Concrete Pave Stones

Carriage Stone™

© 2015 by Pavestone, llC. All rights reserved. Pavestone (logo), Creating Beautiful landscapes®, and Carriage Stone™

are trademarks of Pavestone, llC.

iCPi Charter MemberWorld Wide Pavers

www.pavestone.com

• Atlanta, GA: (770) 306-9691

• Austin/San Antonio, tX: (512) 558-7283

• Bowman, SC: (803) 829-1731

• Boston, MA: (508) 947-6001

• Charlotte, nC: (704) 588-4747

• Cincinnati, oH: (513) 474-3783

• Colorado Springs, Co: (719) 322-0101

• dallas/Ft. Worth, tX: (817) 481-5802

• denver, Co: (303) 287-3700

• Hagerstown, Md: (240) 420-3780

• Houston, tX: (281) 391-7283

• Kansas City, Mo: (816) 524-9900

• las Vegas, nV: (702) 221-2700

• new orleans, lA: (985) 882-9111

• Phoenix, AZ: (602) 257-4588

• Sacramento/ Winters, CA: (530) 795-4400

• St. louis/

Cape Girardeau, Mo: (573) 332-8312

• tuscumbia, Al: (256) 383-5366

PlEASE CHECK WitH A PAVEStonE rEPrESEntAtiVE For AVAilABilitY.

Carriage Stone™

SKU# CM 038v8 02/15

This unique pave stone captures the timeless appearance of natural granite sets. The pattern and texture combination lends itself to the European oldworld look. Carriage Stone™ used in repeating sets or as an accent, stands alone as a classic paving product. It is available in standard and tumbledHeritage™ Series finishes and in a variety of colors.

ProdUCt inForMAtion

Carriage Stone™ is available in a thickness of 3 1/8"* = 80mm when

split. Quantity/sq. ft. approximately 4.5 stones.

Carriage Stone™ is made from a "no slump" concrete mix. Made under pressure and high frequency vibrations, Carriage Stone™ has acompressive strength greater than 8000psi, a water absorption maximum of 5% and will meet or exceed ASTM C936 except for Section 5.1where the unit's face area may be > 101 in.2.

CoMPoSition And MAnUFACtUrE

inStAllAtion

inStAllAtion PAttErnS

Complete installation & specification details are available by contacting your

Pavestone Company Sales representative.

note: Colors are shown as accurately as possible in brochures & samples, but due to the nature ofthe product, regional color differences and variables in print reproduction, colors may not matchexactly. For best results in maintaining color consistency, pavers must be installed from several cubesat a time. Efflorescence, a whitish, powder-like deposit, may appear on concrete pavers. This is anatural occurrence in any concrete product and will usually wear off over time.

1. Excavate unsuitable, unstable or unconsolidated subgrade material andcompact the area which has been cleared. Backfill and level with densegraded aggregate suitable for base material (typically 4-6 in. of compactedbase for light vehicular and pedestrian traffic) or as otherwise directed bySite Engineer/Architect/Landscape Architect.

2. Place bedding course of washed concrete sand conforming to the gradingrequirements of ASTM C-33 to a uniform depth of 1-11/2 in. (25-38mm)screeded to the grade and profile required.

3. Unsplit units shall be split with a force break cutting device, midpoint of theunit transverse to the unit’s long dimension, to produce a broken facedproduct measuring nominally 4 x 4 x 3". Install broken face up.

4. Install Carriage Stone™ with joints approximately 1/8 in. to 3/16 in.

5. Where required, cut pavers with an approved cutting device to fit accurately,neatly and without damaged edges.

6. Tamp pavers with a plate compactor, uniformly level, true to grade and freeof movement.

7. Post compaction, spread and sweep dry ASTM C 33 or ASTM C 144 sandover the entire paving area.

8. Make one more pass with plate compactor to fill joints with sand.

9. Sweep paver surface clean for final acceptance by owner/owner’s agent.

APPliCAtionS

Urban Street Paving • Entrance Areas • Porte-Cocheres • Crosswalks

Esplanades • Light Duty Parking Lots • Residential Driveways

Patios • Walkways • Medians • Pedestrian Malls • Sidewalks

Terraces • Garden Pathways • Pool Decks • Roof Gardens

typical Cross Section of Concrete Paver installation

Sand-Filled Joints

Pavers

Sand

Base

The Carriage Stone™ is approximately 4 x 4 x 6" that is split and the broken

face installed up so that the effect is that of cracked granite sets. When the

stone is split you will end up with a stone approximately 4 x 4 x 3".

ProdUCt iS Sold UnSPlit. Check with your local Pavestone Company

representative for splitting options.

Runner Bond

Un-split Carriage Stone™

Nominal Dimensions 3 7/8 W x 6 1/4 L x 3 7/8" H 99mm x 160mm x 99mm Wt./Stone 7.78 lbs.Stones/Pallet 336Approx. Wt./Pallet 2,700 lbs.Sq. ft./Pallet 73Product Number 203

Split Carriage Stone™

Nominal Dimensions 3 7/8 W x 3 7/8 L x 3 1/8" H 99mm x 99mm x 80mmSq. ft./Pallet 73Stones/Pallet 672

* Fractional dimensions are nominal.

(Shown Split)