basic introduction chlor rid (1)

10
Removing Soluble Salts Protects Your Assets More Economically than Other Initiatives REGIS DOUCETTE CHLOR RID, INTERNATIONAL (201) 664 5487 [email protected]

Upload: harishharry-sharma

Post on 07-Aug-2015

68 views

Category:

Technology


3 download

TRANSCRIPT

Page 1: Basic introduction chlor rid (1)

Removing Soluble Salts Protects Your Assets More Economically than Other Initiatives

REGIS DOUCETTE

CHLOR RID, INTERNATIONAL

(201) 664 5487 [email protected]

Page 2: Basic introduction chlor rid (1)

Soluble Salts Are Everywhere But Should Not Be Allowed on Certain Parts of YOUR AssetsOne key statistic from trade association, SSPC, revealed that 80% of all coating failures were attributable to bad surface preparation. A separate survey said that 80% of bad surface preparation was a consequence of soluble salts. This equates to the notion that 64% or two-thirds of all coating failures are related to avoidable soluble salt contamination.

Page 3: Basic introduction chlor rid (1)

Nature of the Beast—What are Soluble Salts Ionic contaminants (like dust particles that interfere with adhesion, accelerate

corrosion, cause blistering, and allow disbondment of protective coatings such as insulation or fire resistant coatings)

Water soluble inorganic compounds (humidity triggers the electrolyte portion of the “corrosion cell” that is the mechanism for corrosion)

Primarily chlorides, sulfates, and nitrates (that convert to hydrochloric, sulfuric, and nitric acids on metals which explains why rust “corrodes” metals)

Non-visible contaminants (shown in detail on next slide which illustrates why ion specific and real test kits are required for assessment before and after remediation)

Can bond electrochemically to the metal substrate (which is why a chemical is needed to remediate and not just mechanical abrasion)

Page 4: Basic introduction chlor rid (1)

Soluble Salts Are Non-Visible at One Millionth the Size of a Sand Particle

40 mil

The “gold” standard in protective coatings standards is the white metal blast “appearance” for surface cleanliness. However, that is based on visible to the naked eye assessment. Here we see proof that this serious contaminant makes what is “pretty”, not so pretty!!!

Page 5: Basic introduction chlor rid (1)

Visible Corrosion On Untested/Untreated Soluble Salt Contaminated Surfaces (4 days!!)

Page 6: Basic introduction chlor rid (1)

Why use CHLOR RID to test for Soluble Salts

Field proven for more than two decades, premeasured elements of the test kits accurately and quickly reveal the ion specific contamination levels. Different salts have different corrosivities with different allowable thresholds

Testing after cleaning assures the proper level of cleanliness is attained. Consumable components assure no cross-contamination Major scientific laboratories buy and use our test kits including Federal

Highway Authority for their reliability in replicating results. Specifications specifically call out for our CSN test kit for chlorides, sulfates, and

nitrates for different authorities including US Navy Facilities Command and US Army Corps of Engineers. http://www.wbdg.org/ccb/DOD/UFGS/UFGS%2009%2097%2013.27.pdf

Page 7: Basic introduction chlor rid (1)

Why Use CHLOR RID Soluble Salt Remover

Assures proper surface preparation and is viewed as Best Management Practice

Helps prevent premature coating failures and works with all coating systems

Extends life of coating system with significant economic advantages (next slide)Added to potable wash water to remove soluble salts from the surfaces with normal equipment.

Offers DUAL FUNCTION CHEMISTRY that 1. Chelates the metal cations and 2. Sequesters the salt anions

Biodegradable (when tested for LDL, lethal dose limit, it was not tested in the 1 to 100 ratio as intended to be used, but accidentally was tested at FULL concentrated strength, and still passed.)

Cost effective at about ten cents per sq ft plus a second dime approximation for test kits, that favorably compares with other preparation costs which do not remove soluble salts as readily and cost $/sq ft.

Page 8: Basic introduction chlor rid (1)

“Prior to 1995, it is estimated that at least 3 out of 4 contractors suffered major failures during projects or shortly thereafter. Most coatings did not survive more than 5 to 7 years. Now with changes, including CHLOR*RID, we have an approximately 70 to 90% reduction in lifecycle costs, have reduced premature coating failures and increased service life.”

--source, NAVFAC

Page 9: Basic introduction chlor rid (1)

How You Can Help Preserve Your Assets and Optimize Your Construction Dollars

Engineering staff (internal and outsourced) can update specifications for surface preparation sections and concrete repairs (inspired by successful private industry, SSPC, NACE, AREMA, US D.O.D.,) Project staff on projects can implement Best Management Practices of testing for and removing soluble salts (various references worldwide)Maintenance staff periodically maintenance wash surfaces to remove surface salts (inspired by various Transportation Departments and professional practices, e.g W VA DOT and W VA Pkwy. Auth.)

Page 10: Basic introduction chlor rid (1)

End NotesSSPC: The Society for Protective Coatings, Technology Guide 15, Field Methods for Extraction and Analysis of Soluble Salts on Steel and Other Nonporous Substrates, www.sspc.org/market-place/standardsNACE: National Association of Corrosion Engineers, NACE Report 6G186, Surface Preparation of Soluble Salt Contaminated Steel Substrates Prior to Coating, http://web.nace.org/Departments/Store/Search.aspx More info at www.chlor-rid.com (made in America)[email protected] (but prefer…. [email protected] where file size not matter)