basic calibration - endress
TRANSCRIPT
11/12/2019
Products Solutions Services
Basic Calibration
Slide 1 / 36 Service SC-TH
11/12/2019
What is the calibration ?
Basic Calibration
Slide 2 / 36 Service SC-TH
11/12/2019
Basic terms in metrology
Accuracy
It is a qualitative expression for the closeness of the measured
value to the true value.
Specification
Basic Calibration
Slide 3 / 36 Service SC-TH
11/12/2019
Repeatability
• Closeness of the agreement between the results of successive measurements of
the same measurand carried out under the same conditions of measurement
A B
DC
High accuracy = good repeatability (A),
but good repeatabilitydoes not necessarily mean high accuracy (C)!
Basic Calibration
Slide 4 / 36 Service SC-TH
11/12/2019
Factory Calibration
• Calibration is the last stage of production and quality assurance
• All new flowmeters are calibrated and adjusted
• Adjustment between measurement result and specification
• Electronic correction at two points (zero/max)
• At zero zero point adjustment
• At max calibration factor
Basic Calibration
Slide 5 / 36 Service SC-TH
11/12/2019
Factory calibration of flowmeters
• During calibration, a fluid flows through the device under test.
• The output signal of the device under test is compared to the signal of a reference (scales,
volume, master) and any deviation is determined.
• The measurement result is indicated on a calibration certificate (SCS) provided with the
instrument (paper) and on a CD; and archived in a database.
Basic Calibration
Slide 6 / 36 Service SC-TH
11/12/2019
Three calibration methods
Calibrated volume Calibrated scales
1) Volumetric 2) Gravimetric
Basic Calibration
Slide 7 / 36 Service SC-TH
11/12/2019
Three calibration methods
Water reservoir
Device under test
Ma
ste
r in
stru
me
nts
Constant flow
oCComputer
Temperature and time
3) Master calibration
Fre
qu
en
cy
Fre
qu
en
cy
Basic Calibration
Slide 8 / 36 Service SC-TH
11/12/2019
What’s all the hype about?
• What is the benefit of a worldwide calibration concept?
By providing a worldwide calibration concept our customers are assured that
their flowmeter are always calibrated to the same perfection independent of the
manufacturing site.
This is also important for all recalibration and verification services performed at
our manufacturing sites.
• What is the benefit of a traceable calibration?
Only traceability ensures that the calibration is verified against the relevant
national standard.
Additionally we are the only flowmeter manufacturer offering compliance to the
international standard ISO 17025 for all calibration rigs.
Basic Calibration
Slide 9 / 36 Service SC-TH
11/12/2019
What’s all the hype about?
• What is the benefit of an accreditation?
Accreditation means the formal recognition of the technical and organizational
competence of E+H to execute calibration services as described in the scope of
accreditation. Competence is the key to transparency, confidence and
comparability.
Accreditation means that the performance and traceability of our calibration
rigs are regularly supervised by the relevant national accreditation authority
(i.e. third-party approval).
Basic Calibration
Slide 10 / 36 Service SC-TH
11/12/2019
What influences the accuracy of a Coriolis flow meter
• Density and viscosity of liquid is different from the liquid used for calibration
=> can be compensated by zero point adjustment
• Disbalances of the measuring system due to coating or abrasion
=> can be compensated by zero point adjustment
• Operating pressure different from pressure at calibration
=> effect is very small and pressure compensation possible
• Operating temperature different from temperature at calibration
=> compensate by zero point adjustment.
• Pipe line loads might deform the measuring system and influence the accuracy
of the meter
• Disbalances of measuring system by entrained gas.
=> effect is erratic no real compensation possible.
Basic Calibration
Slide 11 / 36 Service SC-TH
11/12/2019
Total Accuracy Promass 80E DN 50
Measured Flowrate = 15’000kg/hZero point stability = 7 kg/h temperature error = 5.6kg/h
Total accuracy = ±0.3% ± 7/15000*100 ± 5.6/15000*100
Total accuracy = ±0.3% ± 0.045% ± 0.036%= 0.381%
Basic accuracy Zero point + temperature effect
Basic Calibration
Slide 12 / 36 Service SC-TH
11/12/2019
Overview Flow Calibration for SC-TH
Basic Calibration
Slide 13 / 36 Service SC-TH
11/12/2019
Basic Calibration
Slide 14 / 36 Service SC-TH
11/12/2019
Basic Calibration
ชนิดของงาน Calibration Flowmeter
• 1. การสอบเทียบดว้ย Field Check (Verification)
• 2. การสอบเทียบดว้ย Ultrasonic Clamp-on Flowmeter
• 3. Wet Calibration ดว้ย Mobile Calibration Rig
Slide 15 / 36 Service SC-TH
11/12/2019
การสอบเทยีบ Flowmeter ด้วย FieldCheck หรือ Dry Calibration
Basic Calibration
กล่อง Simubox
Massmeter Field Check
Flowmeter
ที�ต้องการสอบเทียบ
Outputs cable
Service interface cable
Slide 16 / 36 Service SC-TH
11/12/2019
Service
Basic Calibration
• Service connection for Promag 50, 53, Promass 80,83
•
Slide 17 / 36 Service SC-TH
11/12/2019
Basic Calibration
Fieldcheck - Verification results
• หนา้จอการสอบเทียบ Flowmeter ดว้ย FieldCheck
• การแสดงผลหลงัการสอบเทียบ
Passed Failed
Slide 18 / 36 Service SC-TH
11/12/2019
การโหลดข้อมูลจาก FieldCheck เพื�อออกใบ Certificate
Basic Calibration
FieldCheck
FieldTool
• Workshop operation
• Field operation
Slide 19 / 36 Service SC-TH
11/12/2019
หน้าตาของใบ Verification Certificate โดย FieldCheck
Basic Calibration
Slide 20 / 36 Service SC-TH
11/12/2019
Basic Calibration
การสอบเทยีบ (Verify) หรือ Dry Calibration ด้วย FieldCheck
• Reference Accuracy : ±0.5%
• ขอ้ดีและประโยชน์ของการสอบเทียบ
• สะดวก ไม่ตอ้งถอดมิเตอร์
• บนัทึกผลและทาํเอกสารอติัโนมติั
• เครื�องมือ สามารถสอบกลบัได้
• มีการตรวจสอบเสถียรภาพการทาํงานของเครื�อง
• ไดเ้อกสาร Certificate
Slide 21 / 36 Service SC-TH
11/12/2019
Basic Calibration
การสอบเทยีบ (Verify) หรือ Dry Calibration ด้วย FieldCheck
• ขอ้จาํกดั
• เป็นการสอบเทียบ (Verify)
• สอบเทียบไดเ้ฉพาะ Flowmeter ของ E+H
• ระยะเวลาการปฏิบติังาน
• ประมาณ 30 -40 นาทีต่อเครื�อง หรือนอ้ยกวา่
• ค่าใชจ่้าย
• ประมาณ 3,000 บาทต่อเครื�องในเขตกรุงเทพและปริมณฑล(ไม่เกิน 150 กม)
• ต่างจงัหวดั คิดค่าเดินทางเพิ�มตามระยะทาง
Slide 22 / 36 Service SC-TH
11/12/2019
Basic Calibration
การสอบเทยีบ (Verify) หรือ Dry Calibration ด้วย FieldCheck
• การเลือกใชง้าน
• ใชส้อบเทียบมิเตอร์ที�ใชใ้นงานควบคุม Process ทั�วไป ที�ไม่ไดต้อ้งการความถูกตอ้งแม่นยาํสูงเป็นพิเศษ
• ใชต้รวจสอบมิเตอร์เพื�อทราบวา่อยูใ่นสภาพสมบูรณ์หรือไม่
• ใชส้อบร่วมกบัวธีิการอื�นเพื�อความมั�นใจ
Slide 23 / 36 Service SC-TH
11/12/2019
การสอบเทยีบ (Verify) โดย Ultrasonic Clamp-on Flowmeter
Basic Calibration
Slide 24 / 36 Service SC-TH
11/12/2019
การสอบเทยีบ (Verify) โดย Ultrasonic Clamp-on Flowmeter
Basic Calibration
Slide 25 / 36 Service SC-TH
11/12/2019
Basic Calibration
การสอบเทยีบ (Verify) โดย Ultrasonic Clamp-on Flowmeter
• Reference Accuracy : ประมาณ ±2.0% (ขึ�นกบัสภาพของจุดตั�ง)
• ขอ้ดีและประโยชน์
• สะดวก ไม่ตอ้งถอดมิเตอร์ที�ตอ้งการสอบเทียบ
• ติดตั�งง่าย โดยรัดกบัท่อ
• สอบเทียบ Flowmeter ไดทุ้กยี�หอ้
• สอบเทียบ Flowmeter ไดต้ั�งแต่ท่อขนาด DN15 ถึง DN4000
• ไดเ้อกสาร Certificate
Slide 26 / 36 Service SC-TH
11/12/2019
Basic Calibration
การสอบเทยีบ (Verify) โดย Ultrasonic Clamp-on Flowmeter
• ขอ้จาํกดั
• ของเหลวในท่อและตวัท่อตอ้งอยูใ่นลกัษณะที�มิเตอร์วดัได้
• ทดสอบไดเ้ฉพาะอตัราเร็วการไหลที�มีอยูใ่นท่อ
• ระยะเวลาการปฏิบติังาน
• ประมาณ1 ชั�วโมงต่อจุด หรือนอ้ยกวา่
• ค่าใชจ่้าย
• ขึ�นอยูก่บัสภาพความยากง่ายของการติดตั�งและระยะเวลาที�ตอ้งการทดสอบ โดยทั�วไปประมาณ 4,000 บาทต่อจุด (ไม่รวมค่าเดินทาง)
Slide 27 / 36 Service SC-TH
11/12/2019
Basic Calibration
การสอบเทยีบ (Verify) โดย Ultrasonic Clamp-on Flowmeter
• การเลือกใชง้าน
• ใชส้อบเทียบมิเตอร์วดันํ�าที�มีขนาดใหญ่
• ทดสอบมิเตอร์ทั�วไป ที�ไม่ตอ้งการความแม่นยาํสูงมาก
• ใชว้ดัทดสอบหาประสิทธิภาพของระบบปั�มต่างๆ
• วดัหาอตัราการไหลตามท่อต่างๆในโรงงานโดยไม่ตอ้งตดัต่อท่อ
Slide 28 / 36 Service SC-TH
11/12/2019
การทาํ Wet Calibrate ด้วย Mobile Test Rig
Basic Calibration
Slide 29 / 36 Service SC-TH
11/12/2019
การทาํ Wet Calibrate ด้วย Mobile Test Rig
Basic Calibration
Slide 30 / 36 Service SC-TH
11/12/2019
การทาํ Wet Calibrate ด้วย Mobile Test Rig
Basic Calibration
Slide 31 / 36 Service SC-TH
11/12/2019
หากต้องการ Lab ที�ได้รับการการรับรองจาก ISO17025 ต้องส่งอุปกรณืมาที� Lab E+H
Basic Calibration
Slide 32 / 36 Service SC-TH
11/12/2019
Basic Calibration
การทาํ Wet Calibrate ด้วย Mobile Test Rig
• Reference Accuracy : ประมาณ ±0.05% (liquid), ±0.35% (gas)
• ขอ้ดีและประโยชน์
• มิเตอร์มาตรฐานที�ใชอ้า้งอิง มีความแม่นยาํสูง
• สอบเทียบ Flowmeter ไดทุ้กยี�หอ้
• สามารถสอบเทียบ Flowmeter นอกสถานที�ได้
• ไดเ้อกสาร Certificate
Slide 33 / 36 Service SC-TH
11/12/2019
Basic Calibration
การทาํ Wet Calibrate ด้วย Mobile Test Rig
• ขอ้จาํกดั
• ตอ้งถอดมิเตอร์ออกมาสอบเทียบขา้งนอก หากไม่มีจุดบายพาส
• ใชเ้วลามากในการสอบเทียบแต่ละจุด
• ระยะเวลาการปฏิบติังาน
• ประมาณ 2 ถึง 4ชั�วโมงขึ�นกบัสภาพหนา้งานและจาํนวนจุดที�ตอ้งการทดสอบ
• ค่าใชจ่้าย
• ขึ�นอยูก่บัสภาพความยากง่ายของการติดตั�ง โดยทั�วไปประมาณ 10,000 บาทต่อตวั ต่อการสอบเทียบ 1 point ในกรุงเทพและปริมนฑล (ต่างจงัหวดัคิดค่าเดินทางเพิ�มตาม
ระยะทาง) point ต่อไปคิดเพิ�ม 3,500 บาท/point
Slide 34 / 36 Service SC-TH
11/12/2019
Basic Calibration
การทาํ Wet Calibrate ด้วย Mobile Test Rig
• การเลือกใชง้าน
• ใชส้อบเทียบ Flowmeter ที�ตอ้งการความแม่นยาํสูง
• เพื�อทาํตารางถงั (Tank Table) โดยการตวงปริมาณนํ�าเทียบกบั Flowmeter
Slide 35 / 36 Service SC-TH
11/12/2019
Questions
Basic Calibration
Slide 36 / 36 Service SC-TH