brochure for francesca model -...
TRANSCRIPT
Brochure for Francesca model
Preparing the stove: installation with side discharge
1Remove the micro-connections shown in the illustration
2After removing the left side panel (see points 1 to 5 in section “Access to inspection hatches“), insert the 90° elbow code ecoteck “5700-00-106“
3Remove the side panel, and then the “T“ union with relevant extension
Brochure for Francesca model
Maintenance and cleaning:
Before carrying out any maintenance operation take the following precautions:- Make sure that the general power switch has been disconnected.- Make sure that all the parts of the stove are cold.- Make sure that the ashes have cooled completely.- Always use appropriate tools for maintenance.- When you have finished maintenance reinstall all the safety guards before using the stove again.
The stove requires little maintenance if a quality pellet is used. Therefore it is difficult to establish how often the stove needs to be cleaned. The quality of the pellet and the combustion adjustment are crucial.
Cleaning the combustion chamber:
The stove requires simple but frequent cleaning to guarantee an efficient yield and correct functioning.Therefore, clean the combustion chamber every day using a drum-type vacuum cleaner, making sure that the ashes have gone out completely.
Combustion chamber
Fire pot
Ashes drawer
Cleaning the fire pot:
Clean the fire pot as described in the dedicated chapter of the instruction manual. Only a clean and tidy fire pot can guarantee that the pellet stove will run without any problems. Deposits may form while it is running and these must be eliminated immediately.Correct, daily cleaning will allow the stove to burn properly and to give a good yield, avoiding problems that in the long term could require the intervention of a technician to repair the stove.
Fire pot grill
Scraper
Brochure for Francesca model
Cleaning the ashes drawer:
The ashes drawer must be cleaned every 2 days, depending on the length of time the stove is used and the type of pellet used.To access the drawer, open the door (see figure 1) and extract the ashes drawer (see figure 2).N.B.: The operation must be carried out when the stove is cold, using a drum-type vacuum cleaner.
1 2
HOW TO REMOVE THE FLAME TRAP:
N.B.: REMOVE AND CLEAN THE FLAME TRAPREGULARLY.
Phase A Phase B
POSITION OF THEFLAME TRAPSLOT
FRONT FLAME TRAP REST
REAR FLAME TRAP REST
Brochure for Francesca model
Cleaning the suction duct (every 1000 hours):
The suction duct must be cleaned once every 3 months (the time may vary depending on the quality of the pellet used). Follow the opera-tions illustrated in the images below to access the inspection hatches.You are advised to agree this type of cleaning with your Ecoteck assistance centre.N.B.: Use a drum-type vacuum cleaner only.
How to access the inspection hatches:
1 2
3
Remove the 4 screws that le attach the rear grill to the side panels.
Remove the screws that attach the side panels to the stove.
Lift up the ceramic top
Brochure for Francesca model
4
5
Remove the screws that attachthe side panels to the top of the stove
Remove the side panel.
Brochure for Francesca model
INSPECTION HATCH(2 ON THE RIGHT SIDE)
INSPECTION HATCH (1 ON THE LEFT SIDE)
GASKET
GASKET
GASKET
SCRAPER
PARTS / FREQUENCY 1 DAY 2-3 DAYS 30 DAYS 60-90 DAYS 1 SEASON
Fire pot
Ashes drawer
Glass
Suction duct
Door gasket
Tube bundle scraper
Flue
Combustion chamber
Vacuum clean the pellet tank
Brochure for Francesca model
TECHNICAL DIAGRAM
981
257
578
4345
8
85,5
20
1029,4
749,5
385
19043
2
257
80
35
399
107
82
438
1646
1
Mod
.D
ES
CR
IZIO
NE
Dat
aD
is.
App
r.M
ODI
FIC
HE
5700
0-00
-001
-
MO
D.
__
A1
(SC
HE
ET)
FOR
MA
TO
FRA
NC
ESC
A 2
007
----
CO
MPL
ESSI
VO S
TUFA
"FR
ANC
ESC
A 20
07"
TOLL
ER
AN
ZE G
EN
ER
ALI
PE
R Q
UO
TE L
INE
AR
I, A
NG
OLA
RI,
SM
US
SI E
RA
CC
OR
DI,
CLA
SS
E F
INE
UN
I EN
227
68-1
, DO
VE
NO
N IN
DIC
ATE
1:5
FCH
C.F
acec
chia
mar
tedì
11
sett
embr
e 20
07
SC
ALA
(SC
ALE
)D
EN
OM
INA
ZIO
NE
(DE
NO
MIN
ATI
ON
)
s.r.l
ECOTECK
MA
TRIC
E D
I PIE
GA
will be legally pursued.
diritti a rigore di legge.
and must not be released to other parties without written consent any infringement in any way utilized for the manifacture of the component of unit herein illustratedAll proprietary right reserved by Society ECOTECK s.r.l. This drawing shall not be reproduced or
ne venire comunicato a terzi o riprodotto. La Societa' proprietaria tutela i propridisegno non potra' essere comunque utilizzato per la costruzione dell' oggetto rappresentatoProprieta' della Societa' ECOTECK s.r.l. Senza autorizzazione scitta della stessa, il presente
MO
DIF
ICA
RE
SO
LO S
U C
AD
(CH
EC
KE
D)
CO
NTR
.
(WE
IGH
T)P
ES
O K
g
DIS
.
MA
TER
IALE
(MA
TER
IAL)
(DE
SIG
NE
R)
DA
TA
(DR
WG
NR
.)N
. DIS
EG
NO
(DA
TE)
CA
D D
RA
WN
ING
HA
ND
LIN
G O
N C
AD
SY
STE
M O
NLY
MO
DE
LLO
(MO
DE
L)
TRA
TTA
M. S
UP
ER
FIC
IALE
Brochure for Francesca model
Aico SpAVia Kupfer, 31 - 25036 Palazzolo sull’Oglio / BS - ITALYTel. +39.030.7402939Fax. +39.030.7301758Internet : www.ecoteck.itE-mail : [email protected]
Aico SpA does not assume any responsibility for any errors in this booklet and considers itself free to make any variations to the features of its products without notice.