catalogue 2020 - equipment africa...truck tyre changer t568 • semi- automatic truck tyre changer...
TRANSCRIPT
Unit 19 Kemps Business Park16 Vuurslag Avenue, Sebenza, Kempton Park, 1619
Tel: +27 11 392 6109Fax: +27 86 536 5121Cell: +27 82 413 2629
CATALOGUE 2020
www.equipmentafrica.co.za
Page 1
Equipment Africa is offeringTOP OF THE RANGE Wheel Alignment training, on
site, to your technicians.
Training will include,Basic Wheel Alignment and advanced
Wheel Alignment,including BENDING, SHIMMING, SLOTTING etc.
If you are interested with us providing this serviceplease contact us on below:
TEL: 011 392 6109 OR 082 413 2629EMAIL: [email protected]
www.equipmentafrica.net
Page 2
M&B 803D
WHEEL ALIGNMENT AUTOMATIC VEHICLE HEIGHT TRACKING WITH HD CAMERAThe camera system follows the heightof the vehicle, eliminating the need toadjust the aligner when you move thelift, and has very good accuracy than5-megapixel camera. Get readings inless than two minutes on a widevariety of vehicles and wheel sizes.Comprehensive vehicle specificationdatabase with frequent updatesensures you always have theinformation to do the job right.
FeaturesCE certification, Patents, Intellectual PropertyRights of software, HD Camera, Small Target, USBInterface, FPGA Technology, TemperatureCompensation, Intuitive , 3D dynamic simulation,Real-time Measuring, Less demand to lift level, highprecision and quality, Need not WheelCompensation.* Combined with 4 small target, 2 HD cameras 3Dsystem provides the most economic and accuratefour-wheel alignment.* Camera constantly takes pictures from the fourtarget plates and do precise calculation, themeasurement data immediately shown.* Camera calibration has been done in the factory.* The camera is fixed on the beam and no need toadjust.* The target does not have electronic devices, wireand battery, no need to calibrate
M&B 802DWHEEL ALIGNER WITH HD CAMERA
The 802D model Imaging WheelAlignment System is one of the mostadvanced alignment systems on themarket today. It has very goodaccuracy than 5-megapixel camera, CEcertification, Patents, IntellectualProperty Rights technology providesaccurate and real-time measurementsthat improve productivity. Userfriendly features, such as instalmentfunction, Two wheel positioningMode, and an extensive vehiclespecification database deliverscustomer satisfaction, ease of use andaccuracy.
FeaturesHD Camera, USB Interface, FPGA Technology,Temperature Compensation, Intuitive , 3D dynamicsimulation, Real-time Measuring, Less demand tolift level, Durable Small Target plates, highprecision and quality, Need not WheelCompensation.* Combined with four small targets, 2 high-definition cameras 3D system provides the mosteconomic and accurate four-wheel alignment.* Camera constantly takes pictures from the fourtarget plates and do precise calculation, themeasurement data immediately shown.* Camera calibration has been done in the factory.* The camera is fixed on the beam and no need toadjust.* The target does not have electronic devices, wireand battery, no need to calibrate
M&B 801DWHEEL ALIGNER WITH HD CAMERA
The 801D model Imaging WheelAlignment System is one of themost advanced alignment systemson the market today. It has verygood accuracy than 5-megapixelcamera, CE certification, Patents,Intellectual Property Rightstechnology provides accurate andreal-time measurements thatimprove productivity. User friendlyfeatures, such as instalmentfunction, Two wheel positioningMode, and an extensive vehiclespecification database deliverscustomer satisfaction, ease of useand accuracy.
Power, 500 W,110V~220V AC,50/60HzBeam with 2HD Cameras,Moveable cabinet Computer,Brand PC,Software requirement: Win 7,32-bit system.Internal Memory Capacity, 1G. Hard disk, 250GB.CPU speed, 2.9GHz,Dongle:1PC,Monitor,19".Printer, A4 printer.Target : 4 small targets.Clamp, 12"-22",24" optionBrake Fixer.Lock for Steering wheel.Turntables, 2PCS2PCS Wedge Block .
Page 3
www.equipmentafrica.net
Page 4
www.equipmentafrica.net
Haweka –
Truck wheel aligner – Laser type
Laser-sharp – Laser-fastThe greatest advantage of the system is speed. There is no other wheel alignmentmachine today that allows the operator to measure a 2-axle semi-trailer tractorwithin about 10 minutes flat!*. Haweka TA-20 is able to this thanks to its patentedlaser measuring head. The measuring head is placed on the rim by means ofpowerful magnetic feet (with additional grab arms for aluminium rims) and themeasurement can begin immediately. Since the measuring does not need to becompensated like all other machines, there is no need for the time consuming taskof lifting up the vehicle for run-out compensation. The system allows for themeasurement of front toe, individual toe, camber toe out on turns, turning radius,castor, kingpin inclination angle, angular tilt of axles thrust angle and axle offset.
Portable and FlexibleThe precise measurement gauges are stored in a heavy-duty wooden trunk that ensures, even inmobile use, the investment is totally protected. No electricity supply is required, as the batteries inthe laser heads have a minimum of eight hours continual use, and the battery in the electronicprotractor lasts over 2000 hours. The system is completely portable and can be sued on a level ornon-level site. Most traditional wheel alignment machines need a level floor, but the Haweka TA-20 system compensates for any unevenness in the floor. (an industry first).
www.equipmentafrica.net
M & B WB690 Truck / Car Wheel Balancer
Max Wheel Diameter 1150mmWheel Width 20”Max Wheel Weight 200kgAccuracy 1gRotation Speed 100/200rpmPower 0.55kw Machineweight 250 kgEquipped with a Wheel Lift
Camera Radio System AXIS4000The Wheel Alignement System AXIS4000 is a new and innovativedevelopment from HAWEKA. This top-of-line product is the resultof many years of experience in mobile wheel years of experience inmobile wheel alignment. This high-quality wheel alignment system enables a fast, precise andstate-of-the-art measurment. The decisive factor that led to thefurther development of this measuring procedure has been theworldwide high requirment for wheel alignment together with theflexibility and accuracy of the measurement technology. The result isa measurement system that matches the standards of car wheelalignment inasmuch as easy handling and measurment accuracy areconcerned. All this is offered at an unbeatable price.
M & B WB 190 Truck / Car Wheel BalancerMax Wheel Diameter 1300mmWheel Width 20 ”Max Wheel Weight 250kgAccuracy 1gRotation Speed 70/130rpmPower 12v batteryweight 125 kgShaft height adjustable by handle.Even suitable for the heaviest andbiggest Super Single wheels.No lift needed.
Page 5
Truck Wheel Balancer GEO988
• Kepad control panel with bright LED displays indicate 2 weight amounts 2 weight locations, 3D rimdiamension data entry and 3 selection balance mode.
• Precise wheel clamping system flange, easy and fast to fix the wheel on the measuring• Balancer axle. Safety set with microswitch the wheel cover is on position then the wheel begins to rotate. Max. Wheel weight 200kg
Rim Diameter 16” – 24”Rim Width 5,7” – 20”Max. Tyre Diameter 1250mm
Air Pressure 8-10barTesting Time 12-20sPower 220/400v
www.equipmentafrica.net
DIDO 26MV + WB 290
New digital hand-spin wheel balancerdesigned for the mobile service. Itensures the perfect dynamic balancingof all truck, bus, van and car wheelsthanks to the application of the 2weights. Fitted on the tyre changer side(2 in 1 system, patented by M&B), itprovides a complete wheel service withreduced space requirement and weight.The WB290 is equipped with theautomatic internal data arm for a rapidintroduction of the rim’s diameter andthe distance. The width is introducedmanually.
Page 6
www.equipmentafrica.net
Truck Tyre Changer T568 • Semi- Automatic truck tyre changer T568 Unviersal Self-centering chuckrim capacity 14” – 26”
• Clockwise and anticlockwise rotation of chuck
• Italian pump optionalMax. Wheel weight 500kgRim Diameter 14” – 26”Max. Tyre Diameter 1600mmHydraulic Pump motor 1.5kwGearbox motor 1.8kwBead breaker force 2500kgOperation control voltage 24vMachine weight approx. 570kgOverall dimensions approx 2500x2000mmPower 220/400v
Truck Tyre Changer T988A
Max. Wheel weight 2000kgRim Diameter 14” – 48”Rim Capacity 14” – 60”Max. Tyre Diameter 2600mmMax. wheel width 1400mmHydraulic Pump motor 2.4 / 3.0kwGearbox motor 2.4 / 3.0kwPower 400v
Dido 30Max Wheel Diameter 1640mmWheel Width 34”Max Wheel Weight 1200kgRotation Speed 7rpmPower 1.5kw Machineweight 605 kgMax Rim Diameter 30”
Dido 56
Max Wheel Diameter 2300mmWheel Width 54”Power Requirements 2,2 - 3kwRotation Speed 4,5 – 9 rpmMachine weight 855 kgMax Rim Diameter 56”
Page 7
Dido 60
Max Wheel Diameter 2700mmWheel Width 1500mmPower Requirements 2,2 - 3kwRotation Speed 4,5 – 9 rpmMachine weight 1550 kgMax Rim Diameter 60”
Max Wheel Diameter 30”Wheel Width 20”Max Wheel Weight 80kgAccuracy 1gRotation Speed 200rpmMotor0.25kW Power Requirements220v/1ph Machine weight148 kg
M&B Volantino WB200
www.equipmentafrica.net
Max Wheel Diameter 1120mmMax Wheel Width 20”Max Wheel Weight 70kgAccuracy 1gRotation Speed 200rpmMotor 0.25kWPower Requirements 220v/1phMachine weight 90 kg
Manual data input
M & B 277 Wheel Balancer
Can be defined as a wheelbalancing diagnostics centre. Acomputerized electronic wheelbalancer with LCD X VGAmonitor, which includes all thefunctions and characteristics ofthe WB640 model. It has a largerworking surface to fully satisfy allthe operator’s requirements andto hold the SENSOR –SPLIT device
Max Wheel Dia 1120mmMax Wheel Width20” Max Rim Dia30” Max Wheel Weight70kg Accuracy1g Rotation Speed200rpm Machine weight90 kg
M & B 670 Wheel BalancerM & B 680 Wheel Balancer
WB680P
Technical DataMax Rim width 2” – 20”Max Rim diameter 8” – 30”Max Tyre diameter 1120mm-44”Max Tyre width 20”Max Tyre weight 70kg
Machine weight 65kg
Motor 0kwPower requirements 230/1/50-60
Page 8
www.equipmentafrica.net
ZH825L
Passenger Wheel Balancers
PRODUCT FEATURES•With LED display for car and light-truck wheels•Aluminium gauge head with wheel weight clamp•Automatic distance and wheel diameter measuring•Automatic width measuring by width gauge•DYN mode for standard rim, 6 ALU modes for alloy rimsor special shaped rim, statistic mode for motorcycle rim
•Pluggable position pick up board•SP and hidden weight mode•OPT mode for optimization•Self-diagnoses, easy to find the problem•Pedal-operated main shaft lock
TECHNICIAL PARAMETERMax. wheel weight: 65kgMotor power: 0.2kw/0.37kwPower supply: 220v/110vBalancing accuracy: 1gBalancing speed: 200r.p.m.Rim diameter: 10"~24"Rim width: 1.5"~20"
ZH825A
PRODUCT FEATURES•Aluminium gauge head with wheel weight clamp•Automatic distance and wheel diameter measuring•DYN mode for standard rim, 3 ALU modes for alloyrims or special shaped rim, statistic mode for motorcyclerim•Pluggable position pick up board•SP and hidden weight mode•OPT mode for optimization•Self-diagnoses, easy to find the problem•Pedal-operated main shaft lock
TECHNICAL PARAMETERMax. wheel weight: 65kgMotor power: 0.2kw/0.37kwPower supply: 220v/110vBalancing accuracy: 1gBalancing speed: 200r.p.m.Rim diameter: 10"~24"Rim width: 1.5"~20"
Page 9
ZH855L
PRODUCT FEATURES•With LED display for car and light-truck wheels•Aluminium gauge head with wheel weight clamp•Automatic distance and wheel diameter measuring•Automatic width measuring by width gauge•DYN mode for standard rim, 6 ALU modes for alloy rimsor special shaped rim, statistic mode for motorcycle rim
•Pluggable position pick up board•SP and hidden weight mode•OPT mode for optimization•Self-diagnoses, easy to find the problem•Pedal-operated main shaft lock
TECHNICIAL PARAMETERMax. wheel weight: 65kgMotor power: 0.2kw/0.37kwPower supply: 220v/110vBalancing accuracy: 1gBalancing speed: 200r.p.m.Rim diameter: 10"~24"Rim width: 1.5"~20"
•Laser guided weight position indicator
www.equipmentafrica.net
Technical Data
Motorcycle tire size 5”-22”Car tire size 9”-20”Weight 34.5KG
SD18 Tyre Changer - Manual
This portable tyre changer is equipped withprofessional accessories, can be operated easilywithout power and pneumatic supplies. It can workfor different kinds of vehicle tyres, such as MXT,ATV, scooter, and electro mobiles. It is perfect forfamily garage, racing team, long driving journey,emergencies, and different kinds of automobilegarages.
Max Wheel Diameter 960mmRim Width 3” – 10”Outside Clamping 6” – 24”Rotation Speed 7 rpmPower 0.75 -1.1kwMachine weight 175 kg
Specially designed tyre changer for two and four wheelmotorcycle tyres. Special Tool head designed specificallyfor easy mounting & dismounting of motorcycle tyres of allsizes. The shape of the bead breaker blade will easilybreak the bead of small , narrow and standard motorcycletyres. The sliding clamping jaws have three positions thatwill cover from 6” to 24” rims.
M806 Motorcycle Tyre Changer
Page 10
ZH620 - TYRE CHANGERMax Wheel Diameter: 960mmMax Wheel Width: 280mmOutside Clamping: 10” – 18“Inside Clamping: 12” – 21”Air Supply: 8 – 10 BarBead Breaker Force: 2500KGNoise Level: <70dbWeight: 229KG
ZH650R - FULL AUTOMATIC TYRE CHANGERMax Wheel Diameter: 1120mmMax Wheel Width: 360mmOutside Clamping: 10” – 21“Inside Clamping: 12” – 24”Air Supply: 8 – 10 BarBead Breaker Force: 2500KGNoise Level: <70dbWeight: 384KG
www.equipmentafrica.net
M & B 528LL
M & B 528
M & B 525
Leverless Tyre Changer
Page 11
IM- BBR Bead Knocker / Stamper
www.equipmentafrica.net
Power Requirement 110/240Vac / 50 -60Hz,Power Consumption 10VA, OperatingTemperature Range -20º to 70º C, MaxInlet Air Supply 116PSI/8bar/800kPaOperating Range 5-102PSI/0.3-7bar/35-700kPa, Over Pressure Setting Range 0-2bar/0-200kPa, Accuracy - 0.07bar/7kPa,Resolution 1PSI/0.1bar/5kPa, Units ofMeasurement PSI/bar/kPa, Dimensions (L*W*H) 230 x 120 x 290mm , PackingSize(L*W* H) 500 x 290 x 170mm , NetWeight 4kg, Gross Weight 6.5kg
Feature:Adjustable Over Pressure Setting (OPS),Auto-start inflation, Automatic zero driftadjustment., Remain at last setting,Comprehensive diagnostics and errorreporting, Audible and visual end of the cyclesignal indicators. Large backlight LCD display1 x 10m/32.8ft standard hose with singleclip-on open type chuck,
PA101Same as PA101 but can inflate 4 tyres ata time
PA108
Set consists of:1 x Demounting Tool, 1 x Mounting Tool, 1 x Bead KeeperMount and de-mount all tubeless tires 17.5'' to 24.5''.Demount tyre in 8 seconds, Re-mount in 20 seconds withoutstrain - Two simple tools do it all. Works on all standardtubeless and super single duplex tyres. The Changing Tools donot damage beads. Mounts and demount tyres without theneed to lift the tyre. The bead keeper prevent the bead fromskipping when mounting the top bead. Metal constructioncoated with PVC will not scratch aluminium wheels
IM- Tubeless Tyre Changing Tool Set
Demounting Tool
Mounting Tool
Bead Keeper
Preset Tyre Inflators
Input pressure: 8 bar /120psiOperating pressure: 6 - 8 bar / 87-116psi
Max. pressure: 10 bar / 145Psi
Rapid tyre inflation, after tyre fitting. Equipped with automatic purge ofover limit pressure., Supplied with Pressure Gauge
IM-BB-05IM-BB-10
Weight: 11kgDimension: 400x450x360mm
Weight: 15kgDimension: 600x480x360mm
IM- BB Bead Blaster
Universal Bead Breaker for 3 piece rims
Y471120 – Works on mostsingle, two and three piecerims
Y471130 – To be used on 5 piece rims 25” – 51”. With prybar / bead loosening pockets. G.W.14
OTR Bead Breaker for 5 piece rims
Page 12
www.equipmentafrica.net
Zell AC1000-3G Air-Con Service Station
AC1000-3G Specification & ConfigurationRefrigerant R134aOperating Temperature 5 – 50 o CMax pressure 18 barPower Supply 220v, 50HzWeight 95kgPacking Size 50 x 70 x 107cmHP/LP Gauge 80mm/class 1.0Tank Gauge 40mmLCD back lit 192 x 64 dotHP/LP hoses 250cm / SAE-JS2196Compressor 3/8hp, 14ccFan/ condenser YesFilter Drier 80kgVacuum Pump 120L/min, 4.2cfmPAG bottle 250mlElectronic Scale 1g / 30kg
R134a refrigerant
Zell AC1000-HFO Air-Con Service StationHFO - R1234yf refrigerant
AC1000-HFO Specification & ConfigurationRefrigerant HFO-R1234yfOperating Temperature 5 – 50 o CMax pressure 18 barPower Supply 220v, 50HzWeight 95kgPacking Size 50 x 70 x 107cmHP/LP Gauge 80mm/class 1.0Tank Gauge 40mmLCD back lit 192 x 64 dotHP/LP hoses 250cm / SAE-JS219Compressor 3/8hp, 14ccFan/ condenser YesFilter Drier 80kgVacuum Pump 120L/min, 4.2cfmTank 14.5PAG bottle 250mlElectronic Scale 1g / 30kg
IM-C/Jack- Auxiliary jack with hand pump
IM-6006- Auxiliary jack & cradle support3 ton capacity - Air operated
IM-6006- Auxiliary jack & cradle3 ton capacity - Air operated
IM-RJ 6 AuxiliaryRolling Jack
Page 13
www.equipmentafrica.net
These professional bottle jacks meet the highest standards. All models have a chrome main ram and chrome pump piston. The e xtensionscrews have a pressed tread. These units can be used horizontally and vertically.
Model Capacity MinHeight
LiftingHeight
Adj.Height
MaxHeight
N.W
Y410200 2 Ton 158 90 60 308 2.3
Y410400 4 Ton 180 110 60 350 3.3
Y410600 6 Ton 197 125 60 382 4.4
Y411200 12 Ton 214 125 60 399 7.2
Y412000 20 Ton 244 145 60 449 10.5
Y413000 30 Ton 285 180 0 465 14.6
Hydraulic Bottle Jacks
Professional diagnostic device based on Internet application
Page 14
X‐431 PRO is a new type of auto diagnostic devicedeveloped by LAUNCH based on Android systemand Internet application. It inherits LAUNCHcompany's product features of vast cover of carmodules, strong diagnostic functions, many specialfunctions, and precise test data Through Bluetoothcommunication between diagnostic connector andsmart terminal device to realize all car modules andfull system auto malfunction diagnosis. X‐431 PROhas the application advantage of mobile Internet,which could sharing the Maintenance and casesdatabase of the DBScarnetwork., also provideinstant maintenance information, create publicand private circle and so on. So as to enter a vastauto diagnostic community. This is an internetapplication based classic diagnostic deviceprovided by Launch to diagnostic industry.
1. tablet with high configuration2. multi-point capacitive touchscreen3. Bluetooth diagnosis4. online service5,light and small6. multitask on one screen7. support WIFI8. open Androidplatform9 .many additional functions.
Diagnostic Machine
Select car module and test function
click
selection interface
“Engine system”, after initializationcompletes, the screen displays the function
Click “Read DTCs” screendisplays diagnose result, that can be savedas words or image format. Click red buttonreturn to the function selection interface
select car module after logged in
www.equipmentafrica.net
Model name AM-983DriveSpeed150rpmElectrical specifications220v/50HzMaximum diameter of brake disc500mmThickness of brake disc 6-40mmCutting depth per knob 0.005-0.015mm
Model name AM-8700Drive Speed89rpmElectrical specifications220v/50HzMaximum diameter of brake disc400mmThickness of brake disc 6-40mmCutting depth per knob 0.005-0.015mm
Capacity- 1TonMax. working length: 450mmRam travel: 420mmSpring size: 4~6-1/2 inchAir pressure: 0.65-0.9MPaN.W.: 63kgsG.W.: 67kgsPackage Size- 140.5x54.5x29cm
IM- SD1206 Coil Spring Compressor
•Maximum bending radius: 5" / 127 mm•Minimum bending radius: 3-1/3" / 89 mm•Maximum tube capacity: 3" / 76 mm / .095 wall•Standard die pack (BB-1): 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2"•Top cylinder working force: 60,000 lbs. / 27,216 kg•Dimensions: 42" x 62" x 31" / 1,067 mm x 1,575 mm x 787 mm•Standard motor: 5 Hp / 208 - 230 VAC / 60 Hz / 1 pH•Shipping weight: 1,264 lbs. / 573 kg•Shipping dimensions: 48" x 70" x 30" / 1,219 mm x 1,778 mm x 762 mm
Bend-Pak BB2 Hydraulic Pipe Bender
Page 15
www.equipmentafrica.net
Specifications – SA40
Lifting Capacity 4000 kg
Locking release Manual
Min Height 100 mm
Lifting Height 1900mm
Power of motor 2.2 kw
Oil Pressure 18 MPa
Power Supply 220v
Lifting time 50 s
Lowering Time 40 s
SA40 Two Post Lift with base plate – 4 ton capacity (Manual Release)
Floor plate design, more suitable for lowceiling workshops. Single side Manuallock release. Dual cylinders located inMaster and slave column. Dynamic test115% of the rated capacity. Static test:150% of the rated capacity. Dual anticskidding safety device from columnladder safety to hydraulic seal protection.Special hydraulic system designed toavoid overload running. ABS control box,24v low voltage control system. Highstrength chain drive system. High qualityseals from Italy. Quality power rack. CECertified - Red
Specifications – SB40
Lifting Capacity 4000 kg
Lock release Manual
Min Height 110 mm
Lifting Height 1900mm
Column Height 3722mm
Power of motor 2.2 kw
Oil Pressure 18 MPa
Power Supply 220v/380v
Lifting time 50 s
Lowering Time 40 s
Clear floor design makes under-vehicle servicemore convenient. Manual lock release on bothsides. Dual cylinders located in Master and slavecolumn. Dynamic test 115% of the rated capacity.Static test: 150% of the rated capacity. Dual antiskidding safety device from column ladder safetyto hydraulic seal protection. Special hydraulicsystem designed to avoid overload running. ABScontrol box, 24v low voltage control system. Highstrength chain drive system, High quality sealsfrom Italy. CE Certified - Red
SB40 Two Post Lift , Base free – 4 ton capacity (Manual Release)
Specifications – SAE40
Lifting Capacity 4000 kg
Locking release Electrical
Min Height 100 mm
Lifting Height 1900mm
Power of motor 2.2 kw
Oil Pressure 18 MPa
Power Supply 220v
Lifting time 50 s
Lowering Time 40 s
Reinforcement base plate for uneven floor
Floor plate design, more suitable for lowceiling workshops. Single side electricallock release. Dual cylinders located inMaster and slave column. Dynamic test115% of the rated capacity. Static test:150% of the rated capacity. Dual anticskidding safety device from columnladder safety to hydraulic seal protection.Special hydraulic system designed toavoid overload running. ABS control box,24v low voltage control system. Highstrength chain drive system. High qualityseals from Italy. Quality power rack. CECertified - Red
Page 16
SAE40 Two Post Lift with base plate – 4 ton capacity (Electric Release)
Reinforcement base plate for uneven floor
SBE40 Two Post Lift , Base free – 4 ton capacity (Electric Release)
Specifications – SBE40
Lifting Capacity 4000 kg
Lock release Electric
Min Height 110 mm
Lifting Height 1900mm
Column Height 3776mm
Power of motor 2.2 kw
Oil Pressure 18 MPa
Power Supply 220v / 380v
Lifting time 50 s
Lowering Time 40 s
Clear floor design makes under vehicle servicemore convenient. Single side electrical lockrelease. Dual cylinders located in Master andslave column. Dynamic test 115% of the ratedcapacity. Static test: 150% of the rated capacity.Dual antic skidding safety device from columnladder safety to hydraulic seal protectionSpecial hydraulic system designed to avoidoverload running. ABS control box, 24v lowvoltage control system. High quality seals fromItaly. High strength chain drive systemQuality power rack - Red
Specifications – SBE40H
Lifting Capacity 4000 kg
Lock release Electric
Min Height 110 mm
Lifting Height 1900mm
Column Height 3800mm
Power of motor 2.2 kw
Oil Pressure 18 MPa
Power Supply 220v / 380v
Lifting time 50 s
Lowering Time 40 s
Clear floor design makes under vehicle service moreconvenient. Single side electrical lock release. Dualcylinders located in Master and slave column.Dynamic test 115% of the rated capacity. Static test:150% of the rated capacity .Dual antic skiddingsafety device from column ladder safety to hydraulicseal protection Special hydraulic system designed toavoid overload running. ABS control box, 24v lowvoltage control system. High quality seals from Italy.High strength chain drive system, Quality power rack- Red
SBE40H Two Post Lift , Base free – 4 ton capacity - Extended Height (Electric Release)
Specifications
Lifting Capacity 5000 kg
Lifting Height 1850 mm
Minimum Height 350mm
Secondarylifting weight 3.0T
Power of motor 3.0KW
PowerSupply
110-240V/380-415V3/3PH,50Hz/60Hz
OilPressure
18Mpa
SG4-50T1. 5000kgs/11000LBS Capacity2. Single point manual lock release3. Heavy duty, stainless lifting cable4. Slave runaway adjustable to cater for various wheel base vehicles5. Height limit switch6. With anti-surge valve in case of hydraulic hose burst7. Cable anti-break device to double ensure the safety8. ETL and CE certified motor9. Single hydraulic cylinder hidden away under the runaway for Min exposure and Max reliable performance
Page 17
www.equipmentafrica.net
IM - LR30 Low Level Lift
SpecificationsSupply voltage : 220VPower : 750WMax. lifting weight 2.5TMax. Lifting height 580mmLowered height 80mmTotal weight 375KG
SpecificationsSupply voltage : 220VPower : 2.2kWMax. lifting weight 3000kgMax. Lifting height 1000mmLowered height 105mmTotal weight 627KG
Lifting capacity: 2800kgMax. lifting height: 400mmMin. height: 120mmPlatform length: 1350mmPlatform width: 650mmApprox. Weight: 550 kgAir OperatedDouble Air Bellow
IM – LR45 Heavy Duty Low Level Lift 4.5 ton
Lifting capacity: 4500KGMax. lifting height: 580 mmMin. height: 80 mmPlatform length: 1400 mmPlatform width: 580 mmProduct Length: 2100 mmProduct Width: 1900 mm
IM– ABL2 Air Bellow Low Level Lift
Page 18
Lifting capacity: 3000KGMax. lifting height: 1830 mmMin. height: 110 mmPlatform length: 1475-1975mmPlatform width: 660 mmAir supply pressure 6-8barWeight 1045kg
GHML 30B
GHSL 110
Eurotek – Air Bellow Low Lift
Maximum capacity 2700 kgMinimum height 115 mmMaximum height 500 mm without armsOperating pressure 7 barWeight 520 kg complete with armsPlatform width 2000mmPlatform length 1350mmPlatform length with arms extended 2300mmLength of lifting arms 600mmLength of drive on ramps 1200mmWidth of drive on ramps 500mm
www.equipmentafrica.net
Page 19
www.equipmentafrica.net
Standard Pit rack 4.3mAlso available in 5m & 5.5mNo CablesNe leveling of rampNo maintenance
Specification
Pit Racks
Detroit Compressors
Equipped with preset and manual inflation * Two outlets fornitrogen, this product can inflate two tyres at the same time. *It is also equipped with an air outlet to fill air. * Equipped withfour foot casters * Generates * Nitrogen from your compressedair *2 Pre-Filters / LED display * 55L internal Nitrogen StorageTank. * Remains at last setting * Audible and visual end of thecycle signal indicators * Automatic vacuum supply andnitrogen-fill. Power Requirement 100-240Vac 50/60Hz *Operating Temperature -20º to 70ºC * Compressed Air InputRange 6-8.5bar * Nitrogen Purity >97% * Nitrogen Output70L/min @ 9bar/900kPa * Maximum Nitrogen Pressure inTank 800kPa/8bar * Accuracy +/-1 psi, 7 kPa, 0.07 bar * Unitsof Measurement psi, kPa, bar * Suitable for cars and lighttrucks, Green
PN-8890 Nitrogen Generator Cars & HeavyTrucks
Product Features:Auto-start inflation * Automatic zero drift adjustment * Remainsat last setting * Audible and visual end of cycle signal indicators* LCD display * 4 x 8m standard hoses * 4 Nitrogen outlets to fillNitrogen * Equipped with four foot casters * Generates Nitrogenfrom your compressed air * External 120 liter nitrogen storagetank * Power Requirement 110/240Vac / 50-60HZ * PowerConsumption 30W * Operating Temperature Range -20 C to70C * Compressed Air Input Range 6-8.5bar / 600-850kPa *Nitrogen Purity > 97% * Nitrogen Output 167L/min @ 9bar /900kPa * Maximum Nitrogen Pressure 8bar / 800kPa * Nitrogenstorage Tank * External 120 liters Suitable for Cars, LightTrucks – Colour - Green
PN-8850 Nitrogen Generator Cars & Light Trucks
Page 20
Auto-start inflation * Automatic zero drift adjustment * Remainsat last setting* Audible and visual end of the cycle signalindicators * LCD display * 2 x 8m/26ft standard hoses * 4 airoutlets allow simultaneous inflation of up to 4 tires* AutomaticNitrogen Purge and Fill * 55L internal * Nitrogen StorageTank. cycle(N2P) * Power Requirement 100-240Vac50/60Hz * Operating Temperature -20º to 70ºC *Compressed Air Input Range 6-8.5bar * Nitrogen Purity 95-99.99% * Nitrogen Output 70L/min (2.5cfm) @9bar/900kPa * Maximum Nitrogen Pressure in Tank800kPa/8bar * Accuracy +/-1 psi, 7 kPa, 0.07 barUnits of Measurement psi, kPa, bar – Green colour
PN-8830 Nitrogen Generator
NPA - Nitrogen Purity Analyser
Product Features:It is equipped with an air outlet to fill air. It is equippedwith a Nitrogen outlet to fill Nitrogen * Equipped withfour foot casters * Generates Nitrogen from yourcompressed air * 2 Pre-Filters * External 120 liternitrogen storage tank * 10m standard hose supplied *Power Requirement 110/240Vac / 50-60HZ * PowerConsumption 25W * Operating Temperature Range -20? C to 70? C * Compressed Air Input Range * 6-8.5bar/ 600-850kPa * Nitrogen Purity > 97% * Nitrogen Output236L/min @ 9bar/900kPa * Maximum Nitrogen Pressure10bar / 1000kPa * Nitrogen storage Tank External 120liters * Suitable for Cars, Light Trucks, Heavy Trucks,Colour Green
PN-8820 Nitrogen Generator
RIM REPAIR SYSTEM
Page 21
www.equipmentafrica.net
Height: 1605mmDepth: 1098mmWidth: 1410mmWorking Pressure: 140 barNet Weight: 362 kgHydraulic Engine: 0,55kW / 0,7hpWorking Engine: 0,75kW / 1hpRotating Speed: 250rpm
Page 22
www.equipmentafrica.net
RIM POLISH & CLEANING SYSTEM
Height: 443mmDepth: 596-896mmWidth: 542mmPolishing working engine: 1,1kW / 1,5hpPolishing brush size: Max:X240x30
Min:X100x30Polishing rotating speed: 280 rpmNet weight: 32kg
Page 23
www.equipmentafrica.net
Diamond Cutting Machine
IPC type Descriptions: A1. Hardware17 inch touch screen industry integrated machine (stable Intel chipsetindustrial Solutions) 2. Quad core CPU/ SSD hard stick/large capacity DRR3 memory/ USB3.0/WIFI module 3. 10-point touch capacitive screen/1000:1high contrast/16.7M dynamic colour/1280×1024 4. Metal casing cover, low power consumption (no fan), dust proof, Anti interference, high and low temperature. 5. Wireless key & mouse are set up and the mouse can be used together with the screen.6. One year warranty.
Standard configuration:1. Wireless mouse & key 1 set2. Diamond inner cutter 2 set3. Diamond outer cutter 1 set4. Special ordered 3 soft jaws 1 set5. high precision prob system 1 set6. adjustable X stroke 4 station carrier7. light system8. automatic lubrication system9. Cooling system: water cooling system;10. full covered safety door11.Training videos12. Tool case
ITEMSMax. swig over bed (mm)(inch)Max. Diameter of alloy wheel(mm) (inch)Max. Stroke of the X-axis(mm)Max. Stroke of the Z-axis (mm)Width of the rail (mm)Length of the rail (mm)Size of the three-jaw chuck (inch)Range of spindle speed (RPM)Spindle speed controlSpindle bore (mm)Taper of spindle boreTaper of spindle noseAdjustable stroke of carrier in X directionMax. size of tool postStations of tool carrierMin. setting unit of motorMoving speed of postMotor power7.5KWMachine size (L/W/H) (mm)Package sizeNet weight
WRM28H-PCΦΦ
ΦΦ
770(30')710(28')
390880300
132013'
50~2000Automatic
821:20( 90)
A2-10100mm
25×25mm4 position
(Z)long 0.001mm, (X) cross 0.001mm(Z) long 8m/min, (X) cross 6m/min
Motor power7.5KW2200/1620/18702300/1720/2170
2400KGS
A2. Software 1. Self developed professional wheel repair software. 2. Friendly man- machine interface, easy to learn and the people without professional raining can learn the operation easily in one hour. 3. Detection, optimization and cutting can be finished in one system in a time. 4. The software can support the repair of curves by parts, make the surface of wheel perfect by cutting minimum cutting quantity. 5. The customer can establish their own database of different models of wheels and the saved data can be used in the cutting of same model. 6. Support the remote assistance, and any problems can contact with our company to start the after sale service.7. Software support remote upgrade, enjoy life free upgrade to the latest version 8. Training video of the operation.
Ratchet Type Jack Stands
Model Capacity Min Height Max Height Length Width G.W N.W
Y450301 3 Ton 268 425 190 170 7.5 7
Y451600 6 Ton 394 597 270 240 15.2 13.8
Y451200 12 Ton 440 710 310 260 27.1 26
All stands have a heavy duty robot welded frame, and a multi -position ductile ratchet bar. The quick adjustment mechanism secur elylocks into the right location. Includes counter-weighted pawl for safe securing.
Pin Type Type Jack Stands
Model Capacity Min Height Max Height N.W
Y452300 3 Ton 322 465 5.2
Y452600 6 Ton 404 604 11
Pin type support axle stands adjust to multiple height positions. Large support saddle with oil resistant rubber adaptor foroptimal stability and damage free contact; Designed with wide feet for high standard of safety
3 ton capacity. This jack is equipped withthe TURBO LIFTER system, rubber saddleand handle bumper. The professionaluniversal joint release valve makes itpossible to lower the jack with load veryprecisely and free from any risks Thepump pistons (protected with jacket toprevent from intrusion of dirt) are placedat a 45 degree angle so a completepumping stroke will always be utilized. Thejack has a chrome main ram.
Y420303 Trolley Jack, Turbo Lifter 3 tonCapacity
Model Capacity MinHeight
MaxHeight
Length Width N.W
Y411350 1.35 Ton 80 380 500 240 10
Y420303 3 Ton 130 490 720 360 41
Y420200 2 Ton 140 800 1250 470 58
Y420301 3 Ton 130 600 1305 320 66
Y420500 5 Ton 150 685 1420 355 95
Y421000 10 Ton 160 685 1700 510 145
CIZ-TJ20 20 Ton 180 600 1910 340 165
Y432001 20 Ton 185 373 580 320 47
Y432030 30/15 Ton 150 300 600 305 45
Y432001 - 20 ton capacity. Thisheavy duty model is designed forservicing jobs in the truckindustry. This jack has an extraextension screw in addition to 3saddles that can be placed on topof each other for added height.Chrome main ram and aluminumair motor guarantee optimumlifetime. Air filter, connected tohose included.
All models are equipped with afoot pedal and ergonomicallydesigned handle. These jackshave a chrome main ram andprofessional universal jointrelease valve that makes itpossible to lower loads veryprecisely and free of any risks.
Long chassis Trolley Jack
Winntec Y432001 Air service Jack
Winntec Y432030 Telescopic Air Service Jack
The perfect All-Rounder. This 30/15T jack takes Winntecair-hydraulic technology to its very extreme. Its firststage lifts 30T and reaches 220mm. The second stage,with 15T capacity, reaches another 80mm resulting in a300mm maximum height without extensions. Witha150mm low profile this jack is ideal for modern lowground-clearance vehicles. The jack comes with 3extensions (10-70-120mm) and has a manual valve thatcan close the oil channel (during transport).
Y411350 Trolley Jack, Aluminum 1.35ton Capacity
1350 kg. This ultra light jack isequipped with rubber saddle andnylon wheels. The professionaluniversal joint makes it possible tolower the jack with load very preciselyand free of any risk. The pump pistonis placed at a 45° angle so a completepumping stroke will always be utilized
Page 24
www.equipmentafrica.net
IM-QD52 PneumaticTyre Spreader IM- SD-2 Manual Tyre Spreader
Pneumatic upright tyre spreader for cars, light trucksand minibuses tyres. It is designed for locking andsubsequent spreading of tyres. The machine allowsperforming such functions as inspection, sanding,polishing, dust extraction and patching. The machineis operated by way of two rubber coated footpedals.(Air required). Tyre width: 100-375mm
DB-88 Overturn Vulcanizing Machine
IM- AAT400 Tyre Caddy
Stack Height1500mmWeight17kgPacking size 850 x 600 x1530mmDue to its jaws and easy manoeuvrability, it
allows a pile of tyres to be loaded withouthaving to touch them by hand
DB-88 FeaturesIt can vulcanize any part of model 750-16 to model1000-20 tires in single surface or double surfaces. Itcan maintain constant temperature automaticallyto ensure the temperature required during tirevulcanization. It can raise, lower or overturn theoperating bracket to vulcanize according to therepair position of the tires of different models. It isequipped with five moulds in different angle and apurpose made heat conduct sand bag, which canensure the repaired tire more conforms to thenormal condition
FeaturesThe hook can be adjusted according to thetyre width for medium-sized and smalltyres.
The operating platform can be turned toany place with ideal light during tyrerepairing.
Page 25
www.equipmentafrica.net
Wheel dolly – roll, lift, twist, lower. Easy installation andde-installation of truck wheel assemblies.1 man control,Heavy-duty industrial bearings. 3 positions for rollersdepending on size of wheel. Great tool for every servicetruck. Avoid damage to wheel bolts and expensive modernrims. For all wheels from 6,5 – 22,5
Truck wheel dolly – Heavy Duty
Truck wheel dolly - 500kg