Canon Resetter ERROR DISPLAY

Errors are displayed by the LEDs, and ink low warnings are displayed by the Status Monitor.3-1. Operator Call Error (Alarm LED Blinking in Orange)

Alarm LEDblinking Error Corrective action2 times No paper Set paper, and press the Resume/Cancel button to feed the paper.3 times Paper jam Remove the jammed paper, and press the Resume/Cancel button.4 times No ink Replace the ink cartridge(s), or press the Resume/Cancel button to continue printingwithout replacing the ink cartridge(s).5 times The ink cartridges are not properly installed, or a non-supported ink cartridge is installed(the ink cartridge EEPROM data is abnormal).Install the ink cartridges properly.Or, confirm that the supported ink cartridges areinstalled.7 times Ink cartridge not installed Install the ink cartridge(s), and close the access cover.8 times Waste ink absorber full or platen waste ink absorber full warning (approx. 95% of the maximum capacity)Pressing the Resume/Cancel button will exit theerror, and enable printing.14 times Non-supported ink cartridge installed Replace the non-supported ink cartridge with thesupported one.16 times Used ink cartridge installed, or no ink Pressing the Resume/Cancel button will exit the error, and enable printing.

Carriage error or Error Code 5100Condition: An error occurred in the carriage encoder signal.Problems and Solutions: Smearing or scratches on the carriage slit film- clean the timing slit film. Foreign material or paper debris that obstructs the carriage movement;- remove foreign material. Ink tank conditions;- re-seat the ink tanks. If other solution fail, replace one off the following- Timing slit disk film- Carriage unit- Logic board- Carriage motor Line Feed error or Error Code 6000Condition: An error occurred in the LF encoder signal.Problems and Solutions: Smearing or scratches on the LF / EJ slit film- clean the LF / EJ slit film. Foreign material or paper debris in the LF drive;- remove foreign material. If other solution fail, replace one off the following- LF / EJ slit film- LF / EJ timing sensor unit- Paper feed roller unit- Logic board- Paper feed motorPurge cam sensor error or Error Code 5C00Condition: An error occurred in the purge unit.Problems and Solutions: Foreign material or paper debris around the purge drive system unit;- remove foreign material. If other solution fail, replace one off the following- Purge drive system unit- Logic boardASF sensor error or Error Code 5700Condition: An error occurred in the ASF cam sensor.Problems and Solutions: Replace one of the following:- ASF unit- PE sensor board unit- Logic boardInternal temperature error or Error Code 5400Condition: The internal temperature is not normal.Problems and Solutions: Replace one of the following:- Carriage unit- Logic board- Print headInk absorber is full or Error Code 5B00, 5B01Condition: The ink absorber is supposed to be full. Message on the Monitor screen or printer LCD: Ink absorber full. Service required.Problems and Solutions: Ink absorber is full or waste pad inside the printer is almost full- Replace printer's Ink absorber pad and reset the ink absorber counter value in the EEPROM. Click here for your printer model reset procedure and service toolsPrint head temperature rise error or Error Code 5200Condition: The print head temperature exceeded the specified value.Problems and Solutions: Turn off the printer and then turn on if error still persist replace Ink cartridge or print head EEPROM error or Error Code 6800, 6801Condition: A problem occurred in reading from or writing to the EEPROM.Problems and Solutions: Replace logic boardVH monitor error or Error Code B200Condition: The print head voltage is abnormal.Problems and Solutions: Replace Print head and logic board (Replace them at the same time.) Replace Power supply unit Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFCCarriage lift mechanism error or Error Code 5110Condition: The carriage did not move up or down properly.Problems and Solutions: Foreign material or paper debris that obstructs the carriage movement- remove foreign material. Consider replacing:- Switch system unit- Carriage unitAPP position error or Error Code 6A80Condition: An error occurred in the APP motor.Problems and Solutions: Check for foreign material or paper debris around the purge drive system unit- remove foreign material. Check for foreign material or paper debris around the ASF unit- remove foreign material. If other solution fail, replace one off the following part- Purge drive system unit- Logic boardAPP sensor error or Error Code 6A90Condition: An error occurred during paper feeding or purging.Problems and Solutions: check for foreign material or paper debris around the purge drive system unit;- remove foreign material. check for foreign material or paper debris around the ASF unit;- remove foreign material. If other solution fail, replace one off the following part- Purge drive system unit- Logic boardPaper feed cam sensor error or Error Code 6B10Condition: An error occurred in the paper feed cam sensor during paper feeding from the cassette, or the paper absorbing a large amount of ink jammed in the PF rear guide.Problems and Solutions: Jammed paper in the PF rear guide (when a large amount of ink was absorbed in the paper);- remove the jammed paper and foreign material. check for foreign material or paper debris in the cassette or in the PF rear guide;- remove foreign material. If other solution fail, replace one off the following part- PF pick-up unit- Logic boardUSB Host VBUS overcurrent or Error Code 9000Condition: The USB Host VBUS is overloaded.Problems and Solutions: Replace Logic boardPump roller sensor error or Error Code 5C20Condition: The pump roller position cannot be detected.Problems and Solutions: Replace Purge drive system unitInk tank position sensor error or Error Code 6502Condition: None of the ink tank position is detected.Problems and Solutions: check Ink tank position Re-seat or replacement of ink tanks Replace parts- Spur unit- Logic boardFlatbed motor error or Error Code 5012Condition: An error occurred in the scanner flatbed motor.Problems and Solutions: replace Scanner unitValve cam sensor error or Error Code 6C10Condition: The valve cam sensor was faulty at power-on or when purging was attempted.Problems and Solutions: check for foreign material or paper debris around the purge drive system unit;- remove foreign material. Replace- Purge drive system unit- Logic board

This is for Old Canon Printer Error Code (MP198, MP145, MP160, Etc)

E2-2 = No paper (ASF)E3-3 = Paper jamE4 = No inkE5-5 =The ink cartridges are not installed or a non-supported ink cartridge is installed,or the ink cartridges are not installed properlyE8 = Waste ink absorber full, or platen waste ink absorber fullE9 =The connected digital camera / video camera does not support Camera direct PrintingE14 =The Ink cartridges whose destination are wrongE15 =Ink cartridge is not installedE16 =Ink remaining is unknownE16-E19 = Failed to scan head alignment sheetE22 =Carriage errorE23 =Paper feed errorE24 =Purge unit errorE25 =ASF(cam) sensor errorE26 =Internal temperature rise errorE27 =Waste ink absorber full or platen waste ink absorber fullE28 =Ink cartridge temperature rise errorE29 =EEPROM errorE33 =Paper feed position errorE35 15 =USB Host VBUD overcurrent error - USBE37 17 =Abnormal motor driver error

CANON MX318

If you encounter a problem or an error like "Ink absorber is full" or Error Code 27 or "Error Code 5B00". Its mean that the Printer Counter Protection is Full and it required a reset and Ink wastepad replacement, if you want your printer to work again. There are two ways to reset the Canon MP (all in one) printer, One is by using a Software tool and the other is manually resetting the EEPROM of the printer. Below is the step by step procedure on how to reset your Canon MP (All in One) printer.

Please follow the step by step procedure to reset your Canon Pixma MX318 Printer1. Turn off the Printers.2. Press and Hold the "Stop/Reset" button then press POWER button.3. Release the "Stop/Reset" button while keeping POWER button on press.4. Press "Stop/Reset" 2 times and then release all the buttons. 5. Note: If the above was properly performed the printer will enter the "Service Mode".6. Press the "Stop/Reset" button 4 times, this will select the clear waste ink counter function. The lamp will alternate (change) color with each key press.Mode:1. Service/Factory test printout, including ink sensor check.2. EEPROM - Info printout.3. EEPROM - Initialization.4. Reset the Waste ink counter.7. After selecting the desired mode (eg 4), press the POWER button to "set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer. Or unplug the printer to turn off.8. On the Canon Pixma MX318 Printers, And your done!Warning: Getting rid of the error message wont change that you might end up with ink leaking out of the printer if you dont either replace or clean the ink wastepad.

CANON MP Series

If you encounter a problem or an error like "Ink absorber is full" or Error Code 27 or "Error Code 5B00". Its mean that the Printer Counter Protection is Full and it required a reset and Ink wastepad replacement, if you want your printer to work again. There are two ways to reset the Canon MP (all in one) printer, One is by using a Software tool and the other is manually resetting the EEPROM of the printer. Below is the step by step procedure on how to reset your Canon MP (All in One) printer.

This procedure and resetter also work fine on following canon printer models:Canon MP150, Canon MP160, Canon MP170, Canon MP180, Canon MP450 and Canon MP460 printer.

Method One: Using Mptool Software to reset Canon MP Printer1. Turn of printer then run mptool software this software automatically detect the printer.2. Click reset main and reset platen button in the waste ink counter section.3. If you want to reset the cartridge ink level, click reset black and reset color in the ink counter section. Method Two: Reset manual Canon Pixma MP Printers1. Turn off the Printers.2. Press and Hold the button Resume/Cancel then press POWER button.3. Release the Resume/Cancel button while keeping POWER button on press.4. Press Resume/Cancel 2 times and then release all the buttons.5. When the indicator recorded GREEN - click Resume/Cancel 4 times!6. Turn off and On the Canon Pixma MP Printers. And your done.Warning: Getting rid of the error message wont change that you might end up with ink leaking out of the printer if you dont either replace or clean the ink wastepad. Canon Pixma Mp258 Error Code and Possible Solution

P02 (Carriage error)1. Make sure no foreign material stuck to the print head railway.2. Clean and check the print head encoder strip cable (timing slit film or encoder strip is a white line on the back of the box set of ink lines may be missing or mess up the ink.P03 (Line feed error): an error in transmission line entering the line feed (LF) is a signal telling the printer to move to another line or a whole new line that would not otherwise have reached the end of the line.1. Check wire print head position (timing slit disk film) on the side of the machine.2. Check PCB logic board.P05 (ASF sensor error) sensor for paper feed error. 1. Try to replace the following: ASF / PE sensor unit. Drive unit. PCB logic board.P06 (Internal temperature error): caused by abnormal heat inside the printer.

P07 (Ink absorber full): the Ink Wastepad (sponge) inside the printer is full1. Replace the wastepad inside the printer or install waste ink bin outside the printer2. then Reset counter protection.P08 (Print head temperature rise error): caused by thermal print head temperature exceeds a threshold.1. Replace the new cartridge print head and / or change a new logic board.P09 (EEPROM error): caused by corrupted or defective EEPROM chips of the printer.1. Replace the logic board.P15 (USB VBUS over current): caused by too much current, try removing the USB cable and then plugin again, if solve the error, try to replace with a new USB cable. If the error still exist replace the logic board.

P20 (Other hardware error): The failure of other hardware.1. Try to replace the logic board.P22 (Scanner error): a scanner malfunction.1. try to change the scanner unit or change a the logic board.E13 or E16: Ink has run out

1. Pressing the Stop / Reset button for 5 to 8 seconds until the led screen display number 1.

E04, E05, E14 or E15: Cartridge may not be installed properly1. Reinstall the ink cartridge.

CANON IP2770

1. Canon PIXMA iP2770 are classified into photo printers. This printer is very suitable for use at home. Results in getting the equivalent of lab quality photos. The speed of this printer quickly spelled out that is about 7 ipm for mono and the 4.8 ipm for color and for 4R-sized photo takes 55 seconds. Resolution of Canon PIXMA iP2770 printer at 4800 x 1200dpi (max). Still uses USB 2.0 connectivity and the type cartridge using PG-810, CL-811 (PG-810XL, CL811XL Optional). For this printer weight of 3.4 kg with dimensions of 445 X 250 X 130mm.

If a lights blink on thePOWERandRESUMEbutton alternately and it will show an error5B00. It means that your ink absorber inside the printer is almost full. In order to solve this you need to clear or reset the counter protection of your printer. To do this, follow this steps.

First make sure that the power cable and usb cable are connected, before you perform the reset procedure. And download the resetter at the bottom of this post.

FIRST STEPS: Entering Service ModeYou have to enter in service mode in order to used the resetter. To do that follow this procedure,

1. Turn off the printer without pulling the power cords.2. Hold down Resume button and press Power button.3. Keep holding down Power button and let Resume button go.4. Then Press Resume button 5 times then let BOTH buttons go.5. You will notice that the Alternate Blinking error is gone, this means that the printer is in Service Mode state.

SECOND STEPS:Using the Resetter

1. After you download the resetter, extract it and double click "servicetool.exe"2. Press the "Main" Button, Then press "EEPROM Clear" button if a pop-up appear just click OK5. Then power off the printer(sometimes you have to press twice the power button to turn off) and turn on again. and its done!Warning:Getting rid of the error message wont change that you might end up with ink leaking out of the printer if you dont either replace or clean the ink wastepad.DownloadhereCANON IP1980 & IP 1880

When you try to print and a pop-up message appear saying that "The ink absorber is full" it means that the ink absorber or wastepad inside your printer is almost full. In order to solve this you need a technical knowledge on how to disassemble the printer and software resetter.

FIRST STEPS: Entering Service Mode

First you have to enter in service mode state in order to used the resetter. To do that follow this procedure,1. Unplug the power cable of the printer.2. Press and hold down the power button with your index finger and then plug-in the power cable.3. While holding down the power button, press the reset/resume button twice and release the power button4. You will notice that the Alternate Blinking error is gone, this means that the printer is in Service Mode state.5. Using Canon ResetterDownloadCanon ip1980 hereCanon ip1880 here

SECOND STEPS: Using the Software

1. After you download the resetter, extract it and double click "GeneralTool" 2. Select or Check the EEPROM CLEAR then click the MAIN button, you will notice that the power button light will blink. It means that the it clear the waste ink counter.

3. Unplug the power cable to turn off the printer4. Then plug-in again the power cable. then turn ON the printer. And its DONE!Warning: Getting rid of the error message wont change that you might end up with ink leaking out of the printer if you dont either replace or clean them.

Email ThisBlogThis!Share to TwitterShare to FacebookShare to Pinterest