt will be:
System configuration has been modified. Save? [yes/no]:
Type n and then press Enter.
The responding line prompt will be:
Proceed with reload? [confirm]
Press Enterto confirm.
In the first line of the response will be:
Reload requested by console.
After the router has reloaded the line prompt will be:
Would you like to enter the initial configuration dialog? [yes/no]:
Type n and then press Enter.
The responding line prompt will be:
Press RETURN to get started!
Press Enter.
The router is ready for the assigned lab to be performed.
-
8/2/2019 CCNA2 Lab Inst 3 1 5 En
5/18
40 - 833 CCNA 2: Routers and Routing Basics v 3.1 - Lab 3.1.5 Copyright 2003, Cisco Systems, Inc.
Router Interface Summary
RouterModel
EthernetInterface #1
EthernetInterface #2
SerialInterface #1
SerialInterface #2
Interface#5
800 (806) Ethernet 0 (E0) Ethernet 1 (E1)
1600 Ethernet 0 (E0) Ethernet 1 (E1) Serial 0 (S0) Serial 1 (S1)
1700 FastEthernet 0 (FA0) FastEthernet 1 (FA1) Serial 0 (S0) Serial 1 (S1)
2500 Ethernet 0 (E0) Ethernet 1 (E1) Serial 0 (S0) Serial 1 (S1)
2600 FastEthernet 0/0(FA0/0)
FastEthernet 0/1 (FA0/1) Serial 0/0 (S0/0) Serial 0/1(S0/1)
In order to find out exactly how the router is configured, look at the interfaces. This will identify the type of routeras well as how many interfaces the router has. There is no way to effectively list all of the combinations ofconfigurations for each router class. What is provided are the identifiers for the possible combinations of interfacesin the device. This interface chart does not include any other type of interface even though a specific router maycontain one. An example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviationthat can be used in IOS command to represent the interface.
-
8/2/2019 CCNA2 Lab Inst 3 1 5 En
6/18
41 - 833 CCNA 2: Routers and Routing Basics v 3.1 - Lab 3.1.5 Copyright 2003, Cisco Systems, Inc.
GAD#show running-config
Building configuration...
Current configuration : 567 bytes
!
version 12.1
no service single-slot-reload-enable
service timestamps debug uptime
service timestamps log uptimeno service password-encryption
!
hostname GAD
!
enable secret 5 $1$OgQo$B5wDMtkHcHBxhNvHDkFZm.
enable password cisco
!
!
ip subnet-zero
!
interface Ethernet0
no ip address
shutdown
!interface Serial0
ip address 192.168.15.1 255.255.255.0
no fair-queue
clockrate 56000
!
interface Serial1
no ip address
shutdown
!
ip classless
ip http server
!
!line con 0
password cisco
login
line aux 0
line vty 0 4
password cisco
login
!
end
-
8/2/2019 CCNA2 Lab Inst 3 1 5 En
7/18
42 - 833 CCNA 2: Routers and Routing Basics v 3.1 - Lab 3.1.5 Copyright 2003, Cisco Systems, Inc.
GAD#show interfaces Serial 0
Serial0 is up, line protocol is up
Hardware is HD64570
Internet address is 192.168.15.1/24
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input 00:00:04, output 00:00:02, output hang neverLast clearing of "show interface" counters 00:03:32
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
9 packets input, 1208 bytes, 0 no buffer
Received 9 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
14 packets output, 2085 bytes, 0 underruns
0 output errors, 0 collisions, 3 interface resets
0 output buffer failures, 0 output buffers swapped out
4 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
GAD#ping 192.168.15.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.15.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/36 ms
GAD#show interfaces Ethernet 0
Ethernet0 is administratively down, line protocol is downHardware is Lance, address is 00e0.b055.ff85 (bia 00e0.b055.ff85)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:03:18, output 00:03:18, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
11 packets input, 6798 bytes, 0 no bufferReceived 11 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
43 packets output, 9348 bytes, 0 underruns
0 output errors, 0 collisions, 3 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
-
8/2/2019 CCNA2 Lab Inst 3 1 5 En
8/18
43 - 833 CCNA 2: Routers and Routing Basics v 3.1 - Lab 3.1.5 Copyright 2003, Cisco Systems, Inc.
BHM#show running-config
Building configuration...
Current configuration : 582 bytes
!
version 12.1
no service single-slot-reload-enable
service timestamps debug uptime
service timestamps log uptimeno service password-encryption
!
hostname BHM
!
enable secret 5 $1$HelO$lBy9rBJqS1ecUCCpKQ9R..
enable password cisco
!!
ip subnet-zero
!
interface Ethernet0
no ip address
shutdown
!
interface Serial0no ip address
no fair-queue
!
interface Serial1
ip address 192.168.15.2 255.255.255.0
!
interface BRI0
no ip address
shutdown
!
ip classless
ip http server
!line con 0
password cisco
login
line aux 0
line vty 0 4
password cisco
login
!
end
BHM#show interfaces Serial 1
Serial1 is up, line protocol is upHardware is HD64570
Internet address is 192.168.15.2/24
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input 00:00:06, output 00:00:02, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
-
8/2/2019 CCNA2 Lab Inst 3 1 5 En
9/18
44 - 833 CCNA 2: Routers and Routing Basics v 3.1 - Lab 3.1.5 Copyright 2003, Cisco Systems, Inc.
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/2/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
71 packets input, 4855 bytes, 0 no buffer
Received 66 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
90 packets output, 6410 bytes, 0 underruns0 output errors, 0 collisions, 15 interface resets
0 output buffer failures, 0 output buffers swapped out
65 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
BHM#ping 192.168.15.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.15.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/36 ms
BHM#show interfaces Ethernet 0
Ethernet0 is administratively down, line protocol is down
Hardware is Lance, address is 0000.0c3b.a008 (bia 0000.0c3b.a008)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:24:24, output 00:24:22, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifoOutput queue :0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
38 packets input, 12942 bytes, 0 no buffer
Received 38 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
36 packets output, 7800 bytes, 0 underruns
0 output errors, 0 collisions, 3 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
-
8/2/2019 CCNA2 Lab Inst 3 1 5 En
10/18
451 - 833 CCNA 2: Routers and Routing Basics v 3.1 - Lab 3.1.5 Copyright 2003, Cisco Systems, Inc.
Lab 3.1.5 Configuring a Serial Interface Instructor Version 2600
Objective
Configure a serial interface on each of two routers so they can communicate.
Background/Preparation
Any router that meets the interface requirements may be used. Possible routers include 800, 1600,1700, 2500, 2600 routers, or a combination. Refer to the chart at the end of the lab to correctlyidentify the interface identifiers to be used based on the equipment in the lab. The configurationoutput used in this lab is produced from 1721 series routers. Any other router used may produceslightly different output. The following steps are intended to be executed on each router unlessspecifically instructed otherwise.
Start a HyperTerminal session as performed in the Establishing a HyperTerminal session lab.
Note: Go to the erase and reload instructions at the end of this lab. Perform those steps on allrouters in this lab assignment before continuing.
Step 1 Basic Router Configuration
a. Configure the router. Connect the routers as shown in the diagram. This lab requires a null serialcable and two rollover or console cables.
-
8/2/2019 CCNA2 Lab Inst 3 1 5 En
11/18
452 - 833 CCNA 2: Routers and Routing Basics v 3.1 - Lab 3.1.5 Copyright 2003, Cisco Systems, Inc.
Step 2 Configure the name and passwords for Router 1
a. On Router 1, enter the global configuration mode and configure the hostname as shown in thechart.
b. Configure the console, virtual terminal and enable passwords. If there are any problems, refer tothe Lab 3.1.3 Configuring Router Passwords.
Step 3 Configure serial interface Serial 0
From global configuration mode, configure serial interface Serial 0 on Router GAD. Refer to InterfaceSummary.
GAD(config)#interface serial 0/0
GAD(config-if)#ip address 192.168.15.1 255.255.255.0
GAD(config-if)#clock rate 56000
GAD(config-if)#no shutdown
GAD(config-if)#exit
GAD(config)#exit
Note: Once the interface configuration mode is entered, note the IP address of the interface.Enter the subnet mask. Enter the clock rate only on the DCE side of the device. The commandno shutdown turns on the interface. The command shutdown turns the interface off.
Step 4 Save the running configuration
Save the running configuration to the startup configuration at the privileged EXEC mode:
GAD#copy running-config startup-config
Note: Save the running configuration for the next time that the router is restarted. The router can
be restarted either by a software reload command or a power shutdown. The running
configuration will be lost if the running configuration is not saved. The router uses the startupconfiguration when the router is started.
Step 5 Display information about Serial interface 0 on GAD
a. Enter the command show interface serial 0/0 on GAD. Refer to interface chart.
GAD#show interface serial 0/0
This will show the details of interface serial 0.
b. List at least three details discovered by issuing this command.
c. Serial 0 is down. Line protocol is down.
d. Internet address is 192.168.15.1/24.
e. Encapsulation HDLC
f. To what OSI layer is the Encapsulation referring? Data Link
g. If the Serial interface was configured, why did the show interface serial 0/0say that the
interface is down? The other end of the serial link has not been configured.
Step 6 Configure the name and passwords for Router 2
a. On the Birmingham router, enter the global configuration mode. Configure hostname, console,virtual terminal and enable passwords as shown in the previous chart.
-
8/2/2019 CCNA2 Lab Inst 3 1 5 En
12/18
453 - 833 CCNA 2: Routers and Routing Basics v 3.1 - Lab 3.1.5 Copyright 2003, Cisco Systems, Inc.
Step 7 Configure serial interface Serial 0
From the global configuration mode, configure serial interface Serial 0 on Router BHM. Refer tointerface chart.
BHM(config)#interface serial 0/0
BHM(config-if)#ip address 192.168.15.2 255.255.255.0
BHM(config-if)#no shutdown
BHM(config-if)#exit
BHM(config)#exit
Step 8 Save the running configuration
Save the running configuration to the startup configuration at the privileged EXEC mode:
BHM#copy running-config startup-config
Step 9 Display information about Serial interface 0 on BHM
a. Enter the command show interface serial 0/0 on BHM. Refer to interface chart.
BHM#show interface serial 0/0
This will show the details of interface serial 0.
b. List at least three details discovered by issuing this command.
c. Serial 0 is up, line protocol is up.
d. Internet address is 192.168.15.2/24.
e. Encapsulation HDLC
f. What is the difference in the Line and Protocol status recorded on GAD earlier? Why?
Both are now listed as up because a carrier signal is detected from the BHM router,
Step 10 Verify that the serial connection is functioning
a. ping the serial interface of the other router.
BHM#ping 192.168.15.1
GAD#ping 192.168.15.2
b. From GAD, ping the BHM router serial interface. Does the ping work? Yes
c. From BHM, ping the GAD router serial interface. Does the pingwork? Yes
d. If the answer is no for either question, troubleshoot the router configurations to find the error.Then ping the interfaces again until the answer to both questions is yes.
Upon completion of the previous steps, logoff by typing exit. Turn the router off. Remove and storethe cables and adapter.
-
8/2/2019 CCNA2 Lab Inst 3 1 5 En
13/18
454 - 833 CCNA 2: Routers and Routing Basics v 3.1 - Lab 3.1.5 Copyright 2003, Cisco Systems, Inc.
Erasing and reloading the router
Enter into the privileged EXEC mode by typing enable.
If prompted for a password, enterclass.If class does not work, ask the instructor for assistance.
Router>enable
At the privileged EXEC mode, enter the command erase startup-config.
Router#erase startup-config
The responding line prompt will be:
Erasing the nvram filesystem will remove all files! Continue?
[confirm]
Press Enterto confirm.
The response should be:
Erase of nvram: complete
Now at the privileged EXEC mode, enter the command reload.
Router#reload
The responding line prompt will be:
System configuration has been modified. Save? [yes/no]:
Type n and then press Enter.
The responding line prompt will be:
Proceed with reload? [confirm]
Press Enterto confirm.
In the first line of the response will be:
Reload requested by console.
After the router has reloaded the line prompt will be:
Would you like to enter the initial configuration dialog? [yes/no]:
Type n and then press Enter.
The responding line prompt will be:
Press RETURN to get started!
Press Enter.
The router is ready for the assigned lab to be performed.
-
8/2/2019 CCNA2 Lab Inst 3 1 5 En
14/18
455 - 833 CCNA 2: Routers and Routing Basics v 3.1 - Lab 3.1.5 Copyright 2003, Cisco Systems, Inc.
Router Interface Summary
RouterModel
EthernetInterface #1
EthernetInterface #2
SerialInterface #1
SerialInterface #2
Interface#5
800 (806) Ethernet 0 (E0) Ethernet 1 (E1)
1600 Ethernet 0 (E0) Ethernet 1 (E1) Serial 0 (S0) Serial 1 (S1)
1700 FastEthernet 0 (FA0) FastEthernet 1 (FA1) Serial 0 (S0) Serial 1 (S1)
2500 Ethernet 0 (E0) Ethernet 1 (E1) Serial 0 (S0) Serial 1 (S1)
2600 FastEthernet 0/0(FA0/0)
FastEthernet 0/1 (FA0/1) Serial 0/0 (S0/0) Serial 0/1(S0/1)
In order to find out exactly how the router is configured, look at the interfaces. This will identify the type of routeras well as how many interfaces the router has. There is no way to effectively list all of the combinations ofconfigurations for each router class. What is provided are the identifiers for the possible combinations of interfacesin the device. This interface chart does not include any other type of interface even though a specific router maycontain one. An example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviationthat can be used in IOS command to represent the interface.
-
8/2/2019 CCNA2 Lab Inst 3 1 5 En
15/18
456 - 833 CCNA 2: Routers and Routing Basics v 3.1 - Lab 3.1.5 Copyright 2003, Cisco Systems, Inc.
GAD#show running-config
Building configuration...
Current configuration : 661 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption!
hostname GAD
!
enable secret 5 $1$d5a1$W3UB2Z5FI76zkcpgY0nXw1
!
ip subnet-zero
!
call rsvp-sync
!
interface FastEthernet0/0
no ip address
shutdown
duplex auto
speed auto!
interface Serial0/0
ip address 192.168.15.1 255.255.255.0
no fair-queue
clockrate 56000
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface Serial0/1no ip address
!
ip classless
ip http server
!
dial-peer cor custom
!
line con 0
password cisco
login
line aux 0
line vty 0 4
password cisco
login!
end
-
8/2/2019 CCNA2 Lab Inst 3 1 5 En
16/18
457 - 833 CCNA 2: Routers and Routing Basics v 3.1 - Lab 3.1.5 Copyright 2003, Cisco Systems, Inc.
GAD#show interface serial 0/0
Serial0/0 is up, line protocol is up
Hardware is PowerQUICC Serial
Internet address is 192.168.15.1/24
MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input 00:00:02, output 00:00:02, output hang neverLast clearing of "show interface" counters 04:32:31
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 94
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
202 packets input, 15084 bytes, 0 no buffer
Received 187 broadcasts, 0 runts, 0 giants, 0 throttles
2 input errors, 0 CRC, 2 frame, 0 overrun, 0 ignored, 0 abort
219 packets output, 15528 bytes, 0 underruns
0 output errors, 0 collisions, 14 interface resets
0 output buffer failures, 0 output buffers swapped out
61 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
GAD#ping 192.168.15.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.15.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/41/80 ms
GAD#show interfaces fastEthernet 0/0
FastEthernet0/0 is administratively down, line protocol is downHardware is AmdFE, address is 0007.eb38.15e0 (bia 0007.eb38.15e0)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Auto-duplex, Auto Speed, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 04:18:23, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec0 packets input, 0 bytes
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
371 packets output, 192450 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
-
8/2/2019 CCNA2 Lab Inst 3 1 5 En
17/18
458 - 833 CCNA 2: Routers and Routing Basics v 3.1 - Lab 3.1.5 Copyright 2003, Cisco Systems, Inc.
BHM#show running-config
Building configuration...
Current configuration : 618 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption!
hostname BHM
!
enable secret 5 $1$FEj.$QR8mnIciBNgp6fR6aWpKJ.
!
ip subnet-zero
!
call rsvp-sync
!
interface FastEthernet0/0
no ip address
duplex auto
speed auto
!interface Serial0/1
no ip address
no fair-queue
!
interface FastEthernet0/1
no ip address
duplex auto
speed auto
!
interface Serial0/0
ip address 192.168.15.2 255.255.255.0
!
ip classlessip http server
!
dial-peer cor custom
!
line con 0
password cisco
login
line aux 0
line vty 0 4
password cisco
login
!
end
BHM#show interfaces serial 0/0
Serial0/1 is up, line protocol is up
Hardware is PowerQUICC Serial
Internet address is 192.168.15.2/24
MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
-
8/2/2019 CCNA2 Lab Inst 3 1 5 En
18/18
459 833 CCNA 2: Routers and Routing Basics v 3 1 Lab 3 1 5 Copyright 2003 Cisco Systems Inc
Last input 00:00:01, output 00:00:04, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/2/32 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 96 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec5 minute output rate 0 bits/sec, 0 packets/sec
29975 packets input, 1792837 bytes, 0 no buffer
Received 29954 broadcasts, 0 runts, 0 giants, 0 throttles
1 input errors, 0 CRC, 1 frame, 0 overrun, 0 ignored, 0 abort
30081 packets output, 1797876 bytes, 0 underruns
0 output errors, 0 collisions, 567 interface resets
0 output buffer failures, 0 output buffers swapped out
126 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
BHM#ping 192.168.15.1
Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 192.168.15.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/32/36 ms
BHM#show interfaces fastEthernet 0/0
FastEthernet0/0 is up, line protocol is up
Hardware is AmdFE, address is 0005.3201.94c0 (bia 0005.3201.94c0)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)Full-duplex, 100Mb/s, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:22, output 00:00:06, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
2043 packets input, 835659 bytes
Received 2043 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected29047 packets output, 2143110 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out