canrig power catwalk

440
Revision April 2011 i Table of Contents SECTION 1: How To Use This Manual......................................................................................... 1-1 SECTION 2: Operating Specifications......................................................................................... 2-1 SECTION 3: General Overview..................................................................................................... 3-1 SECTION 4: Installation Procedure ............................................................................................. 4-1 SECTION 5: Operating Procedure ............................................................................................... 5-1 SECTION 6: Maintenance ............................................................................................................. 6-1

Upload: franklin-jose-almera-acosta

Post on 27-Nov-2015

3.525 views

Category:

Documents


350 download

TRANSCRIPT

  • Revision April 2011 i

    Table of Contents

    SECTION 1: How To Use This Manual......................................................................................... 1-1

    SECTION 2: Operating Specifications......................................................................................... 2-1

    SECTION 3: General Overview..................................................................................................... 3-1

    SECTION 4: Installation Procedure ............................................................................................. 4-1

    SECTION 5: Operating Procedure ............................................................................................... 5-1

    SECTION 6: Maintenance ............................................................................................................. 6-1

  • Canrig Automated Power Catwalk

    ii Revision April 2011

  • Contents and Related Publications

    Revision April 2011 iii

    Drawing and Parts List

    SECTION 7: Parts 7 : Catwalk Assembly7A : Carrier7B : Ramp and Lift Arm7E: Electrical

    Related Publications:

    PRODUCT BULLETINS Located @www.canrig.com

    COMPONENT LITERATURE Located on CD

  • Canrig Automated Power Catwalk

    iv Revision April 2011

  • Revision April 2011 1-1

    Section 1: How To Use This Manual

    This complete manual consists of the following:

    OPERATING, MAINTENANCE AND SERVICE INSTRUCTIONS Section 2) Operating Specifications Section 3) General Overview Section 4) Installation Procedure Section 5) Operating Procedure Section 6) Maintenance and Service

    DRAWINGS AND PARTS LIST Section 7) Detailed Drawings and Bill of Materials

    ORDERING PARTS: When ordering parts, please indicate the following: Automated Power Catwalk Serial Number Canrig Part Number and Description Assembly/Drawing Number that calls up the appropriate parts Quantity Required Delivery For USA and International: Canrig Drilling Technology Ltd. 14703 FM 1488 Magnolia, Texas 77354 USA PHONE: 281.259.8887 FAX: (832) 934-1920 EMAIL: [email protected]

    For Canada: Canrig Drilling Technology Canada Ltd. 7475 51st Street SE Calgary, Alberta T2C 4L6 Canada PHONE: 403-237-6400 FAX: 403-269-3090 EMAIL: [email protected]

  • Canrig Automated Power Catwalk

    1-2 Revision April 2011

    Below is a brief description of each section. OPERATING, MAINTENANCE and SERVICE INSTRUCTIONS SECTION 2: OPERATING SPECIFICATIONS This section provides specifications and torque characteristics of the Canrig Automated Power Catwalk. SECTION 3: GENERAL OVERVIEW This section provides a introduction and an overview of the available features of the Canrig Automated Power Catwalk. SECTION 4: INSTALLATION PROCEDURE This section contains the installation procedure of the Canrig Automated Power Catwalk. SECTION 5: OPERATING PROCEDURE This section contains the operating instructions and commissioning procedure for the Canrig Automated Power Catwalk. SECTION 6: MAINTENANCE and SERVICE This section contains the maintenance, lubrication, shipping and storage and troubleshooting literature of the Canrig Automated Power Catwalk. SECTION 7: DRAWINGS and PARTS LIST This section provides a detailed breakdown of the CANRIG AUTOMATED POWER CATWALK, and is divided into sections as described below. Drawings that identify component parts are accompanied by an Engineering Bill of Materials which lists Canrig part numbers for each item. 7) Catwalk Assembly 7A) Carrier 7B) Ramp and Lift Arm 7E) Electrical and Hydraulic Schematics

  • Section 1: How To Use This Manual

    Revision April 2011 1-3

  • Canrig Automated Power Catwalk

    1-4 Revision April 2011

  • Section 2: Operating Specifications

    Revision April 2011 2-3

    Automated Power Catwalk Model 3000 Specifications

    Description Imperial Metric Tubular Length, Max 45 Ft, Range 3, Single 13.7 m, Range 3, Single

    Tubular OD, Max 20 Inches 50.8 cm

    Tubular Weight, Max 10,000 Lbs 4,535 Kgs

    Cycle Time, Approx 20 Seconds (Catwalk Base to Rig Floor)

    20 Seconds

    Drill Floor Height 18 to 35 Ft 5.05 m to 10.6 m

    Catwalk Height 26 or 42 Inches 66.0 cm or 107.0 cm

    Dimensions, Working 9.5 Ft W x 60 Ft Plus Height of Rig Floor = L

    2.9m x 18.29m Plus Height of Rig Floor = L

    Dimensions, Transportation

    10.5 Ft H x 9.5 Ft W x 60 Ft L 3.2m x 2.9m x 18.29m

    Weight, Unloaded, Approx

    57,000 Lbs 25,850 Kgs

    HPU Drive System Electric Electric

    HPU Power 75HP 56 Kw

    Pipe Rack Capacity 5000 Lbs per Rack 2273 Kgs

    Carrier Cable Capacity

    2000 Ton Miles

  • Revision April 2011 3-1

    SECTION 3: GENERAL OVERVIEW

    Automated Power Catwalk ........................................................................................................ 3-3

    Safety Notices....................................................................................................................... 3-5 Pipe Rack .................................................................................................................................. 3-6 Indexers .................................................................................................................................... 3-7 Safety Pins ................................................................................................................................ 3-8 Kickers ...................................................................................................................................... 3-9 Skate ....................................................................................................................................... 3-10 Carrier Lift Winch .................................................................................................................... 3-11 Control Console ...................................................................................................................... 3-12 Wireless Control ...................................................................................................................... 3-15 Main Electrical Box .................................................................................................................. 3-16 Hydraulic Power Unit ............................................................................................................... 3-17

  • Canrig Automated Power Catwalk Model 3000

    3-2 Revision April 2011

  • Section 3: General Overview

    Revision April 2011 3-3

    AUTOMATED POWER CATWALK

    The Automated Power Catwalk is used to move tubulars between the pipe rack area and the drilling floor. It consists of a Catwalk, Ramp and a Carrier assembly and a series of tubular movement devices. The unit is controlled by a computer through controls on the Control Console or from a Wireless Control. The Automated Power Catwalk, see Figure 1, has three folding hydraulic Pipe Racks and three Indexers on either side. The Automated Power Catwalk also contains the Hydraulic Power Unit and Control Console on the Drillers side, flare end. The Ramp is hinged to the Automated Power Catwalk and rotates up to rest on the drilling floor for operation. It is chained to the Rig Floor for safety. The Ramp has a Carrier Lift Winch mounted on the under side. The Carrier, see Figure 2, is used to carry tubulars to and from the drill floor. It is normally stored retracted flush inside the Automated Power Catwalk. When loaded with a tubular, the Carrier Lift Winch moves the Carrier up and down the Ramp. The Carrier has three Kickers and three Safety Pins on either side and includes the Skate and Skate Winch assemblies. The major components and layout are illustrated in Figure 1.

  • Canrig Automated Power Catwalk Model 3000

    3-4 Revision April 2011

    CATWALK SET-BACK

    CARRIEROVERHANG

    RIG FLOOR

    CARRIERLIFT WINCH

    RAMPLIFT ARM

    CARRIER

    CATWALK

    MIDDLERAMP END FLARE END

    MAINCONTROL BOX

    PIPE RACKARMS (x6)INDEXERS (x6)

    OFF DRILLERSSIDE

    FRO

    NT

    EDG

    E O

    F RIG

    FLO

    OR

    DRILLERSSIDE

    Figure 1: General Assembly

    Figure 2: Carrier Detail

    Control Console

  • Section 3: General Overview

    Revision April 2011 3-5

    Prior to performing any work on the Automated Power Catwalk, please make sure you read this important safety information and observe all CAUTION, WARNING, and DANGER safety notations. Safety and informational callouts used in this manual include:

    This label is used to warn against hazards and unsafe practices, which could result in

    severe personal injury or death if proper procedures are not followed.

    This label is used to warn against potential hazards or unsafe practices, which could result

    in severe personal injury and product or property damage if proper procedures are not followed.

    Safety Notices are used to advise personnel to follow safe practices.

    Safety Notices

    Do Do Not Wear personal protective equipment. Hard Hat, Safety Glasses and Safety Boots when operating this equipment.

    Stand on the Catwalk or Pipe Racks when the equipment is in operation.

    Ensure that all personnel are clear of the Catwalk when operating the equipment.

    Have any physical contact with the Indexers, Kickers or Skate when the equipment is in operation.

    Use the designated Lifting Points when lifting the equipment for transportation.

    Operate this equipment without proper training.

    Read all Warnings and Cautions before operating the equipment.

    Double stack Tubulars on the Pipe Rack Arms as this prevents the indexers from operating properly.

    Keep the equipment clean and free from contamination at all times.

    Stand near the Hydraulic Leg Pads when the Hydraulic Legs are being deployed.

    Perform periodic maintenance. Overload equipment. Check Specifications and Operating Instructions.

    Use only recommended lubricants and hydraulic oil.

    Ensure Hydraulic Oil is filtered, when oil is being added to the tank.

  • Canrig Automated Power Catwalk Model 3000

    3-6 Revision April 2011

    PIPE RACK There are three Pipe Racks, see Figure 3, mounted on either side of the Catwalk. Each Pipe Rack swings on a ball mount and is stowed for transport on a shipping support. A short chain secures the Pipe Rack to the shipping support. Cylinder Swing Wedges can be used to hold the Pipe Rack horizontally so it can be swung out 90 degrees for operation. The Wedges can be removed once the Pipe Rack Hydraulic Leg is extended to the ground and the Pipe Rack is supported.

    Figure 3: Pipe Rack The Pipe Rack Hydraulic Legs are operated from the Control Console or from the Wireless Control.

    The maximum capacity of each pipe rack is 5,000 lbs.

    Keep feet out from under Pipe Rack leg while swinging Pipe Rack

    out from or into transport position.

    CYLINDER SWING WEDGES

    BALL MOUNT

    PIPE RACK HYDRAULIC LEG

  • Section 3: General Overview

    Revision April 2011 3-7

    INDEXERS There are three Indexers, see Figure 4, on both the Drillers side and the Off-drillers side of the Catwalk (Figure 1). Each Indexer has two hydraulic cylinders. Operating the outer cylinder lifts the outer end of the Indexer to roll tubulars in towards the Carrier. Operating the inner cylinder lifts the inner end of the Indexer to roll tubulars out of the Carrier toward the Pipe Racks. All of the outer or inner Indexer cylinders on a side of the Catwalk operate simultaneously with one lever. The Indexers may be operated in either direction (inner raise or outer raise) by pushing the appropriate lever in the desired direction on the Control Console or the Wireless Control.

    Figure 4: Indexer

    NOTE Indexers will NOT function when the Carrier is elevated or while

    the Skate is in operation.

    HYDRAULIC CYLINDER

    INDEXER PIPE

    STOPPER PIN

  • Canrig Automated Power Catwalk Model 3000

    3-8 Revision April 2011

    SAFETY PINS There are three Safety Pins, see Figure 5, on each side of the Carrier. The Safety Pins are actuated by Hydraulic Cylinders. The Safety Pins prevent tubulars from rolling across the Carrier when loading, or rolling out of the Carrier when it is being raised or lowered. The Safety Pins extend automatically when the Carrier is elevated. The Drillers side or Off-drillers side Safety Pins can be operated manually when the Carrier is in the fully retracted position by using the Safety Pin toggle switches on the Control Console or the Wireless Control. These are labeled Locator Pin on the Wireless Control. All three Safety Pins on a side operate simultaneously. The Safety Pins can not be lowered unless the Carrier is fully retracted. The Safety Pins will automatically retract only when the Carrier is fully retracted into the Catwalk and none of the switches on the Control Console or Wireless Control are in the up position.

    Figure 5: Safety Pin

    HYDRAULIC CYLINDER

    SAFETY PIN

  • Section 3: General Overview

    Revision April 2011 3-9

    KICKERS There are three Kickers, see Figure 6, on each side of the Carrier. Hydraulic cylinders actuate the Kickers. The Kickers eject tubulars out of the center Carrier groove to either the Drillers side or the Off-drillers side. All Kickers on a side operate simultaneously with one lever. Pushing the appropriate lever on the Control Console or the Wireless Control operates the Kickers. When the Carrier is elevated out of the Catwalk or when the Skate is in operation the Kickers do not work.

    Always ensure that the Skate is not blocking any of the Kickers

    before operating the Kickers.

    Figure 6: Kickers

    KICKER UP

  • Canrig Automated Power Catwalk Model 3000

    3-10 Revision April 2011

    SKATE The Skate, see Figure 7, runs the length of the Carrier and is powered by a hydraulic winch and cable. The Skate is operated from the Control Console or the Wireless Control. The Skate can be operated at any time when the hydraulic pump is on.

    Do NOT use the Kickers if the Skate is in the way.

    Do NOT run the Skate into the stop plates located under the top

    Carrier plate near each end of the Carrier. This will cause damage to the Skate assembly and shorten the life of the skate cables.

    Figure 7: Skate

    SKATE

  • Section 3: General Overview

    Revision April 2011 3-11

    CARRIER LIFT WINCH The Carrier Lift Winch is located under the Ramp, see Figure 8. Cables from the Winch Drum travel up the under side of the Ramp, over two guide sheaves and down the front side of the Ramp in the protective slots. The cables pass under the Cable Guide Block on the front of the Carrier and attach to the Cable Attachment Block located about 2/3 down the length of the Carrier. The Carrier Lift Winch pulls the Carrier up the Ramp and over the drilling floor to mouse hole so tubulars can be delivered to or removed from the drilling floor. The Carrier has a Lift Arm mounted on its underside, which travels inside the Catwalk as the Carrier is pulled up the Ramp. The Lift Arm enters a pocket, which causes the back end of the Carrier to lift up out of the Catwalk. This allows the Carrier to extend across the drilling floor to the mouse hole. The Carrier Lift Winch is operated from the Control Console or from the Wireless Control. The speed of the Carrier travel is computer controlled throughout its range so damage does not occur to the Carrier or Lift Arm during operation.

    Figure 8: Carrier Lift Winch, located under the Ramp.

  • Canrig Automated Power Catwalk Model 3000

    3-12 Revision April 2011

    CONTROL CONSOLE The Control Console, see Figures 9, 10,11, 12 and 13, is located on the Drillers side, Flare End and consists of a Control Bank, an Operator Interface Display, a Motor Running Light, an Emergency Stop Button, Reset Button, Pump On Button, a Start Button, and a Stop Button.

    Figure 9: Control Console

    The Operator Interface Display shows the status of the Catwalk. If an error message

    occurs the Amber Strobe Light flashes.

    The Motor Running Light is illuminated when the electric motor is operating.

    The Emergency Stop Button, when pressed removes power from the electric motor, causes the Catwalk to cease operation, and displays an error message on the Operator Interface Display.

    The Control Bank consists of 3 Switches and 6 Levers to operate the Catwalk and has a hinged Protective Cover.

    AMBER STROBE LAMP PROTECTIVE

    COVER

    CONTROL BANK

    OPERATOR INTERFACE

    DISPLAY

    MOTOR RUNNING LIGHT EMERGENCY

    STOP BUTTON

    TANK OIL LEVEL AND

    TEMERATURE GAUGE

  • Section 3: General Overview

    Revision April 2011 3-13

    Figure 10: Control Bank

    Figure 11: Inside of Control Console A pump motor Auto/Hand switch is located inside the Control Console.

    PUMP AUTO/HAND SELECTOR SWITCH

  • Canrig Automated Power Catwalk Model 3000

    3-14 Revision April 2011

    The Reset Button is used to reset operational Errors and to enable Carrier operation

    from the Control Console when the Wireless Control is disabled or off.

    The Pump Start button starts the hydraulic pump motor. When it is pressed the Catwalk hydraulic system becomes energized and the Catwalk may be operated from either the Control Console or the Wireless Control if it has been enabled.

    The Stop Button stops the hydraulic pump motor.

    The Pump On button loads the hydraulic pump to provide 2000 PSI pressure to

    lower the Carrier and retract the Skate under certain conditions. It does not start the pump motor.

    Figure 12: Control Console, Figure 13: Control Console, Left Hand Side Right Hand Side

    RESET BUTTON

    PUMP ON BUTTON

    PUMP START BUTTON

    PUMP STOP BUTTON

    NOTE DO NOT use the Pump On switch for normal operation.

  • Section 3: General Overview

    Revision April 2011 3-15

    WIRELESS CONTROL The Wireless Control can be used to control the functions of the Catwalk, when it has been enabled.

    Figure 14: Wireless Control

  • Canrig Automated Power Catwalk Model 3000

    3-16 Revision April 2011

    MAIN ELECTRIC BOX The Main Electrical Box, see Figure 15, is located under the removable Catwalk floors directly adjacent to the Electric Motor of the Hydraulic Power Unit. It houses the motor switchgear, computer, electric controls, breakers, fuses, relays, and on some models the main disconnect switch.

    Figure 15: Location of Main Electrical Box

    Opening the Main Electrical Box will expose personnel to 480 -

    600 volts.

    MAIN ELECTRICAL BOX

    75 HP MOTOR

    AND PUMP

    HIGH PRESSURE

    FILTER

    HYDRAULIC OIL COOLER

    MAIN VALVE BANK

    FILTER BYPASS INDICATIOR

  • Section 3: General Overview

    Revision April 2011 3-17

    HYDRAULIC POWER UNIT The Hydraulic Power Unit, Figures 16, 17 and 18, is located on the Drillers Side, Flare End of the Catwalk. The HPU consists of a Hydraulic Tank, Return Filter with Pressure Switch, Pump Case Drain Filter, Tank Breather Filter, Oil Level Sight Glass with Low Level Switch, Oil Heater, Oil Temperature Gauge, Temperature Transmitter, an Electric Motor and Hydraulic Pump. The Electric Motor, Hydraulic Pump, Oil Heater and Temperature Transmitter are located under removable floor panels.

    Figure 16: Hydraulic Power Unit

    MAIN ELECTRICAL

    BOX

    75 HP MOTOR

    AND PUMP

    TANK BREATHER TEMPERATURE

    TRANSMITTER

    RETURN FILTER

    DRILLERS SIDE

    TANK HEATER

    PUMP CASE DRAIN FILTER

  • Canrig Automated Power Catwalk Model 3000

    3-18 Revision April 2011

    Figure 17: Hydraulic Tank

    Figure 18: Return Filter Pressure Gauge

    RETURN FILTER

    PRESSURE GAUGE

    PUMP CASE DRAIN FILTER

    RETURN FILTER

    TANK BREATHER

    OIL LEVEL SIGHT GAUGE

    LOW OIL LEVEL

    SWITCH OIL

    TEMPERATURE GAUGE

    FULL LEVEL

    ADD LEVEL

  • Section 3: General Overview

    Revision April 2011 3-19

  • Canrig Automated Power Catwalk Model 3000

    3-20 Revision April 2011

  • Revision April 2011 4-1

    SECTION 4: INSTALLATION PROCEDURE

    Rigging Up ...................................................................................................................................... 4-3 Set Back Distances ......................................................................................................................... 4-5 Rigging Down ................................................................................................................................ 4-11

  • Canrig Automated Power Catwalk Model 3000

    4-2 Revision April 2011

  • Section 4: Installation Procedure

    Revision April 2011 4-3

    RIGGING UP Ensure, that the Chain Mount is welded to the Rig Floor, see Figure 19.

    Figure 19: Safety Chain Mount

    Ensure, that the appropriate Sub Mount Rest is welded to the Rig Floor if so equipped. Determine the Set Back Distance for the Ramp, see Figure 20. On the ground directly below the v-door edge of the Rig floor, measure a distance

    away from the Rig equivalent to the Set Back Distance and place a marker in that position.

    Move the Catwalk so that the Ramp End aligns with the Set Back Distance marker. Ensure that the Catwalk is level both front-to-back and side-to-side, and is well

    supported on the lease before lifting the Ramp.

    CHAIN MOUNT

  • Canrig Automated Power Catwalk Model 3000

    4-4 Revision April 2011

    CATWALK SET-BACK

    RIG FLOOR

    Height Set Back A Set Back B 18' 0" (216") 15' 5 5/8" (186.3/4") 16' 5 5/8' (198.3/4")20' 0" (240") 17' 5 5/8" (210.3/4") 18' 5 5/8" (222.3/4")22' 0" (264") 19' 5 5/8" (234.3/4") 20' 5 5/8" (246.3/4")23' 5" (282") 21' 0 5/8" (252.3/4") 22' 0 5/8" (264.3/4")25' 0" (300") 22' 5 5/8" (270.3/4") 23' 5 5/8" (282.3/4")26' 6" (318") 24' 0 5/8" (288.3/4") 25' 0 5/8" (300.3/4")30' 0" (360") 27' 5 5/8" (330.3/4") 28' 5 5/8" (342.3/4")33' 0" (396") 30' 5 5/8" (366.3/4") 31' 5 5/8" (378.3/4")35' 0" (420") 28' 7" (344.1/2") 29' 7" (356.1/2)"

    Use Set Back A when the Ramp is directly on the Rig Floor Use Set Back B when the Ramp is on an Optional Sub Mount Rest

    Figure 20: Set Back Distances

    NOTE The measurement is done from the front edge of the Roll

    Bar

  • Section 4: Installation Procedure

    Revision April 2011 4-5

    Lower the Gortrac Pan and the Extension Pan, see Figure 21.

    Before connecting power to the CATWALK, ensure correct voltage is being usedThe correct voltage is marked on the motor housing. Connect tlers

    Figure 21: Gortrac and Extension Pans

    Before connecting power to the Catwalk, ensure correct voltage is being used. The correct voltage is marked on the motor housing. Connect the main power cord to the Appleton connector located beneath the stair landing (Drillers Side, Ramp End). Ensure the connector retaining collar is fully threaded onto the receptacle.

    Figure 22: Main Power Connection

    GORTRAC PAN

    GORTRAC EXTENSION PAN

    The Gortrac pan and extension MUST be FLAT and LEVEL.

    RETAINING COLLAR

    MAIN POWER CONNECTION

  • Canrig Automated Power Catwalk Model 3000

    4-6 Revision April 2011

    Ensure the Pump suction valve at the hydraulic tank is open. The Lever should be in line with the suction hose.

    Figure 23: Pump Suction Valve

    Turn on the main breaker at the MCC. The Operator Interface screen displays the unit status and the strobe will flash indicating an Emergency Stop button error.

    On the first install or whenever there has been wiring changes on the rig the rotation of the Pump MUST be checked. The correct rotation is marked on the pump housing at the suction port. Remove the coupling guard strip so you can see the coupling. Bump the motor using the motor Hand/Auto switch located in the Main Control Box. Consult with electrician to correct rotation.

    Figure 24: Pump Housing Label

    PUMP SUCTION VALVE LEVER

  • Section 4: Installation Procedure

    Revision April 2011 4-7

    Turn on the Wireless Control, see Figure 14. Make sure the E-Stop Button is up.

    Wait for the green light to start flashing and after the second beep, press the green Arm / Reset button on the right side to arm the unit. OK NO ERRORS should be displayed on the Operators screen. If errors exist on the display, correct the error(s) before attempting to run machine.

    Press the Motor Start button. The computer has been programmed with a Carrier Encoder Override control.

    Press the Motor Start button and the Arm / Reset button simultaneously. Then, while holding the buttons, operate the Carrier Lift control lever to un-spool cable on the drum.

    If it becomes necessary to unwind enough cable to cause the Stopped Cable Spoolout Limit error to appear the hydraulic pump will shut off. It will now be necessary to open the Control Console to turn the Pump Auto/Hand Selector Switch to the Hand position to restart the pump. The Carrier Encoder Override control must be used until this alarm can be reset. Be sure the pump switch is returned to the Auto position once this alarm has been cleared. The rig up procedure can now be continued.

    Ensure the Carrier is resting fully toward the hydraulic tank end of its travel before raising the Ramp. This will prevent Carrier track damage on the lower end of the Ramp during rig up.

    Ensure that cables do not bind or pinch while unfolding Ramp.

    The weight of the Ramp is between 13,000 to 15,000 Lbs (5,986 to 6,803

    Kgs)

    Use the rig tugger winches and a pull back line connected to the Lifting Point, see Figure 25, to raise the Ramp. Use the pull back line to prevent the Ramp from falling onto the Rig Floor when it rotates over center.

    NOTE Unwind approximately 5 to 6 feet of cable from the drum so the Ramp can be

    raised without the Carrier picking up and binding on the end of the Ramp.

    Ensure the speed setting is set at slow speed on the Wireless Control.

  • Canrig Automated Power Catwalk Model 3000

    4-8 Revision April 2011

    Figure 25: Ramp Lifting Point

    After Ramp has been lifted past its balance point and is beginning to lower to rig floor watch the lower end of the ramp to ensure the Carrier wheels are not interfering with the track on the Ramp. Ensure the Carrier tracks (channels) do not bind on the ramp posts when entering.

    Once the Ramp is resting on the Rig Floor, pull back the Catwalk using the winch truck so that the lip of the ramp sets on the Ramp hanger with a 1/2 (1.27cm) gap between the lip and the Rig Floor. If resting directly on the rig floor, see Figure 26, keep 1/2 (1.27cm) gap between the sheave saver and the edge of the rig floor.

    Once the Ramp is in position, attach the safety chains to the chain mount on the Rig Floor. Pull the slack in the chain through the chain mount and slide the chain into the slot to secure it.

    LIFTING POINT

  • Section 4: Installation Procedure

    Revision April 2011 4-9

    Figure 26: Safety Chains Secure to Rig Floor. Take up winch cable slack using the Carrier encoder override controls. Ensure that

    cables tighten onto winch properly or re-align cables on drum grooves. Ensure cables pass under the Carrier Cable Guides correctly.

    Swing out the Pipes Racks by removing the safety chain, level the racks with the Pipe Rack Hydraulic Legs and remove the Swing Wedges.

    Figure 27: Pipe Racks Being Extended

    SAFETY CHAINS

    PIPE RACKS SECURED

    PIPE RACK EXTENDED

    Ensure that personnel are at least 5 feet away from the

    Hydraulic Leg Pads when operating the Pipe Rack Hydraulic Legs.

    Keep feet out from under Pipe Rack leg while swinging

    SHEAVE SAVER

  • Canrig Automated Power Catwalk Model 3000

    4-10 Revision April 2011

    Unfold the Stairs, both ends of the Catwalk.

    Figure 28: Stairs, Unfolded

    The unit is ready for operation.

    Figure 29: Rigged Up

  • Section 4: Installation Procedure

    Revision April 2011 4-11

    Rigging Down Maintain power to the Catwalk.

    Start the Hydraulic Pump Motor.

    Ensure Carrier is fully retracted into the Catwalk.

    Press the Motor Start Button and the Reset Button simultaneously and use the

    Carrier Lower control lever to put approx. 5-6 feet slack in the main winch cable (one full revolution of the winch drum).

    Flip up catwalk stairs and secure for transportation (both sets).

    Raise the pipe racks by extending the Pipe Rack Hydraulic Leg, install the Swing

    Wedges, retract the Hydraulic Legs, fold in the Pipe Rack and secure with the Safety Chain. Repeat for the other 5 Pipe Racks.

    Keep feet out from under Pipe Rack leg while swinging Pipe Rack

    out from or into transport position.

    Figure 30: Pipe Racks Folded

    SAFETY CHAIN

  • Canrig Automated Power Catwalk Model 3000

    4-12 Revision April 2011

    Disconnect the Ramp Safety Chains from the Rig Floor see Figure 26.

    Connect the winch truck and the tugger winch line to the Ramp Lifting Point, see

    Figure 25 and pull the Ramp over. Use the tugger winch line as the holdback line to lower Ramp to the Catwalk Deck.

    When the Ramp has been lowered, use the Carrier Raise control lever to remove

    excess slack on the winch cable. Ensure the cables are properly seated in the grooves of the winch drum and the grooves of the cable guides on the Carrier.

    Figure 31: Ramp Winch Cables

    Do NOT over tighten the Winch Cable.

  • Section 4: Installation Procedure

    Revision April 2011 4-13

    Secure the Gortrac Extension Pan and Gortrac Pan.

    Turn off motor, power down the Wireless Control.

    Press the Stop Button on the Control Console.

    Shut down power to the Catwalk.

    Disconnect the electrical power connector from the Catwalk.

    Secure the Ramp.

    Figure 32: Catwalk Rigged Down for Transportation.

  • Canrig Automated Power Catwalk Model 3000

    4-14 Revision April 2011

  • Revision April 2011 5-1

    SECTION 5: OPERATING PROCEDURE Operating Procedure ....................................................................................................................... 5-3

    Wireless Control Operation ................................................................................................. 5-3 Control Console Operation .................................................................................................. 5-5 Loading Tubulars to the Drilling Floor ................................................................................. 5-6 Lowering Tubulars from the Drilling Floor ........................................................................... 5-8

    Operator Interface Display ............................................................................................................ 5-10 Normal Operation .............................................................................................................. 5-10 Setting Pocket, Roller, and Mouse Hole Positions ............................................................ 5-10 Error Codes ....................................................................................................................... 5-12 Status Codes ..................................................................................................................... 5-14

    Trouble Shooting ........................................................................................................................... 5-16 Lowering Carrier from Overshoot ...................................................................................... 5-16

  • Canrig Automated Power Catwalk Model 3000

    5-2 Revision April 2011

  • Section 5: Operating Procedure

    Revision April 2011 5-3

    OPERATING PROCEDURE Wireless Control Operation A key located on the right hand side of the wireless control is used to turn on power. This key can be removed to prevent unauthorized use of the Wireless Control. To operate the Wireless Control, turn on the Power Key. Ensure the red E Stop Button is not pushed down. Wait for two beeps and then press the green Arm/Reset button to enable radio communication. Use the green Arm / Reset button located above the key to enable (arm) the Wireless Control after power up or to reset operational errors. Every time power is supplied to the Catwalk or if power is interrupted then restored, the computer seeks communication with the Wireless Control. The error code Wireless Radio Controller E Stop Pressed or Radio Failure will be displayed until the Wireless Control is turned on and enabled or the Catwalk is put into Control Console Mode. The Wireless Control has Motor Start and Motor Stop buttons located on the left side. These are used to start and stop the electric motor of the Hydraulic Power Unit. Six levers are used to operate the Carrier Lift Winch, the Skate Winch, the Indexers, the Kickers, and the Pipe Racks. Lever 1. Carrier Lift: Up / Down Lever 2. ODS Indexer: Outer Raise / Inner Raise Lever 3. ODS Kicker Lever 4. DS Kicker or V Door End Pipe Rack Up / Down Lever 5. DS Indexer: Outer Raise / Inner Raise or Middle Pipe Rack Up / Down Lever 6. Skate: Fwd / Back or Flare End Pipe Rack Up / Down

    O

    P

    I

    1 2 3 4 5 6

    ODS LOCATOR PIN

    DS LOCATOR PIN

    Figure 33: Wireless Control

    Arm/Reset Button (Green)

    E-STOP

  • Canrig Automated Power Catwalk Model 3000

    5-4 Revision April 2011

    The Wireless Control has 4 toggle switches above the six levers. The middle two are used to actuate the Safety Pins. The left toggle switch is used to enable the Pipe Racks. Push Up to enable the ODS Pipe Racks and while holding the toggle switch, actuate the appropriate lever for the desired Pipe Rack. Pull down on the toggle switch for the DS Pipe Racks. The right toggle switch is used to set Normal or Slow Speed mode. Push the toggle switch forward to set the control for Slow Speed Mode. This mode reduces the speed of the Carrier Lift Winch and Skate Winch to 50%. Option position of this switch is not used. The E-stop button is an emergency stop button which turns off the hydraulic pump electric motor and disables the Wireless Control of the Catwalk. Push down on the button to stop operation of the Catwalk. The green LED will flash rapidly when the E-Stop button has been pressed. Turn the E-Stop button clockwise while allowing it to rise slightly and then press the green reset button to resume operation.

    Figure 34: Wireless Control Toggle Switches

    NOTE These two middle toggle switches on the Wireless Control are labeled Locator Pin but are referred to as Safety Pins throughout this manual as well as the parts manual.

  • Section 5: Operating Procedure

    Revision April 2011 5-5

    Control Console Operation Once power is supplied to the Control Console and the Wireless Control has been turned on and enabled (see Wireless Control Operation) the unit may be operated from the Control Console or the Wireless Control. To put the Catwalk in Control Console Mode perform the following on the console:

    Press and hold Pump Start Button for approximately 5 seconds, see Figure 12. The

    pump will start automatically. Press the Reset Button, see Figure 13. The Catwalk is now in Control Console

    Mode. OK No Errors should be displayed unless an actual error exists.

    This must be repeated every time the power to the Catwalk is interrupted and restored while the Wireless Control is inoperable. Anytime the Wireless Control is turned on and enabled the Catwalk can be operated by either device. The Control Bank has three switches and six levers.

    Pipe Rack ODS/DS Switch - Used with the 3 right hand levers to raise or lower the Hydraulic Legs of the Pipe racks.

    ODS Safety Pin Switch - Raises or lowers the Safety Pins on the Off Drillers Side. DS Safety Pin Switch - Raises or lowers the Safety Pins on the Drillers Side. Carrier Up/Down Lever - Raises or lowers the Carrier. ODS Indexer Lever - Raises the Off Drillers Side Indexers Outer side or the Inner

    side. ODS Kicker Lever - Raises the Off Drillers Side Kickers. DS Kicker Lever - Operates the Drillers Side Kickers or with Pipe Rack switch

    enabled operates the V-door end Pipe Rack Up/Down. DS Indexer Lever - Operates the Drillers Side Indexers or with Pipe Rack switch

    enabled operates the Middle Pipe Rack Up/Down. Skate Lever - Moves the Skate back and forth on the Carrier or with the Pipe Rack

    switch enabled operates the Flare end Pipe Rack Up/Down.

    Figure 35: Control Bank

    NOTE If the Wireless Control is not operational the error code Wireless Radio E Stop Pressed or Radio Failure will be displayed and the unit must be put in Control

  • Canrig Automated Power Catwalk Model 3000

    5-6 Revision April 2011

    Loading Tubulars to the Drilling Floor

    Always ensure Pipe Rack Hydraulic Legs are properly deployed

    before operating the equipment.

    NEVER leave tubulars on the catwalk when the carrier is in operation. All tubulars must be on the Pipe Racks during Carrier operation. Tubulars could roll under the Carrier or Lift Arm causing extensive damage to the equipment.

    Figure 36: Pipe Handler, Cross Section When unloading tubulars from pipe tubs or onto the stationary racks with a loader, make

    sure the tubulars are positioned close to the Ramp end of the Catwalk so when the time comes to load them onto the Carrier, they will clear the Skate properly (Range III pipe and casing typically).

    NEVER double stack tubulars on the Pipe Racks, this prevents loading

    tubulars into the Carrier using the Indexers.

    Set the Pipe Stopper Pin in the appropriate stopper hole so that the Indexer delivers one tubular at a time. The Indexer should catch more than half of the tubular while it is resting against the Stopper Pins.

    Load the Pipe Racks with tubulars. Maximum capacity of each rack in 5000 lbs. Raise the Pipe Racks so tubulars roll up against the Pipe Stopper Pins.

    INDEXER KICKER

    SAFETY PINS

    INDEXER

    PIPE RACK HYDRAULIC

    LEG

    SWING WEDGE

    PIPE RACK ARM

    5000 LB. CAPACITY

  • Section 5: Operating Procedure

    Revision April 2011 5-7

    Ensure the Skate is retracted behind the tubular to be loaded. Actuate the opposite side Safety Pins to prevent tubulars from rolling past the Carrier. Use the Indexer Outer Raise Control to lift one tubular at a time into the Carrier. Once

    the tubular starts rolling, release the lever to drop the Indexer. With practice, it can be anticipated how long to hold the Indexer up to cause the tubular to just roll onto the Carrier and drop into the groove.

    When the tubular is resting in the Carrier groove, use the Skate to push the tubular as far forward as possible without hitting the cable protector slots on the Ramp. This pushes the weight forward making it easier to lift the load.

    The maximum weight capacity of the Carrier is 10,000 lbs. Use the Carrier Lift Control Lever to raise the Carrier up to the drilling floor. The Safety

    Pins raise automatically as the Carrier lifts out of the Catwalk. The Carrier automatically accelerates and decelerates as it lifts. Run the Carrier only as far forward out over the Rig Floor as necessary. It will stop automatically at mouse hole.

    Use the Skate to push the tubular further off of the end of the Carrier into the reach of

    the elevators. Once the elevators have latched, the tubular can be picked up off of the Carrier.

    Depending on the weight of tubular, the Carrier can be left in place to help control the tubular as its pin end slides off of the Carrier or, the Carrier can be lowered slightly sooner to improve cycle time when tripping.

    DO NOT push tubulars up the Carrier as the elevators are lifting it,

    this will cause mechanical damage.

    NOTE The Indexers, Kickers, and Pipe Racks will not operate when the Carrier is lifted

    out of the Catwalk or when the Skate is in operation.

    NOTES There is a Safety Curtain Laser Eye on either side of the Catwalk that will shut

    down the device if the beam is broken while the Carrier is in motion. The Carrier Lift Winch will not operate if there is an object on the Catwalk blocking the Safety Curtain Laser Eye.

    Carrier Encoder Override. The computer has been programmed with a Carrier Encoder Override control sequence. Press Motor Start button and the Arm / Reset button simultaneously. While holding these buttons, operate the Carrier Lift control lever to wind or unwind cable on the drum.

    The Carrier Encoder Override should be used during rig up/down procedure, if the encoder requires re-zeroing, or during certain maintenance procedures.

  • Canrig Automated Power Catwalk Model 3000

    5-8 Revision April 2011

    Lowering Tubulars from the Drilling Floor Set up the Pipe Racks so the tubulars will roll down the Pipe Racks onto the stationary

    racks. Remove the Stopper Pins. Remove the Pipe Rack outboard pins if desired.

    Lift the Carrier up to the Rig Floor and extend it as far over the floor as required. For faster tripping with light pipe, position the Carrier closer to the edge of the Rig Floor. Usually a thread protector is spun on prior to setting the tubular onto the Carrier groove.

    Make sure the Skate is positioned back just behind where you anticipate releasing the tubular from the elevators.

    Push the tubular out and set it on the Carrier groove. Slowly start lowering the blocks. The bottom end of the tubular should slide down the groove as the blocks are lowered. If the tubular sticks, back the Carrier up slowly to increase the angle of the tubular until it begins to slide.

    Prior to releasing the tubular from the elevators, bring the Skate forward to support the tubular so it does not slide back uncontrolled and impact (collide with) the Skate. This could easily damage the Skate or Skate Winch and will seriously reduce the life of the Skate cable.

    Once the elevators have been released, retract the tubular just past the end of the Carrier. Keep the tubulars, especially heavy tubulars, as close to the front end of the Carrier as possible to reduce the load on the Carrier Lift Winch when lowering.

    Retract the Carrier down the Ramp to the Catwalk. Once the Lift Arm rollers have left the Pocket and the Carrier is rolling back on its rear wheels, use the Skate and gravity to slide the tubular back to position it over the Kickers. This can be done while the Carrier is traveling down.

    When the Carrier is fully retracted into the Catwalk, The Carrier Lift Winch will automatically stop and the Safety Pins will lower.

    If the tubular is properly positioned, retract the Skate back away from the tubular, and then actuate the appropriate Kickers to eject the tubular out of the Carrier groove. Raise the inner Indexers to roll the tubular onto the Pipe Racks.

    NEVER leave tubulars on the Catwalk when the Carrier is in

    operation. All tubulars must be on the Pipe Racks during Carrier operation. Tubulars could roll under the Carrier or Lift Arm causing

    extensive damage to the equipment.

    When Tripping Out ensure the Skate supports the Tubular before

    releasing the Tubular from the Elevators.

  • Section 5: Operating Procedure

    Revision April 2011 5-9

    DO NOT position Skate over the Kickers before actuating the Kickers to

    prevent mechanical damage to the Skate mechanism.

    If the tubular is not positioned correctly, you may need to lift the carrier back up the Ramp part way and use gravity and the Skate to position the tubular over the Kickers.

    As soon as the tubular is onto the Pipe Racks the Carrier can be lifted for the next tubular.

    NOTE The Indexers, Kickers, and Pipe Racks will not operate when the Carrier is lifted out

    of the Catwalk or when the Skate is in operation.

  • Canrig Automated Power Catwalk Model 3000

    5-10 Revision April 2011

    OPERATOR INTERFACE DISPLAY The Catwalk uses an Operator Interface Display, see Figure 37, mounted on the Control Console to indicate the operating status of the unit. During operation, the computer is continually monitoring the various systems on the unit and will also indicate errors. Errors are cleared by pushing the Reset Button on the Control Console or the Reset Button on the Wireless Control.

    Normal Operation OK - No Errors The unit is functioning normally. The display also shows the tank temperature and the main system hydraulic pressure.

    Figure 37: No Errors Reading

    Oil Circulation Active - Press F5 to manually start the oil circulate function. The bypass valve will open in the carrier allowing warm oil from the tank to be pumped through the circuit warming the valve assemblies so the unit will operate properly. The oil circulation function will run for 10 minutes and then automatically turn off. Pressing the Reset button on the Wireless Control or the Control Console will turn off the function. The display also shows the oil pressure. Setting Pocket, Roller, and Mouse Hole Positions These are the steps to set the pocket, roller, and mouse hole positions on a PC3000 with PLC program Ver 14 Rel 6 or later, or a PC4000 with PLC program Ver 2 Rel 7 or later, both which have a screen program of Ver 17 or later.

    Bring the carrier to the position you want to set (pocket, roller, or mouse). Start with the pocket position then roller position then mouse hole.

    If this is the first time setting these positions, or the positions have been incorrectly

    set, you may have to go into Carrier Override Mode to move the carrier. To go into Carrier Override Mode you must press the Reset and Motor Start buttons

    at the same time, either on the Wireless Control or the Control Console.

  • Section 5: Operating Procedure

    Revision April 2011 5-11

    Once you have the carrier in the correct position, scroll though the screens using the F1 and F2 keys until you get to the Press F6 To Set Pocket Position (scroll farther if you need to set roller or mouse hole positions).

    Figure 38 - Press F 6 once you have the carrier in the correct position.

    Press F6, this will bring up a confirmation message asking Set Pos Press F6

    Cancel Press F5, Press F6 to set the position, press F5 to cancel.

    Figure 39 - Press F6 again to confirm you want to set the position, or else

    press F5 to cancel. Once you have pressed F6 to set the position, a position set message will be

    displayed for 5 seconds after you press the button.

    Figure 40 - This message is displayed once you have confirmed you want to

    set the position.

    To view the actual positions, scroll through the main screens with the F1 and F2 keys.

  • Canrig Automated Power Catwalk Model 3000

    5-12 Revision April 2011

    Figure 11 - All three position values can be seen by scrolling through the main

    screens. Repeat these steps for each of the carrier set points (pocket, roller, and mouse hole). Once the positions are set, test the unit to ensure the set points are accurate. Error Codes These codes will be displayed on the screen in place of the OK No Errors as seen in Figure 37. Cold Hyd. Oil This indicates that the hydraulic oil is too cold to allow the system to operate. The motor can be started, but none of the functions will operate until the tank temperature is above 23F (-5C). Make sure the Hydraulic Oil tank heater breaker in the main electrical box, Figure 15, is turned on. This error cannot be cleared until the oil temperature is above 23F (-5C). If it is determined that the tank temperature transmitter is not operating correctly, it can be overridden by pushing F4. Hot Hyd. Oil This indicates that the hydraulic oil temperature has exceeded the upper limit of 170F (76C ) resulting in a shutdown. Make sure the cooler fan is running and that the cooler is clean. This error will not clear until the oil temperature is low enough to safely operate the hydraulics. High Hyd. Pressure This indicates that the hydraulic system has over pressured, above 5200 PSI, resulting in a shutdown. Call Canrig Service.

    Hyd Oil Filter Blocked This indicates that the in-tank return filter, Figures 17 & 18, is plugged and the element must be changed. Disregard this error when the oil is colder than 70F (21C). If the oil is above 70F (21C) and there is less that 20 PSI on the filter gauge while operating the Carrier and this error is displayed Call Canrig for Service. Low Hyd. Oil Level In Tank This indicates a low level in the hydraulic reservoir resulting in a shutdown. Check the entire unit for hydraulic leaks. Refill the tank to the correct level as shown by the site glass on the tank, Figure 17. This error will not clear until the tank is properly filled with oil.

  • Section 5: Operating Procedure

    Revision April 2011 5-13

    Safety Curtain Blocked This occurs whenever the Carrier is being lifted or lowered and the safety curtain is interrupted. Remove the obstruction and/or clean the sensor lens, then press the Reset Button on the Wireless Control or the Control Console. If a sensor is damaged, press F6, then press Reset to override the error and continue operation. During rainy, foggy, snowy or dusty conditions you may need to use the Safety Curtain Override until the sensor can be kept clean. The Safety Curtain Override On message will display continuously until it is turned off. If the sensor(s) is damaged Call Canrig for service.

    Before operating with Safety Curtains overridden, make sure

    personnel and objects are clear of the equipment. Safety Curtain Override On This indicates that the Safety Curtain Override function has been activated allowing the unit to operate without safety curtain protection. To turn the Safety Curtain protection back on, Press F6 and then Press the Reset Button on the Wireless Control or Control Console.

    Wireless Radio Controller E-Stop Pressed or Radio Failure This indicates that the Emergency Stop Button on the Wireless Control has been pressed. This error will also be displayed if the Wireless Control is turned off, its battery fails or radio communication is lost. The strobe will flash for 1 minute and then stop. In emergency situations the Electric Motor can be started by using the Auto/Hand switch in the Control Console, pressing F3 will retract the Carrier and pressing F4 will retract the Skate or to continue operation without the Wireless Control put the unit in Control Console Mode.

    Before starting the motor, make sure people are clear of the Carrier.

    Hyd. Tank E-Stop Pressed This indicates that the Emergency Stop Button on the Control Console has been pressed. Pump Not Running Check Motor This occurs if the Motor Start Button is pushed and the motor does not start or if no hydraulic pressure is sensed by any of the three pressure transducers. Check the motor breaker in the Main Electrical Box. Call Canrig Service. This will also occur if the motor is not running in the correct rotation. Pressure Transducer Error This occurs if the computer senses a problem with one of the three pressure transducers on the unit. Press Pump On Button to cause the pump to provide pressure. Now press F3 to lower the carrier or press F4 to retract the skate. Call Canrig Service. Check Winch Encoder Wiring This occurs when the computer senses that the Carrier is being asked to move and there is no input from the Winch Encoder for a period of 4

  • Canrig Automated Power Catwalk Model 3000

    5-14 Revision April 2011

    seconds. There is a problem within the Carrier Lift Winch Encoder circuit. Press the Reset Button. If the Carrier moves and the error re-occurs, call Canrig Service. Carrier Overload Reduce Load This occurs when the Carrier is being asked to raise, and the hydraulic system is at full pressure. Ensure the tubular being raised to the floor does not exceed the rated lifting capacity for the Catwalk. Rated lifting capacity of the Catwalk Carrier is 10,000 pounds (4535 kg). Ensure tubular is always carried as close to the Ramp as possible in the Carrier. Call Canrig Service.

    Stopped Carrier Overshoot This occurs if the Carrier does not stop when at the mouse hole which causes the hydraulic pump motor to turn off. Call Canrig for Service.

    Replace Winch Cables Soon The computer is continually logging the Mega joules or Ton Miles of energy going into the Carrier Lift Winch cables. When the cables reach 80% of the maximum energy allowed by the cable manufacturer, this message will be displayed. Call Canrig for service. Proximity Switch Error or Damaged - This occurs when the Carrier is down and the computer has not received a signal from the Proximity Switch, Figure 39. Call Canrig for service. Stopped - Carrier Moved in Neutral - This occurs when the computer receives a pulse from the Winch Encoder circuit but the computer has not received the input by the operator to move the Carrier. Stopped - Cable Spoolout Limit - This occurs when the operator is attempting to spool out too much Carrier Winch Cable. PLC NOT ATTACHED, Driver 6.0 Open Control Console and ensure the PLC cable is attached to the back of the screen, Figure 11. Call Canrig Service. Comm Error w/PLC, Check PLC Power Open Main Electrical Box, Figure 15, ensure PLC has 24VDC power. Call Canrig Service.

    Status Codes Status Screens show the status, settings and operation of the Catwalk. With the OK screen showing, push the "NEXT" button F1 or the "PREV" button F2 to view the status screens. Ton Mile Count - This indicates the number of Ton Miles for the current Carrier Lift Winch Cables. Carrier Cycle Counter - This indicates the number of times the Carrier has been up to and down from the Rig Floor. Pump Running Time - This indicates, in hours, the pump running time.

  • Section 5: Operating Procedure

    Revision April 2011 5-15

    Encoder Position - This indicates the current position of the Carrier. Moving the Carrier to the Pocket Position, Roller Position or Mouse Hole Position allows the operator to view the settings for these positions. Carrier PSI/Catwalk PSI - This indicates the current hydraulic oil pressures at the Carrier and at the Catwalk. Skate In This displays the raw count from the proportional control input to the PLC. 4000 is maximum (only using Wireless Control). Skate Out - This is the raw output for the Skate movement. 1200 is maximum speed back, 3600 is maximum speed forward, 2400 indicates no movement. Carrier In - This displays the raw count from the proportional control input to the PLC. 4000 is maximum (only using Wireless Control). Carrier Out - This is the raw output for the Carrier movement. 1200 is maximum speed lower, 3600 is maximum speed raise, 2400 indicates no movement. Pump Control Out - This indicates the pressure being supplied by the Pump. Enter Password - This screen is only used by Service Personnel when commissioning the Catwalk.

  • Canrig Automated Power Catwalk Model 3000

    5-16 Revision April 2011

    TROUBLE SHOOTING Lowering Carrier from Overshoot

    These procedures should only be performed by properly trained and

    qualified personnel. For a PC3000 with a PLC program Ver. 14 Rel. 6 or later with a screen program of Ver. 17 or later

    Ensure that no one is in a position where they could be injured if the carrier moves in the following step.

    Open the control console that is mounted on the HPU tank and put the pump switch in the Hand position. The pump will start immediately. If the carrier moves, shut down the pump and call Canrig Field Service.

    The screen on the control console will display Stopped Carrier Overshoot. To

    proceed you must press and hold the Reset on either the Wireless Control or Control Console. The screen will display OK No Errors. While holding the reset scroll though the screens using the F1 or F2 keys until you get to the Press F6 To Set Mouse Position then press F6 once, the screen will then display Set Pos Press F6 Cancel Press F5,

    Figure 42: Press F6 to Display This Screen

    Use the encoder override mode to bring the carrier out of the overshoot condition by lowering the carrier until the end of the carrier is near the roller on the top of the ramp. To use the encoder override mode you must press and hold the Reset and Motor Start buttons simultaneously either on the Wireless Control or the Control Console, Figure 43, in conjunction with the Carrier Up/Down joystick, Figure 44.

  • Section 5: Operating Procedure

    Revision April 2011 5-17

    Figure 43: Reset and Motor Start Buttons on Control Console

    Figure 44: Joysticks on Control Console

    Start Button

    Stop Button

    Reset Button

    Pump On Button

    Carrier Up/Down Joystick

  • Canrig Automated Power Catwalk Model 3000

    5-18 Revision April 2011

    Once you have the carrier in the position described in previous step, press F5 to Cancel. The screen will display OK No Errors, you may continue to operate the catwalk normally.

    Be sure to return the pump to Auto Position.

    If the carrier continues to go into Overshoot call Canrig Field Service.

    The following procedure is for catwalks with a PLC program OLDER than Ver. 14 Rel. 6 with a screen program of Ver. 17

    Remove the floor plates that are above the Main Electrical Box and the catwalk Main

    Valve Bank, Figure 15, adjacent to the cabinet. If it is raining, snowing, foggy or very dusty take measures to prevent contamination of the internal components of the box prior to the next step.

    Open the Main Electrical Box and find the 1.0 Amp breaker for the winch 12VDC

    power and open the breaker. To open the breaker depress and release the push button. It will be labeled with a W, Winch or Carrier Winch. An example of the location of this breaker is shown below.

    Figure 45: Breaker in Main Electrical Box

    This breaker MUST be opened to prevent damage to the winch valve

    manual actuator linkage.

    Ensure that no one is in a position where they could be injured if the carrier moves in the following step.

    Open the control console that is mounted on the HPU tank and put the pump switch

    in the Hand position. The pump will start immediately. If the carrier moves, shut down the pump and call Canrig Field Service.

    NOTE This procedure requires a minimum of two people.

  • Section 5: Operating Procedure

    Revision April 2011 5-19

    Use the Encoder Override Mode and hold the Carrier Up/Down joystick, Figure 44, in the Down position to release the winch brake. To use the Encoder Override Mode you must press and hold the Reset and Motor Start buttons, Figure 43, simultaneously either on the Wireless Control or the Control Console in conjunction with the Carrier Up/Down joystick.

    Simultaneously to releasing the brake (prior step), press the Pump On button to

    load the pump. The pump must discharge 1500 PSI or more to overcome the winch counterbalance valve.

    The Second Person must now use the valve handle, a nine millimeter wrench or

    small adjustable wrench to manually actuate the Winch Control Valve as shown below.

    Figure 46: Winch Control Valve

    Once the end of the carrier is near the roller on the top of the ramp, return the valve to its neutral position and release the controls. You may now close the breaker that was opened in the Main Electrical Box and secure the cabinet lid.

    The screen will display OK - No Errors. You may now return the floor plates to their

    proper location and resume normal operations.

    Be sure to return the pump switch to the Auto Position.

    If the carrier continues to go into Overshoot call Canrig Field Service.

    If the Hydraulic Power Unit is inoperable the above procedures cannot be performed. In this event contact Canrig Field Service.

    CAREFULLY move the wrench or valve handle in the direction shown to lower the carrier.

  • Canrig Automated Power Catwalk Model 3000

    5-20 Revision April 2011

  • Revision April 2011 6-1

    SECTION 6: MAINTENANCE Automated Power Catwalk Maintenance ........................................................................................ 6-3

    Maintenance Schedule ........................................................................................................ 6-3 Cleaning & Inspection ......................................................................................................... 6-3 Greasing Procedure ............................................................................................................ 6-6

    Weekly Greasing ........................................................................................................... 6-6 Other Greasing ............................................................................................................ 6-10

    Hydraulic Filters & Oil ........................................................................................................ 6-12 Hydraulic Oil ...................................................................................................................... 6-13 Skate Cable Maintenance ................................................................................................. 6-14

    Carrier Winch Maintenance ........................................................................................................... 6-15 Lubrication ......................................................................................................................... 6-15 Changing Oil ...................................................................................................................... 6-16 Vent Cleaning .................................................................................................................... 6-17 Mounting Bolts ................................................................................................................... 6-18 Drum Bearing Adjustment ................................................................................................. 6-18

    Inspection ...................................................................................................................................... 6-19 Recommended 1000 Day Inspection ................................................................................ 6-19 Inspection Indication Map: Skid Rollend ........................................................................... 6-20 Inspection Indication Map: Skid Ramp Pivot Post ............................................................. 6-21 Inspection Indication Map: Pipe Rack Arm Mount/Hitch Back .......................................... 6-22 Inspection Indication Map: Ramp Pivot Post ..................................................................... 6-23

    Inspection Indication Map: Ramp Winch Mount ................................................................ 6-24 Inspection Indication Map: Carrier Cable Block and Connections .................................... 6-25 Inspection Indication Map: Carrier Pipe Kicker Mount ...................................................... 6-26 Inspection Indication Map: Lift Arm Pin Mounts ................................................................ 6-27

    Troubleshooting ............................................................................................................................ 6-28 Troubleshooting Flowcharts ............................................................................................. 6-28 Device Operations ............................................................................................................. 6-29

    Carrier Moves Slowly................................................................................................... 6-29 Carrier Will Not Operate Up or Down .......................................................................... 6-30 Carrier Will Not Operate in the Down Direction ......................................................... 6-32 Indexers Will Not Raise ............................................................................................... 6-34 Pipe Racks Move Instead of Kicker, Indexer, or Skate ............................................... 6-36 Safety Pins Will Not Lower .......................................................................................... 6-37 Skate Moves to Ramp End Only ................................................................................. 6-38 Skate Will Not Move .................................................................................................... 6-39

    Electrical System ............................................................................................................... 6-41 Hydraulic Pump Motor Wont Start .............................................................................. 6-41 Pressure Transducer Error .......................................................................................... 6-43 Safety Curtains Always Blocked .................................................................................. 6-44

    Hydraulic System .............................................................................................................. 6-45 High Pressure Shutdown Alarm .................................................................................. 6-45 Hot Hydraulic Oil Alarm ............................................................................................... 6-46 Hydraulic Pump Motor Starts but Turns Off after Two Seconds .................................. 6-48 Hydraulic System Wont Build Pressure ...................................................................... 6-49

  • Canrig Automated Power Catwalk Model 3000

    6-2 Revision April 2011

  • Section 6: Maintenance

    Revision April 2011 6-3

    Automated Power Catwalk Maintenance

    Maintenance Schedule Cleaning & Inspection, Daily. Greasing, See Greasing Procedure. Wireless Control in accordance with Appendix 2 (CD Version Only). Carrier Winch in accordance with Appendix 1 (CD Version Only). The Skate Winch Cable tension adjustment is only required when necessary. Cleaning & Inspection Turn off the system and lock out the electrical power.

    Figure 47: Safety Bar

    Any time the Carrier is elevated and personnel are positioned under the Carrier the Safety Bar must be placed behind the flare end of the

    Carrier and protrude through the holes on both sides of the inner Catwalk wall to prevent lowering of the Carrier, see Figure 47.

    SAFETY BAR

  • Canrig Automated Power Catwalk Model 3000

    6-4 Revision April 2011

    Inspect the Ramp, Carrier Rollers Guides, Pivot Pockets, see Figure 48, Skate Groove,

    Indexers, Kickers, Stop Pins and Gortrac Pan and remove any dirt or debris.

    Figure 48: Pivot Pockets.

    The Gortrac Pan and Extension Pan MUST be kept clear of debris, mud,

    snow and ice as the Gortrac travels back and forth in this area and it can be damaged if it cannot move.

    For Units fitted with a Chain Drive Skate Winch, inspect the drive chain for wear and any looseness of the sprockets. Ensure the chain master link is properly attached and that the chain is well lubricated and tensioned. Chain should have between 1/4- 1/2 droop between sprockets on the slack side.

    Carrier Proximity

    Pivot Pockets

    Carrier Hydraulics Bulkhead

  • Section 6: Maintenance

    Revision April 2011 6-5

    Inspect the Skate Winch cable and drum before each tripping run or once per month for

    signs of wear. Check for broken wires in the cable and excessive grooving in the drum.

    Check the Carrier Lift Winch cables for signs of wear. Check for broken wires in the cable. Ensure cables are not crossed and ride in the correct groove on the Main Winch Drum.

    Inspect the Carrier Lift Winch motor and brake hydraulic lines for signs of wear or leaks. Refer to the Lantec Manual in Appendix 1 for Specific information and Maintenance information on the Carrier Lift Winch.

    Check inside and around the Catwalk for signs of hydraulic leaks. Note: The

    atmospheric vent line in the hydraulic hose bundle located on the Drillers side of the Catwalk under the ramp may expel small amounts of hydraulic oil during operation. Any leakage under normal operating conditions may indicate a potential hydraulic system fault.

    The hydraulic pressure in the lines can reach 5000 psi. Ensure that all

    leaks, frayed or damaged lines are corrected immediately.

  • Canrig Automated Power Catwalk Model 3000

    6-6 Revision April 2011

    Greasing Procedure Weekly Greasing Use multi-purpose lithium complex grease complying with N.L.G.I. classification No. 1 or

    No. 2. Grease each grease zerk on the lift arm shaft.

    Figure 49: Lift Arm, Grease Points. Grease each grease zerk on the Kicker Cylinders and Pivot Assembly and on the Safety

    Pin cylinders.

    Figure 50: Kicker Grease Points.

    GREASE POINT

    (BOTH SIDES)

    GREASE POINTS

  • Section 6: Maintenance

    Revision April 2011 6-7

    Figure 51: Kicker Grease Point

    Figure 52: Pivot Assembly & Safety Pin Grease Points.

    GREASE POINT

    GREASE POINTS

    GREASE POINT

  • Canrig Automated Power Catwalk Model 3000

    6-8 Revision April 2011

    Grease each grease zerk on the Lift Arm rollers shaft and Pillow Block at the rear of the

    Carrier.

    Figure 53: Lift Arm Roller, Grease Points.

    Grease each grease zerk on the Indexer cylinders.

    Figure 54: Indexer Cylinder, Grease Points.

    GREASE POINTS

    GREASE POINTS

  • Section 6: Maintenance

    Revision April 2011 6-9

    Grease each of the two grease zerks on the roller bearings at the top of the Ramp. Grease the Cable Sheave bearings at the top of the Ramp.

    Figure 55: Roller and Sheave Bearing, Grease Points. For units with Non-Sealed bearings, grease the grease zerks on the Carrier Rollers.

    Figure 56: Bottom Carrier Rollers, Grease Points.

    ROLLER GREASE POINTS

    SHEAVE GREASE POINTS

    GREASE POINTS

    (BOTH SIDES)

  • Canrig Automated Power Catwalk Model 3000

    6-10 Revision April 2011

    Figure 57: Top Carrier Rollers, Grease Points. Other Greasing Use multi-purpose lithium complex grease complying with N.L.G.I. classification No. 1 or

    No. 2. Once per month grease the Ramp Pivot.

    Figure 58: Ramp Pivot, Grease Points.

    GREASE POINTS

    GREASE POINTS

    FOR UNITS WITH NON-SEALED

    BEARINGS GREASE BOTH

    SIDES

  • Section 6: Maintenance

    Revision April 2011 6-11

    Once per month grease the Pipe Rack Ball sockets.

    Figure 59: Pipe Rack, Ball Socket, Grease Points. Once per month grease the Pipe Rack Hydraulic Leg cylinder. Every year remove the Foot of the Pipe Rack Hydraulic Leg, clean the Socket and Ball,

    grease and re-assemble.

    Figure 60: Hydraulic Leg, Grease Point.

    GREASE POINTS

    GREASE POINT

    FOOT SOCKET AND

    BALL

  • Canrig Automated Power Catwalk Model 3000

    6-12 Revision April 2011

    Every 6 months grease the electric motor bearings. Four shots per bearing are sufficient.

    Figure 61: Electric Motor, Grease Points. Hydraulic Filters & Oil Check the in-tank oil filter gauge, mounted on the reservoir top, monthly and change the

    filter element when the gauge indicates greater than 20 PSI during carrier lifting or lowering or when the high filter pressure error displays on the operator interface display. Note: Disregard the high filter pressure error when the oil is cold (less than 70F (21C) ).

    Replace the Pump Case Drain Spin-On filter whenever the in-tank return filter requires

    replacing, Figure 17, or every 6 months whichever occurs first.

    Check the high-pressure filter indicator monthly and change the filter element when the indicator shows in the red while the Carrier is lifting or lowering.

    GREASE POINTS

  • Section 6: Maintenance

    Revision April 2011 6-13

    Hydraulic Oil High quality hydraulic oil is essential for satisfactory performance and long hydraulic system component life. Oil having 150 to 330 SUS viscosity at 100F (38C) and viscosity index of 100 or greater will give good results under normal temperature conditions. The use of oil having a high viscosity index will minimize cold-start trouble and reduce the length of warm-up periods. A high viscosity index will minimize changes in viscosity with corresponding changes in temperature. Maximum cold weather start-up viscosity should not exceed 5000 SUS with a pour point at least 20F lower than the minimum ambient temperature. Under continuous operating conditions the temperature of the oil at any point in the system must not exceed 180F. 120-140F is generally considered optimum. Anti-wear type hydraulic oils are recommended. These oils are generally developed and evaluated on the basis of pump wear tests such as ASTM-D2882. These oils offer superior protection against pump and motor wear. They also provide good demulsibility as well as protection against rust.

    Hydraulic Oil General Recommendations

    Ambient Temperature (C) ISO Grade of Oil

    -45 to 15 15 -20 to 15 22 10 to 35 32 20 to 45 46 25 to 55 68

  • Canrig Automated Power Catwalk Model 3000

    6-14 Revision April 2011

    Skate Cable Maintenance Check Skate cable tension once per month and adjust if necessary. To check tension, move the skate to the rear of the Carrier, lift the Carrier up the ramp part way so that the under side of the Carrier can be inspected. Install the safety stop bar. Slowly run the Skate forwards while watching the cable. The cable will momentarily become slack as the cable wraps on the Skate Winch Drum move across the drum from one side to the other. At its lowest point, the cable should not hang more than 4 inches below the underside of the Carrier frame. Tighten the cable by removing the locking plate at the rear of the Carrier and then equally threading in the cable tensioner bolts. Do not over tighten the cable. Every month add a small amount of hydraulic oil to the Skate Cable while a second operator is moving the skate repeatedly to each end of its travel.

    Figure 62: Skate Cable Tensioner.

    Ensure all personnel are clear of any moving parts to prevent

    accidental injury or death.

    LOCKING PLATE

    TENSIONER BOLTS

    NOTE Always move the skate forward then backward (or visa versa) for a minimum of 15 feet. NEVER tighten the cable so much that you do not see a momentary drop in the cable when reversing the skate travel.

  • Section 6: Maintenance

    Revision April 2011 6-15

    CARRIER WINCH MAINTENANCE Lubrication The following table gives the recommended viscosity in relation to ambient temperature. Other brand products may be acceptable, be certain that your lubricant supplier provides oil

    That is equivalent to those shown here. Note: cSt is the same as mm2/s. For special conditions consult Canrig for recommendations. The recommended working temperature of the sump should be between 50 and 70C (122 to 158F). The intermittent peak temperature of the sump should be no greater than 95C (203F). The winch is filled via the filler plug. Fill with gear oil until it reaches the oil level gage / port. Refer to manufacturers literature for more information.

    DO NOT OVERFILL as this may cause the winch to overheat. DO NOT work under the raised Carrier without the Safety

    Stop bar installed.

    Do not operate or perform any lubrication, maintenance or repair on this product, until you have read and understood the operation, lubrication, maintenance and repair information.

    Ambient Temperature

  • Canrig Automated Power Catwalk Model 3000

    6-16 Revision April 2011

    Changing Oil

    Using the correct type and viscosity of lubricating oil is critical to

    the proper function of this winch. The sprag clutch is particularly sensitive to EP (extreme pressure) additives.

    Failure to use the correct type and viscosity of oil may cause

    failure of the winch to hold the load and result in property damage, personal injury or death.

    Procedure for Changing Oil

    1. Before changing oil, consider taking an oil sample for analysis. 2. Run the winch to warm up oil and to ensure particles are suspended in the oil. 3. Place an oil pan or bucket beneath the drain port to collect the oil. 4. To allow oil to drain from the winch, loosen and remove the plug. 5. Rotate drum to fill position. 6. Fill with the correct oil to the correct level. Correct oil level is indicated when the oil

    begins to run out of the plug at the 9-Oclock position. 7. Replace and tighten the drain plug. 8. Operate the winch for 30 seconds. 9. Stop the winch for 30 seconds then re-check for correct oil level. 10. Check that fittings and plugs are correctly tightened. 11. Dispose of used oil and clean up any spillage in an environmentally sound way.

    Hot oil and components can cause personal injury. Do not allow hot oil or components to contact skin.

    Winch Usage Category

    Hours usage per month based on the average usage over a 3 month period

    Oil Change Requirement

    Infrequent Usage less than 10 hours Annual (every 12 months)

    Moderate Usage 10-50 hours Annual (every 12 months)

    Heavy Usage 50-200 hours Semi-annual (every 6 months)

    Severe Usage Operated at loads over 75% of rated load for more than 75% of lifts. And/or over 200 hours per month Quarterly (every 3 months)

  • Section 6: Maintenance

    Revision April 2011 6-17

    Vent Cleaning The vent fitting is located on the motor end of the winch. It is very important to keep this vent clean and unobstructed. Whenever gear oil is changed, remove vent fitting, clean with solvent and reinstall. Do not paint over the vent and do not replace with a plug.

    Figure 63: Carrier Lift Winch (Lantec), Vent Plug & Mounting Bolts

    MOUNTING BOLTS

    VENT PLUG

  • Canrig Automated Power Catwalk Model 3000

    6-18 Revision April 2011

    Mounting Bolts The recommended torque for the Winch mounting bolts is 600 ft. lbs., Figure 54. Tighten all winch base mounting bolts to recommended torque after the first one hundred (100) hours of operation, then every 1000 operating hours or six (6) months, whichever occurs first. Tighten all Winch Cable Clamp bolts to recommended torque after the first one hundred (100) hours of operation, then every 1000 operating hours or six (6) months, whichever occurs first, The recommended torque for the Winch Cable Clamp bolts is 110 ft. lbs., Figure 55.

    Figure 64: Carrier Lift Winch (Lantec) Drum Bearing Adjustment Outboard Bearing Group 405255 requires endplay adjustment. Check endplay every 1000 operating hours or six (6) months, whichever occurs first. Tighten the adjusting nut to remove all endplay in the bearings, then loosen the adjusting nut turn. This will give the required 0.020-0.030 bearing endplay. See Component Literature.

    CABLE CLAMP BOLTS 6 PLACES

    DRAIN PLUG

    LEVEL PLUG

  • Section 6: Maintenance

    Revision April 2011 6-19

    INSPECTION

    Automated Power Catwalk Model 3000 1000 Day Inspection Rig #: Date: Location: Running Hours:

    Inspect the following after the 30 Point Inspection and look for any sign of wear or damage.

    CATWALK BASE * Inspection 5/4 Comments Skid Rollends MPI Ramp Pivot Posts MPI Pipe Rack Arm Mounts/Hitch Blocks MPI Pipe Indexers Mount Plates Visual Pipe Rack Arms Visual RAMP * Ramp Pivot Posts MPI Carrier Roller Guide Channels Visual Ramp Sheave Support Plates Visual Ramp Sheaves Visual Winch Mounts MPI Wich Protective Guard Visual CARRIER * Carrier Cable Connections MPI Cable Block Welds MPI Carrier Pipe Kickers MPI Carrier Overshoot Dogs Visual Front Carrier Roller Shaft Welds Visual Lift Arm Pivot Bushing Block Visual LIFT ARM* Lift Arm Pin Mounts MPI Lift Arm Welds Visual Hydraulic Power System Hydraulic Fluid Level (3/4 Full) Visual Hydraulic Winch Oil Level Visual Periodic Hydraulic Oil Analysis Visual Periodic Hydraulic Winch Oil Analysis Visual Hydraulic Pump Visual Valve Bank Visual Hydraulic Cylinders Visual No Oil Leakage in the system Visual Electrical System -Lockout and Taggout when inspecting the boxes Grounding Visual Wires, Boxes and Connectors Visual Electrical Motor Visual Lights and Proximity Switches Visual Radio Control Unit Visual PLC Box Visual Electrical Control Box Visual Notes:

    Completed By: Signature:

  • Canrig Automated Power Catwalk Model 3000

    6-20 Revision April 2011

    Inspection Indication Map

    Part Name: Skid Rollend The following information should be supplied on the inspection Report as minimum: Purchase Order # Date: Inspection Report # Canrig Part # Inspectors Signature/Stamp: Power Catwalk S/N: Type of Inspection: Canrig Representative:

    Procedure: Perform Dry Magnetic Particle Inspection on all welds shown in accordance with ASTM E709. Acceptance criteria are as defined in ASTM E709. All other areas not indicated shall be visually examined for damage and signs of fatigue.

  • Section 6: Maintenance

    Revision April 2011 6-21

    Part Name: Skid Ramp Pivot Post The following information should be supplied on the inspection Report as minimum: Purchase Order # Date: Inspection Report # Canrig Part # Inspectors Signature/Stamp: Power Catwalk S/N: Type of Inspection: Canrig Representative:

    Procedure: Perform Dry Magnetic Particle Inspection on all welds shown in accordance with ASTM E709. Acceptance criteria are as defined in ASTM E709. All other areas not indicated shall be visually examined for damage and signs of fatigue.

  • Canrig Automated Power Catwalk Model 3000

    6-22 Revision April 2011

    Part Name: Pipe Rack Arm Mount/Hitch Block The following information should be supplied on the inspection Report as minimum: Purchase Order # Date: Inspection Report # Canrig Part # Inspectors Signature/Stamp: Power Catwalk S/N: Type of Inspection: Canrig Representative:

    Procedure: Perform Dry Magnetic Particle Inspection on all welds shown in accordance with ASTM E709. Acceptance criteria are as defined in ASTM E709. All other areas not indicated shall be visually examined for damage and signs of fatigue.

    42 Catwalk Shown 26 Only has one Hitch Block

  • Section 6: Maintenance

    Revision April 2011 6-23

    Part Name: Ramp Pivot Post The following information should be supplied on the inspection Report as minimum: Purchase Order # Date: Inspection Report # Canrig Part # Inspectors Signature/Stamp: Power Catwalk S/N: Type of Inspection: Canrig Representative:

    Procedure: Perform Dry Magnetic Particle Inspection on all welds shown in accordance with ASTM E709. Acceptance criteria are as defined in ASTM E709. All other areas not indicated shall be visually examined for damage and signs of fatigue.

  • Canrig Automated Power Catwalk Model 3000

    6-24 Revision April 2011

    Part Name: Ramp Winch Mount

    The following information should be supplied on the inspection Report as minimum: Purchase Order # Date: Inspection Report # Canrig Part # Inspectors Signature/Stamp: Power Catwalk S/N: Type of Inspection: Canrig Representative:

    Procedure: Perform Dry Magnetic Particle Inspection on all welds shown in accordance with ASTM E709. Acceptance criteria are as defined in ASTM E709. All other areas not indicated shall be visually examined for damage and signs of fatigue.

  • Section 6: Maintenance

    Revision April 2011 6-25

    Part Name: Carrier Cable Block and Connections The following information should be supplied on the inspection Report as minimum: Purchase Order # Date: Inspection Report # Canrig Part # Inspectors Signature/Stamp: Power Catwalk S/N: Type of Inspection: Canrig Representative:

    Procedure: Perform Dry Magnetic Particle Inspection on all welds shown in accordance with ASTM E709. Acceptance criteria are as defined in ASTM E709. All other areas not indicated shall be visually examined for damage and signs of fatigue.

    Typical on both sides

    Inspect the one connected to the

  • Canrig Automated Power Catwalk Model 3000

    6-26 Revision April 2011

    Part Name: Carrier Pipe Kicker Mount The following information should be supplied on the inspection Report as minimum: Purchase Order # Date: Inspection Report # Canrig Part # Inspectors Signature/Stamp: Power Catwalk S/N: Type of Inspection: Canrig Representative:

    Procedure: Perform Dry Magnetic Particle Inspection on all welds shown in accordance with ASTM E709. Acceptance criteria are as defined in ASTM E709. All other areas not indicated shall be visually examined for damage and signs of fatigue.

    See Product Bulletin 10

  • Section 6: Maintenance

    Revision April 2011 6-27

    Part Name: Lift Arm Pin Mounts The following information should be supplied on the inspection Report as minimum: Purchase Order # Date: Inspection Report # Canrig Part # Inspectors Signature/Stamp: Power Catwalk S/N: Type of Inspection: Canrig Representative:

    Procedure: Perform Dry Magnetic Particle Inspection on all welds shown in accordance with ASTM E709. Acceptance criteria are as defined in ASTM E709. All other areas not indicated shall be visually examined for damage and signs of fatigue.

  • Canrig Automated Power Catwalk Model 3000

    6-28 Revision April 2011

    Troubleshooting Flow