btsmlocaloperation guide huawei
TRANSCRIPT
-
8/16/2019 Btsmlocaloperation Guide Huawei
1/15
T04-01 Login Management
Connecting the Site Maintenance Terminal PC to the BTS
The IP address and the subnet mask of the Site Maintenance Terminal PC are set. The IP
address
of the Site Maintenance Terminal PC and the IP address (192.168.0.72/255.255.255.0) of the
BTS are located in the same network segment.
Procedure
Step 1 Use the ethernet cable to connect the Site Maintenance Terminal PC to the BTS. One
end of the
ethernet cable is connected to the ETH port on the main control module (GTMU for the
DBS3900) of the main cabinet. The other end of the ethernet cable is connected to the
Ethernet cable port on the Site Maintenance Terminal PC (usually a portable PC).
Step 2 Start the command window.
l If the operating system of the Site Maintenance Terminal PC is Windows 98, choose Start
> Program > MS-DOS Prompt. The command window is displayed.
l If the operating system of the Site Maintenance Terminal PC is Windows 2000/XP, choose
Start > Run. In the Run dialog box, run the cmd command. The command window is
displayed.
Step 3 In the command window, run the ping target_name command to verify that the
connection
between the PC and the DBS3900 is established.
NOTE
target_name indicates the IP address of the BTS.
If the messages returned are similar to the following example, the LMT and the BBU
communictae properly. In this example, the IP address of the external network is
192.168.0.72.
Pinging 192.168.0.72 with 32 bytes of data:
Reply from 192.168.0.72: bytes=32 time=1ms TTL=253
Reply from 192.168.0.72: bytes=32 time=1ms TTL=253
Reply from 192.168.0.72: bytes=32 time=1ms TTL=253
Reply from 192.168.0.72: bytes=32 time=1ms TTL=253
Ping statistics for 192.168.0.72:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 1ms, Maximum = 1ms, Average = 1ms
----End
Logging in to the BTS at the Local End
Procedure
Step 1 Start the SMT.
l If the SMT PC communicates with the BTS normally, a window is displayed, as shown in
the following. The SMT is successfully started.
-
8/16/2019 Btsmlocaloperation Guide Huawei
2/15
l If the SMT PC cannot communicate with the BTS, the Communication failed dialog box
is displayed, as shown in the following. Go to Step 2.
Step 2 Click Yes.
The Set Communication Port Parameter dialog box is displayed, as shown:
-
8/16/2019 Btsmlocaloperation Guide Huawei
3/15
Step 3 In the Select Communication Port areas, click Network Port. In the Configure IP area,
set the
IP address to 192.168.0.72.
Step 4 Click OK.
The Site Maintenance Terminal System window is displayed.
Step 5 In the Site Maintenance Terminal System window, click User , and select User Login .
Enter user Name (Omc by default) and User Password (omc by default). Login to the BTS is
successful.
-
8/16/2019 Btsmlocaloperation Guide Huawei
4/15
T04-02 Obtaining the Site Management Rights
Site0→→→→Site Management Right→→→→Get
-
8/16/2019 Btsmlocaloperation Guide Huawei
5/15
T04-03 Board Status Query
Board→→→→Board Management
Double-click GTMU.
Right-click the RRU module to be queried and select Board Information from the shortcut
-
8/16/2019 Btsmlocaloperation Guide Huawei
6/15
menu.
-
8/16/2019 Btsmlocaloperation Guide Huawei
7/15
T04-04 Check the clock synchronization
Board→→→→Board Management
Right-click the GTMU to be queried and select Board Information from the shortcut menu.
-
8/16/2019 Btsmlocaloperation Guide Huawei
8/15
T04-05 Board Extended Information (RRU type information)
Right-click the RRU module to be queried. Select Board Extended Information from the
shortcut menu.
To check the Frequency Band: 900M or 1800M
-
8/16/2019 Btsmlocaloperation Guide Huawei
9/15
T04-06 CPU Usage Monitoring
Site0→→→→View Resource
T04-07 Site Test
Site0→→→→Site Test→→→→Start
-
8/16/2019 Btsmlocaloperation Guide Huawei
10/15
T04-08 Cell Performance Test
Cell0→→→→Cell Performance Test→→→→Start
T04-09 Channel State
BT0→→→→View Channel State
The channel state should be “I” or “A”.
When the state is “O”, it means out of service.
-
8/16/2019 Btsmlocaloperation Guide Huawei
11/15
T04-10 Power Mode
RC0→→→→Get RC Power Mode
-
8/16/2019 Btsmlocaloperation Guide Huawei
12/15
T04-11 Board Reset
If the site is on air, Huawei suggest exempting this test.
Board→→→→Board Management→→→→Right click on the GTMU board →→→→ Board Reset
Board→→→→Board Management→→→→Double-click GTMU→→→→Right-click the RRU module→→→→Reset→→→→
Board
-
8/16/2019 Btsmlocaloperation Guide Huawei
13/15
T04-12 Alarm Query
Board→→→→Board Management→→→→Right-click the GTMU→→→→Board Alarm
Check whether there are major level alarms or critical level alarm.
-
8/16/2019 Btsmlocaloperation Guide Huawei
14/15
Board→→→→Board Management→→→→Double-click GTMU→→→→Right-click the RRU module→→→→Board
alarm
Check whether there are major level alarms or critical level alarm.
-
8/16/2019 Btsmlocaloperation Guide Huawei
15/15