calibre wiring guide
TRANSCRIPT
GROUND#8 X 1/2" TEK
IGNITIONSWITCHED+12 VOLTS
BLACKRED
BROWN
BLUE
GRAYWHITE
GR
AY
GR
AY
WH
ITE
BL
UE
INTERIOR NETWORK MODULE
FRONTRADAR
LED
REARRADAR
LED(CALIBRE DL
model only)
RECEIVERCABLE
FRONT
AMPLIFIED SPEAKER
REAR LASER DEFUSER(OPTIONAL)
+12 VOLT BATTERY
OR IGNITION SOURCE
BLUE
YELLOW*
BROWN*
BLACK
BLACKCABLE
FUSECONNECTION
GROUND#8 X 1/2" TEK
1AMP
YELLOW*
BROWN*
BLACK
FRONT LASER DEFUSER(OPTIONAL)
+12 VOLT BATTERY
OR IGNITION SOURCE
YELLOW*
BROWN*
WHITE
BLACK
BLACKCABLE
FUSECONNECTION
1AMP
GROUND#8 X 1/2" TEK
YELLOW*
BROWN*
BLACK
RECEIVERCABLE
REAR
BLOCK DIAGRAM
*THE YELLOW AND BROWNRADAR RECEIVER WIRESARE USED TO CONNECT TOTHE OPTIONAL LASERDEFUSER. IF NO LASERDEFUSER IS BEINGINSTALLED WITH THERADAR RECEIVER (FRONTAND/OR REAR), THE YEL-LOW AND BROWN WIRESWILL NOT BE USED.
CALIBRE
44586-2 07/07
IGNITION AND GROUND1. Use a test meter to locate an ignition on source for the Interior Network Module with +12 volts when
ignition key is both on and cranking.
2. Connect the black wire to a solid chassis ground using the provided ring terminal and silver self-tapping screw.
3. Radar receivers may be connected to either a +12 volt ignition on source or +12 volt constant battery source.
*NOTE: THE RED WIRESHOULD BE CONNECTED TO A MINIMUM 16 GAUGE+12 VOLT IGNITION WIRE.
GROUND#8 X 1/2" TEK
IGNITIONSWITCHED+12 VOLTS
BLACKRED
BROWN
BLUE
GRAYWHITE
GR
AY
GR
AY
WH
ITE
BL
UE
INTERIOR NETWORK MODULE
FRONTRADAR
pod
REARRADAR
pod(CALIBRE DL-P
model only)
FRONT LASER DEFUSER
RECEIVERCABLE
(OPTIONAL)
AMPLIFIED SPEAKER
REAR LASER DEFUSER(OPTIONAL)
+12 VOLT BATTERY
OR IGNITION SOURCE
BLUE
YELLOW*
BROWN*
BLACK
BLACKCABLE
FUSECONNECTION
GROUND#8 X 1/2" TEK
1AMP
YELLOW*
BROWN*
BLACK
+12 VOLT BATTERY
OR IGNITION SOURCE
YELLOW*
BROWN*
WHITE
BLACK
BLACKCABLE
FUSECONNECTION
1AMP
GROUND#8 X 1/2" TEK
YELLOW*
BROWN*
BLACK
FRONT
RECEIVERCABLE
REAR
BLOCK DIAGRAM
IGNITION AND GROUND1. Use a test meter to locate an ignition on source for the Interior Network Module with +12 volts when
ignition key is both on and cranking.
2. Connect the black wire to a solid chassis ground using the provided ring terminal and silver self-tapping screw.
3. Radar receivers may be connected to either a +12 volt ignition on source or +12 volt constant battery source.
*THE YELLOW AND BROWNRADAR RECEIVER WIRESARE USED TO CONNECTTO THE OPTIONAL LASERDEFUSER(S). IF A LASERDEFUSER IS NOT BEINGINSTALLED WITH A RADARRECEIVER (FRONT AND/ORREAR), THE YELLOW ANDBROWN WIRES WILL NOT BE USED.
CALIBRE*NOTE: THE RED WIRESHOULD BE CONNECTED TO A MINIMUM 16 GAUGE+12 VOLT IGNITION WIRE.