by charles braing4guo [email protected]
DESCRIPTION
2012 BATC CONVENTION. DATV-Express. by Charles BrainG4GUO [email protected]. DATV-Express. The main DATV-Express team members. Ken Konechy - W6HHCPGM Manager Art Towslee- WA8RMCHardware Tom Gould- WB6PPCB Layout Charles Brain- G4GUOSoftware. 2. DATV-Express. - PowerPoint PPT PresentationTRANSCRIPT
2
DATV-Express
The main DATV-Express team members
• Ken Konechy - W6HHC PGM Manager• Art Towslee - WA8RMC Hardware• Tom Gould - WB6P PCB Layout• Charles Brain - G4GUO Software
3
DATV-Express
Goals of the Project
• Significantly reduce the price of Digital-ATV transmitters• Provide an open platform for future DATV development• Help educate the community and ourselves about new technologies.• Get more DATV stations on-air • Encourage more people to get licensed• By product will be a Software Defined Transmitter for the 23 cms band with a B/W of up to 8 MHz.
4
DATV-Express
It all started when I bought a USRP2
5
DATV-Express
Overview of DATV-Express System
System Block Diagram for DATV-Express DATV Transmitter
6
DATV-ExpressOverview of Hardware Board USB2 Interface Cypress CY7C68013A• FPGA Altera EP2C8T144CN• DAC Analogue Devices AD9767ASTZ• Clocks• PLL/modulator for 1.3 GHz ADRF6750A• Buffer amplifier GVA-84+ ~20 mW• Optional symbol rate generator Si570• DC-DC power supplies allows single 12V input
7
DATV-ExpressOverview of Hardware Board – cont’d
Block Diagram for DATV-Express Hardware Board
8
DATV-Express
First prototype
9
DATV-Express
Overview of PC Software
• Operating System - Linux 32/64-bit then Win32• Loads FX2 firmware (Control Transfer)• Loads FPGA firmware (EP1)• Controls 1.3 GHz PLL (EP1)• Controls symbol rate generator (EP1)• I/Q offset calibration (EP1)• Provides GUI
10
DATV-ExpressOverview of PC Software – cont’d
• Take program/transport stream from capture device• Converts to a transport stream with correct PIDS• Adds SI Table information• Adds FEC • Does interleaving• Keeps symbol rate constant, no overruns or under runs by adding Null transport packets• Generates either IQ symbols or a bitstream• Talks to exciter board via USB interface (EP2)
DATV-ExpressGUI Screen-shot (current)
12
DATV-ExpressOverview of Hardware Board SoftwareFX2 code (USB chip has 8051) C/ASM• Programs FPGA• Manages USB FIFO interface with FPGA• I2C interface with 1.3 GHz PLL• I2C interface with symbol rate generator• I2C interface to FPGA • General Housekeeping
FPGA code, Verilog, Altera Quartus II• Interpolates symbols to final sample rate• Channel filter• Writes to DAC
13
DATV-ExpressDATV-Express Minimum System Specs• DVB-S protocol• QPSK modulation (will allow other modulations)• Frequency Range: 950–1575 MHz (allowed by ADRF6750 chip)
– 1240–1300 MHz (allowed in USA)– 1240–1325 MHz (allowed in Europe)
• Symbol-Rate:– Adjustable: 1 MSymb/sec -to- 5 MSymb/sec
• Forward Error Correction is selectable• RF output ~ 20 mW buffered (SMA connector)• Video Capture card allows for NTSC or PAL• Initially designed for one video stream• Operating system – first Linux-32/64 then Win32
14
DATV-ExpressCurrent Project Status
• First prototype PCB built• Linux GUI, DVB-S and DVB-T code working
• Basic FPGA code working
• Version 2 PCB being laid out
15
DATV-ExpressProof-of-Progress – 1st DVB-S Transmission
16
DATV-ExpressDVB-S 1.2 GHz spectrum
17
DATV-ExpressQPSK constellations (with noise)
18
DATV-ExpressDVB-S2 32APSK Constellation
19
DATV-Express6 MHz DVB-T spectrum with I/Q balance problem & filter passband ripple
20
DATV-Express1.3 GHz 7 MHz DVB-T on a PC with a Realtek USB Dongle and DVBDream
21
DATV-ExpressWhat about DVB-T, DVB-S2, 8VSB etc?
• “Yes, they are possible....”• “But, the team is only committed to DVB-S”• We already have experimental support for
Firewire/DV video input, text overlays, testcards, FFMPEG transcoding, 1080i HD and DVB-T.
22
DATV-ExpressWhat about RaspberryPi ?“Yes, it should be possible....”• Pi has hardware H.264 encoding / decoding and will have a
5 Megapixel camera soon. Has USB2 interface. No on board sound in.
• Code needed on Pi to convert raw H.264 data into a valid DVB transport stream and to load FPGA code on Express board. Can probably re-use some code already written.
• Need to wait for Pi foundation to write all the required hardware libraries to support camera.
• Express, will have to move FEC coding to FPGA so board supports transport stream. Only space for DVB-S
DATV-Express
Hope to have final production PCB ready around Christmas time
Intend to provide incremental software releases during the life of the board.
Add DVB-S2 and maybe DVB-T2 Depends on demand but maybe a matching receiver
optimized for < 2 Msymbols/s?
Conclusion and Plans
DATV-Express
Useful Links:
My blog http://www.g4guo.blogspot.co.uk/ Follow me on Twitter @G4GUO
DATV-Express
Thank-you all!