cable repair(short)
TRANSCRIPT
-
8/12/2019 Cable Repair(Short)
1/16
CREATING A 568A, 568B,OR CROSSOVER CABLE
Creator:Dennis Groseclose
-
8/12/2019 Cable Repair(Short)
2/16
RJ-45 Color Codes
Brown Not used8White & Brown Not used7 Orange Receive -6
White & Blue Not used5Blue Not used4White & Orange Receive +3Green Transmit -2White & Green Transmit +1ColorUsePin #
-
8/12/2019 Cable Repair(Short)
3/16
-
8/12/2019 Cable Repair(Short)
4/16
REPAIR TECHNIQUES
The Steps to Rebuilding a CAT 5 Cable
1. Inspect the cable and determine the problem
2. Cut off the damaged section
3. Cut away the sheathing
4. Separate the pairs by colors
5. Align the wires in the proper pattern
6. Hold the wires in place between thumb and forefinger7. Cut the wires evenly across
8. Push the wires into the RJ45
9. Inspect the clip to make sure the wires are fully inserted
10. Crimp and Test
-
8/12/2019 Cable Repair(Short)
5/16
REQUIRED TOOLS
Crimp Tool
Punch-Down Tool
-
8/12/2019 Cable Repair(Short)
6/16
INSPECT THE CABLE
Look at the cable fordefects. What you willusually see withcables undergoingmany insertions willbe a broken top clip.This will prevent thecable from remaining
secured in the jack.
-
8/12/2019 Cable Repair(Short)
7/16
Cut Off the Unwanted Section
-
8/12/2019 Cable Repair(Short)
8/16
Cut the Sheathing Back About One Inch
Very carefully cut the blue sheathing back about 0ne
inch. Be careful not to cut into the inside wires.The sheathing can usually be twisted off if the cut
does not separate the pieces. This is actuallypreferable to cutting too deeply and cutting thewires.
-
8/12/2019 Cable Repair(Short)
9/16
Separate The Wires by Pairs
There are fourpairs in the cable.Separate each pairwithout separatingthe individualwires.
-
8/12/2019 Cable Repair(Short)
10/16
-
8/12/2019 Cable Repair(Short)
11/16
THE 568-B PATTERN
Align the wiresinto the 568Bpattern.
Orange- WhiteOrange
Green- White
Blue
Blue-WhiteGreen
Brown-White
Brown
8-BR7-BRW
6-GR5-BLW
4-BL 3-GW
2-O1-OW
-
8/12/2019 Cable Repair(Short)
12/16
Firmly Grip Wires
Hold the wires firmly between the
thumb and forefinger, maintainingthe proper pattern.
-
8/12/2019 Cable Repair(Short)
13/16
Cut The Wires Evenly
Cut the wiresevenly across alleight wiressimultaneouslywhile maintaininga firm grip, do notrelease the wires.The cut shouldleave about 3/4 ofan inch of wireexposed.
-
8/12/2019 Cable Repair(Short)
14/16
Insertion into the RJ45Maintain the firm grip on
the wires and slowly easethe array of wires into theRJ45 clip.The clip partshould be on top and the#1 wire should be on theleft.( Front reference )
Closely observe to makecertain all wires are beingpushed completely to thefront of the clip, no wires
are crossed, and thecorrect pattern isinstalled.
#1Wire
TOP of CLIP
FRONT
-
8/12/2019 Cable Repair(Short)
15/16
-
8/12/2019 Cable Repair(Short)
16/16
Crimp the RJ45
Hold the cable andRJ45 while insertingthe clip into a
crimping tool. Use astrong and measuredsqueeze to makecertain the pins areall pushed down into
the wires. Failure topush the connectorsall the way into thewires will result in adefective cable.