black view car security camera
DESCRIPTION
Eagle eye technology (Hong Kong) Co., LtdURL:http://www.wholesalespycams.com http://onlinespycam.com http://onlinewholesalespycamera.comTRANSCRIPT
User manual V2.0
Thank you for purchasing BlackView.BlackView is a
portable, Stylish, high-performance vehicle drive
recorder. It has 5.0M effective pixel high-definition CMOS
image sensor, intelligent voice reminder, enhanced
night shooting,140°wide-angle lens.
Specific performance parameters are as follows:
CMOS sensor 5,000,000 pixels
Viewing angle of lens Wide-angle 140°
Turning angle of lens 200° back and forth
Screen 2.0TFT high resolution
Quality vedio HD(1280×720)@30fps
Night vision Enhanced night vision
Format of picture JPEG
Pixel of picture 2560x1920
Voice guidance intelligent voice guidance
Type of memory card TF card
Capacity of memory Card Supports up to 32G
Battery 800MA Polymer lithium battery
Power consumption 150MA
Check the product and the accompanied accessories
!
distributor.If there is any problem of the accessories, contact your local product
Checking the packing content
BlackView Support Slot
Power cable Driver disk
User m aualn Cable holders
Checking the main body of the BlackView
Lens
Enhanced night vision lightSpeaker
Vedio Play Camera
Microphone
Switching&Menu
TF Card Slot
USB Interface
TFT LCD
ResetSupport slot
1.Stop the engine and remove the key from the ignition.
Installing the BlackView
Install the BlackView in a well-lit and safe location.
2.Insert the Micro SD card into the BlackView.
3.Attach the BlackView into the windshield of your car using double-sided tape.Use a soft and dry cloth to wipe the foreign material and moisture attached in the surface of the support slot.
4.Connect the [USB] terminal of the BlackView and the cigarette jack of your car using the power cable.
5.Tie the power cableUse the provided cable holder, when necessary.
6.Adjust the position of the camera lens of the BlackView.
Ensure that it is level with the ground.
7.Start the engine. Check whether the BlackView is installed When the BlackVue is installed correctly, its Intelligent voice systems will play“The BlackView has been starting normal recording”.
Using the Normal Recording Function
Using the BlackView
Start the engine.BlackView turns on and starts the Normal Recording function. After it is turned on, it will records and saves scenes at each specified period.Stop the engine.BlackView will turn off after about 5 seconds.
Using the Manual Reconrding FunctionPress the <Switching> button on the BlackView.After BlackView turns on.Press the <Camera> button to starts the Manual Recording function. It will record and saves scenes at each specified period.Press the <Camera> button again.BlackView will exit
.Manual
Recording function
Using the Camera Function
Using the Playback Function
When BlackView turns on. To enter the Camera Function Press the <Camera> button.Press the <Camera> button again.BlackView will take photograph.
When BlackView turns on. Press and hold <Play> button for 2 seconds to enter the Playback Function.Press <Camera> or <Vedio>button to select the video or photo which you want,Then Press <Play> button to play.Press and hold <Play> button for 2 seconds again. The BlackView will exit the Playback Function.
Setting video output
Setting the BlackView
Video output including【Size】【EV】【White Balance】【Video Time】【Night Mode】
1.Setting 【Size】When System is turned on.Press <Switching> button to display video
output page.
Press <Camera> or <Vedio> button to select【Size】,Then Press
<Play> button to display Sub-page.
Sub-page including【VGA】【QVGA】【D1】【HD】,Press
<Camera> or <Vedio>button to select the setting which you want,Then
Press <Play> button to confirm.
2.Setting 【EV】
When System is turned on.Press < Switching > button to display video
output page.
Press <Camera> or <Vedio> button to select【EV】,Then Press <Play>
button to display Sub-page.
Sub-page including【+2.0】【+5/3】【+4/3】【+1.0】【+2/3】【+1/3】
【+0.0】【-1/3】【-2/3】【-1.0】【-4/3】【-5/3】【-2.0】,Press
<Camera> or <Vedio> button to select the setting which you want,Then
Press <Play> button to confirm.
O K Set
Size
White Balance
Vedio Time
Night Mode
HD
Auto
1 Min
O ff
Exit
Video output Setup
Q VGA
D1
EV +0.0
VGA
Setting the BlackView
3.Setting 【White Blance】When System is turned on.Press < Switching > button to display video output
page.
Press <Camera> or <Vedio> button to select【White Blance】,Then
Press <Play> button to display Sub-page.
Sub-page including【Auto】【Daylight】【Cloudy】【Tungsten】【
Fluorescent】,Press <Camera> or <Vedio> button to select the setting
which you want,Then Press <Play> button to confirm.
O K Set
White Balance
Size
Vedio Time
Night Mode
Auto
HD
1 Min
O ff
Exit
Video output Setup
Auto EV +0.0 Daylight
Tungsten
Cloudy
Fluorescent
O K Set
EV
White Balance
Vedio Time
Night Mode
+0.0
Auto
1 Min
O ff
Exit
Video output Setup
+0.0
Size HD +1/3
-2/3
-1.0
-1/3
Setting the BlackView
4.Setting 【Vedio Time】
5.Setting 【Night Mode】
When System is turned on.Press < Switching > button to display video
output page.
Press <Camera> or <Vedio> button to select【Night Mode】,Then
Press <Play> button to display Sub-page.
Sub-page including【Off】【On】,Press <Camera> or <Vedio> button
to select the setting which you want,Then Press <Play> button to
confirm.
O K Set
Video Time
White Balance
Size
Night Mode
1 Min
Auto
HD
O ff
Exit
Video output Setup
O ff
2 Min
EV +0.0 1 Min
When System is turned on.Press < Switching > button to display video
output page.
Press <Camera> or <Vedio> button to select【Night Mode】,Then
Press <Play> button to display Sub-page.
Sub-page including【Off】【On】,Press <Camera> or <Vedio> button
to select the setting which you want,Then Press <Play> button to
confirm.
Setting the BlackView
O K Set
Night Mode
White Balance
Vedio Time
O ff
Auto
1 Min
Exit
Video output Setup
O ff EV +0.0
Size HD
On
Setting SetupSetup including【Format】【beep】【language】【auto off】【sys.reset】【Light Freq.】【USB】【Screen Set】
1.Setting 【Format】Double click<Switching> button to display
Setup page.
Press <Camera> or <Vedio> button to select Format ,Then Press
<Play> button to display subpage.
Subpage including【Cancel】【Execute】,Press <Camera> or <Vedio>
button to select the setting which you want,Then Press <Play> button to
confirm.
When System is turned on.
【 】
O K Set
Format
Language
Auto Off
Beep
Next Menu
English
O ff
On
Exit
Video output
Cancel
Execute
Setup
Sys.Reset
Next Menu
Setting the BlackView
2.Setting 【Beep】
When System is turned on.Double click<Switching> button to display
Setup page.
Press <Camera> or <Vedio> button to select【Beep】,Then Press
<Play> button to display subpage.
Subpage including【On】【Off】,Press <Camera> or <Vedio> button to
select the setting which you want,Then Press <Play> button to confirm.
3.Setting 【Language】When System is turned on.Double click<Switching> button to display
Setup page.
Press <Camera> or <Vedio> button to select【Language】,Then
Press <Play> button to display subpage.
Subpage including【English】【繁體中文】【简体中文】【日本語】【
Русский】,Press <Camera> or <Vedio> button to select setting
which you want,Then Press <Play> button to confirm.
O K Set
Beep
Language
Auto Off
Format
On
English
O ff
Next Menu
Exit
Video output
On
O ff
Setup
Sys.Reset
Next Menu
Setting the BlackView
O K Set
Language
Format
Auto Off
Beep
English
Next Menu
O ff
On
Exit
Video output
English
Setup
Sys.Reset
Next Menu
简体中文
日本語
Русский文
4.Setting 【Auto Off】
When System is turned on.Double click<Switching> button to display
Setup page.
Press <Camera> or <Vedio> button to select【Auto Off】,Then Press
<Play> button to display subpage.
Subpage including【1 Min】【3 Min】【5 Min】【Off】,Press
<Camera> or <Vedio> button to select the setting which you want,Then
Press <Play> button to confirm.
O K Set
Auto Off
Format
Language
Beep
O ff
Next Menu
English
On
Exit
Video output
1 Min
Setup
Sys.Reset
Next Menu
3 Min
5 Min
Off
Setting the BlackView
5.Setting 【Sys.Reset】
When System is turned on.Double click<Switching> button to display
Setup page.
Press <Camera> or <Vedio> button to select【Sys.Reset】,Then
Press <Play> button to display subpage.
Subpage including【Cancel】【Execute】,Press <Camera> or
<Vedio> button to select the setting which you want,Then Press <Play>
button to confirm.
6.Setting 【Light Fre.】
When System is turned on.Double click<Switching> button to display
Setup page.
Press <Camera> or <Vedio> button to select【Light Fre.】,Then Press
<Play> button to display subpage.
Subpage including【60Hz】【50Hz】,Press <Camera> or <Vedio>
button to select the setting which you want,Then Press <Play> button to
confirm.
O K Set
Sys.Reset
Beep
Auto off
Language
Next Menu
Language
Light Freq.
Date Input
Exit
Video output
Cancel Execute
Format
Next Menu
Setup
Setting the BlackView
O K Set
Light Freq.
USB
Screen Set
60Hz
PC Cam
Aways On
Exit
Video output
60Hz 50Hz
Setup
7.Setting 【USB】
When System is turned on.Double click<Switching> button to display
Setup page.
Press <Camera> or <Vedio> button to select【Light Fre.】,Then Press
<Play> button to display subpage.
Subpage including【60Hz】【50Hz】,Press <Camera> or <Vedio>
button to select the setting which you want,Then Press <Play> button to
confirm.
O K Set
USB
Light Freq.
Screen Set
PC Cam
60Hz
Aways On
Exit
Video output
PC Cam Disk Drive
Setup
Setting the BlackView
8.Setting 【Screen Set】
When System is turned on.Double click<Switching> button to display
Setup page.
Press <Camera> or <Vedio> button to select【Screen Set】,Then
Press <Play> button to display subpage.
Subpage including【Always On】【1 Min】【3 Min】,Press
<Camera> or <Vedio> button to select the setting which you want,Then
Press <Play> button to confirm.
O K Set
Screen Set
Light Freq.
USB
Aways On
60Hz
PC Cam
Exit
Video output
Away On 1 Min
Setup
Ballasoft