b44.1 manual preflight

38
9/10

Upload: cristian-enache

Post on 28-Apr-2015

101 views

Category:

Documents


6 download

TRANSCRIPT

Page 1: b44.1 Manual Preflight

9/1

0

Page 2: b44.1 Manual Preflight

2:: Introduction

:: KIT Features

:: Additional Features

:: Other Helpful Items

Associated Electrics, Inc.26021 Commercentre Dr.Lake Forest, CA 92630

http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook

Customer ServiceTel: 949.544.7500Fax: 949.544.7501

Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new RC10 B44.1. Please take a moment to read through this manual to help familiarize yourself with these steps.

We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the illustra-tions. New parts will be noted on supplementary sheets located in the appropriate parts bags. Check each bag for these sheets before you start to build.

The Factory Team B44.1 is the next generation in a long line of race winning 10th scale 4wd buggies dating back to 2003. The B44 project came to life as a cooperative effort between Team Associated and J Concepts’ Jason Ruona and Brad Reelfs, culmi-nating with Team Associated driver Ryan Cavalieri winning the 2005 I.F.M.A.R. World Championships in Italy with the BJ4 World’s Edition. The production B44 Factory Team continued the winning ways with Jared Tebo winning the 2007 I.F.M.A.R. World Cham-pionship in Japan along with Ryan Maifield and Ryan Cavalieri in a 1-2-3 B44 podium sweep.

Team Associated designers optimized the B44.1 for the latest generation of racers using LiPo batteries and brushless motors. With the advent of this new technology, R/C cars are lighter and more powerful than ever. The B44.1 is geared for strictly LiPo batter-ies, with no cell slots in the chassis and a carbon fiber battery tray as standard equipment. The center section of the battery tray can be replaced with an optional (not included) ballast weight for more rearward weight bias. Motor installation and adjustment is a breeze thanks to the cam motor mount system. The blue aluminum rear hubs add durability and new camber link adjustment options. Lastly, the B44.1 comes with the latest JConcepts Punisher body and under tray.

Features in the B44.1 Factory Team:• 2.5mm updated carbon fiber chassis for LiPo batteries only• Carbon fiber LiPo battery tray with removable center section (*optional ballast weight req’d)• 3.5 mm front shock tower• Updated front top deck for more durability along with new antenna location• Cam motor mount set• Factory Team 0 degree aluminum rear hubs with oversize outer bearing.• Factory Team V2 dual-cap hard anodized shock bodies with threaded collars• V2 slipper assembly with high-rate spring • Factory Team Gold slipper pads• JConcepts Punisher body and under tray• Pro-Line M3 Holeshot 2.0 tires• Rear anti-roll bar included• Bleed-screw shock caps• TiN “Gold” shock shafts front and rear• Carbon fiber battery straps with thumb screws• 1/4” locking and 3/16” mini locking nuts

B44.1 F.T. Additional Kit Features:• Servo mounted 3mm closer to centerline • Chassis cut for additional ground clearance• Ball differential with light-weight outdrives • Dual-sided externally adjustable slipper clutch• CVA joints with pin retainer clips • Factory Team blue Titanium turnbuckles• Factory Team blue aluminum servo mounts • Factory Team blue aluminum wheel spacers• Factory Team blue aluminum shock bushings • Factory Team blue aluminum shock pivot balls• Ball-bearings steering bell cranks • Fully adjustable camber, and toe-in• Built in servo saver • Vertical ball end adjustment front & rear

• Silicone Shock Fluid (Refer to catalog for complete listings)• Body Scissors (AE Part # 1737) • Reamer / Hole Punch • Wire Cutters • Hobby Knife • FT Hex Wrenches (AE Part # 1541) • Needle Nose Pliers • Multi Tool (AE Part #7494)• Soldering Iron • Calipers or a Precision Ruler • Green Slime shock lube (AE Part # 1105)

Page 3: b44.1 Manual Preflight

3:: Table of Contents

:: Notes

This symbols indicates a special note or instruction in the manual.

!There is a 1:1 hardware foldout page in the back of the manual. To check the size of a part, line up your hardare with the correct drawing until you find the exact size. Each part in the foldout has a number assigned to it for ordering replacement parts.

1....................Cover

2....................Introduction 3....................Table of Contents

4....................Front / Rear Differential Build

5....................Front Gearbox Build

6....................Rear Gearbox Build

7 - 8..............Steering and Center Battery Brace Build / Install

8 - 9..............Front End Build

9....................Rear End Build

10.................Slipper Build

11..................Center Bulkhead Mounts

11.................Front Top Deck Build

11-12..........Rear Top Deck Build

13.................Turnbuckles Build

13.................Front CVA Build

13-14..........Front Suspension Build

15.................Rear CVA Build

15 - 16.......Rear Suspension Build

16-17..........Rear Anti-Roll Bar Build

17.................Battery Tray and Side Body Mounts Build

18 - 19........Shocks Build

19 - 20........Servo Build

20.................Electronics Install

21 - 22........Body, Wheel, Tires Install

23 - 24.........Tuning Tips

25-33.........Catalog

34.................Notes

35.................Setup Sheet “Kit Setup”

36.................1:1 Hardware “Fold Out”

37.................Setup Sheet “Blank”

38.................Back Cover

Associated Electrics, Inc.26021 Commercentre Dr.Lake Forest, CA 92630

http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook

Customer ServiceTel: 949.544.7500Fax: 949.544.7501

Page 4: b44.1 Manual Preflight

4:: Front and Rear Differential Build - Step 1

:: Front and Rear Differential Build - Step 2

-1/8

-5/8

-1/4

-3/8

0

-1/4 -3/4

5/64” hex wrenchinstalled in diff bolt

Fully tightened

position

KitSetting

Trim any flashing material off of the

#2330 Locking t-nut ears!

!

Build twodiffs!

!

#65

88

blac

k gr

ease

3911Diff outdrive

shim

3976Diff outdrive

bearing

6574Thrust balls

6582Diff

spring

2330Locking

t-nut

6573Thrust

washers

6573Thrust screw

6909Diff

bearing

x6

x2

x6

x2

6909Diff

bearing

3914Bevel

diff gear

9734Diff

outdrive, long

9734Diff

outdrive, short

6579Diff

outdrive ring

6579Diff

outdrive ring

6581Diff balls

x12

#6591diff lube

#6591diff lube

#6591diff lube

Page 5: b44.1 Manual Preflight

5:: Front Gearbox Build - Step 1

:: Front Gearbox Build - Step 2

:: Front Gearbox Build - Step 3

6860FT 4-40x3/8”

shcs aluminum, blue

Align the gap in the pin retainer

to be opposite of the CVA pin.

Racer’s Tip:Try using only 1 drop of CA glue

to secure the pin retainer!

Trim flashing off back of gear. Align the slot in the pinion gear

with the pin!

!

!

#1597ca glue

39773/16x3/8”

bearing

3911Drivetrain

shim

x2

x2

x6

#6591

diff lube

#6588

black grease

9733Upper

transmission case

6299E-clip

3919Input shaft

pin

3903Shaft pinion

gear

7996CVA pin retainer

73814-40

setscrew

9761CVA input

shaft

7381CVA

coupler

9747CVA bone

center, front

9733Lower

transmission case

#6591

diff lube

1 drop!1 drop!

1 drop!

Page 6: b44.1 Manual Preflight

6:: Rear Gearbox Build - Step 1

:: Rear Gearbox Build - Step 2

:: Rear Gearbox Build - Step 3

39773/16x3/8”

bearing

3911Drivetrain

shim

x2

x2

6860FT 4-40x3/8”

shcsaluminum,

blue

#6591

diff lube

#6591

diff lube

#6588

black grease

x6

9733Upper

transmission case

6299E-clip3919

Input shaft pin

3903Shaft pinion

gear

7996CVA pin retainer

73814-40

setscrew

9761CVA input

shaft

7381CVA

coupler

9760CVA bone

center, rear

9733Lower

transmission case

Align the gap in the pin retainer

to be opposite of the CVA pin.

!

#1597ca glue

Align the slot in the pinion gear

with the pin!

!with the pin!

Racer’s Tip:Try using only 1 drop of CA glue

to secure the pin retainer!

1 drop!

1 drop!

1 drop!

Page 7: b44.1 Manual Preflight

7:: Steering and Center Battery Brace Build Step 1

:: Steering and Center Battery Brace Build Step 2

9746Steeringbearing

set

:: Steering and Center Battery Brace Build Step 3

1mm

9746Steeringbearing

set

6272Foam dust

cover

9630.030” washer

9743Spring

retainer

9743Steeringv-spacer

9743Servo saverupper

6277Ballstud

long, silver

x2

x2

x2

x2

x2

62924-40x3/8”

fhcs

9774B44.1 LiPo

chassis

9743Steering retainer column

9743Steering

retianer top

62924-40x3/8”

fhcs

69174-40x3/8”

bhcs

3874Black carrier

bushing

97445-40

locknut

9744Servo saver

spring

9743Servo saver

lower

6272Dust cover

foam6276

Ballstudshort, silver

9743Steering

rack

x2x2

x2

x2

9744Steering

post

x2

x2

Use the large hole bearings!

Use the small hole bearings!

!

!

Page 8: b44.1 Manual Preflight

8:: Steering and Center Battery Brace Build / Install Step 4

:: Front End Build - Step 1

:: Front End Build - Step 2

9715Front arm

9714Shock tower

mounts

96452-56x1/8”

bhcs

62924-40x3/8”

fhcs

62924-40x3/8”

fhcs

62924-40x3/8”

fhcs

6472Shock

mount nuts

9775B44.1 LiPobattery tray

9716Front innerhinge pin

44494-40x3/16”aluminum

locknut

9713Front

bulkhead

97654-40x7/16”

fhcs

x2

x2x2

x2

x2

x2

x2

#1596thread lock

Page 9: b44.1 Manual Preflight

9:: Front End Build - Step 3

:: Rear End Build - Step 1

:: Rear End Build - Step 2

69154-40x5/8”

fhcs

1780Shock

bushing

9703Front shock

tower

74134-40x3/4”

bhcs

9726Rear chassis

brace

96452-56x1/8”

bhcs6292

4-40x3/8”fhcs

9716Rear innerhinge pin

44494-40x3/16”aluminum

locknut

44494-40x3/16”aluminum

locknut

6936#4 washer

69174-40x3/8”

bhcs

69174-40x3/8”

bhcs

9718Front

bumper

9764Rear arm

9718Rear

bumper

9726Rear

chassisplate

97654-40x7/16”

fhcs

76734-40x5/16”

fhcs

x2x4

x2

x3

x2

x2x2

x2

x2

x2

x2

#1596thread lock

Page 10: b44.1 Manual Preflight

10:: Slipper Build - Step 1

:: Slipper Build - Step 2

:: Slipper Build - Step 3

x2

x2

Check slipperafter running!

Adjust as needed.

!

1654Solid pin

9742Slipper drive

cup

9742Slipper drivecup o-ring

1654Solid pin

9711Center bearing

insert7485FT V2

slipper hubs

73814-40

setscrew

Side view1 flange

9741Slipper nut

o-ring9740Slipper

nut

7486FT V2

slipper spring

9742Slipper drive

cup

9736Slipper shaft

9736Slipper spring

retainer

9711Center

bearing insert

9736slipper

drive cup spacer

79353/16x1/2”

bearing

9603Slipper

pad

965181T 48Pspur gear

79353/16x1/2”

bearing

x2

10mm

Side view2 flanges

#6588black grease

Rub black grease on o-ring before

install!

Insert #9741 Slipper nut o-ring all the way into the

#9740 Slipper nut be-fore installing the slipper nut to the slipper shaft!

!

!

Page 11: b44.1 Manual Preflight

11:: Center Bulkhead Mounts - Step 1

:: Front Top Deck Build - Step 1

:: Front Top Deck Build - Step 2 :: Rear Top Deck Build - Step 1

Key CVA bones in the slipper outdrives!

Set remaining motor mount pieces aside!

!

!

31113Antenna mount

9714Shock tower mount

9701Top deck

front

9719Body

mount

9709Center

bulkhead

9801FT cam motor mount

43342-56x5/16”

bhcs

69174-40x3/8”

bhcs

69174-40x3/8”

bhcs

6277Ballstud

long, silver

44494-40x3/16”aluminum

locknut9702

Top deckrear

6936Washers,

aluminum #4

x2

x2

x2

x2

Top deckfront

Body mount

x2

x29714Shock tower mount

bhcs

6917 x2x2

44494-40x3/16”aluminum

locknut

6936Washers,aluminum

#4

62924-40x3/8”

fhcs

62914-40x1/4”

fhcs

6277Ballstud

long, silver

x2

x2

x3

x262884-40x1/4”

bhcs

Slipper assembly

Install

#1596

thread lock

62924-40x3/8”

fhcs

x5#1596

thread lock

Page 12: b44.1 Manual Preflight

12:: Rear Top Deck Build - Step 2

:: Rear Top Deck Build - Step 3

:: Rear Top Deck Build - Step 4

74134-40x3/4”

bhcs1780Shock

bushing

62924-40x3/8”

fhcs

9719Body mounts

x2

x2

x2

69174-40x3/8”

bhcs

77384-40x7/8”

shcs

69254-40x1/2”

shcs

69174-40x3/8”

bhcs

69244-40x3/8”

shcs

69244-40x3/8”

shcs

9712Center

bulkhead cap

9704Shock tower

rear

9714Shock tower

mount

9729Wing mount(right, left) 4449

4-40x3/16”aluminum

locknut

x2

x2

x3

x2

x2

x4

x2

#1596thread lock

#1596thread lock

#1596thread lock

Page 13: b44.1 Manual Preflight

13:: Turnbuckles Build - Step 1

:: Front CVA Build - Step 1

:: Front Suspension Build - Step 1

Front Steering Link

Front Camber Link

Rear Camber Link

44494-40x3/16”aluminum

locknut

9722Steering

block(right, left)

6277Ballstud

long, silver

6272Foam dust

cover

x2

x2x2

x2

Align the gap in the pin retainer

to be opposite of the CVA pin.

!

SteeringBuild x2

Front CamberBuild x2

Rear CamberBuild x2

Build x2

1 drop!

7996CVA pinretainer

7381CVA cross

pin

7381CVA coupler

1406FT titaniumturnbuckles

2.00”

1406FT titaniumturnbuckles

2.00”

1404FT titaniumturnbuckles

1.77”

9748CVA axle

front

9747CVA bone

front

#65

88

blac

k gr

ease

39773/16x3/8”

bearing

x4

9751Bearing

crush tube

x2

Left Side

Left Side

Right Side

Right Side

7230Ball cups,

large

7230Ball cups,

large

7230Ball cups,

large

x2

x2

x2

67mm

60mm

64.5mm

#1597ca glue

Page 14: b44.1 Manual Preflight

14:: Front Suspension Build - Step 2

:: Front Suspension Build - Step 3

:: Front Suspension Build - Step 4

22214-40x7/16”

bhcs

7369Axle pin

9647Steering

block bushing

6272Dust cover

foam

9750Axle drive

hex

44494-40x3/16”aluminum

locknut

9720Caster block(right, left)

3983Ballstud

long, black

x2

x2

x2

x2x2

x4

x2

x4

Left Side

Left Side

Left Side

Left Side

Right Side

Right Side

Right Side

Right Side

96452-15x1/8”

bhcs

Build x2 (right and left side)

9716Hinge pin

set

Front camber

link

Front steering

link

Install x2 (right and left side)

Orient the notch to the left

throughout the car. It indicates

which end has the left hand threads!

!

Page 15: b44.1 Manual Preflight

15:: Rear CVA Build - Step 1

:: Rear Suspension Build - Step 1

:: Rear Suspension Build - Step 2

39773/16x3/8”

bearing

7381CVA coupler 7996

CVA pinretainer

9755CVA axle

rear

9872FT aluminum

hub tower(A)

9864FT aluminum

hub (0˚)

9754CVA bone

rear7381

CVA cross pin

6272Dust cover

foam

7933Crush tube

3983Ball stud

long (black)

x2

x2

x2

x2

x2

69324-40x5/16”

shcs

7935.187x0.50x.196

bearing

x4

x2

x2

1 drop!

Left Side

Left Side

Right Side

Right Side

Molded camber link tower “A” has standard holes, and optional “B” tower has “in-between” hole

options!

!

A

#6588

black grease

Align the gap in the pin retainer

to be opposite of the CVA pin.

!

Build x2 (right and left side)

Build x2 (right and left side)

#1597ca glue

Build x2

Page 16: b44.1 Manual Preflight

16:: Rear Suspension Build - Step 3

:: Rear Suspension Build - Step 4

:: Rear Anti Roll Bar Build - Step 1

73683/16”

axle shims

9608Rear axle

wheel spacer

31286Aluminum ballstud

washer, 1mm

9630.030” ballstud

washer

73691/16”

roll pins

96452-15x1/8”

bhcs

9716Hinge pin

set

8830Anti roll

bar pivots

97804-40x1/2” set screw

x2

x2

Add 1 shim hereif needed.

Build x2

8828Anti rollbar cups

Rear camber

link

8828Ball cup,

short

1mm

Install x2 (right and left side)

Install x2 (right and left side)

Orient the notch to the left

throughout the car. It indicates

which end has the left hand threads!

!

Build x2 (right and left side)

Page 17: b44.1 Manual Preflight

17:: Rear Anti Roll Bar Build - Step 2

:: Battery Tray and Side Body Mounts Build - Step 1

76734-40x5/16”

fhcs

62924-40x3/8”

fhcs

97454-40x.625”

setscrew

9706Battery

post

69514-40x1/8”setscrew

43342-56x5/16”

bhcs

9780Washer 9780

0.55” silver anti-roll bar

9775LiPo

battery tray

9719B44 bodymounts

x2

x4

x4

x4

x2

x2

x2

x2

x2

Trim side body mounts as shown

before installation!Threadlock all setscrews!

!!

Optional black anti-roll bar also

included!

!

#1596

thread lock

#1596thread lock

Install anti-roll bar into #8830 anti-

roll bar pivots until the bar is flush with the end of the pivot!

!

Page 18: b44.1 Manual Preflight

18:: Shocks Build - Step 1

:: Shocks Build - Step 2

:: Shocks Build - Step 3

6465Shock piston(#1)

6465Shock piston(#2)

6469Shock cap

o-ring

7484Shock

internal spacer

7484Shock

internal spacer

7475Front shock body0.89”

7479Rear shock body 1.18”

6469Shock cap

o-ring

9723FT shock

shaft gold0.80” 6417

FT shock shaft gold

1.02”

x46443Bleeder

shock cap(molded)

1777FT shock pivot ball

1777FT shock pivot ball

1777Shock eyelet

4187.030 nylon

washer

4187.030 nylon

washer1777Shock eyelet

Step 9-10

Step 8Step 6-7Step 4-5

Front Shock: 35 wt

Rear Shock: 30 wt

Step 2-3

5407O-ring

7484Lower shock

seal cap

7484Lower shock

seal cap

5407O-ring

6299e-clip

6299e-clip

x2

x2

x2x2

96452-56x1/8”

bhcs

x4Shock Bleeding Steps:1. Before assembly, get each bleed

screw and thread it 1-2 turns into the shock cap. This will make installation easier when you are bleeding your shocks.

2. Pull shock shaft down.3. Fill shock body 3/4 full with silicone

shock fluid.4. Slowly move the shock shaft up and

down to remove air from under the piston.

5. Wait for bubbles to come to surface.6. Fill shock body to top with silicone

shock fluid.7. Place a drop of oil in the cap and on

cap threads.8. Install cap (without bleed screw) and

tighten completely.9. Slowly compress shaft all the way to

bleed excess silicone shodk fluid out the hole in the cap (use rag around-shock to catch excess fluid).

10. Install 2-56 button head screw until snug while shaft is fully compressed (recommend using a high quality .050” wrench such as Factory Team

#1542).

Shock oilShock oil

Front, Build x2 Front, Build x2

Front, Build x2

Front, Build x2 Front, Build x2

Rear, Build x2

Rear, Build x2

Rear, Build x2

Rear, Build x2Rear, Build x2

#1105green slime

#1105green slime

Page 19: b44.1 Manual Preflight

19:: Shocks Build - Step 4

:: Shocks Build - Step 5

:: Servo Build - Step 1

7337Gold

washer

89007Servo horn

ring

3981Ballstud

.20” black,short

6272Dust cover

foam9180Servohorn

1779FT Servo mount

6472Shock

mount nut

6475Rear spring

cup

9724Front offset spring cup

6480Rear Spring,

Green, 1.90lb

6480Front Spring,Silver, 3.85lb

69254-40x1/2”

shcs

69254-40x1/2”

shcs

6472Shock

mount nut

x4

x2

x2

x2x2

x2x2

x2x2

x2

x2

x2

7336Servo

spacers

69174-40x3/8”

bhcs

Build two rear shocks

Build two front shocks

!!

Offset the servo horn by 5-10 degrees

(approximately one notch)! (approximately one notch)!Servo not included!

Servo screwnot included!

x2x2

Build two rear shocks

7416Shock collar o-ring

7416Shock collar

x4

x4

1.7mm

12mm

Use outside holein front arm!

Use inside holein rear arm!

!

!

Page 20: b44.1 Manual Preflight

20:: Servo Build - Step 2 :: Electronics Install - Step 1

:: Electronics Install - Step 3

:: Electronics Install - Step 2

LiPo batteries not included!

ESC not included!

Motor not included!

Receiver not included!

Pinion and setscrew not

included!

31531M3x6mm

bhcs

9803FT Motor

Mount Cam

x2

6338Antenna

tube & cap20.5m

x2

x2

1787FT body

clips, blue

98024-40x.100”

setscrew

9786Battery strap,

carbon fiber

See ESC manufacturer’s instructions for

wiring!

!

69254-40x1/2”

shcs

9802Steel

washer

9802FT Motor mountclamp

x2

x2

7911Servo Link

x262924-40x3/8”

fhcs

Set gear mesh!

Motor tabs should clear top deck!

!

!

Loosenmesh

Tightenmesh

Page 21: b44.1 Manual Preflight

21:: Body, Wheels, Tires Install - Step 1

:: Body, Wheels, Tires Install - Step 2

:: Body, Wheels, Tires Install - Step 2

Carefully apply tire adhesive to the tire bead on

both sides.Do one side at a time, allow it to

dry before gluing the other side!

!

97672.2” Wheel,

front

69538-32

LP steellocknut

9769Proline Holeshot 2.0

M3 compound w/ insert, front

x2

x2

x2

x2

x2

69528-32

locknut, steel

95892.2” Wheel,

rear

#1597

ca glue#1597

ca glue

9590Proline Holeshot 2.0

M3 compound w/ insert, rear

x2

Punisher undertray

by Jconcepts

Add hole

Add hole

Add hole

Slide undertray in between the

front bumper and the chassis!

!Trim along

lines!

!3mm or .125” holes on marks

Page 22: b44.1 Manual Preflight

22:: Body, Wheels, Tires Install - Step 3

:: Body, Wheels, Tires Install - Step 4

:: Body, Wheels, Tires Install - Step 5

Punisher body by

JConcepts

x2

x2

x2

9718Rear

bumper

76734-40 x 5/16”

fhcs

76734-40 x 5/16”

fhcs

6472nylon nut

1736FT body

clips, blue

1736FT body

clips, blue

9729Wing shims

9772High downforce

wing, 6.5”

Painting Tips:Body : Your B44.1 FT comes with a clear polycarbonate body. You will need to prep the body before you can paint it. Wash the inside thoroughly with warm water and liquid detergent. Dry the body using a clean, soft, lint-free cloth. Use the supplied window masks to cover the windows from the INSIDE of the body (RC cars get painted from the inside). Using high quality masking tape, apply tape to the inside of the body to create a design. Spray (either rattle can or airbrush) the paint to the inside of the body (prefferably dark colors first, lighter colors last).

NOTE: use ONLY paint that is recommended for use with (polycarbonate) plastics. If you don’t, you candestroy the plastic body!!!!).

After painting, cut the body along the trim lines. Make sure to drill or use a body reamer to make the holes for the body mounts and antenna!

Use the screw for the servo mount for the opposite side!

!

Page 23: b44.1 Manual Preflight

23:: Tuning TipsTips for Beginners:

Before making any changes to the standard setup, make sure you can get around the track without crashing. Changes to your vehicle will not be beneficial if you can’t stay on the track. Your goal is consistent laps.

Once you can get around the track consistently, start tuning your vehicle. Make only ONE adjustment at a time, testing it before making another change. If the result of your adjustment is a faster lap, mark the change on the included setup sheet (make adddtional copies of the sheet before writing on it). If your adjustment results in a slower lap, revert back to the previous setup and try another change.

When you are satisfied with your vehicle, fill in the setup sheet thoroughly and file it away. Use this as a guide for future track days or conditions.

Front Arm Hole:

The kit silver springs and outside front arm hole will work best in most cases. Moving the shock to the inside hole on the front arm requires you to add another down travel limiter to the front shocks, so there should be two down travel limit-ers in each shock. You should also change to a stiffer spring to account for the difference in leverage on the shock.

Front Ride Height:

The standard front ride height setting is 21mm. Check the ride height by lifting up the entire car about 8-12 inches off the bench and drop it. After the suspension “settles” into place, raise or lower the shock collars as necessary until there is 21 mm gap from the bottom of the chassis to the ground.

Anti-Squat:

Anti-squat denotes the angle of the rear arms relative to the ground. Zero anti-squat means that the rear arms are flat, parallel with the ground. The kit setting is 2 degrees, and can be reduced to 1 degree by removing the included #4 washer underneath the arm mount. You can add another #4 washer so that there is two washers underneath the arm mount to get 3 degrees of anti-squat. Adding anti-squat tends to make the car “rotate” more in corners, but doesn’t handle as well through the bumps. 1 degree will be better in bumpy sections.

Rear Camber Link Length & # of Washers under Ballstud:

Changing the length of the camber link is considered a bigger step than adjusting the ballstud height on the rear chassis brace. Typically shortening the camber link (or lowering the ballstud) will give the rear end less roll and the car will tend to accelerate or “square up” better. Lengthening the camber link (or raising the ballstud) will give the rear more roll and more cornering grip. To raise the ballstud, remove washers from in-between the ballstud and upper deck. You should normally use the kit setting and only adjust the ballstud height

Differential:

Adjust the differential (AKA ‘diff’ for short) as noted in the assembly instructions. Adjusting the rear diff is not meant to be a tuning option. If you can hear the diff making a “barking” or “chirping” sound on jump landings or under acceleration, either your diff is set too loose or your slipper clutch is set too tight. The front diff can go out 1/16” turn to get more steering.

Slipper Clutch:

The assembly instructions give you a base setting for your clutch. To preserve the differentials, always start with the slipper on the loose side and slowly tighten the adjustment nut until it is set. To adjust the slipper, remove the body and insert a 2mm (or 5/64”) hex wrench through the center of the top deck (or through the bottom slot in the chassis). Then, grab both of the rear wheels and rotate forwards to tighten and backwards to loosen. As you spin the wheels, you’ll feel the motor click every ¼ of a wheel revolution. At the track, tighten or loosen the nut in 2 click increments until you hear only a faint slipping sound for 1-2 feet on takeoffs.

Front Camber Link Length & Number of Washers Under Ballstud:

Changing the length of the camber link is considered a bigger step than adjusting the ballstud height. Typically shortening the camber link (orlowering the ballstud) will give the front end less roll and quicken steering response. Lengthening the camber link (or raising the ballstud) will give the front more roll and slower steering response. To raise the ballstud, remove washers from between the ballstud and upper deck.

Front Camber:

A good starting camber setting is –1 degrees. Use the included #1719 camber gage to set your camber. Positive camber, where the top of the tire is leaning out, is typically not recommended.

Front Toe-In:

Zero degree toe-in (tires pointing straight forward) is the setting that should be used in almost all track conditions. Occasionally you can increase turn in by adding a little toe-out (front of tires point slightly out). Front toe in is not a typical tuning adjustment used by The Team.

Page 24: b44.1 Manual Preflight

24:: Tuning Tips (cont.)Rear Hub Spacing:

You have 3 options for rear hub spacing, FORWARD, MIDDLE, & BACK. The kit setting is FORWARD, which provides the most rear traction and will be used most often. For improved handling in bumps or rhythm sections, try moving the hubs to MIDDLE or BACK. This can also make the car handle better in 180 turns.

Rear Anti-Roll Bar:

The #9780 B44 anti-roll bar kit (a.k.a. swaybar) allows you to add roll resistance to the rear end with minimal effect on handling over bumps and jumps. The anit-roll bar is very helpful when trying to tune the suspension. The black bar is the softest (.047” wire) and the silver (.055” wire) is the standard. It is popular to run a rear anti-roll bar in 4wd to help the car square up more out of turns.

Rear Arm Hole:

The inner hole in the arm tends to work the best over the bumps and jump sections. Changing to the outer hole in the rear arm will tend to make the rear end feel more “locked in” and less responsive. Making this change to the outer hole requires you to remove the downtravel limiters from the rear shocks.

Setup Sheets:

Most often, the best way to get your car handling right is to go to our website www.rc10.com and click on the links to Setup Sheets, then RC10B44.1 setups. Our team of professional drivers help develop these setups at National events. Also, most drivers have a “base” setup that they use as a starting point for every event. Try running some of our base setups OR look for track conditions and tires that are similar to your local track and mimic that setup. Remember, each adjustment has a purpose, so copy everything from the setup sheet and then make adjustments based on the recommendations in this manual.

Battery Setup:

The B44.1 is designed to use LiPo saddle pack batteries. Follow your ESC and battery manufacturer’s recommendations for wiring.

Rear Ride Height:

The rear ride height setting you should use most often is 20 mm (the rear arms appear level when looking from the rear). Check the ride height by lifting up the entire car about 8-12 inches off the bench and drop it. After the suspension “settles” into place, raise or lower the shock collars as necessary until there is 20 mm gap from the bottom of the chassis to the ground. Note: Check the ride height gap at the rear end of the carbon fiber chassis, not at the rear chassis plate which is raised for more ground clearance. The chassis should look level from the side.

Steering Servo ChartAssociated

* Not all servo’s are listed* Make sure servo linkage clears the servo through full travel in both directions. Use #7336 servo spacers to adjust the servos position

XP-1015, XP-1313 F

F

F

F

A

A

H

H

J

J

J

# 9180servo arm

94102

HS-5625MG, HS-5645MG, HS625MG, HS645MG

Z4725, Z4750, Z2750, Z8450, Z8550, NES-4750

Z250, Z550

S9204, S9250, S9450, S148

S3003, S9202, S9101

S9404

94738, 94157, 94158, 94257, 94258, 94357, 94358, 94452, 94453, 94751, 94755

HS-322HD, HS-325HB, HS-965, HS-985MG, HS-5965, HS-5985MG, HS-425BB, HS-422

PS-401, PS-2001, PS-2004, PS-2015, PS-2173, PS-2174, PS-2123, PS-2143, PS-2144

Airtronics

Airtronics

Hitec

Hitec

JR

JR

Futaba

Futaba

Futaba

KO

Page 25: b44.1 Manual Preflight

25:: Shocks

:: Shock Springs

:: Differentials

:: Shock Oil

:: Lubes & Adhesives / Decals / Misc.

17771780418754076299641764436465646964726475692574747475747874797484964597239724

4412812141444622221612

1581

1582

649364946496649782326478648064816482743474357436

1

1

Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.

5420542154225423542454255426542754285429543054315432543354345435543654375438

1105159615976588659166366727

7167173816382038349777

2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.

1111112

111121

23303911391439766573657465796581658269099734

2112162

12121

FT Blue Aluminum Shock Pivot Ball/EyeletFT Blue Aluminum Shock Bushing, std.030 Nylon WasherRed O-Rings 1/8” E-ClipsFT Shock Shaft Gold 1.02”Bleeder Shock Caps 1/10 w/screwsShock Pistons, 4 each of #1,2, & 3Black Shock Cap O-RingShock Mount NutSpring Cup (used on rear)4-40 x 1/2“ SHCSV2 Threaded Shocks 0.89” CompleteV2 Threaded Shock Bodies 0.89”V2 Threaded Shocks 1.18” CompleteV2 Threaded Shock Bodies 1.18”V2 1/10th Shocks Rebuild Kit (rebuilds 4)2-56 x 1/8” bhcsFT Shock Shaft Gold 0.80”Offset Spring Cups (used on front)

Factory Team Buggy Front Spring Kit. I pair of green, silver, blue, black front springsFactory Team Truck Rear Spring Kit. I pair of green, silver, blue, gold, red rear springsFront Buggy Spring Brown 2.80 lb (Kit)Front Buggy Spring Green 3.50 lbFront Buggy Spring Silver 3.85 lbFront Buggy Spring Blue 4.20 lbFront Buggy Spring Black 3.20 lbRear Spring Silver 2.10 lbRear Spring Green 1.90 lb (Kit)Rear Spring Black 1.74 lbRear Spring Gray 2.33 lbRear Spring Blue 2.55 lbRear Spring Gold 2.75 lbRear Spring Red 2.95 lb

10 Weight Silicone Shock Oil20 Weight Silicone Shock Oil30 Weight Silicone Shock Oil40 Weight Silicone Shock Oil22.5 Weight Silicone Shock Oil80 Weight Silicone Shock Oil27.5 Weight Silicone Shock Oil15 Weight Silicone Shock Oil25 Weight Silicone Shock Oil35 Weight Silicone Shock Oil45 Weight Silicone Shock Oil55 Weight Silicone Shock Oil32.5 Weight Silicone Shock Oil37.5 Weight Silicone Shock Oil42.5 Weight Silicone Shock Oil50 Weight Silicone Shock Oil60 Weight Silicone Shock Oil70 Weight Silicone Shock Oil47.5 Weight Silicone Shock Oil

FT Green Slime Shock LubeFT Locking AdhesiveFT Tire Adhesive, mediumBlack Grease - 4ccS.Diff Lube - 4ccSilicone Grease - 4ccServo Tape

Reedy 2009 Sticker SetReedy Powered Logo DecalAmerican Bumper StickerAE Logo Decal SheetAE Blue Embossed Logo StickerB44.1 Decal Sheet

Diff T-nutTrans. Shim SetDifferential Ring Gear & Drive Pinion Gear3/8 x 5/8” RS Ball BearingDiff Thrust Washer & Bolt5/64” Diff Thrust BallsDiff Drive Rings3/32” Carbide Diff BallsDiff Thrust SpringDiff Bearing 3/16 x 5/16”B44 Outdrives, Set

6469

6472

6443

9645

1780

6299

62997416

6925

7416

1777

3976

3911

3911

2330

6582

9734

6579

6579

9734

6573

6573

6573

3911

3911

3911

3911

6574

6909

6581

3914

6909

3976

1777

Front9724Rear6475

4187

6465

5407

Front7475Rear 7479

Front9723Rear 6417

54077484

7484

Page 26: b44.1 Manual Preflight

26:: Slipper / Spur Gears / Pinions

:: Pinions

:: Anti-Roll Bars :: Turnbuckles

165473817485748679359603964996509651965296539711973697409742

825282538254825582568257825882598260826182628263826482658266826782688269

412122111112111

111111111111111111

140414067230

Pr.Pr.12

6951882888309780

6111

FT Axle PinsCVD Rebuild KitFT V2 Slipper HubsFT V2 Slipper Spring and Washer.187 x .50 x .196” BearingSlipper Pad72T 48P Spur Gear75T 48P Spur Gear81T 48P Spur Gear (Kit)78T 48P Spur Gear84T 48P Spur GearB44 Bearing InsertB44 Slipper ShaftB44 Slipper NutB44 Slipper Drive Cups

15T 48P Pinion Gear16T 48P Pinion Gear17T 48P Pinion Gear18T 48P Pinion Gear19T 48P Pinion Gear20T 48P Pinion Gear21T 48P Pinion Gear22T 48P Pinion Gear23T 48P Pinion Gear24T 48P Pinion Gear 25T 48P Pinion Gear26T 48P Pinion Gear27T 48P Pinion Gear28T 48P Pinion Gear29T 48P Pinion Gear30T 48P Pinion Gear31T 48P Pinion Gear32T 48P Pinion Gear

FT Blue Titanium Turnbuckles 1.775” / 45mmFT Blue Titanium Turnbuckle 2.00 / 51mm”Ball Cups, Large

4-40 x 1/8” Set ScrewAnti Roll Bar Cups, SetAnto Roll Bar Pivots (with setscrews), SetB44 Anti Roll Bar Kit

9742

1654

9740

9741

7486

9736

9711

7935

7485

7485

9736

7935

9711

9736

1654

96039603

9651

9742

9742

7381

7381

8828

8828

8828

8830

6951

883097809780

7230

1404

1406

1406

7230

7230 7230

7230 7230

9780

6951

8828

Page 27: b44.1 Manual Preflight

27:: Front and Rear Gearboxes

:: Steering

:: Front and Rear Shock Towers

39033911391939774334629968607381799697339747976097619780

21128

1261212111

177938743981627262766277629269177336733779119180963097439744974689007

046

2866661411

101111

173617804449691774137738787497039704971997299772

645666811111

FT Servo Mount, blueBlock Carrier BushingsBallstud .20” Black, shortFoam Ballend Dust CoversBallstud .20” Silver, shortBallstud .30” Silver, short4-40 x 3/8” FHCS4-40 x 3/8” BHCSSteering Servo Mount Kit.250 x .125 x .015” WasherSteering Servo LinkServo Horns, MoldedBallstud WasherB44 Steering SetB44 Steering HardwareB44 Steering Bearing SetSteering Servo Ring, blue

FT Body Clips, Short, blueFT Blue Alum. Shock Bushing, std4-40 x 3/16” Alum. Locknut4-40 x 3/8” BHCS4-40 x 3/4” BHCS4-40 x 7/8” SHCS4-40 x 7/16” SHCSB44 Front Shock TowerB44 Rear Shock TowerB44 Body MountsB44 Wing MountsHigh Downforce Wing 6.5”

68606860

9733

9733

6299

6299

3903

3903

3919

39193911

3911

3911

3977

39777996

7996

9761

9761

7381

73817381

7381 9747

9760

9733

6292

6292

9743

97439746

9746

9746

9744

9743

97439743

9744

97443874

9743

6917

69179630

96306277

6277

9744

9744

97447911

9180

1779

17796292

6917

6917

6917

6917

73367337

7337

1736

17367874

9719

6917

6917

6917

6917

6917

97036917

74137413

74137413

97041780

1780

1780

9772

9729

9729

97299729

7738

4449

7336

6292

39816272

6272

6276

6272

6272

7911

7911

89007

9733

68606860

68606860

6860

6860

6860

6860

4334

43349780

9780

6860

6860

Drive PinionsTrans. Shim SetInput Shaft Hardware3/16 x 3/8” RS Ball Bearing2-56 x 5/16” BHCS1/8” Small E-ClipsFT 4-40 x 3/8” SHCS, blueCVD Rebuild KitPosilock QC Pin RetainerB44 Transmission CaseB44 Front CVA BoneB44 Center Bone, RearB44 CVA Input ShaftB44 Anti Roll Bar Kit

Page 28: b44.1 Manual Preflight

28:: Front and Rear Top Plates

:: Center Bulkhead and Motor Mount

1736433444496277628862926338691769256936970197029714971931113

62926924692597099712980098019802980331531

6661111116

FT Body Clips, Short, blue2-56 x 5/16” BHCS4-40 x 3/16” Alum. LocknutBallstud .30” Silver, short4-40 x 1/4” BHCS4-40 x 3/8” FHCSAntenna Tube 12”, black4-40 x 3/8” BHCS4-40 x 1/2” SHCSWashers, Alum. #4B44 Front Top DeckB44 Rear Top DeckB44 Shock Tower MountsB44 Body MountsAntenna Mount

4-40 x 3/8” FHCS4-40 x 3/8” SHCS4-40 x 1/2” SHCSB44 Center BulkheadB44 Center Bulkhead CapB44 FT Cam Motor Mount SetB44 FT Cam Motor MountB44 FT Motor Mount ClampB44 FT Motor Mount CamM3 x 6mm BHCS

FT Body Clips, Short, blue

4-40 x 3/16” Alum. LocknutBallstud .30” Silver, short

Antenna Tube 12”, black

B44 Shock Tower Mounts

17369719

6292

9714

4449

44496936

6936

6277

6924

6924 6924

69249712

9709

6292

6292

6292

6292 9801

9803

31531

31531

9802

9802

9802

9802

6925

9800

6925

6277

6288

6917

6917

4449

4449

9714

6925

6925

6925

6292

6292

6292

6292

9701

9702

6936

69366277

6277

6292

629231113

6338

43344334

685666166

1011111

Page 29: b44.1 Manual Preflight

29:: Front Suspension

:: Rear Suspension

22213977398344496272627769537369738179969645964797159716972097229747974897509751

6265

286641264

Pr.1

Pr.Pr.2222

397739836272693269527368736973817933793579969608963096459716975497649864987231286

26

2866

14412222

10612

Pr.Pr.1

4 ea.

3/16 x 3/8” RS Ball BearingBallstud .30” Black, shortFoam Ballend Dust Covers4-40 x 5/16” SHCS8-32 Locking Nut, Steel3/16” Axle Shims1/16” Universal Roll PinsCVD Rebuild KitCrush Tube GT2.187 x .50 x .196” BearingPosiLock QS Pin RetainerRR Axle Wheel SpacerBallstud Washer2-56 x 1/8” BHCSB44 Hinge Pin SetB44 Rear CVA BoneB44 Rear ArmB44 FT Aluminum Hub, 0˚B44 FT Aluminum Hub Tower SetAlum. Ballstud Washer (1mm, 2mm)

1222210612

Pr.Pr.1

4 ea.Alum. Ballstud Washer (1mm, 2mm)

9716

9716

9716

9716 9764

2221

2221 62726272

6272

7996

7996

3977

7935

7933

7368

9630

9864

3983

9872

6932

31286

7369

7369

7381

7381

7381

7381

9754

9748

9747

6277

4449

4449

6953

9750

9751

3977

3977

9647

9647

9720

9722

3983

6952

9608

9645

9645

9715

4-40 x 7/16” BHCS3/16 x 3/8” RS Ball BearingBallstud .30” Black, short4-40 x 3/16” Alum. LocknutFoam Ballend Dust CoversBallstud .30” Silver, short8-32 LP Steel Locknut1/16” Universal Roll PinsCVD Rebuild KitPosiLock QC Pin Retainer2-56 x 1/8” BHCSB44 Steering Block BushingB44 Front ArmsB44 Hinge Pin SetB44 Caster BlockB44 Steering BlockB44 Front CVA BoneB44 Front CVA AxleB44 Axle Drive HexB44 Front Crush Tube

Page 30: b44.1 Manual Preflight

30:: Chassis and Battery Mounts

17874449629264726915691769367673964597069713971497189719972697459765977497759786

256466

1064211

1 ea.2116112

FT Battery Strap Thumbscrews4-40 x 3/16” Alum. Locknut4-40 x 3/8” FHCSShock Mount Nuts4-40 x 5/8” FHCS4-40 x 3/8” BHCSWashers, Alum. #44-40 x 5/16” FHCS2-56 x 1/8” BHCSB44 Battery PostB44 Front BulkheadB44 Shock Tower MountsB44 Front & Rear BumperB44 Body MountsB44 Rear Chassis Plate, 3˚ arm mountB44 Servo Link and Setscrew4-40 x 7/16” FHCSB44.1 LiPo ChassisB44.1 LiPo Battery TrayB44 Battery Strap Carbon Fiber

1787

1787

9745

9745

9786

9786

9745

9745

9706

9706

9775

97756292

6292

6292

6292

9706

9706

6472

6472

9775

6292

6292

6292

9718

6917

6917

6292

6472

7673

9774

9719

9719

7673

7673

6292

4449

9714 9713

9645 9765

6292

1787

1787

97266292

7673

9718

4449

4449

9645

4449

4449

9726

6936

6936

6292

6292

6915

69159765

Page 31: b44.1 Manual Preflight

31:: Factory Team and Option Parts

1404140614111598165417281729173017311732173317361777177917801787641769036906693769437416747474757478747974847996

9608B9710972197239774977597769779978397849786978797959796979797989799980098019802980398649865986698679872

2221411

Pr.Pr.18612421

Pr.Pr.64

Pr.Pr.Pr.Pr.Pr.1221

Pr.111111121222221111

Pr.Pr.Pr.Pr.1

Ti Turnbuckle 1.775” BlueTi Turnbuckle 2.00” BlueTi Turnbuckle 0.75” BlueFT Blue Aluminum Shock CapFT Solid Axle PinsFT HD Front One-Way SetFT HD One-Way Housing SetFT HD One-Way Outdrive CupFT Bearings for HD One-WayFT HD One-Way Ring GearFT HD One-Way ShimsFT Short Body Clips BlueFT Blue Aluminum Ball/Eyelet SetFT Servo Mount Blue AluminumFT Aluminum Shock BushingBattery Strap ThumbscrewFT Shock Shaft Gold 1.02”3/8 x 5/8“ PTFE Bearings3/16 x 3/8” PTFE BearingsFT Blue 4-40 LocknutsFT Blue 8-32 LocknutsThreaded Shock CollarFT V2 .89” Threaded ShocksFT V2 .89” Threaded BodiesFT V2 1.18” Threaded ShocksFT V2 1.18” Threaded BodiesFT V2 1:10 Shock Rebuild KitCVA Pin RetainerRR Axle Wheel Spacer, blueB44 Alum. Center BulkheadB44 Alum. Caster BlocksFT Shock Shaft Gold 0.80”B44.1 LiPo ChassisB44.1 LiPo Battery TrayB44.1 LiPo Ballast WeightB44 Complete Bearing SetB44 Alum. Front Tower MountB44 Alum. Rear Tower MountB44 Carbon Battery StrapChassis Protective SheetTi Nitride Ballstuds 4-40 x 0.20” LongTi Nitride Ballstuds 4-40 x 0.30” LongTi Nitride Ballstuds 4-40 x 0.40” LongTi Nitride Ballstuds 4-40 x 0.20” ShortTi Nitride Ballstuds 4-40 x 0.30” ShortB44 Cam Motor Mount SetB44 Cam Motor MountB44 Motor Mount ClampB44 Motor Mount CamB44 FT Aluminum Hub, 0˚B44 FT Aluminum Hub, 0.5˚B44 FT Aluminum Hub, 1˚B44 FT Aluminum Hub, 1.5˚B44 FT Aluminum Hub Tower Set

:: Reedy Motors and ESC’s

:: XP Electronics

:: Reedy Batteries

:: Reedy Accessories

916917918919936937938939

2910729125291262913229140291412916629177292092921029211292122922129222

11111111

11111111111111

302303627632633634637686710712

605610654655656657658659660661662663664716

SP35MSP35L

SP35XLSP35XXL

SP35XXXLSP36MSP36L

SP36XLSP36XXL

SP36XXXLSP417SP418

1111111111

11111111111111111111111111

540R Brushless Motor 3300kV540R Brushless Motor 3900kV540R Brushless Motor 4900kV540R Brushless Motor 6100kVXP SC450-BL/Reedy 540R 3300kV ComboXP SC450-BL/Reedy 540R 3900kV ComboXP SC450-BL/Reedy 540R 4900kV ComboXP SC450-BL/Reedy 540R 6100kV Combo

S1903 Metal Gear SetS1903MG ServoS2008MG ServoSHV1504MG ServoXP SC200 Brushed ESC XP SC450-BL Brushless ESCXP DS1313 Digital ServoXP DS1015 Digital ServoGear Set, DS1313Gear Set, DS1015Servo Case , DS1313 / DS1015Accessory Pack, DS1313 / DS1015XP3SS 2.4GHz Radio SystemTRS401SS 2.4GHz 4Ch Receiver

AA Alkaline 1.5V (4)AA 2700mAh NiMH 1.2V Rechargeable LiPo 60C 5200mAh 7.4V SPTX Lightweight Battery 1350mAh 11.1VTX Battery - 3PK, M11 3000mAh 11.1VTX Battery - Helios, Z1 2400mAh 11.1VTX Battery - M11X 2500mAh 7.4VLiPo 40C+ 4200mAh 7.4V SPLiPo 5100mAh 7.4V 35C SP ROAR SpecLiPo 4200mAh 7.4V 35C SP EFRA Spec

Motor Cooling Fans (2)AC/DC NiMH Peak Charger4.0mm plugs (2M, 2F) 4.0mm plugs (2M, 10F) 4.0mm plugs (10F)4.0mm plugs (100F)4.0mm plugs (10M)4.0mm plugs (30M)3.5mm plugs (3M, 3F)3.5mm plugs (10F)3.5mm plugs (100F)3.5mm plugs (10M)3.5mm plugs (30M)Reedy 09 Decal SetReedy Logo T-Shirt - White MReedy Logo T-Shirt - White LReedy Logo T-Shirt - White XLReedy Logo T-Shirt - White XXLReedy Logo T-Shirt - White XXXLReedy Logo T-Shirt - Black MReedy Logo T-Shirt - Black LReedy Logo T-Shirt - Black XLReedy Logo T-Shirt - Black XXLReedy Logo T-Shirt - Black XXXLFactory Team 1/10 Motor Storage BagFactory Team 1/10 Car Carrier Bag

:: LRP Brushless MotorsLRP50642LRP50652LRP50662LRP50672LRP50682LRP50687LRP50692LRP50702LRP50712LRP50722LRP50832LRP50842LRP50852LRP50862

11111111111111

LRP X-12 9.5 TurnLRP X-12 8.5 TurnLRP X-12 7.5 TurnLRP X-12 6.5 TurnLRP X-12 5.5 TurnLRP X-12 5.0 TurnLRP X-12 4.5 TurnLRP X-12 4.0 TurnLRP X-12 3.5 TurnLRP X-12 3.0 TurnVector X-12 Stock-Spec 10.5 TurnVector X-12 Stock Spec 13.5 TurnVector X-12 Stock Spec 17.5 TurnVector X-12 Stock Spec 21.5 Turn

Page 32: b44.1 Manual Preflight

32:: LRP Speed Controls

:: LRP Brushless Combos

:: LRP Charger, Power Supply, Balancer, Iron

LRP8320LRP8325LRP8337LRP80100LRP80150LRP80400LRP80800LRP80830LRP80900LRP80910LRP80950LRP86500LRP80905LRP80955LRP80460

LRP80640LRP80641LRP80642LRP80643LRP80644LRP80645LRP80646LRP80647LRP80648LRP80649LRP80654LRP80655LRP80656LRP80657LRP80658LRP80659LRP80673LRP80674LRP80675

LRP41281LRP41555LRP43150LRP45200LRP65800LRP65802LRP65803LRP65804

111111111111111

1111111111111111111

11111111

AI Super ReverseAI Pro ReverseAI Bullet ReverseAI Brushless ReverseAI Brushless Pro ReverseSPX Brushless Super ReverseV 8.1Quantum Competition 3SXX Competition Speed ControlSXX Stock-Spec Speed ControlSXX TC-Spec Speed ControlNEXXT 4X escSXX Competition V.2SXX TC-Spec V.2Ultimo Drift

SXX TC / X-12 3.0 TurnSXX TC / X-12 3.5 TurnSXX TC / X-12 4.0 TurnSXX TC / X-12 4.5 TurnSXX TC / X-12 5.0 TurnSXX TC / X-12 5.5 TurnSXX TC / X-12 6.5 TurnSXX TC / X-12 7.5 TurnSXX TC / X-12 8.5 TurnSXX TC / X-12 9.5 TurnSXX COMP / X-12 5.0 TurnSXX COMP / X-12 5.5 TurnSXX COMP / X-12 6.5 TurnSXX COMP / X-12 7.5 TurnSXX COMP / X-12 8.5 TurnSXX COMP / X-12 9.5 TurnSXX Stock-Spec / X-12 Stock-Spec 10.5 TurnSXX Stock-Spec / X-12 Stock-Spec 13.5 TurnSXX Stock-Spec / X-12 Stock-Spec 17.5 Turn

Quadra Pro 2 ChargerPulsar Touch Competition ChargerPower Supply CompetitionLiPo Parallel BalancerHigh Power Solder StationSoldering Tip 5mmSoldering Tip 1.2mmSoldering Handle

:: LRP Misc.LRP50620LRP50621LRP50622LRP50623LRP50624LRP50625LRP50626LRP50632LRP50633LRP50634LRP80135LRP82520LRP82511LRP819307LRP819310LRP819315LRP819320

11111111111111111

X-12 Replacement Ball BearingsX-12 Optional Ceramic Ball BearingsX-12 Small parts SetX-12 PreciSensor UnitX-12 Replacement alum Front canX-12 Lightweight Alum CanX-12 Alum Rear CoverX-12 12.0mm sintered rotorX-12 12.5mm sintered rotorX-12 13.0mm sintered rotorBEC stabilizing capacitorBrushless/Brushed Cooling SetBrushless Low Profile Fan70mm High Flex Sensor Wire100mm High Flex Sensor Wire150mm High Flex Sensor Wire200mm High Flex Sensor Wire

:: Apparel

:: 1/18 Kits and RTR’s

:: 1/12, 1/10 Kits and RTR’s

20100201012010320105201062011020115201182012020130

203320424019702070237027702970307032703470367037704070417043704470807092802080219034903690389039906120515301053010630111

** Use part number plus the desired size when ordering!

1111111111

11111111111111111111111111111

SP35**SP36**SP58**SP59**SP60**SP61**SP62**SP63**SP64**SP65**SP100SP101SP102SP103

SP410**SP415SP416SP417SP418

SP420**715

110684

1111111111111111111

Pr.11

RC18T RTR (ready-to-run)RC18T2 2.4ghz RTR (ready-to-run)RC18B2 - RC18T2 Team KitRC18B RTR (ready-to-run)RC18B2 2.4ghz RTR (ready-to-run)RC18MT RTR (ready-to-run)RC18R Kamino RTR (ready-to-run)RC18R Niteline RTR (ready-to-run)SC18 RTR (ready-to-run)RC18LM RTR (ready-to-run)

FT Nitro TC3 KitNitro TC3 RTR Plus (ready-to-run)FT 12R5.1 KitRC10T4 Team Truck KitRC10T4.1 FT KitSC10 2WD Short Course Race Truck KitSC10 Associated/RC10.com Truck RTR (ready-to-run)SC10 KMC Wheels Race Truck RTR (ready-to-run)SC10 Ready Lift RTR (ready-to-run)SC10 FT KitRC10T4.1 RTR 2.4GHz Brushed (ready-to-run)RC10T4.1 RTR 2.4GHz Brushless (ready-to-run)SC10 RTR, 2.4ghz Brushless Lucas Oil BodySC10 RTR, 2.4ghz Brushless Speed Tech/Bully Dog BodySC10 RTR, 2.4ghz Brushless Pro Comp BodySC10 RTR, 2.4ghz Brushless Rockstar / Makita BodyFT GT2 Nitro Truck KitGT2 RS Truck Nitro RTR (ready-to-run)FT RC10R5 KitFT RC10R5-OVAL KitRC10B4 Buggy Team KitRC10B4.1 FT KitRC10B4.1 RTR 2.4GHz Brushed (ready-to-run)RC10B4.1 RTR 2.4GHz Brushless (ready-to-run)FT B44.1 4WD Buggy KitMGT 3.0 Nitro Monster Truck RTR (ready-to-run)FT TC5R Rubber Tire Edition 4WD Touring Car KitFT TC6 4WD Touring Car KitTC4 4WD Touring Car RTR (ready-to-run)

Reedy 09’ White T-Shirt (M, L, XL, XXL, XXXL)Reedy 09’ Black T-Shirt (M, L, XL, XXL, XXXL)AE Logo Black T-Shirt (M, L, XL, XXL)AE Logo Blue T-Shirt (M, L, XL, XXL)AE Hooded Sweatshirt (S, M, L, XL, XXL)AE Vertigo Hooded Sweatshirt (S, M, L, XL, XXL)AE Vertigo Long Sleeve T-Shirt (S, M, L, XL, XXL)AE Vertigo White T-Shirt (S, M, L, XL, XXL)AE Vertigo Blue T-Shirt (S, M, L, XL, XXL)AE Vertigo Black T-Shirt (S, M, L, XL, XXL)1/8 Inner and Outer Boxes Only, Set1/8 Inner Boxes Only, Set1/10 Inner and Outer Boxes Only, Set1/10 Inner Boxes Only, SetAE Hats Black (S-M, L-XL, XXL-XXXL)1/8 Car Carrier Bag Only1/10 Car Carrier Bag Only1/10 FT Motor Bag1/10 FT Car Carrier Bag with Boxes, SetAE Pit Gloves (M, L, XL)Reedy 2009 Track BannerTeam Associated Track Banner

Page 33: b44.1 Manual Preflight

33:: 1/8 Kits and RTR’s20503

20504

809028090480905809128091580920

80921

80922

80923

80924

80925

80932

1

1

111111

1

1

1

1

1

1

Limited Edition MGT 4.60 Nitro RTR, w/flag body (ready-to-run)Limited Edition MGT 8.0 Nitro RTR, w/flag body (ready-to-run)FT RC8B Nitro Buggy KitFT RC8Be Electric Buggy KitRC8RS “Race Spec” Nitro Buggy RTR (ready-to-run)RC8T Championship EditionRC8T-RS “Race Spec” Nitro Truggy RTR (ready-to-run)SC8 Short Course Race Truck, Red Bull Nitro RTR (ready-to-run)SC8 Short Course Race Truck, Lucas Oil Nitro RTR (ready-to-run)SC8 Short Course Race Truck, KMC Wheels Nitro RTR (ready-to-run)SC8 Short Course Race Truck, Bully Dog Nitro RTR (ready-to-run)SC8 Short Course Race Truck, AE Team Nitro RTR (ready-to-run)SC8 Short Course Race Truck, Pro Comp Nitro RTR (ready-to-run)SC8e Short Course Race Truck Rockstar/Makita RTR (ready-to-run)

:: Contact Information

:: Tools111114491450154115421543154415451546154715481551155315541561156215631564156515661567158915901592171917373718371937203987642969567709

1111111111111111111111111112121211112

Associated Electrics, Inc.26021 Commercentre Drive

Lake Forest, CA 92630-8853 USAhttp://www.TeamAssociated.com

http://www.RC10.comhttp://twitter/Team Associated

http://bit.ly/AEonFacebook

call: (949) 544-7500fax: (949) 544-7501

Check out the following web sites for all of our electric kits, current products, new releases, setup help, tips, and racing info!

www.TeamAssociated.com. - www.RC10.com

FT Turnbuckle WrenchOffroad Ride Height GaugeFT Ride Height GaugeFT Hex Driver Set, (7 pcs)FT .050” Silver Hex DriverFT 1/16” Black Hex DriverFT 1.5mm Purple Hex DriverFT 5/64” Blue Hex DriverFT 3/32” Gold Hex DriverFT 2.5mm Green Hex DriverFT 3mm Red Hex DriverFT Screwdriver SetFT Phillips Silver ScrewdriverFT Silver Spring Hook Tool FT Nut Driver Set, (6 pcs)FT 3/16” Black Nut DriverFT 1/4” Red Nut DriverFT 5.5mm Red Nut DriverFT 11/32” Green Nut DriverFT 7.0mm Silver Nut DriverFT 8mm Gold Nut DriverFT 5/64” Blue Ball Hex DriverFT 3/32” Gold Ball Hex DriverFT Ball Hex Driver Set, (3 pcs)FT Camber + Track Width ToolFT Body Scissors12 Inch Nylon Wire Ties6 Inch Nylon Wire Ties8 Inch Nylon Wire TiesFT Droop GaugeShock Building ToolMolded Tools, Set4 Inch Nylon Wire Ties

Page 34: b44.1 Manual Preflight

34:: Notes

Page 35: b44.1 Manual Preflight

Driver: Date: Track: Event:Conditions: Rev.1Setup Sheet

:: For more setups, visit RC10.com and click on “Setup Sheets”

Front Suspension

Front Shocks

Electronics

Differentials

Front Tires

Race and Vehicle Comments

Other

Rear Tires

Track Info

Rear Suspension

Rear Shocks

Anti Roll Bar:

0.047” Black0.055” SilverNone

Anti Roll Bar:

0.047” Black0.055” SilverNone

Spring: Piston:Shock Oil: Limiter:

Motor & Wind:Pinion:Spur Gear:Batteries:Battery Placement:

Front Diff Setting:Rear Diff Setting:

Tire:Compound:Insert:Wheel:

Qualify: Main: Finish: TQ:Comments:

Tire:Compound:Insert:Wheel:

Smooth: Bumpy: Blue Groove:Traction: High: Medium: Low:Soft Dirt: Grass: Clay: Wet:Dusty: Other:

Radio:Throttle / Brake e.p.a:Throttle / Brake expo:ESC: Throttle Profile:Initial Brake: Drag Brake:Servo: Steering Expo:

Body Type:Wing Type: Wing Angle:

Spring: Piston:Shock Oil: Limiter:

Bumpsteer Washer:

Camber:

Toe:

Ride Height:

Camber:

Toe:

Ride Height:

Notes:

Washers:

Notes:

Wheelbase:LongMediumShort

Aluminum Hub Tower:AB

1

12

12

1

22

I O

Steering Rack:

FrontBack

I O

A B

A CB D

B44.1 Standard Setup

0

-1˚

21mm

1

-1˚

20mm

Measure ride

Silver Green35 wt

Standard JConcepts Punisher6.5” high 9˚Standard

Holeshot 2.0 Holeshot 2.0M3 M3

Standard StandardStandard Standard

30 wt1 1#2 #1

height on back cornerof chassis

Page 36: b44.1 Manual Preflight

36

4-40x5/16” (7673)

4-40x3/8” (6292)

4-40x7/16” (9765)

4-40x5/8” (6915)

2-56x1/8” (9645)

2-56x5/16” (4334)

4-40x1/4” (6228)

4-40x3/8” (6917)

4-40x7/16” (2221)

4-40x3/4” (7413)

4-40 Aluminum Locknut (4449)

4-40 Plastic Nut (6472)

5-40 Nylon Locknut (9744)

8-32 LP Steel Locknut (6953)

8-32 Steel Locknut (6952)

E-clip (6299)

5/64” Diff Thrust Balls (6574)

3/32” Carbide Diff Balls (6581)

Ballstud Washer (9630)

.030” Nylon Spacer (4187)

Servo Mount Washer (7337)

#4 Washer (6936)

Input Shaft Shim - Black (3911)

3/16” Axle Shim - Silver (7368)

Outdrive Shim (3911)

:: Hardware - 1:1 Scale View

Cap Head (shcs)

Top Hat Bushings

Ball Bearings

Notes:

Flat Head (fhcs)

Shims and Washers

Button Head (bhcs)

Nuts (lock/plain)

Clips

Diff Balls

4-40x5/16” (6932)(aluminum ,4145)

4-40x3/8” (6924)(aluminum ,6860)

4-40x7/16” (7874)(aluminum, 7873)

4-40x1/2” (6925)

4-40x7/8” (7738)

3x6mm (6515)(motor mounting screws)

Small Top Hat Bushing (3874)

Large Top Hat Bushing (9647)

Steering Bearing (9746)

3/16x5/16” (6906)

3/16x3/8” (3977)

3/16x1/2” RS (7935)

3/8x5/8” RS (3976)Ballstuds

Silver .20” Short (6276)

Silver .30” Long (6277)

Black .30” Long (3983)

Page 37: b44.1 Manual Preflight

Wheel B

ase Sh

ims

1mm

2m

m

Cam

Hold

er

AB

1º1.5

º2º

Arm

Mount Sh

ims

21

Wheelb

ase

Wheelb

ase

Hex S

pacin

g

Toe

0+ -To

e0+ -

Hex S

pacin

g

Cam

ber

0

+

-

Bum

psteer

Outer B

all

& S

him

s

Outer B

all

& S

him

s

Driver: Date: Track: Event:Conditions: Rev.1Setup Sheet

:: For more setups, visit RC10.com and click on “Setup Sheets”

Front Suspension

Front Shocks

Electronics

Differentials

Front Tires

Race and Vehicle Comments

Other

Rear Tires

Track Info

Rear Suspension

Rear Shocks

Anti Roll Bar:

0.047” Black0.055” SilverNone

Anti Roll Bar:

0.047” Black0.055” SilverNone

Spring: Piston:Shock Oil: Limiter:

Motor & Wind:Pinion:Spur Gear:Batteries:Battery Placement:

Front Diff Setting:Rear Diff Setting:

Tire:Compound:Insert:Wheel:

Qualify: Main: Finish: TQ:Comments:

Tire:Compound:Insert:Wheel:

Smooth: Bumpy: Blue Groove:Traction: High: Medium: Low:Soft Dirt: Grass: Clay: Wet:Dusty: Other:

Radio:Throttle / Brake e.p.a:Throttle / Brake expo:ESC: Throttle Profile:Initial Brake: Drag Brake:Servo: Steering Expo:

Body Type:Wing Type: Wing Angle:

Spring: Piston:Shock Oil: Limiter:

Bumpsteer Washer:

Camber:

Toe:

Ride Height:

Camber:

Toe:

Ride Height:

Notes:

Washers:

Notes:

Wheelbase:LongMediumShort

Aluminum Hub Tower:AB

1

12

12

1

22

I O

Steering Rack:

FrontBack

I O

A B

A CB D

Page 38: b44.1 Manual Preflight

Associated Electrics, Inc.26021 Com

mercentre Dr.

Lake Forest, CA 92630 USAhttp://w

ww

.TeamAssociated.com

http://ww

w.RC10.com

http://twitter/Team

_Associatedhttp://bit.ly/AEonFacebook

call: (949) 544-7500 - fax: (949) 544-7501Check out the follow

ing web sites for all of our kits,

current products, new releases, setup help, tips, and racing info!

ww

w.Team

Associated.com. - w

ww

.RC10.com