bornquist inc submittal tbp-1a-d · series: e-sv pressure at shutoff: 36 psi size: 1sv head at...
TRANSCRIPT
BORNQUIST INC SUBMITTAL TBP-1A-D
JOB: UNIT TAG: ENGINEER: SUBMITTED BY: DATE: CONTRACTOR: APPROVED BY: DATE:
Description:
The Tenant Boost Package (TBP) is a pre-engineered system of components designed to draw condenser
water for a localized Computer Room Air Conditioning (CRAC) unit or local tenant HVAC system from an
existing chilled water loop in the building. Each model is suitable for a range of flows and pressures.
The wall-mountable VFDs are plenum rated suitable for mounting in air compartments. e-SV units shall
be rated to 300 PSI Working Pressure.
The system can receive a signal from the CRAC/HVAC unit to start and stop the system duty pump or
configured for continuous run. Duplex units can alternate the duty pump as well as start the standby
pump in the event of a pump/VFD failure.
Duplex Tenant Boost Package Component Schematic
BORNQUIST INC SUBMITTAL TBP-1A-D
JOB: UNIT TAG: ENGINEER: SUBMITTED BY: DATE: CONTRACTOR: APPROVED BY: DATE:
Duplex Models
Included Components: Operating Range Data (Min/Max - Flow/Head): Note: All components pre-sized to system conditions and major component line sizes.
Duty/Standby Operation Note: Base models listed below. See model selection page for full part number information.
• (2) Goulds e-SV Pump
• (2) Danfoss FC-102 VFD
• (2) (1) B&G UBY (Isolation Valve/Y-Strainer)
• (2) Metraflex Check Valve
• (2) Nibco Discharge Isolation Ball Valve
• (2) B&G Circuit Setter Plus
• (4) Kinetics Pipe Hangers
• (4) Metraflex Flex Connectors
• (4) Weiss Pressure Gauge
• (2) United Electric DP Switches
• (1) Bornquist Sequencing Panel
Models:
• BTBKD1SV12 – 1 GPM@80’ to 5 GPM@40’
• BTBKD3SV18 – 3 GPM@140’ to 10 GPM@100’
• BTBKD10SV9 – 10 GPM@110’ to 30 GPM@50’
• BTBKD22SV9 – 20 GPM@140’ to 60 GPM@90’ Optional Components:
• Differential Pressure (DP) Sensors for variable speed control
• Redundant Y-Strainer / Isolation Valve
e-SV Models: Composite Selection Range
BORNQUIST INC SUBMITTAL TBP-1A-D
JOB: UNIT TAG: ENGINEER: SUBMITTED BY: DATE: CONTRACTOR: APPROVED BY: DATE:
Bornquist Tenant Boost Package Part Number Breakdown
Options
A = Differential (DP) Sensor
B = VFD Bypass (Simplex Models Only)
C = Redundant Y-Strainer / Isolation Valve
System Voltage
2 = 208-230V, 1PH 3 = 208-230V, 3PH
4 = 460V, 3PH
Branch Piping Size
A = 1-1/4" B = 2"
Maximum Pressure Rating
300 = 300 PSI 175 = 175 PSI
Pump HP Rating
C=1/2 D=3/4 E=1 F=1 1/2 G=2
H=3 J=5
Pump Model, Flow/Head
1SV12 = 1e-SV, 12 Stg, Min=1 GPM@80', Max=5 GPM@60'
3SV18 = 3e-SV, 18 Stg, Min=5 GPM@140', Max=10 GPM@100'
10SV9 = 10e-SV, 9 Stg, Min=10 GPM@110', Max=30 GPM@90'
22SV9 = 22e-SV, 9 Stg, Min=25 GPM@140', Max=60 GPM@100'
XL5545 = ecocirc XL 55-45, Min=1 GPM@50', Max=40 GPM@10'
Pump Configuration
S = Simplex, 1 Pump
D = Duplex, 2 Pump (Duty/Standby)
Package or Kit
K=Kit P=Package
Product Type
BTB = Bornquist Tenant Boost
BTB K D 1SV12 C 300 A 2 - A
PUMP SUBMITTAL DATA
Quote Number: 9002-170518-061 1SV12GA8F20H - 0.5HP 4/60/3 TE 362 12STG
DO NOT USE FOR CONSTRUCTION UNLESS CERTIFIED Certified by
Date of Certification
Pump Serial Number
Project Name Tenant Boost Pumps
Tag
ENGINEERING DATA
Hydraulics
FLOW AT DESIGN 3 USGPM
FLOW AT DUTY 3 USGPM
HEAD AT DESIGN 80 ft
HEAD AT DUTY 81 ft
NPSHr 2.0 ft
Pump
PRODUCT NUMBER 1SV12GA8F20H
SIZE 1SV
NUMBER OF STAGES 12
MATERIAL Cast Iron/304SS
SUCTION SIZE 1-1/4 inch
DISCHARGE SIZE 1-1/4 inch
POWER AT DESIGN 0.13 Hp
EFFICIENCY AT DESIGN 46.4 %
APPROXIMATE NET WEIGHT 65 lbs
Motor
PART NUMBER W04A34E2BB3S
NAMEPLATE HORSEPOWER 0.5 Hp (0.37 kW)
PHASE 3
MAXIMUM FREQUENCY 60 Hz
VOLTAGE 208-230/460 V
SPEED 1800 RPM
ENCLOSURE TEFC
FRAME SIZE 56C
Impeller
IMPELLER TYPE Radial Impeller
QUANTITY 12
Mechanical Seal
SHAFT SEAL Carbon/Silicon Carbide/Viton
Options
LOW NPSH No
STANDARD EQUIPMENT / CAPABILITY
Pump
The e-SV pump is a non-self-priming vertical multistage pump coupled to a standard
motor. The liquid end, located between the upper cover and the pump casing, is held in
place by tie rods. The pump casing is available with different configurations and
connection types.
• Delivery: up to 700.0 gpm/ Head: up to 1200 ft
• Temperature of pumped liquid: -20.0°F to 250.0°F standard version
• Direction of rotation: clockwise looking at the pump from the top down (marked with
an arrow on the adapter and on the coupling).
• G - Cast Iron/304SS ANSI Flange with Class 250 Flange Rating
• Maximum Allowable Working Pressure of 362 Psi g
• Seal housing chamber designed to prevent the accumulation of air in the critical area
next to the mechanical seal
• Mechanical seal according to EN 12756 (ex DIN 24960) and ISO 3069
• Versions with ANSI flanges that can be coupled to ANSI counter-flanges
• Threaded oval counter-flanges made of stainless steel are standard supply for the T
versions
• Easy maintenance. No special tools required for assembly or disassembly
• Standard version for temperatures ranging from: 0°F to 250°F (optional to 300°F)
Motor
• Standard NEMA 56C Frame motor totally enclosed fan cooled
• 1800 RPM nominal
• 3 phase version, 4 pole: 208-230/460 V, 60Hz, 0.5 Hp
• Reduced axial thrusts enable the use of standard NEMA TC motors that are easily
found in the market
OUTLINE DRAWING
Quote Number: 9002-170518-061 1SV12GA8F20H - 0.5HP 4/60/3 TE 362 12STG
Weight Dimensions
65 lbs L1 20.35 inch
L2 9.91 inch
D1 6.19 inch
DO NOT USE FOR CONSTRUCTION UNLESS CERTIFIED Certified by
Date of Certification
Pump Serial Number
Project Name Tenant Boost Pumps
Tag
PERFORMANCE CURVE
Quote Number: 9002-170518-061 1SV12GA8F20H - 0.5HP 4/60/3 TE 362 12STG
DO NOT USE FOR CONSTRUCTION UNLESS CERTIFIED Certified by
Date of Certification
Pump Serial Number
Project Name Tenant Boost Pumps
Tag
Sizing Critera Series: e-SV Pressure at Shutoff: 36 psi
Size: 1SV Head at Shutoff: 83 ft
Number of Impellers: 12 Head at Design: 80 ft
Number of Trimmed Impellers: N/A Head at Duty: 81 ft
Trimmed Impeller Size: N/A Best Efficiency: 50.7 %
Speed: 1800 RPM Efficiency at Design: 46.4 %
Curve Type: Standard NPSH NPSHr: 2.0 ft
Curve ID: 1SV12 Power at Design: 0.13 Hp
Maximum Flow: 6 USGPM Max Power on Design Curve: .17 Hp
PRODUCT DETAILS – 134L8488
• Danfoss VLT® HVAC Drive is dedicated to ventilation, heating, and refrigeration applications.
With a wide range of powerful standard and optional features, the VLT® HVAC Drive provides
the lowest overall cost of ownership.
Product Data
1.1 KW / 1.5 HP, 200 - 240 VAC, Single phase, IP55 / Type12 Backplate
Mains Disconnect, Graphical Loc. Cont. Panel, RFI Class A2 (C3), Not coated PCB,
No A Option, No B Option, No C1 option, No D option,
Smooth imperial cable entr, No adaptation, No brake chopper, Frame Size:
A5
FC-102P1K1S2P55H2XGX1SXSXXXXAXBXCXXXXDX
MECHANICAL DRAWING: 176U5289
ELECTRICAL DRAWING: 174N3179
SUBMITTAL
A-606.18B
JOB: REPRESENTATIVE: UNIT TAG: ORDER NO. DATE: ENGINEER: SUBMITTED BY: DATE: CONTRACTOR: APPROVED BY: DATE:
Model UBY Combination Ball Valve & Strainer
DESCRIPTION The Bell & Gossett UBYC is a combination wye strainer, full port shut-off valve and union for use in HVAC systems. Strainers are furnished with a 20 mesh stainless steel screen, hose end drain valve for purging, and one pressure/temperature port for commissioning. A variety of pipe connections are available on both the fixed and union ends. An optional valve with Bypass port and additional pressure/temperature ports is available.
CONSTRUCTION Body: Brass Ball: Full Port Chrome Plated Ball Seal: PTFE Stem: Stainless Steel (Explosion Proof) O-Rings: EPDM Strainer: 20 Mesh Stainless Steel
MAX. WORKING PRESSURE 400 psig (2,758 kPa) MAX. OPERATING TEMPERATURE -4°F (-20°C) to 250°F (121°C)
UBY A-606.18B Page 2
NOTE: THIS IS THE DEFAULT MODEL IF NO ADDITIONAL PT PORTS OR BYPASS IS REQUIRED.
*All dimensions +/- 0.125 (3.2 mm) tolerance. Dimensions are subject to change. Not to be used for construction purposes unless certified.
Valve Size Fixed End
Connection Fixed End Cv
DIMENSIONS* INCH (mm)Approx. Weight
Lbs. (kg)A B C D E F G H J K T (Max) L (Max)
½"Sweat
Female 7.4
1.303 (33.1)
5.417 (137.59)
2.918 (74.12)
1.672 (42.46)
1.92 (48.77)
1.135 (28.82)
1.872 (47.56)
3.533 (89.74)
1.375 (34.93)
0.688 (14.46)
.6 (15.24)
7.140 (181.24)
1.5 (.68)
½" NPT Female 7.4 1.055 (26.8)
5.169 (131.29)
2.918 (74.12)
1.672 (42.46)
1.92 (48.77)
1.135 (28.82)
1.872 (47.56)
3.533 (89.74)
1.375 (34.93)
0.688 (17.46)
.650 (16.51)
7.19 (182.63)
1.5 (.68)
¾"Sweat
Female 8
1.559 (39.6)
5.865 (148.96)
3.024 (76.82)
1.819 (46.2)
2.114 (53.7)
1.27 (32.25)
2.064 (52.43)
3.533 (89.74)
1.66 (42.16)
0.83 (21.08)
.85 (21.59)
7.717 (196)
1.81 (.82)
¾" NPT Female 8 1.189 (30.2)
5.494 (139.56)
3.024 (76.82)
1.819 (46.2)
2.114 (53.7)
1.27 (32.25)
2.064 (52.43)
3.533 (89.74)
1.66 (42.16)
0.83 (21.08)
.8 (20.32)
7.667 (194.74)
1.81 (.82)
1"Sweat
Female 16
1.846 (46.9)
7.13 (181.1)
4.029 (102.33)
2.126 (54)
2.323 (59)
1.332 (33.83)
2.603 (66.11)
4.288 (108.93)
1.910 (48.51)
.955 (24.26)
1.010 (25.65)
9.233 (234.52)
3.06 (1.63)
1" NPT Female 16 1.421 (36.1)
6.704 (170.29)
4.029 (102.33)
2.126 (54)
2.323 (59)
1.332 (33.83)
2.603 (66.11)
4.288 (108.93)
1.910 (48.51)
.955 (24.26)
.900 (22.86)
9.123 (231.72)
3.06 (1.63)
1¼"Sweat
Female 18
2.17 (55)
7.89 (200.4)
4.374 (111.1)
2.882 (73.2)
2.475 (62.87)
1.561 (39.65)
3.105 (78.87)
5.158 (131.02)
2.43 (61.72)
1.215 (30.86)
1.070 (27.18)
10.894 (276.71)
4.44 (2.01)
1¼" NPT Female 18 1.634 (41.5)
7.357 (186.87)
4.374 (111.1)
2.882 (73.2)
2.475 (62.87)
1.561 (39.65)
3.105 (78.87)
5.158 (131.02)
2.43 (61.72)
1.215 (30.86)
1.00 (25.4)
10.824 (274.93)
4.44 (2.01)
1½"Sweat
Female 46
2.41 (61.2)
9.16 (232.6)
4.923 (125.04)
3.12 (79.12)
2.72 (69)
1.815 (46.11)
4.227 (107.37)
5.16 (131)
2.82 (71.63)
1.41 (35.81)
1.23 (31.24)
12.432 (315.77)
7.25 (3.29)
1½" NPT Female 46 1.83
(46.5) 8.58
(217.9) 4.923
(125.04) 3.12
(79.12) 2.72 (69.)
1.815 (46.11)
4.227 (107.37)
5.16 (131)
2.82 (71.63)
1.41 (35.81)
1.250 (31.75)
12.452 (316.28)
7.25 (3.29)
2"Sweat
Female 54
2.943 (74.74)
10.16 (258.1)
5.368 (136.35)
3.72 (94.5)
2.961 (75.21)
1.897 (48.19)
4.441 (112.81)
6.58 (167.13)
3.5 (88.9)
1.75 (44.45)
1.48 (37.59)
14.398 (365.71)
10 (4.54)
2" NPT Female 54 2.185 (55.5)
9.4 (238.8)
5.368 (136.35)
3.72 (94.5)
2.961 (75.21)
1.897 (48.19)
4.441 (112.81)
6.58 (167.13)
3.50 (88.9)
1.75 (44.45)
1.170 (29.72)
14.088 (357.84)
10 (4.54)
Xylem Inc. 8200 N. Austin Avenue Morton Grove, IL 60053 Phone: (847)966-3700 Fax: (847)965-8379 www.bellgossett.com Bell & Gossett is a trademark of Xylem Inc. or one of its subsidiaries. © 2014 Xylem Inc.
A
B
1 2 3
4
5
6
7
MODEL BSNSCREWED-END BRONZE CHECK VALVE
8/28/2013
NONE BSN
NOTE:Valve is designed for liquid service only. Install 3 to 4 pipe diameters downstreamfrom pump discharge or elbow to avoid flow turbulence.
DESIGN SPECIFICATIONS:Maximum Temperature: 250 FMaximum Pressure:
Saturated Steam - 125 PSINon-Shock W.O.G. - 250 PSI
JC 8/28/2013
Qty. Part Number Size (in) A (in) B (in) Weight
(Lbs) Project Info
BSN0050 1/2 2-1/16 1-3/8 0.36BSN0075 3/4 2-1/4 1-5/8 0.48BSN0100 1 2-5/8 2 0.77BSN0125 1-1/4 2-15/16 2-3/8 1.14BSN0150 1-1/2 3-5/16 2-3/4 1.63BSN0200 2 3-11/16 3-3/8 2.27
ITEM PART NAME MATERIAL1 BODY BRONZE ASTM B584 ALLOY C844002 STEM STAINLESS STEEL ASTM 582 ALLOY C303003 SPRING STAINLESS STEEL TYPE 3164 DISC HOLDER STAINLESS STEEL TYPE 3015 DISC TEFLON6 SEAT SCREW STAINLESS STEEL ASTM A2767 BODY END BRONZE ASTM B584 ALLOY C84400
REV. DATE
DRAWN BY:APPROVED: DATE:
DATE:
SCALE: DRAWING NUMBER:
CUSTOMER:__________________________________
PROJECT:____________________________________
ENGINEER:___________________________________
2323 W. HUBBARD ST.CHICAGO, IL 60612TEL: 312-738-3800FAX: 312-738-0415WWW.METRAFLEX.COM
DKISH
NIBCO INC. WORLD HEADQUARTERS • 1516 MIDDLEBURY ST. • ELKHART, IN 46516-4740 • USA • PH: 1.800.234.0227 TECH SERVICES PH: 1.888.446.4226 • FAX: 1.888.336.4226 • INTERNATIONAL OFFICE PH: +1.574.295.3327 • FAX: +1.574.295.3455
www.nibco.com5
A H E A D O F T H E F L O W®
www.nibco.comRevised 4/29/2015
Brass Ball ValvesTwo-Piece Body • Full Port • Blowout-Proof Stem • PTFE Seats¹⁄₄"-2" 600 PSI/41 .4 Bar Non-Shock Cold Working Pressure2¹⁄₂"-4" 400 PSI/27 .6 Bar Non-Shock Cold Working Pressure
T-FP-600AThreaded
MATERIAL LIST PART SPECIFICATION
1 . Body Forged Brass2 CU > 57% 2 . End Cap Forged Brass2 CU > 57% 3 . Ball Seat PTFE 4 . Ball Brass, Chrome Plated 5 . Stem Brass 6 . O-Ring (Stem Seal)* Fluorocarbon (FKM) 7 . Stem Packing PTFE 8 . Packing Nut Brass 9 . Lever Handle 1 Steel, Plated 10 . Lock Washer* Stainless Steel 11 . Handle Nut 1 Stainless SteelNote: * Parts 6 and 10 are applicable of S-FP-600A only .
1 Due to Standard Approvals, Lever Handles and Nuts are not interchangeable between Solder and Threaded .
2 For Material Certification, contact NIBCO Technical Services .
S-FP-600AC x C
T-FP-600ANPT x NPT
DIMENSIONS—WEIGHTS—QUANTITIES Dimensions
T-FP-600A S-FP-600A T-FP-600A S-FP-600A T-FP-600A S-FP-600A Port Size A A B B C C D T-FP-600A S-FP-600A T-FP-600A S-FP-600N In . mm . In . mm . In . mm . In . mm . In . mm . In . mm . In . mm . In . mm . Lbs . Kg . Lbs . Kg . Ctn . Qty . Ctn . Qty . ¹⁄v 8 1 .76 45 — — 1 .73 44 — — 3 .54 90 — — .39 10 .33 .15 — — 18 — C⁄₈ 10 1 .76 45 1 .75 44 1 .73 44 1 .58 40 3 .54 90 3 .78 96 .39 10 .30 .14 .38 .17 18 18 ¹⁄₂ 15 2 .05 52 2 .01 51 1 .92 49 1 .78 45 3 .54 90 3 .78 96 .59 15 .44 .20 .40 .18 18 18 C⁄v 20 2 .36 60 2 .74 70 2 .09 53 2 .13 54 3 .78 96 3 .98 101 .75 19 .66 .30 .67 .30 12 12 1 25 2 .76 70 3 .35 85 2 .56 65 2 .52 64 4 .53 115 4 .41 112 .98 25 1 .10 .50 1 .12 .51 6 6 1¹⁄v 32 3 .31 84 3 .78 96 2 .95 75 2 .65 67 4 .53 115 5 .04 128 1 .26 32 1 .57 .71 1 .49 .67 4 4 1¹⁄₂ 40 3 .66 93 4 .42 112 3 .35 85 3 .12 79 5 .51 140 6 .22 158 1 .57 40 2 .40 1 .09 2 .38 1 .08 2 2 2 50 4 .18 106 5 .34 136 3 .68 93 3 .41 87 5 .51 140 6 .22 158 1 .97 50 3 .37 1 .53 3 .62 1 .64 2 2 2¹⁄₂ 65 5 .38 137 6 .28 160 4 .76 121 4 .76 121 8 .66 220 8 .66 220 2 .56 65 7 .60 3 .45 6 .36 2 .88 3 3 3 75 6 .04 153 7 .15 182 5 .08 129 5 .08 129 8 .66 220 8 .66 220 2 .95 75 9 .36 4 .24 8 .32 3 .77 2 2 4 100 7 .39 188 — — 5 .87 149 — — 9 .61 244 — — 3 .89 99 16 .85 7 .64 — — 1 —
S-FP-600ASolder
CSA CERTIFIED TO ASME B16 .44 AND CR91-002 (THREADED ¹⁄v"-4") • UL LISTED (THREADED ¹⁄v"-4")
• FM APPROVED (THREADED ¹⁄v"-2")ThreadedCSA (¹⁄v" - 4"): • CR91-002: ¹⁄₂ psig, 2 psig, and 5 psig (these are specific approved categories) • ASME B13 .44: 125 psig (maximum) • Temperature is -4° F to 194° F
Threaded
FM (1/4" - 2"): • 175wwp Threaded
UL, Gas and Oil (¹⁄v" - 4"): • YQNZ, Compressed Gas Shutoff Valves: 250 psi • YRBX, Flammable Liquid Shutoff Valves: 250 psi • YRPV, Gas Shutoff Valves: 250 psi • YSDT, LP-Gas Shutoff Valves: 250 psi • MHKZ, Manual Valves: 250 psi
NOT FOR USE WITH POTABLE DRINKING WATER APPLICATIONS AFTER JANUARY 3, 2014 .
SUBMITTAL
A-549LFP(D) JOB: REPRESENTATIVE: UNIT TAG: ORDER NO. DATE: ENGINEER: SUBMITTED BY: DATE: CONTRACTOR: APPROVED BY: DATE:
Circuit Setter Plus
Calibrated Balance Valves with NPT and Solder Connections
LEAD FREE*
DESCRIPTION The Bell & Gossett CIRCUIT SETTER PLUS and CIRCUIT SETTER PLUS "RF" calibrated balance valves are a precision machined ball type triple purpose balancing instrument. They are precisely calibrated for use as a presettable balance valve, variable orifice flow meter and positive shut-off service valve. Valves are furnished with a calibrated nameplate and memory stop indicator which permits a preset to a fixed open position and then closed for service without disturbing valve setting. Valves are equipped with capped readout valves fitted with internal check valves and 1/4" NPT tapped and plugged drain port.
CONSTRUCTION Body: Brass ASTM B283-C69300*
Ball: 304 Stainless Steel Seat Rings: Glass and Carbon filled TFE Readout Valves: Brass with EPT check valves Stem "O" Ring: EPDM MAXIMUM WORKING PRESSURE NPT Models: 400 psig (2758 kPa) Sweat Models: See table below MAXIMUM OPERATING TEMPERATURE -4°F(-20°C) to 250°F(121°C) *Contains less than 0.25% lead content by weight on wetted surfaces. AB1953 and CSA Certified. Vermont 152S, Maryland House Bill HB.372, Senate Bill S.3874, and NSF-61 Annex G Compliant.
LEAD-FREE CIRCUIT SETTER PLUS Calibrated Balance Valves A-549LFP(D)
**Contains less than 0.25% lead content by weight on wetted surfaces.
CSA CERTIFIED: AB1953; Vermont S152; Maryland House Bill 372 [statute 12-605]. ANSI/NSF-61 Annex G Compliant.
DIMENSIONS AND WEIGHTS *
MODEL NUMBER
PART NUMBER SIZE
CONNECTION TYPE
DIMENSIONS IN INCHES (MM) WEIGHT IN LBS. (KG)A B C
RF-1/2S LF 117410LF 1/2" SWEAT2.91
(73.9)1.82
(46.2)2.85
(72.4)0.6
(0.27)
RF-3/4S LF 117411LF 3/4" SWEAT3.51
(89.2)2.05
(52.1)3.10
(78.7)0.75
(0.34)
CB−1/2S LF 117412LF 1/2" SWEAT2.91
(73.9)1.82
(46.2)2.85
(72.4)1
(0.45)
CB−3/4S LF 117413LF 3/4" SWEAT3.51
(89.1)2.05
(52.1)3.10
(78.7)1.25 (0.6)
CB−1S LF 117401LF 1" SWEAT4.29 (109)
2.33 (59.2)
3.33 (84.6)
2 (0.9)
CB−1-1/4S LF 117402LF 1-1/4" SWEAT4.91
(124.7)3.08
(78.2)3.69
(93.7)3.5
(1.6)
CB−1-1/2S LF 117403LF 1-1/2" SWEAT5.21
(132.3)3.27 (83)
3.95 (100.2)
3.8 (1.7)
CB−2S LF 117404LF 2" SWEAT6.31
(160.3)3.83
(97.4)4.44
(112.8)6.2
(2.8)
CB−1/2 LF 117414LF 1/2" NPT2.94
(74.7)1.98
(50.3)3.02
(76.7)1.25 (0.6)
CB−3/4 LF 117415LF 3/4" NPT3.06
(77.7)2.17
(55.1)3.12
(79.2)1.5
(0.7)
CB−1 LF 117416LF 1" NPT3.81
(96.8)2.47
(62.7)3.42
(86.9)2
(0.9)
CB−1-1/4 LF 117103LF 1-1/4" NPT4.41 (112)
3.19 (81)
3.69 (93.7)
3.5 (1.6)
CB−1-1/2 LF 117104LF 1-1/2" NPT4.42
(112.3)3.37
(85.6)3.95
(100.2)3.8
(1.7)
CB−2 LF 117105LF 2" NPT5.13
(130.3)3.98
(101.1)4.44
(112.8)6.2
(2.8)
CB−2-1/2 LF 117106LF 2-1/2" NPT6.00
(152.4)4.51
(114.6)4.83
(122.6)9
(4.1)
CB−3 LF 117107LF 3" NPT6.50
(165.1)5.12
(130.0)5.44
(138.2)12
(5.4)*All dimensions +/-0.125 (3.2 mm) tolerance. Dimensions are subject to change. Not to be used for construction purposes unless certified.
TYPICAL SPECIFICATION Furnish and install as shown on plans with manufacturer recommendations Model CB or "RF" calibrated balance valves. PRE-SET BALANCE FEATURE Valves to be designed to allow installing contractor to pre-set balance points for proportional system balance prior to system start-up in accordance with pre-set balance schedule. VALVE DESIGN AND CONSTRUCTION All valves 1/2" to 3" pipe size to consist of Lead Free Brass** body/SS ball construction with glass and carbon filled TFE seat rings. Valves to have differential pressure read-out ports across valve seat area. Read-out ports to be fitted with internal EPT inserts/check valves. Valve bodies to have 1/4" NPT tapped drain/purge port. Valves to have memory stop feature to allow valve to be closed for service and then reopened to set point without disturbing balance position. All valves to have calibrated nameplates to assure specific valve settings. Valves shall be designed for positive shut-off.
DESIGN PRESSURE/TEMPERATURE A. 1/2" - 3" NPT connections 400 psig (2069 kPa) at 250°F (121°C) B. 1/2" - 2" Sweat connections (see table page1) All balance valves to be ITT Bell & Gossett Model No. CB−____________LF or Model No. RF-____________LF (note sizes). IMPORTANT: When monitoring system flow, care must be exercised to avoid direct skin or eye contact with liquids that may escape. Liquids with temperatures in excess of 120°F (49°C) may cause burns. Bell & Gossett Circuit Setter Balance Valves are not recommended for use with meter connections pointing downward.
Xylem Inc. 8200 N. Austin Avenue Morton Grove, IL 60053 Phone: (847)966-3700 Fax: (847)965-8379 www.bellgossett.com Bell & Gossett is a trademark of Xylem Inc. or one of its subsidiaries. © 2016 Xylem Inc.
1 All dial ranges available in dual scale - psi & Kpa, psi & Kg / cm2. Ranges 15psi thru 200psi available dual scale - psi & Ft H2O.
PRESSURE (psi) - Series 4CTSRange 1 Figure interval Minor graduation
0-15 1 0.20-30 5 0.50-60 5 1.00-100 10 1.00-160 20 2.00-200 20 2.00-300 50 5.00-400 50 5.00-600 50 10.0
COMPOUND Figure interval Minor graduationRange in Hg psi in Hg psi
30"Hg-15psi 10 5 1 0.530"Hg-30psi 10 5 1 130"Hg-60psi 10 10 2 230"Hg-100psi 15 10 5 230"Hg-150psi 30 20 2 2
VACUUMRange Figure interval Minor graduation
0-30"Hg 5"Hg 0.5"Hg
QTY. CAT. NO. DIAL DIA. RANGE TAG 4CTS 41/2 "4CTS 41/2 "4CTS 41/2 "4CTS 41/2 "4CTS 41/2 "
CUSTOMER
PROJECT
ENGINEER
PRO or P.O. NO.
WEISS INSTRUMENTS, INC.HOLTSVILLE, NEW YORK 11742
DESCRIPTION:41/2" HVAC Pressure Gauge
Series 4CTS
DRAWN BY: DATE: DRAWING:
© 2005 Weiss Instruments, Inc. - All rights reserved
SERIES A B E L NPT
INCH 4.62 1.12 1.062 .4374CTS 1/4"
MM 117.3 28.4 26.9 11.09
CASE -Drawn stainless steel, with push-in Lexan window.TUBE & SOCKET -Phosphor bronze. Brass socket and1/4" male NPT lower connection. Soft soldered connection.DIAL- White coated metal lithographed with black graduationslines and numerals.
MOVEMENT - All brass construction,precision gear and pinion.
POINTER - Slotted adjustable.
ACCURACY -1% ANSI-ASME B40.1 Grade 1A.
features
• Sealed Metal Bellows Sensors
• Welded 316 Stainless Steel Sensors
• Gasketed Die-Cast Aluminum Enclosure with Epoxy Coating
• Single Switch Output
• Adjustable Ranges: 30 "Hg Vac to 90 psid (-1 to 6 bar)
J 2 1 K - B - 0 5
DIFFERENTIAL PRESSURE SWITCH
J21K seriesJ2
1K
se
ries
J 2 1 K - B - 0 5 w w w . u e o n l i n e . c o m 54 w w w . u e o n l i n e . c o m J 2 1 K - B - 0 5
J21K Series
model chart
Model Adjustable Set Deadband Differential Working Point Range Proof Pressure** Pressure* Low end of range on fall; High end of range on rise psid bar psi bar psid bar psi bar (unless noted) (unless noted) (unless noted) (unless noted)
Welded 316L stainless steel bellows with 1/2” NPT (female) pressure connections
S127B 30 "Hg Vac to 0 -1 to 0 0.4 to 0.6 "Hg 13,5 to 20,3 mbar 15 1.0 30 "Hg Vac to 0 -1 to 0S140B 0 to 6 0 to 0,4 0.1 to 0.4 6,9 to 27,6 mbar 6 0,4 30 "Hg Vac to 30 -1 to 2,1 S150B 0 to 40 0 to 2,8 0.3 to 0.7 20,7 to 48,3 mbar 300 20,7 30 "Hg Vac to 300 -1 to 20,716021 1 to 15 0,07 to 1,0 0.1 to 0.6 6,9 to 41,4 mbar 125 8,6 30 "Hg Vac to 125 -1 to 8,6
316L welded stainless steel bellows with 1/4" NPT (female) pressure connections
357 0 to 70 0 to 4,8 2 to 4 0,1 to 0,3 70 4,8 30 "Hg Vac to 350 -1 to 24,1
Brass bellows with 1/4” NPT (female) pressure connections
127 30 "Hg Vac to 0 -1 to 0 0.4 to 0.6 "Hg 13,5 to 20,3 mbar 15 1.0 30 "Hg Vac to 0 -1 to 0140 0 to 6 0 to 0,4 0.1 to 0.4 6,9 to 27,6 mbar 6 0,4 30 "Hg Vac to 30 -1 to 2,1 150 0 to 40 0 to 2,8 0.3 to 0.7 20,7 to 48,3 mbar 40 2,8 30 "Hg Vac to 180 -1 to 12,416020 1 to 15 0,07 to 1,0 0.1 to 0.6 6,9 to 41,4 mbar 125 8,6 30 "Hg Vac to 125 -1 to 8,6
Phosphor bronze bellows with 1/4" NPT (female) pressure connections
232 0 to 25 0 to 1,7 0.6 to 1 41,4 to 68,9 mbar 25 1,7 30 "Hg Vac to 110 -1 to 7,6 254 0 to 90 0 to 6,2 2 to 4 0,1 to 0,3 90 6,2 30 "Hg Vac to 200 -1 to 13,8
*working pressure range: The pressure range within which two opposing sensors can be safely operated and still maintain set point adjustability.** Differential proof range: The maximum differential pressure to which a pressure sensor may be occasionally subjected, which causes no permanent damage. The unit may require calibration (e.g. start up, testing)
Representative: Bornquist IncCustomer: Project: Location Remarks: Application:
FLEX CONNECTOR SUBMITTAL
Connector Master Assembly 26930N/A
10/26/2017
*MOVEMENT REFERS TO MAXIMUM INTERMITTENT LATERAL OFFSET FROM CENTER.
RATED FOR 531 PSI @ 70°F.
MISC CONNECTOR NOTES:
STEAM: Steam connectors should be doublebraided regardless of operational pressure.
NSF 372 - LEAD FREE: The wetted surface of thisproduct contacted by water contains less thanone quarter of one percent (0.25%) of lead byweight. Material complies with state codes andstandards, where applicable, requiring reducedlead content.
PART NUMBER PIPE SIZE OAL MOVEMENT* BRAID LAYERSSF17A26A01250094 1.25" 9.5" .125" SINGLE
HOSE MATERIAL BRAID MATERIAL FITTING 1 FITTING 2 FITTING MATERIAL321 SS 304 SS RF FLANGE 300# THREAD CS/SCH 40
REV. DATE
DRAWN BY:APPROVED: DATE:
DATE:
SCALE: DRAWING NUMBER:
2323 W. HUBBARD ST.CHICAGO, IL 60612TEL: 312-738-3800FAX: 312-738-0415WWW.METRAFLEX.COM
DKISH
BORNQUIST ALTERNATING / SEQUENCING PANEL
208-230V/460V, 1Ø or 3Ø Up to 5 HP – 2 Pump VFD Controller
The 2-Pump Alternating / Sequencing panel utilizes a programmable controller interfaced to individual VFDs for each pump.
o Time Clock Alternation Feature o Primary Motor Fail Detection & Auto Switching Feature o Motor Run Counts, Hours Data Log o Motor Fail Data Log o Power Fail Data Log
• Terminal Blocks • Input Terminals For Remote VFD Fault Relay Feedback • Remote Monitoring Dry Contacts For Each Motor Run & Fail (5A Max) • UL 508A Listed • Documentation & Labeling • Remote VFDs Are Not Included (Supplied By Others)
Pump Control Scheme
External Control Signals
Input signals to the panel are (1) DI – Call for Cooling. Output signals for BAS are (1) Pump 1 Running, (1) Pump 1 Fail, (1) Pump 2 Running, (1) Pump 2 Fail.
VFD Control Signals
Each VFD will receive Start Signals (Dry Contacts) from the panel. Each VFD’s Drive Run Indication will be wired back to the panel.
7050 N. LEHIGH AVE. CHICAGO, IL 60646 PHONE (773) 774-2800/FAX (773) 763-6534
e-mail: [email protected] website: www.bornquist.com
MANUFACTURERS REPRESENTATIVES
• NEMA 4X Fiberglass Enclosure, Quarter Turn Latches • Main Disconnect Switch (Non-Fused) • Pump Running Light For Each Pump • Pump Fail Light For Each Pump • Siemens LOGO Controller • Programmable Controller With Onboard Display & Buttons
The sequence control panel is two (2) pump sequencer with (1) pump designated as the lead/duty pump and one (1) pump that is backup pump. The lead pump will run based upon a call for cooling contact closure (DI) to the panel or be wired for continuous run. Upon failure of a pump/VFD, the controller will start the back-up pump. The sequencer will alternate lead (duty) pump to equalize run time.
P1 RUNNING
GRN
P2 RUNNING
GRN
P1 FAIL
RED
P2 FAIL
RED
HANDOFF
AUTO HANDOFF
AUTO
e
h
Controls115 VAC CB 10A
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
1.11
1.12
1.13
1.14
1.15
1.16
1.17
1.18
1.19
1.20
1.21
1.22
1.23
1.24
1.25
VFD1208V
12A MAX
= Factory Wire= Field Wire
15
16
17
18
19
20
CONTROLS TRANSFORMER208-120V 100VA
H2H1
X1 X2
FUSES2A F1 F2
L1
L3
L2
CB 15A
From Main Power Panel208VAC, 3 Phase, 60 Hz.
Ground Wire
Panel Wiring DiagramModel BTB-SEQUENCER-01
OT 60F3Disconnect
Switch
G
LOGOSIEMENS6ED1-052-1FB00-0BA6
PUMP RUN LIGHTSIEMENS S3U SERIES
CR1A2A1
X2X1
L1 N
Q1
PUMP 1 FAILLIGHTIDEC HW SERIES
G PUMP RUN LIGHTSIEMENS S3U SERIES
CR2A2A1
X2X1
Q2
LOGO BASE
PUMP FAIL RESET i8AL1-2
EDW-CD-DAX-4267Rev. 1.0 © 10/10/17Page 1 of 2
CB 15A
PUMP 1 STARTIDEC RELAYRJ2S-C-D24
PUMP 1 STARTIDEC RELAYRJ2S-C-D24
i1
i2AUTO
HAND
i6
i7
VFD 1 RUNFEEDBACK
VFD 2 RUNFEEDBACK
PUMP 1 HOASWITCH
3
5
4
6
i5LEAD PUMPSTART CONTACT 1 2
VFD2208V
12A MAX
i3
i4AUTO
HAND
PUMP 2 HOASWITCH
R
CR3A2A1
X2X1
Q3 PUMP 1 FAILIDEC RELAYRJ2S-C-D24
PUMP 2 FAILLIGHTIDEC HW SERIES
R
CR4A2A1
X2X1
Q4 PUMP 2 FAILIDEC RELAYRJ2S-C-D24
AL1
AL2
7 8
CR1 1413
9 10
CR2 1413
PUMP 1RUN
PUMP 2RUN
11 12
CR3 1413
13 14
CR4 1413
PUMP 1FAULT
PUMP 2FAULT
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
2.12
2.13
2.14
2.15
2.16
2.17
2.18
2.19
2.20
2.21
2.22
2.23
2.24
2.25
2.26
2.27
2.28EDW-CD-DAX-4267Rev. 1.0 © 10/10/17Page 2 of 2
DWYER INSTRUMENTS, INC. | www.dwyer-inst.com76
Diff
eren
tial P
ress
ure
Tran
smitt
ers
PRES
SUR
E
WET/WET DIFFERENTIAL PRESSURE TRANSMITTER0.5% Accuracy, NEMA 4X (IP66) Enclosure
The SERIES 629C Wet/Wet Differential Pressure Transmitter monitors differential pressure of air and compatible gases and liquids with 0.5% accuracy. The design employs dual pressure sensors converting pressure changes into a standard 4 to 20 mA output signal or field selectable voltage. Small internal volume and minimal moving parts result in exceptional response and reliability. The terminal block, as well as a zero adjustment button, are easily accessed under the top cover. The Series 629C Differential Pressure Transmitter is designed to meet NEMA 4X (IP66) construction.
FEATURES/BENEFITS• Powered by either DC or AC - take advantage of most readily available power source reducing installation costs• Optional LCD does not need a separate power supply - lowers installed cost• Selectable voltage range - provides flexible choice for changing design or inputs for process/HVAC controllers being used to monitor and control • Push button zero (versus trim pot) - more simple zeroing provides easy install and calibration reducing installation time and possibility of operator error• Optional LCD indicator provides local status to identify operational condition
APPLICATIONS• Flow elements• Heat exchangers• Filters• Coils• Chiller• Pumps
SERIES 629C®
SPECIFICATIONSService: Compatible gases and liquids.Wetted Materials: Without valve: 316, 316L SS. Additional wetted parts with valve option: Buna-N, silicone grease, PTFE, brass 360, copper, and reinforced copolymer.Accuracy: ±0.5% FS (includes linearity, hysteresis & repeatability).Stability: ±1% FS/year.Temperature Limits: 0 to 200°F (-18 to 93°C).Compensated Temperature Limits: 0 to 175°F (-18 to 79°C).Pressure Limits: See Table 1.Thermal Effects: Avg 0.04%/°F (0.072%/°C) (includes zero and span).Power Requirements: 2-wire: 10 to 35 VDC; 3-wire: 13 to 35 VDC or isolated 16 to 33 VAC (reverse polarity protected).Output Signal: 2-wire: 4 to 20 mA; 3-wire: Field selectable 0 to 5, 1 to 5, 0 to 10, or 2 to 10 VDC.
Zero and Units: Push buttons inside conduit enclosure.Response Time: 400 msec.Loop Resistance: Current output: 0 to 1250 Ω (max), Rmax = 50(Vps-10); Voltage output: Minimum load resistance = 5 kΩ.Current Consumption: 28 mA (max).Electrical Connections: Removable terminal block; 1/2˝ female NPT conduit.Process Connections: 1/4˝ female or male NPT.Display: Optional 4-1/2 digit LCD field attachable display.Enclosure Rating: Designed to meet NEMA 4X.Mounting Orientation: Not position sensitive.Weight: 10.1 oz (286 g).Agency Approvals: CE.
3-7/64[78.83]
1-11/32[34.29]
43/64[17.15]
1-27/64[35.98]
1-31/32[50.16]
OPTIONALLCD
5-15/16 [150.88]1/4 NPT FEMALE FITTING
7 [177.80]OPTIONAL 1/4 NPT MALE FITTING
RANGERange Number Range
Working Pressure*
Over Pressure
010203040506070809111213141516171819
0 to 5 psid0 to 10 psid0 to 25 psid0 to 50 psid0 to 100 psid0 to 150 psid0 to 200 psid0 to 300 psid0 to 500 psid0 to 0.5 bar differential0 to 1 bar differential0 to 2 bar differential0 to 4 bar differential0 to 6 bar differential0 to 10 bar differential0 to 15 bar differential0 to 20 bar differential0 to 30 bar differential
10 psi20 psi50 psi100 psi200 psi300 psi400 psi600 psi1000 psi1 bar2 bar4 bar8 bar12 bar20 bar30 bar40 bar60 bar
50 psi50 psi120 psi250 psi500 psi750 psi1000 psi1200 psi2000 psi3 bar8 bar8 bar18 bar18 bar50 bar60 bar80 bar120 bar
*Pressures exceeding the working pressure limit may cause a calibration shift of up to ±3% of full scale.Note: Over pressure of all models with 3-way valve is 100 psi.
VIDEO ONLINE
USA: California Proposition 65WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
MODEL CHARTExample 629C -01 -CH -P1 -E1 -S1 -3V 629C-01-CH-P1-E1-S1-3VSeries 629C Wet/wet differential pressure transmitterRange 01
0203040506070809111213141516171819
0 to 5 psid0 to 10 psid0 to 25 psid0 to 50 psid0 to 100 psid0 to 150 psid0 to 200 psid0 to 300 psid0 to 500 psid0 to 0.5 bar differential0 to 1 bar differential0 to 2 bar differential0 to 4 bar differential0 to 6 bar differential0 to 10 bar differential0 to 15 bar differential0 to 20 bar differential0 to 30 bar differential
Housing CH Conduit housing, NEMA 4X (IP66)ProcessConnection
P1P2P3P4
1/4˝ male NPT1/4˝ female NPT1/4˝ male BSPT1/4˝ female BSPT
ElectricalConnection
E1E2E3E5E9
Cable gland with 3´ of prewired cableCable gland with 6´ of prewired cableCable gland with 9´ of prewired cable1/2˝ female NPT conduitM-12 4 pin connector
SignalOutput
S1S3
4-20 mAField selectable 0-5, 1-5, 0-10, 2-10 VDC
Options 3VATFCLCDNIST
3-way valveAluminum tagFactory calibration certificateLCD indicationNIST traceable certificate
ACCESSORIESModel DescriptionA-155A-228A-62X-LCDBBV-1B
Cable gland with 1/2˝ NPT male12˝ SS flex hoseField-upgradeable LCDMini SS 3-valve block manifold
YEAR LIMITEDWARRANTY