blind joint components · gfs6 efs6 caf6 hfsy6 nfs6 nefs6 3030 g 3060 g 3090 g 30120 g 5050 g 50100...
TRANSCRIPT
-6372 -6382
QNuts for Pre-Assembly Insertion Double Joints Joint Nut
Blind Joint ComponentsPre-Assembly Insertion Double Joint Kits for 6 Series (Slot Width 8mm) Aluminum Extrusions
Alterations necessary to use this componentS Type Hole Alterations
d P.791
QPre-Assembly Insertion Double Joint Kits Standard Type
QPre-Assembly Insertion Double Joint Kits Offset Nut Type
7.329
7.9
16.5R4.25Ø5.2
1.9
12
4.7
4.7
R4.25Ø5
7.9
1.9
12
7.329
16.5 Ø10.9
7.329
7.9
16.5R4.25Ø5.2
1.9
12
4.7
4.7
R4.25Ø5
7.9
1.9
12
7.329
16.5 Ø10.9
HDJSN(Standard)
HDJHSN(Offset Nut Type)
(1)Pre-Assembly Insertion Double Joints HDJFSN (SUS316 Equivalent, Sintered)
(1)Pre-Assembly Insertion Double Joints HDJFSN (SUS316 Equivalent, Sintered)
(2)Pre-Assembly Insertion Nuts HNTTSN (SUS316 Equivalent, Sintered)
Electrically Conductive
(2)Pre-Assembly Insertion Offset Nuts HNTHSN (SUS316 Equivalent, Sintering)
Electrically Conductive
MMaterial SUS304
HDJRN
Ø11
20.629.8
2-M5 Part Number Applicable Mass (g)
Unit Price Volume Discount RateType No. Applicable Extrusion Pre-Assembly Insertion Double Joints Screw 1~99 pc(s). 100~120
HDJRN 6 6 Series - 30 Square HDJFSN6 CBM5-40 43
Products shown on the photo come by ordering quantity 1.
Products shown on the photo come by ordering quantity 1.
QFeatures: Two screws are used for connection. Can be used to extend extrusions as well as mounting to plates. A joint type superior in mounting flexibility.
Pre-Assembly Insertion Double
JointsPart Number
Usable in any
direction
Usable in the short length
direction
Usable in the long length
direction
Usable in the direction where there is no flat surface at the
connecting part.
HDJSN6HDJHSN6HDJFSN6
NFS6HFS6GFS6EFS6CAF6
HFSY6NFS6
NEFS6
3030 G3060 G3090 G30120 G5050 G50100 G
100100 G6060 G6090 G60120 G
HFSF6EFSF6
NEFSF6
3030 G3060 G G5050 G6060 G
HFSH6EFSH6
3030 G3060 G G
NFSL6HFSL6
3030 G3060 G
HFSG6 6060 G
HFSB6 EFSB6
NEFSB6
3030 G3060 G3090 G30120 G5050 G6060 G
HFSFB6EFSFB6 3030 G
HFSLB6 3030 G3060 G
XNot applicable to extrusions not listed above.
Part Number Unit Price Volume Discount Rate
Type No. 1 ~ 99 set(s) 100~
HDJFSN(One set contains 2 pcs.)
6
E�One set is required to connect one place.
(1)Pre-Assembly Insertion Double Joint Single Item
Part Number
HDJSN6
Tighten with a hex wrench while adjusting the position.
JFSD6-3030L
HFS6-3030
Part Number - L
JFSD6-3030L - 1200
Part Number Joint Component
L 0.5mm Increment Extrusion
Built-in Joint ComponentA Required Wrench
for TighteningExtrusion Unit Price Joints,
OthersPre-Assembly Insertion Double Joints Quantity Less than 300mm 300mm or more (JPY/m)
JFSD 6-3030
L(Left End Face only)
100~4000 HFS6-3030(P.597) HDJHSN6
230 For M5
W(Double End Faces) 4
QFeatures: Pre-Assembly Insertion Double Joint installable without alterations. (No holes are required on the mating extrusion.)
Part Name MMaterial SSurface Treatment
Aluminum Extrusion A6N01SS-T5 Anodize
Pre-Assembly Insertion Double Joint Kits
Pre-Assembly Insertion Double JointsSUS316 Equivalent
-Offset NutHex Socket Head Cap Screw SUS304
Q�Aluminum Extrusions with Built-in Pre-Assembly Insertion Double Joints
JFSD6-3030L(Left End Face Pre-Assembly Insertion Double Joint Built-in Type)
JFSD6-3030W(Both End Face Pre-Assembly Insertion Double Joints Built-in Type)
EJoint components will be shipped loosely tightened.
L (Extrusion Length)
AA
Pre-Assembly Insertion Double Joints
L (Extrusion Length)
AA
Pre-Assembly Insertion Double Joints
E Alterations only on this page are available.
Alterations CodeSpec.
Extrusion Tap Depth
Right End Face Tapping
E JFS##-#### L is only applicable to Left End Face Joint Pre-Inserted Type.
RTP
6-3030 M8 24
o_99_41_67
Tapping
Right End Face
Alterations CodeSpec.
Extrusion H Hole Dia.
Right End Face Wrench Hole
E JFSC#-####LJFSS#-####L
Applicable to
6-3030 15 8
RCV
H
RCH H
H
Part Number
HDJRN6
With HNTTSN
• How to Use Pre-Assembly Insertion Double Joint Connection at the Corner (2)If HNTHSN6 is used instead of HNTTSN6−5, Pre-Assembly
Insertion Double Joint can be used at the corner of the extrusion.
HFS6-3030-200-LSH(P.597)
(P.777) (P.790)
(P.791)
HDJFSN6
CBM5-40
HDJFSN6
CBM5-40(P.777)
HFS6-3030-200-RDH(P.597) (P.607)
(P.597)
HDJRN6
HFS6-3030-200-LDH
CBM5-40
HDJRN6
HDJRN6
CBM5-40
HDJFSN6
HDJFSN6
HFS6-3030-200-LDH
HFSMG6-3030-A300-B300-R140-RSH
D Type Hole Alterations
S Type Hole Alterations
HFS6-3030-200-LSH(P.597)
(P.777) (P.790)
(P.791)
HDJFSN6
CBM5-40
HDJFSN6
CBM5-40(P.777)
HFS6-3030-200-RDH(P.597) (P.607)
(P.597)
HDJRN6
HFS6-3030-200-LDH
CBM5-40
HDJRN6
HDJRN6
CBM5-40
HDJFSN6
HDJFSN6
HFS6-3030-200-LDH
HFSMG6-3030-A300-B300-R140-RSH
D Type Hole Alterations
S Type Hole Alterations
Example of Extrusion Connection
QPre-Assembly Insertion Double Joint Connection (Connect the extrusion at the center.)
Example of Mounting to an Extrusion from the Bottom
Example of Connection with Bent Extrusions
HFS6-3030-200-LSH(P.597)
(P.777) (P.790)
(P.791)
HDJFSN6
CBM5-40
HDJFSN6
CBM5-40(P.777)
HFS6-3030-200-RDH(P.597) (P.607)
(P.597)
HDJRN6
HFS6-3030-200-LDH
CBM5-40
HDJRN6
HDJRN6
CBM5-40
HDJFSN6
HDJFSN6
HFS6-3030-200-LDH
HFSMG6-3030-A300-B300-R140-RSH
D Type Hole Alterations
S Type Hole Alterations
With HNTHSN
P
HDJFSN6
HFS6-3030-200-LSH
2-M
Example of Mounting an Extrusion on a Plate
Part NumberExtrusion Type M P
Type No.
HDJFSN 66 Series - 30 Square
520.6
6 Series - 50 Square 40.66 Series - 60 Square 50.6
ESame shape of different surface treatment or material can be also used.
Extrusion(A)
(2)
(3)SCB5-25
Extrusion(B)
Nuts protrude from the extrusions.
(2)HNTTSN6-5
HFS6-3030-1000Extrusion(A)
(1)HDJFSN6
Extrusion(B)
Step Front View Side View Sketch Drawing
1
2
3
4
5
6
(2) Pre-insert the pre-assembly insertion nuts into the extrusion (A).
Insert screw (3) into the extrusion (B) with S hole. This is, put the screw head through the S hole, then lift the screw along the slot until the screw tip is located above the S hole.
Insert Pre-Assembly Double Joint (1) into the extrusion (B) where the screws were inserted.
Put the screw through the hole of the Pre-Assembly Double Joint in the slot of the extrusion (B).
Place the extrusion (B) on the extrusion (A), then connect the pre-assembly insertion nut and screw to the double joint (1) by sliding them from both sides.
Tighten with a hex wrench while adjusting the position.
(Image of Inside of the Slot)
HFS6-3030-800-LSHExtrusion(B)
Extrusion(A)
7.329
7.9
16.5R4.25Ø5.2
1.9
12
4.7
4.7
R4.25Ø5
7.9
1.9
12
7.329
16.5 Ø10.9
7.329
7.9
16.5R4.25Ø5.2
1.9
12
4.7
4.7
R4.25Ø5
7.9
1.9
12
7.329
16.5 Ø10.9
(Ref.) Corner section when using this joint
QPre-Assembly Insertion Double Joint KitsPart Number Accessory Unit Price Volume Discount Rate
Type No. (1) Pre-Assembly Insertion Double Joint Quantity (2) Pre-Assembly Insertion Nut Quantity (3) Hex Socket Head Cap Screw Quantity 1~99 pc(s). 100~200 pcs.
HDJSN 6 HDJFSN6 6 HNTTSN6-5 2 SCB5-25 2
HDJHSN 6 HDJFSN6 6 HNTHSN6 2 SCB5-25 2
S Type Hole