ccie lab center

CLC - CCIE Service Provider v5.0: Real Lab v1.0 CLC

Forum- https://cciestudygroup.org Website- https://ccielabcenter.com CCIE EI- Real Lab 1.0

CCIE Lab Center

Module 2: Demo Lab CLC CCIE Service Provider Real Lab v1.0 Released: 25-August-2021

Web: https://ccielabcenter.com | Mail: [email protected] | Telegram: t.me/cciestudygroup Page 1



Workbook Description

Author: CCIE Lab Center (CLC) Focus: Real Level: Expert (CCIE) Stream: CCIE Service Provider Lab Version: Lab 1.0 Document Revision: Demo Lab Document Revision Date: 25-August-2021 Content: Topology, Question, Solution, Format: PDF Protection: N/A Website: https://ccielabcenter.com

https://ccielabcenter.com/



Table of Contents

0. Lab Details

Lab Topology

1. Section 1: Core Routing (25%)

1.1 IS-IS

2. Section 2: Architectures and Services (25%)

3. Section 3: Access Connectivity (10%)

4. Section 4: High Availability and Fast Convergence (10%) 5. Section 5: Security (10%) 6. Section 6: Assurance and Automation (20%)



CLC CCIE Service Provider Real Lab 1.0: Diagram 1.1# Main

Topology

SECTION 0: Lab Details

SECTION 0.1: Lab Topoloy



CLC CCIE Service Provider Real Lab 1.0: Diagram 1.2# Eve-ng

Topology



CLC CCIE Service Provider Real Lab 1.0: Diagram 2# AS100 & Green-Site Connectivity



CLC CCIE Service Provider Real Lab 1.0: Diagram 3# AS100 & Green-Site IP Address



Welcome back to the FABD2 company!

You will now deploy, operate and optimize our network.

The Emerald Tier 1 Service Provider operates in different geographical locations. Enable IS-IS in this network across three instances (AGG1, CORE, AGG2) as per given requirements

All three instances must be in Layer 2.

Derive the NET-ID where the last three octets of the device loopback0 address should match the system DI of the node. For example loopback0 address of 10.255.0.1 should have net ID of 49.0001.0010.0255.0000.0001.00

Only use flexible CLI configuration groups called CCIE-ISIS to simplify the configuration. Use AGG1, CORE and AGG2 IS-IS instances for both IPv4 and IPv6 respectively.

Use the same IS-IS database for IPv4 and IPv6

Make sure to allow IS-IS to be able to use metric values higher than 63. Use a Layer 2 metric of 200 for IPv4 and 400 for IPv6.

Make sure IS-IS adjacency formation/maintenance is optimized from the bandwidth utilization point of view using flexible CLI configuration groups.

Make sure not to leak IGP routes between the three IS-IS instances.

Interfaces connected between nodes need to be P2P.

Make sure both Route Reflectors (RR) are reachable from the IS-IS CORE instance.

Make sure LDP is enabled in each IS-IS instance. On X-RR1 X-RR1(config-if)#ip router isis CORE X-RR1(config-if)#Ipv6 router isis CORE X-RR1(config-if)#Isis network point-to-point X-RR1(config-if)#No isis hello padding X-RR1(config-if)#exit X-RR1(config)#

Section 1: Core Routing (25%)

SECTION 1.1: IS-IS

Solution

QUESTION



X-RR1(config)#Router isis CORE X-RR1(config-router)#Net 49.0001.0001.0000.0100.0009.00 X-RR1(config-router)#Is-type level-2-only X-RR1(config-router)#Metric-style wide X-RR1(config-router)#Passive-interface Loopback0 X-RR1(config-router)#exit X-RR1(config)# On X-RR2 X-RR2(config-if)#ip router isis CORE X-RR2(config-if)#Ipv6 router isis CORE X-RR2(config-if)#Isis network point-to-point X-RR2(config-if)#No isis hello padding X-RR2(config-if)#exit X-RR2(config)# X-RR2(config)#Router isis CORE X-RR2(config-router)#Net 49.0001.0001.0000.0100.0010.00 X-RR2(config-router)#Is-type level-2-only X-RR2(config-router)#Metric-style wide X-RR2(config-router)#Passive-interface Loopback0 X-RR2(config-router)#exit X-RR2(config)# Further Solution Omitted For full Lab Solution https://ccielabcenter.com/product-category/service-provider/

CLC CCIE Service Provider Lab v1.0 Demo *****************The End*****************

ccie lab center

Documents